--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000e/netdev-2.6.35-ethercat.c Tue Apr 10 19:10:56 2012 +0200
@@ -0,0 +1,6120 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2009 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/vmalloc.h>
+#include <linux/pagemap.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/tcp.h>
+#include <linux/ipv6.h>
+#include <linux/slab.h>
+#include <net/checksum.h>
+#include <net/ip6_checksum.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/if_vlan.h>
+#include <linux/cpu.h>
+#include <linux/smp.h>
+#include <linux/pm_qos_params.h>
+#include <linux/pm_runtime.h>
+#include <linux/aer.h>
+
+#include "e1000-2.6.35-ethercat.h"
+
+#define DRV_VERSION "1.0.2-k4 (EtherCAT)"
+char e1000e_driver_name[] = "ec_e1000e";
+const char e1000e_driver_version[] = DRV_VERSION;
+
+static const struct e1000_info *e1000_info_tbl[] = {
+ [board_82571] = &e1000_82571_info,
+ [board_82572] = &e1000_82572_info,
+ [board_82573] = &e1000_82573_info,
+ [board_82574] = &e1000_82574_info,
+ [board_82583] = &e1000_82583_info,
+ [board_80003es2lan] = &e1000_es2_info,
+ [board_ich8lan] = &e1000_ich8_info,
+ [board_ich9lan] = &e1000_ich9_info,
+ [board_ich10lan] = &e1000_ich10_info,
+ [board_pchlan] = &e1000_pch_info,
+};
+
+struct e1000_reg_info {
+ u32 ofs;
+ char *name;
+};
+
+#define E1000_RDFH 0x02410 /* Rx Data FIFO Head - RW */
+#define E1000_RDFT 0x02418 /* Rx Data FIFO Tail - RW */
+#define E1000_RDFHS 0x02420 /* Rx Data FIFO Head Saved - RW */
+#define E1000_RDFTS 0x02428 /* Rx Data FIFO Tail Saved - RW */
+#define E1000_RDFPC 0x02430 /* Rx Data FIFO Packet Count - RW */
+
+#define E1000_TDFH 0x03410 /* Tx Data FIFO Head - RW */
+#define E1000_TDFT 0x03418 /* Tx Data FIFO Tail - RW */
+#define E1000_TDFHS 0x03420 /* Tx Data FIFO Head Saved - RW */
+#define E1000_TDFTS 0x03428 /* Tx Data FIFO Tail Saved - RW */
+#define E1000_TDFPC 0x03430 /* Tx Data FIFO Packet Count - RW */
+
+static const struct e1000_reg_info e1000_reg_info_tbl[] = {
+
+ /* General Registers */
+ {E1000_CTRL, "CTRL"},
+ {E1000_STATUS, "STATUS"},
+ {E1000_CTRL_EXT, "CTRL_EXT"},
+
+ /* Interrupt Registers */
+ {E1000_ICR, "ICR"},
+
+ /* RX Registers */
+ {E1000_RCTL, "RCTL"},
+ {E1000_RDLEN, "RDLEN"},
+ {E1000_RDH, "RDH"},
+ {E1000_RDT, "RDT"},
+ {E1000_RDTR, "RDTR"},
+ {E1000_RXDCTL(0), "RXDCTL"},
+ {E1000_ERT, "ERT"},
+ {E1000_RDBAL, "RDBAL"},
+ {E1000_RDBAH, "RDBAH"},
+ {E1000_RDFH, "RDFH"},
+ {E1000_RDFT, "RDFT"},
+ {E1000_RDFHS, "RDFHS"},
+ {E1000_RDFTS, "RDFTS"},
+ {E1000_RDFPC, "RDFPC"},
+
+ /* TX Registers */
+ {E1000_TCTL, "TCTL"},
+ {E1000_TDBAL, "TDBAL"},
+ {E1000_TDBAH, "TDBAH"},
+ {E1000_TDLEN, "TDLEN"},
+ {E1000_TDH, "TDH"},
+ {E1000_TDT, "TDT"},
+ {E1000_TIDV, "TIDV"},
+ {E1000_TXDCTL(0), "TXDCTL"},
+ {E1000_TADV, "TADV"},
+ {E1000_TARC(0), "TARC"},
+ {E1000_TDFH, "TDFH"},
+ {E1000_TDFT, "TDFT"},
+ {E1000_TDFHS, "TDFHS"},
+ {E1000_TDFTS, "TDFTS"},
+ {E1000_TDFPC, "TDFPC"},
+
+ /* List Terminator */
+ {}
+};
+
+/*
+ * e1000_regdump - register printout routine
+ */
+static void e1000_regdump(struct e1000_hw *hw, struct e1000_reg_info *reginfo)
+{
+ int n = 0;
+ char rname[16];
+ u32 regs[8];
+
+ switch (reginfo->ofs) {
+ case E1000_RXDCTL(0):
+ for (n = 0; n < 2; n++)
+ regs[n] = __er32(hw, E1000_RXDCTL(n));
+ break;
+ case E1000_TXDCTL(0):
+ for (n = 0; n < 2; n++)
+ regs[n] = __er32(hw, E1000_TXDCTL(n));
+ break;
+ case E1000_TARC(0):
+ for (n = 0; n < 2; n++)
+ regs[n] = __er32(hw, E1000_TARC(n));
+ break;
+ default:
+ printk(KERN_INFO "%-15s %08x\n",
+ reginfo->name, __er32(hw, reginfo->ofs));
+ return;
+ }
+
+ snprintf(rname, 16, "%s%s", reginfo->name, "[0-1]");
+ printk(KERN_INFO "%-15s ", rname);
+ for (n = 0; n < 2; n++)
+ printk(KERN_CONT "%08x ", regs[n]);
+ printk(KERN_CONT "\n");
+}
+
+
+/*
+ * e1000e_dump - Print registers, tx-ring and rx-ring
+ */
+static void e1000e_dump(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_reg_info *reginfo;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_tx_desc *tx_desc;
+ struct my_u0 { u64 a; u64 b; } *u0;
+ struct e1000_buffer *buffer_info;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ union e1000_rx_desc_packet_split *rx_desc_ps;
+ struct e1000_rx_desc *rx_desc;
+ struct my_u1 { u64 a; u64 b; u64 c; u64 d; } *u1;
+ u32 staterr;
+ int i = 0;
+
+ if (!netif_msg_hw(adapter))
+ return;
+
+ /* Print netdevice Info */
+ if (netdev) {
+ dev_info(&adapter->pdev->dev, "Net device Info\n");
+ printk(KERN_INFO "Device Name state "
+ "trans_start last_rx\n");
+ printk(KERN_INFO "%-15s %016lX %016lX %016lX\n",
+ netdev->name,
+ netdev->state,
+ netdev->trans_start,
+ netdev->last_rx);
+ }
+
+ /* Print Registers */
+ dev_info(&adapter->pdev->dev, "Register Dump\n");
+ printk(KERN_INFO " Register Name Value\n");
+ for (reginfo = (struct e1000_reg_info *)e1000_reg_info_tbl;
+ reginfo->name; reginfo++) {
+ e1000_regdump(hw, reginfo);
+ }
+
+ /* Print TX Ring Summary */
+ if (!netdev || !netif_running(netdev))
+ goto exit;
+
+ dev_info(&adapter->pdev->dev, "TX Rings Summary\n");
+ printk(KERN_INFO "Queue [NTU] [NTC] [bi(ntc)->dma ]"
+ " leng ntw timestamp\n");
+ buffer_info = &tx_ring->buffer_info[tx_ring->next_to_clean];
+ printk(KERN_INFO " %5d %5X %5X %016llX %04X %3X %016llX\n",
+ 0, tx_ring->next_to_use, tx_ring->next_to_clean,
+ (u64)buffer_info->dma,
+ buffer_info->length,
+ buffer_info->next_to_watch,
+ (u64)buffer_info->time_stamp);
+
+ /* Print TX Rings */
+ if (!netif_msg_tx_done(adapter))
+ goto rx_ring_summary;
+
+ dev_info(&adapter->pdev->dev, "TX Rings Dump\n");
+
+ /* Transmit Descriptor Formats - DEXT[29] is 0 (Legacy) or 1 (Extended)
+ *
+ * Legacy Transmit Descriptor
+ * +--------------------------------------------------------------+
+ * 0 | Buffer Address [63:0] (Reserved on Write Back) |
+ * +--------------------------------------------------------------+
+ * 8 | Special | CSS | Status | CMD | CSO | Length |
+ * +--------------------------------------------------------------+
+ * 63 48 47 36 35 32 31 24 23 16 15 0
+ *
+ * Extended Context Descriptor (DTYP=0x0) for TSO or checksum offload
+ * 63 48 47 40 39 32 31 16 15 8 7 0
+ * +----------------------------------------------------------------+
+ * 0 | TUCSE | TUCS0 | TUCSS | IPCSE | IPCS0 | IPCSS |
+ * +----------------------------------------------------------------+
+ * 8 | MSS | HDRLEN | RSV | STA | TUCMD | DTYP | PAYLEN |
+ * +----------------------------------------------------------------+
+ * 63 48 47 40 39 36 35 32 31 24 23 20 19 0
+ *
+ * Extended Data Descriptor (DTYP=0x1)
+ * +----------------------------------------------------------------+
+ * 0 | Buffer Address [63:0] |
+ * +----------------------------------------------------------------+
+ * 8 | VLAN tag | POPTS | Rsvd | Status | Command | DTYP | DTALEN |
+ * +----------------------------------------------------------------+
+ * 63 48 47 40 39 36 35 32 31 24 23 20 19 0
+ */
+ printk(KERN_INFO "Tl[desc] [address 63:0 ] [SpeCssSCmCsLen]"
+ " [bi->dma ] leng ntw timestamp bi->skb "
+ "<-- Legacy format\n");
+ printk(KERN_INFO "Tc[desc] [Ce CoCsIpceCoS] [MssHlRSCm0Plen]"
+ " [bi->dma ] leng ntw timestamp bi->skb "
+ "<-- Ext Context format\n");
+ printk(KERN_INFO "Td[desc] [address 63:0 ] [VlaPoRSCm1Dlen]"
+ " [bi->dma ] leng ntw timestamp bi->skb "
+ "<-- Ext Data format\n");
+ for (i = 0; tx_ring->desc && (i < tx_ring->count); i++) {
+ tx_desc = E1000_TX_DESC(*tx_ring, i);
+ buffer_info = &tx_ring->buffer_info[i];
+ u0 = (struct my_u0 *)tx_desc;
+ printk(KERN_INFO "T%c[0x%03X] %016llX %016llX %016llX "
+ "%04X %3X %016llX %p",
+ (!(le64_to_cpu(u0->b) & (1<<29)) ? 'l' :
+ ((le64_to_cpu(u0->b) & (1<<20)) ? 'd' : 'c')), i,
+ le64_to_cpu(u0->a), le64_to_cpu(u0->b),
+ (u64)buffer_info->dma, buffer_info->length,
+ buffer_info->next_to_watch, (u64)buffer_info->time_stamp,
+ buffer_info->skb);
+ if (i == tx_ring->next_to_use && i == tx_ring->next_to_clean)
+ printk(KERN_CONT " NTC/U\n");
+ else if (i == tx_ring->next_to_use)
+ printk(KERN_CONT " NTU\n");
+ else if (i == tx_ring->next_to_clean)
+ printk(KERN_CONT " NTC\n");
+ else
+ printk(KERN_CONT "\n");
+
+ if (netif_msg_pktdata(adapter) && buffer_info->dma != 0)
+ print_hex_dump(KERN_INFO, "", DUMP_PREFIX_ADDRESS,
+ 16, 1, phys_to_virt(buffer_info->dma),
+ buffer_info->length, true);
+ }
+
+ /* Print RX Rings Summary */
+rx_ring_summary:
+ dev_info(&adapter->pdev->dev, "RX Rings Summary\n");
+ printk(KERN_INFO "Queue [NTU] [NTC]\n");
+ printk(KERN_INFO " %5d %5X %5X\n", 0,
+ rx_ring->next_to_use, rx_ring->next_to_clean);
+
+ /* Print RX Rings */
+ if (!netif_msg_rx_status(adapter))
+ goto exit;
+
+ dev_info(&adapter->pdev->dev, "RX Rings Dump\n");
+ switch (adapter->rx_ps_pages) {
+ case 1:
+ case 2:
+ case 3:
+ /* [Extended] Packet Split Receive Descriptor Format
+ *
+ * +-----------------------------------------------------+
+ * 0 | Buffer Address 0 [63:0] |
+ * +-----------------------------------------------------+
+ * 8 | Buffer Address 1 [63:0] |
+ * +-----------------------------------------------------+
+ * 16 | Buffer Address 2 [63:0] |
+ * +-----------------------------------------------------+
+ * 24 | Buffer Address 3 [63:0] |
+ * +-----------------------------------------------------+
+ */
+ printk(KERN_INFO "R [desc] [buffer 0 63:0 ] "
+ "[buffer 1 63:0 ] "
+ "[buffer 2 63:0 ] [buffer 3 63:0 ] [bi->dma ] "
+ "[bi->skb] <-- Ext Pkt Split format\n");
+ /* [Extended] Receive Descriptor (Write-Back) Format
+ *
+ * 63 48 47 32 31 13 12 8 7 4 3 0
+ * +------------------------------------------------------+
+ * 0 | Packet | IP | Rsvd | MRQ | Rsvd | MRQ RSS |
+ * | Checksum | Ident | | Queue | | Type |
+ * +------------------------------------------------------+
+ * 8 | VLAN Tag | Length | Extended Error | Extended Status |
+ * +------------------------------------------------------+
+ * 63 48 47 32 31 20 19 0
+ */
+ printk(KERN_INFO "RWB[desc] [ck ipid mrqhsh] "
+ "[vl l0 ee es] "
+ "[ l3 l2 l1 hs] [reserved ] ---------------- "
+ "[bi->skb] <-- Ext Rx Write-Back format\n");
+ for (i = 0; i < rx_ring->count; i++) {
+ buffer_info = &rx_ring->buffer_info[i];
+ rx_desc_ps = E1000_RX_DESC_PS(*rx_ring, i);
+ u1 = (struct my_u1 *)rx_desc_ps;
+ staterr =
+ le32_to_cpu(rx_desc_ps->wb.middle.status_error);
+ if (staterr & E1000_RXD_STAT_DD) {
+ /* Descriptor Done */
+ printk(KERN_INFO "RWB[0x%03X] %016llX "
+ "%016llX %016llX %016llX "
+ "---------------- %p", i,
+ le64_to_cpu(u1->a),
+ le64_to_cpu(u1->b),
+ le64_to_cpu(u1->c),
+ le64_to_cpu(u1->d),
+ buffer_info->skb);
+ } else {
+ printk(KERN_INFO "R [0x%03X] %016llX "
+ "%016llX %016llX %016llX %016llX %p", i,
+ le64_to_cpu(u1->a),
+ le64_to_cpu(u1->b),
+ le64_to_cpu(u1->c),
+ le64_to_cpu(u1->d),
+ (u64)buffer_info->dma,
+ buffer_info->skb);
+
+ if (netif_msg_pktdata(adapter))
+ print_hex_dump(KERN_INFO, "",
+ DUMP_PREFIX_ADDRESS, 16, 1,
+ phys_to_virt(buffer_info->dma),
+ adapter->rx_ps_bsize0, true);
+ }
+
+ if (i == rx_ring->next_to_use)
+ printk(KERN_CONT " NTU\n");
+ else if (i == rx_ring->next_to_clean)
+ printk(KERN_CONT " NTC\n");
+ else
+ printk(KERN_CONT "\n");
+ }
+ break;
+ default:
+ case 0:
+ /* Legacy Receive Descriptor Format
+ *
+ * +-----------------------------------------------------+
+ * | Buffer Address [63:0] |
+ * +-----------------------------------------------------+
+ * | VLAN Tag | Errors | Status 0 | Packet csum | Length |
+ * +-----------------------------------------------------+
+ * 63 48 47 40 39 32 31 16 15 0
+ */
+ printk(KERN_INFO "Rl[desc] [address 63:0 ] "
+ "[vl er S cks ln] [bi->dma ] [bi->skb] "
+ "<-- Legacy format\n");
+ for (i = 0; rx_ring->desc && (i < rx_ring->count); i++) {
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ buffer_info = &rx_ring->buffer_info[i];
+ u0 = (struct my_u0 *)rx_desc;
+ printk(KERN_INFO "Rl[0x%03X] %016llX %016llX "
+ "%016llX %p",
+ i, le64_to_cpu(u0->a), le64_to_cpu(u0->b),
+ (u64)buffer_info->dma, buffer_info->skb);
+ if (i == rx_ring->next_to_use)
+ printk(KERN_CONT " NTU\n");
+ else if (i == rx_ring->next_to_clean)
+ printk(KERN_CONT " NTC\n");
+ else
+ printk(KERN_CONT "\n");
+
+ if (netif_msg_pktdata(adapter))
+ print_hex_dump(KERN_INFO, "",
+ DUMP_PREFIX_ADDRESS,
+ 16, 1, phys_to_virt(buffer_info->dma),
+ adapter->rx_buffer_len, true);
+ }
+ }
+
+exit:
+ return;
+}
+
+/**
+ * e1000_desc_unused - calculate if we have unused descriptors
+ **/
+static int e1000_desc_unused(struct e1000_ring *ring)
+{
+ if (ring->next_to_clean > ring->next_to_use)
+ return ring->next_to_clean - ring->next_to_use - 1;
+
+ return ring->count + ring->next_to_clean - ring->next_to_use - 1;
+}
+
+/**
+ * e1000_receive_skb - helper function to handle Rx indications
+ * @adapter: board private structure
+ * @status: descriptor status field as written by hardware
+ * @vlan: descriptor vlan field as written by hardware (no le/be conversion)
+ * @skb: pointer to sk_buff to be indicated to stack
+ **/
+static void e1000_receive_skb(struct e1000_adapter *adapter,
+ struct net_device *netdev,
+ struct sk_buff *skb,
+ u8 status, __le16 vlan)
+{
+ skb->protocol = eth_type_trans(skb, netdev);
+
+ if (adapter->vlgrp && (status & E1000_RXD_STAT_VP))
+ vlan_gro_receive(&adapter->napi, adapter->vlgrp,
+ le16_to_cpu(vlan), skb);
+ else
+ napi_gro_receive(&adapter->napi, skb);
+}
+
+/**
+ * e1000_rx_checksum - Receive Checksum Offload for 82543
+ * @adapter: board private structure
+ * @status_err: receive descriptor status and error fields
+ * @csum: receive descriptor csum field
+ * @sk_buff: socket buffer with received data
+ **/
+static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
+ u32 csum, struct sk_buff *skb)
+{
+ u16 status = (u16)status_err;
+ u8 errors = (u8)(status_err >> 24);
+ skb->ip_summed = CHECKSUM_NONE;
+
+ /* Ignore Checksum bit is set */
+ if (status & E1000_RXD_STAT_IXSM)
+ return;
+ /* TCP/UDP checksum error bit is set */
+ if (errors & E1000_RXD_ERR_TCPE) {
+ /* let the stack verify checksum errors */
+ adapter->hw_csum_err++;
+ return;
+ }
+
+ /* TCP/UDP Checksum has not been calculated */
+ if (!(status & (E1000_RXD_STAT_TCPCS | E1000_RXD_STAT_UDPCS)))
+ return;
+
+ /* It must be a TCP or UDP packet with a valid checksum */
+ if (status & E1000_RXD_STAT_TCPCS) {
+ /* TCP checksum is good */
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+ } else {
+ /*
+ * IP fragment with UDP payload
+ * Hardware complements the payload checksum, so we undo it
+ * and then put the value in host order for further stack use.
+ */
+ __sum16 sum = (__force __sum16)htons(csum);
+ skb->csum = csum_unfold(~sum);
+ skb->ip_summed = CHECKSUM_COMPLETE;
+ }
+ adapter->hw_csum_good++;
+}
+
+/**
+ * e1000_alloc_rx_buffers - Replace used receive buffers; legacy & extended
+ * @adapter: address of board private structure
+ **/
+static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
+ int cleaned_count)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_rx_desc *rx_desc;
+ struct e1000_buffer *buffer_info;
+ struct sk_buff *skb;
+ unsigned int i;
+ unsigned int bufsz = adapter->rx_buffer_len;
+
+ i = rx_ring->next_to_use;
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (cleaned_count--) {
+ skb = buffer_info->skb;
+ if (skb) {
+ skb_trim(skb, 0);
+ goto map_skb;
+ }
+
+ skb = netdev_alloc_skb_ip_align(netdev, bufsz);
+ if (!skb) {
+ /* Better luck next round */
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ buffer_info->skb = skb;
+map_skb:
+ buffer_info->dma = dma_map_single(&pdev->dev, skb->data,
+ adapter->rx_buffer_len,
+ DMA_FROM_DEVICE);
+ if (dma_mapping_error(&pdev->dev, buffer_info->dma)) {
+ dev_err(&pdev->dev, "RX DMA map failed\n");
+ adapter->rx_dma_failed++;
+ break;
+ }
+
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+
+ if (unlikely(!(i & (E1000_RX_BUFFER_WRITE - 1)))) {
+ /*
+ * Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64).
+ */
+ wmb();
+ writel(i, adapter->hw.hw_addr + rx_ring->tail);
+ }
+ i++;
+ if (i == rx_ring->count)
+ i = 0;
+ buffer_info = &rx_ring->buffer_info[i];
+ }
+
+ rx_ring->next_to_use = i;
+}
+
+/**
+ * e1000_alloc_rx_buffers_ps - Replace used receive buffers; packet split
+ * @adapter: address of board private structure
+ **/
+static void e1000_alloc_rx_buffers_ps(struct e1000_adapter *adapter,
+ int cleaned_count)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ union e1000_rx_desc_packet_split *rx_desc;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_buffer *buffer_info;
+ struct e1000_ps_page *ps_page;
+ struct sk_buff *skb;
+ unsigned int i, j;
+
+ i = rx_ring->next_to_use;
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (cleaned_count--) {
+ rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
+
+ for (j = 0; j < PS_PAGE_BUFFERS; j++) {
+ ps_page = &buffer_info->ps_pages[j];
+ if (j >= adapter->rx_ps_pages) {
+ /* all unused desc entries get hw null ptr */
+ rx_desc->read.buffer_addr[j+1] = ~cpu_to_le64(0);
+ continue;
+ }
+ if (!ps_page->page) {
+ ps_page->page = alloc_page(GFP_ATOMIC);
+ if (!ps_page->page) {
+ adapter->alloc_rx_buff_failed++;
+ goto no_buffers;
+ }
+ ps_page->dma = dma_map_page(&pdev->dev,
+ ps_page->page,
+ 0, PAGE_SIZE,
+ DMA_FROM_DEVICE);
+ if (dma_mapping_error(&pdev->dev,
+ ps_page->dma)) {
+ dev_err(&adapter->pdev->dev,
+ "RX DMA page map failed\n");
+ adapter->rx_dma_failed++;
+ goto no_buffers;
+ }
+ }
+ /*
+ * Refresh the desc even if buffer_addrs
+ * didn't change because each write-back
+ * erases this info.
+ */
+ rx_desc->read.buffer_addr[j+1] =
+ cpu_to_le64(ps_page->dma);
+ }
+
+ skb = netdev_alloc_skb_ip_align(netdev,
+ adapter->rx_ps_bsize0);
+
+ if (!skb) {
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ buffer_info->skb = skb;
+ buffer_info->dma = dma_map_single(&pdev->dev, skb->data,
+ adapter->rx_ps_bsize0,
+ DMA_FROM_DEVICE);
+ if (dma_mapping_error(&pdev->dev, buffer_info->dma)) {
+ dev_err(&pdev->dev, "RX DMA map failed\n");
+ adapter->rx_dma_failed++;
+ /* cleanup skb */
+ dev_kfree_skb_any(skb);
+ buffer_info->skb = NULL;
+ break;
+ }
+
+ rx_desc->read.buffer_addr[0] = cpu_to_le64(buffer_info->dma);
+
+ if (unlikely(!(i & (E1000_RX_BUFFER_WRITE - 1)))) {
+ /*
+ * Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64).
+ */
+ wmb();
+ writel(i<<1, adapter->hw.hw_addr + rx_ring->tail);
+ }
+
+ i++;
+ if (i == rx_ring->count)
+ i = 0;
+ buffer_info = &rx_ring->buffer_info[i];
+ }
+
+no_buffers:
+ rx_ring->next_to_use = i;
+}
+
+/**
+ * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers
+ * @adapter: address of board private structure
+ * @cleaned_count: number of buffers to allocate this pass
+ **/
+
+static void e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
+ int cleaned_count)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_rx_desc *rx_desc;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_buffer *buffer_info;
+ struct sk_buff *skb;
+ unsigned int i;
+ unsigned int bufsz = 256 - 16 /* for skb_reserve */;
+
+ i = rx_ring->next_to_use;
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (cleaned_count--) {
+ skb = buffer_info->skb;
+ if (skb) {
+ skb_trim(skb, 0);
+ goto check_page;
+ }
+
+ skb = netdev_alloc_skb_ip_align(netdev, bufsz);
+ if (unlikely(!skb)) {
+ /* Better luck next round */
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ buffer_info->skb = skb;
+check_page:
+ /* allocate a new page if necessary */
+ if (!buffer_info->page) {
+ buffer_info->page = alloc_page(GFP_ATOMIC);
+ if (unlikely(!buffer_info->page)) {
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+ }
+
+ if (!buffer_info->dma)
+ buffer_info->dma = dma_map_page(&pdev->dev,
+ buffer_info->page, 0,
+ PAGE_SIZE,
+ DMA_FROM_DEVICE);
+
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+
+ if (unlikely(++i == rx_ring->count))
+ i = 0;
+ buffer_info = &rx_ring->buffer_info[i];
+ }
+
+ if (likely(rx_ring->next_to_use != i)) {
+ rx_ring->next_to_use = i;
+ if (unlikely(i-- == 0))
+ i = (rx_ring->count - 1);
+
+ /* Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64). */
+ wmb();
+ writel(i, adapter->hw.hw_addr + rx_ring->tail);
+ }
+}
+
+/**
+ * e1000_clean_rx_irq - Send received data up the network stack; legacy
+ * @adapter: board private structure
+ *
+ * the return value indicates whether actual cleaning was done, there
+ * is no guarantee that everything was cleaned
+ **/
+static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
+ int *work_done, int work_to_do)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_rx_desc *rx_desc, *next_rxd;
+ struct e1000_buffer *buffer_info, *next_buffer;
+ u32 length;
+ unsigned int i;
+ int cleaned_count = 0;
+ bool cleaned = 0;
+ unsigned int total_rx_bytes = 0, total_rx_packets = 0;
+
+ i = rx_ring->next_to_clean;
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (rx_desc->status & E1000_RXD_STAT_DD) {
+ struct sk_buff *skb;
+ u8 status;
+
+ if (*work_done >= work_to_do)
+ break;
+ (*work_done)++;
+ rmb(); /* read descriptor and rx_buffer_info after status DD */
+
+ status = rx_desc->status;
+ skb = buffer_info->skb;
+
+ if (!adapter->ecdev)
+ buffer_info->skb = NULL;
+
+ prefetch(skb->data - NET_IP_ALIGN);
+
+ i++;
+ if (i == rx_ring->count)
+ i = 0;
+ next_rxd = E1000_RX_DESC(*rx_ring, i);
+ prefetch(next_rxd);
+
+ next_buffer = &rx_ring->buffer_info[i];
+
+ cleaned = 1;
+ cleaned_count++;
+ dma_unmap_single(&pdev->dev,
+ buffer_info->dma,
+ adapter->rx_buffer_len,
+ DMA_FROM_DEVICE);
+ buffer_info->dma = 0;
+
+ length = le16_to_cpu(rx_desc->length);
+
+ /*
+ * !EOP means multiple descriptors were used to store a single
+ * packet, if that's the case we need to toss it. In fact, we
+ * need to toss every packet with the EOP bit clear and the
+ * next frame that _does_ have the EOP bit set, as it is by
+ * definition only a frame fragment
+ */
+ if (unlikely(!(status & E1000_RXD_STAT_EOP)))
+ adapter->flags2 |= FLAG2_IS_DISCARDING;
+
+ if (adapter->flags2 & FLAG2_IS_DISCARDING) {
+ /* All receives must fit into a single buffer */
+ e_dbg("Receive packet consumed multiple buffers\n");
+ /* recycle */
+ buffer_info->skb = skb;
+ if (status & E1000_RXD_STAT_EOP)
+ adapter->flags2 &= ~FLAG2_IS_DISCARDING;
+ goto next_desc;
+ }
+
+ if (!adapter->ecdev && (rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK)) {
+ /* recycle */
+ buffer_info->skb = skb;
+ goto next_desc;
+ }
+
+ /* adjust length to remove Ethernet CRC */
+ if (!(adapter->flags2 & FLAG2_CRC_STRIPPING))
+ length -= 4;
+
+ total_rx_bytes += length;
+ total_rx_packets++;
+
+ /*
+ * code added for copybreak, this should improve
+ * performance for small packets with large amounts
+ * of reassembly being done in the stack
+ */
+ if (!adapter->ecdev && length < copybreak) {
+ struct sk_buff *new_skb =
+ netdev_alloc_skb_ip_align(netdev, length);
+ if (new_skb) {
+ skb_copy_to_linear_data_offset(new_skb,
+ -NET_IP_ALIGN,
+ (skb->data -
+ NET_IP_ALIGN),
+ (length +
+ NET_IP_ALIGN));
+ /* save the skb in buffer_info as good */
+ buffer_info->skb = skb;
+ skb = new_skb;
+ }
+ /* else just continue with the old one */
+ }
+ /* end copybreak code */
+ skb_put(skb, length);
+
+ /* Receive Checksum Offload */
+ e1000_rx_checksum(adapter,
+ (u32)(status) |
+ ((u32)(rx_desc->errors) << 24),
+ le16_to_cpu(rx_desc->csum), skb);
+
+ if (adapter->ecdev) {
+ ecdev_receive(adapter->ecdev, skb->data, length);
+ adapter->ec_watchdog_jiffies = jiffies;
+ } else {
+ e1000_receive_skb(adapter, netdev, skb,status,rx_desc->special);
+ }
+
+next_desc:
+ rx_desc->status = 0;
+
+ /* return some buffers to hardware, one at a time is too slow */
+ if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+ cleaned_count = 0;
+ }
+
+ /* use prefetched values */
+ rx_desc = next_rxd;
+ buffer_info = next_buffer;
+ }
+ rx_ring->next_to_clean = i;
+
+ cleaned_count = e1000_desc_unused(rx_ring);
+ if (cleaned_count)
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+
+ adapter->total_rx_bytes += total_rx_bytes;
+ adapter->total_rx_packets += total_rx_packets;
+ netdev->stats.rx_bytes += total_rx_bytes;
+ netdev->stats.rx_packets += total_rx_packets;
+ return cleaned;
+}
+
+static void e1000_put_txbuf(struct e1000_adapter *adapter,
+ struct e1000_buffer *buffer_info)
+{
+ if (adapter->ecdev)
+ return;
+
+ if (buffer_info->dma) {
+ if (buffer_info->mapped_as_page)
+ dma_unmap_page(&adapter->pdev->dev, buffer_info->dma,
+ buffer_info->length, DMA_TO_DEVICE);
+ else
+ dma_unmap_single(&adapter->pdev->dev, buffer_info->dma,
+ buffer_info->length, DMA_TO_DEVICE);
+ buffer_info->dma = 0;
+ }
+ if (buffer_info->skb) {
+ dev_kfree_skb_any(buffer_info->skb);
+ buffer_info->skb = NULL;
+ }
+ buffer_info->time_stamp = 0;
+}
+
+static void e1000_print_hw_hang(struct work_struct *work)
+{
+ struct e1000_adapter *adapter = container_of(work,
+ struct e1000_adapter,
+ print_hang_task);
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ unsigned int i = tx_ring->next_to_clean;
+ unsigned int eop = tx_ring->buffer_info[i].next_to_watch;
+ struct e1000_tx_desc *eop_desc = E1000_TX_DESC(*tx_ring, eop);
+ struct e1000_hw *hw = &adapter->hw;
+ u16 phy_status, phy_1000t_status, phy_ext_status;
+ u16 pci_status;
+
+ e1e_rphy(hw, PHY_STATUS, &phy_status);
+ e1e_rphy(hw, PHY_1000T_STATUS, &phy_1000t_status);
+ e1e_rphy(hw, PHY_EXT_STATUS, &phy_ext_status);
+
+ pci_read_config_word(adapter->pdev, PCI_STATUS, &pci_status);
+
+ /* detected Hardware unit hang */
+ e_err("Detected Hardware Unit Hang:\n"
+ " TDH <%x>\n"
+ " TDT <%x>\n"
+ " next_to_use <%x>\n"
+ " next_to_clean <%x>\n"
+ "buffer_info[next_to_clean]:\n"
+ " time_stamp <%lx>\n"
+ " next_to_watch <%x>\n"
+ " jiffies <%lx>\n"
+ " next_to_watch.status <%x>\n"
+ "MAC Status <%x>\n"
+ "PHY Status <%x>\n"
+ "PHY 1000BASE-T Status <%x>\n"
+ "PHY Extended Status <%x>\n"
+ "PCI Status <%x>\n",
+ readl(adapter->hw.hw_addr + tx_ring->head),
+ readl(adapter->hw.hw_addr + tx_ring->tail),
+ tx_ring->next_to_use,
+ tx_ring->next_to_clean,
+ tx_ring->buffer_info[eop].time_stamp,
+ eop,
+ jiffies,
+ eop_desc->upper.fields.status,
+ er32(STATUS),
+ phy_status,
+ phy_1000t_status,
+ phy_ext_status,
+ pci_status);
+}
+
+/**
+ * e1000_clean_tx_irq - Reclaim resources after transmit completes
+ * @adapter: board private structure
+ *
+ * the return value indicates whether actual cleaning was done, there
+ * is no guarantee that everything was cleaned
+ **/
+static bool e1000_clean_tx_irq(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_tx_desc *tx_desc, *eop_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i, eop;
+ unsigned int count = 0;
+ unsigned int total_tx_bytes = 0, total_tx_packets = 0;
+
+ i = tx_ring->next_to_clean;
+ eop = tx_ring->buffer_info[i].next_to_watch;
+ eop_desc = E1000_TX_DESC(*tx_ring, eop);
+
+ while ((eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) &&
+ (count < tx_ring->count)) {
+ bool cleaned = false;
+ rmb(); /* read buffer_info after eop_desc */
+ for (; !cleaned; count++) {
+ tx_desc = E1000_TX_DESC(*tx_ring, i);
+ buffer_info = &tx_ring->buffer_info[i];
+ cleaned = (i == eop);
+
+ if (cleaned) {
+ total_tx_packets += buffer_info->segs;
+ total_tx_bytes += buffer_info->bytecount;
+ }
+
+ e1000_put_txbuf(adapter, buffer_info);
+ tx_desc->upper.data = 0;
+
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+ }
+
+ if (i == tx_ring->next_to_use)
+ break;
+ eop = tx_ring->buffer_info[i].next_to_watch;
+ eop_desc = E1000_TX_DESC(*tx_ring, eop);
+ }
+
+ tx_ring->next_to_clean = i;
+
+#define TX_WAKE_THRESHOLD 32
+ if (!adapter->ecdev && count && netif_carrier_ok(netdev) &&
+ e1000_desc_unused(tx_ring) >= TX_WAKE_THRESHOLD) {
+ /* Make sure that anybody stopping the queue after this
+ * sees the new next_to_clean.
+ */
+ smp_mb();
+
+ if (netif_queue_stopped(netdev) &&
+ !(test_bit(__E1000_DOWN, &adapter->state))) {
+ netif_wake_queue(netdev);
+ ++adapter->restart_queue;
+ }
+ }
+
+ if (!adapter->ecdev && adapter->detect_tx_hung) {
+ /*
+ * Detect a transmit hang in hardware, this serializes the
+ * check with the clearing of time_stamp and movement of i
+ */
+ adapter->detect_tx_hung = 0;
+ if (tx_ring->buffer_info[i].time_stamp &&
+ time_after(jiffies, tx_ring->buffer_info[i].time_stamp
+ + (adapter->tx_timeout_factor * HZ)) &&
+ !(er32(STATUS) & E1000_STATUS_TXOFF)) {
+ schedule_work(&adapter->print_hang_task);
+ netif_stop_queue(netdev);
+ }
+ }
+ adapter->total_tx_bytes += total_tx_bytes;
+ adapter->total_tx_packets += total_tx_packets;
+ netdev->stats.tx_bytes += total_tx_bytes;
+ netdev->stats.tx_packets += total_tx_packets;
+ return (count < tx_ring->count);
+}
+
+/**
+ * e1000_clean_rx_irq_ps - Send received data up the network stack; packet split
+ * @adapter: board private structure
+ *
+ * the return value indicates whether actual cleaning was done, there
+ * is no guarantee that everything was cleaned
+ **/
+static bool e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
+ int *work_done, int work_to_do)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ union e1000_rx_desc_packet_split *rx_desc, *next_rxd;
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_buffer *buffer_info, *next_buffer;
+ struct e1000_ps_page *ps_page;
+ struct sk_buff *skb;
+ unsigned int i, j;
+ u32 length, staterr;
+ int cleaned_count = 0;
+ bool cleaned = 0;
+ unsigned int total_rx_bytes = 0, total_rx_packets = 0;
+
+ i = rx_ring->next_to_clean;
+ rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
+ staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (staterr & E1000_RXD_STAT_DD) {
+ if (*work_done >= work_to_do)
+ break;
+ (*work_done)++;
+ skb = buffer_info->skb;
+ rmb(); /* read descriptor and rx_buffer_info after status DD */
+
+ /* in the packet split case this is header only */
+ prefetch(skb->data - NET_IP_ALIGN);
+
+ i++;
+ if (i == rx_ring->count)
+ i = 0;
+ next_rxd = E1000_RX_DESC_PS(*rx_ring, i);
+ prefetch(next_rxd);
+
+ next_buffer = &rx_ring->buffer_info[i];
+
+ cleaned = 1;
+ cleaned_count++;
+ dma_unmap_single(&pdev->dev, buffer_info->dma,
+ adapter->rx_ps_bsize0,
+ DMA_FROM_DEVICE);
+ buffer_info->dma = 0;
+
+ /* see !EOP comment in other rx routine */
+ if (!(staterr & E1000_RXD_STAT_EOP))
+ adapter->flags2 |= FLAG2_IS_DISCARDING;
+
+ if (adapter->flags2 & FLAG2_IS_DISCARDING) {
+ e_dbg("Packet Split buffers didn't pick up the full "
+ "packet\n");
+ if (!adapter->ecdev) dev_kfree_skb_irq(skb);
+ if (staterr & E1000_RXD_STAT_EOP)
+ adapter->flags2 &= ~FLAG2_IS_DISCARDING;
+ goto next_desc;
+ }
+
+ if (staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) {
+ if (!adapter->ecdev)
+ dev_kfree_skb_irq(skb);
+ goto next_desc;
+ }
+
+ length = le16_to_cpu(rx_desc->wb.middle.length0);
+
+ if (!length) {
+ e_dbg("Last part of the packet spanning multiple "
+ "descriptors\n");
+ if (!adapter->ecdev)
+ dev_kfree_skb_irq(skb);
+ goto next_desc;
+ }
+
+ /* Good Receive */
+ skb_put(skb, length);
+
+ {
+ /*
+ * this looks ugly, but it seems compiler issues make it
+ * more efficient than reusing j
+ */
+ int l1 = le16_to_cpu(rx_desc->wb.upper.length[0]);
+
+ /*
+ * page alloc/put takes too long and effects small packet
+ * throughput, so unsplit small packets and save the alloc/put
+ * only valid in softirq (napi) context to call kmap_*
+ */
+ if (l1 && (l1 <= copybreak) &&
+ ((length + l1) <= adapter->rx_ps_bsize0)) {
+ u8 *vaddr;
+
+ ps_page = &buffer_info->ps_pages[0];
+
+ /*
+ * there is no documentation about how to call
+ * kmap_atomic, so we can't hold the mapping
+ * very long
+ */
+ dma_sync_single_for_cpu(&pdev->dev, ps_page->dma,
+ PAGE_SIZE, DMA_FROM_DEVICE);
+ vaddr = kmap_atomic(ps_page->page, KM_SKB_DATA_SOFTIRQ);
+ memcpy(skb_tail_pointer(skb), vaddr, l1);
+ kunmap_atomic(vaddr, KM_SKB_DATA_SOFTIRQ);
+ dma_sync_single_for_device(&pdev->dev, ps_page->dma,
+ PAGE_SIZE, DMA_FROM_DEVICE);
+
+ /* remove the CRC */
+ if (!(adapter->flags2 & FLAG2_CRC_STRIPPING))
+ l1 -= 4;
+
+ skb_put(skb, l1);
+ goto copydone;
+ } /* if */
+ }
+
+ for (j = 0; j < PS_PAGE_BUFFERS; j++) {
+ length = le16_to_cpu(rx_desc->wb.upper.length[j]);
+ if (!length)
+ break;
+
+ ps_page = &buffer_info->ps_pages[j];
+ dma_unmap_page(&pdev->dev, ps_page->dma, PAGE_SIZE,
+ DMA_FROM_DEVICE);
+ ps_page->dma = 0;
+ skb_fill_page_desc(skb, j, ps_page->page, 0, length);
+ ps_page->page = NULL;
+ skb->len += length;
+ skb->data_len += length;
+ skb->truesize += length;
+ }
+
+ /* strip the ethernet crc, problem is we're using pages now so
+ * this whole operation can get a little cpu intensive
+ */
+ if (!(adapter->flags2 & FLAG2_CRC_STRIPPING))
+ pskb_trim(skb, skb->len - 4);
+
+copydone:
+ total_rx_bytes += skb->len;
+ total_rx_packets++;
+
+ e1000_rx_checksum(adapter, staterr, le16_to_cpu(
+ rx_desc->wb.lower.hi_dword.csum_ip.csum), skb);
+
+ if (rx_desc->wb.upper.header_status &
+ cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP))
+ adapter->rx_hdr_split++;
+
+ if (adapter->ecdev) {
+ ecdev_receive(adapter->ecdev, skb->data, length);
+ adapter->ec_watchdog_jiffies = jiffies;
+ } else {
+ e1000_receive_skb(adapter, netdev, skb,
+ staterr, rx_desc->wb.middle.vlan);
+ }
+
+next_desc:
+ rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF);
+ if (!adapter->ecdev) buffer_info->skb = NULL;
+
+ /* return some buffers to hardware, one at a time is too slow */
+ if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+ cleaned_count = 0;
+ }
+
+ /* use prefetched values */
+ rx_desc = next_rxd;
+ buffer_info = next_buffer;
+
+ staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
+ }
+ rx_ring->next_to_clean = i;
+
+ cleaned_count = e1000_desc_unused(rx_ring);
+ if (cleaned_count)
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+
+ adapter->total_rx_bytes += total_rx_bytes;
+ adapter->total_rx_packets += total_rx_packets;
+ netdev->stats.rx_bytes += total_rx_bytes;
+ netdev->stats.rx_packets += total_rx_packets;
+ return cleaned;
+}
+
+/**
+ * e1000_consume_page - helper function
+ **/
+static void e1000_consume_page(struct e1000_buffer *bi, struct sk_buff *skb,
+ u16 length)
+{
+ bi->page = NULL;
+ skb->len += length;
+ skb->data_len += length;
+ skb->truesize += length;
+}
+
+/**
+ * e1000_clean_jumbo_rx_irq - Send received data up the network stack; legacy
+ * @adapter: board private structure
+ *
+ * the return value indicates whether actual cleaning was done, there
+ * is no guarantee that everything was cleaned
+ **/
+
+static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
+ int *work_done, int work_to_do)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_rx_desc *rx_desc, *next_rxd;
+ struct e1000_buffer *buffer_info, *next_buffer;
+ u32 length;
+ unsigned int i;
+ int cleaned_count = 0;
+ bool cleaned = false;
+ unsigned int total_rx_bytes=0, total_rx_packets=0;
+
+ i = rx_ring->next_to_clean;
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (rx_desc->status & E1000_RXD_STAT_DD) {
+ struct sk_buff *skb;
+ u8 status;
+
+ if (*work_done >= work_to_do)
+ break;
+ (*work_done)++;
+ rmb(); /* read descriptor and rx_buffer_info after status DD */
+
+ status = rx_desc->status;
+ skb = buffer_info->skb;
+
+ if (!adapter->ecdev)
+ buffer_info->skb = NULL;
+
+ ++i;
+ if (i == rx_ring->count)
+ i = 0;
+ next_rxd = E1000_RX_DESC(*rx_ring, i);
+ prefetch(next_rxd);
+
+ next_buffer = &rx_ring->buffer_info[i];
+
+ cleaned = true;
+ cleaned_count++;
+ dma_unmap_page(&pdev->dev, buffer_info->dma, PAGE_SIZE,
+ DMA_FROM_DEVICE);
+ buffer_info->dma = 0;
+
+ length = le16_to_cpu(rx_desc->length);
+
+ /* errors is only valid for DD + EOP descriptors */
+ if (!adapter->ecdev && unlikely((status & E1000_RXD_STAT_EOP) &&
+ (rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK))) {
+ /* recycle both page and skb */
+ buffer_info->skb = skb;
+ /* an error means any chain goes out the window
+ * too */
+ if (rx_ring->rx_skb_top)
+ dev_kfree_skb(rx_ring->rx_skb_top);
+ rx_ring->rx_skb_top = NULL;
+ goto next_desc;
+ }
+
+#define rxtop rx_ring->rx_skb_top
+ if (!(status & E1000_RXD_STAT_EOP)) {
+ /* this descriptor is only the beginning (or middle) */
+ if (!rxtop) {
+ /* this is the beginning of a chain */
+ rxtop = skb;
+ skb_fill_page_desc(rxtop, 0, buffer_info->page,
+ 0, length);
+ } else {
+ /* this is the middle of a chain */
+ skb_fill_page_desc(rxtop,
+ skb_shinfo(rxtop)->nr_frags,
+ buffer_info->page, 0, length);
+ /* re-use the skb, only consumed the page */
+ buffer_info->skb = skb;
+ }
+ e1000_consume_page(buffer_info, rxtop, length);
+ goto next_desc;
+ } else {
+ if (rxtop) {
+ /* end of the chain */
+ skb_fill_page_desc(rxtop,
+ skb_shinfo(rxtop)->nr_frags,
+ buffer_info->page, 0, length);
+ /* re-use the current skb, we only consumed the
+ * page */
+ buffer_info->skb = skb;
+ skb = rxtop;
+ rxtop = NULL;
+ e1000_consume_page(buffer_info, skb, length);
+ } else {
+ /* no chain, got EOP, this buf is the packet
+ * copybreak to save the put_page/alloc_page */
+ if (length <= copybreak &&
+ skb_tailroom(skb) >= length) {
+ u8 *vaddr;
+ vaddr = kmap_atomic(buffer_info->page,
+ KM_SKB_DATA_SOFTIRQ);
+ memcpy(skb_tail_pointer(skb), vaddr,
+ length);
+ kunmap_atomic(vaddr,
+ KM_SKB_DATA_SOFTIRQ);
+ /* re-use the page, so don't erase
+ * buffer_info->page */
+ skb_put(skb, length);
+ } else {
+ skb_fill_page_desc(skb, 0,
+ buffer_info->page, 0,
+ length);
+ e1000_consume_page(buffer_info, skb,
+ length);
+ }
+ }
+ }
+
+ /* Receive Checksum Offload XXX recompute due to CRC strip? */
+ e1000_rx_checksum(adapter,
+ (u32)(status) |
+ ((u32)(rx_desc->errors) << 24),
+ le16_to_cpu(rx_desc->csum), skb);
+
+ /* probably a little skewed due to removing CRC */
+ total_rx_bytes += skb->len;
+ total_rx_packets++;
+
+ /* eth type trans needs skb->data to point to something */
+ if (!adapter->ecdev && !pskb_may_pull(skb, ETH_HLEN)) {
+ e_err("pskb_may_pull failed.\n");
+ dev_kfree_skb(skb);
+ goto next_desc;
+ }
+
+ if (adapter->ecdev) {
+ ecdev_receive(adapter->ecdev, skb->data, length);
+ adapter->ec_watchdog_jiffies = jiffies;
+ } else {
+ e1000_receive_skb(adapter, netdev, skb, status,
+ rx_desc->special);
+ }
+
+next_desc:
+ rx_desc->status = 0;
+
+ /* return some buffers to hardware, one at a time is too slow */
+ if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+ cleaned_count = 0;
+ }
+
+ /* use prefetched values */
+ rx_desc = next_rxd;
+ buffer_info = next_buffer;
+ }
+ rx_ring->next_to_clean = i;
+
+ cleaned_count = e1000_desc_unused(rx_ring);
+ if (cleaned_count)
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+
+ adapter->total_rx_bytes += total_rx_bytes;
+ adapter->total_rx_packets += total_rx_packets;
+ netdev->stats.rx_bytes += total_rx_bytes;
+ netdev->stats.rx_packets += total_rx_packets;
+ return cleaned;
+}
+
+/**
+ * e1000_clean_rx_ring - Free Rx Buffers per Queue
+ * @adapter: board private structure
+ **/
+static void e1000_clean_rx_ring(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_buffer *buffer_info;
+ struct e1000_ps_page *ps_page;
+ struct pci_dev *pdev = adapter->pdev;
+ unsigned int i, j;
+
+ /* Free all the Rx ring sk_buffs */
+ for (i = 0; i < rx_ring->count; i++) {
+ buffer_info = &rx_ring->buffer_info[i];
+ if (buffer_info->dma) {
+ if (adapter->clean_rx == e1000_clean_rx_irq)
+ dma_unmap_single(&pdev->dev, buffer_info->dma,
+ adapter->rx_buffer_len,
+ DMA_FROM_DEVICE);
+ else if (adapter->clean_rx == e1000_clean_jumbo_rx_irq)
+ dma_unmap_page(&pdev->dev, buffer_info->dma,
+ PAGE_SIZE,
+ DMA_FROM_DEVICE);
+ else if (adapter->clean_rx == e1000_clean_rx_irq_ps)
+ dma_unmap_single(&pdev->dev, buffer_info->dma,
+ adapter->rx_ps_bsize0,
+ DMA_FROM_DEVICE);
+ buffer_info->dma = 0;
+ }
+
+ if (buffer_info->page) {
+ put_page(buffer_info->page);
+ buffer_info->page = NULL;
+ }
+
+ if (buffer_info->skb) {
+ dev_kfree_skb(buffer_info->skb);
+ buffer_info->skb = NULL;
+ }
+
+ for (j = 0; j < PS_PAGE_BUFFERS; j++) {
+ ps_page = &buffer_info->ps_pages[j];
+ if (!ps_page->page)
+ break;
+ dma_unmap_page(&pdev->dev, ps_page->dma, PAGE_SIZE,
+ DMA_FROM_DEVICE);
+ ps_page->dma = 0;
+ put_page(ps_page->page);
+ ps_page->page = NULL;
+ }
+ }
+
+ /* there also may be some cached data from a chained receive */
+ if (rx_ring->rx_skb_top) {
+ dev_kfree_skb(rx_ring->rx_skb_top);
+ rx_ring->rx_skb_top = NULL;
+ }
+
+ /* Zero out the descriptor ring */
+ memset(rx_ring->desc, 0, rx_ring->size);
+
+ rx_ring->next_to_clean = 0;
+ rx_ring->next_to_use = 0;
+ adapter->flags2 &= ~FLAG2_IS_DISCARDING;
+
+ writel(0, adapter->hw.hw_addr + rx_ring->head);
+ writel(0, adapter->hw.hw_addr + rx_ring->tail);
+}
+
+static void e1000e_downshift_workaround(struct work_struct *work)
+{
+ struct e1000_adapter *adapter = container_of(work,
+ struct e1000_adapter, downshift_task);
+
+ e1000e_gig_downshift_workaround_ich8lan(&adapter->hw);
+}
+
+/**
+ * e1000_intr_msi - Interrupt Handler
+ * @irq: interrupt number
+ * @data: pointer to a network interface device structure
+ **/
+static irqreturn_t e1000_intr_msi(int irq, void *data)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 icr = er32(ICR);
+
+ if (adapter->ecdev) {
+ int ec_work_done = 0;
+ adapter->clean_rx(adapter, &ec_work_done, 100);
+ e1000_clean_tx_irq(adapter);
+ return IRQ_HANDLED;
+ }
+ /*
+ * read ICR disables interrupts using IAM
+ */
+
+ if (icr & E1000_ICR_LSC) {
+ hw->mac.get_link_status = 1;
+ /*
+ * ICH8 workaround-- Call gig speed drop workaround on cable
+ * disconnect (LSC) before accessing any PHY registers
+ */
+ if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) &&
+ (!(er32(STATUS) & E1000_STATUS_LU)))
+ schedule_work(&adapter->downshift_task);
+
+ /*
+ * 80003ES2LAN workaround-- For packet buffer work-around on
+ * link down event; disable receives here in the ISR and reset
+ * adapter in watchdog
+ */
+ if (netif_carrier_ok(netdev) &&
+ adapter->flags & FLAG_RX_NEEDS_RESTART) {
+ /* disable receives */
+ u32 rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ adapter->flags |= FLAG_RX_RESTART_NOW;
+ }
+ /* guard against interrupt when we're going down */
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->watchdog_timer, jiffies + 1);
+ }
+
+ if (napi_schedule_prep(&adapter->napi)) {
+ adapter->total_tx_bytes = 0;
+ adapter->total_tx_packets = 0;
+ adapter->total_rx_bytes = 0;
+ adapter->total_rx_packets = 0;
+ __napi_schedule(&adapter->napi);
+ }
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * e1000_intr - Interrupt Handler
+ * @irq: interrupt number
+ * @data: pointer to a network interface device structure
+ **/
+static irqreturn_t e1000_intr(int irq, void *data)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl, icr = er32(ICR);
+
+ if (!icr || test_bit(__E1000_DOWN, &adapter->state))
+ return IRQ_NONE; /* Not our interrupt */
+
+ /*
+ * IMS will not auto-mask if INT_ASSERTED is not set, and if it is
+ * not set, then the adapter didn't send an interrupt
+ */
+ if (!adapter->ecdev && !(icr & E1000_ICR_INT_ASSERTED))
+ return IRQ_NONE;
+
+ /*
+ * Interrupt Auto-Mask...upon reading ICR,
+ * interrupts are masked. No need for the
+ * IMC write
+ */
+
+ if (!adapter->ecdev && (icr & E1000_ICR_LSC)) {
+ hw->mac.get_link_status = 1;
+ /*
+ * ICH8 workaround-- Call gig speed drop workaround on cable
+ * disconnect (LSC) before accessing any PHY registers
+ */
+ if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) &&
+ (!(er32(STATUS) & E1000_STATUS_LU)))
+ schedule_work(&adapter->downshift_task);
+
+ /*
+ * 80003ES2LAN workaround--
+ * For packet buffer work-around on link down event;
+ * disable receives here in the ISR and
+ * reset adapter in watchdog
+ */
+ if (netif_carrier_ok(netdev) &&
+ (adapter->flags & FLAG_RX_NEEDS_RESTART)) {
+ /* disable receives */
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ adapter->flags |= FLAG_RX_RESTART_NOW;
+ }
+ /* guard against interrupt when we're going down */
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->watchdog_timer, jiffies + 1);
+ }
+
+ if (adapter->ecdev) {
+ int ec_work_done = 0;
+ adapter->clean_rx(adapter, &ec_work_done, 100);
+ e1000_clean_tx_irq(adapter);
+ return IRQ_HANDLED;
+ }
+
+ if (napi_schedule_prep(&adapter->napi)) {
+ adapter->total_tx_bytes = 0;
+ adapter->total_tx_packets = 0;
+ adapter->total_rx_bytes = 0;
+ adapter->total_rx_packets = 0;
+ __napi_schedule(&adapter->napi);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t e1000_msix_other(int irq, void *data)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 icr = er32(ICR);
+
+ if (!(icr & E1000_ICR_INT_ASSERTED)) {
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ ew32(IMS, E1000_IMS_OTHER);
+ return IRQ_NONE;
+ }
+
+ if (icr & adapter->eiac_mask)
+ ew32(ICS, (icr & adapter->eiac_mask));
+
+ if (icr & E1000_ICR_OTHER) {
+ if (!(icr & E1000_ICR_LSC))
+ goto no_link_interrupt;
+ hw->mac.get_link_status = 1;
+ /* guard against interrupt when we're going down */
+ if (!adapter->ecdev && !test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->watchdog_timer, jiffies + 1);
+ }
+
+no_link_interrupt:
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ ew32(IMS, E1000_IMS_LSC | E1000_IMS_OTHER);
+
+ return IRQ_HANDLED;
+}
+
+
+static irqreturn_t e1000_intr_msix_tx(int irq, void *data)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+
+
+ adapter->total_tx_bytes = 0;
+ adapter->total_tx_packets = 0;
+
+ if (!e1000_clean_tx_irq(adapter))
+ /* Ring was not completely cleaned, so fire another interrupt */
+ ew32(ICS, tx_ring->ims_val);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t e1000_intr_msix_rx(int irq, void *data)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ /* Write the ITR value calculated at the end of the
+ * previous interrupt.
+ */
+ if (adapter->rx_ring->set_itr) {
+ writel(1000000000 / (adapter->rx_ring->itr_val * 256),
+ adapter->hw.hw_addr + adapter->rx_ring->itr_register);
+ adapter->rx_ring->set_itr = 0;
+ }
+
+ if (adapter->ecdev) {
+ int ec_work_done = 0;
+ adapter->clean_rx(adapter, &ec_work_done, 100);
+ } else {
+ if (napi_schedule_prep(&adapter->napi)) {
+ adapter->total_rx_bytes = 0;
+ adapter->total_rx_packets = 0;
+ __napi_schedule(&adapter->napi);
+ }
+ }
+ return IRQ_HANDLED;
+}
+
+/**
+ * e1000_configure_msix - Configure MSI-X hardware
+ *
+ * e1000_configure_msix sets up the hardware to properly
+ * generate MSI-X interrupts.
+ **/
+static void e1000_configure_msix(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ int vector = 0;
+ u32 ctrl_ext, ivar = 0;
+
+ adapter->eiac_mask = 0;
+
+ /* Workaround issue with spurious interrupts on 82574 in MSI-X mode */
+ if (hw->mac.type == e1000_82574) {
+ u32 rfctl = er32(RFCTL);
+ rfctl |= E1000_RFCTL_ACK_DIS;
+ ew32(RFCTL, rfctl);
+ }
+
+#define E1000_IVAR_INT_ALLOC_VALID 0x8
+ /* Configure Rx vector */
+ rx_ring->ims_val = E1000_IMS_RXQ0;
+ adapter->eiac_mask |= rx_ring->ims_val;
+ if (rx_ring->itr_val)
+ writel(1000000000 / (rx_ring->itr_val * 256),
+ hw->hw_addr + rx_ring->itr_register);
+ else
+ writel(1, hw->hw_addr + rx_ring->itr_register);
+ ivar = E1000_IVAR_INT_ALLOC_VALID | vector;
+
+ /* Configure Tx vector */
+ tx_ring->ims_val = E1000_IMS_TXQ0;
+ vector++;
+ if (tx_ring->itr_val)
+ writel(1000000000 / (tx_ring->itr_val * 256),
+ hw->hw_addr + tx_ring->itr_register);
+ else
+ writel(1, hw->hw_addr + tx_ring->itr_register);
+ adapter->eiac_mask |= tx_ring->ims_val;
+ ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 8);
+
+ /* set vector for Other Causes, e.g. link changes */
+ vector++;
+ ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 16);
+ if (rx_ring->itr_val)
+ writel(1000000000 / (rx_ring->itr_val * 256),
+ hw->hw_addr + E1000_EITR_82574(vector));
+ else
+ writel(1, hw->hw_addr + E1000_EITR_82574(vector));
+
+ /* Cause Tx interrupts on every write back */
+ ivar |= (1 << 31);
+
+ ew32(IVAR, ivar);
+
+ /* enable MSI-X PBA support */
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_PBA_CLR;
+
+ /* Auto-Mask Other interrupts upon ICR read */
+#define E1000_EIAC_MASK_82574 0x01F00000
+ ew32(IAM, ~E1000_EIAC_MASK_82574 | E1000_IMS_OTHER);
+ ctrl_ext |= E1000_CTRL_EXT_EIAME;
+ ew32(CTRL_EXT, ctrl_ext);
+ e1e_flush();
+}
+
+void e1000e_reset_interrupt_capability(struct e1000_adapter *adapter)
+{
+ if (adapter->msix_entries) {
+ pci_disable_msix(adapter->pdev);
+ kfree(adapter->msix_entries);
+ adapter->msix_entries = NULL;
+ } else if (adapter->flags & FLAG_MSI_ENABLED) {
+ pci_disable_msi(adapter->pdev);
+ adapter->flags &= ~FLAG_MSI_ENABLED;
+ }
+}
+
+/**
+ * e1000e_set_interrupt_capability - set MSI or MSI-X if supported
+ *
+ * Attempt to configure interrupts using the best available
+ * capabilities of the hardware and kernel.
+ **/
+void e1000e_set_interrupt_capability(struct e1000_adapter *adapter)
+{
+ int err;
+ int numvecs, i;
+
+
+ switch (adapter->int_mode) {
+ case E1000E_INT_MODE_MSIX:
+ if (adapter->flags & FLAG_HAS_MSIX) {
+ numvecs = 3; /* RxQ0, TxQ0 and other */
+ adapter->msix_entries = kcalloc(numvecs,
+ sizeof(struct msix_entry),
+ GFP_KERNEL);
+ if (adapter->msix_entries) {
+ for (i = 0; i < numvecs; i++)
+ adapter->msix_entries[i].entry = i;
+
+ err = pci_enable_msix(adapter->pdev,
+ adapter->msix_entries,
+ numvecs);
+ if (err == 0)
+ return;
+ }
+ /* MSI-X failed, so fall through and try MSI */
+ e_err("Failed to initialize MSI-X interrupts. "
+ "Falling back to MSI interrupts.\n");
+ e1000e_reset_interrupt_capability(adapter);
+ }
+ adapter->int_mode = E1000E_INT_MODE_MSI;
+ /* Fall through */
+ case E1000E_INT_MODE_MSI:
+ if (!pci_enable_msi(adapter->pdev)) {
+ adapter->flags |= FLAG_MSI_ENABLED;
+ } else {
+ adapter->int_mode = E1000E_INT_MODE_LEGACY;
+ e_err("Failed to initialize MSI interrupts. Falling "
+ "back to legacy interrupts.\n");
+ }
+ /* Fall through */
+ case E1000E_INT_MODE_LEGACY:
+ /* Don't do anything; this is the system default */
+ break;
+ }
+}
+
+/**
+ * e1000_request_msix - Initialize MSI-X interrupts
+ *
+ * e1000_request_msix allocates MSI-X vectors and requests interrupts from the
+ * kernel.
+ **/
+static int e1000_request_msix(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ int err = 0, vector = 0;
+
+ if (strlen(netdev->name) < (IFNAMSIZ - 5))
+ sprintf(adapter->rx_ring->name, "%s-rx-0", netdev->name);
+ else
+ memcpy(adapter->rx_ring->name, netdev->name, IFNAMSIZ);
+ err = request_irq(adapter->msix_entries[vector].vector,
+ e1000_intr_msix_rx, 0, adapter->rx_ring->name,
+ netdev);
+ if (err)
+ goto out;
+ adapter->rx_ring->itr_register = E1000_EITR_82574(vector);
+ adapter->rx_ring->itr_val = adapter->itr;
+ vector++;
+
+ if (strlen(netdev->name) < (IFNAMSIZ - 5))
+ sprintf(adapter->tx_ring->name, "%s-tx-0", netdev->name);
+ else
+ memcpy(adapter->tx_ring->name, netdev->name, IFNAMSIZ);
+ err = request_irq(adapter->msix_entries[vector].vector,
+ e1000_intr_msix_tx, 0, adapter->tx_ring->name,
+ netdev);
+ if (err)
+ goto out;
+ adapter->tx_ring->itr_register = E1000_EITR_82574(vector);
+ adapter->tx_ring->itr_val = adapter->itr;
+ vector++;
+
+ err = request_irq(adapter->msix_entries[vector].vector,
+ e1000_msix_other, 0, netdev->name, netdev);
+ if (err)
+ goto out;
+
+ e1000_configure_msix(adapter);
+ return 0;
+out:
+ return err;
+}
+
+/**
+ * e1000_request_irq - initialize interrupts
+ *
+ * Attempts to configure interrupts using the best available
+ * capabilities of the hardware and kernel.
+ **/
+static int e1000_request_irq(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ int err;
+
+ if (adapter->ecdev)
+ return 0;
+
+ if (adapter->msix_entries) {
+ err = e1000_request_msix(adapter);
+ if (!err)
+ return err;
+ /* fall back to MSI */
+ e1000e_reset_interrupt_capability(adapter);
+ adapter->int_mode = E1000E_INT_MODE_MSI;
+ e1000e_set_interrupt_capability(adapter);
+ }
+ if (adapter->flags & FLAG_MSI_ENABLED) {
+ err = request_irq(adapter->pdev->irq, e1000_intr_msi, 0,
+ netdev->name, netdev);
+ if (!err)
+ return err;
+
+ /* fall back to legacy interrupt */
+ e1000e_reset_interrupt_capability(adapter);
+ adapter->int_mode = E1000E_INT_MODE_LEGACY;
+ }
+
+ err = request_irq(adapter->pdev->irq, e1000_intr, IRQF_SHARED,
+ netdev->name, netdev);
+ if (err)
+ e_err("Unable to allocate interrupt, Error: %d\n", err);
+
+ return err;
+}
+
+static void e1000_free_irq(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+
+ if (adapter->ecdev)
+ return;
+
+ if (adapter->msix_entries) {
+ int vector = 0;
+
+ free_irq(adapter->msix_entries[vector].vector, netdev);
+ vector++;
+
+ free_irq(adapter->msix_entries[vector].vector, netdev);
+ vector++;
+
+ /* Other Causes interrupt vector */
+ free_irq(adapter->msix_entries[vector].vector, netdev);
+ return;
+ }
+
+ free_irq(adapter->pdev->irq, netdev);
+}
+
+/**
+ * e1000_irq_disable - Mask off interrupt generation on the NIC
+ **/
+static void e1000_irq_disable(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (adapter->ecdev)
+ return;
+
+ ew32(IMC, ~0);
+ if (adapter->msix_entries)
+ ew32(EIAC_82574, 0);
+ e1e_flush();
+ synchronize_irq(adapter->pdev->irq);
+}
+
+/**
+ * e1000_irq_enable - Enable default interrupt generation settings
+ **/
+static void e1000_irq_enable(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (adapter->ecdev)
+ return;
+
+ if (adapter->msix_entries) {
+ ew32(EIAC_82574, adapter->eiac_mask & E1000_EIAC_MASK_82574);
+ ew32(IMS, adapter->eiac_mask | E1000_IMS_OTHER | E1000_IMS_LSC);
+ } else {
+ ew32(IMS, IMS_ENABLE_MASK);
+ }
+ e1e_flush();
+}
+
+/**
+ * e1000_get_hw_control - get control of the h/w from f/w
+ * @adapter: address of board private structure
+ *
+ * e1000_get_hw_control sets {CTRL_EXT|SWSM}:DRV_LOAD bit.
+ * For ASF and Pass Through versions of f/w this means that
+ * the driver is loaded. For AMT version (only with 82573)
+ * of the f/w this means that the network i/f is open.
+ **/
+static void e1000_get_hw_control(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl_ext;
+ u32 swsm;
+
+ /* Let firmware know the driver has taken over */
+ if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) {
+ swsm = er32(SWSM);
+ ew32(SWSM, swsm | E1000_SWSM_DRV_LOAD);
+ } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) {
+ ctrl_ext = er32(CTRL_EXT);
+ ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_DRV_LOAD);
+ }
+}
+
+/**
+ * e1000_release_hw_control - release control of the h/w to f/w
+ * @adapter: address of board private structure
+ *
+ * e1000_release_hw_control resets {CTRL_EXT|SWSM}:DRV_LOAD bit.
+ * For ASF and Pass Through versions of f/w this means that the
+ * driver is no longer loaded. For AMT version (only with 82573) i
+ * of the f/w this means that the network i/f is closed.
+ *
+ **/
+static void e1000_release_hw_control(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl_ext;
+ u32 swsm;
+
+ /* Let firmware taken over control of h/w */
+ if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) {
+ swsm = er32(SWSM);
+ ew32(SWSM, swsm & ~E1000_SWSM_DRV_LOAD);
+ } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) {
+ ctrl_ext = er32(CTRL_EXT);
+ ew32(CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD);
+ }
+}
+
+/**
+ * @e1000_alloc_ring - allocate memory for a ring structure
+ **/
+static int e1000_alloc_ring_dma(struct e1000_adapter *adapter,
+ struct e1000_ring *ring)
+{
+ struct pci_dev *pdev = adapter->pdev;
+
+ ring->desc = dma_alloc_coherent(&pdev->dev, ring->size, &ring->dma,
+ GFP_KERNEL);
+ if (!ring->desc)
+ return -ENOMEM;
+
+ return 0;
+}
+
+/**
+ * e1000e_setup_tx_resources - allocate Tx resources (Descriptors)
+ * @adapter: board private structure
+ *
+ * Return 0 on success, negative on failure
+ **/
+int e1000e_setup_tx_resources(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ int err = -ENOMEM, size;
+
+ size = sizeof(struct e1000_buffer) * tx_ring->count;
+ tx_ring->buffer_info = vmalloc(size);
+ if (!tx_ring->buffer_info)
+ goto err;
+ memset(tx_ring->buffer_info, 0, size);
+
+ /* round up to nearest 4K */
+ tx_ring->size = tx_ring->count * sizeof(struct e1000_tx_desc);
+ tx_ring->size = ALIGN(tx_ring->size, 4096);
+
+ err = e1000_alloc_ring_dma(adapter, tx_ring);
+ if (err)
+ goto err;
+
+ tx_ring->next_to_use = 0;
+ tx_ring->next_to_clean = 0;
+
+ return 0;
+err:
+ vfree(tx_ring->buffer_info);
+ e_err("Unable to allocate memory for the transmit descriptor ring\n");
+ return err;
+}
+
+/**
+ * e1000e_setup_rx_resources - allocate Rx resources (Descriptors)
+ * @adapter: board private structure
+ *
+ * Returns 0 on success, negative on failure
+ **/
+int e1000e_setup_rx_resources(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_buffer *buffer_info;
+ int i, size, desc_len, err = -ENOMEM;
+
+ size = sizeof(struct e1000_buffer) * rx_ring->count;
+ rx_ring->buffer_info = vmalloc(size);
+ if (!rx_ring->buffer_info)
+ goto err;
+ memset(rx_ring->buffer_info, 0, size);
+
+ for (i = 0; i < rx_ring->count; i++) {
+ buffer_info = &rx_ring->buffer_info[i];
+ buffer_info->ps_pages = kcalloc(PS_PAGE_BUFFERS,
+ sizeof(struct e1000_ps_page),
+ GFP_KERNEL);
+ if (!buffer_info->ps_pages)
+ goto err_pages;
+ }
+
+ desc_len = sizeof(union e1000_rx_desc_packet_split);
+
+ /* Round up to nearest 4K */
+ rx_ring->size = rx_ring->count * desc_len;
+ rx_ring->size = ALIGN(rx_ring->size, 4096);
+
+ err = e1000_alloc_ring_dma(adapter, rx_ring);
+ if (err)
+ goto err_pages;
+
+ rx_ring->next_to_clean = 0;
+ rx_ring->next_to_use = 0;
+ rx_ring->rx_skb_top = NULL;
+
+ return 0;
+
+err_pages:
+ for (i = 0; i < rx_ring->count; i++) {
+ buffer_info = &rx_ring->buffer_info[i];
+ kfree(buffer_info->ps_pages);
+ }
+err:
+ vfree(rx_ring->buffer_info);
+ e_err("Unable to allocate memory for the transmit descriptor ring\n");
+ return err;
+}
+
+/**
+ * e1000_clean_tx_ring - Free Tx Buffers
+ * @adapter: board private structure
+ **/
+static void e1000_clean_tx_ring(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_buffer *buffer_info;
+ unsigned long size;
+ unsigned int i;
+
+ for (i = 0; i < tx_ring->count; i++) {
+ buffer_info = &tx_ring->buffer_info[i];
+ e1000_put_txbuf(adapter, buffer_info);
+ }
+
+ size = sizeof(struct e1000_buffer) * tx_ring->count;
+ memset(tx_ring->buffer_info, 0, size);
+
+ memset(tx_ring->desc, 0, tx_ring->size);
+
+ tx_ring->next_to_use = 0;
+ tx_ring->next_to_clean = 0;
+
+ writel(0, adapter->hw.hw_addr + tx_ring->head);
+ writel(0, adapter->hw.hw_addr + tx_ring->tail);
+}
+
+/**
+ * e1000e_free_tx_resources - Free Tx Resources per Queue
+ * @adapter: board private structure
+ *
+ * Free all transmit software resources
+ **/
+void e1000e_free_tx_resources(struct e1000_adapter *adapter)
+{
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+
+ e1000_clean_tx_ring(adapter);
+
+ vfree(tx_ring->buffer_info);
+ tx_ring->buffer_info = NULL;
+
+ dma_free_coherent(&pdev->dev, tx_ring->size, tx_ring->desc,
+ tx_ring->dma);
+ tx_ring->desc = NULL;
+}
+
+/**
+ * e1000e_free_rx_resources - Free Rx Resources
+ * @adapter: board private structure
+ *
+ * Free all receive software resources
+ **/
+
+void e1000e_free_rx_resources(struct e1000_adapter *adapter)
+{
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ int i;
+
+ e1000_clean_rx_ring(adapter);
+
+ for (i = 0; i < rx_ring->count; i++) {
+ kfree(rx_ring->buffer_info[i].ps_pages);
+ }
+
+ vfree(rx_ring->buffer_info);
+ rx_ring->buffer_info = NULL;
+
+ dma_free_coherent(&pdev->dev, rx_ring->size, rx_ring->desc,
+ rx_ring->dma);
+ rx_ring->desc = NULL;
+}
+
+/**
+ * e1000_update_itr - update the dynamic ITR value based on statistics
+ * @adapter: pointer to adapter
+ * @itr_setting: current adapter->itr
+ * @packets: the number of packets during this measurement interval
+ * @bytes: the number of bytes during this measurement interval
+ *
+ * Stores a new ITR value based on packets and byte
+ * counts during the last interrupt. The advantage of per interrupt
+ * computation is faster updates and more accurate ITR for the current
+ * traffic pattern. Constants in this function were computed
+ * based on theoretical maximum wire speed and thresholds were set based
+ * on testing data as well as attempting to minimize response time
+ * while increasing bulk throughput. This functionality is controlled
+ * by the InterruptThrottleRate module parameter.
+ **/
+static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
+ u16 itr_setting, int packets,
+ int bytes)
+{
+ unsigned int retval = itr_setting;
+
+ if (packets == 0)
+ goto update_itr_done;
+
+ switch (itr_setting) {
+ case lowest_latency:
+ /* handle TSO and jumbo frames */
+ if (bytes/packets > 8000)
+ retval = bulk_latency;
+ else if ((packets < 5) && (bytes > 512)) {
+ retval = low_latency;
+ }
+ break;
+ case low_latency: /* 50 usec aka 20000 ints/s */
+ if (bytes > 10000) {
+ /* this if handles the TSO accounting */
+ if (bytes/packets > 8000) {
+ retval = bulk_latency;
+ } else if ((packets < 10) || ((bytes/packets) > 1200)) {
+ retval = bulk_latency;
+ } else if ((packets > 35)) {
+ retval = lowest_latency;
+ }
+ } else if (bytes/packets > 2000) {
+ retval = bulk_latency;
+ } else if (packets <= 2 && bytes < 512) {
+ retval = lowest_latency;
+ }
+ break;
+ case bulk_latency: /* 250 usec aka 4000 ints/s */
+ if (bytes > 25000) {
+ if (packets > 35) {
+ retval = low_latency;
+ }
+ } else if (bytes < 6000) {
+ retval = low_latency;
+ }
+ break;
+ }
+
+update_itr_done:
+ return retval;
+}
+
+static void e1000_set_itr(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 current_itr;
+ u32 new_itr = adapter->itr;
+
+ /* for non-gigabit speeds, just fix the interrupt rate at 4000 */
+ if (adapter->link_speed != SPEED_1000) {
+ current_itr = 0;
+ new_itr = 4000;
+ goto set_itr_now;
+ }
+
+ adapter->tx_itr = e1000_update_itr(adapter,
+ adapter->tx_itr,
+ adapter->total_tx_packets,
+ adapter->total_tx_bytes);
+ /* conservative mode (itr 3) eliminates the lowest_latency setting */
+ if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency)
+ adapter->tx_itr = low_latency;
+
+ adapter->rx_itr = e1000_update_itr(adapter,
+ adapter->rx_itr,
+ adapter->total_rx_packets,
+ adapter->total_rx_bytes);
+ /* conservative mode (itr 3) eliminates the lowest_latency setting */
+ if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency)
+ adapter->rx_itr = low_latency;
+
+ current_itr = max(adapter->rx_itr, adapter->tx_itr);
+
+ switch (current_itr) {
+ /* counts and packets in update_itr are dependent on these numbers */
+ case lowest_latency:
+ new_itr = 70000;
+ break;
+ case low_latency:
+ new_itr = 20000; /* aka hwitr = ~200 */
+ break;
+ case bulk_latency:
+ new_itr = 4000;
+ break;
+ default:
+ break;
+ }
+
+set_itr_now:
+ if (new_itr != adapter->itr) {
+ /*
+ * this attempts to bias the interrupt rate towards Bulk
+ * by adding intermediate steps when interrupt rate is
+ * increasing
+ */
+ new_itr = new_itr > adapter->itr ?
+ min(adapter->itr + (new_itr >> 2), new_itr) :
+ new_itr;
+ adapter->itr = new_itr;
+ adapter->rx_ring->itr_val = new_itr;
+ if (adapter->msix_entries)
+ adapter->rx_ring->set_itr = 1;
+ else
+ ew32(ITR, 1000000000 / (new_itr * 256));
+ }
+}
+
+/**
+ * e1000_alloc_queues - Allocate memory for all rings
+ * @adapter: board private structure to initialize
+ **/
+static int __devinit e1000_alloc_queues(struct e1000_adapter *adapter)
+{
+ adapter->tx_ring = kzalloc(sizeof(struct e1000_ring), GFP_KERNEL);
+ if (!adapter->tx_ring)
+ goto err;
+
+ adapter->rx_ring = kzalloc(sizeof(struct e1000_ring), GFP_KERNEL);
+ if (!adapter->rx_ring)
+ goto err;
+
+ return 0;
+err:
+ e_err("Unable to allocate memory for queues\n");
+ kfree(adapter->rx_ring);
+ kfree(adapter->tx_ring);
+ return -ENOMEM;
+}
+
+/**
+ * e1000_clean - NAPI Rx polling callback
+ * @napi: struct associated with this polling callback
+ * @budget: amount of packets driver is allowed to process this poll
+ **/
+static int e1000_clean(struct napi_struct *napi, int budget)
+{
+ struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, napi);
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *poll_dev = adapter->netdev;
+ int tx_cleaned = 1, work_done = 0;
+
+ adapter = netdev_priv(poll_dev);
+
+ if (adapter->msix_entries &&
+ !(adapter->rx_ring->ims_val & adapter->tx_ring->ims_val))
+ goto clean_rx;
+
+ tx_cleaned = e1000_clean_tx_irq(adapter);
+
+clean_rx:
+ adapter->clean_rx(adapter, &work_done, budget);
+
+ if (!tx_cleaned)
+ work_done = budget;
+
+ /* If budget not fully consumed, exit the polling mode */
+ if (work_done < budget) {
+ if (adapter->itr_setting & 3)
+ e1000_set_itr(adapter);
+ napi_complete(napi);
+ if (!test_bit(__E1000_DOWN, &adapter->state)) {
+ if (adapter->msix_entries)
+ ew32(IMS, adapter->rx_ring->ims_val);
+ else
+ e1000_irq_enable(adapter);
+ }
+ }
+
+ return work_done;
+}
+
+static void e1000_vlan_rx_add_vid(struct net_device *netdev, u16 vid)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 vfta, index;
+
+ /* don't update vlan cookie if already programmed */
+ if ((adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
+ (vid == adapter->mng_vlan_id))
+ return;
+
+ /* add VID to filter table */
+ if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
+ index = (vid >> 5) & 0x7F;
+ vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index);
+ vfta |= (1 << (vid & 0x1F));
+ hw->mac.ops.write_vfta(hw, index, vfta);
+ }
+}
+
+static void e1000_vlan_rx_kill_vid(struct net_device *netdev, u16 vid)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 vfta, index;
+
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ e1000_irq_disable(adapter);
+ vlan_group_set_device(adapter->vlgrp, vid, NULL);
+
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ e1000_irq_enable(adapter);
+
+ if ((adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
+ (vid == adapter->mng_vlan_id)) {
+ /* release control to f/w */
+ e1000_release_hw_control(adapter);
+ return;
+ }
+
+ /* remove VID from filter table */
+ if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
+ index = (vid >> 5) & 0x7F;
+ vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index);
+ vfta &= ~(1 << (vid & 0x1F));
+ hw->mac.ops.write_vfta(hw, index, vfta);
+ }
+}
+
+static void e1000_update_mng_vlan(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ u16 vid = adapter->hw.mng_cookie.vlan_id;
+ u16 old_vid = adapter->mng_vlan_id;
+
+ if (!adapter->vlgrp)
+ return;
+
+ if (!vlan_group_get_device(adapter->vlgrp, vid)) {
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+ if (adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN) {
+ e1000_vlan_rx_add_vid(netdev, vid);
+ adapter->mng_vlan_id = vid;
+ }
+
+ if ((old_vid != (u16)E1000_MNG_VLAN_NONE) &&
+ (vid != old_vid) &&
+ !vlan_group_get_device(adapter->vlgrp, old_vid))
+ e1000_vlan_rx_kill_vid(netdev, old_vid);
+ } else {
+ adapter->mng_vlan_id = vid;
+ }
+}
+
+
+static void e1000_vlan_rx_register(struct net_device *netdev,
+ struct vlan_group *grp)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl, rctl;
+
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ e1000_irq_disable(adapter);
+ adapter->vlgrp = grp;
+
+ if (grp) {
+ /* enable VLAN tag insert/strip */
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_VME;
+ ew32(CTRL, ctrl);
+
+ if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
+ /* enable VLAN receive filtering */
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_CFIEN;
+ ew32(RCTL, rctl);
+ e1000_update_mng_vlan(adapter);
+ }
+ } else {
+ /* disable VLAN tag insert/strip */
+ ctrl = er32(CTRL);
+ ctrl &= ~E1000_CTRL_VME;
+ ew32(CTRL, ctrl);
+
+ if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
+ if (adapter->mng_vlan_id !=
+ (u16)E1000_MNG_VLAN_NONE) {
+ e1000_vlan_rx_kill_vid(netdev,
+ adapter->mng_vlan_id);
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+ }
+ }
+ }
+
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ e1000_irq_enable(adapter);
+}
+
+static void e1000_restore_vlan(struct e1000_adapter *adapter)
+{
+ u16 vid;
+
+ e1000_vlan_rx_register(adapter->netdev, adapter->vlgrp);
+
+ if (!adapter->vlgrp)
+ return;
+
+ for (vid = 0; vid < VLAN_GROUP_ARRAY_LEN; vid++) {
+ if (!vlan_group_get_device(adapter->vlgrp, vid))
+ continue;
+ e1000_vlan_rx_add_vid(adapter->netdev, vid);
+ }
+}
+
+static void e1000_init_manageability_pt(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 manc, manc2h, mdef, i, j;
+
+ if (!(adapter->flags & FLAG_MNG_PT_ENABLED))
+ return;
+
+ manc = er32(MANC);
+
+ /*
+ * enable receiving management packets to the host. this will probably
+ * generate destination unreachable messages from the host OS, but
+ * the packets will be handled on SMBUS
+ */
+ manc |= E1000_MANC_EN_MNG2HOST;
+ manc2h = er32(MANC2H);
+
+ switch (hw->mac.type) {
+ default:
+ manc2h |= (E1000_MANC2H_PORT_623 | E1000_MANC2H_PORT_664);
+ break;
+ case e1000_82574:
+ case e1000_82583:
+ /*
+ * Check if IPMI pass-through decision filter already exists;
+ * if so, enable it.
+ */
+ for (i = 0, j = 0; i < 8; i++) {
+ mdef = er32(MDEF(i));
+
+ /* Ignore filters with anything other than IPMI ports */
+ if (mdef & ~(E1000_MDEF_PORT_623 | E1000_MDEF_PORT_664))
+ continue;
+
+ /* Enable this decision filter in MANC2H */
+ if (mdef)
+ manc2h |= (1 << i);
+
+ j |= mdef;
+ }
+
+ if (j == (E1000_MDEF_PORT_623 | E1000_MDEF_PORT_664))
+ break;
+
+ /* Create new decision filter in an empty filter */
+ for (i = 0, j = 0; i < 8; i++)
+ if (er32(MDEF(i)) == 0) {
+ ew32(MDEF(i), (E1000_MDEF_PORT_623 |
+ E1000_MDEF_PORT_664));
+ manc2h |= (1 << 1);
+ j++;
+ break;
+ }
+
+ if (!j)
+ e_warn("Unable to create IPMI pass-through filter\n");
+ break;
+ }
+
+ ew32(MANC2H, manc2h);
+ ew32(MANC, manc);
+}
+
+/**
+ * e1000_configure_tx - Configure 8254x Transmit Unit after Reset
+ * @adapter: board private structure
+ *
+ * Configure the Tx unit of the MAC after a reset.
+ **/
+static void e1000_configure_tx(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ u64 tdba;
+ u32 tdlen, tctl, tipg, tarc;
+ u32 ipgr1, ipgr2;
+
+ /* Setup the HW Tx Head and Tail descriptor pointers */
+ tdba = tx_ring->dma;
+ tdlen = tx_ring->count * sizeof(struct e1000_tx_desc);
+ ew32(TDBAL, (tdba & DMA_BIT_MASK(32)));
+ ew32(TDBAH, (tdba >> 32));
+ ew32(TDLEN, tdlen);
+ ew32(TDH, 0);
+ ew32(TDT, 0);
+ tx_ring->head = E1000_TDH;
+ tx_ring->tail = E1000_TDT;
+
+ /* Set the default values for the Tx Inter Packet Gap timer */
+ tipg = DEFAULT_82543_TIPG_IPGT_COPPER; /* 8 */
+ ipgr1 = DEFAULT_82543_TIPG_IPGR1; /* 8 */
+ ipgr2 = DEFAULT_82543_TIPG_IPGR2; /* 6 */
+
+ if (adapter->flags & FLAG_TIPG_MEDIUM_FOR_80003ESLAN)
+ ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2; /* 7 */
+
+ tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT;
+ tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT;
+ ew32(TIPG, tipg);
+
+ /* Set the Tx Interrupt Delay register */
+ ew32(TIDV, adapter->tx_int_delay);
+ /* Tx irq moderation */
+ ew32(TADV, adapter->tx_abs_int_delay);
+
+ /* Program the Transmit Control Register */
+ tctl = er32(TCTL);
+ tctl &= ~E1000_TCTL_CT;
+ tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC |
+ (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
+
+ if (adapter->flags & FLAG_TARC_SPEED_MODE_BIT) {
+ tarc = er32(TARC(0));
+ /*
+ * set the speed mode bit, we'll clear it if we're not at
+ * gigabit link later
+ */
+#define SPEED_MODE_BIT (1 << 21)
+ tarc |= SPEED_MODE_BIT;
+ ew32(TARC(0), tarc);
+ }
+
+ /* errata: program both queues to unweighted RR */
+ if (adapter->flags & FLAG_TARC_SET_BIT_ZERO) {
+ tarc = er32(TARC(0));
+ tarc |= 1;
+ ew32(TARC(0), tarc);
+ tarc = er32(TARC(1));
+ tarc |= 1;
+ ew32(TARC(1), tarc);
+ }
+
+ /* Setup Transmit Descriptor Settings for eop descriptor */
+ adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
+
+ /* only set IDE if we are delaying interrupts using the timers */
+ if (adapter->tx_int_delay)
+ adapter->txd_cmd |= E1000_TXD_CMD_IDE;
+
+ /* enable Report Status bit */
+ adapter->txd_cmd |= E1000_TXD_CMD_RS;
+
+ ew32(TCTL, tctl);
+
+ e1000e_config_collision_dist(hw);
+}
+
+/**
+ * e1000_setup_rctl - configure the receive control registers
+ * @adapter: Board private structure
+ **/
+#define PAGE_USE_COUNT(S) (((S) >> PAGE_SHIFT) + \
+ (((S) & (PAGE_SIZE - 1)) ? 1 : 0))
+static void e1000_setup_rctl(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl, rfctl;
+ u32 psrctl = 0;
+ u32 pages = 0;
+
+ /* Program MC offset vector base */
+ rctl = er32(RCTL);
+ rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
+ rctl |= E1000_RCTL_EN | E1000_RCTL_BAM |
+ E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
+ (adapter->hw.mac.mc_filter_type << E1000_RCTL_MO_SHIFT);
+
+ /* Do not Store bad packets */
+ rctl &= ~E1000_RCTL_SBP;
+
+ /* Enable Long Packet receive */
+ if (adapter->netdev->mtu <= ETH_DATA_LEN)
+ rctl &= ~E1000_RCTL_LPE;
+ else
+ rctl |= E1000_RCTL_LPE;
+
+ /* Some systems expect that the CRC is included in SMBUS traffic. The
+ * hardware strips the CRC before sending to both SMBUS (BMC) and to
+ * host memory when this is enabled
+ */
+ if (adapter->flags2 & FLAG2_CRC_STRIPPING)
+ rctl |= E1000_RCTL_SECRC;
+
+ /* Workaround Si errata on 82577 PHY - configure IPG for jumbos */
+ if ((hw->phy.type == e1000_phy_82577) && (rctl & E1000_RCTL_LPE)) {
+ u16 phy_data;
+
+ e1e_rphy(hw, PHY_REG(770, 26), &phy_data);
+ phy_data &= 0xfff8;
+ phy_data |= (1 << 2);
+ e1e_wphy(hw, PHY_REG(770, 26), phy_data);
+
+ e1e_rphy(hw, 22, &phy_data);
+ phy_data &= 0x0fff;
+ phy_data |= (1 << 14);
+ e1e_wphy(hw, 0x10, 0x2823);
+ e1e_wphy(hw, 0x11, 0x0003);
+ e1e_wphy(hw, 22, phy_data);
+ }
+
+ /* Setup buffer sizes */
+ rctl &= ~E1000_RCTL_SZ_4096;
+ rctl |= E1000_RCTL_BSEX;
+ switch (adapter->rx_buffer_len) {
+ case 2048:
+ default:
+ rctl |= E1000_RCTL_SZ_2048;
+ rctl &= ~E1000_RCTL_BSEX;
+ break;
+ case 4096:
+ rctl |= E1000_RCTL_SZ_4096;
+ break;
+ case 8192:
+ rctl |= E1000_RCTL_SZ_8192;
+ break;
+ case 16384:
+ rctl |= E1000_RCTL_SZ_16384;
+ break;
+ }
+
+ /*
+ * 82571 and greater support packet-split where the protocol
+ * header is placed in skb->data and the packet data is
+ * placed in pages hanging off of skb_shinfo(skb)->nr_frags.
+ * In the case of a non-split, skb->data is linearly filled,
+ * followed by the page buffers. Therefore, skb->data is
+ * sized to hold the largest protocol header.
+ *
+ * allocations using alloc_page take too long for regular MTU
+ * so only enable packet split for jumbo frames
+ *
+ * Using pages when the page size is greater than 16k wastes
+ * a lot of memory, since we allocate 3 pages at all times
+ * per packet.
+ */
+ pages = PAGE_USE_COUNT(adapter->netdev->mtu);
+ if (!(adapter->flags & FLAG_IS_ICH) && (pages <= 3) &&
+ (PAGE_SIZE <= 16384) && (rctl & E1000_RCTL_LPE))
+ adapter->rx_ps_pages = pages;
+ else
+ adapter->rx_ps_pages = 0;
+
+ if (adapter->rx_ps_pages) {
+ /* Configure extra packet-split registers */
+ rfctl = er32(RFCTL);
+ rfctl |= E1000_RFCTL_EXTEN;
+ /*
+ * disable packet split support for IPv6 extension headers,
+ * because some malformed IPv6 headers can hang the Rx
+ */
+ rfctl |= (E1000_RFCTL_IPV6_EX_DIS |
+ E1000_RFCTL_NEW_IPV6_EXT_DIS);
+
+ ew32(RFCTL, rfctl);
+
+ /* Enable Packet split descriptors */
+ rctl |= E1000_RCTL_DTYP_PS;
+
+ psrctl |= adapter->rx_ps_bsize0 >>
+ E1000_PSRCTL_BSIZE0_SHIFT;
+
+ switch (adapter->rx_ps_pages) {
+ case 3:
+ psrctl |= PAGE_SIZE <<
+ E1000_PSRCTL_BSIZE3_SHIFT;
+ case 2:
+ psrctl |= PAGE_SIZE <<
+ E1000_PSRCTL_BSIZE2_SHIFT;
+ case 1:
+ psrctl |= PAGE_SIZE >>
+ E1000_PSRCTL_BSIZE1_SHIFT;
+ break;
+ }
+
+ ew32(PSRCTL, psrctl);
+ }
+
+ ew32(RCTL, rctl);
+ /* just started the receive unit, no need to restart */
+ adapter->flags &= ~FLAG_RX_RESTART_NOW;
+}
+
+/**
+ * e1000_configure_rx - Configure Receive Unit after Reset
+ * @adapter: board private structure
+ *
+ * Configure the Rx unit of the MAC after a reset.
+ **/
+static void e1000_configure_rx(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ u64 rdba;
+ u32 rdlen, rctl, rxcsum, ctrl_ext;
+
+ if (adapter->rx_ps_pages) {
+ /* this is a 32 byte descriptor */
+ rdlen = rx_ring->count *
+ sizeof(union e1000_rx_desc_packet_split);
+ adapter->clean_rx = e1000_clean_rx_irq_ps;
+ adapter->alloc_rx_buf = e1000_alloc_rx_buffers_ps;
+ } else if (adapter->netdev->mtu > ETH_FRAME_LEN + ETH_FCS_LEN) {
+ rdlen = rx_ring->count * sizeof(struct e1000_rx_desc);
+ adapter->clean_rx = e1000_clean_jumbo_rx_irq;
+ adapter->alloc_rx_buf = e1000_alloc_jumbo_rx_buffers;
+ } else {
+ rdlen = rx_ring->count * sizeof(struct e1000_rx_desc);
+ adapter->clean_rx = e1000_clean_rx_irq;
+ adapter->alloc_rx_buf = e1000_alloc_rx_buffers;
+ }
+
+ /* disable receives while setting up the descriptors */
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ e1e_flush();
+ msleep(10);
+
+ /* set the Receive Delay Timer Register */
+ ew32(RDTR, adapter->rx_int_delay);
+
+ /* irq moderation */
+ ew32(RADV, adapter->rx_abs_int_delay);
+ if (adapter->itr_setting != 0)
+ ew32(ITR, 1000000000 / (adapter->itr * 256));
+
+ ctrl_ext = er32(CTRL_EXT);
+ /* Auto-Mask interrupts upon ICR access */
+ ctrl_ext |= E1000_CTRL_EXT_IAME;
+ ew32(IAM, 0xffffffff);
+ ew32(CTRL_EXT, ctrl_ext);
+ e1e_flush();
+
+ /*
+ * Setup the HW Rx Head and Tail Descriptor Pointers and
+ * the Base and Length of the Rx Descriptor Ring
+ */
+ rdba = rx_ring->dma;
+ ew32(RDBAL, (rdba & DMA_BIT_MASK(32)));
+ ew32(RDBAH, (rdba >> 32));
+ ew32(RDLEN, rdlen);
+ ew32(RDH, 0);
+ ew32(RDT, 0);
+ rx_ring->head = E1000_RDH;
+ rx_ring->tail = E1000_RDT;
+
+ /* Enable Receive Checksum Offload for TCP and UDP */
+ rxcsum = er32(RXCSUM);
+ if (adapter->flags & FLAG_RX_CSUM_ENABLED) {
+ rxcsum |= E1000_RXCSUM_TUOFL;
+
+ /*
+ * IPv4 payload checksum for UDP fragments must be
+ * used in conjunction with packet-split.
+ */
+ if (adapter->rx_ps_pages)
+ rxcsum |= E1000_RXCSUM_IPPCSE;
+ } else {
+ rxcsum &= ~E1000_RXCSUM_TUOFL;
+ /* no need to clear IPPCSE as it defaults to 0 */
+ }
+ ew32(RXCSUM, rxcsum);
+
+ /*
+ * Enable early receives on supported devices, only takes effect when
+ * packet size is equal or larger than the specified value (in 8 byte
+ * units), e.g. using jumbo frames when setting to E1000_ERT_2048
+ */
+ if (adapter->flags & FLAG_HAS_ERT) {
+ if (adapter->netdev->mtu > ETH_DATA_LEN) {
+ u32 rxdctl = er32(RXDCTL(0));
+ ew32(RXDCTL(0), rxdctl | 0x3);
+ ew32(ERT, E1000_ERT_2048 | (1 << 13));
+ /*
+ * With jumbo frames and early-receive enabled,
+ * excessive C-state transition latencies result in
+ * dropped transactions.
+ */
+ pm_qos_update_request(
+ adapter->netdev->pm_qos_req, 55);
+ } else {
+ pm_qos_update_request(
+ adapter->netdev->pm_qos_req,
+ PM_QOS_DEFAULT_VALUE);
+ }
+ }
+
+ /* Enable Receives */
+ ew32(RCTL, rctl);
+}
+
+/**
+ * e1000_update_mc_addr_list - Update Multicast addresses
+ * @hw: pointer to the HW structure
+ * @mc_addr_list: array of multicast addresses to program
+ * @mc_addr_count: number of multicast addresses to program
+ *
+ * Updates the Multicast Table Array.
+ * The caller must have a packed mc_addr_list of multicast addresses.
+ **/
+static void e1000_update_mc_addr_list(struct e1000_hw *hw, u8 *mc_addr_list,
+ u32 mc_addr_count)
+{
+ hw->mac.ops.update_mc_addr_list(hw, mc_addr_list, mc_addr_count);
+}
+
+/**
+ * e1000_set_multi - Multicast and Promiscuous mode set
+ * @netdev: network interface device structure
+ *
+ * The set_multi entry point is called whenever the multicast address
+ * list or the network interface flags are updated. This routine is
+ * responsible for configuring the hardware for proper multicast,
+ * promiscuous mode, and all-multi behavior.
+ **/
+static void e1000_set_multi(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct netdev_hw_addr *ha;
+ u8 *mta_list;
+ u32 rctl;
+ int i;
+
+ /* Check for Promiscuous and All Multicast modes */
+
+ rctl = er32(RCTL);
+
+ if (netdev->flags & IFF_PROMISC) {
+ rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE);
+ rctl &= ~E1000_RCTL_VFE;
+ } else {
+ if (netdev->flags & IFF_ALLMULTI) {
+ rctl |= E1000_RCTL_MPE;
+ rctl &= ~E1000_RCTL_UPE;
+ } else {
+ rctl &= ~(E1000_RCTL_UPE | E1000_RCTL_MPE);
+ }
+ if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER)
+ rctl |= E1000_RCTL_VFE;
+ }
+
+ ew32(RCTL, rctl);
+
+ if (!netdev_mc_empty(netdev)) {
+ mta_list = kmalloc(netdev_mc_count(netdev) * 6, GFP_ATOMIC);
+ if (!mta_list)
+ return;
+
+ /* prepare a packed array of only addresses. */
+ i = 0;
+ netdev_for_each_mc_addr(ha, netdev)
+ memcpy(mta_list + (i++ * ETH_ALEN), ha->addr, ETH_ALEN);
+
+ e1000_update_mc_addr_list(hw, mta_list, i);
+ kfree(mta_list);
+ } else {
+ /*
+ * if we're called from probe, we might not have
+ * anything to do here, so clear out the list
+ */
+ e1000_update_mc_addr_list(hw, NULL, 0);
+ }
+}
+
+/**
+ * e1000_configure - configure the hardware for Rx and Tx
+ * @adapter: private board structure
+ **/
+static void e1000_configure(struct e1000_adapter *adapter)
+{
+ e1000_set_multi(adapter->netdev);
+
+ e1000_restore_vlan(adapter);
+ e1000_init_manageability_pt(adapter);
+
+ e1000_configure_tx(adapter);
+ e1000_setup_rctl(adapter);
+ e1000_configure_rx(adapter);
+
+ if (adapter->ecdev) {
+ adapter->alloc_rx_buf(adapter, adapter->rx_ring->count);
+ } else {
+ adapter->alloc_rx_buf(adapter, e1000_desc_unused(adapter->rx_ring));
+ }
+}
+
+/**
+ * e1000e_power_up_phy - restore link in case the phy was powered down
+ * @adapter: address of board private structure
+ *
+ * The phy may be powered down to save power and turn off link when the
+ * driver is unloaded and wake on lan is not enabled (among others)
+ * *** this routine MUST be followed by a call to e1000e_reset ***
+ **/
+void e1000e_power_up_phy(struct e1000_adapter *adapter)
+{
+ if (adapter->hw.phy.ops.power_up)
+ adapter->hw.phy.ops.power_up(&adapter->hw);
+
+ adapter->hw.mac.ops.setup_link(&adapter->hw);
+}
+
+/**
+ * e1000_power_down_phy - Power down the PHY
+ *
+ * Power down the PHY so no link is implied when interface is down.
+ * The PHY cannot be powered down if management or WoL is active.
+ */
+static void e1000_power_down_phy(struct e1000_adapter *adapter)
+{
+ /* WoL is enabled */
+ if (adapter->wol)
+ return;
+
+ if (adapter->hw.phy.ops.power_down)
+ adapter->hw.phy.ops.power_down(&adapter->hw);
+}
+
+/**
+ * e1000e_reset - bring the hardware into a known good state
+ *
+ * This function boots the hardware and enables some settings that
+ * require a configuration cycle of the hardware - those cannot be
+ * set/changed during runtime. After reset the device needs to be
+ * properly configured for Rx, Tx etc.
+ */
+void e1000e_reset(struct e1000_adapter *adapter)
+{
+ struct e1000_mac_info *mac = &adapter->hw.mac;
+ struct e1000_fc_info *fc = &adapter->hw.fc;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 tx_space, min_tx_space, min_rx_space;
+ u32 pba = adapter->pba;
+ u16 hwm;
+
+ /* reset Packet Buffer Allocation to default */
+ ew32(PBA, pba);
+
+ if (adapter->max_frame_size > ETH_FRAME_LEN + ETH_FCS_LEN) {
+ /*
+ * To maintain wire speed transmits, the Tx FIFO should be
+ * large enough to accommodate two full transmit packets,
+ * rounded up to the next 1KB and expressed in KB. Likewise,
+ * the Rx FIFO should be large enough to accommodate at least
+ * one full receive packet and is similarly rounded up and
+ * expressed in KB.
+ */
+ pba = er32(PBA);
+ /* upper 16 bits has Tx packet buffer allocation size in KB */
+ tx_space = pba >> 16;
+ /* lower 16 bits has Rx packet buffer allocation size in KB */
+ pba &= 0xffff;
+ /*
+ * the Tx fifo also stores 16 bytes of information about the tx
+ * but don't include ethernet FCS because hardware appends it
+ */
+ min_tx_space = (adapter->max_frame_size +
+ sizeof(struct e1000_tx_desc) -
+ ETH_FCS_LEN) * 2;
+ min_tx_space = ALIGN(min_tx_space, 1024);
+ min_tx_space >>= 10;
+ /* software strips receive CRC, so leave room for it */
+ min_rx_space = adapter->max_frame_size;
+ min_rx_space = ALIGN(min_rx_space, 1024);
+ min_rx_space >>= 10;
+
+ /*
+ * If current Tx allocation is less than the min Tx FIFO size,
+ * and the min Tx FIFO size is less than the current Rx FIFO
+ * allocation, take space away from current Rx allocation
+ */
+ if ((tx_space < min_tx_space) &&
+ ((min_tx_space - tx_space) < pba)) {
+ pba -= min_tx_space - tx_space;
+
+ /*
+ * if short on Rx space, Rx wins and must trump tx
+ * adjustment or use Early Receive if available
+ */
+ if ((pba < min_rx_space) &&
+ (!(adapter->flags & FLAG_HAS_ERT)))
+ /* ERT enabled in e1000_configure_rx */
+ pba = min_rx_space;
+ }
+
+ ew32(PBA, pba);
+ }
+
+
+ /*
+ * flow control settings
+ *
+ * The high water mark must be low enough to fit one full frame
+ * (or the size used for early receive) above it in the Rx FIFO.
+ * Set it to the lower of:
+ * - 90% of the Rx FIFO size, and
+ * - the full Rx FIFO size minus the early receive size (for parts
+ * with ERT support assuming ERT set to E1000_ERT_2048), or
+ * - the full Rx FIFO size minus one full frame
+ */
+ if (hw->mac.type == e1000_pchlan) {
+ /*
+ * Workaround PCH LOM adapter hangs with certain network
+ * loads. If hangs persist, try disabling Tx flow control.
+ */
+ if (adapter->netdev->mtu > ETH_DATA_LEN) {
+ fc->high_water = 0x3500;
+ fc->low_water = 0x1500;
+ } else {
+ fc->high_water = 0x5000;
+ fc->low_water = 0x3000;
+ }
+ fc->refresh_time = 0x1000;
+ } else {
+ if ((adapter->flags & FLAG_HAS_ERT) &&
+ (adapter->netdev->mtu > ETH_DATA_LEN))
+ hwm = min(((pba << 10) * 9 / 10),
+ ((pba << 10) - (E1000_ERT_2048 << 3)));
+ else
+ hwm = min(((pba << 10) * 9 / 10),
+ ((pba << 10) - adapter->max_frame_size));
+
+ fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
+ fc->low_water = fc->high_water - 8;
+ }
+
+ if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME)
+ fc->pause_time = 0xFFFF;
+ else
+ fc->pause_time = E1000_FC_PAUSE_TIME;
+ fc->send_xon = 1;
+ fc->current_mode = fc->requested_mode;
+
+ /* Allow time for pending master requests to run */
+ mac->ops.reset_hw(hw);
+
+ /*
+ * For parts with AMT enabled, let the firmware know
+ * that the network interface is in control
+ */
+ if (adapter->flags & FLAG_HAS_AMT)
+ e1000_get_hw_control(adapter);
+
+ ew32(WUC, 0);
+ if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP)
+ e1e_wphy(&adapter->hw, BM_WUC, 0);
+
+ if (mac->ops.init_hw(hw))
+ e_err("Hardware Error\n");
+
+ e1000_update_mng_vlan(adapter);
+
+ /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
+ ew32(VET, ETH_P_8021Q);
+
+ e1000e_reset_adaptive(hw);
+ e1000_get_phy_info(hw);
+
+ if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN) &&
+ !(adapter->flags & FLAG_SMART_POWER_DOWN)) {
+ u16 phy_data = 0;
+ /*
+ * speed up time to link by disabling smart power down, ignore
+ * the return value of this function because there is nothing
+ * different we would do if it failed
+ */
+ e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
+ phy_data &= ~IGP02E1000_PM_SPD;
+ e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
+ }
+}
+
+int e1000e_up(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ /* DMA latency requirement to workaround early-receive/jumbo issue */
+ if (adapter->flags & FLAG_HAS_ERT)
+ adapter->netdev->pm_qos_req =
+ pm_qos_add_request(PM_QOS_CPU_DMA_LATENCY,
+ PM_QOS_DEFAULT_VALUE);
+
+ /* hardware has been reset, we need to reload some things */
+ e1000_configure(adapter);
+
+ clear_bit(__E1000_DOWN, &adapter->state);
+
+ if (!adapter->ecdev) {
+ napi_enable(&adapter->napi);
+ }
+
+ if (adapter->msix_entries)
+ e1000_configure_msix(adapter);
+ if (!adapter->ecdev) {
+ e1000_irq_enable(adapter);
+
+ netif_wake_queue(adapter->netdev);
+
+ /* fire a link change interrupt to start the watchdog */
+ if (adapter->msix_entries)
+ ew32(ICS, E1000_ICS_LSC | E1000_ICR_OTHER);
+ else
+ ew32(ICS, E1000_ICS_LSC);
+ }
+
+ return 0;
+}
+
+void e1000e_down(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 tctl, rctl;
+
+ /*
+ * signal that we're down so the interrupt handler does not
+ * reschedule our watchdog timer
+ */
+ set_bit(__E1000_DOWN, &adapter->state);
+
+ /* disable receives in the hardware */
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ /* flush and sleep below */
+
+ if (!adapter->ecdev)
+ netif_stop_queue(netdev);
+
+ /* disable transmits in the hardware */
+ tctl = er32(TCTL);
+ tctl &= ~E1000_TCTL_EN;
+ ew32(TCTL, tctl);
+ /* flush both disables and wait for them to finish */
+ e1e_flush();
+ msleep(10);
+
+ if (!adapter->ecdev) {
+ napi_disable(&adapter->napi);
+ e1000_irq_disable(adapter);
+ del_timer_sync(&adapter->watchdog_timer);
+ del_timer_sync(&adapter->phy_info_timer);
+ }
+
+ if (adapter->ecdev) {
+ ecdev_set_link(adapter->ecdev, 0);
+ } else {
+ netif_carrier_off(netdev);
+ }
+ adapter->link_speed = 0;
+ adapter->link_duplex = 0;
+
+ if (!pci_channel_offline(adapter->pdev))
+ e1000e_reset(adapter);
+ e1000_clean_tx_ring(adapter);
+ e1000_clean_rx_ring(adapter);
+
+ if (adapter->flags & FLAG_HAS_ERT) {
+ pm_qos_remove_request(
+ adapter->netdev->pm_qos_req);
+ adapter->netdev->pm_qos_req = NULL;
+ }
+
+ /*
+ * TODO: for power management, we could drop the link and
+ * pci_disable_device here.
+ */
+}
+
+void e1000e_reinit_locked(struct e1000_adapter *adapter)
+{
+ might_sleep();
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
+ msleep(1);
+ e1000e_down(adapter);
+ e1000e_up(adapter);
+ clear_bit(__E1000_RESETTING, &adapter->state);
+}
+
+/**
+ * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
+ * @adapter: board private structure to initialize
+ *
+ * e1000_sw_init initializes the Adapter private data structure.
+ * Fields are initialized based on PCI device information and
+ * OS network device settings (MTU size).
+ **/
+static int __devinit e1000_sw_init(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+
+ adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN;
+ adapter->rx_ps_bsize0 = 128;
+ adapter->max_frame_size = netdev->mtu + ETH_HLEN + ETH_FCS_LEN;
+ adapter->min_frame_size = ETH_ZLEN + ETH_FCS_LEN;
+
+ e1000e_set_interrupt_capability(adapter);
+
+ if (e1000_alloc_queues(adapter))
+ return -ENOMEM;
+
+ /* Explicitly disable IRQ since the NIC can be in any state. */
+ e1000_irq_disable(adapter);
+
+ set_bit(__E1000_DOWN, &adapter->state);
+ return 0;
+}
+
+/**
+ * e1000_intr_msi_test - Interrupt Handler
+ * @irq: interrupt number
+ * @data: pointer to a network interface device structure
+ **/
+static irqreturn_t e1000_intr_msi_test(int irq, void *data)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 icr = er32(ICR);
+
+ e_dbg("icr is %08X\n", icr);
+ if (icr & E1000_ICR_RXSEQ) {
+ adapter->flags &= ~FLAG_MSI_TEST_FAILED;
+ wmb();
+ }
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * e1000_test_msi_interrupt - Returns 0 for successful test
+ * @adapter: board private struct
+ *
+ * code flow taken from tg3.c
+ **/
+static int e1000_test_msi_interrupt(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_hw *hw = &adapter->hw;
+ int err;
+
+ /* poll_enable hasn't been called yet, so don't need disable */
+ /* clear any pending events */
+ er32(ICR);
+
+ /* free the real vector and request a test handler */
+ e1000_free_irq(adapter);
+ e1000e_reset_interrupt_capability(adapter);
+
+ /* Assume that the test fails, if it succeeds then the test
+ * MSI irq handler will unset this flag */
+ adapter->flags |= FLAG_MSI_TEST_FAILED;
+
+ err = pci_enable_msi(adapter->pdev);
+ if (err)
+ goto msi_test_failed;
+
+ err = request_irq(adapter->pdev->irq, e1000_intr_msi_test, 0,
+ netdev->name, netdev);
+ if (err) {
+ pci_disable_msi(adapter->pdev);
+ goto msi_test_failed;
+ }
+
+ wmb();
+
+ e1000_irq_enable(adapter);
+
+ /* fire an unusual interrupt on the test handler */
+ ew32(ICS, E1000_ICS_RXSEQ);
+ e1e_flush();
+ msleep(50);
+
+ e1000_irq_disable(adapter);
+
+ rmb();
+
+ if (adapter->flags & FLAG_MSI_TEST_FAILED) {
+ adapter->int_mode = E1000E_INT_MODE_LEGACY;
+ err = -EIO;
+ e_info("MSI interrupt test failed!\n");
+ }
+
+ free_irq(adapter->pdev->irq, netdev);
+ pci_disable_msi(adapter->pdev);
+
+ if (err == -EIO)
+ goto msi_test_failed;
+
+ /* okay so the test worked, restore settings */
+ e_dbg("MSI interrupt test succeeded!\n");
+msi_test_failed:
+ e1000e_set_interrupt_capability(adapter);
+ e1000_request_irq(adapter);
+ return err;
+}
+
+/**
+ * e1000_test_msi - Returns 0 if MSI test succeeds or INTx mode is restored
+ * @adapter: board private struct
+ *
+ * code flow taken from tg3.c, called with e1000 interrupts disabled.
+ **/
+static int e1000_test_msi(struct e1000_adapter *adapter)
+{
+ int err;
+ u16 pci_cmd;
+
+ if (!(adapter->flags & FLAG_MSI_ENABLED))
+ return 0;
+
+ /* disable SERR in case the MSI write causes a master abort */
+ pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd);
+ if (pci_cmd & PCI_COMMAND_SERR)
+ pci_write_config_word(adapter->pdev, PCI_COMMAND,
+ pci_cmd & ~PCI_COMMAND_SERR);
+
+ err = e1000_test_msi_interrupt(adapter);
+
+ /* re-enable SERR */
+ if (pci_cmd & PCI_COMMAND_SERR) {
+ pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd);
+ pci_cmd |= PCI_COMMAND_SERR;
+ pci_write_config_word(adapter->pdev, PCI_COMMAND, pci_cmd);
+ }
+
+ /* success ! */
+ if (!err)
+ return 0;
+
+ /* EIO means MSI test failed */
+ if (err != -EIO)
+ return err;
+
+ /* back to INTx mode */
+ e_warn("MSI interrupt test failed, using legacy interrupt.\n");
+
+ e1000_free_irq(adapter);
+
+ err = e1000_request_irq(adapter);
+
+ return err;
+}
+
+/**
+ * e1000_open - Called when a network interface is made active
+ * @netdev: network interface device structure
+ *
+ * Returns 0 on success, negative value on failure
+ *
+ * The open entry point is called when a network interface is made
+ * active by the system (IFF_UP). At this point all resources needed
+ * for transmit and receive operations are allocated, the interrupt
+ * handler is registered with the OS, the watchdog timer is started,
+ * and the stack is notified that the interface is ready.
+ **/
+static int e1000_open(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct pci_dev *pdev = adapter->pdev;
+ int err;
+
+ /* disallow open during test */
+ if (test_bit(__E1000_TESTING, &adapter->state))
+ return -EBUSY;
+
+ pm_runtime_get_sync(&pdev->dev);
+
+ if (adapter->ecdev) {
+ ecdev_set_link(adapter->ecdev, 0);
+ } else {
+ netif_carrier_off(netdev);
+ }
+
+ /* allocate transmit descriptors */
+ err = e1000e_setup_tx_resources(adapter);
+ if (err)
+ goto err_setup_tx;
+
+ /* allocate receive descriptors */
+ err = e1000e_setup_rx_resources(adapter);
+ if (err)
+ goto err_setup_rx;
+
+ /*
+ * If AMT is enabled, let the firmware know that the network
+ * interface is now open and reset the part to a known state.
+ */
+ if (adapter->flags & FLAG_HAS_AMT) {
+ e1000_get_hw_control(adapter);
+ e1000e_reset(adapter);
+ }
+
+ e1000e_power_up_phy(adapter);
+
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+ if ((adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN))
+ e1000_update_mng_vlan(adapter);
+
+ /*
+ * before we allocate an interrupt, we must be ready to handle it.
+ * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
+ * as soon as we call pci_request_irq, so we have to setup our
+ * clean_rx handler before we do so.
+ */
+ e1000_configure(adapter);
+
+ err = e1000_request_irq(adapter);
+ if (err)
+ goto err_req_irq;
+
+ /*
+ * Work around PCIe errata with MSI interrupts causing some chipsets to
+ * ignore e1000e MSI messages, which means we need to test our MSI
+ * interrupt now
+ */
+ if (adapter->int_mode != E1000E_INT_MODE_LEGACY) {
+ err = e1000_test_msi(adapter);
+ if (err) {
+ e_err("Interrupt allocation failed\n");
+ goto err_req_irq;
+ }
+ }
+
+ /* From here on the code is the same as e1000e_up() */
+ clear_bit(__E1000_DOWN, &adapter->state);
+
+ napi_enable(&adapter->napi);
+
+ e1000_irq_enable(adapter);
+
+ netif_start_queue(netdev);
+
+ adapter->idle_check = true;
+ pm_runtime_put(&pdev->dev);
+
+ /* fire a link status change interrupt to start the watchdog */
+ if (adapter->msix_entries)
+ ew32(ICS, E1000_ICS_LSC | E1000_ICR_OTHER);
+ else
+ ew32(ICS, E1000_ICS_LSC);
+
+ return 0;
+
+err_req_irq:
+ e1000_release_hw_control(adapter);
+ e1000_power_down_phy(adapter);
+ e1000e_free_rx_resources(adapter);
+err_setup_rx:
+ e1000e_free_tx_resources(adapter);
+err_setup_tx:
+ e1000e_reset(adapter);
+ pm_runtime_put_sync(&pdev->dev);
+
+ return err;
+}
+
+/**
+ * e1000_close - Disables a network interface
+ * @netdev: network interface device structure
+ *
+ * Returns 0, this is not allowed to fail
+ *
+ * The close entry point is called when an interface is de-activated
+ * by the OS. The hardware is still under the drivers control, but
+ * needs to be disabled. A global MAC reset is issued to stop the
+ * hardware, and all transmit and receive resources are freed.
+ **/
+static int e1000_close(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct pci_dev *pdev = adapter->pdev;
+
+ WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
+
+ pm_runtime_get_sync(&pdev->dev);
+
+ if (!test_bit(__E1000_DOWN, &adapter->state)) {
+ e1000e_down(adapter);
+ e1000_free_irq(adapter);
+ }
+ e1000_power_down_phy(adapter);
+
+ e1000e_free_tx_resources(adapter);
+ e1000e_free_rx_resources(adapter);
+
+ /*
+ * kill manageability vlan ID if supported, but not if a vlan with
+ * the same ID is registered on the host OS (let 8021q kill it)
+ */
+ if ((adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
+ !(adapter->vlgrp &&
+ vlan_group_get_device(adapter->vlgrp, adapter->mng_vlan_id)))
+ e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
+
+ /*
+ * If AMT is enabled, let the firmware know that the network
+ * interface is now closed
+ */
+ if (adapter->flags & FLAG_HAS_AMT)
+ e1000_release_hw_control(adapter);
+
+ pm_runtime_put_sync(&pdev->dev);
+
+ return 0;
+}
+/**
+ * e1000_set_mac - Change the Ethernet Address of the NIC
+ * @netdev: network interface device structure
+ * @p: pointer to an address structure
+ *
+ * Returns 0 on success, negative on failure
+ **/
+static int e1000_set_mac(struct net_device *netdev, void *p)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct sockaddr *addr = p;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
+ memcpy(adapter->hw.mac.addr, addr->sa_data, netdev->addr_len);
+
+ e1000e_rar_set(&adapter->hw, adapter->hw.mac.addr, 0);
+
+ if (adapter->flags & FLAG_RESET_OVERWRITES_LAA) {
+ /* activate the work around */
+ e1000e_set_laa_state_82571(&adapter->hw, 1);
+
+ /*
+ * Hold a copy of the LAA in RAR[14] This is done so that
+ * between the time RAR[0] gets clobbered and the time it
+ * gets fixed (in e1000_watchdog), the actual LAA is in one
+ * of the RARs and no incoming packets directed to this port
+ * are dropped. Eventually the LAA will be in RAR[0] and
+ * RAR[14]
+ */
+ e1000e_rar_set(&adapter->hw,
+ adapter->hw.mac.addr,
+ adapter->hw.mac.rar_entry_count - 1);
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_update_phy_task - work thread to update phy
+ * @work: pointer to our work struct
+ *
+ * this worker thread exists because we must acquire a
+ * semaphore to read the phy, which we could msleep while
+ * waiting for it, and we can't msleep in a timer.
+ **/
+static void e1000e_update_phy_task(struct work_struct *work)
+{
+ struct e1000_adapter *adapter = container_of(work,
+ struct e1000_adapter, update_phy_task);
+ e1000_get_phy_info(&adapter->hw);
+}
+
+/*
+ * Need to wait a few seconds after link up to get diagnostic information from
+ * the phy
+ */
+static void e1000_update_phy_info(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+ schedule_work(&adapter->update_phy_task);
+}
+
+/**
+ * e1000e_update_stats - Update the board statistics counters
+ * @adapter: board private structure
+ **/
+void e1000e_update_stats(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_hw *hw = &adapter->hw;
+ struct pci_dev *pdev = adapter->pdev;
+ u16 phy_data;
+
+ /*
+ * Prevent stats update while adapter is being reset, or if the pci
+ * connection is down.
+ */
+ if (adapter->link_speed == 0)
+ return;
+ if (pci_channel_offline(pdev))
+ return;
+
+ adapter->stats.crcerrs += er32(CRCERRS);
+ adapter->stats.gprc += er32(GPRC);
+ adapter->stats.gorc += er32(GORCL);
+ er32(GORCH); /* Clear gorc */
+ adapter->stats.bprc += er32(BPRC);
+ adapter->stats.mprc += er32(MPRC);
+ adapter->stats.roc += er32(ROC);
+
+ adapter->stats.mpc += er32(MPC);
+ if ((hw->phy.type == e1000_phy_82578) ||
+ (hw->phy.type == e1000_phy_82577)) {
+ e1e_rphy(hw, HV_SCC_UPPER, &phy_data);
+ if (!e1e_rphy(hw, HV_SCC_LOWER, &phy_data))
+ adapter->stats.scc += phy_data;
+
+ e1e_rphy(hw, HV_ECOL_UPPER, &phy_data);
+ if (!e1e_rphy(hw, HV_ECOL_LOWER, &phy_data))
+ adapter->stats.ecol += phy_data;
+
+ e1e_rphy(hw, HV_MCC_UPPER, &phy_data);
+ if (!e1e_rphy(hw, HV_MCC_LOWER, &phy_data))
+ adapter->stats.mcc += phy_data;
+
+ e1e_rphy(hw, HV_LATECOL_UPPER, &phy_data);
+ if (!e1e_rphy(hw, HV_LATECOL_LOWER, &phy_data))
+ adapter->stats.latecol += phy_data;
+
+ e1e_rphy(hw, HV_DC_UPPER, &phy_data);
+ if (!e1e_rphy(hw, HV_DC_LOWER, &phy_data))
+ adapter->stats.dc += phy_data;
+ } else {
+ adapter->stats.scc += er32(SCC);
+ adapter->stats.ecol += er32(ECOL);
+ adapter->stats.mcc += er32(MCC);
+ adapter->stats.latecol += er32(LATECOL);
+ adapter->stats.dc += er32(DC);
+ }
+ adapter->stats.xonrxc += er32(XONRXC);
+ adapter->stats.xontxc += er32(XONTXC);
+ adapter->stats.xoffrxc += er32(XOFFRXC);
+ adapter->stats.xofftxc += er32(XOFFTXC);
+ adapter->stats.gptc += er32(GPTC);
+ adapter->stats.gotc += er32(GOTCL);
+ er32(GOTCH); /* Clear gotc */
+ adapter->stats.rnbc += er32(RNBC);
+ adapter->stats.ruc += er32(RUC);
+
+ adapter->stats.mptc += er32(MPTC);
+ adapter->stats.bptc += er32(BPTC);
+
+ /* used for adaptive IFS */
+
+ hw->mac.tx_packet_delta = er32(TPT);
+ adapter->stats.tpt += hw->mac.tx_packet_delta;
+ if ((hw->phy.type == e1000_phy_82578) ||
+ (hw->phy.type == e1000_phy_82577)) {
+ e1e_rphy(hw, HV_COLC_UPPER, &phy_data);
+ if (!e1e_rphy(hw, HV_COLC_LOWER, &phy_data))
+ hw->mac.collision_delta = phy_data;
+ } else {
+ hw->mac.collision_delta = er32(COLC);
+ }
+ adapter->stats.colc += hw->mac.collision_delta;
+
+ adapter->stats.algnerrc += er32(ALGNERRC);
+ adapter->stats.rxerrc += er32(RXERRC);
+ if ((hw->phy.type == e1000_phy_82578) ||
+ (hw->phy.type == e1000_phy_82577)) {
+ e1e_rphy(hw, HV_TNCRS_UPPER, &phy_data);
+ if (!e1e_rphy(hw, HV_TNCRS_LOWER, &phy_data))
+ adapter->stats.tncrs += phy_data;
+ } else {
+ if ((hw->mac.type != e1000_82574) &&
+ (hw->mac.type != e1000_82583))
+ adapter->stats.tncrs += er32(TNCRS);
+ }
+ adapter->stats.cexterr += er32(CEXTERR);
+ adapter->stats.tsctc += er32(TSCTC);
+ adapter->stats.tsctfc += er32(TSCTFC);
+
+ /* Fill out the OS statistics structure */
+ netdev->stats.multicast = adapter->stats.mprc;
+ netdev->stats.collisions = adapter->stats.colc;
+
+ /* Rx Errors */
+
+ /*
+ * RLEC on some newer hardware can be incorrect so build
+ * our own version based on RUC and ROC
+ */
+ netdev->stats.rx_errors = adapter->stats.rxerrc +
+ adapter->stats.crcerrs + adapter->stats.algnerrc +
+ adapter->stats.ruc + adapter->stats.roc +
+ adapter->stats.cexterr;
+ netdev->stats.rx_length_errors = adapter->stats.ruc +
+ adapter->stats.roc;
+ netdev->stats.rx_crc_errors = adapter->stats.crcerrs;
+ netdev->stats.rx_frame_errors = adapter->stats.algnerrc;
+ netdev->stats.rx_missed_errors = adapter->stats.mpc;
+
+ /* Tx Errors */
+ netdev->stats.tx_errors = adapter->stats.ecol +
+ adapter->stats.latecol;
+ netdev->stats.tx_aborted_errors = adapter->stats.ecol;
+ netdev->stats.tx_window_errors = adapter->stats.latecol;
+ netdev->stats.tx_carrier_errors = adapter->stats.tncrs;
+
+ /* Tx Dropped needs to be maintained elsewhere */
+
+ /* Management Stats */
+ adapter->stats.mgptc += er32(MGTPTC);
+ adapter->stats.mgprc += er32(MGTPRC);
+ adapter->stats.mgpdc += er32(MGTPDC);
+}
+
+/**
+ * e1000_phy_read_status - Update the PHY register status snapshot
+ * @adapter: board private structure
+ **/
+static void e1000_phy_read_status(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_phy_regs *phy = &adapter->phy_regs;
+ int ret_val;
+
+ if ((er32(STATUS) & E1000_STATUS_LU) &&
+ (adapter->hw.phy.media_type == e1000_media_type_copper)) {
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy->bmcr);
+ ret_val |= e1e_rphy(hw, PHY_STATUS, &phy->bmsr);
+ ret_val |= e1e_rphy(hw, PHY_AUTONEG_ADV, &phy->advertise);
+ ret_val |= e1e_rphy(hw, PHY_LP_ABILITY, &phy->lpa);
+ ret_val |= e1e_rphy(hw, PHY_AUTONEG_EXP, &phy->expansion);
+ ret_val |= e1e_rphy(hw, PHY_1000T_CTRL, &phy->ctrl1000);
+ ret_val |= e1e_rphy(hw, PHY_1000T_STATUS, &phy->stat1000);
+ ret_val |= e1e_rphy(hw, PHY_EXT_STATUS, &phy->estatus);
+ if (ret_val)
+ e_warn("Error reading PHY register\n");
+ } else {
+ /*
+ * Do not read PHY registers if link is not up
+ * Set values to typical power-on defaults
+ */
+ phy->bmcr = (BMCR_SPEED1000 | BMCR_ANENABLE | BMCR_FULLDPLX);
+ phy->bmsr = (BMSR_100FULL | BMSR_100HALF | BMSR_10FULL |
+ BMSR_10HALF | BMSR_ESTATEN | BMSR_ANEGCAPABLE |
+ BMSR_ERCAP);
+ phy->advertise = (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP |
+ ADVERTISE_ALL | ADVERTISE_CSMA);
+ phy->lpa = 0;
+ phy->expansion = EXPANSION_ENABLENPAGE;
+ phy->ctrl1000 = ADVERTISE_1000FULL;
+ phy->stat1000 = 0;
+ phy->estatus = (ESTATUS_1000_TFULL | ESTATUS_1000_THALF);
+ }
+}
+
+static void e1000_print_link_info(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl = er32(CTRL);
+
+ /* Link status message must follow this format for user tools */
+ printk(KERN_INFO "e1000e: %s NIC Link is Up %d Mbps %s, "
+ "Flow Control: %s\n",
+ adapter->netdev->name,
+ adapter->link_speed,
+ (adapter->link_duplex == FULL_DUPLEX) ?
+ "Full Duplex" : "Half Duplex",
+ ((ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE)) ?
+ "RX/TX" :
+ ((ctrl & E1000_CTRL_RFCE) ? "RX" :
+ ((ctrl & E1000_CTRL_TFCE) ? "TX" : "None" )));
+}
+
+bool e1000e_has_link(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ bool link_active = 0;
+ s32 ret_val = 0;
+
+ /*
+ * get_link_status is set on LSC (link status) interrupt or
+ * Rx sequence error interrupt. get_link_status will stay
+ * false until the check_for_link establishes link
+ * for copper adapters ONLY
+ */
+ switch (hw->phy.media_type) {
+ case e1000_media_type_copper:
+ if (hw->mac.get_link_status) {
+ ret_val = hw->mac.ops.check_for_link(hw);
+ link_active = !hw->mac.get_link_status;
+ } else {
+ link_active = 1;
+ }
+ break;
+ case e1000_media_type_fiber:
+ ret_val = hw->mac.ops.check_for_link(hw);
+ link_active = !!(er32(STATUS) & E1000_STATUS_LU);
+ break;
+ case e1000_media_type_internal_serdes:
+ ret_val = hw->mac.ops.check_for_link(hw);
+ link_active = adapter->hw.mac.serdes_has_link;
+ break;
+ default:
+ case e1000_media_type_unknown:
+ break;
+ }
+
+ if ((ret_val == E1000_ERR_PHY) && (hw->phy.type == e1000_phy_igp_3) &&
+ (er32(CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) {
+ /* See e1000_kmrn_lock_loss_workaround_ich8lan() */
+ e_info("Gigabit has been disabled, downgrading speed\n");
+ }
+
+ return link_active;
+}
+
+static void e1000e_enable_receives(struct e1000_adapter *adapter)
+{
+ /* make sure the receive unit is started */
+ if ((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
+ (adapter->flags & FLAG_RX_RESTART_NOW)) {
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl = er32(RCTL);
+ ew32(RCTL, rctl | E1000_RCTL_EN);
+ adapter->flags &= ~FLAG_RX_RESTART_NOW;
+ }
+}
+
+/**
+ * e1000_watchdog - Timer Call-back
+ * @data: pointer to adapter cast into an unsigned long
+ **/
+static void e1000_watchdog(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+
+ /* Do the rest outside of interrupt context */
+ schedule_work(&adapter->watchdog_task);
+
+ /* TODO: make this use queue_delayed_work() */
+}
+
+static void e1000_watchdog_task(struct work_struct *work)
+{
+ struct e1000_adapter *adapter = container_of(work,
+ struct e1000_adapter, watchdog_task);
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_mac_info *mac = &adapter->hw.mac;
+ struct e1000_phy_info *phy = &adapter->hw.phy;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 link, tctl;
+ int tx_pending = 0;
+
+ link = e1000e_has_link(adapter);
+ if ((adapter->ecdev && (ecdev_get_link(adapter->ecdev)) && link)
+ || (!adapter->ecdev && (netif_carrier_ok(netdev)) && link)) {
+ /* Cancel scheduled suspend requests. */
+ pm_runtime_resume(netdev->dev.parent);
+
+ e1000e_enable_receives(adapter);
+ goto link_up;
+ }
+
+ if ((e1000e_enable_tx_pkt_filtering(hw)) &&
+ (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id))
+ e1000_update_mng_vlan(adapter);
+
+ if (link) {
+ if ((adapter->ecdev && !ecdev_get_link(adapter->ecdev))
+ || (!adapter->ecdev && !netif_carrier_ok(netdev))) {
+ bool txb2b = 1;
+
+ /* Cancel scheduled suspend requests. */
+ pm_runtime_resume(netdev->dev.parent);
+
+ /* update snapshot of PHY registers on LSC */
+ e1000_phy_read_status(adapter);
+ mac->ops.get_link_up_info(&adapter->hw,
+ &adapter->link_speed,
+ &adapter->link_duplex);
+ e1000_print_link_info(adapter);
+ /*
+ * On supported PHYs, check for duplex mismatch only
+ * if link has autonegotiated at 10/100 half
+ */
+ if ((hw->phy.type == e1000_phy_igp_3 ||
+ hw->phy.type == e1000_phy_bm) &&
+ (hw->mac.autoneg == true) &&
+ (adapter->link_speed == SPEED_10 ||
+ adapter->link_speed == SPEED_100) &&
+ (adapter->link_duplex == HALF_DUPLEX)) {
+ u16 autoneg_exp;
+
+ e1e_rphy(hw, PHY_AUTONEG_EXP, &autoneg_exp);
+
+ if (!(autoneg_exp & NWAY_ER_LP_NWAY_CAPS))
+ e_info("Autonegotiated half duplex but"
+ " link partner cannot autoneg. "
+ " Try forcing full duplex if "
+ "link gets many collisions.\n");
+ }
+
+ /* adjust timeout factor according to speed/duplex */
+ adapter->tx_timeout_factor = 1;
+ switch (adapter->link_speed) {
+ case SPEED_10:
+ txb2b = 0;
+ adapter->tx_timeout_factor = 16;
+ break;
+ case SPEED_100:
+ txb2b = 0;
+ adapter->tx_timeout_factor = 10;
+ break;
+ }
+
+ /*
+ * workaround: re-program speed mode bit after
+ * link-up event
+ */
+ if ((adapter->flags & FLAG_TARC_SPEED_MODE_BIT) &&
+ !txb2b) {
+ u32 tarc0;
+ tarc0 = er32(TARC(0));
+ tarc0 &= ~SPEED_MODE_BIT;
+ ew32(TARC(0), tarc0);
+ }
+
+ /*
+ * disable TSO for pcie and 10/100 speeds, to avoid
+ * some hardware issues
+ */
+ if (!(adapter->flags & FLAG_TSO_FORCE)) {
+ switch (adapter->link_speed) {
+ case SPEED_10:
+ case SPEED_100:
+ e_info("10/100 speed: disabling TSO\n");
+ netdev->features &= ~NETIF_F_TSO;
+ netdev->features &= ~NETIF_F_TSO6;
+ break;
+ case SPEED_1000:
+ netdev->features |= NETIF_F_TSO;
+ netdev->features |= NETIF_F_TSO6;
+ break;
+ default:
+ /* oops */
+ break;
+ }
+ }
+
+ /*
+ * enable transmits in the hardware, need to do this
+ * after setting TARC(0)
+ */
+ tctl = er32(TCTL);
+ tctl |= E1000_TCTL_EN;
+ ew32(TCTL, tctl);
+
+ /*
+ * Perform any post-link-up configuration before
+ * reporting link up.
+ */
+ if (phy->ops.cfg_on_link_up)
+ phy->ops.cfg_on_link_up(hw);
+
+ if (adapter->ecdev)
+ ecdev_set_link(adapter->ecdev, 1);
+ else
+ netif_carrier_on(netdev);
+
+ if (!adapter->ecdev && !test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->phy_info_timer,
+ round_jiffies(jiffies + 2 * HZ));
+ }
+ } else {
+ if ((adapter->ecdev && ecdev_get_link(adapter->ecdev))
+ || (!adapter->ecdev && netif_carrier_ok(netdev))) {
+ adapter->link_speed = 0;
+ adapter->link_duplex = 0;
+ /* Link status message must follow this format */
+ printk(KERN_INFO "e1000e: %s NIC Link is Down\n",
+ adapter->netdev->name);
+ if (adapter->ecdev)
+ ecdev_set_link(adapter->ecdev, 0);
+ else
+ netif_carrier_off(netdev);
+ if (!adapter->ecdev && !test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->phy_info_timer,
+ round_jiffies(jiffies + 2 * HZ));
+
+ if (adapter->flags & FLAG_RX_NEEDS_RESTART)
+ schedule_work(&adapter->reset_task);
+ else
+ pm_schedule_suspend(netdev->dev.parent,
+ LINK_TIMEOUT);
+ }
+ }
+
+link_up:
+ e1000e_update_stats(adapter);
+
+ mac->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old;
+ adapter->tpt_old = adapter->stats.tpt;
+ mac->collision_delta = adapter->stats.colc - adapter->colc_old;
+ adapter->colc_old = adapter->stats.colc;
+
+ adapter->gorc = adapter->stats.gorc - adapter->gorc_old;
+ adapter->gorc_old = adapter->stats.gorc;
+ adapter->gotc = adapter->stats.gotc - adapter->gotc_old;
+ adapter->gotc_old = adapter->stats.gotc;
+
+ e1000e_update_adaptive(&adapter->hw);
+
+ if ((adapter->ecdev && !ecdev_get_link(adapter->ecdev))
+ || (!adapter->ecdev && !netif_carrier_ok(netdev))) {
+ tx_pending = (e1000_desc_unused(tx_ring) + 1 <
+ tx_ring->count);
+ if (tx_pending) {
+ /*
+ * We've lost link, so the controller stops DMA,
+ * but we've got queued Tx work that's never going
+ * to get done, so reset controller to flush Tx.
+ * (Do the reset outside of interrupt context).
+ */
+ adapter->tx_timeout_count++;
+ schedule_work(&adapter->reset_task);
+ /* return immediately since reset is imminent */
+ return;
+ }
+ }
+
+ /* Simple mode for Interrupt Throttle Rate (ITR) */
+ if (adapter->itr_setting == 4) {
+ /*
+ * Symmetric Tx/Rx gets a reduced ITR=2000;
+ * Total asymmetrical Tx or Rx gets ITR=8000;
+ * everyone else is between 2000-8000.
+ */
+ u32 goc = (adapter->gotc + adapter->gorc) / 10000;
+ u32 dif = (adapter->gotc > adapter->gorc ?
+ adapter->gotc - adapter->gorc :
+ adapter->gorc - adapter->gotc) / 10000;
+ u32 itr = goc > 0 ? (dif * 6000 / goc + 2000) : 8000;
+
+ ew32(ITR, 1000000000 / (itr * 256));
+ }
+
+ /* Cause software interrupt to ensure Rx ring is cleaned */
+ if (adapter->msix_entries)
+ ew32(ICS, adapter->rx_ring->ims_val);
+ else
+ ew32(ICS, E1000_ICS_RXDMT0);
+
+ /* Force detection of hung controller every watchdog period */
+ adapter->detect_tx_hung = 1;
+
+ /*
+ * With 82571 controllers, LAA may be overwritten due to controller
+ * reset from the other port. Set the appropriate LAA in RAR[0]
+ */
+ if (e1000e_get_laa_state_82571(hw))
+ e1000e_rar_set(hw, adapter->hw.mac.addr, 0);
+
+ /* Reset the timer */
+ if (!adapter->ecdev && !test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->watchdog_timer,
+ round_jiffies(jiffies + 2 * HZ));
+}
+
+#define E1000_TX_FLAGS_CSUM 0x00000001
+#define E1000_TX_FLAGS_VLAN 0x00000002
+#define E1000_TX_FLAGS_TSO 0x00000004
+#define E1000_TX_FLAGS_IPV4 0x00000008
+#define E1000_TX_FLAGS_VLAN_MASK 0xffff0000
+#define E1000_TX_FLAGS_VLAN_SHIFT 16
+
+static int e1000_tso(struct e1000_adapter *adapter,
+ struct sk_buff *skb)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_context_desc *context_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i;
+ u32 cmd_length = 0;
+ u16 ipcse = 0, tucse, mss;
+ u8 ipcss, ipcso, tucss, tucso, hdr_len;
+ int err;
+
+ if (!skb_is_gso(skb))
+ return 0;
+
+ if (skb_header_cloned(skb)) {
+ err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
+ if (err)
+ return err;
+ }
+
+ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ mss = skb_shinfo(skb)->gso_size;
+ if (skb->protocol == htons(ETH_P_IP)) {
+ struct iphdr *iph = ip_hdr(skb);
+ iph->tot_len = 0;
+ iph->check = 0;
+ tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr, iph->daddr,
+ 0, IPPROTO_TCP, 0);
+ cmd_length = E1000_TXD_CMD_IP;
+ ipcse = skb_transport_offset(skb) - 1;
+ } else if (skb_is_gso_v6(skb)) {
+ ipv6_hdr(skb)->payload_len = 0;
+ tcp_hdr(skb)->check = ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
+ &ipv6_hdr(skb)->daddr,
+ 0, IPPROTO_TCP, 0);
+ ipcse = 0;
+ }
+ ipcss = skb_network_offset(skb);
+ ipcso = (void *)&(ip_hdr(skb)->check) - (void *)skb->data;
+ tucss = skb_transport_offset(skb);
+ tucso = (void *)&(tcp_hdr(skb)->check) - (void *)skb->data;
+ tucse = 0;
+
+ cmd_length |= (E1000_TXD_CMD_DEXT | E1000_TXD_CMD_TSE |
+ E1000_TXD_CMD_TCP | (skb->len - (hdr_len)));
+
+ i = tx_ring->next_to_use;
+ context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
+ buffer_info = &tx_ring->buffer_info[i];
+
+ context_desc->lower_setup.ip_fields.ipcss = ipcss;
+ context_desc->lower_setup.ip_fields.ipcso = ipcso;
+ context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse);
+ context_desc->upper_setup.tcp_fields.tucss = tucss;
+ context_desc->upper_setup.tcp_fields.tucso = tucso;
+ context_desc->upper_setup.tcp_fields.tucse = cpu_to_le16(tucse);
+ context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss);
+ context_desc->tcp_seg_setup.fields.hdr_len = hdr_len;
+ context_desc->cmd_and_length = cpu_to_le32(cmd_length);
+
+ buffer_info->time_stamp = jiffies;
+ buffer_info->next_to_watch = i;
+
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+ tx_ring->next_to_use = i;
+
+ return 1;
+}
+
+static bool e1000_tx_csum(struct e1000_adapter *adapter, struct sk_buff *skb)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_context_desc *context_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i;
+ u8 css;
+ u32 cmd_len = E1000_TXD_CMD_DEXT;
+ __be16 protocol;
+
+ if (skb->ip_summed != CHECKSUM_PARTIAL)
+ return 0;
+
+ if (skb->protocol == cpu_to_be16(ETH_P_8021Q))
+ protocol = vlan_eth_hdr(skb)->h_vlan_encapsulated_proto;
+ else
+ protocol = skb->protocol;
+
+ switch (protocol) {
+ case cpu_to_be16(ETH_P_IP):
+ if (ip_hdr(skb)->protocol == IPPROTO_TCP)
+ cmd_len |= E1000_TXD_CMD_TCP;
+ break;
+ case cpu_to_be16(ETH_P_IPV6):
+ /* XXX not handling all IPV6 headers */
+ if (ipv6_hdr(skb)->nexthdr == IPPROTO_TCP)
+ cmd_len |= E1000_TXD_CMD_TCP;
+ break;
+ default:
+ if (unlikely(net_ratelimit()))
+ e_warn("checksum_partial proto=%x!\n",
+ be16_to_cpu(protocol));
+ break;
+ }
+
+ css = skb_transport_offset(skb);
+
+ i = tx_ring->next_to_use;
+ buffer_info = &tx_ring->buffer_info[i];
+ context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
+
+ context_desc->lower_setup.ip_config = 0;
+ context_desc->upper_setup.tcp_fields.tucss = css;
+ context_desc->upper_setup.tcp_fields.tucso =
+ css + skb->csum_offset;
+ context_desc->upper_setup.tcp_fields.tucse = 0;
+ context_desc->tcp_seg_setup.data = 0;
+ context_desc->cmd_and_length = cpu_to_le32(cmd_len);
+
+ buffer_info->time_stamp = jiffies;
+ buffer_info->next_to_watch = i;
+
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+ tx_ring->next_to_use = i;
+
+ return 1;
+}
+
+#define E1000_MAX_PER_TXD 8192
+#define E1000_MAX_TXD_PWR 12
+
+static int e1000_tx_map(struct e1000_adapter *adapter,
+ struct sk_buff *skb, unsigned int first,
+ unsigned int max_per_txd, unsigned int nr_frags,
+ unsigned int mss)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_buffer *buffer_info;
+ unsigned int len = skb_headlen(skb);
+ unsigned int offset = 0, size, count = 0, i;
+ unsigned int f, bytecount, segs;
+
+ i = tx_ring->next_to_use;
+
+ while (len) {
+ buffer_info = &tx_ring->buffer_info[i];
+ size = min(len, max_per_txd);
+
+ buffer_info->length = size;
+ buffer_info->time_stamp = jiffies;
+ buffer_info->next_to_watch = i;
+ buffer_info->dma = dma_map_single(&pdev->dev,
+ skb->data + offset,
+ size, DMA_TO_DEVICE);
+ buffer_info->mapped_as_page = false;
+ if (dma_mapping_error(&pdev->dev, buffer_info->dma))
+ goto dma_error;
+
+ len -= size;
+ offset += size;
+ count++;
+
+ if (len) {
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+ }
+ }
+
+ for (f = 0; f < nr_frags; f++) {
+ struct skb_frag_struct *frag;
+
+ frag = &skb_shinfo(skb)->frags[f];
+ len = frag->size;
+ offset = frag->page_offset;
+
+ while (len) {
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+
+ buffer_info = &tx_ring->buffer_info[i];
+ size = min(len, max_per_txd);
+
+ buffer_info->length = size;
+ buffer_info->time_stamp = jiffies;
+ buffer_info->next_to_watch = i;
+ buffer_info->dma = dma_map_page(&pdev->dev, frag->page,
+ offset, size,
+ DMA_TO_DEVICE);
+ buffer_info->mapped_as_page = true;
+ if (dma_mapping_error(&pdev->dev, buffer_info->dma))
+ goto dma_error;
+
+ len -= size;
+ offset += size;
+ count++;
+ }
+ }
+
+ segs = skb_shinfo(skb)->gso_segs ?: 1;
+ /* multiply data chunks by size of headers */
+ bytecount = ((segs - 1) * skb_headlen(skb)) + skb->len;
+
+ tx_ring->buffer_info[i].skb = skb;
+ tx_ring->buffer_info[i].segs = segs;
+ tx_ring->buffer_info[i].bytecount = bytecount;
+ tx_ring->buffer_info[first].next_to_watch = i;
+
+ return count;
+
+dma_error:
+ dev_err(&pdev->dev, "TX DMA map failed\n");
+ buffer_info->dma = 0;
+ if (count)
+ count--;
+
+ while (count--) {
+ if (i==0)
+ i += tx_ring->count;
+ i--;
+ buffer_info = &tx_ring->buffer_info[i];
+ e1000_put_txbuf(adapter, buffer_info);;
+ }
+
+ return 0;
+}
+
+static void e1000_tx_queue(struct e1000_adapter *adapter,
+ int tx_flags, int count)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_tx_desc *tx_desc = NULL;
+ struct e1000_buffer *buffer_info;
+ u32 txd_upper = 0, txd_lower = E1000_TXD_CMD_IFCS;
+ unsigned int i;
+
+ if (tx_flags & E1000_TX_FLAGS_TSO) {
+ txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D |
+ E1000_TXD_CMD_TSE;
+ txd_upper |= E1000_TXD_POPTS_TXSM << 8;
+
+ if (tx_flags & E1000_TX_FLAGS_IPV4)
+ txd_upper |= E1000_TXD_POPTS_IXSM << 8;
+ }
+
+ if (tx_flags & E1000_TX_FLAGS_CSUM) {
+ txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
+ txd_upper |= E1000_TXD_POPTS_TXSM << 8;
+ }
+
+ if (tx_flags & E1000_TX_FLAGS_VLAN) {
+ txd_lower |= E1000_TXD_CMD_VLE;
+ txd_upper |= (tx_flags & E1000_TX_FLAGS_VLAN_MASK);
+ }
+
+ i = tx_ring->next_to_use;
+
+ while (count--) {
+ buffer_info = &tx_ring->buffer_info[i];
+ tx_desc = E1000_TX_DESC(*tx_ring, i);
+ tx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+ tx_desc->lower.data =
+ cpu_to_le32(txd_lower | buffer_info->length);
+ tx_desc->upper.data = cpu_to_le32(txd_upper);
+
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+ }
+
+ tx_desc->lower.data |= cpu_to_le32(adapter->txd_cmd);
+
+ /*
+ * Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64).
+ */
+ wmb();
+
+ tx_ring->next_to_use = i;
+ writel(i, adapter->hw.hw_addr + tx_ring->tail);
+ /*
+ * we need this if more than one processor can write to our tail
+ * at a time, it synchronizes IO on IA64/Altix systems
+ */
+ mmiowb();
+}
+
+#define MINIMUM_DHCP_PACKET_SIZE 282
+static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter,
+ struct sk_buff *skb)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 length, offset;
+
+ if (vlan_tx_tag_present(skb)) {
+ if (!((vlan_tx_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) &&
+ (adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN)))
+ return 0;
+ }
+
+ if (skb->len <= MINIMUM_DHCP_PACKET_SIZE)
+ return 0;
+
+ if (((struct ethhdr *) skb->data)->h_proto != htons(ETH_P_IP))
+ return 0;
+
+ {
+ const struct iphdr *ip = (struct iphdr *)((u8 *)skb->data+14);
+ struct udphdr *udp;
+
+ if (ip->protocol != IPPROTO_UDP)
+ return 0;
+
+ udp = (struct udphdr *)((u8 *)ip + (ip->ihl << 2));
+ if (ntohs(udp->dest) != 67)
+ return 0;
+
+ offset = (u8 *)udp + 8 - skb->data;
+ length = skb->len - offset;
+ return e1000e_mng_write_dhcp_info(hw, (u8 *)udp + 8, length);
+ }
+
+ return 0;
+}
+
+static int __e1000_maybe_stop_tx(struct net_device *netdev, int size)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ netif_stop_queue(netdev);
+ /*
+ * Herbert's original patch had:
+ * smp_mb__after_netif_stop_queue();
+ * but since that doesn't exist yet, just open code it.
+ */
+ smp_mb();
+
+ /*
+ * We need to check again in a case another CPU has just
+ * made room available.
+ */
+ if (e1000_desc_unused(adapter->tx_ring) < size)
+ return -EBUSY;
+
+ /* A reprieve! */
+ netif_start_queue(netdev);
+ ++adapter->restart_queue;
+ return 0;
+}
+
+static int e1000_maybe_stop_tx(struct net_device *netdev, int size)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (e1000_desc_unused(adapter->tx_ring) >= size)
+ return 0;
+ return __e1000_maybe_stop_tx(netdev, size);
+}
+
+#define TXD_USE_COUNT(S, X) (((S) >> (X)) + 1 )
+static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
+ struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ unsigned int first;
+ unsigned int max_per_txd = E1000_MAX_PER_TXD;
+ unsigned int max_txd_pwr = E1000_MAX_TXD_PWR;
+ unsigned int tx_flags = 0;
+ unsigned int len = skb_headlen(skb);
+ unsigned int nr_frags;
+ unsigned int mss;
+ int count = 0;
+ int tso;
+ unsigned int f;
+
+ if (test_bit(__E1000_DOWN, &adapter->state)) {
+ if (!adapter->ecdev)
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
+ if (skb->len <= 0) {
+ if (!adapter->ecdev)
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
+ mss = skb_shinfo(skb)->gso_size;
+ /*
+ * The controller does a simple calculation to
+ * make sure there is enough room in the FIFO before
+ * initiating the DMA for each buffer. The calc is:
+ * 4 = ceil(buffer len/mss). To make sure we don't
+ * overrun the FIFO, adjust the max buffer len if mss
+ * drops.
+ */
+ if (mss) {
+ u8 hdr_len;
+ max_per_txd = min(mss << 2, max_per_txd);
+ max_txd_pwr = fls(max_per_txd) - 1;
+
+ /*
+ * TSO Workaround for 82571/2/3 Controllers -- if skb->data
+ * points to just header, pull a few bytes of payload from
+ * frags into skb->data
+ */
+ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ /*
+ * we do this workaround for ES2LAN, but it is un-necessary,
+ * avoiding it could save a lot of cycles
+ */
+ if (skb->data_len && (hdr_len == len)) {
+ unsigned int pull_size;
+
+ pull_size = min((unsigned int)4, skb->data_len);
+ if (!__pskb_pull_tail(skb, pull_size)) {
+ e_err("__pskb_pull_tail failed.\n");
+ if (!adapter->ecdev)
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+ len = skb_headlen(skb);
+ }
+ }
+
+ /* reserve a descriptor for the offload context */
+ if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
+ count++;
+ count++;
+
+ count += TXD_USE_COUNT(len, max_txd_pwr);
+
+ nr_frags = skb_shinfo(skb)->nr_frags;
+ for (f = 0; f < nr_frags; f++)
+ count += TXD_USE_COUNT(skb_shinfo(skb)->frags[f].size,
+ max_txd_pwr);
+
+ if (adapter->hw.mac.tx_pkt_filtering)
+ e1000_transfer_dhcp_info(adapter, skb);
+
+ /*
+ * need: count + 2 desc gap to keep tail from touching
+ * head, otherwise try next time
+ */
+ if (!adapter->ecdev && e1000_maybe_stop_tx(netdev, count + 2))
+ return NETDEV_TX_BUSY;
+
+ if (adapter->vlgrp && vlan_tx_tag_present(skb)) {
+ tx_flags |= E1000_TX_FLAGS_VLAN;
+ tx_flags |= (vlan_tx_tag_get(skb) << E1000_TX_FLAGS_VLAN_SHIFT);
+ }
+
+ first = tx_ring->next_to_use;
+
+ tso = e1000_tso(adapter, skb);
+ if (tso < 0) {
+ if (!adapter->ecdev)
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
+ if (tso)
+ tx_flags |= E1000_TX_FLAGS_TSO;
+ else if (e1000_tx_csum(adapter, skb))
+ tx_flags |= E1000_TX_FLAGS_CSUM;
+
+ /*
+ * Old method was to assume IPv4 packet by default if TSO was enabled.
+ * 82571 hardware supports TSO capabilities for IPv6 as well...
+ * no longer assume, we must.
+ */
+ if (skb->protocol == htons(ETH_P_IP))
+ tx_flags |= E1000_TX_FLAGS_IPV4;
+
+ /* if count is 0 then mapping error has occured */
+ count = e1000_tx_map(adapter, skb, first, max_per_txd, nr_frags, mss);
+ if (count) {
+ e1000_tx_queue(adapter, tx_flags, count);
+ /* Make sure there is space in the ring for the next send. */
+ if (!adapter->ecdev)
+ e1000_maybe_stop_tx(netdev, MAX_SKB_FRAGS + 2);
+
+ } else {
+ if (!adapter->ecdev)
+ dev_kfree_skb_any(skb);
+ tx_ring->buffer_info[first].time_stamp = 0;
+ tx_ring->next_to_use = first;
+ }
+
+ return NETDEV_TX_OK;
+}
+
+/**
+ * e1000_tx_timeout - Respond to a Tx Hang
+ * @netdev: network interface device structure
+ **/
+static void e1000_tx_timeout(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ /* Do the reset outside of interrupt context */
+ adapter->tx_timeout_count++;
+ schedule_work(&adapter->reset_task);
+}
+
+static void e1000_reset_task(struct work_struct *work)
+{
+ struct e1000_adapter *adapter;
+ adapter = container_of(work, struct e1000_adapter, reset_task);
+
+ e1000e_dump(adapter);
+ e_err("Reset adapter\n");
+ e1000e_reinit_locked(adapter);
+}
+
+/**
+ * e1000_get_stats - Get System Network Statistics
+ * @netdev: network interface device structure
+ *
+ * Returns the address of the device statistics structure.
+ * The statistics are actually updated from the timer callback.
+ **/
+static struct net_device_stats *e1000_get_stats(struct net_device *netdev)
+{
+ /* only return the current stats */
+ return &netdev->stats;
+}
+
+/**
+ * e1000_change_mtu - Change the Maximum Transfer Unit
+ * @netdev: network interface device structure
+ * @new_mtu: new value for maximum frame size
+ *
+ * Returns 0 on success, negative on failure
+ **/
+static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
+
+ if (adapter->ecdev)
+ return -EBUSY;
+
+ /* Jumbo frame support */
+ if ((max_frame > ETH_FRAME_LEN + ETH_FCS_LEN) &&
+ !(adapter->flags & FLAG_HAS_JUMBO_FRAMES)) {
+ e_err("Jumbo Frames not supported.\n");
+ return -EINVAL;
+ }
+
+ /* Supported frame sizes */
+ if ((new_mtu < ETH_ZLEN + ETH_FCS_LEN + VLAN_HLEN) ||
+ (max_frame > adapter->max_hw_frame_size)) {
+ e_err("Unsupported MTU setting\n");
+ return -EINVAL;
+ }
+
+ /* 82573 Errata 17 */
+ if (((adapter->hw.mac.type == e1000_82573) ||
+ (adapter->hw.mac.type == e1000_82574)) &&
+ (max_frame > ETH_FRAME_LEN + ETH_FCS_LEN)) {
+ adapter->flags2 |= FLAG2_DISABLE_ASPM_L1;
+ e1000e_disable_aspm(adapter->pdev, PCIE_LINK_STATE_L1);
+ }
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
+ msleep(1);
+ /* e1000e_down -> e1000e_reset dependent on max_frame_size & mtu */
+ adapter->max_frame_size = max_frame;
+ e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu);
+ netdev->mtu = new_mtu;
+ if (netif_running(netdev))
+ e1000e_down(adapter);
+
+ /*
+ * NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
+ * means we reserve 2 more, this pushes us to allocate from the next
+ * larger slab size.
+ * i.e. RXBUFFER_2048 --> size-4096 slab
+ * However with the new *_jumbo_rx* routines, jumbo receives will use
+ * fragmented skbs
+ */
+
+ if (max_frame <= 2048)
+ adapter->rx_buffer_len = 2048;
+ else
+ adapter->rx_buffer_len = 4096;
+
+ /* adjust allocation if LPE protects us, and we aren't using SBP */
+ if ((max_frame == ETH_FRAME_LEN + ETH_FCS_LEN) ||
+ (max_frame == ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN))
+ adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN
+ + ETH_FCS_LEN;
+
+ if (netif_running(netdev))
+ e1000e_up(adapter);
+ else
+ e1000e_reset(adapter);
+
+ clear_bit(__E1000_RESETTING, &adapter->state);
+
+ return 0;
+}
+
+static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
+ int cmd)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct mii_ioctl_data *data = if_mii(ifr);
+
+ if (adapter->hw.phy.media_type != e1000_media_type_copper)
+ return -EOPNOTSUPP;
+
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ data->phy_id = adapter->hw.phy.addr;
+ break;
+ case SIOCGMIIREG:
+ e1000_phy_read_status(adapter);
+
+ switch (data->reg_num & 0x1F) {
+ case MII_BMCR:
+ data->val_out = adapter->phy_regs.bmcr;
+ break;
+ case MII_BMSR:
+ data->val_out = adapter->phy_regs.bmsr;
+ break;
+ case MII_PHYSID1:
+ data->val_out = (adapter->hw.phy.id >> 16);
+ break;
+ case MII_PHYSID2:
+ data->val_out = (adapter->hw.phy.id & 0xFFFF);
+ break;
+ case MII_ADVERTISE:
+ data->val_out = adapter->phy_regs.advertise;
+ break;
+ case MII_LPA:
+ data->val_out = adapter->phy_regs.lpa;
+ break;
+ case MII_EXPANSION:
+ data->val_out = adapter->phy_regs.expansion;
+ break;
+ case MII_CTRL1000:
+ data->val_out = adapter->phy_regs.ctrl1000;
+ break;
+ case MII_STAT1000:
+ data->val_out = adapter->phy_regs.stat1000;
+ break;
+ case MII_ESTATUS:
+ data->val_out = adapter->phy_regs.estatus;
+ break;
+ default:
+ return -EIO;
+ }
+ break;
+ case SIOCSMIIREG:
+ default:
+ return -EOPNOTSUPP;
+ }
+ return 0;
+}
+
+static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
+{
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ case SIOCGMIIREG:
+ case SIOCSMIIREG:
+ return e1000_mii_ioctl(netdev, ifr, cmd);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 i, mac_reg;
+ u16 phy_reg;
+ int retval = 0;
+
+ /* copy MAC RARs to PHY RARs */
+ for (i = 0; i < adapter->hw.mac.rar_entry_count; i++) {
+ mac_reg = er32(RAL(i));
+ e1e_wphy(hw, BM_RAR_L(i), (u16)(mac_reg & 0xFFFF));
+ e1e_wphy(hw, BM_RAR_M(i), (u16)((mac_reg >> 16) & 0xFFFF));
+ mac_reg = er32(RAH(i));
+ e1e_wphy(hw, BM_RAR_H(i), (u16)(mac_reg & 0xFFFF));
+ e1e_wphy(hw, BM_RAR_CTRL(i), (u16)((mac_reg >> 16) & 0xFFFF));
+ }
+
+ /* copy MAC MTA to PHY MTA */
+ for (i = 0; i < adapter->hw.mac.mta_reg_count; i++) {
+ mac_reg = E1000_READ_REG_ARRAY(hw, E1000_MTA, i);
+ e1e_wphy(hw, BM_MTA(i), (u16)(mac_reg & 0xFFFF));
+ e1e_wphy(hw, BM_MTA(i) + 1, (u16)((mac_reg >> 16) & 0xFFFF));
+ }
+
+ /* configure PHY Rx Control register */
+ e1e_rphy(&adapter->hw, BM_RCTL, &phy_reg);
+ mac_reg = er32(RCTL);
+ if (mac_reg & E1000_RCTL_UPE)
+ phy_reg |= BM_RCTL_UPE;
+ if (mac_reg & E1000_RCTL_MPE)
+ phy_reg |= BM_RCTL_MPE;
+ phy_reg &= ~(BM_RCTL_MO_MASK);
+ if (mac_reg & E1000_RCTL_MO_3)
+ phy_reg |= (((mac_reg & E1000_RCTL_MO_3) >> E1000_RCTL_MO_SHIFT)
+ << BM_RCTL_MO_SHIFT);
+ if (mac_reg & E1000_RCTL_BAM)
+ phy_reg |= BM_RCTL_BAM;
+ if (mac_reg & E1000_RCTL_PMCF)
+ phy_reg |= BM_RCTL_PMCF;
+ mac_reg = er32(CTRL);
+ if (mac_reg & E1000_CTRL_RFCE)
+ phy_reg |= BM_RCTL_RFCE;
+ e1e_wphy(&adapter->hw, BM_RCTL, phy_reg);
+
+ /* enable PHY wakeup in MAC register */
+ ew32(WUFC, wufc);
+ ew32(WUC, E1000_WUC_PHY_WAKE | E1000_WUC_PME_EN);
+
+ /* configure and enable PHY wakeup in PHY registers */
+ e1e_wphy(&adapter->hw, BM_WUFC, wufc);
+ e1e_wphy(&adapter->hw, BM_WUC, E1000_WUC_PME_EN);
+
+ /* activate PHY wakeup */
+ retval = hw->phy.ops.acquire(hw);
+ if (retval) {
+ e_err("Could not acquire PHY\n");
+ return retval;
+ }
+ e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+ retval = e1000e_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, &phy_reg);
+ if (retval) {
+ e_err("Could not read PHY page 769\n");
+ goto out;
+ }
+ phy_reg |= BM_WUC_ENABLE_BIT | BM_WUC_HOST_WU_BIT;
+ retval = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+ if (retval)
+ e_err("Could not set PHY Host Wakeup bit\n");
+out:
+ hw->phy.ops.release(hw);
+
+ return retval;
+}
+
+static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake,
+ bool runtime)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl, ctrl_ext, rctl, status;
+ /* Runtime suspend should only enable wakeup for link changes */
+ u32 wufc = runtime ? E1000_WUFC_LNKC : adapter->wol;
+ int retval = 0;
+
+ netif_device_detach(netdev);
+
+ if (netif_running(netdev)) {
+ WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
+ e1000e_down(adapter);
+ e1000_free_irq(adapter);
+ }
+ e1000e_reset_interrupt_capability(adapter);
+
+ retval = pci_save_state(pdev);
+ if (retval)
+ return retval;
+
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU)
+ wufc &= ~E1000_WUFC_LNKC;
+
+ if (wufc) {
+ e1000_setup_rctl(adapter);
+ e1000_set_multi(netdev);
+
+ /* turn on all-multi mode if wake on multicast is enabled */
+ if (wufc & E1000_WUFC_MC) {
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_MPE;
+ ew32(RCTL, rctl);
+ }
+
+ ctrl = er32(CTRL);
+ /* advertise wake from D3Cold */
+ #define E1000_CTRL_ADVD3WUC 0x00100000
+ /* phy power management enable */
+ #define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000
+ ctrl |= E1000_CTRL_ADVD3WUC;
+ if (!(adapter->flags2 & FLAG2_HAS_PHY_WAKEUP))
+ ctrl |= E1000_CTRL_EN_PHY_PWR_MGMT;
+ ew32(CTRL, ctrl);
+
+ if (adapter->hw.phy.media_type == e1000_media_type_fiber ||
+ adapter->hw.phy.media_type ==
+ e1000_media_type_internal_serdes) {
+ /* keep the laser running in D3 */
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_SDP3_DATA;
+ ew32(CTRL_EXT, ctrl_ext);
+ }
+
+ if (adapter->flags & FLAG_IS_ICH)
+ e1000e_disable_gig_wol_ich8lan(&adapter->hw);
+
+ /* Allow time for pending master requests to run */
+ e1000e_disable_pcie_master(&adapter->hw);
+
+ if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) {
+ /* enable wakeup by the PHY */
+ retval = e1000_init_phy_wakeup(adapter, wufc);
+ if (retval)
+ return retval;
+ } else {
+ /* enable wakeup by the MAC */
+ ew32(WUFC, wufc);
+ ew32(WUC, E1000_WUC_PME_EN);
+ }
+ } else {
+ ew32(WUC, 0);
+ ew32(WUFC, 0);
+ }
+
+ *enable_wake = !!wufc;
+
+ /* make sure adapter isn't asleep if manageability is enabled */
+ if ((adapter->flags & FLAG_MNG_PT_ENABLED) ||
+ (hw->mac.ops.check_mng_mode(hw)))
+ *enable_wake = true;
+
+ if (adapter->hw.phy.type == e1000_phy_igp_3)
+ e1000e_igp3_phy_powerdown_workaround_ich8lan(&adapter->hw);
+
+ /*
+ * Release control of h/w to f/w. If f/w is AMT enabled, this
+ * would have already happened in close and is redundant.
+ */
+ e1000_release_hw_control(adapter);
+
+ pci_disable_device(pdev);
+
+ return 0;
+}
+
+static void e1000_power_off(struct pci_dev *pdev, bool sleep, bool wake)
+{
+ if (sleep && wake) {
+ pci_prepare_to_sleep(pdev);
+ return;
+ }
+
+ pci_wake_from_d3(pdev, wake);
+ pci_set_power_state(pdev, PCI_D3hot);
+}
+
+static void e1000_complete_shutdown(struct pci_dev *pdev, bool sleep,
+ bool wake)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ /*
+ * The pci-e switch on some quad port adapters will report a
+ * correctable error when the MAC transitions from D0 to D3. To
+ * prevent this we need to mask off the correctable errors on the
+ * downstream port of the pci-e switch.
+ */
+ if (adapter->flags & FLAG_IS_QUAD_PORT) {
+ struct pci_dev *us_dev = pdev->bus->self;
+ int pos = pci_find_capability(us_dev, PCI_CAP_ID_EXP);
+ u16 devctl;
+
+ pci_read_config_word(us_dev, pos + PCI_EXP_DEVCTL, &devctl);
+ pci_write_config_word(us_dev, pos + PCI_EXP_DEVCTL,
+ (devctl & ~PCI_EXP_DEVCTL_CERE));
+
+ e1000_power_off(pdev, sleep, wake);
+
+ pci_write_config_word(us_dev, pos + PCI_EXP_DEVCTL, devctl);
+ } else {
+ e1000_power_off(pdev, sleep, wake);
+ }
+}
+
+#ifdef CONFIG_PCIEASPM
+static void __e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
+{
+ pci_disable_link_state(pdev, state);
+}
+#else
+static void __e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
+{
+ int pos;
+ u16 reg16;
+
+ /*
+ * Both device and parent should have the same ASPM setting.
+ * Disable ASPM in downstream component first and then upstream.
+ */
+ pos = pci_pcie_cap(pdev);
+ pci_read_config_word(pdev, pos + PCI_EXP_LNKCTL, ®16);
+ reg16 &= ~state;
+ pci_write_config_word(pdev, pos + PCI_EXP_LNKCTL, reg16);
+
+ if (!pdev->bus->self)
+ return;
+
+ pos = pci_pcie_cap(pdev->bus->self);
+ pci_read_config_word(pdev->bus->self, pos + PCI_EXP_LNKCTL, ®16);
+ reg16 &= ~state;
+ pci_write_config_word(pdev->bus->self, pos + PCI_EXP_LNKCTL, reg16);
+}
+#endif
+void e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
+{
+ dev_info(&pdev->dev, "Disabling ASPM %s %s\n",
+ (state & PCIE_LINK_STATE_L0S) ? "L0s" : "",
+ (state & PCIE_LINK_STATE_L1) ? "L1" : "");
+
+ __e1000e_disable_aspm(pdev, state);
+}
+
+#ifdef CONFIG_PM_OPS
+static bool e1000e_pm_ready(struct e1000_adapter *adapter)
+{
+ return !!adapter->tx_ring->buffer_info;
+}
+
+static int __e1000_resume(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 err;
+
+ if (adapter->ecdev)
+ return -EBUSY;
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+ pci_save_state(pdev);
+ if (adapter->flags2 & FLAG2_DISABLE_ASPM_L1)
+ e1000e_disable_aspm(pdev, PCIE_LINK_STATE_L1);
+
+ e1000e_set_interrupt_capability(adapter);
+ if (netif_running(netdev)) {
+ err = e1000_request_irq(adapter);
+ if (err)
+ return err;
+ }
+
+ e1000e_power_up_phy(adapter);
+
+ /* report the system wakeup cause from S3/S4 */
+ if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) {
+ u16 phy_data;
+
+ e1e_rphy(&adapter->hw, BM_WUS, &phy_data);
+ if (phy_data) {
+ e_info("PHY Wakeup cause - %s\n",
+ phy_data & E1000_WUS_EX ? "Unicast Packet" :
+ phy_data & E1000_WUS_MC ? "Multicast Packet" :
+ phy_data & E1000_WUS_BC ? "Broadcast Packet" :
+ phy_data & E1000_WUS_MAG ? "Magic Packet" :
+ phy_data & E1000_WUS_LNKC ? "Link Status "
+ " Change" : "other");
+ }
+ e1e_wphy(&adapter->hw, BM_WUS, ~0);
+ } else {
+ u32 wus = er32(WUS);
+ if (wus) {
+ e_info("MAC Wakeup cause - %s\n",
+ wus & E1000_WUS_EX ? "Unicast Packet" :
+ wus & E1000_WUS_MC ? "Multicast Packet" :
+ wus & E1000_WUS_BC ? "Broadcast Packet" :
+ wus & E1000_WUS_MAG ? "Magic Packet" :
+ wus & E1000_WUS_LNKC ? "Link Status Change" :
+ "other");
+ }
+ ew32(WUS, ~0);
+ }
+
+ e1000e_reset(adapter);
+
+ e1000_init_manageability_pt(adapter);
+
+ if (netif_running(netdev))
+ e1000e_up(adapter);
+
+ netif_device_attach(netdev);
+
+ /*
+ * If the controller has AMT, do not set DRV_LOAD until the interface
+ * is up. For all other cases, let the f/w know that the h/w is now
+ * under the control of the driver.
+ */
+ if (!(adapter->flags & FLAG_HAS_AMT))
+ e1000_get_hw_control(adapter);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int e1000_suspend(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ int retval;
+ bool wake;
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (adapter->ecdev) {
+ return -EBUSY;
+ }
+
+ retval = __e1000_shutdown(pdev, &wake, false);
+ if (!retval)
+ e1000_complete_shutdown(pdev, true, wake);
+
+ return retval;
+}
+
+static int e1000_resume(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (adapter->ecdev) {
+ return -EBUSY;
+ }
+
+ if (e1000e_pm_ready(adapter))
+ adapter->idle_check = true;
+
+ return __e1000_resume(pdev);
+}
+#endif /* CONFIG_PM_SLEEP */
+
+#ifdef CONFIG_PM_RUNTIME
+static int e1000_runtime_suspend(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (e1000e_pm_ready(adapter)) {
+ bool wake;
+
+ __e1000_shutdown(pdev, &wake, true);
+ }
+
+ return 0;
+}
+
+static int e1000_idle(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (!e1000e_pm_ready(adapter))
+ return 0;
+
+ if (adapter->idle_check) {
+ adapter->idle_check = false;
+ if (!e1000e_has_link(adapter))
+ pm_schedule_suspend(dev, MSEC_PER_SEC);
+ }
+
+ return -EBUSY;
+}
+
+static int e1000_runtime_resume(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (!e1000e_pm_ready(adapter))
+ return 0;
+
+ adapter->idle_check = !dev->power.runtime_auto;
+ return __e1000_resume(pdev);
+}
+#endif /* CONFIG_PM_RUNTIME */
+#endif /* CONFIG_PM_OPS */
+
+static void e1000_shutdown(struct pci_dev *pdev)
+{
+ bool wake = false;
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (adapter->ecdev)
+ return;
+
+ __e1000_shutdown(pdev, &wake, false);
+
+ if (system_state == SYSTEM_POWER_OFF)
+ e1000_complete_shutdown(pdev, false, wake);
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+/*
+ * Polling 'interrupt' - used by things like netconsole to send skbs
+ * without having to re-enable interrupts. It's not called while
+ * the interrupt routine is executing.
+ */
+static void e1000_netpoll(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ disable_irq(adapter->pdev->irq);
+ e1000_intr(adapter->pdev->irq, netdev);
+
+ enable_irq(adapter->pdev->irq);
+}
+#endif
+
+/**
+ * e1000_io_error_detected - called when PCI error is detected
+ * @pdev: Pointer to PCI device
+ * @state: The current pci connection state
+ *
+ * This function is called after a PCI bus error affecting
+ * this device has been detected.
+ */
+static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
+ pci_channel_state_t state)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ netif_device_detach(netdev);
+
+ if (state == pci_channel_io_perm_failure)
+ return PCI_ERS_RESULT_DISCONNECT;
+
+ if (netif_running(netdev))
+ e1000e_down(adapter);
+ pci_disable_device(pdev);
+
+ /* Request a slot slot reset. */
+ return PCI_ERS_RESULT_NEED_RESET;
+}
+
+/**
+ * e1000_io_slot_reset - called after the pci bus has been reset.
+ * @pdev: Pointer to PCI device
+ *
+ * Restart the card from scratch, as if from a cold-boot. Implementation
+ * resembles the first-half of the e1000_resume routine.
+ */
+static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ int err;
+ pci_ers_result_t result;
+
+ if (adapter->flags2 & FLAG2_DISABLE_ASPM_L1)
+ e1000e_disable_aspm(pdev, PCIE_LINK_STATE_L1);
+ err = pci_enable_device_mem(pdev);
+ if (err) {
+ dev_err(&pdev->dev,
+ "Cannot re-enable PCI device after reset.\n");
+ result = PCI_ERS_RESULT_DISCONNECT;
+ } else {
+ pci_set_master(pdev);
+ pdev->state_saved = true;
+ pci_restore_state(pdev);
+
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ pci_enable_wake(pdev, PCI_D3cold, 0);
+
+ e1000e_reset(adapter);
+ ew32(WUS, ~0);
+ result = PCI_ERS_RESULT_RECOVERED;
+ }
+
+ pci_cleanup_aer_uncorrect_error_status(pdev);
+
+ return result;
+}
+
+/**
+ * e1000_io_resume - called when traffic can start flowing again.
+ * @pdev: Pointer to PCI device
+ *
+ * This callback is called when the error recovery driver tells us that
+ * its OK to resume normal operation. Implementation resembles the
+ * second-half of the e1000_resume routine.
+ */
+static void e1000_io_resume(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ e1000_init_manageability_pt(adapter);
+
+ if (netif_running(netdev)) {
+ if (e1000e_up(adapter)) {
+ dev_err(&pdev->dev,
+ "can't bring device back up after reset\n");
+ return;
+ }
+ }
+
+ netif_device_attach(netdev);
+
+ /*
+ * If the controller has AMT, do not set DRV_LOAD until the interface
+ * is up. For all other cases, let the f/w know that the h/w is now
+ * under the control of the driver.
+ */
+ if (!(adapter->flags & FLAG_HAS_AMT))
+ e1000_get_hw_control(adapter);
+
+}
+
+static void e1000_print_device_info(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u32 pba_num;
+
+ /* print bus type/speed/width info */
+ e_info("(PCI Express:2.5GB/s:%s) %pM\n",
+ /* bus width */
+ ((hw->bus.width == e1000_bus_width_pcie_x4) ? "Width x4" :
+ "Width x1"),
+ /* MAC address */
+ netdev->dev_addr);
+ e_info("Intel(R) PRO/%s Network Connection\n",
+ (hw->phy.type == e1000_phy_ife) ? "10/100" : "1000");
+ e1000e_read_pba_num(hw, &pba_num);
+ e_info("MAC: %d, PHY: %d, PBA No: %06x-%03x\n",
+ hw->mac.type, hw->phy.type, (pba_num >> 8), (pba_num & 0xff));
+}
+
+static void e1000_eeprom_checks(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ int ret_val;
+ u16 buf = 0;
+
+ if (hw->mac.type != e1000_82573)
+ return;
+
+ ret_val = e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &buf);
+ if (!ret_val && (!(le16_to_cpu(buf) & (1 << 0)))) {
+ /* Deep Smart Power Down (DSPD) */
+ dev_warn(&adapter->pdev->dev,
+ "Warning: detected DSPD enabled in EEPROM\n");
+ }
+}
+
+static const struct net_device_ops e1000e_netdev_ops = {
+ .ndo_open = e1000_open,
+ .ndo_stop = e1000_close,
+ .ndo_start_xmit = e1000_xmit_frame,
+ .ndo_get_stats = e1000_get_stats,
+ .ndo_set_multicast_list = e1000_set_multi,
+ .ndo_set_mac_address = e1000_set_mac,
+ .ndo_change_mtu = e1000_change_mtu,
+ .ndo_do_ioctl = e1000_ioctl,
+ .ndo_tx_timeout = e1000_tx_timeout,
+ .ndo_validate_addr = eth_validate_addr,
+
+ .ndo_vlan_rx_register = e1000_vlan_rx_register,
+ .ndo_vlan_rx_add_vid = e1000_vlan_rx_add_vid,
+ .ndo_vlan_rx_kill_vid = e1000_vlan_rx_kill_vid,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = e1000_netpoll,
+#endif
+};
+
+/**
+ * ec_poll - Ethercat poll Routine
+ * @netdev: net device structure
+ *
+ * This function can never fail.
+ *
+ **/
+void ec_poll(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (jiffies - adapter->ec_watchdog_jiffies >= 2 * HZ) {
+ e1000_watchdog((unsigned long) adapter);
+ adapter->ec_watchdog_jiffies = jiffies;
+ }
+
+#ifdef CONFIG_PCI_MSI
+ e1000_intr_msi(0,netdev);
+#else
+ e1000_intr(0,netdev);
+#endif
+}
+
+/**
+ * e1000_probe - Device Initialization Routine
+ * @pdev: PCI device information struct
+ * @ent: entry in e1000_pci_tbl
+ *
+ * Returns 0 on success, negative on failure
+ *
+ * e1000_probe initializes an adapter identified by a pci_dev structure.
+ * The OS initialization, configuring of the adapter private structure,
+ * and a hardware reset occur.
+ **/
+static int __devinit e1000_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct net_device *netdev;
+ struct e1000_adapter *adapter;
+ struct e1000_hw *hw;
+ const struct e1000_info *ei = e1000_info_tbl[ent->driver_data];
+ resource_size_t mmio_start, mmio_len;
+ resource_size_t flash_start, flash_len;
+
+ static int cards_found;
+ int i, err, pci_using_dac;
+ u16 eeprom_data = 0;
+ u16 eeprom_apme_mask = E1000_EEPROM_APME;
+
+ if (ei->flags2 & FLAG2_DISABLE_ASPM_L1)
+ e1000e_disable_aspm(pdev, PCIE_LINK_STATE_L1);
+
+ err = pci_enable_device_mem(pdev);
+ if (err)
+ return err;
+
+ pci_using_dac = 0;
+ err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
+ if (!err) {
+ err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
+ if (!err)
+ pci_using_dac = 1;
+ } else {
+ err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
+ if (err) {
+ err = dma_set_coherent_mask(&pdev->dev,
+ DMA_BIT_MASK(32));
+ if (err) {
+ dev_err(&pdev->dev, "No usable DMA "
+ "configuration, aborting\n");
+ goto err_dma;
+ }
+ }
+ }
+
+ err = pci_request_selected_regions_exclusive(pdev,
+ pci_select_bars(pdev, IORESOURCE_MEM),
+ e1000e_driver_name);
+ if (err)
+ goto err_pci_reg;
+
+ /* AER (Advanced Error Reporting) hooks */
+ pci_enable_pcie_error_reporting(pdev);
+
+ pci_set_master(pdev);
+ /* PCI config space info */
+ err = pci_save_state(pdev);
+ if (err)
+ goto err_alloc_etherdev;
+
+ err = -ENOMEM;
+ netdev = alloc_etherdev(sizeof(struct e1000_adapter));
+ if (!netdev)
+ goto err_alloc_etherdev;
+
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+
+ netdev->irq = pdev->irq;
+
+ pci_set_drvdata(pdev, netdev);
+ adapter = netdev_priv(netdev);
+ hw = &adapter->hw;
+ adapter->netdev = netdev;
+ adapter->pdev = pdev;
+ adapter->ei = ei;
+ adapter->pba = ei->pba;
+ adapter->flags = ei->flags;
+ adapter->flags2 = ei->flags2;
+ adapter->hw.adapter = adapter;
+ adapter->hw.mac.type = ei->mac;
+ adapter->max_hw_frame_size = ei->max_hw_frame_size;
+ adapter->msg_enable = (1 << NETIF_MSG_DRV | NETIF_MSG_PROBE) - 1;
+
+ mmio_start = pci_resource_start(pdev, 0);
+ mmio_len = pci_resource_len(pdev, 0);
+
+ err = -EIO;
+ adapter->hw.hw_addr = ioremap(mmio_start, mmio_len);
+ if (!adapter->hw.hw_addr)
+ goto err_ioremap;
+
+ if ((adapter->flags & FLAG_HAS_FLASH) &&
+ (pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) {
+ flash_start = pci_resource_start(pdev, 1);
+ flash_len = pci_resource_len(pdev, 1);
+ adapter->hw.flash_address = ioremap(flash_start, flash_len);
+ if (!adapter->hw.flash_address)
+ goto err_flashmap;
+ }
+
+ /* construct the net_device struct */
+ netdev->netdev_ops = &e1000e_netdev_ops;
+ e1000e_set_ethtool_ops(netdev);
+ netdev->watchdog_timeo = 5 * HZ;
+ netif_napi_add(netdev, &adapter->napi, e1000_clean, 64);
+ strncpy(netdev->name, pci_name(pdev), sizeof(netdev->name) - 1);
+
+ netdev->mem_start = mmio_start;
+ netdev->mem_end = mmio_start + mmio_len;
+
+ adapter->bd_number = cards_found++;
+
+ e1000e_check_options(adapter);
+
+ /* setup adapter struct */
+ err = e1000_sw_init(adapter);
+ if (err)
+ goto err_sw_init;
+
+ err = -EIO;
+
+ memcpy(&hw->mac.ops, ei->mac_ops, sizeof(hw->mac.ops));
+ memcpy(&hw->nvm.ops, ei->nvm_ops, sizeof(hw->nvm.ops));
+ memcpy(&hw->phy.ops, ei->phy_ops, sizeof(hw->phy.ops));
+
+ err = ei->get_variants(adapter);
+ if (err)
+ goto err_hw_init;
+
+ if ((adapter->flags & FLAG_IS_ICH) &&
+ (adapter->flags & FLAG_READ_ONLY_NVM))
+ e1000e_write_protect_nvm_ich8lan(&adapter->hw);
+
+ hw->mac.ops.get_bus_info(&adapter->hw);
+
+ adapter->hw.phy.autoneg_wait_to_complete = 0;
+
+ /* Copper options */
+ if (adapter->hw.phy.media_type == e1000_media_type_copper) {
+ adapter->hw.phy.mdix = AUTO_ALL_MODES;
+ adapter->hw.phy.disable_polarity_correction = 0;
+ adapter->hw.phy.ms_type = e1000_ms_hw_default;
+ }
+
+ if (e1000_check_reset_block(&adapter->hw))
+ e_info("PHY reset is blocked due to SOL/IDER session.\n");
+
+ netdev->features = NETIF_F_SG |
+ NETIF_F_HW_CSUM |
+ NETIF_F_HW_VLAN_TX |
+ NETIF_F_HW_VLAN_RX;
+
+ if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER)
+ netdev->features |= NETIF_F_HW_VLAN_FILTER;
+
+ netdev->features |= NETIF_F_TSO;
+ netdev->features |= NETIF_F_TSO6;
+
+ netdev->vlan_features |= NETIF_F_TSO;
+ netdev->vlan_features |= NETIF_F_TSO6;
+ netdev->vlan_features |= NETIF_F_HW_CSUM;
+ netdev->vlan_features |= NETIF_F_SG;
+
+ if (pci_using_dac)
+ netdev->features |= NETIF_F_HIGHDMA;
+
+ if (e1000e_enable_mng_pass_thru(&adapter->hw))
+ adapter->flags |= FLAG_MNG_PT_ENABLED;
+
+ /*
+ * before reading the NVM, reset the controller to
+ * put the device in a known good starting state
+ */
+ adapter->hw.mac.ops.reset_hw(&adapter->hw);
+
+ /*
+ * systems with ASPM and others may see the checksum fail on the first
+ * attempt. Let's give it a few tries
+ */
+ for (i = 0;; i++) {
+ if (e1000_validate_nvm_checksum(&adapter->hw) >= 0)
+ break;
+ if (i == 2) {
+ e_err("The NVM Checksum Is Not Valid\n");
+ err = -EIO;
+ goto err_eeprom;
+ }
+ }
+
+ e1000_eeprom_checks(adapter);
+
+ /* copy the MAC address */
+ if (e1000e_read_mac_addr(&adapter->hw))
+ e_err("NVM Read Error while reading MAC address\n");
+
+ memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
+ memcpy(netdev->perm_addr, adapter->hw.mac.addr, netdev->addr_len);
+
+ if (!is_valid_ether_addr(netdev->perm_addr)) {
+ e_err("Invalid MAC Address: %pM\n", netdev->perm_addr);
+ err = -EIO;
+ goto err_eeprom;
+ }
+
+ init_timer(&adapter->watchdog_timer);
+ adapter->watchdog_timer.function = &e1000_watchdog;
+ adapter->watchdog_timer.data = (unsigned long) adapter;
+
+ init_timer(&adapter->phy_info_timer);
+ adapter->phy_info_timer.function = &e1000_update_phy_info;
+ adapter->phy_info_timer.data = (unsigned long) adapter;
+
+ INIT_WORK(&adapter->reset_task, e1000_reset_task);
+ INIT_WORK(&adapter->watchdog_task, e1000_watchdog_task);
+ INIT_WORK(&adapter->downshift_task, e1000e_downshift_workaround);
+ INIT_WORK(&adapter->update_phy_task, e1000e_update_phy_task);
+ INIT_WORK(&adapter->print_hang_task, e1000_print_hw_hang);
+
+ /* Initialize link parameters. User can change them with ethtool */
+ adapter->hw.mac.autoneg = 1;
+ adapter->fc_autoneg = 1;
+ adapter->hw.fc.requested_mode = e1000_fc_default;
+ adapter->hw.fc.current_mode = e1000_fc_default;
+ adapter->hw.phy.autoneg_advertised = 0x2f;
+
+ /* ring size defaults */
+ adapter->rx_ring->count = 256;
+ adapter->tx_ring->count = 256;
+
+ /*
+ * Initial Wake on LAN setting - If APM wake is enabled in
+ * the EEPROM, enable the ACPI Magic Packet filter
+ */
+ if (adapter->flags & FLAG_APME_IN_WUC) {
+ /* APME bit in EEPROM is mapped to WUC.APME */
+ eeprom_data = er32(WUC);
+ eeprom_apme_mask = E1000_WUC_APME;
+ if (eeprom_data & E1000_WUC_PHY_WAKE)
+ adapter->flags2 |= FLAG2_HAS_PHY_WAKEUP;
+ } else if (adapter->flags & FLAG_APME_IN_CTRL3) {
+ if (adapter->flags & FLAG_APME_CHECK_PORT_B &&
+ (adapter->hw.bus.func == 1))
+ e1000_read_nvm(&adapter->hw,
+ NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
+ else
+ e1000_read_nvm(&adapter->hw,
+ NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
+ }
+
+ /* fetch WoL from EEPROM */
+ if (eeprom_data & eeprom_apme_mask)
+ adapter->eeprom_wol |= E1000_WUFC_MAG;
+
+ /*
+ * now that we have the eeprom settings, apply the special cases
+ * where the eeprom may be wrong or the board simply won't support
+ * wake on lan on a particular port
+ */
+ if (!(adapter->flags & FLAG_HAS_WOL))
+ adapter->eeprom_wol = 0;
+
+ /* initialize the wol settings based on the eeprom settings */
+ adapter->wol = adapter->eeprom_wol;
+ device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
+
+ /* save off EEPROM version number */
+ e1000_read_nvm(&adapter->hw, 5, 1, &adapter->eeprom_vers);
+
+ /* reset the hardware with the new settings */
+ e1000e_reset(adapter);
+
+ /*
+ * If the controller has AMT, do not set DRV_LOAD until the interface
+ * is up. For all other cases, let the f/w know that the h/w is now
+ * under the control of the driver.
+ */
+ if (!(adapter->flags & FLAG_HAS_AMT))
+ e1000_get_hw_control(adapter);
+
+ adapter->ecdev = ecdev_offer(netdev,ec_poll,THIS_MODULE);
+ if (adapter->ecdev) {
+ if (ecdev_open(adapter->ecdev)) {
+ ecdev_withdraw(adapter->ecdev);
+ goto err_register;
+ }
+ } else {
+ strcpy(netdev->name, "eth%d");
+ err = register_netdev(netdev);
+ if (err)
+ goto err_register;
+
+ /* carrier off reporting is important to ethtool even BEFORE open */
+ netif_carrier_off(netdev);
+ }
+
+ e1000_print_device_info(adapter);
+
+ if (pci_dev_run_wake(pdev)) {
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+ }
+ pm_schedule_suspend(&pdev->dev, MSEC_PER_SEC);
+
+ return 0;
+
+err_register:
+ if (!(adapter->flags & FLAG_HAS_AMT))
+ e1000_release_hw_control(adapter);
+err_eeprom:
+ if (!e1000_check_reset_block(&adapter->hw))
+ e1000_phy_hw_reset(&adapter->hw);
+err_hw_init:
+
+ kfree(adapter->tx_ring);
+ kfree(adapter->rx_ring);
+err_sw_init:
+ if (adapter->hw.flash_address)
+ iounmap(adapter->hw.flash_address);
+ e1000e_reset_interrupt_capability(adapter);
+err_flashmap:
+ iounmap(adapter->hw.hw_addr);
+err_ioremap:
+ free_netdev(netdev);
+err_alloc_etherdev:
+ pci_release_selected_regions(pdev,
+ pci_select_bars(pdev, IORESOURCE_MEM));
+err_pci_reg:
+err_dma:
+ pci_disable_device(pdev);
+ return err;
+}
+
+/**
+ * e1000_remove - Device Removal Routine
+ * @pdev: PCI device information struct
+ *
+ * e1000_remove is called by the PCI subsystem to alert the driver
+ * that it should release a PCI device. The could be caused by a
+ * Hot-Plug event, or because the driver is going to be removed from
+ * memory.
+ **/
+static void __devexit e1000_remove(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ bool down = test_bit(__E1000_DOWN, &adapter->state);
+
+ pm_runtime_get_sync(&pdev->dev);
+
+ /*
+ * flush_scheduled work may reschedule our watchdog task, so
+ * explicitly disable watchdog tasks from being rescheduled
+ */
+ if (!down)
+ set_bit(__E1000_DOWN, &adapter->state);
+ del_timer_sync(&adapter->watchdog_timer);
+ del_timer_sync(&adapter->phy_info_timer);
+
+ cancel_work_sync(&adapter->reset_task);
+ cancel_work_sync(&adapter->watchdog_task);
+ cancel_work_sync(&adapter->downshift_task);
+ cancel_work_sync(&adapter->update_phy_task);
+ cancel_work_sync(&adapter->print_hang_task);
+ flush_scheduled_work();
+
+ if (!(netdev->flags & IFF_UP))
+ e1000_power_down_phy(adapter);
+
+ /* Don't lie to e1000_close() down the road. */
+ if (!down)
+ clear_bit(__E1000_DOWN, &adapter->state);
+
+ if (adapter->ecdev) {
+ ecdev_close(adapter->ecdev);
+ ecdev_withdraw(adapter->ecdev);
+ } else {
+ unregister_netdev(netdev);
+ }
+
+ if (pci_dev_run_wake(pdev)) {
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_set_suspended(&pdev->dev);
+ }
+ pm_runtime_put_noidle(&pdev->dev);
+
+ /*
+ * Release control of h/w to f/w. If f/w is AMT enabled, this
+ * would have already happened in close and is redundant.
+ */
+ e1000_release_hw_control(adapter);
+
+ e1000e_reset_interrupt_capability(adapter);
+ kfree(adapter->tx_ring);
+ kfree(adapter->rx_ring);
+
+ iounmap(adapter->hw.hw_addr);
+ if (adapter->hw.flash_address)
+ iounmap(adapter->hw.flash_address);
+ pci_release_selected_regions(pdev,
+ pci_select_bars(pdev, IORESOURCE_MEM));
+
+ free_netdev(netdev);
+
+ /* AER disable */
+ pci_disable_pcie_error_reporting(pdev);
+
+ pci_disable_device(pdev);
+}
+
+/* PCI Error Recovery (ERS) */
+static struct pci_error_handlers e1000_err_handler = {
+ .error_detected = e1000_io_error_detected,
+ .slot_reset = e1000_io_slot_reset,
+ .resume = e1000_io_resume,
+};
+
+static DEFINE_PCI_DEVICE_TABLE(e1000_pci_tbl) = {
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_COPPER), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_FIBER), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER_LP), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_FIBER), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_DUAL), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_QUAD), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571PT_QUAD_COPPER), board_82571 },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI), board_82572 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_COPPER), board_82572 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_FIBER), board_82572 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_SERDES), board_82572 },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E), board_82573 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E_IAMT), board_82573 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573L), board_82573 },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82574L), board_82574 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82574LA), board_82574 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82583V), board_82583 },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_DPT),
+ board_80003es2lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_SPT),
+ board_80003es2lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_DPT),
+ board_80003es2lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_SPT),
+ board_80003es2lan },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_G), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_GT), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_AMT), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_C), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M_AMT), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_82567V_3), board_ich8lan },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_G), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_GT), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_AMT), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_C), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_BM), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_AMT), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_V), board_ich9lan },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LM), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LF), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_V), board_ich9lan },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LM), board_ich10lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LF), board_ich10lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_V), board_ich10lan },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LM), board_pchlan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LC), board_pchlan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DM), board_pchlan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DC), board_pchlan },
+
+ { } /* terminate list */
+};
+//MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
+
+#ifdef CONFIG_PM_OPS
+static const struct dev_pm_ops e1000_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(e1000_suspend, e1000_resume)
+ SET_RUNTIME_PM_OPS(e1000_runtime_suspend,
+ e1000_runtime_resume, e1000_idle)
+};
+#endif
+
+/* PCI Device API Driver */
+static struct pci_driver e1000_driver = {
+ .name = e1000e_driver_name,
+ .id_table = e1000_pci_tbl,
+ .probe = e1000_probe,
+ .remove = __devexit_p(e1000_remove),
+#ifdef CONFIG_PM_OPS
+ .driver.pm = &e1000_pm_ops,
+#endif
+ .shutdown = e1000_shutdown,
+ .err_handler = &e1000_err_handler
+};
+
+/**
+ * e1000_init_module - Driver Registration Routine
+ *
+ * e1000_init_module is the first routine called when the driver is
+ * loaded. All it does is register with the PCI subsystem.
+ **/
+static int __init e1000_init_module(void)
+{
+ int ret;
+ pr_info("EtherCAT-capable Intel(R) PRO/1000 Network Driver - %s\n",
+ e1000e_driver_version);
+ pr_info("Copyright (c) 1999 - 2009 Intel Corporation.\n");
+ ret = pci_register_driver(&e1000_driver);
+
+ return ret;
+}
+module_init(e1000_init_module);
+
+/**
+ * e1000_exit_module - Driver Exit Cleanup Routine
+ *
+ * e1000_exit_module is called just before the driver is removed
+ * from memory.
+ **/
+static void __exit e1000_exit_module(void)
+{
+ pci_unregister_driver(&e1000_driver);
+}
+module_exit(e1000_exit_module);
+
+
+MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
+MODULE_DESCRIPTION("Ethercat-capable Intel(R) PRO/1000 Network Driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+/* e1000_main.c */