MQTT: (WIP) Fix OpenSSL linking.
Standard library
================
..
Documentation originally part of Smarteh's user Manual, and donated to Beremiz project.
.. list-table::
* - .. figure:: library_panel.png
Library browser
- Library contains various groups of standard
and user defined functions. They support the
usage in different programmable controller
programming languages inside POUs.
* - .. figure:: block_properties.png
Block Properties
- Block Properties pop-up window can be
opened by double-click on function block.
Some of the blocks can have more inputs than
default. This is selectable in the Inputs field
(e.g. ADD block). Also an Execution Order of
the blocks can be programmer-defined. All
blocks have an additional Execution Control
check-box. If it is checked than two new pins
are added (EN – input and ENO – output) to
control dynamically their execution.
Standard function blocks
------------------------
.. highlight:: text
.. list-table::
* - .. figure:: std_block-012.png
SR bistable
- The SR bistable is a latch where the Set dominates.::
( BOOL:S1, BOOL:R ) => ( BOOL:Q1 )
This function represents a standard set-dominant set/reset flip
flop. The Q1 output become TRUE when the input S1 is TRUE and
the R input is FALSE. In the same way, the Q1 output become
FALSE when the input S1 is FALSE and the R input is TRUE. After
one of these transitions, when both the S1 and R signals return to
FALSE, the Q1 output keeps the previous state until a new
condition occurs. If you apply a TRUE condition for both the
signals, the Q1 output is forced to TRUE (set-dominant).
* - .. figure:: std_block-010.png
RS bistable
- The RS bistable is a latch where the Reset dominates.::
( BOOL:S, BOOL:R1 ) => ( BOOL:Q1 )
This function represents a standard reset-dominant set/reset flip
flop. The Q1 output become TRUE when the input S is TRUE and
the R1 input is FALSE. In the same way, the Q1 output become
FALSE when the input S is FALSE and the R1 input is TRUE. After
one of these transitions, when both the S and R1 signals return to
FALSE, the Q1 output keeps the previous state until a new
condition occurs. If you apply a TRUE condition for both the
signals, the Q1 output is forced to FALSE (reset-dominant).
* - .. figure:: std_block-019.png
SEMA Semaphore
- The semaphore provides a mechanism to allow software elements
mutually exclusive access to certain resources.::
( BOOL:CLAIM, BOOL:RELEASE ) => ( BOOL:BUSY )
This function block implements a semaphore function. Normally
this function is used to synchronize events. The BUSY output is
activated by a TRUE condition on the CLAIM input and it is de-
activated by a TRUE condition on the RELEASE input.
* - .. figure:: std_block-021.png
R_TRIG Rising edge detector
- The output produces a single pulse when a rising edge is detected.::
( BOOL:CLK ) => ( BOOL:Q )
This function is a rising-edge detector. The Q output becomes
TRUE when a 0 to 1 (or FALSE to TRUE or OFF to ON) condition is
detected on the CLK input and it sustains this state for a complete
scan cycle.
* - .. figure:: std_block-023.png
F TRIG
- Falling edge detector
The output Q produces a single pulse when a falling edge is
detected.::
( BOOL:CLK ) => ( BOOL:Q )
This function is a falling-edge detector. The Q output becomes
TRUE when a 1 to 0 (or TRUE to FALSE or ON to OFF) condition is
detected on the CLK input and it sustains this state for a complete
scan cycle.
* - .. figure:: std_block-030.png
CTU
CTU_DINT,
CTU_LINT,
CTU_UDINT, CTU_ULINT
Up-counter
- The up-counter can be used to signal when a count has reached a
maximum value.::
CTU: ( BOOL:CU, BOOL:R, INT:PV ) => ( BOOL:Q, INT:CV )
CTU_DINT: ( BOOL:CU, BOOL:R, DINT:PV ) => ( BOOL:Q, DINT:CV )
CTU_LINT:
( BOOL:CU, BOOL:R, LINT:PV ) => ( BOOL:Q, LINT:CV )
CTU_UDINT: ( BOOL:CU, BOOL:R, UDINT:PV ) => ( BOOL:Q, UDINT:CV )
CTU_ULINT: ( BOOL:CU, BOOL:R, ULINT:PV ) => ( BOOL:Q, ULINT:CV )
The CTU function represents an up-counter. A rising-edge on CU
input will increment the counter by one. When the programmed
value, applied to the input PV, is reached, the Q output becomes
TRUE. Applying a TRUE signal on R input will reset the counter to
zero (Asynchronous reset). The CV output reports the current
counting value.
* - .. figure:: std_block-028.png
CTD
CTD_DINT, CTD_LINT,
CTD_UDINT, CTD_ULINT
Down-counter
- The down-counter can be used to signal when a count has reached
zero, on counting down from a pre-set value.::
CTD: ( BOOL:CD, BOOL:LD, INT:PV ) => ( BOOL:Q, INT:CV )
CTD_DINT: ( BOOL:CD, BOOL:LD, DINT:PV ) => ( BOOL:Q, DINT:CV )
CTD_LINT: ( BOOL:CD, BOOL:LD, LINT:PV ) => ( BOOL:Q, LINT:CV )
CTD_UDINT: ( BOOL:CD, BOOL:LD, UDINT:PV ) => ( BOOL:Q, UDINT:CV )
CTD_ULINT: ( BOOL:CD, BOOL:LD, ULINT:PV ) => ( BOOL:Q, ULINT:CV )
The CTD function represents a down-counter. A rising-edge on CD
input will decrement the counter by one. The Q output becomes
TRUE when the current counting value is equal or less than zero.
Applying a TRUE signal on LD (LOAD) input will load the counter
with the value present at input PV (Asynchronous load). The CV
output reports the current counting value.
* - .. figure:: std_block-035.png
CTUD
CTUD_DINT,
CTUD_LINT,
CTUD_UDINT,
CTUD_ULINT
Up-down counter
- The up-down counter has two inputs CU and CD. It can be used to
both count up on one input and down on the other.::
CTUD: ( BOOL:CU, BOOL:CD, BOOL:R, BOOL:LD, INT:PV ) => ( BOOL:QU, BOOL:QD, INT:CV )
CTUD_DINT: ( BOOL:CU, BOOL:CD, BOOL:R, BOOL:LD, DINT:PV ) => ( BOOL:QU, BOOL:QD, DINT:CV )
CTUD_LINT: ( BOOL:CU, BOOL:CD, BOOL:R, BOOL:LD, LINT:PV ) => ( BOOL:QU, BOOL:QD, LINT:CV )
CTUD_UDINT: ( BOOL:CU, BOOL:CD, BOOL:R, BOOL:LD, UDINT:PV ) => ( BOOL:QU, BOOL:QD, UDINT:CV )
CTUD_ULINT: ( BOOL:CU, BOOL:CD, BOOL:R, BOOL:LD, ULINT:PV ) => ( BOOL:QU, BOOL:QD, ULINT:CV )
This function represents an up-down programmable counter. A
rising-edge on the CU (COUNT-UP) input increments the counter
by one while a rising-edge on the CD (COUNT-DOWN) decreases
the current value. Applying a TRUE signal on R input will reset the
counter to zero. A TRUE condition on the LD signal will load the
counter with the value applied to the input PV (PROGRAMMED
VALUE). QU output becomes active when the current counting
value is greater or equal to the programmed value. The QD output
becomes active when the current value is less or equal to zero.
The CV output reports the current counter value.
* - .. figure:: std_block-037.png
TP
Pulse timer
- The pulse timer can be used to generate output pulses of a given
time duration.::
( BOOL:IN, TIME:PT ) => ( BOOL:Q, TIME:ET )
This kind of timer has the same behaviour of a single-shot timer or
a monostable timer.
When a rising-edge transition is detected on the IN input, the Q
output becomes TRUE immediately. This condition continues until
the programmed time PT, applied to the relative pin, is elapsed.
After that the PT is elapsed, the Q output keeps the ON state if
the input IN is still asserted else the Q output returns to the OFF
state. This timer is not re-triggerable. This means that after that
the timer has started it can't be stopped until the complete
session ends. The ET output reports the current elapsed time.
* - .. figure:: std_block-042.png
TON
On-delay timer
- The on-delay timer can be used to delay setting an output true,
for fixed period after an input becomes true.::
( BOOL:IN, TIME:PT ) => ( BOOL:Q, TIME:ET )
Asserting the input signal IN of this function starts the timer.
When the programmed time, applied to the input PT, is elapsed
and the input IN is still asserted, the Q output becomes TRUE. This
condition will continue until the input IN is released. If the IN
input is released before time elapsing, the timer will be cleared.
The ET output reports the current elapsed time.
* - .. figure:: std_block-044.png
TOF
Off-delay timer
- The off-delay timer can be used to delay setting an output false,
for fixed period after input goes false.::
( BOOL:IN, TIME:PT ) => ( BOOL:Q, TIME:ET )
Asserting the input signal IN of this function immediately activates
the Q output. At this point, releasing the input IN will start the
time elapsing. When the programmed time, applied to the input
PT, is elapsed and the input IN is still released, the Q output
becomes FALSE. This condition will be kept until the input IN is
released. If the IN input is asserted again before time elapses, the
timer will be cleared and the Q output remains TRUE. The ET
output reports the current elapsed time.
Additional function blocks
--------------------------
.. list-table::
* - .. figure:: std_block-055.png
RTC
Real Time Clock
- The RTC function block sets the output CDT to the input value PDT at the next
evaluation of the function block following a transition from 0 to 1 of the IN input. The CDT output
of the RTC function block is undefined when the value of IN is 0.
.. line-block::
PDT = Preset date and time, loaded on rising edge of IN
CDT = Current date and time, valid when IN=1
Q = copy of EN
.. code-block::
(BOOL:IN, PDT:DT) => (BOOL:Q, CDT:DT)
* - .. figure:: std_block-049.png
INTEGRAL
Integral
- The integral function block integrates the value of input XIN over
time.::
( BOOL:RUN, BOOL:R1, REAL:XIN, REAL:X0, TIME:CYCLE ) => ( BOOL:Q, REAL:XOUT )
When input RUN is True and override R1 is False, XOUT will
change for XIN value depends on CYCLE time value sampling
period. When RUN is False and override R1 is True, XOUT will hold
the last output value. If R1 is True, XOUT will be set to the X0
value.::
XOUT = XOUT + (XIN * CYCLE)
* - .. figure:: std_block-051.png
DERIVATIVE
Derivative
- The derivative function block produces an output XOUT
proportional to the rate of change of the input XIN.::
( BOOL:RUN, REAL:XIN, TIME:CYCLE ) => ( REAL:XOUT )
When RUN is True, XOUT will change proportional to the rate of
changing of the value XIN depends on CYCLE time value sampling
period.::
XOUT = ((3 * (XIN - XIN(to-3))) + XIN(to-1) – XIN(to-2) ) / (10 * CYCLE)
* - .. figure:: std_block-060.png
PID
Proportional, Integral, Derivative
- The PID (Proportional, Integral, Derivative) function block
provides the classical three term controller for closed loop
control. It does not contain any output limitation parameters
(dead-band, minimum, maximum, …) or other parameters
normally used for real process control (see also PID_A).::
( BOOL:AUTO, REAL:PV, REAL:SP, REAL:X0, REAL:KP, REAL:TR, REAL:TD, TIME:CYCLE ) => ( REAL:XOUT )
When AUTO is False, PID function block XOUT will follow X0 value.
When AUTO is True, XOUT will be calculated from error value (PV
process variable – SP set point), KP proportional constant, TR
reset time, TD derivative constant and CYCLE time value sampling
period.::
XOUT = KP * ((PV-SP) + (I_OUT/TR) + (D_OUT * TD))
* - .. figure:: std_block-062.png
RAMP
Ramp
- The RAMP function block is modelled on example given in the
standard but with the addition of a 'Holdback' feature.::
( BOOL:RUN, REAL:X0, REAL:X1, TIME:TR, TIME:CYCLE, BOOL:HOLDBACK, REAL:ERROR, REAL:PV ) => ( BOOL:RAMP, REAL:XOUT )
When RUN and HOLDBACK are False, XOUT will follow X0 value.
When RUN is True and HOLDBACK value is False, XOUT will change
for ``OUT(to-1) + (X1 – XOUT(to-1))`` every CYCLE time value sampling
period.
* - .. figure:: std_block-064.png
HYSTERESIS
Hysteresis
- The hysteresis function block provides a hysteresis boolean output
driven by the difference of two floating point (REAL) inputs XIN1
and XIN2.::
( REAL:XIN1, REAL:XIN2, REAL:EPS ) => ( BOOL:Q )
When XIN1 value will be grater than XIN2 + EPS value, Q becomes
True. When XIN1 value will be less than XIN2 - EPS value, Q
becomes False.