--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e100-2.6.35-orig.c Tue Apr 10 19:10:56 2012 +0200
@@ -0,0 +1,3115 @@
+/*******************************************************************************
+
+ Intel PRO/100 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/*
+ * e100.c: Intel(R) PRO/100 ethernet driver
+ *
+ * (Re)written 2003 by scott.feldman@intel.com. Based loosely on
+ * original e100 driver, but better described as a munging of
+ * e100, e1000, eepro100, tg3, 8139cp, and other drivers.
+ *
+ * References:
+ * Intel 8255x 10/100 Mbps Ethernet Controller Family,
+ * Open Source Software Developers Manual,
+ * http://sourceforge.net/projects/e1000
+ *
+ *
+ * Theory of Operation
+ *
+ * I. General
+ *
+ * The driver supports Intel(R) 10/100 Mbps PCI Fast Ethernet
+ * controller family, which includes the 82557, 82558, 82559, 82550,
+ * 82551, and 82562 devices. 82558 and greater controllers
+ * integrate the Intel 82555 PHY. The controllers are used in
+ * server and client network interface cards, as well as in
+ * LAN-On-Motherboard (LOM), CardBus, MiniPCI, and ICHx
+ * configurations. 8255x supports a 32-bit linear addressing
+ * mode and operates at 33Mhz PCI clock rate.
+ *
+ * II. Driver Operation
+ *
+ * Memory-mapped mode is used exclusively to access the device's
+ * shared-memory structure, the Control/Status Registers (CSR). All
+ * setup, configuration, and control of the device, including queuing
+ * of Tx, Rx, and configuration commands is through the CSR.
+ * cmd_lock serializes accesses to the CSR command register. cb_lock
+ * protects the shared Command Block List (CBL).
+ *
+ * 8255x is highly MII-compliant and all access to the PHY go
+ * through the Management Data Interface (MDI). Consequently, the
+ * driver leverages the mii.c library shared with other MII-compliant
+ * devices.
+ *
+ * Big- and Little-Endian byte order as well as 32- and 64-bit
+ * archs are supported. Weak-ordered memory and non-cache-coherent
+ * archs are supported.
+ *
+ * III. Transmit
+ *
+ * A Tx skb is mapped and hangs off of a TCB. TCBs are linked
+ * together in a fixed-size ring (CBL) thus forming the flexible mode
+ * memory structure. A TCB marked with the suspend-bit indicates
+ * the end of the ring. The last TCB processed suspends the
+ * controller, and the controller can be restarted by issue a CU
+ * resume command to continue from the suspend point, or a CU start
+ * command to start at a given position in the ring.
+ *
+ * Non-Tx commands (config, multicast setup, etc) are linked
+ * into the CBL ring along with Tx commands. The common structure
+ * used for both Tx and non-Tx commands is the Command Block (CB).
+ *
+ * cb_to_use is the next CB to use for queuing a command; cb_to_clean
+ * is the next CB to check for completion; cb_to_send is the first
+ * CB to start on in case of a previous failure to resume. CB clean
+ * up happens in interrupt context in response to a CU interrupt.
+ * cbs_avail keeps track of number of free CB resources available.
+ *
+ * Hardware padding of short packets to minimum packet size is
+ * enabled. 82557 pads with 7Eh, while the later controllers pad
+ * with 00h.
+ *
+ * IV. Receive
+ *
+ * The Receive Frame Area (RFA) comprises a ring of Receive Frame
+ * Descriptors (RFD) + data buffer, thus forming the simplified mode
+ * memory structure. Rx skbs are allocated to contain both the RFD
+ * and the data buffer, but the RFD is pulled off before the skb is
+ * indicated. The data buffer is aligned such that encapsulated
+ * protocol headers are u32-aligned. Since the RFD is part of the
+ * mapped shared memory, and completion status is contained within
+ * the RFD, the RFD must be dma_sync'ed to maintain a consistent
+ * view from software and hardware.
+ *
+ * In order to keep updates to the RFD link field from colliding with
+ * hardware writes to mark packets complete, we use the feature that
+ * hardware will not write to a size 0 descriptor and mark the previous
+ * packet as end-of-list (EL). After updating the link, we remove EL
+ * and only then restore the size such that hardware may use the
+ * previous-to-end RFD.
+ *
+ * Under typical operation, the receive unit (RU) is start once,
+ * and the controller happily fills RFDs as frames arrive. If
+ * replacement RFDs cannot be allocated, or the RU goes non-active,
+ * the RU must be restarted. Frame arrival generates an interrupt,
+ * and Rx indication and re-allocation happen in the same context,
+ * therefore no locking is required. A software-generated interrupt
+ * is generated from the watchdog to recover from a failed allocation
+ * scenario where all Rx resources have been indicated and none re-
+ * placed.
+ *
+ * V. Miscellaneous
+ *
+ * VLAN offloading of tagging, stripping and filtering is not
+ * supported, but driver will accommodate the extra 4-byte VLAN tag
+ * for processing by upper layers. Tx/Rx Checksum offloading is not
+ * supported. Tx Scatter/Gather is not supported. Jumbo Frames is
+ * not supported (hardware limitation).
+ *
+ * MagicPacket(tm) WoL support is enabled/disabled via ethtool.
+ *
+ * Thanks to JC (jchapman@katalix.com) for helping with
+ * testing/troubleshooting the development driver.
+ *
+ * TODO:
+ * o several entry points race with dev->close
+ * o check for tx-no-resources/stop Q races with tx clean/wake Q
+ *
+ * FIXES:
+ * 2005/12/02 - Michael O'Donnell <Michael.ODonnell at stratus dot com>
+ * - Stratus87247: protect MDI control register manipulations
+ * 2009/06/01 - Andreas Mohr <andi at lisas dot de>
+ * - add clean lowlevel I/O emulation for cards with MII-lacking PHYs
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/mii.h>
+#include <linux/if_vlan.h>
+#include <linux/skbuff.h>
+#include <linux/ethtool.h>
+#include <linux/string.h>
+#include <linux/firmware.h>
+#include <linux/rtnetlink.h>
+#include <asm/unaligned.h>
+
+
+#define DRV_NAME "e100"
+#define DRV_EXT "-NAPI"
+#define DRV_VERSION "3.5.24-k2"DRV_EXT
+#define DRV_DESCRIPTION "Intel(R) PRO/100 Network Driver"
+#define DRV_COPYRIGHT "Copyright(c) 1999-2006 Intel Corporation"
+
+#define E100_WATCHDOG_PERIOD (2 * HZ)
+#define E100_NAPI_WEIGHT 16
+
+#define FIRMWARE_D101M "e100/d101m_ucode.bin"
+#define FIRMWARE_D101S "e100/d101s_ucode.bin"
+#define FIRMWARE_D102E "e100/d102e_ucode.bin"
+
+MODULE_DESCRIPTION(DRV_DESCRIPTION);
+MODULE_AUTHOR(DRV_COPYRIGHT);
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+MODULE_FIRMWARE(FIRMWARE_D101M);
+MODULE_FIRMWARE(FIRMWARE_D101S);
+MODULE_FIRMWARE(FIRMWARE_D102E);
+
+static int debug = 3;
+static int eeprom_bad_csum_allow = 0;
+static int use_io = 0;
+module_param(debug, int, 0);
+module_param(eeprom_bad_csum_allow, int, 0);
+module_param(use_io, int, 0);
+MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
+MODULE_PARM_DESC(eeprom_bad_csum_allow, "Allow bad eeprom checksums");
+MODULE_PARM_DESC(use_io, "Force use of i/o access mode");
+
+#define INTEL_8255X_ETHERNET_DEVICE(device_id, ich) {\
+ PCI_VENDOR_ID_INTEL, device_id, PCI_ANY_ID, PCI_ANY_ID, \
+ PCI_CLASS_NETWORK_ETHERNET << 8, 0xFFFF00, ich }
+static DEFINE_PCI_DEVICE_TABLE(e100_id_table) = {
+ INTEL_8255X_ETHERNET_DEVICE(0x1029, 0),
+ INTEL_8255X_ETHERNET_DEVICE(0x1030, 0),
+ INTEL_8255X_ETHERNET_DEVICE(0x1031, 3),
+ INTEL_8255X_ETHERNET_DEVICE(0x1032, 3),
+ INTEL_8255X_ETHERNET_DEVICE(0x1033, 3),
+ INTEL_8255X_ETHERNET_DEVICE(0x1034, 3),
+ INTEL_8255X_ETHERNET_DEVICE(0x1038, 3),
+ INTEL_8255X_ETHERNET_DEVICE(0x1039, 4),
+ INTEL_8255X_ETHERNET_DEVICE(0x103A, 4),
+ INTEL_8255X_ETHERNET_DEVICE(0x103B, 4),
+ INTEL_8255X_ETHERNET_DEVICE(0x103C, 4),
+ INTEL_8255X_ETHERNET_DEVICE(0x103D, 4),
+ INTEL_8255X_ETHERNET_DEVICE(0x103E, 4),
+ INTEL_8255X_ETHERNET_DEVICE(0x1050, 5),
+ INTEL_8255X_ETHERNET_DEVICE(0x1051, 5),
+ INTEL_8255X_ETHERNET_DEVICE(0x1052, 5),
+ INTEL_8255X_ETHERNET_DEVICE(0x1053, 5),
+ INTEL_8255X_ETHERNET_DEVICE(0x1054, 5),
+ INTEL_8255X_ETHERNET_DEVICE(0x1055, 5),
+ INTEL_8255X_ETHERNET_DEVICE(0x1056, 5),
+ INTEL_8255X_ETHERNET_DEVICE(0x1057, 5),
+ INTEL_8255X_ETHERNET_DEVICE(0x1059, 0),
+ INTEL_8255X_ETHERNET_DEVICE(0x1064, 6),
+ INTEL_8255X_ETHERNET_DEVICE(0x1065, 6),
+ INTEL_8255X_ETHERNET_DEVICE(0x1066, 6),
+ INTEL_8255X_ETHERNET_DEVICE(0x1067, 6),
+ INTEL_8255X_ETHERNET_DEVICE(0x1068, 6),
+ INTEL_8255X_ETHERNET_DEVICE(0x1069, 6),
+ INTEL_8255X_ETHERNET_DEVICE(0x106A, 6),
+ INTEL_8255X_ETHERNET_DEVICE(0x106B, 6),
+ INTEL_8255X_ETHERNET_DEVICE(0x1091, 7),
+ INTEL_8255X_ETHERNET_DEVICE(0x1092, 7),
+ INTEL_8255X_ETHERNET_DEVICE(0x1093, 7),
+ INTEL_8255X_ETHERNET_DEVICE(0x1094, 7),
+ INTEL_8255X_ETHERNET_DEVICE(0x1095, 7),
+ INTEL_8255X_ETHERNET_DEVICE(0x10fe, 7),
+ INTEL_8255X_ETHERNET_DEVICE(0x1209, 0),
+ INTEL_8255X_ETHERNET_DEVICE(0x1229, 0),
+ INTEL_8255X_ETHERNET_DEVICE(0x2449, 2),
+ INTEL_8255X_ETHERNET_DEVICE(0x2459, 2),
+ INTEL_8255X_ETHERNET_DEVICE(0x245D, 2),
+ INTEL_8255X_ETHERNET_DEVICE(0x27DC, 7),
+ { 0, }
+};
+MODULE_DEVICE_TABLE(pci, e100_id_table);
+
+enum mac {
+ mac_82557_D100_A = 0,
+ mac_82557_D100_B = 1,
+ mac_82557_D100_C = 2,
+ mac_82558_D101_A4 = 4,
+ mac_82558_D101_B0 = 5,
+ mac_82559_D101M = 8,
+ mac_82559_D101S = 9,
+ mac_82550_D102 = 12,
+ mac_82550_D102_C = 13,
+ mac_82551_E = 14,
+ mac_82551_F = 15,
+ mac_82551_10 = 16,
+ mac_unknown = 0xFF,
+};
+
+enum phy {
+ phy_100a = 0x000003E0,
+ phy_100c = 0x035002A8,
+ phy_82555_tx = 0x015002A8,
+ phy_nsc_tx = 0x5C002000,
+ phy_82562_et = 0x033002A8,
+ phy_82562_em = 0x032002A8,
+ phy_82562_ek = 0x031002A8,
+ phy_82562_eh = 0x017002A8,
+ phy_82552_v = 0xd061004d,
+ phy_unknown = 0xFFFFFFFF,
+};
+
+/* CSR (Control/Status Registers) */
+struct csr {
+ struct {
+ u8 status;
+ u8 stat_ack;
+ u8 cmd_lo;
+ u8 cmd_hi;
+ u32 gen_ptr;
+ } scb;
+ u32 port;
+ u16 flash_ctrl;
+ u8 eeprom_ctrl_lo;
+ u8 eeprom_ctrl_hi;
+ u32 mdi_ctrl;
+ u32 rx_dma_count;
+};
+
+enum scb_status {
+ rus_no_res = 0x08,
+ rus_ready = 0x10,
+ rus_mask = 0x3C,
+};
+
+enum ru_state {
+ RU_SUSPENDED = 0,
+ RU_RUNNING = 1,
+ RU_UNINITIALIZED = -1,
+};
+
+enum scb_stat_ack {
+ stat_ack_not_ours = 0x00,
+ stat_ack_sw_gen = 0x04,
+ stat_ack_rnr = 0x10,
+ stat_ack_cu_idle = 0x20,
+ stat_ack_frame_rx = 0x40,
+ stat_ack_cu_cmd_done = 0x80,
+ stat_ack_not_present = 0xFF,
+ stat_ack_rx = (stat_ack_sw_gen | stat_ack_rnr | stat_ack_frame_rx),
+ stat_ack_tx = (stat_ack_cu_idle | stat_ack_cu_cmd_done),
+};
+
+enum scb_cmd_hi {
+ irq_mask_none = 0x00,
+ irq_mask_all = 0x01,
+ irq_sw_gen = 0x02,
+};
+
+enum scb_cmd_lo {
+ cuc_nop = 0x00,
+ ruc_start = 0x01,
+ ruc_load_base = 0x06,
+ cuc_start = 0x10,
+ cuc_resume = 0x20,
+ cuc_dump_addr = 0x40,
+ cuc_dump_stats = 0x50,
+ cuc_load_base = 0x60,
+ cuc_dump_reset = 0x70,
+};
+
+enum cuc_dump {
+ cuc_dump_complete = 0x0000A005,
+ cuc_dump_reset_complete = 0x0000A007,
+};
+
+enum port {
+ software_reset = 0x0000,
+ selftest = 0x0001,
+ selective_reset = 0x0002,
+};
+
+enum eeprom_ctrl_lo {
+ eesk = 0x01,
+ eecs = 0x02,
+ eedi = 0x04,
+ eedo = 0x08,
+};
+
+enum mdi_ctrl {
+ mdi_write = 0x04000000,
+ mdi_read = 0x08000000,
+ mdi_ready = 0x10000000,
+};
+
+enum eeprom_op {
+ op_write = 0x05,
+ op_read = 0x06,
+ op_ewds = 0x10,
+ op_ewen = 0x13,
+};
+
+enum eeprom_offsets {
+ eeprom_cnfg_mdix = 0x03,
+ eeprom_phy_iface = 0x06,
+ eeprom_id = 0x0A,
+ eeprom_config_asf = 0x0D,
+ eeprom_smbus_addr = 0x90,
+};
+
+enum eeprom_cnfg_mdix {
+ eeprom_mdix_enabled = 0x0080,
+};
+
+enum eeprom_phy_iface {
+ NoSuchPhy = 0,
+ I82553AB,
+ I82553C,
+ I82503,
+ DP83840,
+ S80C240,
+ S80C24,
+ I82555,
+ DP83840A = 10,
+};
+
+enum eeprom_id {
+ eeprom_id_wol = 0x0020,
+};
+
+enum eeprom_config_asf {
+ eeprom_asf = 0x8000,
+ eeprom_gcl = 0x4000,
+};
+
+enum cb_status {
+ cb_complete = 0x8000,
+ cb_ok = 0x2000,
+};
+
+enum cb_command {
+ cb_nop = 0x0000,
+ cb_iaaddr = 0x0001,
+ cb_config = 0x0002,
+ cb_multi = 0x0003,
+ cb_tx = 0x0004,
+ cb_ucode = 0x0005,
+ cb_dump = 0x0006,
+ cb_tx_sf = 0x0008,
+ cb_cid = 0x1f00,
+ cb_i = 0x2000,
+ cb_s = 0x4000,
+ cb_el = 0x8000,
+};
+
+struct rfd {
+ __le16 status;
+ __le16 command;
+ __le32 link;
+ __le32 rbd;
+ __le16 actual_size;
+ __le16 size;
+};
+
+struct rx {
+ struct rx *next, *prev;
+ struct sk_buff *skb;
+ dma_addr_t dma_addr;
+};
+
+#if defined(__BIG_ENDIAN_BITFIELD)
+#define X(a,b) b,a
+#else
+#define X(a,b) a,b
+#endif
+struct config {
+/*0*/ u8 X(byte_count:6, pad0:2);
+/*1*/ u8 X(X(rx_fifo_limit:4, tx_fifo_limit:3), pad1:1);
+/*2*/ u8 adaptive_ifs;
+/*3*/ u8 X(X(X(X(mwi_enable:1, type_enable:1), read_align_enable:1),
+ term_write_cache_line:1), pad3:4);
+/*4*/ u8 X(rx_dma_max_count:7, pad4:1);
+/*5*/ u8 X(tx_dma_max_count:7, dma_max_count_enable:1);
+/*6*/ u8 X(X(X(X(X(X(X(late_scb_update:1, direct_rx_dma:1),
+ tno_intr:1), cna_intr:1), standard_tcb:1), standard_stat_counter:1),
+ rx_discard_overruns:1), rx_save_bad_frames:1);
+/*7*/ u8 X(X(X(X(X(rx_discard_short_frames:1, tx_underrun_retry:2),
+ pad7:2), rx_extended_rfd:1), tx_two_frames_in_fifo:1),
+ tx_dynamic_tbd:1);
+/*8*/ u8 X(X(mii_mode:1, pad8:6), csma_disabled:1);
+/*9*/ u8 X(X(X(X(X(rx_tcpudp_checksum:1, pad9:3), vlan_arp_tco:1),
+ link_status_wake:1), arp_wake:1), mcmatch_wake:1);
+/*10*/ u8 X(X(X(pad10:3, no_source_addr_insertion:1), preamble_length:2),
+ loopback:2);
+/*11*/ u8 X(linear_priority:3, pad11:5);
+/*12*/ u8 X(X(linear_priority_mode:1, pad12:3), ifs:4);
+/*13*/ u8 ip_addr_lo;
+/*14*/ u8 ip_addr_hi;
+/*15*/ u8 X(X(X(X(X(X(X(promiscuous_mode:1, broadcast_disabled:1),
+ wait_after_win:1), pad15_1:1), ignore_ul_bit:1), crc_16_bit:1),
+ pad15_2:1), crs_or_cdt:1);
+/*16*/ u8 fc_delay_lo;
+/*17*/ u8 fc_delay_hi;
+/*18*/ u8 X(X(X(X(X(rx_stripping:1, tx_padding:1), rx_crc_transfer:1),
+ rx_long_ok:1), fc_priority_threshold:3), pad18:1);
+/*19*/ u8 X(X(X(X(X(X(X(addr_wake:1, magic_packet_disable:1),
+ fc_disable:1), fc_restop:1), fc_restart:1), fc_reject:1),
+ full_duplex_force:1), full_duplex_pin:1);
+/*20*/ u8 X(X(X(pad20_1:5, fc_priority_location:1), multi_ia:1), pad20_2:1);
+/*21*/ u8 X(X(pad21_1:3, multicast_all:1), pad21_2:4);
+/*22*/ u8 X(X(rx_d102_mode:1, rx_vlan_drop:1), pad22:6);
+ u8 pad_d102[9];
+};
+
+#define E100_MAX_MULTICAST_ADDRS 64
+struct multi {
+ __le16 count;
+ u8 addr[E100_MAX_MULTICAST_ADDRS * ETH_ALEN + 2/*pad*/];
+};
+
+/* Important: keep total struct u32-aligned */
+#define UCODE_SIZE 134
+struct cb {
+ __le16 status;
+ __le16 command;
+ __le32 link;
+ union {
+ u8 iaaddr[ETH_ALEN];
+ __le32 ucode[UCODE_SIZE];
+ struct config config;
+ struct multi multi;
+ struct {
+ u32 tbd_array;
+ u16 tcb_byte_count;
+ u8 threshold;
+ u8 tbd_count;
+ struct {
+ __le32 buf_addr;
+ __le16 size;
+ u16 eol;
+ } tbd;
+ } tcb;
+ __le32 dump_buffer_addr;
+ } u;
+ struct cb *next, *prev;
+ dma_addr_t dma_addr;
+ struct sk_buff *skb;
+};
+
+enum loopback {
+ lb_none = 0, lb_mac = 1, lb_phy = 3,
+};
+
+struct stats {
+ __le32 tx_good_frames, tx_max_collisions, tx_late_collisions,
+ tx_underruns, tx_lost_crs, tx_deferred, tx_single_collisions,
+ tx_multiple_collisions, tx_total_collisions;
+ __le32 rx_good_frames, rx_crc_errors, rx_alignment_errors,
+ rx_resource_errors, rx_overrun_errors, rx_cdt_errors,
+ rx_short_frame_errors;
+ __le32 fc_xmt_pause, fc_rcv_pause, fc_rcv_unsupported;
+ __le16 xmt_tco_frames, rcv_tco_frames;
+ __le32 complete;
+};
+
+struct mem {
+ struct {
+ u32 signature;
+ u32 result;
+ } selftest;
+ struct stats stats;
+ u8 dump_buf[596];
+};
+
+struct param_range {
+ u32 min;
+ u32 max;
+ u32 count;
+};
+
+struct params {
+ struct param_range rfds;
+ struct param_range cbs;
+};
+
+struct nic {
+ /* Begin: frequently used values: keep adjacent for cache effect */
+ u32 msg_enable ____cacheline_aligned;
+ struct net_device *netdev;
+ struct pci_dev *pdev;
+ u16 (*mdio_ctrl)(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data);
+
+ struct rx *rxs ____cacheline_aligned;
+ struct rx *rx_to_use;
+ struct rx *rx_to_clean;
+ struct rfd blank_rfd;
+ enum ru_state ru_running;
+
+ spinlock_t cb_lock ____cacheline_aligned;
+ spinlock_t cmd_lock;
+ struct csr __iomem *csr;
+ enum scb_cmd_lo cuc_cmd;
+ unsigned int cbs_avail;
+ struct napi_struct napi;
+ struct cb *cbs;
+ struct cb *cb_to_use;
+ struct cb *cb_to_send;
+ struct cb *cb_to_clean;
+ __le16 tx_command;
+ /* End: frequently used values: keep adjacent for cache effect */
+
+ enum {
+ ich = (1 << 0),
+ promiscuous = (1 << 1),
+ multicast_all = (1 << 2),
+ wol_magic = (1 << 3),
+ ich_10h_workaround = (1 << 4),
+ } flags ____cacheline_aligned;
+
+ enum mac mac;
+ enum phy phy;
+ struct params params;
+ struct timer_list watchdog;
+ struct timer_list blink_timer;
+ struct mii_if_info mii;
+ struct work_struct tx_timeout_task;
+ enum loopback loopback;
+
+ struct mem *mem;
+ dma_addr_t dma_addr;
+
+ struct pci_pool *cbs_pool;
+ dma_addr_t cbs_dma_addr;
+ u8 adaptive_ifs;
+ u8 tx_threshold;
+ u32 tx_frames;
+ u32 tx_collisions;
+ u32 tx_deferred;
+ u32 tx_single_collisions;
+ u32 tx_multiple_collisions;
+ u32 tx_fc_pause;
+ u32 tx_tco_frames;
+
+ u32 rx_fc_pause;
+ u32 rx_fc_unsupported;
+ u32 rx_tco_frames;
+ u32 rx_over_length_errors;
+
+ u16 leds;
+ u16 eeprom_wc;
+ __le16 eeprom[256];
+ spinlock_t mdio_lock;
+ const struct firmware *fw;
+};
+
+static inline void e100_write_flush(struct nic *nic)
+{
+ /* Flush previous PCI writes through intermediate bridges
+ * by doing a benign read */
+ (void)ioread8(&nic->csr->scb.status);
+}
+
+static void e100_enable_irq(struct nic *nic)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&nic->cmd_lock, flags);
+ iowrite8(irq_mask_none, &nic->csr->scb.cmd_hi);
+ e100_write_flush(nic);
+ spin_unlock_irqrestore(&nic->cmd_lock, flags);
+}
+
+static void e100_disable_irq(struct nic *nic)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&nic->cmd_lock, flags);
+ iowrite8(irq_mask_all, &nic->csr->scb.cmd_hi);
+ e100_write_flush(nic);
+ spin_unlock_irqrestore(&nic->cmd_lock, flags);
+}
+
+static void e100_hw_reset(struct nic *nic)
+{
+ /* Put CU and RU into idle with a selective reset to get
+ * device off of PCI bus */
+ iowrite32(selective_reset, &nic->csr->port);
+ e100_write_flush(nic); udelay(20);
+
+ /* Now fully reset device */
+ iowrite32(software_reset, &nic->csr->port);
+ e100_write_flush(nic); udelay(20);
+
+ /* Mask off our interrupt line - it's unmasked after reset */
+ e100_disable_irq(nic);
+}
+
+static int e100_self_test(struct nic *nic)
+{
+ u32 dma_addr = nic->dma_addr + offsetof(struct mem, selftest);
+
+ /* Passing the self-test is a pretty good indication
+ * that the device can DMA to/from host memory */
+
+ nic->mem->selftest.signature = 0;
+ nic->mem->selftest.result = 0xFFFFFFFF;
+
+ iowrite32(selftest | dma_addr, &nic->csr->port);
+ e100_write_flush(nic);
+ /* Wait 10 msec for self-test to complete */
+ msleep(10);
+
+ /* Interrupts are enabled after self-test */
+ e100_disable_irq(nic);
+
+ /* Check results of self-test */
+ if (nic->mem->selftest.result != 0) {
+ netif_err(nic, hw, nic->netdev,
+ "Self-test failed: result=0x%08X\n",
+ nic->mem->selftest.result);
+ return -ETIMEDOUT;
+ }
+ if (nic->mem->selftest.signature == 0) {
+ netif_err(nic, hw, nic->netdev, "Self-test failed: timed out\n");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static void e100_eeprom_write(struct nic *nic, u16 addr_len, u16 addr, __le16 data)
+{
+ u32 cmd_addr_data[3];
+ u8 ctrl;
+ int i, j;
+
+ /* Three cmds: write/erase enable, write data, write/erase disable */
+ cmd_addr_data[0] = op_ewen << (addr_len - 2);
+ cmd_addr_data[1] = (((op_write << addr_len) | addr) << 16) |
+ le16_to_cpu(data);
+ cmd_addr_data[2] = op_ewds << (addr_len - 2);
+
+ /* Bit-bang cmds to write word to eeprom */
+ for (j = 0; j < 3; j++) {
+
+ /* Chip select */
+ iowrite8(eecs | eesk, &nic->csr->eeprom_ctrl_lo);
+ e100_write_flush(nic); udelay(4);
+
+ for (i = 31; i >= 0; i--) {
+ ctrl = (cmd_addr_data[j] & (1 << i)) ?
+ eecs | eedi : eecs;
+ iowrite8(ctrl, &nic->csr->eeprom_ctrl_lo);
+ e100_write_flush(nic); udelay(4);
+
+ iowrite8(ctrl | eesk, &nic->csr->eeprom_ctrl_lo);
+ e100_write_flush(nic); udelay(4);
+ }
+ /* Wait 10 msec for cmd to complete */
+ msleep(10);
+
+ /* Chip deselect */
+ iowrite8(0, &nic->csr->eeprom_ctrl_lo);
+ e100_write_flush(nic); udelay(4);
+ }
+};
+
+/* General technique stolen from the eepro100 driver - very clever */
+static __le16 e100_eeprom_read(struct nic *nic, u16 *addr_len, u16 addr)
+{
+ u32 cmd_addr_data;
+ u16 data = 0;
+ u8 ctrl;
+ int i;
+
+ cmd_addr_data = ((op_read << *addr_len) | addr) << 16;
+
+ /* Chip select */
+ iowrite8(eecs | eesk, &nic->csr->eeprom_ctrl_lo);
+ e100_write_flush(nic); udelay(4);
+
+ /* Bit-bang to read word from eeprom */
+ for (i = 31; i >= 0; i--) {
+ ctrl = (cmd_addr_data & (1 << i)) ? eecs | eedi : eecs;
+ iowrite8(ctrl, &nic->csr->eeprom_ctrl_lo);
+ e100_write_flush(nic); udelay(4);
+
+ iowrite8(ctrl | eesk, &nic->csr->eeprom_ctrl_lo);
+ e100_write_flush(nic); udelay(4);
+
+ /* Eeprom drives a dummy zero to EEDO after receiving
+ * complete address. Use this to adjust addr_len. */
+ ctrl = ioread8(&nic->csr->eeprom_ctrl_lo);
+ if (!(ctrl & eedo) && i > 16) {
+ *addr_len -= (i - 16);
+ i = 17;
+ }
+
+ data = (data << 1) | (ctrl & eedo ? 1 : 0);
+ }
+
+ /* Chip deselect */
+ iowrite8(0, &nic->csr->eeprom_ctrl_lo);
+ e100_write_flush(nic); udelay(4);
+
+ return cpu_to_le16(data);
+};
+
+/* Load entire EEPROM image into driver cache and validate checksum */
+static int e100_eeprom_load(struct nic *nic)
+{
+ u16 addr, addr_len = 8, checksum = 0;
+
+ /* Try reading with an 8-bit addr len to discover actual addr len */
+ e100_eeprom_read(nic, &addr_len, 0);
+ nic->eeprom_wc = 1 << addr_len;
+
+ for (addr = 0; addr < nic->eeprom_wc; addr++) {
+ nic->eeprom[addr] = e100_eeprom_read(nic, &addr_len, addr);
+ if (addr < nic->eeprom_wc - 1)
+ checksum += le16_to_cpu(nic->eeprom[addr]);
+ }
+
+ /* The checksum, stored in the last word, is calculated such that
+ * the sum of words should be 0xBABA */
+ if (cpu_to_le16(0xBABA - checksum) != nic->eeprom[nic->eeprom_wc - 1]) {
+ netif_err(nic, probe, nic->netdev, "EEPROM corrupted\n");
+ if (!eeprom_bad_csum_allow)
+ return -EAGAIN;
+ }
+
+ return 0;
+}
+
+/* Save (portion of) driver EEPROM cache to device and update checksum */
+static int e100_eeprom_save(struct nic *nic, u16 start, u16 count)
+{
+ u16 addr, addr_len = 8, checksum = 0;
+
+ /* Try reading with an 8-bit addr len to discover actual addr len */
+ e100_eeprom_read(nic, &addr_len, 0);
+ nic->eeprom_wc = 1 << addr_len;
+
+ if (start + count >= nic->eeprom_wc)
+ return -EINVAL;
+
+ for (addr = start; addr < start + count; addr++)
+ e100_eeprom_write(nic, addr_len, addr, nic->eeprom[addr]);
+
+ /* The checksum, stored in the last word, is calculated such that
+ * the sum of words should be 0xBABA */
+ for (addr = 0; addr < nic->eeprom_wc - 1; addr++)
+ checksum += le16_to_cpu(nic->eeprom[addr]);
+ nic->eeprom[nic->eeprom_wc - 1] = cpu_to_le16(0xBABA - checksum);
+ e100_eeprom_write(nic, addr_len, nic->eeprom_wc - 1,
+ nic->eeprom[nic->eeprom_wc - 1]);
+
+ return 0;
+}
+
+#define E100_WAIT_SCB_TIMEOUT 20000 /* we might have to wait 100ms!!! */
+#define E100_WAIT_SCB_FAST 20 /* delay like the old code */
+static int e100_exec_cmd(struct nic *nic, u8 cmd, dma_addr_t dma_addr)
+{
+ unsigned long flags;
+ unsigned int i;
+ int err = 0;
+
+ spin_lock_irqsave(&nic->cmd_lock, flags);
+
+ /* Previous command is accepted when SCB clears */
+ for (i = 0; i < E100_WAIT_SCB_TIMEOUT; i++) {
+ if (likely(!ioread8(&nic->csr->scb.cmd_lo)))
+ break;
+ cpu_relax();
+ if (unlikely(i > E100_WAIT_SCB_FAST))
+ udelay(5);
+ }
+ if (unlikely(i == E100_WAIT_SCB_TIMEOUT)) {
+ err = -EAGAIN;
+ goto err_unlock;
+ }
+
+ if (unlikely(cmd != cuc_resume))
+ iowrite32(dma_addr, &nic->csr->scb.gen_ptr);
+ iowrite8(cmd, &nic->csr->scb.cmd_lo);
+
+err_unlock:
+ spin_unlock_irqrestore(&nic->cmd_lock, flags);
+
+ return err;
+}
+
+static int e100_exec_cb(struct nic *nic, struct sk_buff *skb,
+ void (*cb_prepare)(struct nic *, struct cb *, struct sk_buff *))
+{
+ struct cb *cb;
+ unsigned long flags;
+ int err = 0;
+
+ spin_lock_irqsave(&nic->cb_lock, flags);
+
+ if (unlikely(!nic->cbs_avail)) {
+ err = -ENOMEM;
+ goto err_unlock;
+ }
+
+ cb = nic->cb_to_use;
+ nic->cb_to_use = cb->next;
+ nic->cbs_avail--;
+ cb->skb = skb;
+
+ if (unlikely(!nic->cbs_avail))
+ err = -ENOSPC;
+
+ cb_prepare(nic, cb, skb);
+
+ /* Order is important otherwise we'll be in a race with h/w:
+ * set S-bit in current first, then clear S-bit in previous. */
+ cb->command |= cpu_to_le16(cb_s);
+ wmb();
+ cb->prev->command &= cpu_to_le16(~cb_s);
+
+ while (nic->cb_to_send != nic->cb_to_use) {
+ if (unlikely(e100_exec_cmd(nic, nic->cuc_cmd,
+ nic->cb_to_send->dma_addr))) {
+ /* Ok, here's where things get sticky. It's
+ * possible that we can't schedule the command
+ * because the controller is too busy, so
+ * let's just queue the command and try again
+ * when another command is scheduled. */
+ if (err == -ENOSPC) {
+ //request a reset
+ schedule_work(&nic->tx_timeout_task);
+ }
+ break;
+ } else {
+ nic->cuc_cmd = cuc_resume;
+ nic->cb_to_send = nic->cb_to_send->next;
+ }
+ }
+
+err_unlock:
+ spin_unlock_irqrestore(&nic->cb_lock, flags);
+
+ return err;
+}
+
+static int mdio_read(struct net_device *netdev, int addr, int reg)
+{
+ struct nic *nic = netdev_priv(netdev);
+ return nic->mdio_ctrl(nic, addr, mdi_read, reg, 0);
+}
+
+static void mdio_write(struct net_device *netdev, int addr, int reg, int data)
+{
+ struct nic *nic = netdev_priv(netdev);
+
+ nic->mdio_ctrl(nic, addr, mdi_write, reg, data);
+}
+
+/* the standard mdio_ctrl() function for usual MII-compliant hardware */
+static u16 mdio_ctrl_hw(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data)
+{
+ u32 data_out = 0;
+ unsigned int i;
+ unsigned long flags;
+
+
+ /*
+ * Stratus87247: we shouldn't be writing the MDI control
+ * register until the Ready bit shows True. Also, since
+ * manipulation of the MDI control registers is a multi-step
+ * procedure it should be done under lock.
+ */
+ spin_lock_irqsave(&nic->mdio_lock, flags);
+ for (i = 100; i; --i) {
+ if (ioread32(&nic->csr->mdi_ctrl) & mdi_ready)
+ break;
+ udelay(20);
+ }
+ if (unlikely(!i)) {
+ netdev_err(nic->netdev, "e100.mdio_ctrl won't go Ready\n");
+ spin_unlock_irqrestore(&nic->mdio_lock, flags);
+ return 0; /* No way to indicate timeout error */
+ }
+ iowrite32((reg << 16) | (addr << 21) | dir | data, &nic->csr->mdi_ctrl);
+
+ for (i = 0; i < 100; i++) {
+ udelay(20);
+ if ((data_out = ioread32(&nic->csr->mdi_ctrl)) & mdi_ready)
+ break;
+ }
+ spin_unlock_irqrestore(&nic->mdio_lock, flags);
+ netif_printk(nic, hw, KERN_DEBUG, nic->netdev,
+ "%s:addr=%d, reg=%d, data_in=0x%04X, data_out=0x%04X\n",
+ dir == mdi_read ? "READ" : "WRITE",
+ addr, reg, data, data_out);
+ return (u16)data_out;
+}
+
+/* slightly tweaked mdio_ctrl() function for phy_82552_v specifics */
+static u16 mdio_ctrl_phy_82552_v(struct nic *nic,
+ u32 addr,
+ u32 dir,
+ u32 reg,
+ u16 data)
+{
+ if ((reg == MII_BMCR) && (dir == mdi_write)) {
+ if (data & (BMCR_ANRESTART | BMCR_ANENABLE)) {
+ u16 advert = mdio_read(nic->netdev, nic->mii.phy_id,
+ MII_ADVERTISE);
+
+ /*
+ * Workaround Si issue where sometimes the part will not
+ * autoneg to 100Mbps even when advertised.
+ */
+ if (advert & ADVERTISE_100FULL)
+ data |= BMCR_SPEED100 | BMCR_FULLDPLX;
+ else if (advert & ADVERTISE_100HALF)
+ data |= BMCR_SPEED100;
+ }
+ }
+ return mdio_ctrl_hw(nic, addr, dir, reg, data);
+}
+
+/* Fully software-emulated mdio_ctrl() function for cards without
+ * MII-compliant PHYs.
+ * For now, this is mainly geared towards 80c24 support; in case of further
+ * requirements for other types (i82503, ...?) either extend this mechanism
+ * or split it, whichever is cleaner.
+ */
+static u16 mdio_ctrl_phy_mii_emulated(struct nic *nic,
+ u32 addr,
+ u32 dir,
+ u32 reg,
+ u16 data)
+{
+ /* might need to allocate a netdev_priv'ed register array eventually
+ * to be able to record state changes, but for now
+ * some fully hardcoded register handling ought to be ok I guess. */
+
+ if (dir == mdi_read) {
+ switch (reg) {
+ case MII_BMCR:
+ /* Auto-negotiation, right? */
+ return BMCR_ANENABLE |
+ BMCR_FULLDPLX;
+ case MII_BMSR:
+ return BMSR_LSTATUS /* for mii_link_ok() */ |
+ BMSR_ANEGCAPABLE |
+ BMSR_10FULL;
+ case MII_ADVERTISE:
+ /* 80c24 is a "combo card" PHY, right? */
+ return ADVERTISE_10HALF |
+ ADVERTISE_10FULL;
+ default:
+ netif_printk(nic, hw, KERN_DEBUG, nic->netdev,
+ "%s:addr=%d, reg=%d, data=0x%04X: unimplemented emulation!\n",
+ dir == mdi_read ? "READ" : "WRITE",
+ addr, reg, data);
+ return 0xFFFF;
+ }
+ } else {
+ switch (reg) {
+ default:
+ netif_printk(nic, hw, KERN_DEBUG, nic->netdev,
+ "%s:addr=%d, reg=%d, data=0x%04X: unimplemented emulation!\n",
+ dir == mdi_read ? "READ" : "WRITE",
+ addr, reg, data);
+ return 0xFFFF;
+ }
+ }
+}
+static inline int e100_phy_supports_mii(struct nic *nic)
+{
+ /* for now, just check it by comparing whether we
+ are using MII software emulation.
+ */
+ return (nic->mdio_ctrl != mdio_ctrl_phy_mii_emulated);
+}
+
+static void e100_get_defaults(struct nic *nic)
+{
+ struct param_range rfds = { .min = 16, .max = 256, .count = 256 };
+ struct param_range cbs = { .min = 64, .max = 256, .count = 128 };
+
+ /* MAC type is encoded as rev ID; exception: ICH is treated as 82559 */
+ nic->mac = (nic->flags & ich) ? mac_82559_D101M : nic->pdev->revision;
+ if (nic->mac == mac_unknown)
+ nic->mac = mac_82557_D100_A;
+
+ nic->params.rfds = rfds;
+ nic->params.cbs = cbs;
+
+ /* Quadwords to DMA into FIFO before starting frame transmit */
+ nic->tx_threshold = 0xE0;
+
+ /* no interrupt for every tx completion, delay = 256us if not 557 */
+ nic->tx_command = cpu_to_le16(cb_tx | cb_tx_sf |
+ ((nic->mac >= mac_82558_D101_A4) ? cb_cid : cb_i));
+
+ /* Template for a freshly allocated RFD */
+ nic->blank_rfd.command = 0;
+ nic->blank_rfd.rbd = cpu_to_le32(0xFFFFFFFF);
+ nic->blank_rfd.size = cpu_to_le16(VLAN_ETH_FRAME_LEN);
+
+ /* MII setup */
+ nic->mii.phy_id_mask = 0x1F;
+ nic->mii.reg_num_mask = 0x1F;
+ nic->mii.dev = nic->netdev;
+ nic->mii.mdio_read = mdio_read;
+ nic->mii.mdio_write = mdio_write;
+}
+
+static void e100_configure(struct nic *nic, struct cb *cb, struct sk_buff *skb)
+{
+ struct config *config = &cb->u.config;
+ u8 *c = (u8 *)config;
+
+ cb->command = cpu_to_le16(cb_config);
+
+ memset(config, 0, sizeof(struct config));
+
+ config->byte_count = 0x16; /* bytes in this struct */
+ config->rx_fifo_limit = 0x8; /* bytes in FIFO before DMA */
+ config->direct_rx_dma = 0x1; /* reserved */
+ config->standard_tcb = 0x1; /* 1=standard, 0=extended */
+ config->standard_stat_counter = 0x1; /* 1=standard, 0=extended */
+ config->rx_discard_short_frames = 0x1; /* 1=discard, 0=pass */
+ config->tx_underrun_retry = 0x3; /* # of underrun retries */
+ if (e100_phy_supports_mii(nic))
+ config->mii_mode = 1; /* 1=MII mode, 0=i82503 mode */
+ config->pad10 = 0x6;
+ config->no_source_addr_insertion = 0x1; /* 1=no, 0=yes */
+ config->preamble_length = 0x2; /* 0=1, 1=3, 2=7, 3=15 bytes */
+ config->ifs = 0x6; /* x16 = inter frame spacing */
+ config->ip_addr_hi = 0xF2; /* ARP IP filter - not used */
+ config->pad15_1 = 0x1;
+ config->pad15_2 = 0x1;
+ config->crs_or_cdt = 0x0; /* 0=CRS only, 1=CRS or CDT */
+ config->fc_delay_hi = 0x40; /* time delay for fc frame */
+ config->tx_padding = 0x1; /* 1=pad short frames */
+ config->fc_priority_threshold = 0x7; /* 7=priority fc disabled */
+ config->pad18 = 0x1;
+ config->full_duplex_pin = 0x1; /* 1=examine FDX# pin */
+ config->pad20_1 = 0x1F;
+ config->fc_priority_location = 0x1; /* 1=byte#31, 0=byte#19 */
+ config->pad21_1 = 0x5;
+
+ config->adaptive_ifs = nic->adaptive_ifs;
+ config->loopback = nic->loopback;
+
+ if (nic->mii.force_media && nic->mii.full_duplex)
+ config->full_duplex_force = 0x1; /* 1=force, 0=auto */
+
+ if (nic->flags & promiscuous || nic->loopback) {
+ config->rx_save_bad_frames = 0x1; /* 1=save, 0=discard */
+ config->rx_discard_short_frames = 0x0; /* 1=discard, 0=save */
+ config->promiscuous_mode = 0x1; /* 1=on, 0=off */
+ }
+
+ if (nic->flags & multicast_all)
+ config->multicast_all = 0x1; /* 1=accept, 0=no */
+
+ /* disable WoL when up */
+ if (netif_running(nic->netdev) || !(nic->flags & wol_magic))
+ config->magic_packet_disable = 0x1; /* 1=off, 0=on */
+
+ if (nic->mac >= mac_82558_D101_A4) {
+ config->fc_disable = 0x1; /* 1=Tx fc off, 0=Tx fc on */
+ config->mwi_enable = 0x1; /* 1=enable, 0=disable */
+ config->standard_tcb = 0x0; /* 1=standard, 0=extended */
+ config->rx_long_ok = 0x1; /* 1=VLANs ok, 0=standard */
+ if (nic->mac >= mac_82559_D101M) {
+ config->tno_intr = 0x1; /* TCO stats enable */
+ /* Enable TCO in extended config */
+ if (nic->mac >= mac_82551_10) {
+ config->byte_count = 0x20; /* extended bytes */
+ config->rx_d102_mode = 0x1; /* GMRC for TCO */
+ }
+ } else {
+ config->standard_stat_counter = 0x0;
+ }
+ }
+
+ netif_printk(nic, hw, KERN_DEBUG, nic->netdev,
+ "[00-07]=%02X:%02X:%02X:%02X:%02X:%02X:%02X:%02X\n",
+ c[0], c[1], c[2], c[3], c[4], c[5], c[6], c[7]);
+ netif_printk(nic, hw, KERN_DEBUG, nic->netdev,
+ "[08-15]=%02X:%02X:%02X:%02X:%02X:%02X:%02X:%02X\n",
+ c[8], c[9], c[10], c[11], c[12], c[13], c[14], c[15]);
+ netif_printk(nic, hw, KERN_DEBUG, nic->netdev,
+ "[16-23]=%02X:%02X:%02X:%02X:%02X:%02X:%02X:%02X\n",
+ c[16], c[17], c[18], c[19], c[20], c[21], c[22], c[23]);
+}
+
+/*************************************************************************
+* CPUSaver parameters
+*
+* All CPUSaver parameters are 16-bit literals that are part of a
+* "move immediate value" instruction. By changing the value of
+* the literal in the instruction before the code is loaded, the
+* driver can change the algorithm.
+*
+* INTDELAY - This loads the dead-man timer with its initial value.
+* When this timer expires the interrupt is asserted, and the
+* timer is reset each time a new packet is received. (see
+* BUNDLEMAX below to set the limit on number of chained packets)
+* The current default is 0x600 or 1536. Experiments show that
+* the value should probably stay within the 0x200 - 0x1000.
+*
+* BUNDLEMAX -
+* This sets the maximum number of frames that will be bundled. In
+* some situations, such as the TCP windowing algorithm, it may be
+* better to limit the growth of the bundle size than let it go as
+* high as it can, because that could cause too much added latency.
+* The default is six, because this is the number of packets in the
+* default TCP window size. A value of 1 would make CPUSaver indicate
+* an interrupt for every frame received. If you do not want to put
+* a limit on the bundle size, set this value to xFFFF.
+*
+* BUNDLESMALL -
+* This contains a bit-mask describing the minimum size frame that
+* will be bundled. The default masks the lower 7 bits, which means
+* that any frame less than 128 bytes in length will not be bundled,
+* but will instead immediately generate an interrupt. This does
+* not affect the current bundle in any way. Any frame that is 128
+* bytes or large will be bundled normally. This feature is meant
+* to provide immediate indication of ACK frames in a TCP environment.
+* Customers were seeing poor performance when a machine with CPUSaver
+* enabled was sending but not receiving. The delay introduced when
+* the ACKs were received was enough to reduce total throughput, because
+* the sender would sit idle until the ACK was finally seen.
+*
+* The current default is 0xFF80, which masks out the lower 7 bits.
+* This means that any frame which is x7F (127) bytes or smaller
+* will cause an immediate interrupt. Because this value must be a
+* bit mask, there are only a few valid values that can be used. To
+* turn this feature off, the driver can write the value xFFFF to the
+* lower word of this instruction (in the same way that the other
+* parameters are used). Likewise, a value of 0xF800 (2047) would
+* cause an interrupt to be generated for every frame, because all
+* standard Ethernet frames are <= 2047 bytes in length.
+*************************************************************************/
+
+/* if you wish to disable the ucode functionality, while maintaining the
+ * workarounds it provides, set the following defines to:
+ * BUNDLESMALL 0
+ * BUNDLEMAX 1
+ * INTDELAY 1
+ */
+#define BUNDLESMALL 1
+#define BUNDLEMAX (u16)6
+#define INTDELAY (u16)1536 /* 0x600 */
+
+/* Initialize firmware */
+static const struct firmware *e100_request_firmware(struct nic *nic)
+{
+ const char *fw_name;
+ const struct firmware *fw = nic->fw;
+ u8 timer, bundle, min_size;
+ int err = 0;
+
+ /* do not load u-code for ICH devices */
+ if (nic->flags & ich)
+ return NULL;
+
+ /* Search for ucode match against h/w revision */
+ if (nic->mac == mac_82559_D101M)
+ fw_name = FIRMWARE_D101M;
+ else if (nic->mac == mac_82559_D101S)
+ fw_name = FIRMWARE_D101S;
+ else if (nic->mac == mac_82551_F || nic->mac == mac_82551_10)
+ fw_name = FIRMWARE_D102E;
+ else /* No ucode on other devices */
+ return NULL;
+
+ /* If the firmware has not previously been loaded, request a pointer
+ * to it. If it was previously loaded, we are reinitializing the
+ * adapter, possibly in a resume from hibernate, in which case
+ * request_firmware() cannot be used.
+ */
+ if (!fw)
+ err = request_firmware(&fw, fw_name, &nic->pdev->dev);
+
+ if (err) {
+ netif_err(nic, probe, nic->netdev,
+ "Failed to load firmware \"%s\": %d\n",
+ fw_name, err);
+ return ERR_PTR(err);
+ }
+
+ /* Firmware should be precisely UCODE_SIZE (words) plus three bytes
+ indicating the offsets for BUNDLESMALL, BUNDLEMAX, INTDELAY */
+ if (fw->size != UCODE_SIZE * 4 + 3) {
+ netif_err(nic, probe, nic->netdev,
+ "Firmware \"%s\" has wrong size %zu\n",
+ fw_name, fw->size);
+ release_firmware(fw);
+ return ERR_PTR(-EINVAL);
+ }
+
+ /* Read timer, bundle and min_size from end of firmware blob */
+ timer = fw->data[UCODE_SIZE * 4];
+ bundle = fw->data[UCODE_SIZE * 4 + 1];
+ min_size = fw->data[UCODE_SIZE * 4 + 2];
+
+ if (timer >= UCODE_SIZE || bundle >= UCODE_SIZE ||
+ min_size >= UCODE_SIZE) {
+ netif_err(nic, probe, nic->netdev,
+ "\"%s\" has bogus offset values (0x%x,0x%x,0x%x)\n",
+ fw_name, timer, bundle, min_size);
+ release_firmware(fw);
+ return ERR_PTR(-EINVAL);
+ }
+
+ /* OK, firmware is validated and ready to use. Save a pointer
+ * to it in the nic */
+ nic->fw = fw;
+ return fw;
+}
+
+static void e100_setup_ucode(struct nic *nic, struct cb *cb,
+ struct sk_buff *skb)
+{
+ const struct firmware *fw = (void *)skb;
+ u8 timer, bundle, min_size;
+
+ /* It's not a real skb; we just abused the fact that e100_exec_cb
+ will pass it through to here... */
+ cb->skb = NULL;
+
+ /* firmware is stored as little endian already */
+ memcpy(cb->u.ucode, fw->data, UCODE_SIZE * 4);
+
+ /* Read timer, bundle and min_size from end of firmware blob */
+ timer = fw->data[UCODE_SIZE * 4];
+ bundle = fw->data[UCODE_SIZE * 4 + 1];
+ min_size = fw->data[UCODE_SIZE * 4 + 2];
+
+ /* Insert user-tunable settings in cb->u.ucode */
+ cb->u.ucode[timer] &= cpu_to_le32(0xFFFF0000);
+ cb->u.ucode[timer] |= cpu_to_le32(INTDELAY);
+ cb->u.ucode[bundle] &= cpu_to_le32(0xFFFF0000);
+ cb->u.ucode[bundle] |= cpu_to_le32(BUNDLEMAX);
+ cb->u.ucode[min_size] &= cpu_to_le32(0xFFFF0000);
+ cb->u.ucode[min_size] |= cpu_to_le32((BUNDLESMALL) ? 0xFFFF : 0xFF80);
+
+ cb->command = cpu_to_le16(cb_ucode | cb_el);
+}
+
+static inline int e100_load_ucode_wait(struct nic *nic)
+{
+ const struct firmware *fw;
+ int err = 0, counter = 50;
+ struct cb *cb = nic->cb_to_clean;
+
+ fw = e100_request_firmware(nic);
+ /* If it's NULL, then no ucode is required */
+ if (!fw || IS_ERR(fw))
+ return PTR_ERR(fw);
+
+ if ((err = e100_exec_cb(nic, (void *)fw, e100_setup_ucode)))
+ netif_err(nic, probe, nic->netdev,
+ "ucode cmd failed with error %d\n", err);
+
+ /* must restart cuc */
+ nic->cuc_cmd = cuc_start;
+
+ /* wait for completion */
+ e100_write_flush(nic);
+ udelay(10);
+
+ /* wait for possibly (ouch) 500ms */
+ while (!(cb->status & cpu_to_le16(cb_complete))) {
+ msleep(10);
+ if (!--counter) break;
+ }
+
+ /* ack any interrupts, something could have been set */
+ iowrite8(~0, &nic->csr->scb.stat_ack);
+
+ /* if the command failed, or is not OK, notify and return */
+ if (!counter || !(cb->status & cpu_to_le16(cb_ok))) {
+ netif_err(nic, probe, nic->netdev, "ucode load failed\n");
+ err = -EPERM;
+ }
+
+ return err;
+}
+
+static void e100_setup_iaaddr(struct nic *nic, struct cb *cb,
+ struct sk_buff *skb)
+{
+ cb->command = cpu_to_le16(cb_iaaddr);
+ memcpy(cb->u.iaaddr, nic->netdev->dev_addr, ETH_ALEN);
+}
+
+static void e100_dump(struct nic *nic, struct cb *cb, struct sk_buff *skb)
+{
+ cb->command = cpu_to_le16(cb_dump);
+ cb->u.dump_buffer_addr = cpu_to_le32(nic->dma_addr +
+ offsetof(struct mem, dump_buf));
+}
+
+static int e100_phy_check_without_mii(struct nic *nic)
+{
+ u8 phy_type;
+ int without_mii;
+
+ phy_type = (nic->eeprom[eeprom_phy_iface] >> 8) & 0x0f;
+
+ switch (phy_type) {
+ case NoSuchPhy: /* Non-MII PHY; UNTESTED! */
+ case I82503: /* Non-MII PHY; UNTESTED! */
+ case S80C24: /* Non-MII PHY; tested and working */
+ /* paragraph from the FreeBSD driver, "FXP_PHY_80C24":
+ * The Seeq 80c24 AutoDUPLEX(tm) Ethernet Interface Adapter
+ * doesn't have a programming interface of any sort. The
+ * media is sensed automatically based on how the link partner
+ * is configured. This is, in essence, manual configuration.
+ */
+ netif_info(nic, probe, nic->netdev,
+ "found MII-less i82503 or 80c24 or other PHY\n");
+
+ nic->mdio_ctrl = mdio_ctrl_phy_mii_emulated;
+ nic->mii.phy_id = 0; /* is this ok for an MII-less PHY? */
+
+ /* these might be needed for certain MII-less cards...
+ * nic->flags |= ich;
+ * nic->flags |= ich_10h_workaround; */
+
+ without_mii = 1;
+ break;
+ default:
+ without_mii = 0;
+ break;
+ }
+ return without_mii;
+}
+
+#define NCONFIG_AUTO_SWITCH 0x0080
+#define MII_NSC_CONG MII_RESV1
+#define NSC_CONG_ENABLE 0x0100
+#define NSC_CONG_TXREADY 0x0400
+#define ADVERTISE_FC_SUPPORTED 0x0400
+static int e100_phy_init(struct nic *nic)
+{
+ struct net_device *netdev = nic->netdev;
+ u32 addr;
+ u16 bmcr, stat, id_lo, id_hi, cong;
+
+ /* Discover phy addr by searching addrs in order {1,0,2,..., 31} */
+ for (addr = 0; addr < 32; addr++) {
+ nic->mii.phy_id = (addr == 0) ? 1 : (addr == 1) ? 0 : addr;
+ bmcr = mdio_read(netdev, nic->mii.phy_id, MII_BMCR);
+ stat = mdio_read(netdev, nic->mii.phy_id, MII_BMSR);
+ stat = mdio_read(netdev, nic->mii.phy_id, MII_BMSR);
+ if (!((bmcr == 0xFFFF) || ((stat == 0) && (bmcr == 0))))
+ break;
+ }
+ if (addr == 32) {
+ /* uhoh, no PHY detected: check whether we seem to be some
+ * weird, rare variant which is *known* to not have any MII.
+ * But do this AFTER MII checking only, since this does
+ * lookup of EEPROM values which may easily be unreliable. */
+ if (e100_phy_check_without_mii(nic))
+ return 0; /* simply return and hope for the best */
+ else {
+ /* for unknown cases log a fatal error */
+ netif_err(nic, hw, nic->netdev,
+ "Failed to locate any known PHY, aborting\n");
+ return -EAGAIN;
+ }
+ } else
+ netif_printk(nic, hw, KERN_DEBUG, nic->netdev,
+ "phy_addr = %d\n", nic->mii.phy_id);
+
+ /* Get phy ID */
+ id_lo = mdio_read(netdev, nic->mii.phy_id, MII_PHYSID1);
+ id_hi = mdio_read(netdev, nic->mii.phy_id, MII_PHYSID2);
+ nic->phy = (u32)id_hi << 16 | (u32)id_lo;
+ netif_printk(nic, hw, KERN_DEBUG, nic->netdev,
+ "phy ID = 0x%08X\n", nic->phy);
+
+ /* Select the phy and isolate the rest */
+ for (addr = 0; addr < 32; addr++) {
+ if (addr != nic->mii.phy_id) {
+ mdio_write(netdev, addr, MII_BMCR, BMCR_ISOLATE);
+ } else if (nic->phy != phy_82552_v) {
+ bmcr = mdio_read(netdev, addr, MII_BMCR);
+ mdio_write(netdev, addr, MII_BMCR,
+ bmcr & ~BMCR_ISOLATE);
+ }
+ }
+ /*
+ * Workaround for 82552:
+ * Clear the ISOLATE bit on selected phy_id last (mirrored on all
+ * other phy_id's) using bmcr value from addr discovery loop above.
+ */
+ if (nic->phy == phy_82552_v)
+ mdio_write(netdev, nic->mii.phy_id, MII_BMCR,
+ bmcr & ~BMCR_ISOLATE);
+
+ /* Handle National tx phys */
+#define NCS_PHY_MODEL_MASK 0xFFF0FFFF
+ if ((nic->phy & NCS_PHY_MODEL_MASK) == phy_nsc_tx) {
+ /* Disable congestion control */
+ cong = mdio_read(netdev, nic->mii.phy_id, MII_NSC_CONG);
+ cong |= NSC_CONG_TXREADY;
+ cong &= ~NSC_CONG_ENABLE;
+ mdio_write(netdev, nic->mii.phy_id, MII_NSC_CONG, cong);
+ }
+
+ if (nic->phy == phy_82552_v) {
+ u16 advert = mdio_read(netdev, nic->mii.phy_id, MII_ADVERTISE);
+
+ /* assign special tweaked mdio_ctrl() function */
+ nic->mdio_ctrl = mdio_ctrl_phy_82552_v;
+
+ /* Workaround Si not advertising flow-control during autoneg */
+ advert |= ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM;
+ mdio_write(netdev, nic->mii.phy_id, MII_ADVERTISE, advert);
+
+ /* Reset for the above changes to take effect */
+ bmcr = mdio_read(netdev, nic->mii.phy_id, MII_BMCR);
+ bmcr |= BMCR_RESET;
+ mdio_write(netdev, nic->mii.phy_id, MII_BMCR, bmcr);
+ } else if ((nic->mac >= mac_82550_D102) || ((nic->flags & ich) &&
+ (mdio_read(netdev, nic->mii.phy_id, MII_TPISTATUS) & 0x8000) &&
+ !(nic->eeprom[eeprom_cnfg_mdix] & eeprom_mdix_enabled))) {
+ /* enable/disable MDI/MDI-X auto-switching. */
+ mdio_write(netdev, nic->mii.phy_id, MII_NCONFIG,
+ nic->mii.force_media ? 0 : NCONFIG_AUTO_SWITCH);
+ }
+
+ return 0;
+}
+
+static int e100_hw_init(struct nic *nic)
+{
+ int err;
+
+ e100_hw_reset(nic);
+
+ netif_err(nic, hw, nic->netdev, "e100_hw_init\n");
+ if (!in_interrupt() && (err = e100_self_test(nic)))
+ return err;
+
+ if ((err = e100_phy_init(nic)))
+ return err;
+ if ((err = e100_exec_cmd(nic, cuc_load_base, 0)))
+ return err;
+ if ((err = e100_exec_cmd(nic, ruc_load_base, 0)))
+ return err;
+ if ((err = e100_load_ucode_wait(nic)))
+ return err;
+ if ((err = e100_exec_cb(nic, NULL, e100_configure)))
+ return err;
+ if ((err = e100_exec_cb(nic, NULL, e100_setup_iaaddr)))
+ return err;
+ if ((err = e100_exec_cmd(nic, cuc_dump_addr,
+ nic->dma_addr + offsetof(struct mem, stats))))
+ return err;
+ if ((err = e100_exec_cmd(nic, cuc_dump_reset, 0)))
+ return err;
+
+ e100_disable_irq(nic);
+
+ return 0;
+}
+
+static void e100_multi(struct nic *nic, struct cb *cb, struct sk_buff *skb)
+{
+ struct net_device *netdev = nic->netdev;
+ struct netdev_hw_addr *ha;
+ u16 i, count = min(netdev_mc_count(netdev), E100_MAX_MULTICAST_ADDRS);
+
+ cb->command = cpu_to_le16(cb_multi);
+ cb->u.multi.count = cpu_to_le16(count * ETH_ALEN);
+ i = 0;
+ netdev_for_each_mc_addr(ha, netdev) {
+ if (i == count)
+ break;
+ memcpy(&cb->u.multi.addr[i++ * ETH_ALEN], &ha->addr,
+ ETH_ALEN);
+ }
+}
+
+static void e100_set_multicast_list(struct net_device *netdev)
+{
+ struct nic *nic = netdev_priv(netdev);
+
+ netif_printk(nic, hw, KERN_DEBUG, nic->netdev,
+ "mc_count=%d, flags=0x%04X\n",
+ netdev_mc_count(netdev), netdev->flags);
+
+ if (netdev->flags & IFF_PROMISC)
+ nic->flags |= promiscuous;
+ else
+ nic->flags &= ~promiscuous;
+
+ if (netdev->flags & IFF_ALLMULTI ||
+ netdev_mc_count(netdev) > E100_MAX_MULTICAST_ADDRS)
+ nic->flags |= multicast_all;
+ else
+ nic->flags &= ~multicast_all;
+
+ e100_exec_cb(nic, NULL, e100_configure);
+ e100_exec_cb(nic, NULL, e100_multi);
+}
+
+static void e100_update_stats(struct nic *nic)
+{
+ struct net_device *dev = nic->netdev;
+ struct net_device_stats *ns = &dev->stats;
+ struct stats *s = &nic->mem->stats;
+ __le32 *complete = (nic->mac < mac_82558_D101_A4) ? &s->fc_xmt_pause :
+ (nic->mac < mac_82559_D101M) ? (__le32 *)&s->xmt_tco_frames :
+ &s->complete;
+
+ /* Device's stats reporting may take several microseconds to
+ * complete, so we're always waiting for results of the
+ * previous command. */
+
+ if (*complete == cpu_to_le32(cuc_dump_reset_complete)) {
+ *complete = 0;
+ nic->tx_frames = le32_to_cpu(s->tx_good_frames);
+ nic->tx_collisions = le32_to_cpu(s->tx_total_collisions);
+ ns->tx_aborted_errors += le32_to_cpu(s->tx_max_collisions);
+ ns->tx_window_errors += le32_to_cpu(s->tx_late_collisions);
+ ns->tx_carrier_errors += le32_to_cpu(s->tx_lost_crs);
+ ns->tx_fifo_errors += le32_to_cpu(s->tx_underruns);
+ ns->collisions += nic->tx_collisions;
+ ns->tx_errors += le32_to_cpu(s->tx_max_collisions) +
+ le32_to_cpu(s->tx_lost_crs);
+ ns->rx_length_errors += le32_to_cpu(s->rx_short_frame_errors) +
+ nic->rx_over_length_errors;
+ ns->rx_crc_errors += le32_to_cpu(s->rx_crc_errors);
+ ns->rx_frame_errors += le32_to_cpu(s->rx_alignment_errors);
+ ns->rx_over_errors += le32_to_cpu(s->rx_overrun_errors);
+ ns->rx_fifo_errors += le32_to_cpu(s->rx_overrun_errors);
+ ns->rx_missed_errors += le32_to_cpu(s->rx_resource_errors);
+ ns->rx_errors += le32_to_cpu(s->rx_crc_errors) +
+ le32_to_cpu(s->rx_alignment_errors) +
+ le32_to_cpu(s->rx_short_frame_errors) +
+ le32_to_cpu(s->rx_cdt_errors);
+ nic->tx_deferred += le32_to_cpu(s->tx_deferred);
+ nic->tx_single_collisions +=
+ le32_to_cpu(s->tx_single_collisions);
+ nic->tx_multiple_collisions +=
+ le32_to_cpu(s->tx_multiple_collisions);
+ if (nic->mac >= mac_82558_D101_A4) {
+ nic->tx_fc_pause += le32_to_cpu(s->fc_xmt_pause);
+ nic->rx_fc_pause += le32_to_cpu(s->fc_rcv_pause);
+ nic->rx_fc_unsupported +=
+ le32_to_cpu(s->fc_rcv_unsupported);
+ if (nic->mac >= mac_82559_D101M) {
+ nic->tx_tco_frames +=
+ le16_to_cpu(s->xmt_tco_frames);
+ nic->rx_tco_frames +=
+ le16_to_cpu(s->rcv_tco_frames);
+ }
+ }
+ }
+
+
+ if (e100_exec_cmd(nic, cuc_dump_reset, 0))
+ netif_printk(nic, tx_err, KERN_DEBUG, nic->netdev,
+ "exec cuc_dump_reset failed\n");
+}
+
+static void e100_adjust_adaptive_ifs(struct nic *nic, int speed, int duplex)
+{
+ /* Adjust inter-frame-spacing (IFS) between two transmits if
+ * we're getting collisions on a half-duplex connection. */
+
+ if (duplex == DUPLEX_HALF) {
+ u32 prev = nic->adaptive_ifs;
+ u32 min_frames = (speed == SPEED_100) ? 1000 : 100;
+
+ if ((nic->tx_frames / 32 < nic->tx_collisions) &&
+ (nic->tx_frames > min_frames)) {
+ if (nic->adaptive_ifs < 60)
+ nic->adaptive_ifs += 5;
+ } else if (nic->tx_frames < min_frames) {
+ if (nic->adaptive_ifs >= 5)
+ nic->adaptive_ifs -= 5;
+ }
+ if (nic->adaptive_ifs != prev)
+ e100_exec_cb(nic, NULL, e100_configure);
+ }
+}
+
+static void e100_watchdog(unsigned long data)
+{
+ struct nic *nic = (struct nic *)data;
+ struct ethtool_cmd cmd;
+
+ netif_printk(nic, timer, KERN_DEBUG, nic->netdev,
+ "right now = %ld\n", jiffies);
+
+ /* mii library handles link maintenance tasks */
+
+ mii_ethtool_gset(&nic->mii, &cmd);
+
+ if (mii_link_ok(&nic->mii) && !netif_carrier_ok(nic->netdev)) {
+ netdev_info(nic->netdev, "NIC Link is Up %u Mbps %s Duplex\n",
+ cmd.speed == SPEED_100 ? 100 : 10,
+ cmd.duplex == DUPLEX_FULL ? "Full" : "Half");
+ } else if (!mii_link_ok(&nic->mii) && netif_carrier_ok(nic->netdev)) {
+ netdev_info(nic->netdev, "NIC Link is Down\n");
+ }
+
+ mii_check_link(&nic->mii);
+
+ /* Software generated interrupt to recover from (rare) Rx
+ * allocation failure.
+ * Unfortunately have to use a spinlock to not re-enable interrupts
+ * accidentally, due to hardware that shares a register between the
+ * interrupt mask bit and the SW Interrupt generation bit */
+ spin_lock_irq(&nic->cmd_lock);
+ iowrite8(ioread8(&nic->csr->scb.cmd_hi) | irq_sw_gen,&nic->csr->scb.cmd_hi);
+ e100_write_flush(nic);
+ spin_unlock_irq(&nic->cmd_lock);
+
+ e100_update_stats(nic);
+ e100_adjust_adaptive_ifs(nic, cmd.speed, cmd.duplex);
+
+ if (nic->mac <= mac_82557_D100_C)
+ /* Issue a multicast command to workaround a 557 lock up */
+ e100_set_multicast_list(nic->netdev);
+
+ if (nic->flags & ich && cmd.speed==SPEED_10 && cmd.duplex==DUPLEX_HALF)
+ /* Need SW workaround for ICH[x] 10Mbps/half duplex Tx hang. */
+ nic->flags |= ich_10h_workaround;
+ else
+ nic->flags &= ~ich_10h_workaround;
+
+ mod_timer(&nic->watchdog,
+ round_jiffies(jiffies + E100_WATCHDOG_PERIOD));
+}
+
+static void e100_xmit_prepare(struct nic *nic, struct cb *cb,
+ struct sk_buff *skb)
+{
+ cb->command = nic->tx_command;
+ /* interrupt every 16 packets regardless of delay */
+ if ((nic->cbs_avail & ~15) == nic->cbs_avail)
+ cb->command |= cpu_to_le16(cb_i);
+ cb->u.tcb.tbd_array = cb->dma_addr + offsetof(struct cb, u.tcb.tbd);
+ cb->u.tcb.tcb_byte_count = 0;
+ cb->u.tcb.threshold = nic->tx_threshold;
+ cb->u.tcb.tbd_count = 1;
+ cb->u.tcb.tbd.buf_addr = cpu_to_le32(pci_map_single(nic->pdev,
+ skb->data, skb->len, PCI_DMA_TODEVICE));
+ /* check for mapping failure? */
+ cb->u.tcb.tbd.size = cpu_to_le16(skb->len);
+}
+
+static netdev_tx_t e100_xmit_frame(struct sk_buff *skb,
+ struct net_device *netdev)
+{
+ struct nic *nic = netdev_priv(netdev);
+ int err;
+
+ if (nic->flags & ich_10h_workaround) {
+ /* SW workaround for ICH[x] 10Mbps/half duplex Tx hang.
+ Issue a NOP command followed by a 1us delay before
+ issuing the Tx command. */
+ if (e100_exec_cmd(nic, cuc_nop, 0))
+ netif_printk(nic, tx_err, KERN_DEBUG, nic->netdev,
+ "exec cuc_nop failed\n");
+ udelay(1);
+ }
+
+ err = e100_exec_cb(nic, skb, e100_xmit_prepare);
+
+ switch (err) {
+ case -ENOSPC:
+ /* We queued the skb, but now we're out of space. */
+ netif_printk(nic, tx_err, KERN_DEBUG, nic->netdev,
+ "No space for CB\n");
+ netif_stop_queue(netdev);
+ break;
+ case -ENOMEM:
+ /* This is a hard error - log it. */
+ netif_printk(nic, tx_err, KERN_DEBUG, nic->netdev,
+ "Out of Tx resources, returning skb\n");
+ netif_stop_queue(netdev);
+ return NETDEV_TX_BUSY;
+ }
+
+ return NETDEV_TX_OK;
+}
+
+static int e100_tx_clean(struct nic *nic)
+{
+ struct net_device *dev = nic->netdev;
+ struct cb *cb;
+ int tx_cleaned = 0;
+
+ spin_lock(&nic->cb_lock);
+
+ /* Clean CBs marked complete */
+ for (cb = nic->cb_to_clean;
+ cb->status & cpu_to_le16(cb_complete);
+ cb = nic->cb_to_clean = cb->next) {
+ rmb(); /* read skb after status */
+ netif_printk(nic, tx_done, KERN_DEBUG, nic->netdev,
+ "cb[%d]->status = 0x%04X\n",
+ (int)(((void*)cb - (void*)nic->cbs)/sizeof(struct cb)),
+ cb->status);
+
+ if (likely(cb->skb != NULL)) {
+ dev->stats.tx_packets++;
+ dev->stats.tx_bytes += cb->skb->len;
+
+ pci_unmap_single(nic->pdev,
+ le32_to_cpu(cb->u.tcb.tbd.buf_addr),
+ le16_to_cpu(cb->u.tcb.tbd.size),
+ PCI_DMA_TODEVICE);
+ dev_kfree_skb_any(cb->skb);
+ cb->skb = NULL;
+ tx_cleaned = 1;
+ }
+ cb->status = 0;
+ nic->cbs_avail++;
+ }
+
+ spin_unlock(&nic->cb_lock);
+
+ /* Recover from running out of Tx resources in xmit_frame */
+ if (unlikely(tx_cleaned && netif_queue_stopped(nic->netdev)))
+ netif_wake_queue(nic->netdev);
+
+ return tx_cleaned;
+}
+
+static void e100_clean_cbs(struct nic *nic)
+{
+ if (nic->cbs) {
+ while (nic->cbs_avail != nic->params.cbs.count) {
+ struct cb *cb = nic->cb_to_clean;
+ if (cb->skb) {
+ pci_unmap_single(nic->pdev,
+ le32_to_cpu(cb->u.tcb.tbd.buf_addr),
+ le16_to_cpu(cb->u.tcb.tbd.size),
+ PCI_DMA_TODEVICE);
+ dev_kfree_skb(cb->skb);
+ }
+ nic->cb_to_clean = nic->cb_to_clean->next;
+ nic->cbs_avail++;
+ }
+ pci_pool_free(nic->cbs_pool, nic->cbs, nic->cbs_dma_addr);
+ nic->cbs = NULL;
+ nic->cbs_avail = 0;
+ }
+ nic->cuc_cmd = cuc_start;
+ nic->cb_to_use = nic->cb_to_send = nic->cb_to_clean =
+ nic->cbs;
+}
+
+static int e100_alloc_cbs(struct nic *nic)
+{
+ struct cb *cb;
+ unsigned int i, count = nic->params.cbs.count;
+
+ nic->cuc_cmd = cuc_start;
+ nic->cb_to_use = nic->cb_to_send = nic->cb_to_clean = NULL;
+ nic->cbs_avail = 0;
+
+ nic->cbs = pci_pool_alloc(nic->cbs_pool, GFP_KERNEL,
+ &nic->cbs_dma_addr);
+ if (!nic->cbs)
+ return -ENOMEM;
+ memset(nic->cbs, 0, count * sizeof(struct cb));
+
+ for (cb = nic->cbs, i = 0; i < count; cb++, i++) {
+ cb->next = (i + 1 < count) ? cb + 1 : nic->cbs;
+ cb->prev = (i == 0) ? nic->cbs + count - 1 : cb - 1;
+
+ cb->dma_addr = nic->cbs_dma_addr + i * sizeof(struct cb);
+ cb->link = cpu_to_le32(nic->cbs_dma_addr +
+ ((i+1) % count) * sizeof(struct cb));
+ }
+
+ nic->cb_to_use = nic->cb_to_send = nic->cb_to_clean = nic->cbs;
+ nic->cbs_avail = count;
+
+ return 0;
+}
+
+static inline void e100_start_receiver(struct nic *nic, struct rx *rx)
+{
+ if (!nic->rxs) return;
+ if (RU_SUSPENDED != nic->ru_running) return;
+
+ /* handle init time starts */
+ if (!rx) rx = nic->rxs;
+
+ /* (Re)start RU if suspended or idle and RFA is non-NULL */
+ if (rx->skb) {
+ e100_exec_cmd(nic, ruc_start, rx->dma_addr);
+ nic->ru_running = RU_RUNNING;
+ }
+}
+
+#define RFD_BUF_LEN (sizeof(struct rfd) + VLAN_ETH_FRAME_LEN)
+static int e100_rx_alloc_skb(struct nic *nic, struct rx *rx)
+{
+ if (!(rx->skb = netdev_alloc_skb_ip_align(nic->netdev, RFD_BUF_LEN)))
+ return -ENOMEM;
+
+ /* Init, and map the RFD. */
+ skb_copy_to_linear_data(rx->skb, &nic->blank_rfd, sizeof(struct rfd));
+ rx->dma_addr = pci_map_single(nic->pdev, rx->skb->data,
+ RFD_BUF_LEN, PCI_DMA_BIDIRECTIONAL);
+
+ if (pci_dma_mapping_error(nic->pdev, rx->dma_addr)) {
+ dev_kfree_skb_any(rx->skb);
+ rx->skb = NULL;
+ rx->dma_addr = 0;
+ return -ENOMEM;
+ }
+
+ /* Link the RFD to end of RFA by linking previous RFD to
+ * this one. We are safe to touch the previous RFD because
+ * it is protected by the before last buffer's el bit being set */
+ if (rx->prev->skb) {
+ struct rfd *prev_rfd = (struct rfd *)rx->prev->skb->data;
+ put_unaligned_le32(rx->dma_addr, &prev_rfd->link);
+ pci_dma_sync_single_for_device(nic->pdev, rx->prev->dma_addr,
+ sizeof(struct rfd), PCI_DMA_BIDIRECTIONAL);
+ }
+
+ return 0;
+}
+
+static int e100_rx_indicate(struct nic *nic, struct rx *rx,
+ unsigned int *work_done, unsigned int work_to_do)
+{
+ struct net_device *dev = nic->netdev;
+ struct sk_buff *skb = rx->skb;
+ struct rfd *rfd = (struct rfd *)skb->data;
+ u16 rfd_status, actual_size;
+
+ if (unlikely(work_done && *work_done >= work_to_do))
+ return -EAGAIN;
+
+ /* Need to sync before taking a peek at cb_complete bit */
+ pci_dma_sync_single_for_cpu(nic->pdev, rx->dma_addr,
+ sizeof(struct rfd), PCI_DMA_BIDIRECTIONAL);
+ rfd_status = le16_to_cpu(rfd->status);
+
+ netif_printk(nic, rx_status, KERN_DEBUG, nic->netdev,
+ "status=0x%04X\n", rfd_status);
+ rmb(); /* read size after status bit */
+
+ /* If data isn't ready, nothing to indicate */
+ if (unlikely(!(rfd_status & cb_complete))) {
+ /* If the next buffer has the el bit, but we think the receiver
+ * is still running, check to see if it really stopped while
+ * we had interrupts off.
+ * This allows for a fast restart without re-enabling
+ * interrupts */
+ if ((le16_to_cpu(rfd->command) & cb_el) &&
+ (RU_RUNNING == nic->ru_running))
+
+ if (ioread8(&nic->csr->scb.status) & rus_no_res)
+ nic->ru_running = RU_SUSPENDED;
+ pci_dma_sync_single_for_device(nic->pdev, rx->dma_addr,
+ sizeof(struct rfd),
+ PCI_DMA_FROMDEVICE);
+ return -ENODATA;
+ }
+
+ /* Get actual data size */
+ actual_size = le16_to_cpu(rfd->actual_size) & 0x3FFF;
+ if (unlikely(actual_size > RFD_BUF_LEN - sizeof(struct rfd)))
+ actual_size = RFD_BUF_LEN - sizeof(struct rfd);
+
+ /* Get data */
+ pci_unmap_single(nic->pdev, rx->dma_addr,
+ RFD_BUF_LEN, PCI_DMA_BIDIRECTIONAL);
+
+ /* If this buffer has the el bit, but we think the receiver
+ * is still running, check to see if it really stopped while
+ * we had interrupts off.
+ * This allows for a fast restart without re-enabling interrupts.
+ * This can happen when the RU sees the size change but also sees
+ * the el bit set. */
+ if ((le16_to_cpu(rfd->command) & cb_el) &&
+ (RU_RUNNING == nic->ru_running)) {
+
+ if (ioread8(&nic->csr->scb.status) & rus_no_res)
+ nic->ru_running = RU_SUSPENDED;
+ }
+
+ /* Pull off the RFD and put the actual data (minus eth hdr) */
+ skb_reserve(skb, sizeof(struct rfd));
+ skb_put(skb, actual_size);
+ skb->protocol = eth_type_trans(skb, nic->netdev);
+
+ if (unlikely(!(rfd_status & cb_ok))) {
+ /* Don't indicate if hardware indicates errors */
+ dev_kfree_skb_any(skb);
+ } else if (actual_size > ETH_DATA_LEN + VLAN_ETH_HLEN) {
+ /* Don't indicate oversized frames */
+ nic->rx_over_length_errors++;
+ dev_kfree_skb_any(skb);
+ } else {
+ dev->stats.rx_packets++;
+ dev->stats.rx_bytes += actual_size;
+ netif_receive_skb(skb);
+ if (work_done)
+ (*work_done)++;
+ }
+
+ rx->skb = NULL;
+
+ return 0;
+}
+
+static void e100_rx_clean(struct nic *nic, unsigned int *work_done,
+ unsigned int work_to_do)
+{
+ struct rx *rx;
+ int restart_required = 0, err = 0;
+ struct rx *old_before_last_rx, *new_before_last_rx;
+ struct rfd *old_before_last_rfd, *new_before_last_rfd;
+
+ /* Indicate newly arrived packets */
+ for (rx = nic->rx_to_clean; rx->skb; rx = nic->rx_to_clean = rx->next) {
+ err = e100_rx_indicate(nic, rx, work_done, work_to_do);
+ /* Hit quota or no more to clean */
+ if (-EAGAIN == err || -ENODATA == err)
+ break;
+ }
+
+
+ /* On EAGAIN, hit quota so have more work to do, restart once
+ * cleanup is complete.
+ * Else, are we already rnr? then pay attention!!! this ensures that
+ * the state machine progression never allows a start with a
+ * partially cleaned list, avoiding a race between hardware
+ * and rx_to_clean when in NAPI mode */
+ if (-EAGAIN != err && RU_SUSPENDED == nic->ru_running)
+ restart_required = 1;
+
+ old_before_last_rx = nic->rx_to_use->prev->prev;
+ old_before_last_rfd = (struct rfd *)old_before_last_rx->skb->data;
+
+ /* Alloc new skbs to refill list */
+ for (rx = nic->rx_to_use; !rx->skb; rx = nic->rx_to_use = rx->next) {
+ if (unlikely(e100_rx_alloc_skb(nic, rx)))
+ break; /* Better luck next time (see watchdog) */
+ }
+
+ new_before_last_rx = nic->rx_to_use->prev->prev;
+ if (new_before_last_rx != old_before_last_rx) {
+ /* Set the el-bit on the buffer that is before the last buffer.
+ * This lets us update the next pointer on the last buffer
+ * without worrying about hardware touching it.
+ * We set the size to 0 to prevent hardware from touching this
+ * buffer.
+ * When the hardware hits the before last buffer with el-bit
+ * and size of 0, it will RNR interrupt, the RUS will go into
+ * the No Resources state. It will not complete nor write to
+ * this buffer. */
+ new_before_last_rfd =
+ (struct rfd *)new_before_last_rx->skb->data;
+ new_before_last_rfd->size = 0;
+ new_before_last_rfd->command |= cpu_to_le16(cb_el);
+ pci_dma_sync_single_for_device(nic->pdev,
+ new_before_last_rx->dma_addr, sizeof(struct rfd),
+ PCI_DMA_BIDIRECTIONAL);
+
+ /* Now that we have a new stopping point, we can clear the old
+ * stopping point. We must sync twice to get the proper
+ * ordering on the hardware side of things. */
+ old_before_last_rfd->command &= ~cpu_to_le16(cb_el);
+ pci_dma_sync_single_for_device(nic->pdev,
+ old_before_last_rx->dma_addr, sizeof(struct rfd),
+ PCI_DMA_BIDIRECTIONAL);
+ old_before_last_rfd->size = cpu_to_le16(VLAN_ETH_FRAME_LEN);
+ pci_dma_sync_single_for_device(nic->pdev,
+ old_before_last_rx->dma_addr, sizeof(struct rfd),
+ PCI_DMA_BIDIRECTIONAL);
+ }
+
+ if (restart_required) {
+ // ack the rnr?
+ iowrite8(stat_ack_rnr, &nic->csr->scb.stat_ack);
+ e100_start_receiver(nic, nic->rx_to_clean);
+ if (work_done)
+ (*work_done)++;
+ }
+}
+
+static void e100_rx_clean_list(struct nic *nic)
+{
+ struct rx *rx;
+ unsigned int i, count = nic->params.rfds.count;
+
+ nic->ru_running = RU_UNINITIALIZED;
+
+ if (nic->rxs) {
+ for (rx = nic->rxs, i = 0; i < count; rx++, i++) {
+ if (rx->skb) {
+ pci_unmap_single(nic->pdev, rx->dma_addr,
+ RFD_BUF_LEN, PCI_DMA_BIDIRECTIONAL);
+ dev_kfree_skb(rx->skb);
+ }
+ }
+ kfree(nic->rxs);
+ nic->rxs = NULL;
+ }
+
+ nic->rx_to_use = nic->rx_to_clean = NULL;
+}
+
+static int e100_rx_alloc_list(struct nic *nic)
+{
+ struct rx *rx;
+ unsigned int i, count = nic->params.rfds.count;
+ struct rfd *before_last;
+
+ nic->rx_to_use = nic->rx_to_clean = NULL;
+ nic->ru_running = RU_UNINITIALIZED;
+
+ if (!(nic->rxs = kcalloc(count, sizeof(struct rx), GFP_ATOMIC)))
+ return -ENOMEM;
+
+ for (rx = nic->rxs, i = 0; i < count; rx++, i++) {
+ rx->next = (i + 1 < count) ? rx + 1 : nic->rxs;
+ rx->prev = (i == 0) ? nic->rxs + count - 1 : rx - 1;
+ if (e100_rx_alloc_skb(nic, rx)) {
+ e100_rx_clean_list(nic);
+ return -ENOMEM;
+ }
+ }
+ /* Set the el-bit on the buffer that is before the last buffer.
+ * This lets us update the next pointer on the last buffer without
+ * worrying about hardware touching it.
+ * We set the size to 0 to prevent hardware from touching this buffer.
+ * When the hardware hits the before last buffer with el-bit and size
+ * of 0, it will RNR interrupt, the RU will go into the No Resources
+ * state. It will not complete nor write to this buffer. */
+ rx = nic->rxs->prev->prev;
+ before_last = (struct rfd *)rx->skb->data;
+ before_last->command |= cpu_to_le16(cb_el);
+ before_last->size = 0;
+ pci_dma_sync_single_for_device(nic->pdev, rx->dma_addr,
+ sizeof(struct rfd), PCI_DMA_BIDIRECTIONAL);
+
+ nic->rx_to_use = nic->rx_to_clean = nic->rxs;
+ nic->ru_running = RU_SUSPENDED;
+
+ return 0;
+}
+
+static irqreturn_t e100_intr(int irq, void *dev_id)
+{
+ struct net_device *netdev = dev_id;
+ struct nic *nic = netdev_priv(netdev);
+ u8 stat_ack = ioread8(&nic->csr->scb.stat_ack);
+
+ netif_printk(nic, intr, KERN_DEBUG, nic->netdev,
+ "stat_ack = 0x%02X\n", stat_ack);
+
+ if (stat_ack == stat_ack_not_ours || /* Not our interrupt */
+ stat_ack == stat_ack_not_present) /* Hardware is ejected */
+ return IRQ_NONE;
+
+ /* Ack interrupt(s) */
+ iowrite8(stat_ack, &nic->csr->scb.stat_ack);
+
+ /* We hit Receive No Resource (RNR); restart RU after cleaning */
+ if (stat_ack & stat_ack_rnr)
+ nic->ru_running = RU_SUSPENDED;
+
+ if (likely(napi_schedule_prep(&nic->napi))) {
+ e100_disable_irq(nic);
+ __napi_schedule(&nic->napi);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int e100_poll(struct napi_struct *napi, int budget)
+{
+ struct nic *nic = container_of(napi, struct nic, napi);
+ unsigned int work_done = 0;
+
+ e100_rx_clean(nic, &work_done, budget);
+ e100_tx_clean(nic);
+
+ /* If budget not fully consumed, exit the polling mode */
+ if (work_done < budget) {
+ napi_complete(napi);
+ e100_enable_irq(nic);
+ }
+
+ return work_done;
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void e100_netpoll(struct net_device *netdev)
+{
+ struct nic *nic = netdev_priv(netdev);
+
+ e100_disable_irq(nic);
+ e100_intr(nic->pdev->irq, netdev);
+ e100_tx_clean(nic);
+ e100_enable_irq(nic);
+}
+#endif
+
+static int e100_set_mac_address(struct net_device *netdev, void *p)
+{
+ struct nic *nic = netdev_priv(netdev);
+ struct sockaddr *addr = p;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
+ e100_exec_cb(nic, NULL, e100_setup_iaaddr);
+
+ return 0;
+}
+
+static int e100_change_mtu(struct net_device *netdev, int new_mtu)
+{
+ if (new_mtu < ETH_ZLEN || new_mtu > ETH_DATA_LEN)
+ return -EINVAL;
+ netdev->mtu = new_mtu;
+ return 0;
+}
+
+static int e100_asf(struct nic *nic)
+{
+ /* ASF can be enabled from eeprom */
+ return((nic->pdev->device >= 0x1050) && (nic->pdev->device <= 0x1057) &&
+ (nic->eeprom[eeprom_config_asf] & eeprom_asf) &&
+ !(nic->eeprom[eeprom_config_asf] & eeprom_gcl) &&
+ ((nic->eeprom[eeprom_smbus_addr] & 0xFF) != 0xFE));
+}
+
+static int e100_up(struct nic *nic)
+{
+ int err;
+
+ if ((err = e100_rx_alloc_list(nic)))
+ return err;
+ if ((err = e100_alloc_cbs(nic)))
+ goto err_rx_clean_list;
+ if ((err = e100_hw_init(nic)))
+ goto err_clean_cbs;
+ e100_set_multicast_list(nic->netdev);
+ e100_start_receiver(nic, NULL);
+ mod_timer(&nic->watchdog, jiffies);
+ if ((err = request_irq(nic->pdev->irq, e100_intr, IRQF_SHARED,
+ nic->netdev->name, nic->netdev)))
+ goto err_no_irq;
+ netif_wake_queue(nic->netdev);
+ napi_enable(&nic->napi);
+ /* enable ints _after_ enabling poll, preventing a race between
+ * disable ints+schedule */
+ e100_enable_irq(nic);
+ return 0;
+
+err_no_irq:
+ del_timer_sync(&nic->watchdog);
+err_clean_cbs:
+ e100_clean_cbs(nic);
+err_rx_clean_list:
+ e100_rx_clean_list(nic);
+ return err;
+}
+
+static void e100_down(struct nic *nic)
+{
+ /* wait here for poll to complete */
+ napi_disable(&nic->napi);
+ netif_stop_queue(nic->netdev);
+ e100_hw_reset(nic);
+ free_irq(nic->pdev->irq, nic->netdev);
+ del_timer_sync(&nic->watchdog);
+ netif_carrier_off(nic->netdev);
+ e100_clean_cbs(nic);
+ e100_rx_clean_list(nic);
+}
+
+static void e100_tx_timeout(struct net_device *netdev)
+{
+ struct nic *nic = netdev_priv(netdev);
+
+ /* Reset outside of interrupt context, to avoid request_irq
+ * in interrupt context */
+ schedule_work(&nic->tx_timeout_task);
+}
+
+static void e100_tx_timeout_task(struct work_struct *work)
+{
+ struct nic *nic = container_of(work, struct nic, tx_timeout_task);
+ struct net_device *netdev = nic->netdev;
+
+ netif_printk(nic, tx_err, KERN_DEBUG, nic->netdev,
+ "scb.status=0x%02X\n", ioread8(&nic->csr->scb.status));
+
+ rtnl_lock();
+ if (netif_running(netdev)) {
+ e100_down(netdev_priv(netdev));
+ e100_up(netdev_priv(netdev));
+ }
+ rtnl_unlock();
+}
+
+static int e100_loopback_test(struct nic *nic, enum loopback loopback_mode)
+{
+ int err;
+ struct sk_buff *skb;
+
+ /* Use driver resources to perform internal MAC or PHY
+ * loopback test. A single packet is prepared and transmitted
+ * in loopback mode, and the test passes if the received
+ * packet compares byte-for-byte to the transmitted packet. */
+
+ if ((err = e100_rx_alloc_list(nic)))
+ return err;
+ if ((err = e100_alloc_cbs(nic)))
+ goto err_clean_rx;
+
+ /* ICH PHY loopback is broken so do MAC loopback instead */
+ if (nic->flags & ich && loopback_mode == lb_phy)
+ loopback_mode = lb_mac;
+
+ nic->loopback = loopback_mode;
+ if ((err = e100_hw_init(nic)))
+ goto err_loopback_none;
+
+ if (loopback_mode == lb_phy)
+ mdio_write(nic->netdev, nic->mii.phy_id, MII_BMCR,
+ BMCR_LOOPBACK);
+
+ e100_start_receiver(nic, NULL);
+
+ if (!(skb = netdev_alloc_skb(nic->netdev, ETH_DATA_LEN))) {
+ err = -ENOMEM;
+ goto err_loopback_none;
+ }
+ skb_put(skb, ETH_DATA_LEN);
+ memset(skb->data, 0xFF, ETH_DATA_LEN);
+ e100_xmit_frame(skb, nic->netdev);
+
+ msleep(10);
+
+ pci_dma_sync_single_for_cpu(nic->pdev, nic->rx_to_clean->dma_addr,
+ RFD_BUF_LEN, PCI_DMA_BIDIRECTIONAL);
+
+ if (memcmp(nic->rx_to_clean->skb->data + sizeof(struct rfd),
+ skb->data, ETH_DATA_LEN))
+ err = -EAGAIN;
+
+err_loopback_none:
+ mdio_write(nic->netdev, nic->mii.phy_id, MII_BMCR, 0);
+ nic->loopback = lb_none;
+ e100_clean_cbs(nic);
+ e100_hw_reset(nic);
+err_clean_rx:
+ e100_rx_clean_list(nic);
+ return err;
+}
+
+#define MII_LED_CONTROL 0x1B
+#define E100_82552_LED_OVERRIDE 0x19
+#define E100_82552_LED_ON 0x000F /* LEDTX and LED_RX both on */
+#define E100_82552_LED_OFF 0x000A /* LEDTX and LED_RX both off */
+static void e100_blink_led(unsigned long data)
+{
+ struct nic *nic = (struct nic *)data;
+ enum led_state {
+ led_on = 0x01,
+ led_off = 0x04,
+ led_on_559 = 0x05,
+ led_on_557 = 0x07,
+ };
+ u16 led_reg = MII_LED_CONTROL;
+
+ if (nic->phy == phy_82552_v) {
+ led_reg = E100_82552_LED_OVERRIDE;
+
+ nic->leds = (nic->leds == E100_82552_LED_ON) ?
+ E100_82552_LED_OFF : E100_82552_LED_ON;
+ } else {
+ nic->leds = (nic->leds & led_on) ? led_off :
+ (nic->mac < mac_82559_D101M) ? led_on_557 :
+ led_on_559;
+ }
+ mdio_write(nic->netdev, nic->mii.phy_id, led_reg, nic->leds);
+ mod_timer(&nic->blink_timer, jiffies + HZ / 4);
+}
+
+static int e100_get_settings(struct net_device *netdev, struct ethtool_cmd *cmd)
+{
+ struct nic *nic = netdev_priv(netdev);
+ return mii_ethtool_gset(&nic->mii, cmd);
+}
+
+static int e100_set_settings(struct net_device *netdev, struct ethtool_cmd *cmd)
+{
+ struct nic *nic = netdev_priv(netdev);
+ int err;
+
+ mdio_write(netdev, nic->mii.phy_id, MII_BMCR, BMCR_RESET);
+ err = mii_ethtool_sset(&nic->mii, cmd);
+ e100_exec_cb(nic, NULL, e100_configure);
+
+ return err;
+}
+
+static void e100_get_drvinfo(struct net_device *netdev,
+ struct ethtool_drvinfo *info)
+{
+ struct nic *nic = netdev_priv(netdev);
+ strcpy(info->driver, DRV_NAME);
+ strcpy(info->version, DRV_VERSION);
+ strcpy(info->fw_version, "N/A");
+ strcpy(info->bus_info, pci_name(nic->pdev));
+}
+
+#define E100_PHY_REGS 0x1C
+static int e100_get_regs_len(struct net_device *netdev)
+{
+ struct nic *nic = netdev_priv(netdev);
+ return 1 + E100_PHY_REGS + sizeof(nic->mem->dump_buf);
+}
+
+static void e100_get_regs(struct net_device *netdev,
+ struct ethtool_regs *regs, void *p)
+{
+ struct nic *nic = netdev_priv(netdev);
+ u32 *buff = p;
+ int i;
+
+ regs->version = (1 << 24) | nic->pdev->revision;
+ buff[0] = ioread8(&nic->csr->scb.cmd_hi) << 24 |
+ ioread8(&nic->csr->scb.cmd_lo) << 16 |
+ ioread16(&nic->csr->scb.status);
+ for (i = E100_PHY_REGS; i >= 0; i--)
+ buff[1 + E100_PHY_REGS - i] =
+ mdio_read(netdev, nic->mii.phy_id, i);
+ memset(nic->mem->dump_buf, 0, sizeof(nic->mem->dump_buf));
+ e100_exec_cb(nic, NULL, e100_dump);
+ msleep(10);
+ memcpy(&buff[2 + E100_PHY_REGS], nic->mem->dump_buf,
+ sizeof(nic->mem->dump_buf));
+}
+
+static void e100_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
+{
+ struct nic *nic = netdev_priv(netdev);
+ wol->supported = (nic->mac >= mac_82558_D101_A4) ? WAKE_MAGIC : 0;
+ wol->wolopts = (nic->flags & wol_magic) ? WAKE_MAGIC : 0;
+}
+
+static int e100_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
+{
+ struct nic *nic = netdev_priv(netdev);
+
+ if ((wol->wolopts && wol->wolopts != WAKE_MAGIC) ||
+ !device_can_wakeup(&nic->pdev->dev))
+ return -EOPNOTSUPP;
+
+ if (wol->wolopts)
+ nic->flags |= wol_magic;
+ else
+ nic->flags &= ~wol_magic;
+
+ device_set_wakeup_enable(&nic->pdev->dev, wol->wolopts);
+
+ e100_exec_cb(nic, NULL, e100_configure);
+
+ return 0;
+}
+
+static u32 e100_get_msglevel(struct net_device *netdev)
+{
+ struct nic *nic = netdev_priv(netdev);
+ return nic->msg_enable;
+}
+
+static void e100_set_msglevel(struct net_device *netdev, u32 value)
+{
+ struct nic *nic = netdev_priv(netdev);
+ nic->msg_enable = value;
+}
+
+static int e100_nway_reset(struct net_device *netdev)
+{
+ struct nic *nic = netdev_priv(netdev);
+ return mii_nway_restart(&nic->mii);
+}
+
+static u32 e100_get_link(struct net_device *netdev)
+{
+ struct nic *nic = netdev_priv(netdev);
+ return mii_link_ok(&nic->mii);
+}
+
+static int e100_get_eeprom_len(struct net_device *netdev)
+{
+ struct nic *nic = netdev_priv(netdev);
+ return nic->eeprom_wc << 1;
+}
+
+#define E100_EEPROM_MAGIC 0x1234
+static int e100_get_eeprom(struct net_device *netdev,
+ struct ethtool_eeprom *eeprom, u8 *bytes)
+{
+ struct nic *nic = netdev_priv(netdev);
+
+ eeprom->magic = E100_EEPROM_MAGIC;
+ memcpy(bytes, &((u8 *)nic->eeprom)[eeprom->offset], eeprom->len);
+
+ return 0;
+}
+
+static int e100_set_eeprom(struct net_device *netdev,
+ struct ethtool_eeprom *eeprom, u8 *bytes)
+{
+ struct nic *nic = netdev_priv(netdev);
+
+ if (eeprom->magic != E100_EEPROM_MAGIC)
+ return -EINVAL;
+
+ memcpy(&((u8 *)nic->eeprom)[eeprom->offset], bytes, eeprom->len);
+
+ return e100_eeprom_save(nic, eeprom->offset >> 1,
+ (eeprom->len >> 1) + 1);
+}
+
+static void e100_get_ringparam(struct net_device *netdev,
+ struct ethtool_ringparam *ring)
+{
+ struct nic *nic = netdev_priv(netdev);
+ struct param_range *rfds = &nic->params.rfds;
+ struct param_range *cbs = &nic->params.cbs;
+
+ ring->rx_max_pending = rfds->max;
+ ring->tx_max_pending = cbs->max;
+ ring->rx_mini_max_pending = 0;
+ ring->rx_jumbo_max_pending = 0;
+ ring->rx_pending = rfds->count;
+ ring->tx_pending = cbs->count;
+ ring->rx_mini_pending = 0;
+ ring->rx_jumbo_pending = 0;
+}
+
+static int e100_set_ringparam(struct net_device *netdev,
+ struct ethtool_ringparam *ring)
+{
+ struct nic *nic = netdev_priv(netdev);
+ struct param_range *rfds = &nic->params.rfds;
+ struct param_range *cbs = &nic->params.cbs;
+
+ if ((ring->rx_mini_pending) || (ring->rx_jumbo_pending))
+ return -EINVAL;
+
+ if (netif_running(netdev))
+ e100_down(nic);
+ rfds->count = max(ring->rx_pending, rfds->min);
+ rfds->count = min(rfds->count, rfds->max);
+ cbs->count = max(ring->tx_pending, cbs->min);
+ cbs->count = min(cbs->count, cbs->max);
+ netif_info(nic, drv, nic->netdev, "Ring Param settings: rx: %d, tx %d\n",
+ rfds->count, cbs->count);
+ if (netif_running(netdev))
+ e100_up(nic);
+
+ return 0;
+}
+
+static const char e100_gstrings_test[][ETH_GSTRING_LEN] = {
+ "Link test (on/offline)",
+ "Eeprom test (on/offline)",
+ "Self test (offline)",
+ "Mac loopback (offline)",
+ "Phy loopback (offline)",
+};
+#define E100_TEST_LEN ARRAY_SIZE(e100_gstrings_test)
+
+static void e100_diag_test(struct net_device *netdev,
+ struct ethtool_test *test, u64 *data)
+{
+ struct ethtool_cmd cmd;
+ struct nic *nic = netdev_priv(netdev);
+ int i, err;
+
+ memset(data, 0, E100_TEST_LEN * sizeof(u64));
+ data[0] = !mii_link_ok(&nic->mii);
+ data[1] = e100_eeprom_load(nic);
+ if (test->flags & ETH_TEST_FL_OFFLINE) {
+
+ /* save speed, duplex & autoneg settings */
+ err = mii_ethtool_gset(&nic->mii, &cmd);
+
+ if (netif_running(netdev))
+ e100_down(nic);
+ data[2] = e100_self_test(nic);
+ data[3] = e100_loopback_test(nic, lb_mac);
+ data[4] = e100_loopback_test(nic, lb_phy);
+
+ /* restore speed, duplex & autoneg settings */
+ err = mii_ethtool_sset(&nic->mii, &cmd);
+
+ if (netif_running(netdev))
+ e100_up(nic);
+ }
+ for (i = 0; i < E100_TEST_LEN; i++)
+ test->flags |= data[i] ? ETH_TEST_FL_FAILED : 0;
+
+ msleep_interruptible(4 * 1000);
+}
+
+static int e100_phys_id(struct net_device *netdev, u32 data)
+{
+ struct nic *nic = netdev_priv(netdev);
+ u16 led_reg = (nic->phy == phy_82552_v) ? E100_82552_LED_OVERRIDE :
+ MII_LED_CONTROL;
+
+ if (!data || data > (u32)(MAX_SCHEDULE_TIMEOUT / HZ))
+ data = (u32)(MAX_SCHEDULE_TIMEOUT / HZ);
+ mod_timer(&nic->blink_timer, jiffies);
+ msleep_interruptible(data * 1000);
+ del_timer_sync(&nic->blink_timer);
+ mdio_write(netdev, nic->mii.phy_id, led_reg, 0);
+
+ return 0;
+}
+
+static const char e100_gstrings_stats[][ETH_GSTRING_LEN] = {
+ "rx_packets", "tx_packets", "rx_bytes", "tx_bytes", "rx_errors",
+ "tx_errors", "rx_dropped", "tx_dropped", "multicast", "collisions",
+ "rx_length_errors", "rx_over_errors", "rx_crc_errors",
+ "rx_frame_errors", "rx_fifo_errors", "rx_missed_errors",
+ "tx_aborted_errors", "tx_carrier_errors", "tx_fifo_errors",
+ "tx_heartbeat_errors", "tx_window_errors",
+ /* device-specific stats */
+ "tx_deferred", "tx_single_collisions", "tx_multi_collisions",
+ "tx_flow_control_pause", "rx_flow_control_pause",
+ "rx_flow_control_unsupported", "tx_tco_packets", "rx_tco_packets",
+};
+#define E100_NET_STATS_LEN 21
+#define E100_STATS_LEN ARRAY_SIZE(e100_gstrings_stats)
+
+static int e100_get_sset_count(struct net_device *netdev, int sset)
+{
+ switch (sset) {
+ case ETH_SS_TEST:
+ return E100_TEST_LEN;
+ case ETH_SS_STATS:
+ return E100_STATS_LEN;
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static void e100_get_ethtool_stats(struct net_device *netdev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct nic *nic = netdev_priv(netdev);
+ int i;
+
+ for (i = 0; i < E100_NET_STATS_LEN; i++)
+ data[i] = ((unsigned long *)&netdev->stats)[i];
+
+ data[i++] = nic->tx_deferred;
+ data[i++] = nic->tx_single_collisions;
+ data[i++] = nic->tx_multiple_collisions;
+ data[i++] = nic->tx_fc_pause;
+ data[i++] = nic->rx_fc_pause;
+ data[i++] = nic->rx_fc_unsupported;
+ data[i++] = nic->tx_tco_frames;
+ data[i++] = nic->rx_tco_frames;
+}
+
+static void e100_get_strings(struct net_device *netdev, u32 stringset, u8 *data)
+{
+ switch (stringset) {
+ case ETH_SS_TEST:
+ memcpy(data, *e100_gstrings_test, sizeof(e100_gstrings_test));
+ break;
+ case ETH_SS_STATS:
+ memcpy(data, *e100_gstrings_stats, sizeof(e100_gstrings_stats));
+ break;
+ }
+}
+
+static const struct ethtool_ops e100_ethtool_ops = {
+ .get_settings = e100_get_settings,
+ .set_settings = e100_set_settings,
+ .get_drvinfo = e100_get_drvinfo,
+ .get_regs_len = e100_get_regs_len,
+ .get_regs = e100_get_regs,
+ .get_wol = e100_get_wol,
+ .set_wol = e100_set_wol,
+ .get_msglevel = e100_get_msglevel,
+ .set_msglevel = e100_set_msglevel,
+ .nway_reset = e100_nway_reset,
+ .get_link = e100_get_link,
+ .get_eeprom_len = e100_get_eeprom_len,
+ .get_eeprom = e100_get_eeprom,
+ .set_eeprom = e100_set_eeprom,
+ .get_ringparam = e100_get_ringparam,
+ .set_ringparam = e100_set_ringparam,
+ .self_test = e100_diag_test,
+ .get_strings = e100_get_strings,
+ .phys_id = e100_phys_id,
+ .get_ethtool_stats = e100_get_ethtool_stats,
+ .get_sset_count = e100_get_sset_count,
+};
+
+static int e100_do_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
+{
+ struct nic *nic = netdev_priv(netdev);
+
+ return generic_mii_ioctl(&nic->mii, if_mii(ifr), cmd, NULL);
+}
+
+static int e100_alloc(struct nic *nic)
+{
+ nic->mem = pci_alloc_consistent(nic->pdev, sizeof(struct mem),
+ &nic->dma_addr);
+ return nic->mem ? 0 : -ENOMEM;
+}
+
+static void e100_free(struct nic *nic)
+{
+ if (nic->mem) {
+ pci_free_consistent(nic->pdev, sizeof(struct mem),
+ nic->mem, nic->dma_addr);
+ nic->mem = NULL;
+ }
+}
+
+static int e100_open(struct net_device *netdev)
+{
+ struct nic *nic = netdev_priv(netdev);
+ int err = 0;
+
+ netif_carrier_off(netdev);
+ if ((err = e100_up(nic)))
+ netif_err(nic, ifup, nic->netdev, "Cannot open interface, aborting\n");
+ return err;
+}
+
+static int e100_close(struct net_device *netdev)
+{
+ e100_down(netdev_priv(netdev));
+ return 0;
+}
+
+static const struct net_device_ops e100_netdev_ops = {
+ .ndo_open = e100_open,
+ .ndo_stop = e100_close,
+ .ndo_start_xmit = e100_xmit_frame,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_multicast_list = e100_set_multicast_list,
+ .ndo_set_mac_address = e100_set_mac_address,
+ .ndo_change_mtu = e100_change_mtu,
+ .ndo_do_ioctl = e100_do_ioctl,
+ .ndo_tx_timeout = e100_tx_timeout,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = e100_netpoll,
+#endif
+};
+
+static int __devinit e100_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct net_device *netdev;
+ struct nic *nic;
+ int err;
+
+ if (!(netdev = alloc_etherdev(sizeof(struct nic)))) {
+ if (((1 << debug) - 1) & NETIF_MSG_PROBE)
+ pr_err("Etherdev alloc failed, aborting\n");
+ return -ENOMEM;
+ }
+
+ netdev->netdev_ops = &e100_netdev_ops;
+ SET_ETHTOOL_OPS(netdev, &e100_ethtool_ops);
+ netdev->watchdog_timeo = E100_WATCHDOG_PERIOD;
+ strncpy(netdev->name, pci_name(pdev), sizeof(netdev->name) - 1);
+
+ nic = netdev_priv(netdev);
+ netif_napi_add(netdev, &nic->napi, e100_poll, E100_NAPI_WEIGHT);
+ nic->netdev = netdev;
+ nic->pdev = pdev;
+ nic->msg_enable = (1 << debug) - 1;
+ nic->mdio_ctrl = mdio_ctrl_hw;
+ pci_set_drvdata(pdev, netdev);
+
+ if ((err = pci_enable_device(pdev))) {
+ netif_err(nic, probe, nic->netdev, "Cannot enable PCI device, aborting\n");
+ goto err_out_free_dev;
+ }
+
+ if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) {
+ netif_err(nic, probe, nic->netdev, "Cannot find proper PCI device base address, aborting\n");
+ err = -ENODEV;
+ goto err_out_disable_pdev;
+ }
+
+ if ((err = pci_request_regions(pdev, DRV_NAME))) {
+ netif_err(nic, probe, nic->netdev, "Cannot obtain PCI resources, aborting\n");
+ goto err_out_disable_pdev;
+ }
+
+ if ((err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)))) {
+ netif_err(nic, probe, nic->netdev, "No usable DMA configuration, aborting\n");
+ goto err_out_free_res;
+ }
+
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+
+ if (use_io)
+ netif_info(nic, probe, nic->netdev, "using i/o access mode\n");
+
+ nic->csr = pci_iomap(pdev, (use_io ? 1 : 0), sizeof(struct csr));
+ if (!nic->csr) {
+ netif_err(nic, probe, nic->netdev, "Cannot map device registers, aborting\n");
+ err = -ENOMEM;
+ goto err_out_free_res;
+ }
+
+ if (ent->driver_data)
+ nic->flags |= ich;
+ else
+ nic->flags &= ~ich;
+
+ e100_get_defaults(nic);
+
+ /* locks must be initialized before calling hw_reset */
+ spin_lock_init(&nic->cb_lock);
+ spin_lock_init(&nic->cmd_lock);
+ spin_lock_init(&nic->mdio_lock);
+
+ /* Reset the device before pci_set_master() in case device is in some
+ * funky state and has an interrupt pending - hint: we don't have the
+ * interrupt handler registered yet. */
+ e100_hw_reset(nic);
+
+ pci_set_master(pdev);
+
+ init_timer(&nic->watchdog);
+ nic->watchdog.function = e100_watchdog;
+ nic->watchdog.data = (unsigned long)nic;
+ init_timer(&nic->blink_timer);
+ nic->blink_timer.function = e100_blink_led;
+ nic->blink_timer.data = (unsigned long)nic;
+
+ INIT_WORK(&nic->tx_timeout_task, e100_tx_timeout_task);
+
+ if ((err = e100_alloc(nic))) {
+ netif_err(nic, probe, nic->netdev, "Cannot alloc driver memory, aborting\n");
+ goto err_out_iounmap;
+ }
+
+ if ((err = e100_eeprom_load(nic)))
+ goto err_out_free;
+
+ e100_phy_init(nic);
+
+ memcpy(netdev->dev_addr, nic->eeprom, ETH_ALEN);
+ memcpy(netdev->perm_addr, nic->eeprom, ETH_ALEN);
+ if (!is_valid_ether_addr(netdev->perm_addr)) {
+ if (!eeprom_bad_csum_allow) {
+ netif_err(nic, probe, nic->netdev, "Invalid MAC address from EEPROM, aborting\n");
+ err = -EAGAIN;
+ goto err_out_free;
+ } else {
+ netif_err(nic, probe, nic->netdev, "Invalid MAC address from EEPROM, you MUST configure one.\n");
+ }
+ }
+
+ /* Wol magic packet can be enabled from eeprom */
+ if ((nic->mac >= mac_82558_D101_A4) &&
+ (nic->eeprom[eeprom_id] & eeprom_id_wol)) {
+ nic->flags |= wol_magic;
+ device_set_wakeup_enable(&pdev->dev, true);
+ }
+
+ /* ack any pending wake events, disable PME */
+ pci_pme_active(pdev, false);
+
+ strcpy(netdev->name, "eth%d");
+ if ((err = register_netdev(netdev))) {
+ netif_err(nic, probe, nic->netdev, "Cannot register net device, aborting\n");
+ goto err_out_free;
+ }
+ nic->cbs_pool = pci_pool_create(netdev->name,
+ nic->pdev,
+ nic->params.cbs.max * sizeof(struct cb),
+ sizeof(u32),
+ 0);
+ netif_info(nic, probe, nic->netdev,
+ "addr 0x%llx, irq %d, MAC addr %pM\n",
+ (unsigned long long)pci_resource_start(pdev, use_io ? 1 : 0),
+ pdev->irq, netdev->dev_addr);
+
+ return 0;
+
+err_out_free:
+ e100_free(nic);
+err_out_iounmap:
+ pci_iounmap(pdev, nic->csr);
+err_out_free_res:
+ pci_release_regions(pdev);
+err_out_disable_pdev:
+ pci_disable_device(pdev);
+err_out_free_dev:
+ pci_set_drvdata(pdev, NULL);
+ free_netdev(netdev);
+ return err;
+}
+
+static void __devexit e100_remove(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+
+ if (netdev) {
+ struct nic *nic = netdev_priv(netdev);
+ unregister_netdev(netdev);
+ e100_free(nic);
+ pci_iounmap(pdev, nic->csr);
+ pci_pool_destroy(nic->cbs_pool);
+ free_netdev(netdev);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+ pci_set_drvdata(pdev, NULL);
+ }
+}
+
+#define E100_82552_SMARTSPEED 0x14 /* SmartSpeed Ctrl register */
+#define E100_82552_REV_ANEG 0x0200 /* Reverse auto-negotiation */
+#define E100_82552_ANEG_NOW 0x0400 /* Auto-negotiate now */
+static void __e100_shutdown(struct pci_dev *pdev, bool *enable_wake)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct nic *nic = netdev_priv(netdev);
+
+ if (netif_running(netdev))
+ e100_down(nic);
+ netif_device_detach(netdev);
+
+ pci_save_state(pdev);
+
+ if ((nic->flags & wol_magic) | e100_asf(nic)) {
+ /* enable reverse auto-negotiation */
+ if (nic->phy == phy_82552_v) {
+ u16 smartspeed = mdio_read(netdev, nic->mii.phy_id,
+ E100_82552_SMARTSPEED);
+
+ mdio_write(netdev, nic->mii.phy_id,
+ E100_82552_SMARTSPEED, smartspeed |
+ E100_82552_REV_ANEG | E100_82552_ANEG_NOW);
+ }
+ *enable_wake = true;
+ } else {
+ *enable_wake = false;
+ }
+
+ pci_disable_device(pdev);
+}
+
+static int __e100_power_off(struct pci_dev *pdev, bool wake)
+{
+ if (wake)
+ return pci_prepare_to_sleep(pdev);
+
+ pci_wake_from_d3(pdev, false);
+ pci_set_power_state(pdev, PCI_D3hot);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int e100_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ bool wake;
+ __e100_shutdown(pdev, &wake);
+ return __e100_power_off(pdev, wake);
+}
+
+static int e100_resume(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct nic *nic = netdev_priv(netdev);
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+ /* ack any pending wake events, disable PME */
+ pci_enable_wake(pdev, 0, 0);
+
+ /* disable reverse auto-negotiation */
+ if (nic->phy == phy_82552_v) {
+ u16 smartspeed = mdio_read(netdev, nic->mii.phy_id,
+ E100_82552_SMARTSPEED);
+
+ mdio_write(netdev, nic->mii.phy_id,
+ E100_82552_SMARTSPEED,
+ smartspeed & ~(E100_82552_REV_ANEG));
+ }
+
+ netif_device_attach(netdev);
+ if (netif_running(netdev))
+ e100_up(nic);
+
+ return 0;
+}
+#endif /* CONFIG_PM */
+
+static void e100_shutdown(struct pci_dev *pdev)
+{
+ bool wake;
+ __e100_shutdown(pdev, &wake);
+ if (system_state == SYSTEM_POWER_OFF)
+ __e100_power_off(pdev, wake);
+}
+
+/* ------------------ PCI Error Recovery infrastructure -------------- */
+/**
+ * e100_io_error_detected - called when PCI error is detected.
+ * @pdev: Pointer to PCI device
+ * @state: The current pci connection state
+ */
+static pci_ers_result_t e100_io_error_detected(struct pci_dev *pdev, pci_channel_state_t state)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct nic *nic = netdev_priv(netdev);
+
+ netif_device_detach(netdev);
+
+ if (state == pci_channel_io_perm_failure)
+ return PCI_ERS_RESULT_DISCONNECT;
+
+ if (netif_running(netdev))
+ e100_down(nic);
+ pci_disable_device(pdev);
+
+ /* Request a slot reset. */
+ return PCI_ERS_RESULT_NEED_RESET;
+}
+
+/**
+ * e100_io_slot_reset - called after the pci bus has been reset.
+ * @pdev: Pointer to PCI device
+ *
+ * Restart the card from scratch.
+ */
+static pci_ers_result_t e100_io_slot_reset(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct nic *nic = netdev_priv(netdev);
+
+ if (pci_enable_device(pdev)) {
+ pr_err("Cannot re-enable PCI device after reset\n");
+ return PCI_ERS_RESULT_DISCONNECT;
+ }
+ pci_set_master(pdev);
+
+ /* Only one device per card can do a reset */
+ if (0 != PCI_FUNC(pdev->devfn))
+ return PCI_ERS_RESULT_RECOVERED;
+ e100_hw_reset(nic);
+ e100_phy_init(nic);
+
+ return PCI_ERS_RESULT_RECOVERED;
+}
+
+/**
+ * e100_io_resume - resume normal operations
+ * @pdev: Pointer to PCI device
+ *
+ * Resume normal operations after an error recovery
+ * sequence has been completed.
+ */
+static void e100_io_resume(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct nic *nic = netdev_priv(netdev);
+
+ /* ack any pending wake events, disable PME */
+ pci_enable_wake(pdev, 0, 0);
+
+ netif_device_attach(netdev);
+ if (netif_running(netdev)) {
+ e100_open(netdev);
+ mod_timer(&nic->watchdog, jiffies);
+ }
+}
+
+static struct pci_error_handlers e100_err_handler = {
+ .error_detected = e100_io_error_detected,
+ .slot_reset = e100_io_slot_reset,
+ .resume = e100_io_resume,
+};
+
+static struct pci_driver e100_driver = {
+ .name = DRV_NAME,
+ .id_table = e100_id_table,
+ .probe = e100_probe,
+ .remove = __devexit_p(e100_remove),
+#ifdef CONFIG_PM
+ /* Power Management hooks */
+ .suspend = e100_suspend,
+ .resume = e100_resume,
+#endif
+ .shutdown = e100_shutdown,
+ .err_handler = &e100_err_handler,
+};
+
+static int __init e100_init_module(void)
+{
+ if (((1 << debug) - 1) & NETIF_MSG_DRV) {
+ pr_info("%s, %s\n", DRV_DESCRIPTION, DRV_VERSION);
+ pr_info("%s\n", DRV_COPYRIGHT);
+ }
+ return pci_register_driver(&e100_driver);
+}
+
+static void __exit e100_cleanup_module(void)
+{
+ pci_unregister_driver(&e100_driver);
+}
+
+module_init(e100_init_module);
+module_exit(e100_cleanup_module);