--- a/NEWS Thu Nov 04 09:32:58 2010 +0100
+++ b/NEWS Thu Dec 15 13:21:32 2011 +0100
@@ -30,7 +30,8 @@
* Added 8139too driver for kernels 2.6.25 (F. Pose), 2.6.26 (M. Luescher),
2.6.27, 2.6.28, 2.6.29 (M. Goetze), 2.6.31 (F. Pose), 2.6.32 (F. Pose),
2.6.34 (Malcolm Lewis), 2.6.36 (F. Pose) and 2.6.37 (F. Pose).
-* Added e1000 driver for 2.6.26 (M. Luescher), 2.6.27 and 2.6.28.
+* Added e1000 driver for 2.6.26 (M. Luescher), 2.6.27, 2.6.28, 2.6.29 and
+ 2.6.32.
* Added r8169 driver for 2.6.24, 2.6.27, 2.6.28, 2.6.29, 2.6.31 and 2.6.32
(latter thanks to Robbie K).
* Debug interfaces are created with the Ethernet addresses of the attached
--- a/devices/e1000/Makefile.am Thu Nov 04 09:32:58 2010 +0100
+++ b/devices/e1000/Makefile.am Thu Dec 15 13:21:32 2011 +0100
@@ -20,7 +20,7 @@
# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
#
# ---
-#
+#
# The license mentioned above concerns the source code only. Using the
# EtherCAT technology and brand is only permitted in compliance with the
# industrial property and similar rights of Beckhoff Automation GmbH.
@@ -48,6 +48,8 @@
e1000-2.6.28-orig.h \
e1000-2.6.29-ethercat.h \
e1000-2.6.29-orig.h \
+ e1000-2.6.32-ethercat.h \
+ e1000-2.6.32-orig.h \
e1000_ethtool-2.6.13-ethercat.c \
e1000_ethtool-2.6.13-orig.c \
e1000_ethtool-2.6.18-ethercat.c \
@@ -66,6 +68,8 @@
e1000_ethtool-2.6.28-orig.c \
e1000_ethtool-2.6.29-ethercat.c \
e1000_ethtool-2.6.29-orig.c \
+ e1000_ethtool-2.6.32-ethercat.c \
+ e1000_ethtool-2.6.32-orig.c \
e1000_hw-2.6.13-ethercat.c \
e1000_hw-2.6.13-ethercat.h \
e1000_hw-2.6.13-orig.c \
@@ -102,6 +106,10 @@
e1000_hw-2.6.29-ethercat.h \
e1000_hw-2.6.29-orig.c \
e1000_hw-2.6.29-orig.h \
+ e1000_hw-2.6.32-ethercat.c \
+ e1000_hw-2.6.32-ethercat.h \
+ e1000_hw-2.6.32-orig.c \
+ e1000_hw-2.6.32-orig.h \
e1000_main-2.6.13-ethercat.c \
e1000_main-2.6.13-orig.c \
e1000_main-2.6.18-ethercat.c \
@@ -120,6 +128,8 @@
e1000_main-2.6.28-orig.c \
e1000_main-2.6.29-ethercat.c \
e1000_main-2.6.29-orig.c \
+ e1000_main-2.6.32-ethercat.c \
+ e1000_main-2.6.32-orig.c \
e1000_osdep-2.6.13-ethercat.h \
e1000_osdep-2.6.13-orig.h \
e1000_osdep-2.6.18-ethercat.h \
@@ -138,6 +148,8 @@
e1000_osdep-2.6.28-orig.h \
e1000_osdep-2.6.29-ethercat.h \
e1000_osdep-2.6.29-orig.h \
+ e1000_osdep-2.6.32-ethercat.h \
+ e1000_osdep-2.6.32-orig.h \
e1000_param-2.6.13-ethercat.c \
e1000_param-2.6.13-orig.c \
e1000_param-2.6.18-ethercat.c \
@@ -155,7 +167,9 @@
e1000_param-2.6.28-ethercat.c \
e1000_param-2.6.28-orig.c \
e1000_param-2.6.29-ethercat.c \
- e1000_param-2.6.29-orig.c
+ e1000_param-2.6.29-orig.c \
+ e1000_param-2.6.32-ethercat.c \
+ e1000_param-2.6.32-orig.c
BUILT_SOURCES = \
Kbuild
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000-2.6.32-ethercat.h Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,361 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+
+/* Linux PRO/1000 Ethernet Driver main header file */
+
+#ifndef _E1000_H_
+#define _E1000_H_
+
+#include <linux/stddef.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <asm/byteorder.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/slab.h>
+#include <linux/vmalloc.h>
+#include <linux/interrupt.h>
+#include <linux/string.h>
+#include <linux/pagemap.h>
+#include <linux/dma-mapping.h>
+#include <linux/bitops.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <linux/capability.h>
+#include <linux/in.h>
+#include <linux/ip.h>
+#include <linux/ipv6.h>
+#include <linux/tcp.h>
+#include <linux/udp.h>
+#include <net/pkt_sched.h>
+#include <linux/list.h>
+#include <linux/reboot.h>
+#include <net/checksum.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/if_vlan.h>
+#include "../ecdev.h"
+
+
+#define BAR_0 0
+#define BAR_1 1
+#define BAR_5 5
+
+#define INTEL_E1000_ETHERNET_DEVICE(device_id) {\
+ PCI_DEVICE(PCI_VENDOR_ID_INTEL, device_id)}
+
+struct e1000_adapter;
+
+#include "e1000_hw-2.6.32-ethercat.h"
+
+#ifdef DBG
+#define E1000_DBG(args...) printk(KERN_DEBUG "ec_e1000: " args)
+#else
+#define E1000_DBG(args...)
+#endif
+
+#define E1000_ERR(args...) printk(KERN_ERR "ec_e1000: " args)
+
+#define PFX "ec_e1000: "
+
+#define DPRINTK(nlevel, klevel, fmt, args...) \
+do { \
+ if (NETIF_MSG_##nlevel & adapter->msg_enable) \
+ printk(KERN_##klevel PFX "%s: %s: " fmt, \
+ adapter->netdev->name, __func__, ##args); \
+} while (0)
+
+#define E1000_MAX_INTR 10
+
+/* TX/RX descriptor defines */
+#define E1000_DEFAULT_TXD 256
+#define E1000_MAX_TXD 256
+#define E1000_MIN_TXD 80
+#define E1000_MAX_82544_TXD 4096
+
+#define E1000_DEFAULT_RXD 256
+#define E1000_MAX_RXD 256
+#define E1000_MIN_RXD 80
+#define E1000_MAX_82544_RXD 4096
+
+#define E1000_MIN_ITR_USECS 10 /* 100000 irq/sec */
+#define E1000_MAX_ITR_USECS 10000 /* 100 irq/sec */
+
+/* this is the size past which hardware will drop packets when setting LPE=0 */
+#define MAXIMUM_ETHERNET_VLAN_SIZE 1522
+
+/* Supported Rx Buffer Sizes */
+#define E1000_RXBUFFER_128 128 /* Used for packet split */
+#define E1000_RXBUFFER_256 256 /* Used for packet split */
+#define E1000_RXBUFFER_512 512
+#define E1000_RXBUFFER_1024 1024
+#define E1000_RXBUFFER_2048 2048
+#define E1000_RXBUFFER_4096 4096
+#define E1000_RXBUFFER_8192 8192
+#define E1000_RXBUFFER_16384 16384
+
+/* SmartSpeed delimiters */
+#define E1000_SMARTSPEED_DOWNSHIFT 3
+#define E1000_SMARTSPEED_MAX 15
+
+/* Packet Buffer allocations */
+#define E1000_PBA_BYTES_SHIFT 0xA
+#define E1000_TX_HEAD_ADDR_SHIFT 7
+#define E1000_PBA_TX_MASK 0xFFFF0000
+
+/* Flow Control Watermarks */
+#define E1000_FC_HIGH_DIFF 0x1638 /* High: 5688 bytes below Rx FIFO size */
+#define E1000_FC_LOW_DIFF 0x1640 /* Low: 5696 bytes below Rx FIFO size */
+
+#define E1000_FC_PAUSE_TIME 0xFFFF /* pause for the max or until send xon */
+
+/* How many Tx Descriptors do we need to call netif_wake_queue ? */
+#define E1000_TX_QUEUE_WAKE 16
+/* How many Rx Buffers do we bundle into one write to the hardware ? */
+#define E1000_RX_BUFFER_WRITE 16 /* Must be power of 2 */
+
+#define AUTO_ALL_MODES 0
+#define E1000_EEPROM_82544_APM 0x0004
+#define E1000_EEPROM_APME 0x0400
+
+#ifndef E1000_MASTER_SLAVE
+/* Switch to override PHY master/slave setting */
+#define E1000_MASTER_SLAVE e1000_ms_hw_default
+#endif
+
+#define E1000_MNG_VLAN_NONE (-1)
+
+/* wrapper around a pointer to a socket buffer,
+ * so a DMA handle can be stored along with the buffer */
+struct e1000_buffer {
+ struct sk_buff *skb;
+ dma_addr_t dma;
+ struct page *page;
+ unsigned long time_stamp;
+ u16 length;
+ u16 next_to_watch;
+};
+
+struct e1000_tx_ring {
+ /* pointer to the descriptor ring memory */
+ void *desc;
+ /* physical address of the descriptor ring */
+ dma_addr_t dma;
+ /* length of descriptor ring in bytes */
+ unsigned int size;
+ /* number of descriptors in the ring */
+ unsigned int count;
+ /* next descriptor to associate a buffer with */
+ unsigned int next_to_use;
+ /* next descriptor to check for DD status bit */
+ unsigned int next_to_clean;
+ /* array of buffer information structs */
+ struct e1000_buffer *buffer_info;
+
+ u16 tdh;
+ u16 tdt;
+ bool last_tx_tso;
+};
+
+struct e1000_rx_ring {
+ /* pointer to the descriptor ring memory */
+ void *desc;
+ /* physical address of the descriptor ring */
+ dma_addr_t dma;
+ /* length of descriptor ring in bytes */
+ unsigned int size;
+ /* number of descriptors in the ring */
+ unsigned int count;
+ /* next descriptor to associate a buffer with */
+ unsigned int next_to_use;
+ /* next descriptor to check for DD status bit */
+ unsigned int next_to_clean;
+ /* array of buffer information structs */
+ struct e1000_buffer *buffer_info;
+ struct sk_buff *rx_skb_top;
+
+ /* cpu for rx queue */
+ int cpu;
+
+ u16 rdh;
+ u16 rdt;
+};
+
+#define E1000_DESC_UNUSED(R) \
+ ((((R)->next_to_clean > (R)->next_to_use) \
+ ? 0 : (R)->count) + (R)->next_to_clean - (R)->next_to_use - 1)
+
+#define E1000_RX_DESC_EXT(R, i) \
+ (&(((union e1000_rx_desc_extended *)((R).desc))[i]))
+#define E1000_GET_DESC(R, i, type) (&(((struct type *)((R).desc))[i]))
+#define E1000_RX_DESC(R, i) E1000_GET_DESC(R, i, e1000_rx_desc)
+#define E1000_TX_DESC(R, i) E1000_GET_DESC(R, i, e1000_tx_desc)
+#define E1000_CONTEXT_DESC(R, i) E1000_GET_DESC(R, i, e1000_context_desc)
+
+/* board specific private data structure */
+
+struct e1000_adapter {
+ struct timer_list tx_fifo_stall_timer;
+ struct timer_list watchdog_timer;
+ struct timer_list phy_info_timer;
+ struct vlan_group *vlgrp;
+ u16 mng_vlan_id;
+ u32 bd_number;
+ u32 rx_buffer_len;
+ u32 wol;
+ u32 smartspeed;
+ u32 en_mng_pt;
+ u16 link_speed;
+ u16 link_duplex;
+ spinlock_t stats_lock;
+ unsigned int total_tx_bytes;
+ unsigned int total_tx_packets;
+ unsigned int total_rx_bytes;
+ unsigned int total_rx_packets;
+ /* Interrupt Throttle Rate */
+ u32 itr;
+ u32 itr_setting;
+ u16 tx_itr;
+ u16 rx_itr;
+
+ struct work_struct reset_task;
+ u8 fc_autoneg;
+
+ struct timer_list blink_timer;
+ unsigned long led_status;
+
+ /* TX */
+ struct e1000_tx_ring *tx_ring; /* One per active queue */
+ unsigned int restart_queue;
+ unsigned long tx_queue_len;
+ u32 txd_cmd;
+ u32 tx_int_delay;
+ u32 tx_abs_int_delay;
+ u32 gotcl;
+ u64 gotcl_old;
+ u64 tpt_old;
+ u64 colc_old;
+ u32 tx_timeout_count;
+ u32 tx_fifo_head;
+ u32 tx_head_addr;
+ u32 tx_fifo_size;
+ u8 tx_timeout_factor;
+ atomic_t tx_fifo_stall;
+ bool pcix_82544;
+ bool detect_tx_hung;
+
+ /* RX */
+ bool (*clean_rx)(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int *work_done, int work_to_do);
+ void (*alloc_rx_buf)(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int cleaned_count);
+ struct e1000_rx_ring *rx_ring; /* One per active queue */
+ struct napi_struct napi;
+
+ int num_tx_queues;
+ int num_rx_queues;
+
+ u64 hw_csum_err;
+ u64 hw_csum_good;
+ u32 alloc_rx_buff_failed;
+ u32 rx_int_delay;
+ u32 rx_abs_int_delay;
+ bool rx_csum;
+ u32 gorcl;
+ u64 gorcl_old;
+
+ /* OS defined structs */
+ struct net_device *netdev;
+ struct pci_dev *pdev;
+ struct net_device_stats net_stats;
+
+ /* structs defined in e1000_hw.h */
+ struct e1000_hw hw;
+ struct e1000_hw_stats stats;
+ struct e1000_phy_info phy_info;
+ struct e1000_phy_stats phy_stats;
+
+ u32 test_icr;
+ struct e1000_tx_ring test_tx_ring;
+ struct e1000_rx_ring test_rx_ring;
+
+ int msg_enable;
+
+ /* to not mess up cache alignment, always add to the bottom */
+ bool tso_force;
+ bool smart_power_down; /* phy smart power down */
+ bool quad_port_a;
+ unsigned long flags;
+ u32 eeprom_wol;
+
+ /* for ioport free */
+ int bars;
+ int need_ioport;
+
+ bool discarding;
+
+ ec_device_t *ecdev;
+ unsigned long ec_watchdog_jiffies;
+};
+
+enum e1000_state_t {
+ __E1000_TESTING,
+ __E1000_RESETTING,
+ __E1000_DOWN
+};
+
+extern char e1000_driver_name[];
+extern const char e1000_driver_version[];
+
+extern int e1000_up(struct e1000_adapter *adapter);
+extern void e1000_down(struct e1000_adapter *adapter);
+extern void e1000_reinit_locked(struct e1000_adapter *adapter);
+extern void e1000_reset(struct e1000_adapter *adapter);
+extern int e1000_set_spd_dplx(struct e1000_adapter *adapter, u16 spddplx);
+extern int e1000_setup_all_rx_resources(struct e1000_adapter *adapter);
+extern int e1000_setup_all_tx_resources(struct e1000_adapter *adapter);
+extern void e1000_free_all_rx_resources(struct e1000_adapter *adapter);
+extern void e1000_free_all_tx_resources(struct e1000_adapter *adapter);
+extern void e1000_update_stats(struct e1000_adapter *adapter);
+extern void e1000_power_up_phy(struct e1000_adapter *);
+extern void e1000_set_ethtool_ops(struct net_device *netdev);
+extern void e1000_check_options(struct e1000_adapter *adapter);
+
+#endif /* _E1000_H_ */
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000-2.6.32-orig.h Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,356 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+
+/* Linux PRO/1000 Ethernet Driver main header file */
+
+#ifndef _E1000_H_
+#define _E1000_H_
+
+#include <linux/stddef.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <asm/byteorder.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/slab.h>
+#include <linux/vmalloc.h>
+#include <linux/interrupt.h>
+#include <linux/string.h>
+#include <linux/pagemap.h>
+#include <linux/dma-mapping.h>
+#include <linux/bitops.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <linux/capability.h>
+#include <linux/in.h>
+#include <linux/ip.h>
+#include <linux/ipv6.h>
+#include <linux/tcp.h>
+#include <linux/udp.h>
+#include <net/pkt_sched.h>
+#include <linux/list.h>
+#include <linux/reboot.h>
+#include <net/checksum.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/if_vlan.h>
+
+#define BAR_0 0
+#define BAR_1 1
+#define BAR_5 5
+
+#define INTEL_E1000_ETHERNET_DEVICE(device_id) {\
+ PCI_DEVICE(PCI_VENDOR_ID_INTEL, device_id)}
+
+struct e1000_adapter;
+
+#include "e1000_hw.h"
+
+#ifdef DBG
+#define E1000_DBG(args...) printk(KERN_DEBUG "e1000: " args)
+#else
+#define E1000_DBG(args...)
+#endif
+
+#define E1000_ERR(args...) printk(KERN_ERR "e1000: " args)
+
+#define PFX "e1000: "
+
+#define DPRINTK(nlevel, klevel, fmt, args...) \
+do { \
+ if (NETIF_MSG_##nlevel & adapter->msg_enable) \
+ printk(KERN_##klevel PFX "%s: %s: " fmt, \
+ adapter->netdev->name, __func__, ##args); \
+} while (0)
+
+#define E1000_MAX_INTR 10
+
+/* TX/RX descriptor defines */
+#define E1000_DEFAULT_TXD 256
+#define E1000_MAX_TXD 256
+#define E1000_MIN_TXD 80
+#define E1000_MAX_82544_TXD 4096
+
+#define E1000_DEFAULT_RXD 256
+#define E1000_MAX_RXD 256
+#define E1000_MIN_RXD 80
+#define E1000_MAX_82544_RXD 4096
+
+#define E1000_MIN_ITR_USECS 10 /* 100000 irq/sec */
+#define E1000_MAX_ITR_USECS 10000 /* 100 irq/sec */
+
+/* this is the size past which hardware will drop packets when setting LPE=0 */
+#define MAXIMUM_ETHERNET_VLAN_SIZE 1522
+
+/* Supported Rx Buffer Sizes */
+#define E1000_RXBUFFER_128 128 /* Used for packet split */
+#define E1000_RXBUFFER_256 256 /* Used for packet split */
+#define E1000_RXBUFFER_512 512
+#define E1000_RXBUFFER_1024 1024
+#define E1000_RXBUFFER_2048 2048
+#define E1000_RXBUFFER_4096 4096
+#define E1000_RXBUFFER_8192 8192
+#define E1000_RXBUFFER_16384 16384
+
+/* SmartSpeed delimiters */
+#define E1000_SMARTSPEED_DOWNSHIFT 3
+#define E1000_SMARTSPEED_MAX 15
+
+/* Packet Buffer allocations */
+#define E1000_PBA_BYTES_SHIFT 0xA
+#define E1000_TX_HEAD_ADDR_SHIFT 7
+#define E1000_PBA_TX_MASK 0xFFFF0000
+
+/* Flow Control Watermarks */
+#define E1000_FC_HIGH_DIFF 0x1638 /* High: 5688 bytes below Rx FIFO size */
+#define E1000_FC_LOW_DIFF 0x1640 /* Low: 5696 bytes below Rx FIFO size */
+
+#define E1000_FC_PAUSE_TIME 0xFFFF /* pause for the max or until send xon */
+
+/* How many Tx Descriptors do we need to call netif_wake_queue ? */
+#define E1000_TX_QUEUE_WAKE 16
+/* How many Rx Buffers do we bundle into one write to the hardware ? */
+#define E1000_RX_BUFFER_WRITE 16 /* Must be power of 2 */
+
+#define AUTO_ALL_MODES 0
+#define E1000_EEPROM_82544_APM 0x0004
+#define E1000_EEPROM_APME 0x0400
+
+#ifndef E1000_MASTER_SLAVE
+/* Switch to override PHY master/slave setting */
+#define E1000_MASTER_SLAVE e1000_ms_hw_default
+#endif
+
+#define E1000_MNG_VLAN_NONE (-1)
+
+/* wrapper around a pointer to a socket buffer,
+ * so a DMA handle can be stored along with the buffer */
+struct e1000_buffer {
+ struct sk_buff *skb;
+ dma_addr_t dma;
+ struct page *page;
+ unsigned long time_stamp;
+ u16 length;
+ u16 next_to_watch;
+};
+
+struct e1000_tx_ring {
+ /* pointer to the descriptor ring memory */
+ void *desc;
+ /* physical address of the descriptor ring */
+ dma_addr_t dma;
+ /* length of descriptor ring in bytes */
+ unsigned int size;
+ /* number of descriptors in the ring */
+ unsigned int count;
+ /* next descriptor to associate a buffer with */
+ unsigned int next_to_use;
+ /* next descriptor to check for DD status bit */
+ unsigned int next_to_clean;
+ /* array of buffer information structs */
+ struct e1000_buffer *buffer_info;
+
+ u16 tdh;
+ u16 tdt;
+ bool last_tx_tso;
+};
+
+struct e1000_rx_ring {
+ /* pointer to the descriptor ring memory */
+ void *desc;
+ /* physical address of the descriptor ring */
+ dma_addr_t dma;
+ /* length of descriptor ring in bytes */
+ unsigned int size;
+ /* number of descriptors in the ring */
+ unsigned int count;
+ /* next descriptor to associate a buffer with */
+ unsigned int next_to_use;
+ /* next descriptor to check for DD status bit */
+ unsigned int next_to_clean;
+ /* array of buffer information structs */
+ struct e1000_buffer *buffer_info;
+ struct sk_buff *rx_skb_top;
+
+ /* cpu for rx queue */
+ int cpu;
+
+ u16 rdh;
+ u16 rdt;
+};
+
+#define E1000_DESC_UNUSED(R) \
+ ((((R)->next_to_clean > (R)->next_to_use) \
+ ? 0 : (R)->count) + (R)->next_to_clean - (R)->next_to_use - 1)
+
+#define E1000_RX_DESC_EXT(R, i) \
+ (&(((union e1000_rx_desc_extended *)((R).desc))[i]))
+#define E1000_GET_DESC(R, i, type) (&(((struct type *)((R).desc))[i]))
+#define E1000_RX_DESC(R, i) E1000_GET_DESC(R, i, e1000_rx_desc)
+#define E1000_TX_DESC(R, i) E1000_GET_DESC(R, i, e1000_tx_desc)
+#define E1000_CONTEXT_DESC(R, i) E1000_GET_DESC(R, i, e1000_context_desc)
+
+/* board specific private data structure */
+
+struct e1000_adapter {
+ struct timer_list tx_fifo_stall_timer;
+ struct timer_list watchdog_timer;
+ struct timer_list phy_info_timer;
+ struct vlan_group *vlgrp;
+ u16 mng_vlan_id;
+ u32 bd_number;
+ u32 rx_buffer_len;
+ u32 wol;
+ u32 smartspeed;
+ u32 en_mng_pt;
+ u16 link_speed;
+ u16 link_duplex;
+ spinlock_t stats_lock;
+ unsigned int total_tx_bytes;
+ unsigned int total_tx_packets;
+ unsigned int total_rx_bytes;
+ unsigned int total_rx_packets;
+ /* Interrupt Throttle Rate */
+ u32 itr;
+ u32 itr_setting;
+ u16 tx_itr;
+ u16 rx_itr;
+
+ struct work_struct reset_task;
+ u8 fc_autoneg;
+
+ struct timer_list blink_timer;
+ unsigned long led_status;
+
+ /* TX */
+ struct e1000_tx_ring *tx_ring; /* One per active queue */
+ unsigned int restart_queue;
+ unsigned long tx_queue_len;
+ u32 txd_cmd;
+ u32 tx_int_delay;
+ u32 tx_abs_int_delay;
+ u32 gotcl;
+ u64 gotcl_old;
+ u64 tpt_old;
+ u64 colc_old;
+ u32 tx_timeout_count;
+ u32 tx_fifo_head;
+ u32 tx_head_addr;
+ u32 tx_fifo_size;
+ u8 tx_timeout_factor;
+ atomic_t tx_fifo_stall;
+ bool pcix_82544;
+ bool detect_tx_hung;
+
+ /* RX */
+ bool (*clean_rx)(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int *work_done, int work_to_do);
+ void (*alloc_rx_buf)(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int cleaned_count);
+ struct e1000_rx_ring *rx_ring; /* One per active queue */
+ struct napi_struct napi;
+
+ int num_tx_queues;
+ int num_rx_queues;
+
+ u64 hw_csum_err;
+ u64 hw_csum_good;
+ u32 alloc_rx_buff_failed;
+ u32 rx_int_delay;
+ u32 rx_abs_int_delay;
+ bool rx_csum;
+ u32 gorcl;
+ u64 gorcl_old;
+
+ /* OS defined structs */
+ struct net_device *netdev;
+ struct pci_dev *pdev;
+ struct net_device_stats net_stats;
+
+ /* structs defined in e1000_hw.h */
+ struct e1000_hw hw;
+ struct e1000_hw_stats stats;
+ struct e1000_phy_info phy_info;
+ struct e1000_phy_stats phy_stats;
+
+ u32 test_icr;
+ struct e1000_tx_ring test_tx_ring;
+ struct e1000_rx_ring test_rx_ring;
+
+ int msg_enable;
+
+ /* to not mess up cache alignment, always add to the bottom */
+ bool tso_force;
+ bool smart_power_down; /* phy smart power down */
+ bool quad_port_a;
+ unsigned long flags;
+ u32 eeprom_wol;
+
+ /* for ioport free */
+ int bars;
+ int need_ioport;
+
+ bool discarding;
+};
+
+enum e1000_state_t {
+ __E1000_TESTING,
+ __E1000_RESETTING,
+ __E1000_DOWN
+};
+
+extern char e1000_driver_name[];
+extern const char e1000_driver_version[];
+
+extern int e1000_up(struct e1000_adapter *adapter);
+extern void e1000_down(struct e1000_adapter *adapter);
+extern void e1000_reinit_locked(struct e1000_adapter *adapter);
+extern void e1000_reset(struct e1000_adapter *adapter);
+extern int e1000_set_spd_dplx(struct e1000_adapter *adapter, u16 spddplx);
+extern int e1000_setup_all_rx_resources(struct e1000_adapter *adapter);
+extern int e1000_setup_all_tx_resources(struct e1000_adapter *adapter);
+extern void e1000_free_all_rx_resources(struct e1000_adapter *adapter);
+extern void e1000_free_all_tx_resources(struct e1000_adapter *adapter);
+extern void e1000_update_stats(struct e1000_adapter *adapter);
+extern void e1000_power_up_phy(struct e1000_adapter *);
+extern void e1000_set_ethtool_ops(struct net_device *netdev);
+extern void e1000_check_options(struct e1000_adapter *adapter);
+
+#endif /* _E1000_H_ */
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_ethtool-2.6.32-ethercat.c Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,1924 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/* ethtool support for e1000 */
+
+#include "e1000-2.6.32-ethercat.h"
+#include <asm/uaccess.h>
+
+struct e1000_stats {
+ char stat_string[ETH_GSTRING_LEN];
+ int sizeof_stat;
+ int stat_offset;
+};
+
+#define E1000_STAT(m) FIELD_SIZEOF(struct e1000_adapter, m), \
+ offsetof(struct e1000_adapter, m)
+static const struct e1000_stats e1000_gstrings_stats[] = {
+ { "rx_packets", E1000_STAT(stats.gprc) },
+ { "tx_packets", E1000_STAT(stats.gptc) },
+ { "rx_bytes", E1000_STAT(stats.gorcl) },
+ { "tx_bytes", E1000_STAT(stats.gotcl) },
+ { "rx_broadcast", E1000_STAT(stats.bprc) },
+ { "tx_broadcast", E1000_STAT(stats.bptc) },
+ { "rx_multicast", E1000_STAT(stats.mprc) },
+ { "tx_multicast", E1000_STAT(stats.mptc) },
+ { "rx_errors", E1000_STAT(stats.rxerrc) },
+ { "tx_errors", E1000_STAT(stats.txerrc) },
+ { "tx_dropped", E1000_STAT(net_stats.tx_dropped) },
+ { "multicast", E1000_STAT(stats.mprc) },
+ { "collisions", E1000_STAT(stats.colc) },
+ { "rx_length_errors", E1000_STAT(stats.rlerrc) },
+ { "rx_over_errors", E1000_STAT(net_stats.rx_over_errors) },
+ { "rx_crc_errors", E1000_STAT(stats.crcerrs) },
+ { "rx_frame_errors", E1000_STAT(net_stats.rx_frame_errors) },
+ { "rx_no_buffer_count", E1000_STAT(stats.rnbc) },
+ { "rx_missed_errors", E1000_STAT(stats.mpc) },
+ { "tx_aborted_errors", E1000_STAT(stats.ecol) },
+ { "tx_carrier_errors", E1000_STAT(stats.tncrs) },
+ { "tx_fifo_errors", E1000_STAT(net_stats.tx_fifo_errors) },
+ { "tx_heartbeat_errors", E1000_STAT(net_stats.tx_heartbeat_errors) },
+ { "tx_window_errors", E1000_STAT(stats.latecol) },
+ { "tx_abort_late_coll", E1000_STAT(stats.latecol) },
+ { "tx_deferred_ok", E1000_STAT(stats.dc) },
+ { "tx_single_coll_ok", E1000_STAT(stats.scc) },
+ { "tx_multi_coll_ok", E1000_STAT(stats.mcc) },
+ { "tx_timeout_count", E1000_STAT(tx_timeout_count) },
+ { "tx_restart_queue", E1000_STAT(restart_queue) },
+ { "rx_long_length_errors", E1000_STAT(stats.roc) },
+ { "rx_short_length_errors", E1000_STAT(stats.ruc) },
+ { "rx_align_errors", E1000_STAT(stats.algnerrc) },
+ { "tx_tcp_seg_good", E1000_STAT(stats.tsctc) },
+ { "tx_tcp_seg_failed", E1000_STAT(stats.tsctfc) },
+ { "rx_flow_control_xon", E1000_STAT(stats.xonrxc) },
+ { "rx_flow_control_xoff", E1000_STAT(stats.xoffrxc) },
+ { "tx_flow_control_xon", E1000_STAT(stats.xontxc) },
+ { "tx_flow_control_xoff", E1000_STAT(stats.xofftxc) },
+ { "rx_long_byte_count", E1000_STAT(stats.gorcl) },
+ { "rx_csum_offload_good", E1000_STAT(hw_csum_good) },
+ { "rx_csum_offload_errors", E1000_STAT(hw_csum_err) },
+ { "alloc_rx_buff_failed", E1000_STAT(alloc_rx_buff_failed) },
+ { "tx_smbus", E1000_STAT(stats.mgptc) },
+ { "rx_smbus", E1000_STAT(stats.mgprc) },
+ { "dropped_smbus", E1000_STAT(stats.mgpdc) },
+};
+
+#define E1000_QUEUE_STATS_LEN 0
+#define E1000_GLOBAL_STATS_LEN ARRAY_SIZE(e1000_gstrings_stats)
+#define E1000_STATS_LEN (E1000_GLOBAL_STATS_LEN + E1000_QUEUE_STATS_LEN)
+static const char e1000_gstrings_test[][ETH_GSTRING_LEN] = {
+ "Register test (offline)", "Eeprom test (offline)",
+ "Interrupt test (offline)", "Loopback test (offline)",
+ "Link test (on/offline)"
+};
+#define E1000_TEST_LEN ARRAY_SIZE(e1000_gstrings_test)
+
+static int e1000_get_settings(struct net_device *netdev,
+ struct ethtool_cmd *ecmd)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (hw->media_type == e1000_media_type_copper) {
+
+ ecmd->supported = (SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_1000baseT_Full|
+ SUPPORTED_Autoneg |
+ SUPPORTED_TP);
+ ecmd->advertising = ADVERTISED_TP;
+
+ if (hw->autoneg == 1) {
+ ecmd->advertising |= ADVERTISED_Autoneg;
+ /* the e1000 autoneg seems to match ethtool nicely */
+ ecmd->advertising |= hw->autoneg_advertised;
+ }
+
+ ecmd->port = PORT_TP;
+ ecmd->phy_address = hw->phy_addr;
+
+ if (hw->mac_type == e1000_82543)
+ ecmd->transceiver = XCVR_EXTERNAL;
+ else
+ ecmd->transceiver = XCVR_INTERNAL;
+
+ } else {
+ ecmd->supported = (SUPPORTED_1000baseT_Full |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Autoneg);
+
+ ecmd->advertising = (ADVERTISED_1000baseT_Full |
+ ADVERTISED_FIBRE |
+ ADVERTISED_Autoneg);
+
+ ecmd->port = PORT_FIBRE;
+
+ if (hw->mac_type >= e1000_82545)
+ ecmd->transceiver = XCVR_INTERNAL;
+ else
+ ecmd->transceiver = XCVR_EXTERNAL;
+ }
+
+ if (er32(STATUS) & E1000_STATUS_LU) {
+
+ e1000_get_speed_and_duplex(hw, &adapter->link_speed,
+ &adapter->link_duplex);
+ ecmd->speed = adapter->link_speed;
+
+ /* unfortunatly FULL_DUPLEX != DUPLEX_FULL
+ * and HALF_DUPLEX != DUPLEX_HALF */
+
+ if (adapter->link_duplex == FULL_DUPLEX)
+ ecmd->duplex = DUPLEX_FULL;
+ else
+ ecmd->duplex = DUPLEX_HALF;
+ } else {
+ ecmd->speed = -1;
+ ecmd->duplex = -1;
+ }
+
+ ecmd->autoneg = ((hw->media_type == e1000_media_type_fiber) ||
+ hw->autoneg) ? AUTONEG_ENABLE : AUTONEG_DISABLE;
+ return 0;
+}
+
+static int e1000_set_settings(struct net_device *netdev,
+ struct ethtool_cmd *ecmd)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (adapter->ecdev)
+ return -EBUSY;
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+
+ if (ecmd->autoneg == AUTONEG_ENABLE) {
+ hw->autoneg = 1;
+ if (hw->media_type == e1000_media_type_fiber)
+ hw->autoneg_advertised = ADVERTISED_1000baseT_Full |
+ ADVERTISED_FIBRE |
+ ADVERTISED_Autoneg;
+ else
+ hw->autoneg_advertised = ecmd->advertising |
+ ADVERTISED_TP |
+ ADVERTISED_Autoneg;
+ ecmd->advertising = hw->autoneg_advertised;
+ } else
+ if (e1000_set_spd_dplx(adapter, ecmd->speed + ecmd->duplex)) {
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+ return -EINVAL;
+ }
+
+ /* reset the link */
+
+ if (netif_running(adapter->netdev)) {
+ e1000_down(adapter);
+ e1000_up(adapter);
+ } else
+ e1000_reset(adapter);
+
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+ return 0;
+}
+
+static void e1000_get_pauseparam(struct net_device *netdev,
+ struct ethtool_pauseparam *pause)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ pause->autoneg =
+ (adapter->fc_autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE);
+
+ if (hw->fc == E1000_FC_RX_PAUSE)
+ pause->rx_pause = 1;
+ else if (hw->fc == E1000_FC_TX_PAUSE)
+ pause->tx_pause = 1;
+ else if (hw->fc == E1000_FC_FULL) {
+ pause->rx_pause = 1;
+ pause->tx_pause = 1;
+ }
+}
+
+static int e1000_set_pauseparam(struct net_device *netdev,
+ struct ethtool_pauseparam *pause)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ int retval = 0;
+
+ if (adapter->ecdev)
+ return -EBUSY;
+
+ adapter->fc_autoneg = pause->autoneg;
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+
+ if (pause->rx_pause && pause->tx_pause)
+ hw->fc = E1000_FC_FULL;
+ else if (pause->rx_pause && !pause->tx_pause)
+ hw->fc = E1000_FC_RX_PAUSE;
+ else if (!pause->rx_pause && pause->tx_pause)
+ hw->fc = E1000_FC_TX_PAUSE;
+ else if (!pause->rx_pause && !pause->tx_pause)
+ hw->fc = E1000_FC_NONE;
+
+ hw->original_fc = hw->fc;
+
+ if (adapter->fc_autoneg == AUTONEG_ENABLE) {
+ if (netif_running(adapter->netdev)) {
+ e1000_down(adapter);
+ e1000_up(adapter);
+ } else
+ e1000_reset(adapter);
+ } else
+ retval = ((hw->media_type == e1000_media_type_fiber) ?
+ e1000_setup_link(hw) : e1000_force_mac_fc(hw));
+
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+ return retval;
+}
+
+static u32 e1000_get_rx_csum(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ return adapter->rx_csum;
+}
+
+static int e1000_set_rx_csum(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (adapter->ecdev)
+ return -EBUSY;
+
+ adapter->rx_csum = data;
+
+ if (netif_running(netdev))
+ e1000_reinit_locked(adapter);
+ else
+ e1000_reset(adapter);
+ return 0;
+}
+
+static u32 e1000_get_tx_csum(struct net_device *netdev)
+{
+ return (netdev->features & NETIF_F_HW_CSUM) != 0;
+}
+
+static int e1000_set_tx_csum(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (hw->mac_type < e1000_82543) {
+ if (!data)
+ return -EINVAL;
+ return 0;
+ }
+
+ if (data)
+ netdev->features |= NETIF_F_HW_CSUM;
+ else
+ netdev->features &= ~NETIF_F_HW_CSUM;
+
+ return 0;
+}
+
+static int e1000_set_tso(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if ((hw->mac_type < e1000_82544) ||
+ (hw->mac_type == e1000_82547))
+ return data ? -EINVAL : 0;
+
+ if (data)
+ netdev->features |= NETIF_F_TSO;
+ else
+ netdev->features &= ~NETIF_F_TSO;
+
+ netdev->features &= ~NETIF_F_TSO6;
+
+ DPRINTK(PROBE, INFO, "TSO is %s\n", data ? "Enabled" : "Disabled");
+ adapter->tso_force = true;
+ return 0;
+}
+
+static u32 e1000_get_msglevel(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ return adapter->msg_enable;
+}
+
+static void e1000_set_msglevel(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ adapter->msg_enable = data;
+}
+
+static int e1000_get_regs_len(struct net_device *netdev)
+{
+#define E1000_REGS_LEN 32
+ return E1000_REGS_LEN * sizeof(u32);
+}
+
+static void e1000_get_regs(struct net_device *netdev, struct ethtool_regs *regs,
+ void *p)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 *regs_buff = p;
+ u16 phy_data;
+
+ memset(p, 0, E1000_REGS_LEN * sizeof(u32));
+
+ regs->version = (1 << 24) | (hw->revision_id << 16) | hw->device_id;
+
+ regs_buff[0] = er32(CTRL);
+ regs_buff[1] = er32(STATUS);
+
+ regs_buff[2] = er32(RCTL);
+ regs_buff[3] = er32(RDLEN);
+ regs_buff[4] = er32(RDH);
+ regs_buff[5] = er32(RDT);
+ regs_buff[6] = er32(RDTR);
+
+ regs_buff[7] = er32(TCTL);
+ regs_buff[8] = er32(TDLEN);
+ regs_buff[9] = er32(TDH);
+ regs_buff[10] = er32(TDT);
+ regs_buff[11] = er32(TIDV);
+
+ regs_buff[12] = hw->phy_type; /* PHY type (IGP=1, M88=0) */
+ if (hw->phy_type == e1000_phy_igp) {
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT,
+ IGP01E1000_PHY_AGC_A);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_A &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[13] = (u32)phy_data; /* cable length */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT,
+ IGP01E1000_PHY_AGC_B);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_B &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[14] = (u32)phy_data; /* cable length */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT,
+ IGP01E1000_PHY_AGC_C);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_C &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[15] = (u32)phy_data; /* cable length */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT,
+ IGP01E1000_PHY_AGC_D);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_D &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[16] = (u32)phy_data; /* cable length */
+ regs_buff[17] = 0; /* extended 10bt distance (not needed) */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, 0x0);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[18] = (u32)phy_data; /* cable polarity */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT,
+ IGP01E1000_PHY_PCS_INIT_REG);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[19] = (u32)phy_data; /* cable polarity */
+ regs_buff[20] = 0; /* polarity correction enabled (always) */
+ regs_buff[22] = 0; /* phy receive errors (unavailable) */
+ regs_buff[23] = regs_buff[18]; /* mdix mode */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, 0x0);
+ } else {
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ regs_buff[13] = (u32)phy_data; /* cable length */
+ regs_buff[14] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ regs_buff[15] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ regs_buff[16] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ regs_buff[17] = (u32)phy_data; /* extended 10bt distance */
+ regs_buff[18] = regs_buff[13]; /* cable polarity */
+ regs_buff[19] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ regs_buff[20] = regs_buff[17]; /* polarity correction */
+ /* phy receive errors */
+ regs_buff[22] = adapter->phy_stats.receive_errors;
+ regs_buff[23] = regs_buff[13]; /* mdix mode */
+ }
+ regs_buff[21] = adapter->phy_stats.idle_errors; /* phy idle errors */
+ e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
+ regs_buff[24] = (u32)phy_data; /* phy local receiver status */
+ regs_buff[25] = regs_buff[24]; /* phy remote receiver status */
+ if (hw->mac_type >= e1000_82540 &&
+ hw->media_type == e1000_media_type_copper) {
+ regs_buff[26] = er32(MANC);
+ }
+}
+
+static int e1000_get_eeprom_len(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ return hw->eeprom.word_size * 2;
+}
+
+static int e1000_get_eeprom(struct net_device *netdev,
+ struct ethtool_eeprom *eeprom, u8 *bytes)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u16 *eeprom_buff;
+ int first_word, last_word;
+ int ret_val = 0;
+ u16 i;
+
+ if (eeprom->len == 0)
+ return -EINVAL;
+
+ eeprom->magic = hw->vendor_id | (hw->device_id << 16);
+
+ first_word = eeprom->offset >> 1;
+ last_word = (eeprom->offset + eeprom->len - 1) >> 1;
+
+ eeprom_buff = kmalloc(sizeof(u16) *
+ (last_word - first_word + 1), GFP_KERNEL);
+ if (!eeprom_buff)
+ return -ENOMEM;
+
+ if (hw->eeprom.type == e1000_eeprom_spi)
+ ret_val = e1000_read_eeprom(hw, first_word,
+ last_word - first_word + 1,
+ eeprom_buff);
+ else {
+ for (i = 0; i < last_word - first_word + 1; i++) {
+ ret_val = e1000_read_eeprom(hw, first_word + i, 1,
+ &eeprom_buff[i]);
+ if (ret_val)
+ break;
+ }
+ }
+
+ /* Device's eeprom is always little-endian, word addressable */
+ for (i = 0; i < last_word - first_word + 1; i++)
+ le16_to_cpus(&eeprom_buff[i]);
+
+ memcpy(bytes, (u8 *)eeprom_buff + (eeprom->offset & 1),
+ eeprom->len);
+ kfree(eeprom_buff);
+
+ return ret_val;
+}
+
+static int e1000_set_eeprom(struct net_device *netdev,
+ struct ethtool_eeprom *eeprom, u8 *bytes)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u16 *eeprom_buff;
+ void *ptr;
+ int max_len, first_word, last_word, ret_val = 0;
+ u16 i;
+
+ if (eeprom->len == 0)
+ return -EOPNOTSUPP;
+
+ if (eeprom->magic != (hw->vendor_id | (hw->device_id << 16)))
+ return -EFAULT;
+
+ max_len = hw->eeprom.word_size * 2;
+
+ first_word = eeprom->offset >> 1;
+ last_word = (eeprom->offset + eeprom->len - 1) >> 1;
+ eeprom_buff = kmalloc(max_len, GFP_KERNEL);
+ if (!eeprom_buff)
+ return -ENOMEM;
+
+ ptr = (void *)eeprom_buff;
+
+ if (eeprom->offset & 1) {
+ /* need read/modify/write of first changed EEPROM word */
+ /* only the second byte of the word is being modified */
+ ret_val = e1000_read_eeprom(hw, first_word, 1,
+ &eeprom_buff[0]);
+ ptr++;
+ }
+ if (((eeprom->offset + eeprom->len) & 1) && (ret_val == 0)) {
+ /* need read/modify/write of last changed EEPROM word */
+ /* only the first byte of the word is being modified */
+ ret_val = e1000_read_eeprom(hw, last_word, 1,
+ &eeprom_buff[last_word - first_word]);
+ }
+
+ /* Device's eeprom is always little-endian, word addressable */
+ for (i = 0; i < last_word - first_word + 1; i++)
+ le16_to_cpus(&eeprom_buff[i]);
+
+ memcpy(ptr, bytes, eeprom->len);
+
+ for (i = 0; i < last_word - first_word + 1; i++)
+ eeprom_buff[i] = cpu_to_le16(eeprom_buff[i]);
+
+ ret_val = e1000_write_eeprom(hw, first_word,
+ last_word - first_word + 1, eeprom_buff);
+
+ /* Update the checksum over the first part of the EEPROM if needed */
+ if ((ret_val == 0) && (first_word <= EEPROM_CHECKSUM_REG))
+ e1000_update_eeprom_checksum(hw);
+
+ kfree(eeprom_buff);
+ return ret_val;
+}
+
+static void e1000_get_drvinfo(struct net_device *netdev,
+ struct ethtool_drvinfo *drvinfo)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ char firmware_version[32];
+
+ strncpy(drvinfo->driver, e1000_driver_name, 32);
+ strncpy(drvinfo->version, e1000_driver_version, 32);
+
+ sprintf(firmware_version, "N/A");
+ strncpy(drvinfo->fw_version, firmware_version, 32);
+ strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32);
+ drvinfo->regdump_len = e1000_get_regs_len(netdev);
+ drvinfo->eedump_len = e1000_get_eeprom_len(netdev);
+}
+
+static void e1000_get_ringparam(struct net_device *netdev,
+ struct ethtool_ringparam *ring)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ e1000_mac_type mac_type = hw->mac_type;
+ struct e1000_tx_ring *txdr = adapter->tx_ring;
+ struct e1000_rx_ring *rxdr = adapter->rx_ring;
+
+ ring->rx_max_pending = (mac_type < e1000_82544) ? E1000_MAX_RXD :
+ E1000_MAX_82544_RXD;
+ ring->tx_max_pending = (mac_type < e1000_82544) ? E1000_MAX_TXD :
+ E1000_MAX_82544_TXD;
+ ring->rx_mini_max_pending = 0;
+ ring->rx_jumbo_max_pending = 0;
+ ring->rx_pending = rxdr->count;
+ ring->tx_pending = txdr->count;
+ ring->rx_mini_pending = 0;
+ ring->rx_jumbo_pending = 0;
+}
+
+static int e1000_set_ringparam(struct net_device *netdev,
+ struct ethtool_ringparam *ring)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ e1000_mac_type mac_type = hw->mac_type;
+ struct e1000_tx_ring *txdr, *tx_old;
+ struct e1000_rx_ring *rxdr, *rx_old;
+ int i, err;
+
+ if (adapter->ecdev)
+ return -EBUSY;
+
+ if ((ring->rx_mini_pending) || (ring->rx_jumbo_pending))
+ return -EINVAL;
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+
+ if (netif_running(adapter->netdev))
+ e1000_down(adapter);
+
+ tx_old = adapter->tx_ring;
+ rx_old = adapter->rx_ring;
+
+ err = -ENOMEM;
+ txdr = kcalloc(adapter->num_tx_queues, sizeof(struct e1000_tx_ring), GFP_KERNEL);
+ if (!txdr)
+ goto err_alloc_tx;
+
+ rxdr = kcalloc(adapter->num_rx_queues, sizeof(struct e1000_rx_ring), GFP_KERNEL);
+ if (!rxdr)
+ goto err_alloc_rx;
+
+ adapter->tx_ring = txdr;
+ adapter->rx_ring = rxdr;
+
+ rxdr->count = max(ring->rx_pending,(u32)E1000_MIN_RXD);
+ rxdr->count = min(rxdr->count,(u32)(mac_type < e1000_82544 ?
+ E1000_MAX_RXD : E1000_MAX_82544_RXD));
+ rxdr->count = ALIGN(rxdr->count, REQ_RX_DESCRIPTOR_MULTIPLE);
+
+ txdr->count = max(ring->tx_pending,(u32)E1000_MIN_TXD);
+ txdr->count = min(txdr->count,(u32)(mac_type < e1000_82544 ?
+ E1000_MAX_TXD : E1000_MAX_82544_TXD));
+ txdr->count = ALIGN(txdr->count, REQ_TX_DESCRIPTOR_MULTIPLE);
+
+ for (i = 0; i < adapter->num_tx_queues; i++)
+ txdr[i].count = txdr->count;
+ for (i = 0; i < adapter->num_rx_queues; i++)
+ rxdr[i].count = rxdr->count;
+
+ if (netif_running(adapter->netdev)) {
+ /* Try to get new resources before deleting old */
+ err = e1000_setup_all_rx_resources(adapter);
+ if (err)
+ goto err_setup_rx;
+ err = e1000_setup_all_tx_resources(adapter);
+ if (err)
+ goto err_setup_tx;
+
+ /* save the new, restore the old in order to free it,
+ * then restore the new back again */
+
+ adapter->rx_ring = rx_old;
+ adapter->tx_ring = tx_old;
+ e1000_free_all_rx_resources(adapter);
+ e1000_free_all_tx_resources(adapter);
+ kfree(tx_old);
+ kfree(rx_old);
+ adapter->rx_ring = rxdr;
+ adapter->tx_ring = txdr;
+ err = e1000_up(adapter);
+ if (err)
+ goto err_setup;
+ }
+
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+ return 0;
+err_setup_tx:
+ e1000_free_all_rx_resources(adapter);
+err_setup_rx:
+ adapter->rx_ring = rx_old;
+ adapter->tx_ring = tx_old;
+ kfree(rxdr);
+err_alloc_rx:
+ kfree(txdr);
+err_alloc_tx:
+ e1000_up(adapter);
+err_setup:
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+ return err;
+}
+
+static bool reg_pattern_test(struct e1000_adapter *adapter, u64 *data, int reg,
+ u32 mask, u32 write)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ static const u32 test[] =
+ {0x5A5A5A5A, 0xA5A5A5A5, 0x00000000, 0xFFFFFFFF};
+ u8 __iomem *address = hw->hw_addr + reg;
+ u32 read;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(test); i++) {
+ writel(write & test[i], address);
+ read = readl(address);
+ if (read != (write & test[i] & mask)) {
+ DPRINTK(DRV, ERR, "pattern test reg %04X failed: "
+ "got 0x%08X expected 0x%08X\n",
+ reg, read, (write & test[i] & mask));
+ *data = reg;
+ return true;
+ }
+ }
+ return false;
+}
+
+static bool reg_set_and_check(struct e1000_adapter *adapter, u64 *data, int reg,
+ u32 mask, u32 write)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u8 __iomem *address = hw->hw_addr + reg;
+ u32 read;
+
+ writel(write & mask, address);
+ read = readl(address);
+ if ((read & mask) != (write & mask)) {
+ DPRINTK(DRV, ERR, "set/check reg %04X test failed: "
+ "got 0x%08X expected 0x%08X\n",
+ reg, (read & mask), (write & mask));
+ *data = reg;
+ return true;
+ }
+ return false;
+}
+
+#define REG_PATTERN_TEST(reg, mask, write) \
+ do { \
+ if (reg_pattern_test(adapter, data, \
+ (hw->mac_type >= e1000_82543) \
+ ? E1000_##reg : E1000_82542_##reg, \
+ mask, write)) \
+ return 1; \
+ } while (0)
+
+#define REG_SET_AND_CHECK(reg, mask, write) \
+ do { \
+ if (reg_set_and_check(adapter, data, \
+ (hw->mac_type >= e1000_82543) \
+ ? E1000_##reg : E1000_82542_##reg, \
+ mask, write)) \
+ return 1; \
+ } while (0)
+
+static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
+{
+ u32 value, before, after;
+ u32 i, toggle;
+ struct e1000_hw *hw = &adapter->hw;
+
+ /* The status register is Read Only, so a write should fail.
+ * Some bits that get toggled are ignored.
+ */
+
+ /* there are several bits on newer hardware that are r/w */
+ toggle = 0xFFFFF833;
+
+ before = er32(STATUS);
+ value = (er32(STATUS) & toggle);
+ ew32(STATUS, toggle);
+ after = er32(STATUS) & toggle;
+ if (value != after) {
+ DPRINTK(DRV, ERR, "failed STATUS register test got: "
+ "0x%08X expected: 0x%08X\n", after, value);
+ *data = 1;
+ return 1;
+ }
+ /* restore previous status */
+ ew32(STATUS, before);
+
+ REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF);
+
+ REG_PATTERN_TEST(RDTR, 0x0000FFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(RDBAH, 0xFFFFFFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(RDLEN, 0x000FFF80, 0x000FFFFF);
+ REG_PATTERN_TEST(RDH, 0x0000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(RDT, 0x0000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(FCRTH, 0x0000FFF8, 0x0000FFF8);
+ REG_PATTERN_TEST(FCTTV, 0x0000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(TIPG, 0x3FFFFFFF, 0x3FFFFFFF);
+ REG_PATTERN_TEST(TDBAH, 0xFFFFFFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(TDLEN, 0x000FFF80, 0x000FFFFF);
+
+ REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x00000000);
+
+ before = 0x06DFB3FE;
+ REG_SET_AND_CHECK(RCTL, before, 0x003FFFFB);
+ REG_SET_AND_CHECK(TCTL, 0xFFFFFFFF, 0x00000000);
+
+ if (hw->mac_type >= e1000_82543) {
+
+ REG_SET_AND_CHECK(RCTL, before, 0xFFFFFFFF);
+ REG_PATTERN_TEST(RDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
+ REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(TDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
+ REG_PATTERN_TEST(TIDV, 0x0000FFFF, 0x0000FFFF);
+ value = E1000_RAR_ENTRIES;
+ for (i = 0; i < value; i++) {
+ REG_PATTERN_TEST(RA + (((i << 1) + 1) << 2), 0x8003FFFF,
+ 0xFFFFFFFF);
+ }
+
+ } else {
+
+ REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x01FFFFFF);
+ REG_PATTERN_TEST(RDBAL, 0xFFFFF000, 0xFFFFFFFF);
+ REG_PATTERN_TEST(TXCW, 0x0000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(TDBAL, 0xFFFFF000, 0xFFFFFFFF);
+
+ }
+
+ value = E1000_MC_TBL_SIZE;
+ for (i = 0; i < value; i++)
+ REG_PATTERN_TEST(MTA + (i << 2), 0xFFFFFFFF, 0xFFFFFFFF);
+
+ *data = 0;
+ return 0;
+}
+
+static int e1000_eeprom_test(struct e1000_adapter *adapter, u64 *data)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 temp;
+ u16 checksum = 0;
+ u16 i;
+
+ *data = 0;
+ /* Read and add up the contents of the EEPROM */
+ for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
+ if ((e1000_read_eeprom(hw, i, 1, &temp)) < 0) {
+ *data = 1;
+ break;
+ }
+ checksum += temp;
+ }
+
+ /* If Checksum is not Correct return error else test passed */
+ if ((checksum != (u16)EEPROM_SUM) && !(*data))
+ *data = 2;
+
+ return *data;
+}
+
+static irqreturn_t e1000_test_intr(int irq, void *data)
+{
+ struct net_device *netdev = (struct net_device *)data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ adapter->test_icr |= er32(ICR);
+
+ return IRQ_HANDLED;
+}
+
+static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data)
+{
+ struct net_device *netdev = adapter->netdev;
+ u32 mask, i = 0;
+ bool shared_int = true;
+ u32 irq = adapter->pdev->irq;
+ struct e1000_hw *hw = &adapter->hw;
+
+ *data = 0;
+
+ /* NOTE: we don't test MSI interrupts here, yet */
+ /* Hook up test interrupt handler just for this test */
+ if (!request_irq(irq, &e1000_test_intr, IRQF_PROBE_SHARED, netdev->name,
+ netdev))
+ shared_int = false;
+ else if (request_irq(irq, &e1000_test_intr, IRQF_SHARED,
+ netdev->name, netdev)) {
+ *data = 1;
+ return -1;
+ }
+ DPRINTK(HW, INFO, "testing %s interrupt\n",
+ (shared_int ? "shared" : "unshared"));
+
+ /* Disable all the interrupts */
+ ew32(IMC, 0xFFFFFFFF);
+ msleep(10);
+
+ /* Test each interrupt */
+ for (; i < 10; i++) {
+
+ /* Interrupt to test */
+ mask = 1 << i;
+
+ if (!shared_int) {
+ /* Disable the interrupt to be reported in
+ * the cause register and then force the same
+ * interrupt and see if one gets posted. If
+ * an interrupt was posted to the bus, the
+ * test failed.
+ */
+ adapter->test_icr = 0;
+ ew32(IMC, mask);
+ ew32(ICS, mask);
+ msleep(10);
+
+ if (adapter->test_icr & mask) {
+ *data = 3;
+ break;
+ }
+ }
+
+ /* Enable the interrupt to be reported in
+ * the cause register and then force the same
+ * interrupt and see if one gets posted. If
+ * an interrupt was not posted to the bus, the
+ * test failed.
+ */
+ adapter->test_icr = 0;
+ ew32(IMS, mask);
+ ew32(ICS, mask);
+ msleep(10);
+
+ if (!(adapter->test_icr & mask)) {
+ *data = 4;
+ break;
+ }
+
+ if (!shared_int) {
+ /* Disable the other interrupts to be reported in
+ * the cause register and then force the other
+ * interrupts and see if any get posted. If
+ * an interrupt was posted to the bus, the
+ * test failed.
+ */
+ adapter->test_icr = 0;
+ ew32(IMC, ~mask & 0x00007FFF);
+ ew32(ICS, ~mask & 0x00007FFF);
+ msleep(10);
+
+ if (adapter->test_icr) {
+ *data = 5;
+ break;
+ }
+ }
+ }
+
+ /* Disable all the interrupts */
+ ew32(IMC, 0xFFFFFFFF);
+ msleep(10);
+
+ /* Unhook test interrupt handler */
+ free_irq(irq, netdev);
+
+ return *data;
+}
+
+static void e1000_free_desc_rings(struct e1000_adapter *adapter)
+{
+ struct e1000_tx_ring *txdr = &adapter->test_tx_ring;
+ struct e1000_rx_ring *rxdr = &adapter->test_rx_ring;
+ struct pci_dev *pdev = adapter->pdev;
+ int i;
+
+ if (txdr->desc && txdr->buffer_info) {
+ for (i = 0; i < txdr->count; i++) {
+ if (txdr->buffer_info[i].dma)
+ pci_unmap_single(pdev, txdr->buffer_info[i].dma,
+ txdr->buffer_info[i].length,
+ PCI_DMA_TODEVICE);
+ if (txdr->buffer_info[i].skb)
+ dev_kfree_skb(txdr->buffer_info[i].skb);
+ }
+ }
+
+ if (rxdr->desc && rxdr->buffer_info) {
+ for (i = 0; i < rxdr->count; i++) {
+ if (rxdr->buffer_info[i].dma)
+ pci_unmap_single(pdev, rxdr->buffer_info[i].dma,
+ rxdr->buffer_info[i].length,
+ PCI_DMA_FROMDEVICE);
+ if (rxdr->buffer_info[i].skb)
+ dev_kfree_skb(rxdr->buffer_info[i].skb);
+ }
+ }
+
+ if (txdr->desc) {
+ pci_free_consistent(pdev, txdr->size, txdr->desc, txdr->dma);
+ txdr->desc = NULL;
+ }
+ if (rxdr->desc) {
+ pci_free_consistent(pdev, rxdr->size, rxdr->desc, rxdr->dma);
+ rxdr->desc = NULL;
+ }
+
+ kfree(txdr->buffer_info);
+ txdr->buffer_info = NULL;
+ kfree(rxdr->buffer_info);
+ rxdr->buffer_info = NULL;
+
+ return;
+}
+
+static int e1000_setup_desc_rings(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_tx_ring *txdr = &adapter->test_tx_ring;
+ struct e1000_rx_ring *rxdr = &adapter->test_rx_ring;
+ struct pci_dev *pdev = adapter->pdev;
+ u32 rctl;
+ int i, ret_val;
+
+ /* Setup Tx descriptor ring and Tx buffers */
+
+ if (!txdr->count)
+ txdr->count = E1000_DEFAULT_TXD;
+
+ txdr->buffer_info = kcalloc(txdr->count, sizeof(struct e1000_buffer),
+ GFP_KERNEL);
+ if (!txdr->buffer_info) {
+ ret_val = 1;
+ goto err_nomem;
+ }
+
+ txdr->size = txdr->count * sizeof(struct e1000_tx_desc);
+ txdr->size = ALIGN(txdr->size, 4096);
+ txdr->desc = pci_alloc_consistent(pdev, txdr->size, &txdr->dma);
+ if (!txdr->desc) {
+ ret_val = 2;
+ goto err_nomem;
+ }
+ memset(txdr->desc, 0, txdr->size);
+ txdr->next_to_use = txdr->next_to_clean = 0;
+
+ ew32(TDBAL, ((u64)txdr->dma & 0x00000000FFFFFFFF));
+ ew32(TDBAH, ((u64)txdr->dma >> 32));
+ ew32(TDLEN, txdr->count * sizeof(struct e1000_tx_desc));
+ ew32(TDH, 0);
+ ew32(TDT, 0);
+ ew32(TCTL, E1000_TCTL_PSP | E1000_TCTL_EN |
+ E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT |
+ E1000_FDX_COLLISION_DISTANCE << E1000_COLD_SHIFT);
+
+ for (i = 0; i < txdr->count; i++) {
+ struct e1000_tx_desc *tx_desc = E1000_TX_DESC(*txdr, i);
+ struct sk_buff *skb;
+ unsigned int size = 1024;
+
+ skb = alloc_skb(size, GFP_KERNEL);
+ if (!skb) {
+ ret_val = 3;
+ goto err_nomem;
+ }
+ skb_put(skb, size);
+ txdr->buffer_info[i].skb = skb;
+ txdr->buffer_info[i].length = skb->len;
+ txdr->buffer_info[i].dma =
+ pci_map_single(pdev, skb->data, skb->len,
+ PCI_DMA_TODEVICE);
+ tx_desc->buffer_addr = cpu_to_le64(txdr->buffer_info[i].dma);
+ tx_desc->lower.data = cpu_to_le32(skb->len);
+ tx_desc->lower.data |= cpu_to_le32(E1000_TXD_CMD_EOP |
+ E1000_TXD_CMD_IFCS |
+ E1000_TXD_CMD_RPS);
+ tx_desc->upper.data = 0;
+ }
+
+ /* Setup Rx descriptor ring and Rx buffers */
+
+ if (!rxdr->count)
+ rxdr->count = E1000_DEFAULT_RXD;
+
+ rxdr->buffer_info = kcalloc(rxdr->count, sizeof(struct e1000_buffer),
+ GFP_KERNEL);
+ if (!rxdr->buffer_info) {
+ ret_val = 4;
+ goto err_nomem;
+ }
+
+ rxdr->size = rxdr->count * sizeof(struct e1000_rx_desc);
+ rxdr->desc = pci_alloc_consistent(pdev, rxdr->size, &rxdr->dma);
+ if (!rxdr->desc) {
+ ret_val = 5;
+ goto err_nomem;
+ }
+ memset(rxdr->desc, 0, rxdr->size);
+ rxdr->next_to_use = rxdr->next_to_clean = 0;
+
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ ew32(RDBAL, ((u64)rxdr->dma & 0xFFFFFFFF));
+ ew32(RDBAH, ((u64)rxdr->dma >> 32));
+ ew32(RDLEN, rxdr->size);
+ ew32(RDH, 0);
+ ew32(RDT, 0);
+ rctl = E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_SZ_2048 |
+ E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
+ (hw->mc_filter_type << E1000_RCTL_MO_SHIFT);
+ ew32(RCTL, rctl);
+
+ for (i = 0; i < rxdr->count; i++) {
+ struct e1000_rx_desc *rx_desc = E1000_RX_DESC(*rxdr, i);
+ struct sk_buff *skb;
+
+ skb = alloc_skb(E1000_RXBUFFER_2048 + NET_IP_ALIGN, GFP_KERNEL);
+ if (!skb) {
+ ret_val = 6;
+ goto err_nomem;
+ }
+ skb_reserve(skb, NET_IP_ALIGN);
+ rxdr->buffer_info[i].skb = skb;
+ rxdr->buffer_info[i].length = E1000_RXBUFFER_2048;
+ rxdr->buffer_info[i].dma =
+ pci_map_single(pdev, skb->data, E1000_RXBUFFER_2048,
+ PCI_DMA_FROMDEVICE);
+ rx_desc->buffer_addr = cpu_to_le64(rxdr->buffer_info[i].dma);
+ memset(skb->data, 0x00, skb->len);
+ }
+
+ return 0;
+
+err_nomem:
+ e1000_free_desc_rings(adapter);
+ return ret_val;
+}
+
+static void e1000_phy_disable_receiver(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ /* Write out to PHY registers 29 and 30 to disable the Receiver. */
+ e1000_write_phy_reg(hw, 29, 0x001F);
+ e1000_write_phy_reg(hw, 30, 0x8FFC);
+ e1000_write_phy_reg(hw, 29, 0x001A);
+ e1000_write_phy_reg(hw, 30, 0x8FF0);
+}
+
+static void e1000_phy_reset_clk_and_crs(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 phy_reg;
+
+ /* Because we reset the PHY above, we need to re-force TX_CLK in the
+ * Extended PHY Specific Control Register to 25MHz clock. This
+ * value defaults back to a 2.5MHz clock when the PHY is reset.
+ */
+ e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_reg);
+ phy_reg |= M88E1000_EPSCR_TX_CLK_25;
+ e1000_write_phy_reg(hw,
+ M88E1000_EXT_PHY_SPEC_CTRL, phy_reg);
+
+ /* In addition, because of the s/w reset above, we need to enable
+ * CRS on TX. This must be set for both full and half duplex
+ * operation.
+ */
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_reg);
+ phy_reg |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+ e1000_write_phy_reg(hw,
+ M88E1000_PHY_SPEC_CTRL, phy_reg);
+}
+
+static int e1000_nonintegrated_phy_loopback(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl_reg;
+ u16 phy_reg;
+
+ /* Setup the Device Control Register for PHY loopback test. */
+
+ ctrl_reg = er32(CTRL);
+ ctrl_reg |= (E1000_CTRL_ILOS | /* Invert Loss-Of-Signal */
+ E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
+ E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
+ E1000_CTRL_SPD_1000 | /* Force Speed to 1000 */
+ E1000_CTRL_FD); /* Force Duplex to FULL */
+
+ ew32(CTRL, ctrl_reg);
+
+ /* Read the PHY Specific Control Register (0x10) */
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_reg);
+
+ /* Clear Auto-Crossover bits in PHY Specific Control Register
+ * (bits 6:5).
+ */
+ phy_reg &= ~M88E1000_PSCR_AUTO_X_MODE;
+ e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_reg);
+
+ /* Perform software reset on the PHY */
+ e1000_phy_reset(hw);
+
+ /* Have to setup TX_CLK and TX_CRS after software reset */
+ e1000_phy_reset_clk_and_crs(adapter);
+
+ e1000_write_phy_reg(hw, PHY_CTRL, 0x8100);
+
+ /* Wait for reset to complete. */
+ udelay(500);
+
+ /* Have to setup TX_CLK and TX_CRS after software reset */
+ e1000_phy_reset_clk_and_crs(adapter);
+
+ /* Write out to PHY registers 29 and 30 to disable the Receiver. */
+ e1000_phy_disable_receiver(adapter);
+
+ /* Set the loopback bit in the PHY control register. */
+ e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
+ phy_reg |= MII_CR_LOOPBACK;
+ e1000_write_phy_reg(hw, PHY_CTRL, phy_reg);
+
+ /* Setup TX_CLK and TX_CRS one more time. */
+ e1000_phy_reset_clk_and_crs(adapter);
+
+ /* Check Phy Configuration */
+ e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
+ if (phy_reg != 0x4100)
+ return 9;
+
+ e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_reg);
+ if (phy_reg != 0x0070)
+ return 10;
+
+ e1000_read_phy_reg(hw, 29, &phy_reg);
+ if (phy_reg != 0x001A)
+ return 11;
+
+ return 0;
+}
+
+static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl_reg = 0;
+ u32 stat_reg = 0;
+
+ hw->autoneg = false;
+
+ if (hw->phy_type == e1000_phy_m88) {
+ /* Auto-MDI/MDIX Off */
+ e1000_write_phy_reg(hw,
+ M88E1000_PHY_SPEC_CTRL, 0x0808);
+ /* reset to update Auto-MDI/MDIX */
+ e1000_write_phy_reg(hw, PHY_CTRL, 0x9140);
+ /* autoneg off */
+ e1000_write_phy_reg(hw, PHY_CTRL, 0x8140);
+ }
+
+ ctrl_reg = er32(CTRL);
+
+ /* force 1000, set loopback */
+ e1000_write_phy_reg(hw, PHY_CTRL, 0x4140);
+
+ /* Now set up the MAC to the same speed/duplex as the PHY. */
+ ctrl_reg = er32(CTRL);
+ ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
+ ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
+ E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
+ E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */
+ E1000_CTRL_FD); /* Force Duplex to FULL */
+
+ if (hw->media_type == e1000_media_type_copper &&
+ hw->phy_type == e1000_phy_m88)
+ ctrl_reg |= E1000_CTRL_ILOS; /* Invert Loss of Signal */
+ else {
+ /* Set the ILOS bit on the fiber Nic is half
+ * duplex link is detected. */
+ stat_reg = er32(STATUS);
+ if ((stat_reg & E1000_STATUS_FD) == 0)
+ ctrl_reg |= (E1000_CTRL_ILOS | E1000_CTRL_SLU);
+ }
+
+ ew32(CTRL, ctrl_reg);
+
+ /* Disable the receiver on the PHY so when a cable is plugged in, the
+ * PHY does not begin to autoneg when a cable is reconnected to the NIC.
+ */
+ if (hw->phy_type == e1000_phy_m88)
+ e1000_phy_disable_receiver(adapter);
+
+ udelay(500);
+
+ return 0;
+}
+
+static int e1000_set_phy_loopback(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 phy_reg = 0;
+ u16 count = 0;
+
+ switch (hw->mac_type) {
+ case e1000_82543:
+ if (hw->media_type == e1000_media_type_copper) {
+ /* Attempt to setup Loopback mode on Non-integrated PHY.
+ * Some PHY registers get corrupted at random, so
+ * attempt this 10 times.
+ */
+ while (e1000_nonintegrated_phy_loopback(adapter) &&
+ count++ < 10);
+ if (count < 11)
+ return 0;
+ }
+ break;
+
+ case e1000_82544:
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ return e1000_integrated_phy_loopback(adapter);
+ break;
+ default:
+ /* Default PHY loopback work is to read the MII
+ * control register and assert bit 14 (loopback mode).
+ */
+ e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
+ phy_reg |= MII_CR_LOOPBACK;
+ e1000_write_phy_reg(hw, PHY_CTRL, phy_reg);
+ return 0;
+ break;
+ }
+
+ return 8;
+}
+
+static int e1000_setup_loopback_test(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl;
+
+ if (hw->media_type == e1000_media_type_fiber ||
+ hw->media_type == e1000_media_type_internal_serdes) {
+ switch (hw->mac_type) {
+ case e1000_82545:
+ case e1000_82546:
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ return e1000_set_phy_loopback(adapter);
+ break;
+ default:
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_LBM_TCVR;
+ ew32(RCTL, rctl);
+ return 0;
+ }
+ } else if (hw->media_type == e1000_media_type_copper)
+ return e1000_set_phy_loopback(adapter);
+
+ return 7;
+}
+
+static void e1000_loopback_cleanup(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl;
+ u16 phy_reg;
+
+ rctl = er32(RCTL);
+ rctl &= ~(E1000_RCTL_LBM_TCVR | E1000_RCTL_LBM_MAC);
+ ew32(RCTL, rctl);
+
+ switch (hw->mac_type) {
+ case e1000_82545:
+ case e1000_82546:
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ default:
+ hw->autoneg = true;
+ e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
+ if (phy_reg & MII_CR_LOOPBACK) {
+ phy_reg &= ~MII_CR_LOOPBACK;
+ e1000_write_phy_reg(hw, PHY_CTRL, phy_reg);
+ e1000_phy_reset(hw);
+ }
+ break;
+ }
+}
+
+static void e1000_create_lbtest_frame(struct sk_buff *skb,
+ unsigned int frame_size)
+{
+ memset(skb->data, 0xFF, frame_size);
+ frame_size &= ~1;
+ memset(&skb->data[frame_size / 2], 0xAA, frame_size / 2 - 1);
+ memset(&skb->data[frame_size / 2 + 10], 0xBE, 1);
+ memset(&skb->data[frame_size / 2 + 12], 0xAF, 1);
+}
+
+static int e1000_check_lbtest_frame(struct sk_buff *skb,
+ unsigned int frame_size)
+{
+ frame_size &= ~1;
+ if (*(skb->data + 3) == 0xFF) {
+ if ((*(skb->data + frame_size / 2 + 10) == 0xBE) &&
+ (*(skb->data + frame_size / 2 + 12) == 0xAF)) {
+ return 0;
+ }
+ }
+ return 13;
+}
+
+static int e1000_run_loopback_test(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_tx_ring *txdr = &adapter->test_tx_ring;
+ struct e1000_rx_ring *rxdr = &adapter->test_rx_ring;
+ struct pci_dev *pdev = adapter->pdev;
+ int i, j, k, l, lc, good_cnt, ret_val=0;
+ unsigned long time;
+
+ ew32(RDT, rxdr->count - 1);
+
+ /* Calculate the loop count based on the largest descriptor ring
+ * The idea is to wrap the largest ring a number of times using 64
+ * send/receive pairs during each loop
+ */
+
+ if (rxdr->count <= txdr->count)
+ lc = ((txdr->count / 64) * 2) + 1;
+ else
+ lc = ((rxdr->count / 64) * 2) + 1;
+
+ k = l = 0;
+ for (j = 0; j <= lc; j++) { /* loop count loop */
+ for (i = 0; i < 64; i++) { /* send the packets */
+ e1000_create_lbtest_frame(txdr->buffer_info[i].skb,
+ 1024);
+ pci_dma_sync_single_for_device(pdev,
+ txdr->buffer_info[k].dma,
+ txdr->buffer_info[k].length,
+ PCI_DMA_TODEVICE);
+ if (unlikely(++k == txdr->count)) k = 0;
+ }
+ ew32(TDT, k);
+ msleep(200);
+ time = jiffies; /* set the start time for the receive */
+ good_cnt = 0;
+ do { /* receive the sent packets */
+ pci_dma_sync_single_for_cpu(pdev,
+ rxdr->buffer_info[l].dma,
+ rxdr->buffer_info[l].length,
+ PCI_DMA_FROMDEVICE);
+
+ ret_val = e1000_check_lbtest_frame(
+ rxdr->buffer_info[l].skb,
+ 1024);
+ if (!ret_val)
+ good_cnt++;
+ if (unlikely(++l == rxdr->count)) l = 0;
+ /* time + 20 msecs (200 msecs on 2.4) is more than
+ * enough time to complete the receives, if it's
+ * exceeded, break and error off
+ */
+ } while (good_cnt < 64 && jiffies < (time + 20));
+ if (good_cnt != 64) {
+ ret_val = 13; /* ret_val is the same as mis-compare */
+ break;
+ }
+ if (jiffies >= (time + 2)) {
+ ret_val = 14; /* error code for time out error */
+ break;
+ }
+ } /* end loop count loop */
+ return ret_val;
+}
+
+static int e1000_loopback_test(struct e1000_adapter *adapter, u64 *data)
+{
+ *data = e1000_setup_desc_rings(adapter);
+ if (*data)
+ goto out;
+ *data = e1000_setup_loopback_test(adapter);
+ if (*data)
+ goto err_loopback;
+ *data = e1000_run_loopback_test(adapter);
+ e1000_loopback_cleanup(adapter);
+
+err_loopback:
+ e1000_free_desc_rings(adapter);
+out:
+ return *data;
+}
+
+static int e1000_link_test(struct e1000_adapter *adapter, u64 *data)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ *data = 0;
+ if (hw->media_type == e1000_media_type_internal_serdes) {
+ int i = 0;
+ hw->serdes_has_link = false;
+
+ /* On some blade server designs, link establishment
+ * could take as long as 2-3 minutes */
+ do {
+ e1000_check_for_link(hw);
+ if (hw->serdes_has_link)
+ return *data;
+ msleep(20);
+ } while (i++ < 3750);
+
+ *data = 1;
+ } else {
+ e1000_check_for_link(hw);
+ if (hw->autoneg) /* if auto_neg is set wait for it */
+ msleep(4000);
+
+ if (!(er32(STATUS) & E1000_STATUS_LU)) {
+ *data = 1;
+ }
+ }
+ return *data;
+}
+
+static int e1000_get_sset_count(struct net_device *netdev, int sset)
+{
+ switch (sset) {
+ case ETH_SS_TEST:
+ return E1000_TEST_LEN;
+ case ETH_SS_STATS:
+ return E1000_STATS_LEN;
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static void e1000_diag_test(struct net_device *netdev,
+ struct ethtool_test *eth_test, u64 *data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ bool if_running;
+
+ if (adapter->ecdev)
+ return;
+
+ if_running = netif_running(netdev);
+
+ set_bit(__E1000_TESTING, &adapter->flags);
+ if (eth_test->flags == ETH_TEST_FL_OFFLINE) {
+ /* Offline tests */
+
+ /* save speed, duplex, autoneg settings */
+ u16 autoneg_advertised = hw->autoneg_advertised;
+ u8 forced_speed_duplex = hw->forced_speed_duplex;
+ u8 autoneg = hw->autoneg;
+
+ DPRINTK(HW, INFO, "offline testing starting\n");
+
+ /* Link test performed before hardware reset so autoneg doesn't
+ * interfere with test result */
+ if (e1000_link_test(adapter, &data[4]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ if (if_running)
+ /* indicate we're in test mode */
+ dev_close(netdev);
+ else
+ e1000_reset(adapter);
+
+ if (e1000_reg_test(adapter, &data[0]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ e1000_reset(adapter);
+ if (e1000_eeprom_test(adapter, &data[1]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ e1000_reset(adapter);
+ if (e1000_intr_test(adapter, &data[2]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ e1000_reset(adapter);
+ /* make sure the phy is powered up */
+ e1000_power_up_phy(adapter);
+ if (e1000_loopback_test(adapter, &data[3]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ /* restore speed, duplex, autoneg settings */
+ hw->autoneg_advertised = autoneg_advertised;
+ hw->forced_speed_duplex = forced_speed_duplex;
+ hw->autoneg = autoneg;
+
+ e1000_reset(adapter);
+ clear_bit(__E1000_TESTING, &adapter->flags);
+ if (if_running)
+ dev_open(netdev);
+ } else {
+ DPRINTK(HW, INFO, "online testing starting\n");
+ /* Online tests */
+ if (e1000_link_test(adapter, &data[4]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ /* Online tests aren't run; pass by default */
+ data[0] = 0;
+ data[1] = 0;
+ data[2] = 0;
+ data[3] = 0;
+
+ clear_bit(__E1000_TESTING, &adapter->flags);
+ }
+ msleep_interruptible(4 * 1000);
+}
+
+static int e1000_wol_exclusion(struct e1000_adapter *adapter,
+ struct ethtool_wolinfo *wol)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ int retval = 1; /* fail by default */
+
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82542:
+ case E1000_DEV_ID_82543GC_FIBER:
+ case E1000_DEV_ID_82543GC_COPPER:
+ case E1000_DEV_ID_82544EI_FIBER:
+ case E1000_DEV_ID_82546EB_QUAD_COPPER:
+ case E1000_DEV_ID_82545EM_FIBER:
+ case E1000_DEV_ID_82545EM_COPPER:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER:
+ case E1000_DEV_ID_82546GB_PCIE:
+ /* these don't support WoL at all */
+ wol->supported = 0;
+ break;
+ case E1000_DEV_ID_82546EB_FIBER:
+ case E1000_DEV_ID_82546GB_FIBER:
+ /* Wake events not supported on port B */
+ if (er32(STATUS) & E1000_STATUS_FUNC_1) {
+ wol->supported = 0;
+ break;
+ }
+ /* return success for non excluded adapter ports */
+ retval = 0;
+ break;
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ /* quad port adapters only support WoL on port A */
+ if (!adapter->quad_port_a) {
+ wol->supported = 0;
+ break;
+ }
+ /* return success for non excluded adapter ports */
+ retval = 0;
+ break;
+ default:
+ /* dual port cards only support WoL on port A from now on
+ * unless it was enabled in the eeprom for port B
+ * so exclude FUNC_1 ports from having WoL enabled */
+ if (er32(STATUS) & E1000_STATUS_FUNC_1 &&
+ !adapter->eeprom_wol) {
+ wol->supported = 0;
+ break;
+ }
+
+ retval = 0;
+ }
+
+ return retval;
+}
+
+static void e1000_get_wol(struct net_device *netdev,
+ struct ethtool_wolinfo *wol)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ wol->supported = WAKE_UCAST | WAKE_MCAST |
+ WAKE_BCAST | WAKE_MAGIC;
+ wol->wolopts = 0;
+
+ /* this function will set ->supported = 0 and return 1 if wol is not
+ * supported by this hardware */
+ if (e1000_wol_exclusion(adapter, wol) ||
+ !device_can_wakeup(&adapter->pdev->dev))
+ return;
+
+ /* apply any specific unsupported masks here */
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ /* KSP3 does not suppport UCAST wake-ups */
+ wol->supported &= ~WAKE_UCAST;
+
+ if (adapter->wol & E1000_WUFC_EX)
+ DPRINTK(DRV, ERR, "Interface does not support "
+ "directed (unicast) frame wake-up packets\n");
+ break;
+ default:
+ break;
+ }
+
+ if (adapter->wol & E1000_WUFC_EX)
+ wol->wolopts |= WAKE_UCAST;
+ if (adapter->wol & E1000_WUFC_MC)
+ wol->wolopts |= WAKE_MCAST;
+ if (adapter->wol & E1000_WUFC_BC)
+ wol->wolopts |= WAKE_BCAST;
+ if (adapter->wol & E1000_WUFC_MAG)
+ wol->wolopts |= WAKE_MAGIC;
+
+ return;
+}
+
+static int e1000_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE))
+ return -EOPNOTSUPP;
+
+ if (e1000_wol_exclusion(adapter, wol) ||
+ !device_can_wakeup(&adapter->pdev->dev))
+ return wol->wolopts ? -EOPNOTSUPP : 0;
+
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ if (wol->wolopts & WAKE_UCAST) {
+ DPRINTK(DRV, ERR, "Interface does not support "
+ "directed (unicast) frame wake-up packets\n");
+ return -EOPNOTSUPP;
+ }
+ break;
+ default:
+ break;
+ }
+
+ /* these settings will always override what we currently have */
+ adapter->wol = 0;
+
+ if (wol->wolopts & WAKE_UCAST)
+ adapter->wol |= E1000_WUFC_EX;
+ if (wol->wolopts & WAKE_MCAST)
+ adapter->wol |= E1000_WUFC_MC;
+ if (wol->wolopts & WAKE_BCAST)
+ adapter->wol |= E1000_WUFC_BC;
+ if (wol->wolopts & WAKE_MAGIC)
+ adapter->wol |= E1000_WUFC_MAG;
+
+ device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
+
+ return 0;
+}
+
+/* toggle LED 4 times per second = 2 "blinks" per second */
+#define E1000_ID_INTERVAL (HZ/4)
+
+/* bit defines for adapter->led_status */
+#define E1000_LED_ON 0
+
+static void e1000_led_blink_callback(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (test_and_change_bit(E1000_LED_ON, &adapter->led_status))
+ e1000_led_off(hw);
+ else
+ e1000_led_on(hw);
+
+ mod_timer(&adapter->blink_timer, jiffies + E1000_ID_INTERVAL);
+}
+
+static int e1000_phys_id(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (!data)
+ data = INT_MAX;
+
+ if (!adapter->blink_timer.function) {
+ init_timer(&adapter->blink_timer);
+ adapter->blink_timer.function = e1000_led_blink_callback;
+ adapter->blink_timer.data = (unsigned long)adapter;
+ }
+ e1000_setup_led(hw);
+ mod_timer(&adapter->blink_timer, jiffies);
+ msleep_interruptible(data * 1000);
+ del_timer_sync(&adapter->blink_timer);
+
+ e1000_led_off(hw);
+ clear_bit(E1000_LED_ON, &adapter->led_status);
+ e1000_cleanup_led(hw);
+
+ return 0;
+}
+
+static int e1000_get_coalesce(struct net_device *netdev,
+ struct ethtool_coalesce *ec)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (adapter->hw.mac_type < e1000_82545)
+ return -EOPNOTSUPP;
+
+ if (adapter->itr_setting <= 3)
+ ec->rx_coalesce_usecs = adapter->itr_setting;
+ else
+ ec->rx_coalesce_usecs = 1000000 / adapter->itr_setting;
+
+ return 0;
+}
+
+static int e1000_set_coalesce(struct net_device *netdev,
+ struct ethtool_coalesce *ec)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (hw->mac_type < e1000_82545)
+ return -EOPNOTSUPP;
+
+ if ((ec->rx_coalesce_usecs > E1000_MAX_ITR_USECS) ||
+ ((ec->rx_coalesce_usecs > 3) &&
+ (ec->rx_coalesce_usecs < E1000_MIN_ITR_USECS)) ||
+ (ec->rx_coalesce_usecs == 2))
+ return -EINVAL;
+
+ if (ec->rx_coalesce_usecs <= 3) {
+ adapter->itr = 20000;
+ adapter->itr_setting = ec->rx_coalesce_usecs;
+ } else {
+ adapter->itr = (1000000 / ec->rx_coalesce_usecs);
+ adapter->itr_setting = adapter->itr & ~3;
+ }
+
+ if (adapter->itr_setting != 0)
+ ew32(ITR, 1000000000 / (adapter->itr * 256));
+ else
+ ew32(ITR, 0);
+
+ return 0;
+}
+
+static int e1000_nway_reset(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (adapter->ecdev)
+ return -EBUSY;
+
+ if (netif_running(netdev))
+ e1000_reinit_locked(adapter);
+ return 0;
+}
+
+static void e1000_get_ethtool_stats(struct net_device *netdev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ int i;
+
+ e1000_update_stats(adapter);
+ for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) {
+ char *p = (char *)adapter+e1000_gstrings_stats[i].stat_offset;
+ data[i] = (e1000_gstrings_stats[i].sizeof_stat ==
+ sizeof(u64)) ? *(u64 *)p : *(u32 *)p;
+ }
+/* BUG_ON(i != E1000_STATS_LEN); */
+}
+
+static void e1000_get_strings(struct net_device *netdev, u32 stringset,
+ u8 *data)
+{
+ u8 *p = data;
+ int i;
+
+ switch (stringset) {
+ case ETH_SS_TEST:
+ memcpy(data, *e1000_gstrings_test,
+ sizeof(e1000_gstrings_test));
+ break;
+ case ETH_SS_STATS:
+ for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) {
+ memcpy(p, e1000_gstrings_stats[i].stat_string,
+ ETH_GSTRING_LEN);
+ p += ETH_GSTRING_LEN;
+ }
+/* BUG_ON(p - data != E1000_STATS_LEN * ETH_GSTRING_LEN); */
+ break;
+ }
+}
+
+static const struct ethtool_ops e1000_ethtool_ops = {
+ .get_settings = e1000_get_settings,
+ .set_settings = e1000_set_settings,
+ .get_drvinfo = e1000_get_drvinfo,
+ .get_regs_len = e1000_get_regs_len,
+ .get_regs = e1000_get_regs,
+ .get_wol = e1000_get_wol,
+ .set_wol = e1000_set_wol,
+ .get_msglevel = e1000_get_msglevel,
+ .set_msglevel = e1000_set_msglevel,
+ .nway_reset = e1000_nway_reset,
+ .get_link = ethtool_op_get_link,
+ .get_eeprom_len = e1000_get_eeprom_len,
+ .get_eeprom = e1000_get_eeprom,
+ .set_eeprom = e1000_set_eeprom,
+ .get_ringparam = e1000_get_ringparam,
+ .set_ringparam = e1000_set_ringparam,
+ .get_pauseparam = e1000_get_pauseparam,
+ .set_pauseparam = e1000_set_pauseparam,
+ .get_rx_csum = e1000_get_rx_csum,
+ .set_rx_csum = e1000_set_rx_csum,
+ .get_tx_csum = e1000_get_tx_csum,
+ .set_tx_csum = e1000_set_tx_csum,
+ .set_sg = ethtool_op_set_sg,
+ .set_tso = e1000_set_tso,
+ .self_test = e1000_diag_test,
+ .get_strings = e1000_get_strings,
+ .phys_id = e1000_phys_id,
+ .get_ethtool_stats = e1000_get_ethtool_stats,
+ .get_sset_count = e1000_get_sset_count,
+ .get_coalesce = e1000_get_coalesce,
+ .set_coalesce = e1000_set_coalesce,
+};
+
+void e1000_set_ethtool_ops(struct net_device *netdev)
+{
+ SET_ETHTOOL_OPS(netdev, &e1000_ethtool_ops);
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_ethtool-2.6.32-orig.c Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,1902 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/* ethtool support for e1000 */
+
+#include "e1000.h"
+#include <asm/uaccess.h>
+
+struct e1000_stats {
+ char stat_string[ETH_GSTRING_LEN];
+ int sizeof_stat;
+ int stat_offset;
+};
+
+#define E1000_STAT(m) FIELD_SIZEOF(struct e1000_adapter, m), \
+ offsetof(struct e1000_adapter, m)
+static const struct e1000_stats e1000_gstrings_stats[] = {
+ { "rx_packets", E1000_STAT(stats.gprc) },
+ { "tx_packets", E1000_STAT(stats.gptc) },
+ { "rx_bytes", E1000_STAT(stats.gorcl) },
+ { "tx_bytes", E1000_STAT(stats.gotcl) },
+ { "rx_broadcast", E1000_STAT(stats.bprc) },
+ { "tx_broadcast", E1000_STAT(stats.bptc) },
+ { "rx_multicast", E1000_STAT(stats.mprc) },
+ { "tx_multicast", E1000_STAT(stats.mptc) },
+ { "rx_errors", E1000_STAT(stats.rxerrc) },
+ { "tx_errors", E1000_STAT(stats.txerrc) },
+ { "tx_dropped", E1000_STAT(net_stats.tx_dropped) },
+ { "multicast", E1000_STAT(stats.mprc) },
+ { "collisions", E1000_STAT(stats.colc) },
+ { "rx_length_errors", E1000_STAT(stats.rlerrc) },
+ { "rx_over_errors", E1000_STAT(net_stats.rx_over_errors) },
+ { "rx_crc_errors", E1000_STAT(stats.crcerrs) },
+ { "rx_frame_errors", E1000_STAT(net_stats.rx_frame_errors) },
+ { "rx_no_buffer_count", E1000_STAT(stats.rnbc) },
+ { "rx_missed_errors", E1000_STAT(stats.mpc) },
+ { "tx_aborted_errors", E1000_STAT(stats.ecol) },
+ { "tx_carrier_errors", E1000_STAT(stats.tncrs) },
+ { "tx_fifo_errors", E1000_STAT(net_stats.tx_fifo_errors) },
+ { "tx_heartbeat_errors", E1000_STAT(net_stats.tx_heartbeat_errors) },
+ { "tx_window_errors", E1000_STAT(stats.latecol) },
+ { "tx_abort_late_coll", E1000_STAT(stats.latecol) },
+ { "tx_deferred_ok", E1000_STAT(stats.dc) },
+ { "tx_single_coll_ok", E1000_STAT(stats.scc) },
+ { "tx_multi_coll_ok", E1000_STAT(stats.mcc) },
+ { "tx_timeout_count", E1000_STAT(tx_timeout_count) },
+ { "tx_restart_queue", E1000_STAT(restart_queue) },
+ { "rx_long_length_errors", E1000_STAT(stats.roc) },
+ { "rx_short_length_errors", E1000_STAT(stats.ruc) },
+ { "rx_align_errors", E1000_STAT(stats.algnerrc) },
+ { "tx_tcp_seg_good", E1000_STAT(stats.tsctc) },
+ { "tx_tcp_seg_failed", E1000_STAT(stats.tsctfc) },
+ { "rx_flow_control_xon", E1000_STAT(stats.xonrxc) },
+ { "rx_flow_control_xoff", E1000_STAT(stats.xoffrxc) },
+ { "tx_flow_control_xon", E1000_STAT(stats.xontxc) },
+ { "tx_flow_control_xoff", E1000_STAT(stats.xofftxc) },
+ { "rx_long_byte_count", E1000_STAT(stats.gorcl) },
+ { "rx_csum_offload_good", E1000_STAT(hw_csum_good) },
+ { "rx_csum_offload_errors", E1000_STAT(hw_csum_err) },
+ { "alloc_rx_buff_failed", E1000_STAT(alloc_rx_buff_failed) },
+ { "tx_smbus", E1000_STAT(stats.mgptc) },
+ { "rx_smbus", E1000_STAT(stats.mgprc) },
+ { "dropped_smbus", E1000_STAT(stats.mgpdc) },
+};
+
+#define E1000_QUEUE_STATS_LEN 0
+#define E1000_GLOBAL_STATS_LEN ARRAY_SIZE(e1000_gstrings_stats)
+#define E1000_STATS_LEN (E1000_GLOBAL_STATS_LEN + E1000_QUEUE_STATS_LEN)
+static const char e1000_gstrings_test[][ETH_GSTRING_LEN] = {
+ "Register test (offline)", "Eeprom test (offline)",
+ "Interrupt test (offline)", "Loopback test (offline)",
+ "Link test (on/offline)"
+};
+#define E1000_TEST_LEN ARRAY_SIZE(e1000_gstrings_test)
+
+static int e1000_get_settings(struct net_device *netdev,
+ struct ethtool_cmd *ecmd)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (hw->media_type == e1000_media_type_copper) {
+
+ ecmd->supported = (SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_1000baseT_Full|
+ SUPPORTED_Autoneg |
+ SUPPORTED_TP);
+ ecmd->advertising = ADVERTISED_TP;
+
+ if (hw->autoneg == 1) {
+ ecmd->advertising |= ADVERTISED_Autoneg;
+ /* the e1000 autoneg seems to match ethtool nicely */
+ ecmd->advertising |= hw->autoneg_advertised;
+ }
+
+ ecmd->port = PORT_TP;
+ ecmd->phy_address = hw->phy_addr;
+
+ if (hw->mac_type == e1000_82543)
+ ecmd->transceiver = XCVR_EXTERNAL;
+ else
+ ecmd->transceiver = XCVR_INTERNAL;
+
+ } else {
+ ecmd->supported = (SUPPORTED_1000baseT_Full |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Autoneg);
+
+ ecmd->advertising = (ADVERTISED_1000baseT_Full |
+ ADVERTISED_FIBRE |
+ ADVERTISED_Autoneg);
+
+ ecmd->port = PORT_FIBRE;
+
+ if (hw->mac_type >= e1000_82545)
+ ecmd->transceiver = XCVR_INTERNAL;
+ else
+ ecmd->transceiver = XCVR_EXTERNAL;
+ }
+
+ if (er32(STATUS) & E1000_STATUS_LU) {
+
+ e1000_get_speed_and_duplex(hw, &adapter->link_speed,
+ &adapter->link_duplex);
+ ecmd->speed = adapter->link_speed;
+
+ /* unfortunatly FULL_DUPLEX != DUPLEX_FULL
+ * and HALF_DUPLEX != DUPLEX_HALF */
+
+ if (adapter->link_duplex == FULL_DUPLEX)
+ ecmd->duplex = DUPLEX_FULL;
+ else
+ ecmd->duplex = DUPLEX_HALF;
+ } else {
+ ecmd->speed = -1;
+ ecmd->duplex = -1;
+ }
+
+ ecmd->autoneg = ((hw->media_type == e1000_media_type_fiber) ||
+ hw->autoneg) ? AUTONEG_ENABLE : AUTONEG_DISABLE;
+ return 0;
+}
+
+static int e1000_set_settings(struct net_device *netdev,
+ struct ethtool_cmd *ecmd)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+
+ if (ecmd->autoneg == AUTONEG_ENABLE) {
+ hw->autoneg = 1;
+ if (hw->media_type == e1000_media_type_fiber)
+ hw->autoneg_advertised = ADVERTISED_1000baseT_Full |
+ ADVERTISED_FIBRE |
+ ADVERTISED_Autoneg;
+ else
+ hw->autoneg_advertised = ecmd->advertising |
+ ADVERTISED_TP |
+ ADVERTISED_Autoneg;
+ ecmd->advertising = hw->autoneg_advertised;
+ } else
+ if (e1000_set_spd_dplx(adapter, ecmd->speed + ecmd->duplex)) {
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+ return -EINVAL;
+ }
+
+ /* reset the link */
+
+ if (netif_running(adapter->netdev)) {
+ e1000_down(adapter);
+ e1000_up(adapter);
+ } else
+ e1000_reset(adapter);
+
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+ return 0;
+}
+
+static void e1000_get_pauseparam(struct net_device *netdev,
+ struct ethtool_pauseparam *pause)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ pause->autoneg =
+ (adapter->fc_autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE);
+
+ if (hw->fc == E1000_FC_RX_PAUSE)
+ pause->rx_pause = 1;
+ else if (hw->fc == E1000_FC_TX_PAUSE)
+ pause->tx_pause = 1;
+ else if (hw->fc == E1000_FC_FULL) {
+ pause->rx_pause = 1;
+ pause->tx_pause = 1;
+ }
+}
+
+static int e1000_set_pauseparam(struct net_device *netdev,
+ struct ethtool_pauseparam *pause)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ int retval = 0;
+
+ adapter->fc_autoneg = pause->autoneg;
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+
+ if (pause->rx_pause && pause->tx_pause)
+ hw->fc = E1000_FC_FULL;
+ else if (pause->rx_pause && !pause->tx_pause)
+ hw->fc = E1000_FC_RX_PAUSE;
+ else if (!pause->rx_pause && pause->tx_pause)
+ hw->fc = E1000_FC_TX_PAUSE;
+ else if (!pause->rx_pause && !pause->tx_pause)
+ hw->fc = E1000_FC_NONE;
+
+ hw->original_fc = hw->fc;
+
+ if (adapter->fc_autoneg == AUTONEG_ENABLE) {
+ if (netif_running(adapter->netdev)) {
+ e1000_down(adapter);
+ e1000_up(adapter);
+ } else
+ e1000_reset(adapter);
+ } else
+ retval = ((hw->media_type == e1000_media_type_fiber) ?
+ e1000_setup_link(hw) : e1000_force_mac_fc(hw));
+
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+ return retval;
+}
+
+static u32 e1000_get_rx_csum(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ return adapter->rx_csum;
+}
+
+static int e1000_set_rx_csum(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ adapter->rx_csum = data;
+
+ if (netif_running(netdev))
+ e1000_reinit_locked(adapter);
+ else
+ e1000_reset(adapter);
+ return 0;
+}
+
+static u32 e1000_get_tx_csum(struct net_device *netdev)
+{
+ return (netdev->features & NETIF_F_HW_CSUM) != 0;
+}
+
+static int e1000_set_tx_csum(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (hw->mac_type < e1000_82543) {
+ if (!data)
+ return -EINVAL;
+ return 0;
+ }
+
+ if (data)
+ netdev->features |= NETIF_F_HW_CSUM;
+ else
+ netdev->features &= ~NETIF_F_HW_CSUM;
+
+ return 0;
+}
+
+static int e1000_set_tso(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if ((hw->mac_type < e1000_82544) ||
+ (hw->mac_type == e1000_82547))
+ return data ? -EINVAL : 0;
+
+ if (data)
+ netdev->features |= NETIF_F_TSO;
+ else
+ netdev->features &= ~NETIF_F_TSO;
+
+ netdev->features &= ~NETIF_F_TSO6;
+
+ DPRINTK(PROBE, INFO, "TSO is %s\n", data ? "Enabled" : "Disabled");
+ adapter->tso_force = true;
+ return 0;
+}
+
+static u32 e1000_get_msglevel(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ return adapter->msg_enable;
+}
+
+static void e1000_set_msglevel(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ adapter->msg_enable = data;
+}
+
+static int e1000_get_regs_len(struct net_device *netdev)
+{
+#define E1000_REGS_LEN 32
+ return E1000_REGS_LEN * sizeof(u32);
+}
+
+static void e1000_get_regs(struct net_device *netdev, struct ethtool_regs *regs,
+ void *p)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 *regs_buff = p;
+ u16 phy_data;
+
+ memset(p, 0, E1000_REGS_LEN * sizeof(u32));
+
+ regs->version = (1 << 24) | (hw->revision_id << 16) | hw->device_id;
+
+ regs_buff[0] = er32(CTRL);
+ regs_buff[1] = er32(STATUS);
+
+ regs_buff[2] = er32(RCTL);
+ regs_buff[3] = er32(RDLEN);
+ regs_buff[4] = er32(RDH);
+ regs_buff[5] = er32(RDT);
+ regs_buff[6] = er32(RDTR);
+
+ regs_buff[7] = er32(TCTL);
+ regs_buff[8] = er32(TDLEN);
+ regs_buff[9] = er32(TDH);
+ regs_buff[10] = er32(TDT);
+ regs_buff[11] = er32(TIDV);
+
+ regs_buff[12] = hw->phy_type; /* PHY type (IGP=1, M88=0) */
+ if (hw->phy_type == e1000_phy_igp) {
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT,
+ IGP01E1000_PHY_AGC_A);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_A &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[13] = (u32)phy_data; /* cable length */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT,
+ IGP01E1000_PHY_AGC_B);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_B &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[14] = (u32)phy_data; /* cable length */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT,
+ IGP01E1000_PHY_AGC_C);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_C &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[15] = (u32)phy_data; /* cable length */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT,
+ IGP01E1000_PHY_AGC_D);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_D &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[16] = (u32)phy_data; /* cable length */
+ regs_buff[17] = 0; /* extended 10bt distance (not needed) */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, 0x0);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[18] = (u32)phy_data; /* cable polarity */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT,
+ IGP01E1000_PHY_PCS_INIT_REG);
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG &
+ IGP01E1000_PHY_PAGE_SELECT, &phy_data);
+ regs_buff[19] = (u32)phy_data; /* cable polarity */
+ regs_buff[20] = 0; /* polarity correction enabled (always) */
+ regs_buff[22] = 0; /* phy receive errors (unavailable) */
+ regs_buff[23] = regs_buff[18]; /* mdix mode */
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, 0x0);
+ } else {
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ regs_buff[13] = (u32)phy_data; /* cable length */
+ regs_buff[14] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ regs_buff[15] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ regs_buff[16] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ regs_buff[17] = (u32)phy_data; /* extended 10bt distance */
+ regs_buff[18] = regs_buff[13]; /* cable polarity */
+ regs_buff[19] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ regs_buff[20] = regs_buff[17]; /* polarity correction */
+ /* phy receive errors */
+ regs_buff[22] = adapter->phy_stats.receive_errors;
+ regs_buff[23] = regs_buff[13]; /* mdix mode */
+ }
+ regs_buff[21] = adapter->phy_stats.idle_errors; /* phy idle errors */
+ e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
+ regs_buff[24] = (u32)phy_data; /* phy local receiver status */
+ regs_buff[25] = regs_buff[24]; /* phy remote receiver status */
+ if (hw->mac_type >= e1000_82540 &&
+ hw->media_type == e1000_media_type_copper) {
+ regs_buff[26] = er32(MANC);
+ }
+}
+
+static int e1000_get_eeprom_len(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ return hw->eeprom.word_size * 2;
+}
+
+static int e1000_get_eeprom(struct net_device *netdev,
+ struct ethtool_eeprom *eeprom, u8 *bytes)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u16 *eeprom_buff;
+ int first_word, last_word;
+ int ret_val = 0;
+ u16 i;
+
+ if (eeprom->len == 0)
+ return -EINVAL;
+
+ eeprom->magic = hw->vendor_id | (hw->device_id << 16);
+
+ first_word = eeprom->offset >> 1;
+ last_word = (eeprom->offset + eeprom->len - 1) >> 1;
+
+ eeprom_buff = kmalloc(sizeof(u16) *
+ (last_word - first_word + 1), GFP_KERNEL);
+ if (!eeprom_buff)
+ return -ENOMEM;
+
+ if (hw->eeprom.type == e1000_eeprom_spi)
+ ret_val = e1000_read_eeprom(hw, first_word,
+ last_word - first_word + 1,
+ eeprom_buff);
+ else {
+ for (i = 0; i < last_word - first_word + 1; i++) {
+ ret_val = e1000_read_eeprom(hw, first_word + i, 1,
+ &eeprom_buff[i]);
+ if (ret_val)
+ break;
+ }
+ }
+
+ /* Device's eeprom is always little-endian, word addressable */
+ for (i = 0; i < last_word - first_word + 1; i++)
+ le16_to_cpus(&eeprom_buff[i]);
+
+ memcpy(bytes, (u8 *)eeprom_buff + (eeprom->offset & 1),
+ eeprom->len);
+ kfree(eeprom_buff);
+
+ return ret_val;
+}
+
+static int e1000_set_eeprom(struct net_device *netdev,
+ struct ethtool_eeprom *eeprom, u8 *bytes)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u16 *eeprom_buff;
+ void *ptr;
+ int max_len, first_word, last_word, ret_val = 0;
+ u16 i;
+
+ if (eeprom->len == 0)
+ return -EOPNOTSUPP;
+
+ if (eeprom->magic != (hw->vendor_id | (hw->device_id << 16)))
+ return -EFAULT;
+
+ max_len = hw->eeprom.word_size * 2;
+
+ first_word = eeprom->offset >> 1;
+ last_word = (eeprom->offset + eeprom->len - 1) >> 1;
+ eeprom_buff = kmalloc(max_len, GFP_KERNEL);
+ if (!eeprom_buff)
+ return -ENOMEM;
+
+ ptr = (void *)eeprom_buff;
+
+ if (eeprom->offset & 1) {
+ /* need read/modify/write of first changed EEPROM word */
+ /* only the second byte of the word is being modified */
+ ret_val = e1000_read_eeprom(hw, first_word, 1,
+ &eeprom_buff[0]);
+ ptr++;
+ }
+ if (((eeprom->offset + eeprom->len) & 1) && (ret_val == 0)) {
+ /* need read/modify/write of last changed EEPROM word */
+ /* only the first byte of the word is being modified */
+ ret_val = e1000_read_eeprom(hw, last_word, 1,
+ &eeprom_buff[last_word - first_word]);
+ }
+
+ /* Device's eeprom is always little-endian, word addressable */
+ for (i = 0; i < last_word - first_word + 1; i++)
+ le16_to_cpus(&eeprom_buff[i]);
+
+ memcpy(ptr, bytes, eeprom->len);
+
+ for (i = 0; i < last_word - first_word + 1; i++)
+ eeprom_buff[i] = cpu_to_le16(eeprom_buff[i]);
+
+ ret_val = e1000_write_eeprom(hw, first_word,
+ last_word - first_word + 1, eeprom_buff);
+
+ /* Update the checksum over the first part of the EEPROM if needed */
+ if ((ret_val == 0) && (first_word <= EEPROM_CHECKSUM_REG))
+ e1000_update_eeprom_checksum(hw);
+
+ kfree(eeprom_buff);
+ return ret_val;
+}
+
+static void e1000_get_drvinfo(struct net_device *netdev,
+ struct ethtool_drvinfo *drvinfo)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ char firmware_version[32];
+
+ strncpy(drvinfo->driver, e1000_driver_name, 32);
+ strncpy(drvinfo->version, e1000_driver_version, 32);
+
+ sprintf(firmware_version, "N/A");
+ strncpy(drvinfo->fw_version, firmware_version, 32);
+ strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32);
+ drvinfo->regdump_len = e1000_get_regs_len(netdev);
+ drvinfo->eedump_len = e1000_get_eeprom_len(netdev);
+}
+
+static void e1000_get_ringparam(struct net_device *netdev,
+ struct ethtool_ringparam *ring)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ e1000_mac_type mac_type = hw->mac_type;
+ struct e1000_tx_ring *txdr = adapter->tx_ring;
+ struct e1000_rx_ring *rxdr = adapter->rx_ring;
+
+ ring->rx_max_pending = (mac_type < e1000_82544) ? E1000_MAX_RXD :
+ E1000_MAX_82544_RXD;
+ ring->tx_max_pending = (mac_type < e1000_82544) ? E1000_MAX_TXD :
+ E1000_MAX_82544_TXD;
+ ring->rx_mini_max_pending = 0;
+ ring->rx_jumbo_max_pending = 0;
+ ring->rx_pending = rxdr->count;
+ ring->tx_pending = txdr->count;
+ ring->rx_mini_pending = 0;
+ ring->rx_jumbo_pending = 0;
+}
+
+static int e1000_set_ringparam(struct net_device *netdev,
+ struct ethtool_ringparam *ring)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ e1000_mac_type mac_type = hw->mac_type;
+ struct e1000_tx_ring *txdr, *tx_old;
+ struct e1000_rx_ring *rxdr, *rx_old;
+ int i, err;
+
+ if ((ring->rx_mini_pending) || (ring->rx_jumbo_pending))
+ return -EINVAL;
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+
+ if (netif_running(adapter->netdev))
+ e1000_down(adapter);
+
+ tx_old = adapter->tx_ring;
+ rx_old = adapter->rx_ring;
+
+ err = -ENOMEM;
+ txdr = kcalloc(adapter->num_tx_queues, sizeof(struct e1000_tx_ring), GFP_KERNEL);
+ if (!txdr)
+ goto err_alloc_tx;
+
+ rxdr = kcalloc(adapter->num_rx_queues, sizeof(struct e1000_rx_ring), GFP_KERNEL);
+ if (!rxdr)
+ goto err_alloc_rx;
+
+ adapter->tx_ring = txdr;
+ adapter->rx_ring = rxdr;
+
+ rxdr->count = max(ring->rx_pending,(u32)E1000_MIN_RXD);
+ rxdr->count = min(rxdr->count,(u32)(mac_type < e1000_82544 ?
+ E1000_MAX_RXD : E1000_MAX_82544_RXD));
+ rxdr->count = ALIGN(rxdr->count, REQ_RX_DESCRIPTOR_MULTIPLE);
+
+ txdr->count = max(ring->tx_pending,(u32)E1000_MIN_TXD);
+ txdr->count = min(txdr->count,(u32)(mac_type < e1000_82544 ?
+ E1000_MAX_TXD : E1000_MAX_82544_TXD));
+ txdr->count = ALIGN(txdr->count, REQ_TX_DESCRIPTOR_MULTIPLE);
+
+ for (i = 0; i < adapter->num_tx_queues; i++)
+ txdr[i].count = txdr->count;
+ for (i = 0; i < adapter->num_rx_queues; i++)
+ rxdr[i].count = rxdr->count;
+
+ if (netif_running(adapter->netdev)) {
+ /* Try to get new resources before deleting old */
+ err = e1000_setup_all_rx_resources(adapter);
+ if (err)
+ goto err_setup_rx;
+ err = e1000_setup_all_tx_resources(adapter);
+ if (err)
+ goto err_setup_tx;
+
+ /* save the new, restore the old in order to free it,
+ * then restore the new back again */
+
+ adapter->rx_ring = rx_old;
+ adapter->tx_ring = tx_old;
+ e1000_free_all_rx_resources(adapter);
+ e1000_free_all_tx_resources(adapter);
+ kfree(tx_old);
+ kfree(rx_old);
+ adapter->rx_ring = rxdr;
+ adapter->tx_ring = txdr;
+ err = e1000_up(adapter);
+ if (err)
+ goto err_setup;
+ }
+
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+ return 0;
+err_setup_tx:
+ e1000_free_all_rx_resources(adapter);
+err_setup_rx:
+ adapter->rx_ring = rx_old;
+ adapter->tx_ring = tx_old;
+ kfree(rxdr);
+err_alloc_rx:
+ kfree(txdr);
+err_alloc_tx:
+ e1000_up(adapter);
+err_setup:
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+ return err;
+}
+
+static bool reg_pattern_test(struct e1000_adapter *adapter, u64 *data, int reg,
+ u32 mask, u32 write)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ static const u32 test[] =
+ {0x5A5A5A5A, 0xA5A5A5A5, 0x00000000, 0xFFFFFFFF};
+ u8 __iomem *address = hw->hw_addr + reg;
+ u32 read;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(test); i++) {
+ writel(write & test[i], address);
+ read = readl(address);
+ if (read != (write & test[i] & mask)) {
+ DPRINTK(DRV, ERR, "pattern test reg %04X failed: "
+ "got 0x%08X expected 0x%08X\n",
+ reg, read, (write & test[i] & mask));
+ *data = reg;
+ return true;
+ }
+ }
+ return false;
+}
+
+static bool reg_set_and_check(struct e1000_adapter *adapter, u64 *data, int reg,
+ u32 mask, u32 write)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u8 __iomem *address = hw->hw_addr + reg;
+ u32 read;
+
+ writel(write & mask, address);
+ read = readl(address);
+ if ((read & mask) != (write & mask)) {
+ DPRINTK(DRV, ERR, "set/check reg %04X test failed: "
+ "got 0x%08X expected 0x%08X\n",
+ reg, (read & mask), (write & mask));
+ *data = reg;
+ return true;
+ }
+ return false;
+}
+
+#define REG_PATTERN_TEST(reg, mask, write) \
+ do { \
+ if (reg_pattern_test(adapter, data, \
+ (hw->mac_type >= e1000_82543) \
+ ? E1000_##reg : E1000_82542_##reg, \
+ mask, write)) \
+ return 1; \
+ } while (0)
+
+#define REG_SET_AND_CHECK(reg, mask, write) \
+ do { \
+ if (reg_set_and_check(adapter, data, \
+ (hw->mac_type >= e1000_82543) \
+ ? E1000_##reg : E1000_82542_##reg, \
+ mask, write)) \
+ return 1; \
+ } while (0)
+
+static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
+{
+ u32 value, before, after;
+ u32 i, toggle;
+ struct e1000_hw *hw = &adapter->hw;
+
+ /* The status register is Read Only, so a write should fail.
+ * Some bits that get toggled are ignored.
+ */
+
+ /* there are several bits on newer hardware that are r/w */
+ toggle = 0xFFFFF833;
+
+ before = er32(STATUS);
+ value = (er32(STATUS) & toggle);
+ ew32(STATUS, toggle);
+ after = er32(STATUS) & toggle;
+ if (value != after) {
+ DPRINTK(DRV, ERR, "failed STATUS register test got: "
+ "0x%08X expected: 0x%08X\n", after, value);
+ *data = 1;
+ return 1;
+ }
+ /* restore previous status */
+ ew32(STATUS, before);
+
+ REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF);
+
+ REG_PATTERN_TEST(RDTR, 0x0000FFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(RDBAH, 0xFFFFFFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(RDLEN, 0x000FFF80, 0x000FFFFF);
+ REG_PATTERN_TEST(RDH, 0x0000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(RDT, 0x0000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(FCRTH, 0x0000FFF8, 0x0000FFF8);
+ REG_PATTERN_TEST(FCTTV, 0x0000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(TIPG, 0x3FFFFFFF, 0x3FFFFFFF);
+ REG_PATTERN_TEST(TDBAH, 0xFFFFFFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(TDLEN, 0x000FFF80, 0x000FFFFF);
+
+ REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x00000000);
+
+ before = 0x06DFB3FE;
+ REG_SET_AND_CHECK(RCTL, before, 0x003FFFFB);
+ REG_SET_AND_CHECK(TCTL, 0xFFFFFFFF, 0x00000000);
+
+ if (hw->mac_type >= e1000_82543) {
+
+ REG_SET_AND_CHECK(RCTL, before, 0xFFFFFFFF);
+ REG_PATTERN_TEST(RDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
+ REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(TDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
+ REG_PATTERN_TEST(TIDV, 0x0000FFFF, 0x0000FFFF);
+ value = E1000_RAR_ENTRIES;
+ for (i = 0; i < value; i++) {
+ REG_PATTERN_TEST(RA + (((i << 1) + 1) << 2), 0x8003FFFF,
+ 0xFFFFFFFF);
+ }
+
+ } else {
+
+ REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x01FFFFFF);
+ REG_PATTERN_TEST(RDBAL, 0xFFFFF000, 0xFFFFFFFF);
+ REG_PATTERN_TEST(TXCW, 0x0000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(TDBAL, 0xFFFFF000, 0xFFFFFFFF);
+
+ }
+
+ value = E1000_MC_TBL_SIZE;
+ for (i = 0; i < value; i++)
+ REG_PATTERN_TEST(MTA + (i << 2), 0xFFFFFFFF, 0xFFFFFFFF);
+
+ *data = 0;
+ return 0;
+}
+
+static int e1000_eeprom_test(struct e1000_adapter *adapter, u64 *data)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 temp;
+ u16 checksum = 0;
+ u16 i;
+
+ *data = 0;
+ /* Read and add up the contents of the EEPROM */
+ for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
+ if ((e1000_read_eeprom(hw, i, 1, &temp)) < 0) {
+ *data = 1;
+ break;
+ }
+ checksum += temp;
+ }
+
+ /* If Checksum is not Correct return error else test passed */
+ if ((checksum != (u16)EEPROM_SUM) && !(*data))
+ *data = 2;
+
+ return *data;
+}
+
+static irqreturn_t e1000_test_intr(int irq, void *data)
+{
+ struct net_device *netdev = (struct net_device *)data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ adapter->test_icr |= er32(ICR);
+
+ return IRQ_HANDLED;
+}
+
+static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data)
+{
+ struct net_device *netdev = adapter->netdev;
+ u32 mask, i = 0;
+ bool shared_int = true;
+ u32 irq = adapter->pdev->irq;
+ struct e1000_hw *hw = &adapter->hw;
+
+ *data = 0;
+
+ /* NOTE: we don't test MSI interrupts here, yet */
+ /* Hook up test interrupt handler just for this test */
+ if (!request_irq(irq, &e1000_test_intr, IRQF_PROBE_SHARED, netdev->name,
+ netdev))
+ shared_int = false;
+ else if (request_irq(irq, &e1000_test_intr, IRQF_SHARED,
+ netdev->name, netdev)) {
+ *data = 1;
+ return -1;
+ }
+ DPRINTK(HW, INFO, "testing %s interrupt\n",
+ (shared_int ? "shared" : "unshared"));
+
+ /* Disable all the interrupts */
+ ew32(IMC, 0xFFFFFFFF);
+ msleep(10);
+
+ /* Test each interrupt */
+ for (; i < 10; i++) {
+
+ /* Interrupt to test */
+ mask = 1 << i;
+
+ if (!shared_int) {
+ /* Disable the interrupt to be reported in
+ * the cause register and then force the same
+ * interrupt and see if one gets posted. If
+ * an interrupt was posted to the bus, the
+ * test failed.
+ */
+ adapter->test_icr = 0;
+ ew32(IMC, mask);
+ ew32(ICS, mask);
+ msleep(10);
+
+ if (adapter->test_icr & mask) {
+ *data = 3;
+ break;
+ }
+ }
+
+ /* Enable the interrupt to be reported in
+ * the cause register and then force the same
+ * interrupt and see if one gets posted. If
+ * an interrupt was not posted to the bus, the
+ * test failed.
+ */
+ adapter->test_icr = 0;
+ ew32(IMS, mask);
+ ew32(ICS, mask);
+ msleep(10);
+
+ if (!(adapter->test_icr & mask)) {
+ *data = 4;
+ break;
+ }
+
+ if (!shared_int) {
+ /* Disable the other interrupts to be reported in
+ * the cause register and then force the other
+ * interrupts and see if any get posted. If
+ * an interrupt was posted to the bus, the
+ * test failed.
+ */
+ adapter->test_icr = 0;
+ ew32(IMC, ~mask & 0x00007FFF);
+ ew32(ICS, ~mask & 0x00007FFF);
+ msleep(10);
+
+ if (adapter->test_icr) {
+ *data = 5;
+ break;
+ }
+ }
+ }
+
+ /* Disable all the interrupts */
+ ew32(IMC, 0xFFFFFFFF);
+ msleep(10);
+
+ /* Unhook test interrupt handler */
+ free_irq(irq, netdev);
+
+ return *data;
+}
+
+static void e1000_free_desc_rings(struct e1000_adapter *adapter)
+{
+ struct e1000_tx_ring *txdr = &adapter->test_tx_ring;
+ struct e1000_rx_ring *rxdr = &adapter->test_rx_ring;
+ struct pci_dev *pdev = adapter->pdev;
+ int i;
+
+ if (txdr->desc && txdr->buffer_info) {
+ for (i = 0; i < txdr->count; i++) {
+ if (txdr->buffer_info[i].dma)
+ pci_unmap_single(pdev, txdr->buffer_info[i].dma,
+ txdr->buffer_info[i].length,
+ PCI_DMA_TODEVICE);
+ if (txdr->buffer_info[i].skb)
+ dev_kfree_skb(txdr->buffer_info[i].skb);
+ }
+ }
+
+ if (rxdr->desc && rxdr->buffer_info) {
+ for (i = 0; i < rxdr->count; i++) {
+ if (rxdr->buffer_info[i].dma)
+ pci_unmap_single(pdev, rxdr->buffer_info[i].dma,
+ rxdr->buffer_info[i].length,
+ PCI_DMA_FROMDEVICE);
+ if (rxdr->buffer_info[i].skb)
+ dev_kfree_skb(rxdr->buffer_info[i].skb);
+ }
+ }
+
+ if (txdr->desc) {
+ pci_free_consistent(pdev, txdr->size, txdr->desc, txdr->dma);
+ txdr->desc = NULL;
+ }
+ if (rxdr->desc) {
+ pci_free_consistent(pdev, rxdr->size, rxdr->desc, rxdr->dma);
+ rxdr->desc = NULL;
+ }
+
+ kfree(txdr->buffer_info);
+ txdr->buffer_info = NULL;
+ kfree(rxdr->buffer_info);
+ rxdr->buffer_info = NULL;
+
+ return;
+}
+
+static int e1000_setup_desc_rings(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_tx_ring *txdr = &adapter->test_tx_ring;
+ struct e1000_rx_ring *rxdr = &adapter->test_rx_ring;
+ struct pci_dev *pdev = adapter->pdev;
+ u32 rctl;
+ int i, ret_val;
+
+ /* Setup Tx descriptor ring and Tx buffers */
+
+ if (!txdr->count)
+ txdr->count = E1000_DEFAULT_TXD;
+
+ txdr->buffer_info = kcalloc(txdr->count, sizeof(struct e1000_buffer),
+ GFP_KERNEL);
+ if (!txdr->buffer_info) {
+ ret_val = 1;
+ goto err_nomem;
+ }
+
+ txdr->size = txdr->count * sizeof(struct e1000_tx_desc);
+ txdr->size = ALIGN(txdr->size, 4096);
+ txdr->desc = pci_alloc_consistent(pdev, txdr->size, &txdr->dma);
+ if (!txdr->desc) {
+ ret_val = 2;
+ goto err_nomem;
+ }
+ memset(txdr->desc, 0, txdr->size);
+ txdr->next_to_use = txdr->next_to_clean = 0;
+
+ ew32(TDBAL, ((u64)txdr->dma & 0x00000000FFFFFFFF));
+ ew32(TDBAH, ((u64)txdr->dma >> 32));
+ ew32(TDLEN, txdr->count * sizeof(struct e1000_tx_desc));
+ ew32(TDH, 0);
+ ew32(TDT, 0);
+ ew32(TCTL, E1000_TCTL_PSP | E1000_TCTL_EN |
+ E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT |
+ E1000_FDX_COLLISION_DISTANCE << E1000_COLD_SHIFT);
+
+ for (i = 0; i < txdr->count; i++) {
+ struct e1000_tx_desc *tx_desc = E1000_TX_DESC(*txdr, i);
+ struct sk_buff *skb;
+ unsigned int size = 1024;
+
+ skb = alloc_skb(size, GFP_KERNEL);
+ if (!skb) {
+ ret_val = 3;
+ goto err_nomem;
+ }
+ skb_put(skb, size);
+ txdr->buffer_info[i].skb = skb;
+ txdr->buffer_info[i].length = skb->len;
+ txdr->buffer_info[i].dma =
+ pci_map_single(pdev, skb->data, skb->len,
+ PCI_DMA_TODEVICE);
+ tx_desc->buffer_addr = cpu_to_le64(txdr->buffer_info[i].dma);
+ tx_desc->lower.data = cpu_to_le32(skb->len);
+ tx_desc->lower.data |= cpu_to_le32(E1000_TXD_CMD_EOP |
+ E1000_TXD_CMD_IFCS |
+ E1000_TXD_CMD_RPS);
+ tx_desc->upper.data = 0;
+ }
+
+ /* Setup Rx descriptor ring and Rx buffers */
+
+ if (!rxdr->count)
+ rxdr->count = E1000_DEFAULT_RXD;
+
+ rxdr->buffer_info = kcalloc(rxdr->count, sizeof(struct e1000_buffer),
+ GFP_KERNEL);
+ if (!rxdr->buffer_info) {
+ ret_val = 4;
+ goto err_nomem;
+ }
+
+ rxdr->size = rxdr->count * sizeof(struct e1000_rx_desc);
+ rxdr->desc = pci_alloc_consistent(pdev, rxdr->size, &rxdr->dma);
+ if (!rxdr->desc) {
+ ret_val = 5;
+ goto err_nomem;
+ }
+ memset(rxdr->desc, 0, rxdr->size);
+ rxdr->next_to_use = rxdr->next_to_clean = 0;
+
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ ew32(RDBAL, ((u64)rxdr->dma & 0xFFFFFFFF));
+ ew32(RDBAH, ((u64)rxdr->dma >> 32));
+ ew32(RDLEN, rxdr->size);
+ ew32(RDH, 0);
+ ew32(RDT, 0);
+ rctl = E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_SZ_2048 |
+ E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
+ (hw->mc_filter_type << E1000_RCTL_MO_SHIFT);
+ ew32(RCTL, rctl);
+
+ for (i = 0; i < rxdr->count; i++) {
+ struct e1000_rx_desc *rx_desc = E1000_RX_DESC(*rxdr, i);
+ struct sk_buff *skb;
+
+ skb = alloc_skb(E1000_RXBUFFER_2048 + NET_IP_ALIGN, GFP_KERNEL);
+ if (!skb) {
+ ret_val = 6;
+ goto err_nomem;
+ }
+ skb_reserve(skb, NET_IP_ALIGN);
+ rxdr->buffer_info[i].skb = skb;
+ rxdr->buffer_info[i].length = E1000_RXBUFFER_2048;
+ rxdr->buffer_info[i].dma =
+ pci_map_single(pdev, skb->data, E1000_RXBUFFER_2048,
+ PCI_DMA_FROMDEVICE);
+ rx_desc->buffer_addr = cpu_to_le64(rxdr->buffer_info[i].dma);
+ memset(skb->data, 0x00, skb->len);
+ }
+
+ return 0;
+
+err_nomem:
+ e1000_free_desc_rings(adapter);
+ return ret_val;
+}
+
+static void e1000_phy_disable_receiver(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ /* Write out to PHY registers 29 and 30 to disable the Receiver. */
+ e1000_write_phy_reg(hw, 29, 0x001F);
+ e1000_write_phy_reg(hw, 30, 0x8FFC);
+ e1000_write_phy_reg(hw, 29, 0x001A);
+ e1000_write_phy_reg(hw, 30, 0x8FF0);
+}
+
+static void e1000_phy_reset_clk_and_crs(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 phy_reg;
+
+ /* Because we reset the PHY above, we need to re-force TX_CLK in the
+ * Extended PHY Specific Control Register to 25MHz clock. This
+ * value defaults back to a 2.5MHz clock when the PHY is reset.
+ */
+ e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_reg);
+ phy_reg |= M88E1000_EPSCR_TX_CLK_25;
+ e1000_write_phy_reg(hw,
+ M88E1000_EXT_PHY_SPEC_CTRL, phy_reg);
+
+ /* In addition, because of the s/w reset above, we need to enable
+ * CRS on TX. This must be set for both full and half duplex
+ * operation.
+ */
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_reg);
+ phy_reg |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+ e1000_write_phy_reg(hw,
+ M88E1000_PHY_SPEC_CTRL, phy_reg);
+}
+
+static int e1000_nonintegrated_phy_loopback(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl_reg;
+ u16 phy_reg;
+
+ /* Setup the Device Control Register for PHY loopback test. */
+
+ ctrl_reg = er32(CTRL);
+ ctrl_reg |= (E1000_CTRL_ILOS | /* Invert Loss-Of-Signal */
+ E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
+ E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
+ E1000_CTRL_SPD_1000 | /* Force Speed to 1000 */
+ E1000_CTRL_FD); /* Force Duplex to FULL */
+
+ ew32(CTRL, ctrl_reg);
+
+ /* Read the PHY Specific Control Register (0x10) */
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_reg);
+
+ /* Clear Auto-Crossover bits in PHY Specific Control Register
+ * (bits 6:5).
+ */
+ phy_reg &= ~M88E1000_PSCR_AUTO_X_MODE;
+ e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_reg);
+
+ /* Perform software reset on the PHY */
+ e1000_phy_reset(hw);
+
+ /* Have to setup TX_CLK and TX_CRS after software reset */
+ e1000_phy_reset_clk_and_crs(adapter);
+
+ e1000_write_phy_reg(hw, PHY_CTRL, 0x8100);
+
+ /* Wait for reset to complete. */
+ udelay(500);
+
+ /* Have to setup TX_CLK and TX_CRS after software reset */
+ e1000_phy_reset_clk_and_crs(adapter);
+
+ /* Write out to PHY registers 29 and 30 to disable the Receiver. */
+ e1000_phy_disable_receiver(adapter);
+
+ /* Set the loopback bit in the PHY control register. */
+ e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
+ phy_reg |= MII_CR_LOOPBACK;
+ e1000_write_phy_reg(hw, PHY_CTRL, phy_reg);
+
+ /* Setup TX_CLK and TX_CRS one more time. */
+ e1000_phy_reset_clk_and_crs(adapter);
+
+ /* Check Phy Configuration */
+ e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
+ if (phy_reg != 0x4100)
+ return 9;
+
+ e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_reg);
+ if (phy_reg != 0x0070)
+ return 10;
+
+ e1000_read_phy_reg(hw, 29, &phy_reg);
+ if (phy_reg != 0x001A)
+ return 11;
+
+ return 0;
+}
+
+static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl_reg = 0;
+ u32 stat_reg = 0;
+
+ hw->autoneg = false;
+
+ if (hw->phy_type == e1000_phy_m88) {
+ /* Auto-MDI/MDIX Off */
+ e1000_write_phy_reg(hw,
+ M88E1000_PHY_SPEC_CTRL, 0x0808);
+ /* reset to update Auto-MDI/MDIX */
+ e1000_write_phy_reg(hw, PHY_CTRL, 0x9140);
+ /* autoneg off */
+ e1000_write_phy_reg(hw, PHY_CTRL, 0x8140);
+ }
+
+ ctrl_reg = er32(CTRL);
+
+ /* force 1000, set loopback */
+ e1000_write_phy_reg(hw, PHY_CTRL, 0x4140);
+
+ /* Now set up the MAC to the same speed/duplex as the PHY. */
+ ctrl_reg = er32(CTRL);
+ ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
+ ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
+ E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
+ E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */
+ E1000_CTRL_FD); /* Force Duplex to FULL */
+
+ if (hw->media_type == e1000_media_type_copper &&
+ hw->phy_type == e1000_phy_m88)
+ ctrl_reg |= E1000_CTRL_ILOS; /* Invert Loss of Signal */
+ else {
+ /* Set the ILOS bit on the fiber Nic is half
+ * duplex link is detected. */
+ stat_reg = er32(STATUS);
+ if ((stat_reg & E1000_STATUS_FD) == 0)
+ ctrl_reg |= (E1000_CTRL_ILOS | E1000_CTRL_SLU);
+ }
+
+ ew32(CTRL, ctrl_reg);
+
+ /* Disable the receiver on the PHY so when a cable is plugged in, the
+ * PHY does not begin to autoneg when a cable is reconnected to the NIC.
+ */
+ if (hw->phy_type == e1000_phy_m88)
+ e1000_phy_disable_receiver(adapter);
+
+ udelay(500);
+
+ return 0;
+}
+
+static int e1000_set_phy_loopback(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 phy_reg = 0;
+ u16 count = 0;
+
+ switch (hw->mac_type) {
+ case e1000_82543:
+ if (hw->media_type == e1000_media_type_copper) {
+ /* Attempt to setup Loopback mode on Non-integrated PHY.
+ * Some PHY registers get corrupted at random, so
+ * attempt this 10 times.
+ */
+ while (e1000_nonintegrated_phy_loopback(adapter) &&
+ count++ < 10);
+ if (count < 11)
+ return 0;
+ }
+ break;
+
+ case e1000_82544:
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ return e1000_integrated_phy_loopback(adapter);
+ break;
+ default:
+ /* Default PHY loopback work is to read the MII
+ * control register and assert bit 14 (loopback mode).
+ */
+ e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
+ phy_reg |= MII_CR_LOOPBACK;
+ e1000_write_phy_reg(hw, PHY_CTRL, phy_reg);
+ return 0;
+ break;
+ }
+
+ return 8;
+}
+
+static int e1000_setup_loopback_test(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl;
+
+ if (hw->media_type == e1000_media_type_fiber ||
+ hw->media_type == e1000_media_type_internal_serdes) {
+ switch (hw->mac_type) {
+ case e1000_82545:
+ case e1000_82546:
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ return e1000_set_phy_loopback(adapter);
+ break;
+ default:
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_LBM_TCVR;
+ ew32(RCTL, rctl);
+ return 0;
+ }
+ } else if (hw->media_type == e1000_media_type_copper)
+ return e1000_set_phy_loopback(adapter);
+
+ return 7;
+}
+
+static void e1000_loopback_cleanup(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl;
+ u16 phy_reg;
+
+ rctl = er32(RCTL);
+ rctl &= ~(E1000_RCTL_LBM_TCVR | E1000_RCTL_LBM_MAC);
+ ew32(RCTL, rctl);
+
+ switch (hw->mac_type) {
+ case e1000_82545:
+ case e1000_82546:
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ default:
+ hw->autoneg = true;
+ e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
+ if (phy_reg & MII_CR_LOOPBACK) {
+ phy_reg &= ~MII_CR_LOOPBACK;
+ e1000_write_phy_reg(hw, PHY_CTRL, phy_reg);
+ e1000_phy_reset(hw);
+ }
+ break;
+ }
+}
+
+static void e1000_create_lbtest_frame(struct sk_buff *skb,
+ unsigned int frame_size)
+{
+ memset(skb->data, 0xFF, frame_size);
+ frame_size &= ~1;
+ memset(&skb->data[frame_size / 2], 0xAA, frame_size / 2 - 1);
+ memset(&skb->data[frame_size / 2 + 10], 0xBE, 1);
+ memset(&skb->data[frame_size / 2 + 12], 0xAF, 1);
+}
+
+static int e1000_check_lbtest_frame(struct sk_buff *skb,
+ unsigned int frame_size)
+{
+ frame_size &= ~1;
+ if (*(skb->data + 3) == 0xFF) {
+ if ((*(skb->data + frame_size / 2 + 10) == 0xBE) &&
+ (*(skb->data + frame_size / 2 + 12) == 0xAF)) {
+ return 0;
+ }
+ }
+ return 13;
+}
+
+static int e1000_run_loopback_test(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_tx_ring *txdr = &adapter->test_tx_ring;
+ struct e1000_rx_ring *rxdr = &adapter->test_rx_ring;
+ struct pci_dev *pdev = adapter->pdev;
+ int i, j, k, l, lc, good_cnt, ret_val=0;
+ unsigned long time;
+
+ ew32(RDT, rxdr->count - 1);
+
+ /* Calculate the loop count based on the largest descriptor ring
+ * The idea is to wrap the largest ring a number of times using 64
+ * send/receive pairs during each loop
+ */
+
+ if (rxdr->count <= txdr->count)
+ lc = ((txdr->count / 64) * 2) + 1;
+ else
+ lc = ((rxdr->count / 64) * 2) + 1;
+
+ k = l = 0;
+ for (j = 0; j <= lc; j++) { /* loop count loop */
+ for (i = 0; i < 64; i++) { /* send the packets */
+ e1000_create_lbtest_frame(txdr->buffer_info[i].skb,
+ 1024);
+ pci_dma_sync_single_for_device(pdev,
+ txdr->buffer_info[k].dma,
+ txdr->buffer_info[k].length,
+ PCI_DMA_TODEVICE);
+ if (unlikely(++k == txdr->count)) k = 0;
+ }
+ ew32(TDT, k);
+ msleep(200);
+ time = jiffies; /* set the start time for the receive */
+ good_cnt = 0;
+ do { /* receive the sent packets */
+ pci_dma_sync_single_for_cpu(pdev,
+ rxdr->buffer_info[l].dma,
+ rxdr->buffer_info[l].length,
+ PCI_DMA_FROMDEVICE);
+
+ ret_val = e1000_check_lbtest_frame(
+ rxdr->buffer_info[l].skb,
+ 1024);
+ if (!ret_val)
+ good_cnt++;
+ if (unlikely(++l == rxdr->count)) l = 0;
+ /* time + 20 msecs (200 msecs on 2.4) is more than
+ * enough time to complete the receives, if it's
+ * exceeded, break and error off
+ */
+ } while (good_cnt < 64 && jiffies < (time + 20));
+ if (good_cnt != 64) {
+ ret_val = 13; /* ret_val is the same as mis-compare */
+ break;
+ }
+ if (jiffies >= (time + 2)) {
+ ret_val = 14; /* error code for time out error */
+ break;
+ }
+ } /* end loop count loop */
+ return ret_val;
+}
+
+static int e1000_loopback_test(struct e1000_adapter *adapter, u64 *data)
+{
+ *data = e1000_setup_desc_rings(adapter);
+ if (*data)
+ goto out;
+ *data = e1000_setup_loopback_test(adapter);
+ if (*data)
+ goto err_loopback;
+ *data = e1000_run_loopback_test(adapter);
+ e1000_loopback_cleanup(adapter);
+
+err_loopback:
+ e1000_free_desc_rings(adapter);
+out:
+ return *data;
+}
+
+static int e1000_link_test(struct e1000_adapter *adapter, u64 *data)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ *data = 0;
+ if (hw->media_type == e1000_media_type_internal_serdes) {
+ int i = 0;
+ hw->serdes_has_link = false;
+
+ /* On some blade server designs, link establishment
+ * could take as long as 2-3 minutes */
+ do {
+ e1000_check_for_link(hw);
+ if (hw->serdes_has_link)
+ return *data;
+ msleep(20);
+ } while (i++ < 3750);
+
+ *data = 1;
+ } else {
+ e1000_check_for_link(hw);
+ if (hw->autoneg) /* if auto_neg is set wait for it */
+ msleep(4000);
+
+ if (!(er32(STATUS) & E1000_STATUS_LU)) {
+ *data = 1;
+ }
+ }
+ return *data;
+}
+
+static int e1000_get_sset_count(struct net_device *netdev, int sset)
+{
+ switch (sset) {
+ case ETH_SS_TEST:
+ return E1000_TEST_LEN;
+ case ETH_SS_STATS:
+ return E1000_STATS_LEN;
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static void e1000_diag_test(struct net_device *netdev,
+ struct ethtool_test *eth_test, u64 *data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ bool if_running = netif_running(netdev);
+
+ set_bit(__E1000_TESTING, &adapter->flags);
+ if (eth_test->flags == ETH_TEST_FL_OFFLINE) {
+ /* Offline tests */
+
+ /* save speed, duplex, autoneg settings */
+ u16 autoneg_advertised = hw->autoneg_advertised;
+ u8 forced_speed_duplex = hw->forced_speed_duplex;
+ u8 autoneg = hw->autoneg;
+
+ DPRINTK(HW, INFO, "offline testing starting\n");
+
+ /* Link test performed before hardware reset so autoneg doesn't
+ * interfere with test result */
+ if (e1000_link_test(adapter, &data[4]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ if (if_running)
+ /* indicate we're in test mode */
+ dev_close(netdev);
+ else
+ e1000_reset(adapter);
+
+ if (e1000_reg_test(adapter, &data[0]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ e1000_reset(adapter);
+ if (e1000_eeprom_test(adapter, &data[1]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ e1000_reset(adapter);
+ if (e1000_intr_test(adapter, &data[2]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ e1000_reset(adapter);
+ /* make sure the phy is powered up */
+ e1000_power_up_phy(adapter);
+ if (e1000_loopback_test(adapter, &data[3]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ /* restore speed, duplex, autoneg settings */
+ hw->autoneg_advertised = autoneg_advertised;
+ hw->forced_speed_duplex = forced_speed_duplex;
+ hw->autoneg = autoneg;
+
+ e1000_reset(adapter);
+ clear_bit(__E1000_TESTING, &adapter->flags);
+ if (if_running)
+ dev_open(netdev);
+ } else {
+ DPRINTK(HW, INFO, "online testing starting\n");
+ /* Online tests */
+ if (e1000_link_test(adapter, &data[4]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ /* Online tests aren't run; pass by default */
+ data[0] = 0;
+ data[1] = 0;
+ data[2] = 0;
+ data[3] = 0;
+
+ clear_bit(__E1000_TESTING, &adapter->flags);
+ }
+ msleep_interruptible(4 * 1000);
+}
+
+static int e1000_wol_exclusion(struct e1000_adapter *adapter,
+ struct ethtool_wolinfo *wol)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ int retval = 1; /* fail by default */
+
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82542:
+ case E1000_DEV_ID_82543GC_FIBER:
+ case E1000_DEV_ID_82543GC_COPPER:
+ case E1000_DEV_ID_82544EI_FIBER:
+ case E1000_DEV_ID_82546EB_QUAD_COPPER:
+ case E1000_DEV_ID_82545EM_FIBER:
+ case E1000_DEV_ID_82545EM_COPPER:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER:
+ case E1000_DEV_ID_82546GB_PCIE:
+ /* these don't support WoL at all */
+ wol->supported = 0;
+ break;
+ case E1000_DEV_ID_82546EB_FIBER:
+ case E1000_DEV_ID_82546GB_FIBER:
+ /* Wake events not supported on port B */
+ if (er32(STATUS) & E1000_STATUS_FUNC_1) {
+ wol->supported = 0;
+ break;
+ }
+ /* return success for non excluded adapter ports */
+ retval = 0;
+ break;
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ /* quad port adapters only support WoL on port A */
+ if (!adapter->quad_port_a) {
+ wol->supported = 0;
+ break;
+ }
+ /* return success for non excluded adapter ports */
+ retval = 0;
+ break;
+ default:
+ /* dual port cards only support WoL on port A from now on
+ * unless it was enabled in the eeprom for port B
+ * so exclude FUNC_1 ports from having WoL enabled */
+ if (er32(STATUS) & E1000_STATUS_FUNC_1 &&
+ !adapter->eeprom_wol) {
+ wol->supported = 0;
+ break;
+ }
+
+ retval = 0;
+ }
+
+ return retval;
+}
+
+static void e1000_get_wol(struct net_device *netdev,
+ struct ethtool_wolinfo *wol)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ wol->supported = WAKE_UCAST | WAKE_MCAST |
+ WAKE_BCAST | WAKE_MAGIC;
+ wol->wolopts = 0;
+
+ /* this function will set ->supported = 0 and return 1 if wol is not
+ * supported by this hardware */
+ if (e1000_wol_exclusion(adapter, wol) ||
+ !device_can_wakeup(&adapter->pdev->dev))
+ return;
+
+ /* apply any specific unsupported masks here */
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ /* KSP3 does not suppport UCAST wake-ups */
+ wol->supported &= ~WAKE_UCAST;
+
+ if (adapter->wol & E1000_WUFC_EX)
+ DPRINTK(DRV, ERR, "Interface does not support "
+ "directed (unicast) frame wake-up packets\n");
+ break;
+ default:
+ break;
+ }
+
+ if (adapter->wol & E1000_WUFC_EX)
+ wol->wolopts |= WAKE_UCAST;
+ if (adapter->wol & E1000_WUFC_MC)
+ wol->wolopts |= WAKE_MCAST;
+ if (adapter->wol & E1000_WUFC_BC)
+ wol->wolopts |= WAKE_BCAST;
+ if (adapter->wol & E1000_WUFC_MAG)
+ wol->wolopts |= WAKE_MAGIC;
+
+ return;
+}
+
+static int e1000_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE))
+ return -EOPNOTSUPP;
+
+ if (e1000_wol_exclusion(adapter, wol) ||
+ !device_can_wakeup(&adapter->pdev->dev))
+ return wol->wolopts ? -EOPNOTSUPP : 0;
+
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ if (wol->wolopts & WAKE_UCAST) {
+ DPRINTK(DRV, ERR, "Interface does not support "
+ "directed (unicast) frame wake-up packets\n");
+ return -EOPNOTSUPP;
+ }
+ break;
+ default:
+ break;
+ }
+
+ /* these settings will always override what we currently have */
+ adapter->wol = 0;
+
+ if (wol->wolopts & WAKE_UCAST)
+ adapter->wol |= E1000_WUFC_EX;
+ if (wol->wolopts & WAKE_MCAST)
+ adapter->wol |= E1000_WUFC_MC;
+ if (wol->wolopts & WAKE_BCAST)
+ adapter->wol |= E1000_WUFC_BC;
+ if (wol->wolopts & WAKE_MAGIC)
+ adapter->wol |= E1000_WUFC_MAG;
+
+ device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
+
+ return 0;
+}
+
+/* toggle LED 4 times per second = 2 "blinks" per second */
+#define E1000_ID_INTERVAL (HZ/4)
+
+/* bit defines for adapter->led_status */
+#define E1000_LED_ON 0
+
+static void e1000_led_blink_callback(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (test_and_change_bit(E1000_LED_ON, &adapter->led_status))
+ e1000_led_off(hw);
+ else
+ e1000_led_on(hw);
+
+ mod_timer(&adapter->blink_timer, jiffies + E1000_ID_INTERVAL);
+}
+
+static int e1000_phys_id(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (!data)
+ data = INT_MAX;
+
+ if (!adapter->blink_timer.function) {
+ init_timer(&adapter->blink_timer);
+ adapter->blink_timer.function = e1000_led_blink_callback;
+ adapter->blink_timer.data = (unsigned long)adapter;
+ }
+ e1000_setup_led(hw);
+ mod_timer(&adapter->blink_timer, jiffies);
+ msleep_interruptible(data * 1000);
+ del_timer_sync(&adapter->blink_timer);
+
+ e1000_led_off(hw);
+ clear_bit(E1000_LED_ON, &adapter->led_status);
+ e1000_cleanup_led(hw);
+
+ return 0;
+}
+
+static int e1000_get_coalesce(struct net_device *netdev,
+ struct ethtool_coalesce *ec)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (adapter->hw.mac_type < e1000_82545)
+ return -EOPNOTSUPP;
+
+ if (adapter->itr_setting <= 3)
+ ec->rx_coalesce_usecs = adapter->itr_setting;
+ else
+ ec->rx_coalesce_usecs = 1000000 / adapter->itr_setting;
+
+ return 0;
+}
+
+static int e1000_set_coalesce(struct net_device *netdev,
+ struct ethtool_coalesce *ec)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (hw->mac_type < e1000_82545)
+ return -EOPNOTSUPP;
+
+ if ((ec->rx_coalesce_usecs > E1000_MAX_ITR_USECS) ||
+ ((ec->rx_coalesce_usecs > 3) &&
+ (ec->rx_coalesce_usecs < E1000_MIN_ITR_USECS)) ||
+ (ec->rx_coalesce_usecs == 2))
+ return -EINVAL;
+
+ if (ec->rx_coalesce_usecs <= 3) {
+ adapter->itr = 20000;
+ adapter->itr_setting = ec->rx_coalesce_usecs;
+ } else {
+ adapter->itr = (1000000 / ec->rx_coalesce_usecs);
+ adapter->itr_setting = adapter->itr & ~3;
+ }
+
+ if (adapter->itr_setting != 0)
+ ew32(ITR, 1000000000 / (adapter->itr * 256));
+ else
+ ew32(ITR, 0);
+
+ return 0;
+}
+
+static int e1000_nway_reset(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ if (netif_running(netdev))
+ e1000_reinit_locked(adapter);
+ return 0;
+}
+
+static void e1000_get_ethtool_stats(struct net_device *netdev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ int i;
+
+ e1000_update_stats(adapter);
+ for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) {
+ char *p = (char *)adapter+e1000_gstrings_stats[i].stat_offset;
+ data[i] = (e1000_gstrings_stats[i].sizeof_stat ==
+ sizeof(u64)) ? *(u64 *)p : *(u32 *)p;
+ }
+/* BUG_ON(i != E1000_STATS_LEN); */
+}
+
+static void e1000_get_strings(struct net_device *netdev, u32 stringset,
+ u8 *data)
+{
+ u8 *p = data;
+ int i;
+
+ switch (stringset) {
+ case ETH_SS_TEST:
+ memcpy(data, *e1000_gstrings_test,
+ sizeof(e1000_gstrings_test));
+ break;
+ case ETH_SS_STATS:
+ for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) {
+ memcpy(p, e1000_gstrings_stats[i].stat_string,
+ ETH_GSTRING_LEN);
+ p += ETH_GSTRING_LEN;
+ }
+/* BUG_ON(p - data != E1000_STATS_LEN * ETH_GSTRING_LEN); */
+ break;
+ }
+}
+
+static const struct ethtool_ops e1000_ethtool_ops = {
+ .get_settings = e1000_get_settings,
+ .set_settings = e1000_set_settings,
+ .get_drvinfo = e1000_get_drvinfo,
+ .get_regs_len = e1000_get_regs_len,
+ .get_regs = e1000_get_regs,
+ .get_wol = e1000_get_wol,
+ .set_wol = e1000_set_wol,
+ .get_msglevel = e1000_get_msglevel,
+ .set_msglevel = e1000_set_msglevel,
+ .nway_reset = e1000_nway_reset,
+ .get_link = ethtool_op_get_link,
+ .get_eeprom_len = e1000_get_eeprom_len,
+ .get_eeprom = e1000_get_eeprom,
+ .set_eeprom = e1000_set_eeprom,
+ .get_ringparam = e1000_get_ringparam,
+ .set_ringparam = e1000_set_ringparam,
+ .get_pauseparam = e1000_get_pauseparam,
+ .set_pauseparam = e1000_set_pauseparam,
+ .get_rx_csum = e1000_get_rx_csum,
+ .set_rx_csum = e1000_set_rx_csum,
+ .get_tx_csum = e1000_get_tx_csum,
+ .set_tx_csum = e1000_set_tx_csum,
+ .set_sg = ethtool_op_set_sg,
+ .set_tso = e1000_set_tso,
+ .self_test = e1000_diag_test,
+ .get_strings = e1000_get_strings,
+ .phys_id = e1000_phys_id,
+ .get_ethtool_stats = e1000_get_ethtool_stats,
+ .get_sset_count = e1000_get_sset_count,
+ .get_coalesce = e1000_get_coalesce,
+ .set_coalesce = e1000_set_coalesce,
+};
+
+void e1000_set_ethtool_ops(struct net_device *netdev)
+{
+ SET_ETHTOOL_OPS(netdev, &e1000_ethtool_ops);
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_hw-2.6.32-ethercat.c Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,5634 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+ */
+
+/* e1000_hw.c
+ * Shared functions for accessing and configuring the MAC
+ */
+
+#include "e1000_hw-2.6.32-ethercat.h"
+
+static s32 e1000_check_downshift(struct e1000_hw *hw);
+static s32 e1000_check_polarity(struct e1000_hw *hw,
+ e1000_rev_polarity *polarity);
+static void e1000_clear_hw_cntrs(struct e1000_hw *hw);
+static void e1000_clear_vfta(struct e1000_hw *hw);
+static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw,
+ bool link_up);
+static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw);
+static s32 e1000_detect_gig_phy(struct e1000_hw *hw);
+static s32 e1000_get_auto_rd_done(struct e1000_hw *hw);
+static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length,
+ u16 *max_length);
+static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw);
+static s32 e1000_id_led_init(struct e1000_hw *hw);
+static void e1000_init_rx_addrs(struct e1000_hw *hw);
+static s32 e1000_phy_igp_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info);
+static s32 e1000_phy_m88_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info);
+static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active);
+static s32 e1000_wait_autoneg(struct e1000_hw *hw);
+static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value);
+static s32 e1000_set_phy_type(struct e1000_hw *hw);
+static void e1000_phy_init_script(struct e1000_hw *hw);
+static s32 e1000_setup_copper_link(struct e1000_hw *hw);
+static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw);
+static s32 e1000_adjust_serdes_amplitude(struct e1000_hw *hw);
+static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw);
+static s32 e1000_config_mac_to_phy(struct e1000_hw *hw);
+static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl);
+static void e1000_lower_mdi_clk(struct e1000_hw *hw, u32 *ctrl);
+static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count);
+static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw);
+static s32 e1000_phy_reset_dsp(struct e1000_hw *hw);
+static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data);
+static s32 e1000_write_eeprom_microwire(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data);
+static s32 e1000_spi_eeprom_ready(struct e1000_hw *hw);
+static void e1000_raise_ee_clk(struct e1000_hw *hw, u32 *eecd);
+static void e1000_lower_ee_clk(struct e1000_hw *hw, u32 *eecd);
+static void e1000_shift_out_ee_bits(struct e1000_hw *hw, u16 data, u16 count);
+static s32 e1000_write_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
+ u16 phy_data);
+static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
+ u16 *phy_data);
+static u16 e1000_shift_in_ee_bits(struct e1000_hw *hw, u16 count);
+static s32 e1000_acquire_eeprom(struct e1000_hw *hw);
+static void e1000_release_eeprom(struct e1000_hw *hw);
+static void e1000_standby_eeprom(struct e1000_hw *hw);
+static s32 e1000_set_vco_speed(struct e1000_hw *hw);
+static s32 e1000_polarity_reversal_workaround(struct e1000_hw *hw);
+static s32 e1000_set_phy_mode(struct e1000_hw *hw);
+static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data);
+static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data);
+
+/* IGP cable length table */
+static const
+u16 e1000_igp_cable_length_table[IGP01E1000_AGC_LENGTH_TABLE_SIZE] = {
+ 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+ 5, 10, 10, 10, 10, 10, 10, 10, 20, 20, 20, 20, 20, 25, 25, 25,
+ 25, 25, 25, 25, 30, 30, 30, 30, 40, 40, 40, 40, 40, 40, 40, 40,
+ 40, 50, 50, 50, 50, 50, 50, 50, 60, 60, 60, 60, 60, 60, 60, 60,
+ 60, 70, 70, 70, 70, 70, 70, 80, 80, 80, 80, 80, 80, 90, 90, 90,
+ 90, 90, 90, 90, 90, 90, 100, 100, 100, 100, 100, 100, 100, 100, 100,
+ 100,
+ 100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110,
+ 110, 110,
+ 110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120,
+ 120, 120
+};
+
+static DEFINE_SPINLOCK(e1000_eeprom_lock);
+
+/**
+ * e1000_set_phy_type - Set the phy type member in the hw struct.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static s32 e1000_set_phy_type(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_set_phy_type");
+
+ if (hw->mac_type == e1000_undefined)
+ return -E1000_ERR_PHY_TYPE;
+
+ switch (hw->phy_id) {
+ case M88E1000_E_PHY_ID:
+ case M88E1000_I_PHY_ID:
+ case M88E1011_I_PHY_ID:
+ case M88E1111_I_PHY_ID:
+ hw->phy_type = e1000_phy_m88;
+ break;
+ case IGP01E1000_I_PHY_ID:
+ if (hw->mac_type == e1000_82541 ||
+ hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ hw->phy_type = e1000_phy_igp;
+ break;
+ }
+ default:
+ /* Should never have loaded on this device */
+ hw->phy_type = e1000_phy_undefined;
+ return -E1000_ERR_PHY_TYPE;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_init_script - IGP phy init script - initializes the GbE PHY
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_phy_init_script(struct e1000_hw *hw)
+{
+ u32 ret_val;
+ u16 phy_saved_data;
+
+ DEBUGFUNC("e1000_phy_init_script");
+
+ if (hw->phy_init_script) {
+ msleep(20);
+
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of this routine. */
+ ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
+
+ /* Disabled the PHY transmitter */
+ e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
+ msleep(20);
+
+ e1000_write_phy_reg(hw, 0x0000, 0x0140);
+ msleep(5);
+
+ switch (hw->mac_type) {
+ case e1000_82541:
+ case e1000_82547:
+ e1000_write_phy_reg(hw, 0x1F95, 0x0001);
+ e1000_write_phy_reg(hw, 0x1F71, 0xBD21);
+ e1000_write_phy_reg(hw, 0x1F79, 0x0018);
+ e1000_write_phy_reg(hw, 0x1F30, 0x1600);
+ e1000_write_phy_reg(hw, 0x1F31, 0x0014);
+ e1000_write_phy_reg(hw, 0x1F32, 0x161C);
+ e1000_write_phy_reg(hw, 0x1F94, 0x0003);
+ e1000_write_phy_reg(hw, 0x1F96, 0x003F);
+ e1000_write_phy_reg(hw, 0x2010, 0x0008);
+ break;
+
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ e1000_write_phy_reg(hw, 0x1F73, 0x0099);
+ break;
+ default:
+ break;
+ }
+
+ e1000_write_phy_reg(hw, 0x0000, 0x3300);
+ msleep(20);
+
+ /* Now enable the transmitter */
+ e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
+
+ if (hw->mac_type == e1000_82547) {
+ u16 fused, fine, coarse;
+
+ /* Move to analog registers page */
+ e1000_read_phy_reg(hw,
+ IGP01E1000_ANALOG_SPARE_FUSE_STATUS,
+ &fused);
+
+ if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) {
+ e1000_read_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_STATUS,
+ &fused);
+
+ fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK;
+ coarse =
+ fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK;
+
+ if (coarse >
+ IGP01E1000_ANALOG_FUSE_COARSE_THRESH) {
+ coarse -=
+ IGP01E1000_ANALOG_FUSE_COARSE_10;
+ fine -= IGP01E1000_ANALOG_FUSE_FINE_1;
+ } else if (coarse ==
+ IGP01E1000_ANALOG_FUSE_COARSE_THRESH)
+ fine -= IGP01E1000_ANALOG_FUSE_FINE_10;
+
+ fused =
+ (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) |
+ (fine & IGP01E1000_ANALOG_FUSE_FINE_MASK) |
+ (coarse &
+ IGP01E1000_ANALOG_FUSE_COARSE_MASK);
+
+ e1000_write_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_CONTROL,
+ fused);
+ e1000_write_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_BYPASS,
+ IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL);
+ }
+ }
+ }
+}
+
+/**
+ * e1000_set_mac_type - Set the mac type member in the hw struct.
+ * @hw: Struct containing variables accessed by shared code
+ */
+s32 e1000_set_mac_type(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_set_mac_type");
+
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82542:
+ switch (hw->revision_id) {
+ case E1000_82542_2_0_REV_ID:
+ hw->mac_type = e1000_82542_rev2_0;
+ break;
+ case E1000_82542_2_1_REV_ID:
+ hw->mac_type = e1000_82542_rev2_1;
+ break;
+ default:
+ /* Invalid 82542 revision ID */
+ return -E1000_ERR_MAC_TYPE;
+ }
+ break;
+ case E1000_DEV_ID_82543GC_FIBER:
+ case E1000_DEV_ID_82543GC_COPPER:
+ hw->mac_type = e1000_82543;
+ break;
+ case E1000_DEV_ID_82544EI_COPPER:
+ case E1000_DEV_ID_82544EI_FIBER:
+ case E1000_DEV_ID_82544GC_COPPER:
+ case E1000_DEV_ID_82544GC_LOM:
+ hw->mac_type = e1000_82544;
+ break;
+ case E1000_DEV_ID_82540EM:
+ case E1000_DEV_ID_82540EM_LOM:
+ case E1000_DEV_ID_82540EP:
+ case E1000_DEV_ID_82540EP_LOM:
+ case E1000_DEV_ID_82540EP_LP:
+ hw->mac_type = e1000_82540;
+ break;
+ case E1000_DEV_ID_82545EM_COPPER:
+ case E1000_DEV_ID_82545EM_FIBER:
+ hw->mac_type = e1000_82545;
+ break;
+ case E1000_DEV_ID_82545GM_COPPER:
+ case E1000_DEV_ID_82545GM_FIBER:
+ case E1000_DEV_ID_82545GM_SERDES:
+ hw->mac_type = e1000_82545_rev_3;
+ break;
+ case E1000_DEV_ID_82546EB_COPPER:
+ case E1000_DEV_ID_82546EB_FIBER:
+ case E1000_DEV_ID_82546EB_QUAD_COPPER:
+ hw->mac_type = e1000_82546;
+ break;
+ case E1000_DEV_ID_82546GB_COPPER:
+ case E1000_DEV_ID_82546GB_FIBER:
+ case E1000_DEV_ID_82546GB_SERDES:
+ case E1000_DEV_ID_82546GB_PCIE:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ hw->mac_type = e1000_82546_rev_3;
+ break;
+ case E1000_DEV_ID_82541EI:
+ case E1000_DEV_ID_82541EI_MOBILE:
+ case E1000_DEV_ID_82541ER_LOM:
+ hw->mac_type = e1000_82541;
+ break;
+ case E1000_DEV_ID_82541ER:
+ case E1000_DEV_ID_82541GI:
+ case E1000_DEV_ID_82541GI_LF:
+ case E1000_DEV_ID_82541GI_MOBILE:
+ hw->mac_type = e1000_82541_rev_2;
+ break;
+ case E1000_DEV_ID_82547EI:
+ case E1000_DEV_ID_82547EI_MOBILE:
+ hw->mac_type = e1000_82547;
+ break;
+ case E1000_DEV_ID_82547GI:
+ hw->mac_type = e1000_82547_rev_2;
+ break;
+ default:
+ /* Should never have loaded on this device */
+ return -E1000_ERR_MAC_TYPE;
+ }
+
+ switch (hw->mac_type) {
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ hw->asf_firmware_present = true;
+ break;
+ default:
+ break;
+ }
+
+ /* The 82543 chip does not count tx_carrier_errors properly in
+ * FD mode
+ */
+ if (hw->mac_type == e1000_82543)
+ hw->bad_tx_carr_stats_fd = true;
+
+ if (hw->mac_type > e1000_82544)
+ hw->has_smbus = true;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_set_media_type - Set media type and TBI compatibility.
+ * @hw: Struct containing variables accessed by shared code
+ */
+void e1000_set_media_type(struct e1000_hw *hw)
+{
+ u32 status;
+
+ DEBUGFUNC("e1000_set_media_type");
+
+ if (hw->mac_type != e1000_82543) {
+ /* tbi_compatibility is only valid on 82543 */
+ hw->tbi_compatibility_en = false;
+ }
+
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82545GM_SERDES:
+ case E1000_DEV_ID_82546GB_SERDES:
+ hw->media_type = e1000_media_type_internal_serdes;
+ break;
+ default:
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ hw->media_type = e1000_media_type_fiber;
+ break;
+ default:
+ status = er32(STATUS);
+ if (status & E1000_STATUS_TBIMODE) {
+ hw->media_type = e1000_media_type_fiber;
+ /* tbi_compatibility not valid on fiber */
+ hw->tbi_compatibility_en = false;
+ } else {
+ hw->media_type = e1000_media_type_copper;
+ }
+ break;
+ }
+ }
+}
+
+/**
+ * e1000_reset_hw: reset the hardware completely
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Reset the transmit and receive units; mask and clear all interrupts.
+ */
+s32 e1000_reset_hw(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u32 ctrl_ext;
+ u32 icr;
+ u32 manc;
+ u32 led_ctrl;
+ s32 ret_val;
+
+ DEBUGFUNC("e1000_reset_hw");
+
+ /* For 82542 (rev 2.0), disable MWI before issuing a device reset */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
+ e1000_pci_clear_mwi(hw);
+ }
+
+ /* Clear interrupt mask to stop board from generating interrupts */
+ DEBUGOUT("Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ /* Disable the Transmit and Receive units. Then delay to allow
+ * any pending transactions to complete before we hit the MAC with
+ * the global reset.
+ */
+ ew32(RCTL, 0);
+ ew32(TCTL, E1000_TCTL_PSP);
+ E1000_WRITE_FLUSH();
+
+ /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */
+ hw->tbi_compatibility_on = false;
+
+ /* Delay to allow any outstanding PCI transactions to complete before
+ * resetting the device
+ */
+ msleep(10);
+
+ ctrl = er32(CTRL);
+
+ /* Must reset the PHY before resetting the MAC */
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ ew32(CTRL, (ctrl | E1000_CTRL_PHY_RST));
+ msleep(5);
+ }
+
+ /* Issue a global reset to the MAC. This will reset the chip's
+ * transmit, receive, DMA, and link units. It will not effect
+ * the current PCI configuration. The global reset bit is self-
+ * clearing, and should clear within a microsecond.
+ */
+ DEBUGOUT("Issuing a global reset to MAC\n");
+
+ switch (hw->mac_type) {
+ case e1000_82544:
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82546:
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ /* These controllers can't ack the 64-bit write when issuing the
+ * reset, so use IO-mapping as a workaround to issue the reset */
+ E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST));
+ break;
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ /* Reset is performed on a shadow of the control register */
+ ew32(CTRL_DUP, (ctrl | E1000_CTRL_RST));
+ break;
+ default:
+ ew32(CTRL, (ctrl | E1000_CTRL_RST));
+ break;
+ }
+
+ /* After MAC reset, force reload of EEPROM to restore power-on settings to
+ * device. Later controllers reload the EEPROM automatically, so just wait
+ * for reload to complete.
+ */
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ /* Wait for reset to complete */
+ udelay(10);
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+ ew32(CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH();
+ /* Wait for EEPROM reload */
+ msleep(2);
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ /* Wait for EEPROM reload */
+ msleep(20);
+ break;
+ default:
+ /* Auto read done will delay 5ms or poll based on mac type */
+ ret_val = e1000_get_auto_rd_done(hw);
+ if (ret_val)
+ return ret_val;
+ break;
+ }
+
+ /* Disable HW ARPs on ASF enabled adapters */
+ if (hw->mac_type >= e1000_82540) {
+ manc = er32(MANC);
+ manc &= ~(E1000_MANC_ARP_EN);
+ ew32(MANC, manc);
+ }
+
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ e1000_phy_init_script(hw);
+
+ /* Configure activity LED after PHY reset */
+ led_ctrl = er32(LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ ew32(LEDCTL, led_ctrl);
+ }
+
+ /* Clear interrupt mask to stop board from generating interrupts */
+ DEBUGOUT("Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ /* Clear any pending interrupt events. */
+ icr = er32(ICR);
+
+ /* If MWI was previously enabled, reenable it. */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE)
+ e1000_pci_set_mwi(hw);
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_init_hw: Performs basic configuration of the adapter.
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Assumes that the controller has previously been reset and is in a
+ * post-reset uninitialized state. Initializes the receive address registers,
+ * multicast table, and VLAN filter table. Calls routines to setup link
+ * configuration and flow control settings. Clears all on-chip counters. Leaves
+ * the transmit and receive units disabled and uninitialized.
+ */
+s32 e1000_init_hw(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u32 i;
+ s32 ret_val;
+ u32 mta_size;
+ u32 ctrl_ext;
+
+ DEBUGFUNC("e1000_init_hw");
+
+ /* Initialize Identification LED */
+ ret_val = e1000_id_led_init(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Initializing Identification LED\n");
+ return ret_val;
+ }
+
+ /* Set the media type and TBI compatibility */
+ e1000_set_media_type(hw);
+
+ /* Disabling VLAN filtering. */
+ DEBUGOUT("Initializing the IEEE VLAN\n");
+ if (hw->mac_type < e1000_82545_rev_3)
+ ew32(VET, 0);
+ e1000_clear_vfta(hw);
+
+ /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
+ e1000_pci_clear_mwi(hw);
+ ew32(RCTL, E1000_RCTL_RST);
+ E1000_WRITE_FLUSH();
+ msleep(5);
+ }
+
+ /* Setup the receive address. This involves initializing all of the Receive
+ * Address Registers (RARs 0 - 15).
+ */
+ e1000_init_rx_addrs(hw);
+
+ /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ ew32(RCTL, 0);
+ E1000_WRITE_FLUSH();
+ msleep(1);
+ if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE)
+ e1000_pci_set_mwi(hw);
+ }
+
+ /* Zero out the Multicast HASH table */
+ DEBUGOUT("Zeroing the MTA\n");
+ mta_size = E1000_MC_TBL_SIZE;
+ for (i = 0; i < mta_size; i++) {
+ E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
+ /* use write flush to prevent Memory Write Block (MWB) from
+ * occurring when accessing our register space */
+ E1000_WRITE_FLUSH();
+ }
+
+ /* Set the PCI priority bit correctly in the CTRL register. This
+ * determines if the adapter gives priority to receives, or if it
+ * gives equal priority to transmits and receives. Valid only on
+ * 82542 and 82543 silicon.
+ */
+ if (hw->dma_fairness && hw->mac_type <= e1000_82543) {
+ ctrl = er32(CTRL);
+ ew32(CTRL, ctrl | E1000_CTRL_PRIOR);
+ }
+
+ switch (hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
+ /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
+ if (hw->bus_type == e1000_bus_type_pcix
+ && e1000_pcix_get_mmrbc(hw) > 2048)
+ e1000_pcix_set_mmrbc(hw, 2048);
+ break;
+ }
+
+ /* Call a subroutine to configure the link and setup flow control. */
+ ret_val = e1000_setup_link(hw);
+
+ /* Set the transmit descriptor write-back policy */
+ if (hw->mac_type > e1000_82544) {
+ ctrl = er32(TXDCTL);
+ ctrl =
+ (ctrl & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB;
+ ew32(TXDCTL, ctrl);
+ }
+
+ /* Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ e1000_clear_hw_cntrs(hw);
+
+ if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
+ hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
+ ctrl_ext = er32(CTRL_EXT);
+ /* Relaxed ordering must be disabled to avoid a parity
+ * error crash in a PCI slot. */
+ ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
+ ew32(CTRL_EXT, ctrl_ext);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_adjust_serdes_amplitude - Adjust SERDES output amplitude based on EEPROM setting.
+ * @hw: Struct containing variables accessed by shared code.
+ */
+static s32 e1000_adjust_serdes_amplitude(struct e1000_hw *hw)
+{
+ u16 eeprom_data;
+ s32 ret_val;
+
+ DEBUGFUNC("e1000_adjust_serdes_amplitude");
+
+ if (hw->media_type != e1000_media_type_internal_serdes)
+ return E1000_SUCCESS;
+
+ switch (hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
+ return E1000_SUCCESS;
+ }
+
+ ret_val = e1000_read_eeprom(hw, EEPROM_SERDES_AMPLITUDE, 1,
+ &eeprom_data);
+ if (ret_val) {
+ return ret_val;
+ }
+
+ if (eeprom_data != EEPROM_RESERVED_WORD) {
+ /* Adjust SERDES output amplitude only. */
+ eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL, eeprom_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_setup_link - Configures flow control and link settings.
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Determines which flow control settings to use. Calls the appropriate media-
+ * specific link configuration function. Configures the flow control settings.
+ * Assuming the adapter has a valid link partner, a valid link should be
+ * established. Assumes the hardware has previously been reset and the
+ * transmitter and receiver are not enabled.
+ */
+s32 e1000_setup_link(struct e1000_hw *hw)
+{
+ u32 ctrl_ext;
+ s32 ret_val;
+ u16 eeprom_data;
+
+ DEBUGFUNC("e1000_setup_link");
+
+ /* Read and store word 0x0F of the EEPROM. This word contains bits
+ * that determine the hardware's default PAUSE (flow control) mode,
+ * a bit that determines whether the HW defaults to enabling or
+ * disabling auto-negotiation, and the direction of the
+ * SW defined pins. If there is no SW over-ride of the flow
+ * control setting, then the variable hw->fc will
+ * be initialized based on a value in the EEPROM.
+ */
+ if (hw->fc == E1000_FC_DEFAULT) {
+ ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+ 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
+ hw->fc = E1000_FC_NONE;
+ else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
+ EEPROM_WORD0F_ASM_DIR)
+ hw->fc = E1000_FC_TX_PAUSE;
+ else
+ hw->fc = E1000_FC_FULL;
+ }
+
+ /* We want to save off the original Flow Control configuration just
+ * in case we get disconnected and then reconnected into a different
+ * hub or switch with different Flow Control capabilities.
+ */
+ if (hw->mac_type == e1000_82542_rev2_0)
+ hw->fc &= (~E1000_FC_TX_PAUSE);
+
+ if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1))
+ hw->fc &= (~E1000_FC_RX_PAUSE);
+
+ hw->original_fc = hw->fc;
+
+ DEBUGOUT1("After fix-ups FlowControl is now = %x\n", hw->fc);
+
+ /* Take the 4 bits from EEPROM word 0x0F that determine the initial
+ * polarity value for the SW controlled pins, and setup the
+ * Extended Device Control reg with that info.
+ * This is needed because one of the SW controlled pins is used for
+ * signal detection. So this should be done before e1000_setup_pcs_link()
+ * or e1000_phy_setup() is called.
+ */
+ if (hw->mac_type == e1000_82543) {
+ ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+ 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) <<
+ SWDPIO__EXT_SHIFT);
+ ew32(CTRL_EXT, ctrl_ext);
+ }
+
+ /* Call the necessary subroutine to configure the link. */
+ ret_val = (hw->media_type == e1000_media_type_copper) ?
+ e1000_setup_copper_link(hw) : e1000_setup_fiber_serdes_link(hw);
+
+ /* Initialize the flow control address, type, and PAUSE timer
+ * registers to their default values. This is done even if flow
+ * control is disabled, because it does not hurt anything to
+ * initialize these registers.
+ */
+ DEBUGOUT
+ ("Initializing the Flow Control address, type and timer regs\n");
+
+ ew32(FCT, FLOW_CONTROL_TYPE);
+ ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+ ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW);
+
+ ew32(FCTTV, hw->fc_pause_time);
+
+ /* Set the flow control receive threshold registers. Normally,
+ * these registers will be set to a default threshold that may be
+ * adjusted later by the driver's runtime code. However, if the
+ * ability to transmit pause frames in not enabled, then these
+ * registers will be set to 0.
+ */
+ if (!(hw->fc & E1000_FC_TX_PAUSE)) {
+ ew32(FCRTL, 0);
+ ew32(FCRTH, 0);
+ } else {
+ /* We need to set up the Receive Threshold high and low water marks
+ * as well as (optionally) enabling the transmission of XON frames.
+ */
+ if (hw->fc_send_xon) {
+ ew32(FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE));
+ ew32(FCRTH, hw->fc_high_water);
+ } else {
+ ew32(FCRTL, hw->fc_low_water);
+ ew32(FCRTH, hw->fc_high_water);
+ }
+ }
+ return ret_val;
+}
+
+/**
+ * e1000_setup_fiber_serdes_link - prepare fiber or serdes link
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Manipulates Physical Coding Sublayer functions in order to configure
+ * link. Assumes the hardware has been previously reset and the transmitter
+ * and receiver are not enabled.
+ */
+static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u32 status;
+ u32 txcw = 0;
+ u32 i;
+ u32 signal = 0;
+ s32 ret_val;
+
+ DEBUGFUNC("e1000_setup_fiber_serdes_link");
+
+ /* On adapters with a MAC newer than 82544, SWDP 1 will be
+ * set when the optics detect a signal. On older adapters, it will be
+ * cleared when there is a signal. This applies to fiber media only.
+ * If we're on serdes media, adjust the output amplitude to value
+ * set in the EEPROM.
+ */
+ ctrl = er32(CTRL);
+ if (hw->media_type == e1000_media_type_fiber)
+ signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
+
+ ret_val = e1000_adjust_serdes_amplitude(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Take the link out of reset */
+ ctrl &= ~(E1000_CTRL_LRST);
+
+ /* Adjust VCO speed to improve BER performance */
+ ret_val = e1000_set_vco_speed(hw);
+ if (ret_val)
+ return ret_val;
+
+ e1000_config_collision_dist(hw);
+
+ /* Check for a software override of the flow control settings, and setup
+ * the device accordingly. If auto-negotiation is enabled, then software
+ * will have to set the "PAUSE" bits to the correct value in the Tranmsit
+ * Config Word Register (TXCW) and re-start auto-negotiation. However, if
+ * auto-negotiation is disabled, then software will have to manually
+ * configure the two flow control enable bits in the CTRL register.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames, but
+ * not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but we do
+ * not support receiving pause frames).
+ * 3: Both Rx and TX flow control (symmetric) are enabled.
+ */
+ switch (hw->fc) {
+ case E1000_FC_NONE:
+ /* Flow control is completely disabled by a software over-ride. */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
+ break;
+ case E1000_FC_RX_PAUSE:
+ /* RX Flow control is enabled and TX Flow control is disabled by a
+ * software over-ride. Since there really isn't a way to advertise
+ * that we are capable of RX Pause ONLY, we will advertise that we
+ * support both symmetric and asymmetric RX PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ case E1000_FC_TX_PAUSE:
+ /* TX Flow control is enabled, and RX Flow control is disabled, by a
+ * software over-ride.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
+ break;
+ case E1000_FC_FULL:
+ /* Flow control (both RX and TX) is enabled by a software over-ride. */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ default:
+ DEBUGOUT("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ break;
+ }
+
+ /* Since auto-negotiation is enabled, take the link out of reset (the link
+ * will be in reset, because we previously reset the chip). This will
+ * restart auto-negotiation. If auto-negotiation is successful then the
+ * link-up status bit will be set and the flow control enable bits (RFCE
+ * and TFCE) will be set according to their negotiated value.
+ */
+ DEBUGOUT("Auto-negotiation enabled\n");
+
+ ew32(TXCW, txcw);
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
+
+ hw->txcw = txcw;
+ msleep(1);
+
+ /* If we have a signal (the cable is plugged in) then poll for a "Link-Up"
+ * indication in the Device Status Register. Time-out if a link isn't
+ * seen in 500 milliseconds seconds (Auto-negotiation should complete in
+ * less than 500 milliseconds even if the other end is doing it in SW).
+ * For internal serdes, we just assume a signal is present, then poll.
+ */
+ if (hw->media_type == e1000_media_type_internal_serdes ||
+ (er32(CTRL) & E1000_CTRL_SWDPIN1) == signal) {
+ DEBUGOUT("Looking for Link\n");
+ for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) {
+ msleep(10);
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU)
+ break;
+ }
+ if (i == (LINK_UP_TIMEOUT / 10)) {
+ DEBUGOUT("Never got a valid link from auto-neg!!!\n");
+ hw->autoneg_failed = 1;
+ /* AutoNeg failed to achieve a link, so we'll call
+ * e1000_check_for_link. This routine will force the link up if
+ * we detect a signal. This will allow us to communicate with
+ * non-autonegotiating link partners.
+ */
+ ret_val = e1000_check_for_link(hw);
+ if (ret_val) {
+ DEBUGOUT("Error while checking for link\n");
+ return ret_val;
+ }
+ hw->autoneg_failed = 0;
+ } else {
+ hw->autoneg_failed = 0;
+ DEBUGOUT("Valid Link Found\n");
+ }
+ } else {
+ DEBUGOUT("No Signal Detected\n");
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_copper_link_preconfig - early configuration for copper
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Make sure we have a valid PHY and change PHY mode before link setup.
+ */
+static s32 e1000_copper_link_preconfig(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_copper_link_preconfig");
+
+ ctrl = er32(CTRL);
+ /* With 82543, we need to force speed and duplex on the MAC equal to what
+ * the PHY speed and duplex configuration is. In addition, we need to
+ * perform a hardware reset on the PHY to take it out of reset.
+ */
+ if (hw->mac_type > e1000_82543) {
+ ctrl |= E1000_CTRL_SLU;
+ ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ew32(CTRL, ctrl);
+ } else {
+ ctrl |=
+ (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
+ ew32(CTRL, ctrl);
+ ret_val = e1000_phy_hw_reset(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Make sure we have a valid PHY */
+ ret_val = e1000_detect_gig_phy(hw);
+ if (ret_val) {
+ DEBUGOUT("Error, did not detect valid phy.\n");
+ return ret_val;
+ }
+ DEBUGOUT1("Phy ID = %x \n", hw->phy_id);
+
+ /* Set PHY to class A mode (if necessary) */
+ ret_val = e1000_set_phy_mode(hw);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->mac_type == e1000_82545_rev_3) ||
+ (hw->mac_type == e1000_82546_rev_3)) {
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ phy_data |= 0x00000008;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ }
+
+ if (hw->mac_type <= e1000_82543 ||
+ hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
+ hw->mac_type == e1000_82541_rev_2
+ || hw->mac_type == e1000_82547_rev_2)
+ hw->phy_reset_disable = false;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_copper_link_igp_setup - Copper link setup for e1000_phy_igp series.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static s32 e1000_copper_link_igp_setup(struct e1000_hw *hw)
+{
+ u32 led_ctrl;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_copper_link_igp_setup");
+
+ if (hw->phy_reset_disable)
+ return E1000_SUCCESS;
+
+ ret_val = e1000_phy_reset(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
+
+ /* Wait 15ms for MAC to configure PHY from eeprom settings */
+ msleep(15);
+ /* Configure activity LED after PHY reset */
+ led_ctrl = er32(LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ ew32(LEDCTL, led_ctrl);
+
+ /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */
+ if (hw->phy_type == e1000_phy_igp) {
+ /* disable lplu d3 during driver init */
+ ret_val = e1000_set_d3_lplu_state(hw, false);
+ if (ret_val) {
+ DEBUGOUT("Error Disabling LPLU D3\n");
+ return ret_val;
+ }
+ }
+
+ /* Configure mdi-mdix settings */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ hw->dsp_config_state = e1000_dsp_config_disabled;
+ /* Force MDI for earlier revs of the IGP PHY */
+ phy_data &=
+ ~(IGP01E1000_PSCR_AUTO_MDIX |
+ IGP01E1000_PSCR_FORCE_MDI_MDIX);
+ hw->mdix = 1;
+
+ } else {
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+
+ switch (hw->mdix) {
+ case 1:
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 2:
+ phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 0:
+ default:
+ phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
+ break;
+ }
+ }
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* set auto-master slave resolution settings */
+ if (hw->autoneg) {
+ e1000_ms_type phy_ms_setting = hw->master_slave;
+
+ if (hw->ffe_config_state == e1000_ffe_config_active)
+ hw->ffe_config_state = e1000_ffe_config_enabled;
+
+ if (hw->dsp_config_state == e1000_dsp_config_activated)
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+
+ /* when autonegotiation advertisement is only 1000Mbps then we
+ * should disable SmartSpeed and enable Auto MasterSlave
+ * resolution as hardware default. */
+ if (hw->autoneg_advertised == ADVERTISE_1000_FULL) {
+ /* Disable SmartSpeed */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ /* Set auto Master/Slave resolution process */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_data &= ~CR_1000T_MS_ENABLE;
+ ret_val =
+ e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* load defaults for future use */
+ hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
+ ((phy_data & CR_1000T_MS_VALUE) ?
+ e1000_ms_force_master :
+ e1000_ms_force_slave) : e1000_ms_auto;
+
+ switch (phy_ms_setting) {
+ case e1000_ms_force_master:
+ phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_force_slave:
+ phy_data |= CR_1000T_MS_ENABLE;
+ phy_data &= ~(CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_auto:
+ phy_data &= ~CR_1000T_MS_ENABLE;
+ default:
+ break;
+ }
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_copper_link_mgp_setup - Copper link setup for e1000_phy_m88 series.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static s32 e1000_copper_link_mgp_setup(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_copper_link_mgp_setup");
+
+ if (hw->phy_reset_disable)
+ return E1000_SUCCESS;
+
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+
+ /* Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+
+ switch (hw->mdix) {
+ case 1:
+ phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
+ break;
+ case 2:
+ phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
+ break;
+ case 3:
+ phy_data |= M88E1000_PSCR_AUTO_X_1000T;
+ break;
+ case 0:
+ default:
+ phy_data |= M88E1000_PSCR_AUTO_X_MODE;
+ break;
+ }
+
+ /* Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
+ if (hw->disable_polarity_correction == 1)
+ phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (hw->phy_revision < M88E1011_I_REV_4) {
+ /* Force TX_CLK in the Extended PHY Specific Control Register
+ * to 25MHz clock.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+
+ if ((hw->phy_revision == E1000_REVISION_2) &&
+ (hw->phy_id == M88E1111_I_PHY_ID)) {
+ /* Vidalia Phy, set the downshift counter to 5x */
+ phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK);
+ phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X;
+ ret_val = e1000_write_phy_reg(hw,
+ M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ } else {
+ /* Configure Master and Slave downshift values */
+ phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
+ phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
+ ret_val = e1000_write_phy_reg(hw,
+ M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+
+ /* SW Reset the PHY so all changes take effect */
+ ret_val = e1000_phy_reset(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_copper_link_autoneg - setup auto-neg
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Setup auto-negotiation and flow control advertisements,
+ * and then perform auto-negotiation.
+ */
+static s32 e1000_copper_link_autoneg(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_copper_link_autoneg");
+
+ /* Perform some bounds checking on the hw->autoneg_advertised
+ * parameter. If this variable is zero, then set it to the default.
+ */
+ hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;
+
+ /* If autoneg_advertised is zero, we assume it was not defaulted
+ * by the calling code so we set to advertise full capability.
+ */
+ if (hw->autoneg_advertised == 0)
+ hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+
+ DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
+ ret_val = e1000_phy_setup_autoneg(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Setting up Auto-Negotiation\n");
+ return ret_val;
+ }
+ DEBUGOUT("Restarting Auto-Neg\n");
+
+ /* Restart auto-negotiation by setting the Auto Neg Enable bit and
+ * the Auto Neg Restart bit in the PHY control register.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Does the user want to wait for Auto-Neg to complete here, or
+ * check at a later time (for example, callback routine).
+ */
+ if (hw->wait_autoneg_complete) {
+ ret_val = e1000_wait_autoneg(hw);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error while waiting for autoneg to complete\n");
+ return ret_val;
+ }
+ }
+
+ hw->get_link_status = true;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_copper_link_postconfig - post link setup
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Config the MAC and the PHY after link is up.
+ * 1) Set up the MAC to the current PHY speed/duplex
+ * if we are on 82543. If we
+ * are on newer silicon, we only need to configure
+ * collision distance in the Transmit Control Register.
+ * 2) Set up flow control on the MAC to that established with
+ * the link partner.
+ * 3) Config DSP to improve Gigabit link quality for some PHY revisions.
+ */
+static s32 e1000_copper_link_postconfig(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ DEBUGFUNC("e1000_copper_link_postconfig");
+
+ if (hw->mac_type >= e1000_82544) {
+ e1000_config_collision_dist(hw);
+ } else {
+ ret_val = e1000_config_mac_to_phy(hw);
+ if (ret_val) {
+ DEBUGOUT("Error configuring MAC to PHY settings\n");
+ return ret_val;
+ }
+ }
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Configuring Flow Control\n");
+ return ret_val;
+ }
+
+ /* Config DSP to improve Giga link quality */
+ if (hw->phy_type == e1000_phy_igp) {
+ ret_val = e1000_config_dsp_after_link_change(hw, true);
+ if (ret_val) {
+ DEBUGOUT("Error Configuring DSP after link up\n");
+ return ret_val;
+ }
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_setup_copper_link - phy/speed/duplex setting
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Detects which PHY is present and sets up the speed and duplex
+ */
+static s32 e1000_setup_copper_link(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 i;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_setup_copper_link");
+
+ /* Check if it is a valid PHY and set PHY mode if necessary. */
+ ret_val = e1000_copper_link_preconfig(hw);
+ if (ret_val)
+ return ret_val;
+
+ if (hw->phy_type == e1000_phy_igp) {
+ ret_val = e1000_copper_link_igp_setup(hw);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->phy_type == e1000_phy_m88) {
+ ret_val = e1000_copper_link_mgp_setup(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ if (hw->autoneg) {
+ /* Setup autoneg and flow control advertisement
+ * and perform autonegotiation */
+ ret_val = e1000_copper_link_autoneg(hw);
+ if (ret_val)
+ return ret_val;
+ } else {
+ /* PHY will be set to 10H, 10F, 100H,or 100F
+ * depending on value from forced_speed_duplex. */
+ DEBUGOUT("Forcing speed and duplex\n");
+ ret_val = e1000_phy_force_speed_duplex(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Forcing Speed and Duplex\n");
+ return ret_val;
+ }
+ }
+
+ /* Check link status. Wait up to 100 microseconds for link to become
+ * valid.
+ */
+ for (i = 0; i < 10; i++) {
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (phy_data & MII_SR_LINK_STATUS) {
+ /* Config the MAC and PHY after link is up */
+ ret_val = e1000_copper_link_postconfig(hw);
+ if (ret_val)
+ return ret_val;
+
+ DEBUGOUT("Valid link established!!!\n");
+ return E1000_SUCCESS;
+ }
+ udelay(10);
+ }
+
+ DEBUGOUT("Unable to establish link!!!\n");
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_setup_autoneg - phy settings
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Configures PHY autoneg and flow control advertisement settings
+ */
+s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 mii_autoneg_adv_reg;
+ u16 mii_1000t_ctrl_reg;
+
+ DEBUGFUNC("e1000_phy_setup_autoneg");
+
+ /* Read the MII Auto-Neg Advertisement Register (Address 4). */
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
+
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+
+ /* Need to parse both autoneg_advertised and fc and set up
+ * the appropriate PHY registers. First we will parse for
+ * autoneg_advertised software override. Since we can advertise
+ * a plethora of combinations, we need to check each bit
+ * individually.
+ */
+
+ /* First we clear all the 10/100 mb speed bits in the Auto-Neg
+ * Advertisement Register (Address 4) and the 1000 mb speed bits in
+ * the 1000Base-T Control Register (Address 9).
+ */
+ mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
+ mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
+
+ DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
+
+ /* Do we want to advertise 10 Mb Half Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_10_HALF) {
+ DEBUGOUT("Advertise 10mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+ }
+
+ /* Do we want to advertise 10 Mb Full Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_10_FULL) {
+ DEBUGOUT("Advertise 10mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+ }
+
+ /* Do we want to advertise 100 Mb Half Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_100_HALF) {
+ DEBUGOUT("Advertise 100mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
+ }
+
+ /* Do we want to advertise 100 Mb Full Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_100_FULL) {
+ DEBUGOUT("Advertise 100mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+ }
+
+ /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
+ if (hw->autoneg_advertised & ADVERTISE_1000_HALF) {
+ DEBUGOUT
+ ("Advertise 1000mb Half duplex requested, request denied!\n");
+ }
+
+ /* Do we want to advertise 1000 Mb Full Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_1000_FULL) {
+ DEBUGOUT("Advertise 1000mb Full duplex\n");
+ mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+ }
+
+ /* Check for a software override of the flow control settings, and
+ * setup the PHY advertisement registers accordingly. If
+ * auto-negotiation is enabled, then software will have to set the
+ * "PAUSE" bits to the correct value in the Auto-Negotiation
+ * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * but we do not support receiving pause frames).
+ * 3: Both Rx and TX flow control (symmetric) are enabled.
+ * other: No software override. The flow control configuration
+ * in the EEPROM is used.
+ */
+ switch (hw->fc) {
+ case E1000_FC_NONE: /* 0 */
+ /* Flow control (RX & TX) is completely disabled by a
+ * software over-ride.
+ */
+ mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case E1000_FC_RX_PAUSE: /* 1 */
+ /* RX Flow control is enabled, and TX Flow control is
+ * disabled, by a software over-ride.
+ */
+ /* Since there really isn't a way to advertise that we are
+ * capable of RX Pause ONLY, we will advertise that we
+ * support both symmetric and asymmetric RX PAUSE. Later
+ * (in e1000_config_fc_after_link_up) we will disable the
+ *hw's ability to send PAUSE frames.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case E1000_FC_TX_PAUSE: /* 2 */
+ /* TX Flow control is enabled, and RX Flow control is
+ * disabled, by a software over-ride.
+ */
+ mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
+ mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+ break;
+ case E1000_FC_FULL: /* 3 */
+ /* Flow control (both RX and TX) is enabled by a software
+ * over-ride.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ default:
+ DEBUGOUT("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
+
+ DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
+
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_force_speed_duplex - force link settings
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Force PHY speed and duplex settings to hw->forced_speed_duplex
+ */
+static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 mii_ctrl_reg;
+ u16 mii_status_reg;
+ u16 phy_data;
+ u16 i;
+
+ DEBUGFUNC("e1000_phy_force_speed_duplex");
+
+ /* Turn off Flow control if we are forcing speed and duplex. */
+ hw->fc = E1000_FC_NONE;
+
+ DEBUGOUT1("hw->fc = %d\n", hw->fc);
+
+ /* Read the Device Control Register. */
+ ctrl = er32(CTRL);
+
+ /* Set the bits to Force Speed and Duplex in the Device Ctrl Reg. */
+ ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ctrl &= ~(DEVICE_SPEED_MASK);
+
+ /* Clear the Auto Speed Detect Enable bit. */
+ ctrl &= ~E1000_CTRL_ASDE;
+
+ /* Read the MII Control Register. */
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+
+ /* We need to disable autoneg in order to force link and duplex. */
+
+ mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN;
+
+ /* Are we forcing Full or Half Duplex? */
+ if (hw->forced_speed_duplex == e1000_100_full ||
+ hw->forced_speed_duplex == e1000_10_full) {
+ /* We want to force full duplex so we SET the full duplex bits in the
+ * Device and MII Control Registers.
+ */
+ ctrl |= E1000_CTRL_FD;
+ mii_ctrl_reg |= MII_CR_FULL_DUPLEX;
+ DEBUGOUT("Full Duplex\n");
+ } else {
+ /* We want to force half duplex so we CLEAR the full duplex bits in
+ * the Device and MII Control Registers.
+ */
+ ctrl &= ~E1000_CTRL_FD;
+ mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX;
+ DEBUGOUT("Half Duplex\n");
+ }
+
+ /* Are we forcing 100Mbps??? */
+ if (hw->forced_speed_duplex == e1000_100_full ||
+ hw->forced_speed_duplex == e1000_100_half) {
+ /* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */
+ ctrl |= E1000_CTRL_SPD_100;
+ mii_ctrl_reg |= MII_CR_SPEED_100;
+ mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
+ DEBUGOUT("Forcing 100mb ");
+ } else {
+ /* Set the 10Mb bit and turn off the 1000Mb and 100Mb bits. */
+ ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+ mii_ctrl_reg |= MII_CR_SPEED_10;
+ mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
+ DEBUGOUT("Forcing 10mb ");
+ }
+
+ e1000_config_collision_dist(hw);
+
+ /* Write the configured values back to the Device Control Reg. */
+ ew32(CTRL, ctrl);
+
+ if (hw->phy_type == e1000_phy_m88) {
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ * forced whenever speed are duplex are forced.
+ */
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data);
+
+ /* Need to reset the PHY or these changes will be ignored */
+ mii_ctrl_reg |= MII_CR_RESET;
+
+ /* Disable MDI-X support for 10/100 */
+ } else {
+ /* Clear Auto-Crossover to force MDI manually. IGP requires MDI
+ * forced whenever speed or duplex are forced.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Write back the modified PHY MII control register. */
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+
+ udelay(1);
+
+ /* The wait_autoneg_complete flag may be a little misleading here.
+ * Since we are forcing speed and duplex, Auto-Neg is not enabled.
+ * But we do want to delay for a period while forcing only so we
+ * don't generate false No Link messages. So we will wait here
+ * only if the user has set wait_autoneg_complete to 1, which is
+ * the default.
+ */
+ if (hw->wait_autoneg_complete) {
+ /* We will wait for autoneg to complete. */
+ DEBUGOUT("Waiting for forced speed/duplex link.\n");
+ mii_status_reg = 0;
+
+ /* We will wait for autoneg to complete or 4.5 seconds to expire. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Auto-Neg Complete bit
+ * to be set.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (mii_status_reg & MII_SR_LINK_STATUS)
+ break;
+ msleep(100);
+ }
+ if ((i == 0) && (hw->phy_type == e1000_phy_m88)) {
+ /* We didn't get link. Reset the DSP and wait again for link. */
+ ret_val = e1000_phy_reset_dsp(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting PHY DSP\n");
+ return ret_val;
+ }
+ }
+ /* This loop will early-out if the link condition has been met. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ if (mii_status_reg & MII_SR_LINK_STATUS)
+ break;
+ msleep(100);
+ /* Read the MII Status Register and wait for Auto-Neg Complete bit
+ * to be set.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+
+ if (hw->phy_type == e1000_phy_m88) {
+ /* Because we reset the PHY above, we need to re-force TX_CLK in the
+ * Extended PHY Specific Control Register to 25MHz clock. This value
+ * defaults back to a 2.5MHz clock when the PHY is reset.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* In addition, because of the s/w reset above, we need to enable CRS on
+ * TX. This must be set for both full and half duplex operation.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543)
+ && (!hw->autoneg)
+ && (hw->forced_speed_duplex == e1000_10_full
+ || hw->forced_speed_duplex == e1000_10_half)) {
+ ret_val = e1000_polarity_reversal_workaround(hw);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_config_collision_dist - set collision distance register
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Sets the collision distance in the Transmit Control register.
+ * Link should have been established previously. Reads the speed and duplex
+ * information from the Device Status register.
+ */
+void e1000_config_collision_dist(struct e1000_hw *hw)
+{
+ u32 tctl, coll_dist;
+
+ DEBUGFUNC("e1000_config_collision_dist");
+
+ if (hw->mac_type < e1000_82543)
+ coll_dist = E1000_COLLISION_DISTANCE_82542;
+ else
+ coll_dist = E1000_COLLISION_DISTANCE;
+
+ tctl = er32(TCTL);
+
+ tctl &= ~E1000_TCTL_COLD;
+ tctl |= coll_dist << E1000_COLD_SHIFT;
+
+ ew32(TCTL, tctl);
+ E1000_WRITE_FLUSH();
+}
+
+/**
+ * e1000_config_mac_to_phy - sync phy and mac settings
+ * @hw: Struct containing variables accessed by shared code
+ * @mii_reg: data to write to the MII control register
+ *
+ * Sets MAC speed and duplex settings to reflect the those in the PHY
+ * The contents of the PHY register containing the needed information need to
+ * be passed in.
+ */
+static s32 e1000_config_mac_to_phy(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_config_mac_to_phy");
+
+ /* 82544 or newer MAC, Auto Speed Detection takes care of
+ * MAC speed/duplex configuration.*/
+ if (hw->mac_type >= e1000_82544)
+ return E1000_SUCCESS;
+
+ /* Read the Device Control Register and set the bits to Force Speed
+ * and Duplex.
+ */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS);
+
+ /* Set up duplex in the Device Control and Transmit Control
+ * registers depending on negotiated values.
+ */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (phy_data & M88E1000_PSSR_DPLX)
+ ctrl |= E1000_CTRL_FD;
+ else
+ ctrl &= ~E1000_CTRL_FD;
+
+ e1000_config_collision_dist(hw);
+
+ /* Set up speed in the Device Control register depending on
+ * negotiated values.
+ */
+ if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
+ ctrl |= E1000_CTRL_SPD_1000;
+ else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
+ ctrl |= E1000_CTRL_SPD_100;
+
+ /* Write the configured values back to the Device Control Reg. */
+ ew32(CTRL, ctrl);
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_force_mac_fc - force flow control settings
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Forces the MAC's flow control settings.
+ * Sets the TFCE and RFCE bits in the device control register to reflect
+ * the adapter settings. TFCE and RFCE need to be explicitly set by
+ * software when a Copper PHY is used because autonegotiation is managed
+ * by the PHY rather than the MAC. Software must also configure these
+ * bits when link is forced on a fiber connection.
+ */
+s32 e1000_force_mac_fc(struct e1000_hw *hw)
+{
+ u32 ctrl;
+
+ DEBUGFUNC("e1000_force_mac_fc");
+
+ /* Get the current configuration of the Device Control Register */
+ ctrl = er32(CTRL);
+
+ /* Because we didn't get link via the internal auto-negotiation
+ * mechanism (we either forced link or we got link via PHY
+ * auto-neg), we have to manually enable/disable transmit an
+ * receive flow control.
+ *
+ * The "Case" statement below enables/disable flow control
+ * according to the "hw->fc" parameter.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause
+ * frames but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * frames but we do not receive pause frames).
+ * 3: Both Rx and TX flow control (symmetric) is enabled.
+ * other: No other values should be possible at this point.
+ */
+
+ switch (hw->fc) {
+ case E1000_FC_NONE:
+ ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
+ break;
+ case E1000_FC_RX_PAUSE:
+ ctrl &= (~E1000_CTRL_TFCE);
+ ctrl |= E1000_CTRL_RFCE;
+ break;
+ case E1000_FC_TX_PAUSE:
+ ctrl &= (~E1000_CTRL_RFCE);
+ ctrl |= E1000_CTRL_TFCE;
+ break;
+ case E1000_FC_FULL:
+ ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
+ break;
+ default:
+ DEBUGOUT("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ /* Disable TX Flow Control for 82542 (rev 2.0) */
+ if (hw->mac_type == e1000_82542_rev2_0)
+ ctrl &= (~E1000_CTRL_TFCE);
+
+ ew32(CTRL, ctrl);
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_config_fc_after_link_up - configure flow control after autoneg
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Configures flow control settings after link is established
+ * Should be called immediately after a valid link has been established.
+ * Forces MAC flow control settings if link was forced. When in MII/GMII mode
+ * and autonegotiation is enabled, the MAC flow control settings will be set
+ * based on the flow control negotiated by the PHY. In TBI mode, the TFCE
+ * and RFCE bits will be automatically set to the negotiated flow control mode.
+ */
+static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 mii_status_reg;
+ u16 mii_nway_adv_reg;
+ u16 mii_nway_lp_ability_reg;
+ u16 speed;
+ u16 duplex;
+
+ DEBUGFUNC("e1000_config_fc_after_link_up");
+
+ /* Check for the case where we have fiber media and auto-neg failed
+ * so we had to force link. In this case, we need to force the
+ * configuration of the MAC to match the "fc" parameter.
+ */
+ if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed))
+ || ((hw->media_type == e1000_media_type_internal_serdes)
+ && (hw->autoneg_failed))
+ || ((hw->media_type == e1000_media_type_copper)
+ && (!hw->autoneg))) {
+ ret_val = e1000_force_mac_fc(hw);
+ if (ret_val) {
+ DEBUGOUT("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ }
+
+ /* Check for the case where we have copper media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if ((hw->media_type == e1000_media_type_copper) && hw->autoneg) {
+ /* Read the MII Status Register and check to see if AutoNeg
+ * has completed. We read this twice because this reg has
+ * some "sticky" (latched) bits.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
+ /* The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement Register
+ * (Address 4) and the Auto_Negotiation Base Page Ability
+ * Register (Address 5) to determine how flow control was
+ * negotiated.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV,
+ &mii_nway_adv_reg);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY,
+ &mii_nway_lp_ability_reg);
+ if (ret_val)
+ return ret_val;
+
+ /* Two bits in the Auto Negotiation Advertisement Register
+ * (Address 4) and two bits in the Auto Negotiation Base
+ * Page Ability Register (Address 5) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | E1000_FC_NONE
+ * 0 | 1 | 0 | DC | E1000_FC_NONE
+ * 0 | 1 | 1 | 0 | E1000_FC_NONE
+ * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE
+ * 1 | 0 | 0 | DC | E1000_FC_NONE
+ * 1 | DC | 1 | DC | E1000_FC_FULL
+ * 1 | 1 | 0 | 0 | E1000_FC_NONE
+ * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE
+ *
+ */
+ /* Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | E1000_FC_FULL
+ *
+ */
+ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+ /* Now we need to check if the user selected RX ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->original_fc == E1000_FC_FULL) {
+ hw->fc = E1000_FC_FULL;
+ DEBUGOUT("Flow Control = FULL.\n");
+ } else {
+ hw->fc = E1000_FC_RX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = RX PAUSE frames only.\n");
+ }
+ }
+ /* For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE
+ *
+ */
+ else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
+ {
+ hw->fc = E1000_FC_TX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = TX PAUSE frames only.\n");
+ }
+ /* For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE
+ *
+ */
+ else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
+ {
+ hw->fc = E1000_FC_RX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = RX PAUSE frames only.\n");
+ }
+ /* Per the IEEE spec, at this point flow control should be
+ * disabled. However, we want to consider that we could
+ * be connected to a legacy switch that doesn't advertise
+ * desired flow control, but can be forced on the link
+ * partner. So if we advertised no flow control, that is
+ * what we will resolve to. If we advertised some kind of
+ * receive capability (Rx Pause Only or Full Flow Control)
+ * and the link partner advertised none, we will configure
+ * ourselves to enable Rx Flow Control only. We can do
+ * this safely for two reasons: If the link partner really
+ * didn't want flow control enabled, and we enable Rx, no
+ * harm done since we won't be receiving any PAUSE frames
+ * anyway. If the intent on the link partner was to have
+ * flow control enabled, then by us enabling RX only, we
+ * can at least receive pause frames and process them.
+ * This is a good idea because in most cases, since we are
+ * predominantly a server NIC, more times than not we will
+ * be asked to delay transmission of packets than asking
+ * our link partner to pause transmission of frames.
+ */
+ else if ((hw->original_fc == E1000_FC_NONE ||
+ hw->original_fc == E1000_FC_TX_PAUSE) ||
+ hw->fc_strict_ieee) {
+ hw->fc = E1000_FC_NONE;
+ DEBUGOUT("Flow Control = NONE.\n");
+ } else {
+ hw->fc = E1000_FC_RX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = RX PAUSE frames only.\n");
+ }
+
+ /* Now we need to do one last check... If we auto-
+ * negotiated to HALF DUPLEX, flow control should not be
+ * enabled per IEEE 802.3 spec.
+ */
+ ret_val =
+ e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error getting link speed and duplex\n");
+ return ret_val;
+ }
+
+ if (duplex == HALF_DUPLEX)
+ hw->fc = E1000_FC_NONE;
+
+ /* Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ ret_val = e1000_force_mac_fc(hw);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ } else {
+ DEBUGOUT
+ ("Copper PHY and Auto Neg has not completed.\n");
+ }
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_check_for_serdes_link_generic - Check for link (Serdes)
+ * @hw: pointer to the HW structure
+ *
+ * Checks for link up on the hardware. If link is not up and we have
+ * a signal, then we need to force link up.
+ */
+static s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw)
+{
+ u32 rxcw;
+ u32 ctrl;
+ u32 status;
+ s32 ret_val = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_check_for_serdes_link_generic");
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+ rxcw = er32(RXCW);
+
+ /*
+ * If we don't have link (auto-negotiation failed or link partner
+ * cannot auto-negotiate), and our link partner is not trying to
+ * auto-negotiate with us (we are receiving idles or data),
+ * we need to force link up. We also need to give auto-negotiation
+ * time to complete.
+ */
+ /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */
+ if ((!(status & E1000_STATUS_LU)) && (!(rxcw & E1000_RXCW_C))) {
+ if (hw->autoneg_failed == 0) {
+ hw->autoneg_failed = 1;
+ goto out;
+ }
+ DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n");
+
+ /* Disable auto-negotiation in the TXCW register */
+ ew32(TXCW, (hw->txcw & ~E1000_TXCW_ANE));
+
+ /* Force link-up and also force full-duplex. */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* Configure Flow Control after forcing link up. */
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if (ret_val) {
+ DEBUGOUT("Error configuring flow control\n");
+ goto out;
+ }
+ } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
+ /*
+ * If we are forcing link and we are receiving /C/ ordered
+ * sets, re-enable auto-negotiation in the TXCW register
+ * and disable forced link in the Device Control register
+ * in an attempt to auto-negotiate with our link partner.
+ */
+ DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n");
+ ew32(TXCW, hw->txcw);
+ ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
+
+ hw->serdes_has_link = true;
+ } else if (!(E1000_TXCW_ANE & er32(TXCW))) {
+ /*
+ * If we force link for non-auto-negotiation switch, check
+ * link status based on MAC synchronization for internal
+ * serdes media type.
+ */
+ /* SYNCH bit and IV bit are sticky. */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_SYNCH) {
+ if (!(rxcw & E1000_RXCW_IV)) {
+ hw->serdes_has_link = true;
+ DEBUGOUT("SERDES: Link up - forced.\n");
+ }
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - force failed.\n");
+ }
+ }
+
+ if (E1000_TXCW_ANE & er32(TXCW)) {
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU) {
+ /* SYNCH bit and IV bit are sticky, so reread rxcw. */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_SYNCH) {
+ if (!(rxcw & E1000_RXCW_IV)) {
+ hw->serdes_has_link = true;
+ DEBUGOUT("SERDES: Link up - autoneg "
+ "completed successfully.\n");
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - invalid"
+ "codewords detected in autoneg.\n");
+ }
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - no sync.\n");
+ }
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - autoneg failed\n");
+ }
+ }
+
+ out:
+ return ret_val;
+}
+
+/**
+ * e1000_check_for_link
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Checks to see if the link status of the hardware has changed.
+ * Called by any function that needs to check the link status of the adapter.
+ */
+s32 e1000_check_for_link(struct e1000_hw *hw)
+{
+ u32 rxcw = 0;
+ u32 ctrl;
+ u32 status;
+ u32 rctl;
+ u32 icr;
+ u32 signal = 0;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_check_for_link");
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+
+ /* On adapters with a MAC newer than 82544, SW Definable pin 1 will be
+ * set when the optics detect a signal. On older adapters, it will be
+ * cleared when there is a signal. This applies to fiber media only.
+ */
+ if ((hw->media_type == e1000_media_type_fiber) ||
+ (hw->media_type == e1000_media_type_internal_serdes)) {
+ rxcw = er32(RXCW);
+
+ if (hw->media_type == e1000_media_type_fiber) {
+ signal =
+ (hw->mac_type >
+ e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
+ if (status & E1000_STATUS_LU)
+ hw->get_link_status = false;
+ }
+ }
+
+ /* If we have a copper PHY then we only want to go out to the PHY
+ * registers to see if Auto-Neg has completed and/or if our link
+ * status has changed. The get_link_status flag will be set if we
+ * receive a Link Status Change interrupt or we have Rx Sequence
+ * Errors.
+ */
+ if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
+ /* First we want to see if the MII Status Register reports
+ * link. If so, then we want to get the current speed/duplex
+ * of the PHY.
+ * Read the register twice since the link bit is sticky.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (phy_data & MII_SR_LINK_STATUS) {
+ hw->get_link_status = false;
+ /* Check if there was DownShift, must be checked immediately after
+ * link-up */
+ e1000_check_downshift(hw);
+
+ /* If we are on 82544 or 82543 silicon and speed/duplex
+ * are forced to 10H or 10F, then we will implement the polarity
+ * reversal workaround. We disable interrupts first, and upon
+ * returning, place the devices interrupt state to its previous
+ * value except for the link status change interrupt which will
+ * happen due to the execution of this workaround.
+ */
+
+ if ((hw->mac_type == e1000_82544
+ || hw->mac_type == e1000_82543) && (!hw->autoneg)
+ && (hw->forced_speed_duplex == e1000_10_full
+ || hw->forced_speed_duplex == e1000_10_half)) {
+ ew32(IMC, 0xffffffff);
+ ret_val =
+ e1000_polarity_reversal_workaround(hw);
+ icr = er32(ICR);
+ ew32(ICS, (icr & ~E1000_ICS_LSC));
+ ew32(IMS, IMS_ENABLE_MASK);
+ }
+
+ } else {
+ /* No link detected */
+ e1000_config_dsp_after_link_change(hw, false);
+ return 0;
+ }
+
+ /* If we are forcing speed/duplex, then we simply return since
+ * we have already determined whether we have link or not.
+ */
+ if (!hw->autoneg)
+ return -E1000_ERR_CONFIG;
+
+ /* optimize the dsp settings for the igp phy */
+ e1000_config_dsp_after_link_change(hw, true);
+
+ /* We have a M88E1000 PHY and Auto-Neg is enabled. If we
+ * have Si on board that is 82544 or newer, Auto
+ * Speed Detection takes care of MAC speed/duplex
+ * configuration. So we only need to configure Collision
+ * Distance in the MAC. Otherwise, we need to force
+ * speed/duplex on the MAC to the current PHY speed/duplex
+ * settings.
+ */
+ if (hw->mac_type >= e1000_82544)
+ e1000_config_collision_dist(hw);
+ else {
+ ret_val = e1000_config_mac_to_phy(hw);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error configuring MAC to PHY settings\n");
+ return ret_val;
+ }
+ }
+
+ /* Configure Flow Control now that Auto-Neg has completed. First, we
+ * need to restore the desired flow control settings because we may
+ * have had to re-autoneg with a different link partner.
+ */
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if (ret_val) {
+ DEBUGOUT("Error configuring flow control\n");
+ return ret_val;
+ }
+
+ /* At this point we know that we are on copper and we have
+ * auto-negotiated link. These are conditions for checking the link
+ * partner capability register. We use the link speed to determine if
+ * TBI compatibility needs to be turned on or off. If the link is not
+ * at gigabit speed, then TBI compatibility is not needed. If we are
+ * at gigabit speed, we turn on TBI compatibility.
+ */
+ if (hw->tbi_compatibility_en) {
+ u16 speed, duplex;
+ ret_val =
+ e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error getting link speed and duplex\n");
+ return ret_val;
+ }
+ if (speed != SPEED_1000) {
+ /* If link speed is not set to gigabit speed, we do not need
+ * to enable TBI compatibility.
+ */
+ if (hw->tbi_compatibility_on) {
+ /* If we previously were in the mode, turn it off. */
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_SBP;
+ ew32(RCTL, rctl);
+ hw->tbi_compatibility_on = false;
+ }
+ } else {
+ /* If TBI compatibility is was previously off, turn it on. For
+ * compatibility with a TBI link partner, we will store bad
+ * packets. Some frames have an additional byte on the end and
+ * will look like CRC errors to to the hardware.
+ */
+ if (!hw->tbi_compatibility_on) {
+ hw->tbi_compatibility_on = true;
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_SBP;
+ ew32(RCTL, rctl);
+ }
+ }
+ }
+ }
+
+ if ((hw->media_type == e1000_media_type_fiber) ||
+ (hw->media_type == e1000_media_type_internal_serdes))
+ e1000_check_for_serdes_link_generic(hw);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_get_speed_and_duplex
+ * @hw: Struct containing variables accessed by shared code
+ * @speed: Speed of the connection
+ * @duplex: Duplex setting of the connection
+
+ * Detects the current speed and duplex settings of the hardware.
+ */
+s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 *speed, u16 *duplex)
+{
+ u32 status;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_get_speed_and_duplex");
+
+ if (hw->mac_type >= e1000_82543) {
+ status = er32(STATUS);
+ if (status & E1000_STATUS_SPEED_1000) {
+ *speed = SPEED_1000;
+ DEBUGOUT("1000 Mbs, ");
+ } else if (status & E1000_STATUS_SPEED_100) {
+ *speed = SPEED_100;
+ DEBUGOUT("100 Mbs, ");
+ } else {
+ *speed = SPEED_10;
+ DEBUGOUT("10 Mbs, ");
+ }
+
+ if (status & E1000_STATUS_FD) {
+ *duplex = FULL_DUPLEX;
+ DEBUGOUT("Full Duplex\n");
+ } else {
+ *duplex = HALF_DUPLEX;
+ DEBUGOUT(" Half Duplex\n");
+ }
+ } else {
+ DEBUGOUT("1000 Mbs, Full Duplex\n");
+ *speed = SPEED_1000;
+ *duplex = FULL_DUPLEX;
+ }
+
+ /* IGP01 PHY may advertise full duplex operation after speed downgrade even
+ * if it is operating at half duplex. Here we set the duplex settings to
+ * match the duplex in the link partner's capabilities.
+ */
+ if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) {
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (!(phy_data & NWAY_ER_LP_NWAY_CAPS))
+ *duplex = HALF_DUPLEX;
+ else {
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_LP_ABILITY, &phy_data);
+ if (ret_val)
+ return ret_val;
+ if ((*speed == SPEED_100
+ && !(phy_data & NWAY_LPAR_100TX_FD_CAPS))
+ || (*speed == SPEED_10
+ && !(phy_data & NWAY_LPAR_10T_FD_CAPS)))
+ *duplex = HALF_DUPLEX;
+ }
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_wait_autoneg
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Blocks until autoneg completes or times out (~4.5 seconds)
+ */
+static s32 e1000_wait_autoneg(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 i;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_wait_autoneg");
+ DEBUGOUT("Waiting for Auto-Neg to complete.\n");
+
+ /* We will wait for autoneg to complete or 4.5 seconds to expire. */
+ for (i = PHY_AUTO_NEG_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Auto-Neg
+ * Complete bit to be set.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ if (phy_data & MII_SR_AUTONEG_COMPLETE) {
+ return E1000_SUCCESS;
+ }
+ msleep(100);
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_raise_mdi_clk - Raises the Management Data Clock
+ * @hw: Struct containing variables accessed by shared code
+ * @ctrl: Device control register's current value
+ */
+static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl)
+{
+ /* Raise the clock input to the Management Data Clock (by setting the MDC
+ * bit), and then delay 10 microseconds.
+ */
+ ew32(CTRL, (*ctrl | E1000_CTRL_MDC));
+ E1000_WRITE_FLUSH();
+ udelay(10);
+}
+
+/**
+ * e1000_lower_mdi_clk - Lowers the Management Data Clock
+ * @hw: Struct containing variables accessed by shared code
+ * @ctrl: Device control register's current value
+ */
+static void e1000_lower_mdi_clk(struct e1000_hw *hw, u32 *ctrl)
+{
+ /* Lower the clock input to the Management Data Clock (by clearing the MDC
+ * bit), and then delay 10 microseconds.
+ */
+ ew32(CTRL, (*ctrl & ~E1000_CTRL_MDC));
+ E1000_WRITE_FLUSH();
+ udelay(10);
+}
+
+/**
+ * e1000_shift_out_mdi_bits - Shifts data bits out to the PHY
+ * @hw: Struct containing variables accessed by shared code
+ * @data: Data to send out to the PHY
+ * @count: Number of bits to shift out
+ *
+ * Bits are shifted out in MSB to LSB order.
+ */
+static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count)
+{
+ u32 ctrl;
+ u32 mask;
+
+ /* We need to shift "count" number of bits out to the PHY. So, the value
+ * in the "data" parameter will be shifted out to the PHY one bit at a
+ * time. In order to do this, "data" must be broken down into bits.
+ */
+ mask = 0x01;
+ mask <<= (count - 1);
+
+ ctrl = er32(CTRL);
+
+ /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */
+ ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR);
+
+ while (mask) {
+ /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and
+ * then raising and lowering the Management Data Clock. A "0" is
+ * shifted out to the PHY by setting the MDIO bit to "0" and then
+ * raising and lowering the clock.
+ */
+ if (data & mask)
+ ctrl |= E1000_CTRL_MDIO;
+ else
+ ctrl &= ~E1000_CTRL_MDIO;
+
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
+
+ udelay(10);
+
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
+
+ mask = mask >> 1;
+ }
+}
+
+/**
+ * e1000_shift_in_mdi_bits - Shifts data bits in from the PHY
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Bits are shifted in in MSB to LSB order.
+ */
+static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u16 data = 0;
+ u8 i;
+
+ /* In order to read a register from the PHY, we need to shift in a total
+ * of 18 bits from the PHY. The first two bit (turnaround) times are used
+ * to avoid contention on the MDIO pin when a read operation is performed.
+ * These two bits are ignored by us and thrown away. Bits are "shifted in"
+ * by raising the input to the Management Data Clock (setting the MDC bit),
+ * and then reading the value of the MDIO bit.
+ */
+ ctrl = er32(CTRL);
+
+ /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */
+ ctrl &= ~E1000_CTRL_MDIO_DIR;
+ ctrl &= ~E1000_CTRL_MDIO;
+
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
+
+ /* Raise and Lower the clock before reading in the data. This accounts for
+ * the turnaround bits. The first clock occurred when we clocked out the
+ * last bit of the Register Address.
+ */
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
+
+ for (data = 0, i = 0; i < 16; i++) {
+ data = data << 1;
+ e1000_raise_mdi_clk(hw, &ctrl);
+ ctrl = er32(CTRL);
+ /* Check to see if we shifted in a "1". */
+ if (ctrl & E1000_CTRL_MDIO)
+ data |= 1;
+ e1000_lower_mdi_clk(hw, &ctrl);
+ }
+
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
+
+ return data;
+}
+
+
+/**
+ * e1000_read_phy_reg - read a phy register
+ * @hw: Struct containing variables accessed by shared code
+ * @reg_addr: address of the PHY register to read
+ *
+ * Reads the value from a PHY register, if the value is on a specific non zero
+ * page, sets the page first.
+ */
+s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 *phy_data)
+{
+ u32 ret_val;
+
+ DEBUGFUNC("e1000_read_phy_reg");
+
+ if ((hw->phy_type == e1000_phy_igp) &&
+ (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+ ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (u16) reg_addr);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
+ phy_data);
+
+ return ret_val;
+}
+
+static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
+ u16 *phy_data)
+{
+ u32 i;
+ u32 mdic = 0;
+ const u32 phy_addr = 1;
+
+ DEBUGFUNC("e1000_read_phy_reg_ex");
+
+ if (reg_addr > MAX_PHY_REG_ADDRESS) {
+ DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
+ return -E1000_ERR_PARAM;
+ }
+
+ if (hw->mac_type > e1000_82543) {
+ /* Set up Op-code, Phy Address, and register address in the MDI
+ * Control register. The MAC will take care of interfacing with the
+ * PHY to retrieve the desired data.
+ */
+ mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
+ (phy_addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_READ));
+
+ ew32(MDIC, mdic);
+
+ /* Poll the ready bit to see if the MDI read completed */
+ for (i = 0; i < 64; i++) {
+ udelay(50);
+ mdic = er32(MDIC);
+ if (mdic & E1000_MDIC_READY)
+ break;
+ }
+ if (!(mdic & E1000_MDIC_READY)) {
+ DEBUGOUT("MDI Read did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ if (mdic & E1000_MDIC_ERROR) {
+ DEBUGOUT("MDI Error\n");
+ return -E1000_ERR_PHY;
+ }
+ *phy_data = (u16) mdic;
+ } else {
+ /* We must first send a preamble through the MDIO pin to signal the
+ * beginning of an MII instruction. This is done by sending 32
+ * consecutive "1" bits.
+ */
+ e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
+
+ /* Now combine the next few fields that are required for a read
+ * operation. We use this method instead of calling the
+ * e1000_shift_out_mdi_bits routine five different times. The format of
+ * a MII read instruction consists of a shift out of 14 bits and is
+ * defined as follows:
+ * <Preamble><SOF><Op Code><Phy Addr><Reg Addr>
+ * followed by a shift in of 18 bits. This first two bits shifted in
+ * are TurnAround bits used to avoid contention on the MDIO pin when a
+ * READ operation is performed. These two bits are thrown away
+ * followed by a shift in of 16 bits which contains the desired data.
+ */
+ mdic = ((reg_addr) | (phy_addr << 5) |
+ (PHY_OP_READ << 10) | (PHY_SOF << 12));
+
+ e1000_shift_out_mdi_bits(hw, mdic, 14);
+
+ /* Now that we've shifted out the read command to the MII, we need to
+ * "shift in" the 16-bit value (18 total bits) of the requested PHY
+ * register address.
+ */
+ *phy_data = e1000_shift_in_mdi_bits(hw);
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_write_phy_reg - write a phy register
+ *
+ * @hw: Struct containing variables accessed by shared code
+ * @reg_addr: address of the PHY register to write
+ * @data: data to write to the PHY
+
+ * Writes a value to a PHY register
+ */
+s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 phy_data)
+{
+ u32 ret_val;
+
+ DEBUGFUNC("e1000_write_phy_reg");
+
+ if ((hw->phy_type == e1000_phy_igp) &&
+ (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+ ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (u16) reg_addr);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
+ phy_data);
+
+ return ret_val;
+}
+
+static s32 e1000_write_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
+ u16 phy_data)
+{
+ u32 i;
+ u32 mdic = 0;
+ const u32 phy_addr = 1;
+
+ DEBUGFUNC("e1000_write_phy_reg_ex");
+
+ if (reg_addr > MAX_PHY_REG_ADDRESS) {
+ DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
+ return -E1000_ERR_PARAM;
+ }
+
+ if (hw->mac_type > e1000_82543) {
+ /* Set up Op-code, Phy Address, register address, and data intended
+ * for the PHY register in the MDI Control register. The MAC will take
+ * care of interfacing with the PHY to send the desired data.
+ */
+ mdic = (((u32) phy_data) |
+ (reg_addr << E1000_MDIC_REG_SHIFT) |
+ (phy_addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_WRITE));
+
+ ew32(MDIC, mdic);
+
+ /* Poll the ready bit to see if the MDI read completed */
+ for (i = 0; i < 641; i++) {
+ udelay(5);
+ mdic = er32(MDIC);
+ if (mdic & E1000_MDIC_READY)
+ break;
+ }
+ if (!(mdic & E1000_MDIC_READY)) {
+ DEBUGOUT("MDI Write did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ } else {
+ /* We'll need to use the SW defined pins to shift the write command
+ * out to the PHY. We first send a preamble to the PHY to signal the
+ * beginning of the MII instruction. This is done by sending 32
+ * consecutive "1" bits.
+ */
+ e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
+
+ /* Now combine the remaining required fields that will indicate a
+ * write operation. We use this method instead of calling the
+ * e1000_shift_out_mdi_bits routine for each field in the command. The
+ * format of a MII write instruction is as follows:
+ * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>.
+ */
+ mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) |
+ (PHY_OP_WRITE << 12) | (PHY_SOF << 14));
+ mdic <<= 16;
+ mdic |= (u32) phy_data;
+
+ e1000_shift_out_mdi_bits(hw, mdic, 32);
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_hw_reset - reset the phy, hardware style
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Returns the PHY to the power-on reset state
+ */
+s32 e1000_phy_hw_reset(struct e1000_hw *hw)
+{
+ u32 ctrl, ctrl_ext;
+ u32 led_ctrl;
+ s32 ret_val;
+
+ DEBUGFUNC("e1000_phy_hw_reset");
+
+ DEBUGOUT("Resetting Phy...\n");
+
+ if (hw->mac_type > e1000_82543) {
+ /* Read the device control register and assert the E1000_CTRL_PHY_RST
+ * bit. Then, take it out of reset.
+ * For e1000 hardware, we delay for 10ms between the assert
+ * and deassert.
+ */
+ ctrl = er32(CTRL);
+ ew32(CTRL, ctrl | E1000_CTRL_PHY_RST);
+ E1000_WRITE_FLUSH();
+
+ msleep(10);
+
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
+
+ } else {
+ /* Read the Extended Device Control Register, assert the PHY_RESET_DIR
+ * bit to put the PHY into reset. Then, take it out of reset.
+ */
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR;
+ ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA;
+ ew32(CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH();
+ msleep(10);
+ ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA;
+ ew32(CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH();
+ }
+ udelay(150);
+
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ /* Configure activity LED after PHY reset */
+ led_ctrl = er32(LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ ew32(LEDCTL, led_ctrl);
+ }
+
+ /* Wait for FW to finish PHY configuration. */
+ ret_val = e1000_get_phy_cfg_done(hw);
+ if (ret_val != E1000_SUCCESS)
+ return ret_val;
+
+ return ret_val;
+}
+
+/**
+ * e1000_phy_reset - reset the phy to commit settings
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Resets the PHY
+ * Sets bit 15 of the MII Control register
+ */
+s32 e1000_phy_reset(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_phy_reset");
+
+ switch (hw->phy_type) {
+ case e1000_phy_igp:
+ ret_val = e1000_phy_hw_reset(hw);
+ if (ret_val)
+ return ret_val;
+ break;
+ default:
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= MII_CR_RESET;
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ udelay(1);
+ break;
+ }
+
+ if (hw->phy_type == e1000_phy_igp)
+ e1000_phy_init_script(hw);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_detect_gig_phy - check the phy type
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Probes the expected PHY address for known PHY IDs
+ */
+static s32 e1000_detect_gig_phy(struct e1000_hw *hw)
+{
+ s32 phy_init_status, ret_val;
+ u16 phy_id_high, phy_id_low;
+ bool match = false;
+
+ DEBUGFUNC("e1000_detect_gig_phy");
+
+ if (hw->phy_id != 0)
+ return E1000_SUCCESS;
+
+ /* Read the PHY ID Registers to identify which PHY is onboard. */
+ ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy_id = (u32) (phy_id_high << 16);
+ udelay(20);
+ ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy_id |= (u32) (phy_id_low & PHY_REVISION_MASK);
+ hw->phy_revision = (u32) phy_id_low & ~PHY_REVISION_MASK;
+
+ switch (hw->mac_type) {
+ case e1000_82543:
+ if (hw->phy_id == M88E1000_E_PHY_ID)
+ match = true;
+ break;
+ case e1000_82544:
+ if (hw->phy_id == M88E1000_I_PHY_ID)
+ match = true;
+ break;
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ if (hw->phy_id == M88E1011_I_PHY_ID)
+ match = true;
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ if (hw->phy_id == IGP01E1000_I_PHY_ID)
+ match = true;
+ break;
+ default:
+ DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
+ return -E1000_ERR_CONFIG;
+ }
+ phy_init_status = e1000_set_phy_type(hw);
+
+ if ((match) && (phy_init_status == E1000_SUCCESS)) {
+ DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id);
+ return E1000_SUCCESS;
+ }
+ DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id);
+ return -E1000_ERR_PHY;
+}
+
+/**
+ * e1000_phy_reset_dsp - reset DSP
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Resets the PHY's DSP
+ */
+static s32 e1000_phy_reset_dsp(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ DEBUGFUNC("e1000_phy_reset_dsp");
+
+ do {
+ ret_val = e1000_write_phy_reg(hw, 29, 0x001d);
+ if (ret_val)
+ break;
+ ret_val = e1000_write_phy_reg(hw, 30, 0x00c1);
+ if (ret_val)
+ break;
+ ret_val = e1000_write_phy_reg(hw, 30, 0x0000);
+ if (ret_val)
+ break;
+ ret_val = E1000_SUCCESS;
+ } while (0);
+
+ return ret_val;
+}
+
+/**
+ * e1000_phy_igp_get_info - get igp specific registers
+ * @hw: Struct containing variables accessed by shared code
+ * @phy_info: PHY information structure
+ *
+ * Get PHY information from various PHY registers for igp PHY only.
+ */
+static s32 e1000_phy_igp_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info)
+{
+ s32 ret_val;
+ u16 phy_data, min_length, max_length, average;
+ e1000_rev_polarity polarity;
+
+ DEBUGFUNC("e1000_phy_igp_get_info");
+
+ /* The downshift status is checked only once, after link is established,
+ * and it stored in the hw->speed_downgraded parameter. */
+ phy_info->downshift = (e1000_downshift) hw->speed_downgraded;
+
+ /* IGP01E1000 does not need to support it. */
+ phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal;
+
+ /* IGP01E1000 always correct polarity reversal */
+ phy_info->polarity_correction = e1000_polarity_reversal_enabled;
+
+ /* Check polarity status */
+ ret_val = e1000_check_polarity(hw, &polarity);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->cable_polarity = polarity;
+
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->mdix_mode =
+ (e1000_auto_x_mode) ((phy_data & IGP01E1000_PSSR_MDIX) >>
+ IGP01E1000_PSSR_MDIX_SHIFT);
+
+ if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+ /* Local/Remote Receiver Information are only valid at 1000 Mbps */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >>
+ SR_1000T_LOCAL_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+ phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >>
+ SR_1000T_REMOTE_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+
+ /* Get cable length */
+ ret_val = e1000_get_cable_length(hw, &min_length, &max_length);
+ if (ret_val)
+ return ret_val;
+
+ /* Translate to old method */
+ average = (max_length + min_length) / 2;
+
+ if (average <= e1000_igp_cable_length_50)
+ phy_info->cable_length = e1000_cable_length_50;
+ else if (average <= e1000_igp_cable_length_80)
+ phy_info->cable_length = e1000_cable_length_50_80;
+ else if (average <= e1000_igp_cable_length_110)
+ phy_info->cable_length = e1000_cable_length_80_110;
+ else if (average <= e1000_igp_cable_length_140)
+ phy_info->cable_length = e1000_cable_length_110_140;
+ else
+ phy_info->cable_length = e1000_cable_length_140;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_m88_get_info - get m88 specific registers
+ * @hw: Struct containing variables accessed by shared code
+ * @phy_info: PHY information structure
+ *
+ * Get PHY information from various PHY registers for m88 PHY only.
+ */
+static s32 e1000_phy_m88_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info)
+{
+ s32 ret_val;
+ u16 phy_data;
+ e1000_rev_polarity polarity;
+
+ DEBUGFUNC("e1000_phy_m88_get_info");
+
+ /* The downshift status is checked only once, after link is established,
+ * and it stored in the hw->speed_downgraded parameter. */
+ phy_info->downshift = (e1000_downshift) hw->speed_downgraded;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->extended_10bt_distance =
+ ((phy_data & M88E1000_PSCR_10BT_EXT_DIST_ENABLE) >>
+ M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT) ?
+ e1000_10bt_ext_dist_enable_lower :
+ e1000_10bt_ext_dist_enable_normal;
+
+ phy_info->polarity_correction =
+ ((phy_data & M88E1000_PSCR_POLARITY_REVERSAL) >>
+ M88E1000_PSCR_POLARITY_REVERSAL_SHIFT) ?
+ e1000_polarity_reversal_disabled : e1000_polarity_reversal_enabled;
+
+ /* Check polarity status */
+ ret_val = e1000_check_polarity(hw, &polarity);
+ if (ret_val)
+ return ret_val;
+ phy_info->cable_polarity = polarity;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->mdix_mode =
+ (e1000_auto_x_mode) ((phy_data & M88E1000_PSSR_MDIX) >>
+ M88E1000_PSSR_MDIX_SHIFT);
+
+ if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) {
+ /* Cable Length Estimation and Local/Remote Receiver Information
+ * are only valid at 1000 Mbps.
+ */
+ phy_info->cable_length =
+ (e1000_cable_length) ((phy_data &
+ M88E1000_PSSR_CABLE_LENGTH) >>
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT);
+
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >>
+ SR_1000T_LOCAL_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+ phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >>
+ SR_1000T_REMOTE_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_get_info - request phy info
+ * @hw: Struct containing variables accessed by shared code
+ * @phy_info: PHY information structure
+ *
+ * Get PHY information from various PHY registers
+ */
+s32 e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_phy_get_info");
+
+ phy_info->cable_length = e1000_cable_length_undefined;
+ phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_undefined;
+ phy_info->cable_polarity = e1000_rev_polarity_undefined;
+ phy_info->downshift = e1000_downshift_undefined;
+ phy_info->polarity_correction = e1000_polarity_reversal_undefined;
+ phy_info->mdix_mode = e1000_auto_x_mode_undefined;
+ phy_info->local_rx = e1000_1000t_rx_status_undefined;
+ phy_info->remote_rx = e1000_1000t_rx_status_undefined;
+
+ if (hw->media_type != e1000_media_type_copper) {
+ DEBUGOUT("PHY info is only valid for copper media\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) {
+ DEBUGOUT("PHY info is only valid if link is up\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ if (hw->phy_type == e1000_phy_igp)
+ return e1000_phy_igp_get_info(hw, phy_info);
+ else
+ return e1000_phy_m88_get_info(hw, phy_info);
+}
+
+s32 e1000_validate_mdi_setting(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_validate_mdi_settings");
+
+ if (!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) {
+ DEBUGOUT("Invalid MDI setting detected\n");
+ hw->mdix = 1;
+ return -E1000_ERR_CONFIG;
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_init_eeprom_params - initialize sw eeprom vars
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Sets up eeprom variables in the hw struct. Must be called after mac_type
+ * is configured.
+ */
+s32 e1000_init_eeprom_params(struct e1000_hw *hw)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd = er32(EECD);
+ s32 ret_val = E1000_SUCCESS;
+ u16 eeprom_size;
+
+ DEBUGFUNC("e1000_init_eeprom_params");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->word_size = 64;
+ eeprom->opcode_bits = 3;
+ eeprom->address_bits = 6;
+ eeprom->delay_usec = 50;
+ break;
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->opcode_bits = 3;
+ eeprom->delay_usec = 50;
+ if (eecd & E1000_EECD_SIZE) {
+ eeprom->word_size = 256;
+ eeprom->address_bits = 8;
+ } else {
+ eeprom->word_size = 64;
+ eeprom->address_bits = 6;
+ }
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ if (eecd & E1000_EECD_TYPE) {
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ } else {
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->opcode_bits = 3;
+ eeprom->delay_usec = 50;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->word_size = 256;
+ eeprom->address_bits = 8;
+ } else {
+ eeprom->word_size = 64;
+ eeprom->address_bits = 6;
+ }
+ }
+ break;
+ default:
+ break;
+ }
+
+ if (eeprom->type == e1000_eeprom_spi) {
+ /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to
+ * 32KB (incremented by powers of 2).
+ */
+ /* Set to default value for initial eeprom read. */
+ eeprom->word_size = 64;
+ ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size);
+ if (ret_val)
+ return ret_val;
+ eeprom_size =
+ (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT;
+ /* 256B eeprom size was not supported in earlier hardware, so we
+ * bump eeprom_size up one to ensure that "1" (which maps to 256B)
+ * is never the result used in the shifting logic below. */
+ if (eeprom_size)
+ eeprom_size++;
+
+ eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT);
+ }
+ return ret_val;
+}
+
+/**
+ * e1000_raise_ee_clk - Raises the EEPROM's clock input.
+ * @hw: Struct containing variables accessed by shared code
+ * @eecd: EECD's current value
+ */
+static void e1000_raise_ee_clk(struct e1000_hw *hw, u32 *eecd)
+{
+ /* Raise the clock input to the EEPROM (by setting the SK bit), and then
+ * wait <delay> microseconds.
+ */
+ *eecd = *eecd | E1000_EECD_SK;
+ ew32(EECD, *eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
+}
+
+/**
+ * e1000_lower_ee_clk - Lowers the EEPROM's clock input.
+ * @hw: Struct containing variables accessed by shared code
+ * @eecd: EECD's current value
+ */
+static void e1000_lower_ee_clk(struct e1000_hw *hw, u32 *eecd)
+{
+ /* Lower the clock input to the EEPROM (by clearing the SK bit), and then
+ * wait 50 microseconds.
+ */
+ *eecd = *eecd & ~E1000_EECD_SK;
+ ew32(EECD, *eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
+}
+
+/**
+ * e1000_shift_out_ee_bits - Shift data bits out to the EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @data: data to send to the EEPROM
+ * @count: number of bits to shift out
+ */
+static void e1000_shift_out_ee_bits(struct e1000_hw *hw, u16 data, u16 count)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd;
+ u32 mask;
+
+ /* We need to shift "count" bits out to the EEPROM. So, value in the
+ * "data" parameter will be shifted out to the EEPROM one bit at a time.
+ * In order to do this, "data" must be broken down into bits.
+ */
+ mask = 0x01 << (count - 1);
+ eecd = er32(EECD);
+ if (eeprom->type == e1000_eeprom_microwire) {
+ eecd &= ~E1000_EECD_DO;
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ eecd |= E1000_EECD_DO;
+ }
+ do {
+ /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1",
+ * and then raising and then lowering the clock (the SK bit controls
+ * the clock input to the EEPROM). A "0" is shifted out to the EEPROM
+ * by setting "DI" to "0" and then raising and then lowering the clock.
+ */
+ eecd &= ~E1000_EECD_DI;
+
+ if (data & mask)
+ eecd |= E1000_EECD_DI;
+
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+
+ udelay(eeprom->delay_usec);
+
+ e1000_raise_ee_clk(hw, &eecd);
+ e1000_lower_ee_clk(hw, &eecd);
+
+ mask = mask >> 1;
+
+ } while (mask);
+
+ /* We leave the "DI" bit set to "0" when we leave this routine. */
+ eecd &= ~E1000_EECD_DI;
+ ew32(EECD, eecd);
+}
+
+/**
+ * e1000_shift_in_ee_bits - Shift data bits in from the EEPROM
+ * @hw: Struct containing variables accessed by shared code
+ * @count: number of bits to shift in
+ */
+static u16 e1000_shift_in_ee_bits(struct e1000_hw *hw, u16 count)
+{
+ u32 eecd;
+ u32 i;
+ u16 data;
+
+ /* In order to read a register from the EEPROM, we need to shift 'count'
+ * bits in from the EEPROM. Bits are "shifted in" by raising the clock
+ * input to the EEPROM (setting the SK bit), and then reading the value of
+ * the "DO" bit. During this "shifting in" process the "DI" bit should
+ * always be clear.
+ */
+
+ eecd = er32(EECD);
+
+ eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
+ data = 0;
+
+ for (i = 0; i < count; i++) {
+ data = data << 1;
+ e1000_raise_ee_clk(hw, &eecd);
+
+ eecd = er32(EECD);
+
+ eecd &= ~(E1000_EECD_DI);
+ if (eecd & E1000_EECD_DO)
+ data |= 1;
+
+ e1000_lower_ee_clk(hw, &eecd);
+ }
+
+ return data;
+}
+
+/**
+ * e1000_acquire_eeprom - Prepares EEPROM for access
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This
+ * function should be called before issuing a command to the EEPROM.
+ */
+static s32 e1000_acquire_eeprom(struct e1000_hw *hw)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd, i = 0;
+
+ DEBUGFUNC("e1000_acquire_eeprom");
+
+ eecd = er32(EECD);
+
+ /* Request EEPROM Access */
+ if (hw->mac_type > e1000_82544) {
+ eecd |= E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ eecd = er32(EECD);
+ while ((!(eecd & E1000_EECD_GNT)) &&
+ (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
+ i++;
+ udelay(5);
+ eecd = er32(EECD);
+ }
+ if (!(eecd & E1000_EECD_GNT)) {
+ eecd &= ~E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ DEBUGOUT("Could not acquire EEPROM grant\n");
+ return -E1000_ERR_EEPROM;
+ }
+ }
+
+ /* Setup EEPROM for Read/Write */
+
+ if (eeprom->type == e1000_eeprom_microwire) {
+ /* Clear SK and DI */
+ eecd &= ~(E1000_EECD_DI | E1000_EECD_SK);
+ ew32(EECD, eecd);
+
+ /* Set CS */
+ eecd |= E1000_EECD_CS;
+ ew32(EECD, eecd);
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ /* Clear SK and CS */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ ew32(EECD, eecd);
+ udelay(1);
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_standby_eeprom - Returns EEPROM to a "standby" state
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_standby_eeprom(struct e1000_hw *hw)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd;
+
+ eecd = er32(EECD);
+
+ if (eeprom->type == e1000_eeprom_microwire) {
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+
+ /* Clock high */
+ eecd |= E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+
+ /* Select EEPROM */
+ eecd |= E1000_EECD_CS;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+
+ /* Clock low */
+ eecd &= ~E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ /* Toggle CS to flush commands */
+ eecd |= E1000_EECD_CS;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+ eecd &= ~E1000_EECD_CS;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+ }
+}
+
+/**
+ * e1000_release_eeprom - drop chip select
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Terminates a command by inverting the EEPROM's chip select pin
+ */
+static void e1000_release_eeprom(struct e1000_hw *hw)
+{
+ u32 eecd;
+
+ DEBUGFUNC("e1000_release_eeprom");
+
+ eecd = er32(EECD);
+
+ if (hw->eeprom.type == e1000_eeprom_spi) {
+ eecd |= E1000_EECD_CS; /* Pull CS high */
+ eecd &= ~E1000_EECD_SK; /* Lower SCK */
+
+ ew32(EECD, eecd);
+
+ udelay(hw->eeprom.delay_usec);
+ } else if (hw->eeprom.type == e1000_eeprom_microwire) {
+ /* cleanup eeprom */
+
+ /* CS on Microwire is active-high */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);
+
+ ew32(EECD, eecd);
+
+ /* Rising edge of clock */
+ eecd |= E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
+
+ /* Falling edge of clock */
+ eecd &= ~E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
+ }
+
+ /* Stop requesting EEPROM access */
+ if (hw->mac_type > e1000_82544) {
+ eecd &= ~E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ }
+}
+
+/**
+ * e1000_spi_eeprom_ready - Reads a 16 bit word from the EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static s32 e1000_spi_eeprom_ready(struct e1000_hw *hw)
+{
+ u16 retry_count = 0;
+ u8 spi_stat_reg;
+
+ DEBUGFUNC("e1000_spi_eeprom_ready");
+
+ /* Read "Status Register" repeatedly until the LSB is cleared. The
+ * EEPROM will signal that the command has been completed by clearing
+ * bit 0 of the internal status register. If it's not cleared within
+ * 5 milliseconds, then error out.
+ */
+ retry_count = 0;
+ do {
+ e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI,
+ hw->eeprom.opcode_bits);
+ spi_stat_reg = (u8) e1000_shift_in_ee_bits(hw, 8);
+ if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI))
+ break;
+
+ udelay(5);
+ retry_count += 5;
+
+ e1000_standby_eeprom(hw);
+ } while (retry_count < EEPROM_MAX_RETRY_SPI);
+
+ /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and
+ * only 0-5mSec on 5V devices)
+ */
+ if (retry_count >= EEPROM_MAX_RETRY_SPI) {
+ DEBUGOUT("SPI EEPROM Status error\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_read_eeprom - Reads a 16 bit word from the EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset of word in the EEPROM to read
+ * @data: word read from the EEPROM
+ * @words: number of words to read
+ */
+s32 e1000_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ s32 ret;
+ spin_lock(&e1000_eeprom_lock);
+ ret = e1000_do_read_eeprom(hw, offset, words, data);
+ spin_unlock(&e1000_eeprom_lock);
+ return ret;
+}
+
+static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 i = 0;
+
+ DEBUGFUNC("e1000_read_eeprom");
+
+ /* If eeprom is not yet detected, do so now */
+ if (eeprom->word_size == 0)
+ e1000_init_eeprom_params(hw);
+
+ /* A check for invalid values: offset too large, too many words, and not
+ * enough words.
+ */
+ if ((offset >= eeprom->word_size)
+ || (words > eeprom->word_size - offset) || (words == 0)) {
+ DEBUGOUT2
+ ("\"words\" parameter out of bounds. Words = %d, size = %d\n",
+ offset, eeprom->word_size);
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* EEPROM's that don't use EERD to read require us to bit-bang the SPI
+ * directly. In this case, we need to acquire the EEPROM so that
+ * FW or other port software does not interrupt.
+ */
+ /* Prepare the EEPROM for bit-bang reading */
+ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+
+ /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have
+ * acquired the EEPROM at this point, so any returns should release it */
+ if (eeprom->type == e1000_eeprom_spi) {
+ u16 word_in;
+ u8 read_opcode = EEPROM_READ_OPCODE_SPI;
+
+ if (e1000_spi_eeprom_ready(hw)) {
+ e1000_release_eeprom(hw);
+ return -E1000_ERR_EEPROM;
+ }
+
+ e1000_standby_eeprom(hw);
+
+ /* Some SPI eeproms use the 8th address bit embedded in the opcode */
+ if ((eeprom->address_bits == 8) && (offset >= 128))
+ read_opcode |= EEPROM_A8_OPCODE_SPI;
+
+ /* Send the READ command (opcode + addr) */
+ e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits);
+ e1000_shift_out_ee_bits(hw, (u16) (offset * 2),
+ eeprom->address_bits);
+
+ /* Read the data. The address of the eeprom internally increments with
+ * each byte (spi) being read, saving on the overhead of eeprom setup
+ * and tear-down. The address counter will roll over if reading beyond
+ * the size of the eeprom, thus allowing the entire memory to be read
+ * starting from any offset. */
+ for (i = 0; i < words; i++) {
+ word_in = e1000_shift_in_ee_bits(hw, 16);
+ data[i] = (word_in >> 8) | (word_in << 8);
+ }
+ } else if (eeprom->type == e1000_eeprom_microwire) {
+ for (i = 0; i < words; i++) {
+ /* Send the READ command (opcode + addr) */
+ e1000_shift_out_ee_bits(hw,
+ EEPROM_READ_OPCODE_MICROWIRE,
+ eeprom->opcode_bits);
+ e1000_shift_out_ee_bits(hw, (u16) (offset + i),
+ eeprom->address_bits);
+
+ /* Read the data. For microwire, each word requires the overhead
+ * of eeprom setup and tear-down. */
+ data[i] = e1000_shift_in_ee_bits(hw, 16);
+ e1000_standby_eeprom(hw);
+ }
+ }
+
+ /* End this read operation */
+ e1000_release_eeprom(hw);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_validate_eeprom_checksum - Verifies that the EEPROM has a valid checksum
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Reads the first 64 16 bit words of the EEPROM and sums the values read.
+ * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is
+ * valid.
+ */
+s32 e1000_validate_eeprom_checksum(struct e1000_hw *hw)
+{
+ u16 checksum = 0;
+ u16 i, eeprom_data;
+
+ DEBUGFUNC("e1000_validate_eeprom_checksum");
+
+ for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
+ if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ checksum += eeprom_data;
+ }
+
+ if (checksum == (u16) EEPROM_SUM)
+ return E1000_SUCCESS;
+ else {
+ DEBUGOUT("EEPROM Checksum Invalid\n");
+ return -E1000_ERR_EEPROM;
+ }
+}
+
+/**
+ * e1000_update_eeprom_checksum - Calculates/writes the EEPROM checksum
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Sums the first 63 16 bit words of the EEPROM. Subtracts the sum from 0xBABA.
+ * Writes the difference to word offset 63 of the EEPROM.
+ */
+s32 e1000_update_eeprom_checksum(struct e1000_hw *hw)
+{
+ u16 checksum = 0;
+ u16 i, eeprom_data;
+
+ DEBUGFUNC("e1000_update_eeprom_checksum");
+
+ for (i = 0; i < EEPROM_CHECKSUM_REG; i++) {
+ if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ checksum += eeprom_data;
+ }
+ checksum = (u16) EEPROM_SUM - checksum;
+ if (e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) {
+ DEBUGOUT("EEPROM Write Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_write_eeprom - write words to the different EEPROM types.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: 16 bit word to be written to the EEPROM
+ *
+ * If e1000_update_eeprom_checksum is not called after this function, the
+ * EEPROM will most likely contain an invalid checksum.
+ */
+s32 e1000_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ s32 ret;
+ spin_lock(&e1000_eeprom_lock);
+ ret = e1000_do_write_eeprom(hw, offset, words, data);
+ spin_unlock(&e1000_eeprom_lock);
+ return ret;
+}
+
+static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ s32 status = 0;
+
+ DEBUGFUNC("e1000_write_eeprom");
+
+ /* If eeprom is not yet detected, do so now */
+ if (eeprom->word_size == 0)
+ e1000_init_eeprom_params(hw);
+
+ /* A check for invalid values: offset too large, too many words, and not
+ * enough words.
+ */
+ if ((offset >= eeprom->word_size)
+ || (words > eeprom->word_size - offset) || (words == 0)) {
+ DEBUGOUT("\"words\" parameter out of bounds\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* Prepare the EEPROM for writing */
+ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+
+ if (eeprom->type == e1000_eeprom_microwire) {
+ status = e1000_write_eeprom_microwire(hw, offset, words, data);
+ } else {
+ status = e1000_write_eeprom_spi(hw, offset, words, data);
+ msleep(10);
+ }
+
+ /* Done with writing */
+ e1000_release_eeprom(hw);
+
+ return status;
+}
+
+/**
+ * e1000_write_eeprom_spi - Writes a 16 bit word to a given offset in an SPI EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: pointer to array of 8 bit words to be written to the EEPROM
+ */
+static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u16 widx = 0;
+
+ DEBUGFUNC("e1000_write_eeprom_spi");
+
+ while (widx < words) {
+ u8 write_opcode = EEPROM_WRITE_OPCODE_SPI;
+
+ if (e1000_spi_eeprom_ready(hw))
+ return -E1000_ERR_EEPROM;
+
+ e1000_standby_eeprom(hw);
+
+ /* Send the WRITE ENABLE command (8 bit opcode ) */
+ e1000_shift_out_ee_bits(hw, EEPROM_WREN_OPCODE_SPI,
+ eeprom->opcode_bits);
+
+ e1000_standby_eeprom(hw);
+
+ /* Some SPI eeproms use the 8th address bit embedded in the opcode */
+ if ((eeprom->address_bits == 8) && (offset >= 128))
+ write_opcode |= EEPROM_A8_OPCODE_SPI;
+
+ /* Send the Write command (8-bit opcode + addr) */
+ e1000_shift_out_ee_bits(hw, write_opcode, eeprom->opcode_bits);
+
+ e1000_shift_out_ee_bits(hw, (u16) ((offset + widx) * 2),
+ eeprom->address_bits);
+
+ /* Send the data */
+
+ /* Loop to allow for up to whole page write (32 bytes) of eeprom */
+ while (widx < words) {
+ u16 word_out = data[widx];
+ word_out = (word_out >> 8) | (word_out << 8);
+ e1000_shift_out_ee_bits(hw, word_out, 16);
+ widx++;
+
+ /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE
+ * operation, while the smaller eeproms are capable of an 8-byte
+ * PAGE WRITE operation. Break the inner loop to pass new address
+ */
+ if ((((offset + widx) * 2) % eeprom->page_size) == 0) {
+ e1000_standby_eeprom(hw);
+ break;
+ }
+ }
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_write_eeprom_microwire - Writes a 16 bit word to a given offset in a Microwire EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: pointer to array of 8 bit words to be written to the EEPROM
+ */
+static s32 e1000_write_eeprom_microwire(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd;
+ u16 words_written = 0;
+ u16 i = 0;
+
+ DEBUGFUNC("e1000_write_eeprom_microwire");
+
+ /* Send the write enable command to the EEPROM (3-bit opcode plus
+ * 6/8-bit dummy address beginning with 11). It's less work to include
+ * the 11 of the dummy address as part of the opcode than it is to shift
+ * it over the correct number of bits for the address. This puts the
+ * EEPROM into write/erase mode.
+ */
+ e1000_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE_MICROWIRE,
+ (u16) (eeprom->opcode_bits + 2));
+
+ e1000_shift_out_ee_bits(hw, 0, (u16) (eeprom->address_bits - 2));
+
+ /* Prepare the EEPROM */
+ e1000_standby_eeprom(hw);
+
+ while (words_written < words) {
+ /* Send the Write command (3-bit opcode + addr) */
+ e1000_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE_MICROWIRE,
+ eeprom->opcode_bits);
+
+ e1000_shift_out_ee_bits(hw, (u16) (offset + words_written),
+ eeprom->address_bits);
+
+ /* Send the data */
+ e1000_shift_out_ee_bits(hw, data[words_written], 16);
+
+ /* Toggle the CS line. This in effect tells the EEPROM to execute
+ * the previous command.
+ */
+ e1000_standby_eeprom(hw);
+
+ /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will
+ * signal that the command has been completed by raising the DO signal.
+ * If DO does not go high in 10 milliseconds, then error out.
+ */
+ for (i = 0; i < 200; i++) {
+ eecd = er32(EECD);
+ if (eecd & E1000_EECD_DO)
+ break;
+ udelay(50);
+ }
+ if (i == 200) {
+ DEBUGOUT("EEPROM Write did not complete\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* Recover from write */
+ e1000_standby_eeprom(hw);
+
+ words_written++;
+ }
+
+ /* Send the write disable command to the EEPROM (3-bit opcode plus
+ * 6/8-bit dummy address beginning with 10). It's less work to include
+ * the 10 of the dummy address as part of the opcode than it is to shift
+ * it over the correct number of bits for the address. This takes the
+ * EEPROM out of write/erase mode.
+ */
+ e1000_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE_MICROWIRE,
+ (u16) (eeprom->opcode_bits + 2));
+
+ e1000_shift_out_ee_bits(hw, 0, (u16) (eeprom->address_bits - 2));
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_read_mac_addr - read the adapters MAC from eeprom
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
+ * second function of dual function devices
+ */
+s32 e1000_read_mac_addr(struct e1000_hw *hw)
+{
+ u16 offset;
+ u16 eeprom_data, i;
+
+ DEBUGFUNC("e1000_read_mac_addr");
+
+ for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
+ offset = i >> 1;
+ if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ hw->perm_mac_addr[i] = (u8) (eeprom_data & 0x00FF);
+ hw->perm_mac_addr[i + 1] = (u8) (eeprom_data >> 8);
+ }
+
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ if (er32(STATUS) & E1000_STATUS_FUNC_1)
+ hw->perm_mac_addr[5] ^= 0x01;
+ break;
+ }
+
+ for (i = 0; i < NODE_ADDRESS_SIZE; i++)
+ hw->mac_addr[i] = hw->perm_mac_addr[i];
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_init_rx_addrs - Initializes receive address filters.
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Places the MAC address in receive address register 0 and clears the rest
+ * of the receive address registers. Clears the multicast table. Assumes
+ * the receiver is in reset when the routine is called.
+ */
+static void e1000_init_rx_addrs(struct e1000_hw *hw)
+{
+ u32 i;
+ u32 rar_num;
+
+ DEBUGFUNC("e1000_init_rx_addrs");
+
+ /* Setup the receive address. */
+ DEBUGOUT("Programming MAC Address into RAR[0]\n");
+
+ e1000_rar_set(hw, hw->mac_addr, 0);
+
+ rar_num = E1000_RAR_ENTRIES;
+
+ /* Zero out the other 15 receive addresses. */
+ DEBUGOUT("Clearing RAR[1-15]\n");
+ for (i = 1; i < rar_num; i++) {
+ E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
+ E1000_WRITE_FLUSH();
+ E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
+ E1000_WRITE_FLUSH();
+ }
+}
+
+/**
+ * e1000_hash_mc_addr - Hashes an address to determine its location in the multicast table
+ * @hw: Struct containing variables accessed by shared code
+ * @mc_addr: the multicast address to hash
+ */
+u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
+{
+ u32 hash_value = 0;
+
+ /* The portion of the address that is used for the hash table is
+ * determined by the mc_filter_type setting.
+ */
+ switch (hw->mc_filter_type) {
+ /* [0] [1] [2] [3] [4] [5]
+ * 01 AA 00 12 34 56
+ * LSB MSB
+ */
+ case 0:
+ /* [47:36] i.e. 0x563 for above example address */
+ hash_value = ((mc_addr[4] >> 4) | (((u16) mc_addr[5]) << 4));
+ break;
+ case 1:
+ /* [46:35] i.e. 0xAC6 for above example address */
+ hash_value = ((mc_addr[4] >> 3) | (((u16) mc_addr[5]) << 5));
+ break;
+ case 2:
+ /* [45:34] i.e. 0x5D8 for above example address */
+ hash_value = ((mc_addr[4] >> 2) | (((u16) mc_addr[5]) << 6));
+ break;
+ case 3:
+ /* [43:32] i.e. 0x634 for above example address */
+ hash_value = ((mc_addr[4]) | (((u16) mc_addr[5]) << 8));
+ break;
+ }
+
+ hash_value &= 0xFFF;
+ return hash_value;
+}
+
+/**
+ * e1000_rar_set - Puts an ethernet address into a receive address register.
+ * @hw: Struct containing variables accessed by shared code
+ * @addr: Address to put into receive address register
+ * @index: Receive address register to write
+ */
+void e1000_rar_set(struct e1000_hw *hw, u8 *addr, u32 index)
+{
+ u32 rar_low, rar_high;
+
+ /* HW expects these in little endian so we reverse the byte order
+ * from network order (big endian) to little endian
+ */
+ rar_low = ((u32) addr[0] | ((u32) addr[1] << 8) |
+ ((u32) addr[2] << 16) | ((u32) addr[3] << 24));
+ rar_high = ((u32) addr[4] | ((u32) addr[5] << 8));
+
+ /* Disable Rx and flush all Rx frames before enabling RSS to avoid Rx
+ * unit hang.
+ *
+ * Description:
+ * If there are any Rx frames queued up or otherwise present in the HW
+ * before RSS is enabled, and then we enable RSS, the HW Rx unit will
+ * hang. To work around this issue, we have to disable receives and
+ * flush out all Rx frames before we enable RSS. To do so, we modify we
+ * redirect all Rx traffic to manageability and then reset the HW.
+ * This flushes away Rx frames, and (since the redirections to
+ * manageability persists across resets) keeps new ones from coming in
+ * while we work. Then, we clear the Address Valid AV bit for all MAC
+ * addresses and undo the re-direction to manageability.
+ * Now, frames are coming in again, but the MAC won't accept them, so
+ * far so good. We now proceed to initialize RSS (if necessary) and
+ * configure the Rx unit. Last, we re-enable the AV bits and continue
+ * on our merry way.
+ */
+ switch (hw->mac_type) {
+ default:
+ /* Indicate to hardware the Address is Valid. */
+ rar_high |= E1000_RAH_AV;
+ break;
+ }
+
+ E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low);
+ E1000_WRITE_FLUSH();
+ E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high);
+ E1000_WRITE_FLUSH();
+}
+
+/**
+ * e1000_write_vfta - Writes a value to the specified offset in the VLAN filter table.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: Offset in VLAN filer table to write
+ * @value: Value to write into VLAN filter table
+ */
+void e1000_write_vfta(struct e1000_hw *hw, u32 offset, u32 value)
+{
+ u32 temp;
+
+ if ((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) {
+ temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1));
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
+ E1000_WRITE_FLUSH();
+ E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp);
+ E1000_WRITE_FLUSH();
+ } else {
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
+ E1000_WRITE_FLUSH();
+ }
+}
+
+/**
+ * e1000_clear_vfta - Clears the VLAN filer table
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_clear_vfta(struct e1000_hw *hw)
+{
+ u32 offset;
+ u32 vfta_value = 0;
+ u32 vfta_offset = 0;
+ u32 vfta_bit_in_reg = 0;
+
+ for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+ /* If the offset we want to clear is the same offset of the
+ * manageability VLAN ID, then clear all bits except that of the
+ * manageability unit */
+ vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value);
+ E1000_WRITE_FLUSH();
+ }
+}
+
+static s32 e1000_id_led_init(struct e1000_hw *hw)
+{
+ u32 ledctl;
+ const u32 ledctl_mask = 0x000000FF;
+ const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON;
+ const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF;
+ u16 eeprom_data, i, temp;
+ const u16 led_mask = 0x0F;
+
+ DEBUGFUNC("e1000_id_led_init");
+
+ if (hw->mac_type < e1000_82540) {
+ /* Nothing to do */
+ return E1000_SUCCESS;
+ }
+
+ ledctl = er32(LEDCTL);
+ hw->ledctl_default = ledctl;
+ hw->ledctl_mode1 = hw->ledctl_default;
+ hw->ledctl_mode2 = hw->ledctl_default;
+
+ if (e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ if ((eeprom_data == ID_LED_RESERVED_0000) ||
+ (eeprom_data == ID_LED_RESERVED_FFFF)) {
+ eeprom_data = ID_LED_DEFAULT;
+ }
+
+ for (i = 0; i < 4; i++) {
+ temp = (eeprom_data >> (i << 2)) & led_mask;
+ switch (temp) {
+ case ID_LED_ON1_DEF2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_ON1_OFF2:
+ hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode1 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_OFF1_DEF2:
+ case ID_LED_OFF1_ON2:
+ case ID_LED_OFF1_OFF2:
+ hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode1 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ switch (temp) {
+ case ID_LED_DEF1_ON2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_OFF1_ON2:
+ hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode2 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_DEF1_OFF2:
+ case ID_LED_ON1_OFF2:
+ case ID_LED_OFF1_OFF2:
+ hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode2 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_setup_led
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Prepares SW controlable LED for use and saves the current state of the LED.
+ */
+s32 e1000_setup_led(struct e1000_hw *hw)
+{
+ u32 ledctl;
+ s32 ret_val = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_setup_led");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ /* No setup necessary */
+ break;
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ /* Turn off PHY Smart Power Down (if enabled) */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ &hw->phy_spd_default);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ (u16) (hw->phy_spd_default &
+ ~IGP01E1000_GMII_SPD));
+ if (ret_val)
+ return ret_val;
+ /* Fall Through */
+ default:
+ if (hw->media_type == e1000_media_type_fiber) {
+ ledctl = er32(LEDCTL);
+ /* Save current LEDCTL settings */
+ hw->ledctl_default = ledctl;
+ /* Turn off LED0 */
+ ledctl &= ~(E1000_LEDCTL_LED0_IVRT |
+ E1000_LEDCTL_LED0_BLINK |
+ E1000_LEDCTL_LED0_MODE_MASK);
+ ledctl |= (E1000_LEDCTL_MODE_LED_OFF <<
+ E1000_LEDCTL_LED0_MODE_SHIFT);
+ ew32(LEDCTL, ledctl);
+ } else if (hw->media_type == e1000_media_type_copper)
+ ew32(LEDCTL, hw->ledctl_mode1);
+ break;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_cleanup_led - Restores the saved state of the SW controlable LED.
+ * @hw: Struct containing variables accessed by shared code
+ */
+s32 e1000_cleanup_led(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_cleanup_led");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ /* No cleanup necessary */
+ break;
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ /* Turn on PHY Smart Power Down (if previously enabled) */
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ hw->phy_spd_default);
+ if (ret_val)
+ return ret_val;
+ /* Fall Through */
+ default:
+ /* Restore LEDCTL settings */
+ ew32(LEDCTL, hw->ledctl_default);
+ break;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_led_on - Turns on the software controllable LED
+ * @hw: Struct containing variables accessed by shared code
+ */
+s32 e1000_led_on(struct e1000_hw *hw)
+{
+ u32 ctrl = er32(CTRL);
+
+ DEBUGFUNC("e1000_led_on");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ /* Set SW Defineable Pin 0 to turn on the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ break;
+ case e1000_82544:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Set SW Defineable Pin 0 to turn on the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else {
+ /* Clear SW Defineable Pin 0 to turn on the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ }
+ break;
+ default:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Clear SW Defineable Pin 0 to turn on the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else if (hw->media_type == e1000_media_type_copper) {
+ ew32(LEDCTL, hw->ledctl_mode2);
+ return E1000_SUCCESS;
+ }
+ break;
+ }
+
+ ew32(CTRL, ctrl);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_led_off - Turns off the software controllable LED
+ * @hw: Struct containing variables accessed by shared code
+ */
+s32 e1000_led_off(struct e1000_hw *hw)
+{
+ u32 ctrl = er32(CTRL);
+
+ DEBUGFUNC("e1000_led_off");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ /* Clear SW Defineable Pin 0 to turn off the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ break;
+ case e1000_82544:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Clear SW Defineable Pin 0 to turn off the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else {
+ /* Set SW Defineable Pin 0 to turn off the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ }
+ break;
+ default:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Set SW Defineable Pin 0 to turn off the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else if (hw->media_type == e1000_media_type_copper) {
+ ew32(LEDCTL, hw->ledctl_mode1);
+ return E1000_SUCCESS;
+ }
+ break;
+ }
+
+ ew32(CTRL, ctrl);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_clear_hw_cntrs - Clears all hardware statistics counters.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_clear_hw_cntrs(struct e1000_hw *hw)
+{
+ volatile u32 temp;
+
+ temp = er32(CRCERRS);
+ temp = er32(SYMERRS);
+ temp = er32(MPC);
+ temp = er32(SCC);
+ temp = er32(ECOL);
+ temp = er32(MCC);
+ temp = er32(LATECOL);
+ temp = er32(COLC);
+ temp = er32(DC);
+ temp = er32(SEC);
+ temp = er32(RLEC);
+ temp = er32(XONRXC);
+ temp = er32(XONTXC);
+ temp = er32(XOFFRXC);
+ temp = er32(XOFFTXC);
+ temp = er32(FCRUC);
+
+ temp = er32(PRC64);
+ temp = er32(PRC127);
+ temp = er32(PRC255);
+ temp = er32(PRC511);
+ temp = er32(PRC1023);
+ temp = er32(PRC1522);
+
+ temp = er32(GPRC);
+ temp = er32(BPRC);
+ temp = er32(MPRC);
+ temp = er32(GPTC);
+ temp = er32(GORCL);
+ temp = er32(GORCH);
+ temp = er32(GOTCL);
+ temp = er32(GOTCH);
+ temp = er32(RNBC);
+ temp = er32(RUC);
+ temp = er32(RFC);
+ temp = er32(ROC);
+ temp = er32(RJC);
+ temp = er32(TORL);
+ temp = er32(TORH);
+ temp = er32(TOTL);
+ temp = er32(TOTH);
+ temp = er32(TPR);
+ temp = er32(TPT);
+
+ temp = er32(PTC64);
+ temp = er32(PTC127);
+ temp = er32(PTC255);
+ temp = er32(PTC511);
+ temp = er32(PTC1023);
+ temp = er32(PTC1522);
+
+ temp = er32(MPTC);
+ temp = er32(BPTC);
+
+ if (hw->mac_type < e1000_82543)
+ return;
+
+ temp = er32(ALGNERRC);
+ temp = er32(RXERRC);
+ temp = er32(TNCRS);
+ temp = er32(CEXTERR);
+ temp = er32(TSCTC);
+ temp = er32(TSCTFC);
+
+ if (hw->mac_type <= e1000_82544)
+ return;
+
+ temp = er32(MGTPRC);
+ temp = er32(MGTPDC);
+ temp = er32(MGTPTC);
+}
+
+/**
+ * e1000_reset_adaptive - Resets Adaptive IFS to its default state.
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Call this after e1000_init_hw. You may override the IFS defaults by setting
+ * hw->ifs_params_forced to true. However, you must initialize hw->
+ * current_ifs_val, ifs_min_val, ifs_max_val, ifs_step_size, and ifs_ratio
+ * before calling this function.
+ */
+void e1000_reset_adaptive(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_reset_adaptive");
+
+ if (hw->adaptive_ifs) {
+ if (!hw->ifs_params_forced) {
+ hw->current_ifs_val = 0;
+ hw->ifs_min_val = IFS_MIN;
+ hw->ifs_max_val = IFS_MAX;
+ hw->ifs_step_size = IFS_STEP;
+ hw->ifs_ratio = IFS_RATIO;
+ }
+ hw->in_ifs_mode = false;
+ ew32(AIT, 0);
+ } else {
+ DEBUGOUT("Not in Adaptive IFS mode!\n");
+ }
+}
+
+/**
+ * e1000_update_adaptive - update adaptive IFS
+ * @hw: Struct containing variables accessed by shared code
+ * @tx_packets: Number of transmits since last callback
+ * @total_collisions: Number of collisions since last callback
+ *
+ * Called during the callback/watchdog routine to update IFS value based on
+ * the ratio of transmits to collisions.
+ */
+void e1000_update_adaptive(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_update_adaptive");
+
+ if (hw->adaptive_ifs) {
+ if ((hw->collision_delta *hw->ifs_ratio) > hw->tx_packet_delta) {
+ if (hw->tx_packet_delta > MIN_NUM_XMITS) {
+ hw->in_ifs_mode = true;
+ if (hw->current_ifs_val < hw->ifs_max_val) {
+ if (hw->current_ifs_val == 0)
+ hw->current_ifs_val =
+ hw->ifs_min_val;
+ else
+ hw->current_ifs_val +=
+ hw->ifs_step_size;
+ ew32(AIT, hw->current_ifs_val);
+ }
+ }
+ } else {
+ if (hw->in_ifs_mode
+ && (hw->tx_packet_delta <= MIN_NUM_XMITS)) {
+ hw->current_ifs_val = 0;
+ hw->in_ifs_mode = false;
+ ew32(AIT, 0);
+ }
+ }
+ } else {
+ DEBUGOUT("Not in Adaptive IFS mode!\n");
+ }
+}
+
+/**
+ * e1000_tbi_adjust_stats
+ * @hw: Struct containing variables accessed by shared code
+ * @frame_len: The length of the frame in question
+ * @mac_addr: The Ethernet destination address of the frame in question
+ *
+ * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT
+ */
+void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats,
+ u32 frame_len, u8 *mac_addr)
+{
+ u64 carry_bit;
+
+ /* First adjust the frame length. */
+ frame_len--;
+ /* We need to adjust the statistics counters, since the hardware
+ * counters overcount this packet as a CRC error and undercount
+ * the packet as a good packet
+ */
+ /* This packet should not be counted as a CRC error. */
+ stats->crcerrs--;
+ /* This packet does count as a Good Packet Received. */
+ stats->gprc++;
+
+ /* Adjust the Good Octets received counters */
+ carry_bit = 0x80000000 & stats->gorcl;
+ stats->gorcl += frame_len;
+ /* If the high bit of Gorcl (the low 32 bits of the Good Octets
+ * Received Count) was one before the addition,
+ * AND it is zero after, then we lost the carry out,
+ * need to add one to Gorch (Good Octets Received Count High).
+ * This could be simplified if all environments supported
+ * 64-bit integers.
+ */
+ if (carry_bit && ((stats->gorcl & 0x80000000) == 0))
+ stats->gorch++;
+ /* Is this a broadcast or multicast? Check broadcast first,
+ * since the test for a multicast frame will test positive on
+ * a broadcast frame.
+ */
+ if ((mac_addr[0] == (u8) 0xff) && (mac_addr[1] == (u8) 0xff))
+ /* Broadcast packet */
+ stats->bprc++;
+ else if (*mac_addr & 0x01)
+ /* Multicast packet */
+ stats->mprc++;
+
+ if (frame_len == hw->max_frame_size) {
+ /* In this case, the hardware has overcounted the number of
+ * oversize frames.
+ */
+ if (stats->roc > 0)
+ stats->roc--;
+ }
+
+ /* Adjust the bin counters when the extra byte put the frame in the
+ * wrong bin. Remember that the frame_len was adjusted above.
+ */
+ if (frame_len == 64) {
+ stats->prc64++;
+ stats->prc127--;
+ } else if (frame_len == 127) {
+ stats->prc127++;
+ stats->prc255--;
+ } else if (frame_len == 255) {
+ stats->prc255++;
+ stats->prc511--;
+ } else if (frame_len == 511) {
+ stats->prc511++;
+ stats->prc1023--;
+ } else if (frame_len == 1023) {
+ stats->prc1023++;
+ stats->prc1522--;
+ } else if (frame_len == 1522) {
+ stats->prc1522++;
+ }
+}
+
+/**
+ * e1000_get_bus_info
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Gets the current PCI bus type, speed, and width of the hardware
+ */
+void e1000_get_bus_info(struct e1000_hw *hw)
+{
+ u32 status;
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ hw->bus_type = e1000_bus_type_pci;
+ hw->bus_speed = e1000_bus_speed_unknown;
+ hw->bus_width = e1000_bus_width_unknown;
+ break;
+ default:
+ status = er32(STATUS);
+ hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ?
+ e1000_bus_type_pcix : e1000_bus_type_pci;
+
+ if (hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) {
+ hw->bus_speed = (hw->bus_type == e1000_bus_type_pci) ?
+ e1000_bus_speed_66 : e1000_bus_speed_120;
+ } else if (hw->bus_type == e1000_bus_type_pci) {
+ hw->bus_speed = (status & E1000_STATUS_PCI66) ?
+ e1000_bus_speed_66 : e1000_bus_speed_33;
+ } else {
+ switch (status & E1000_STATUS_PCIX_SPEED) {
+ case E1000_STATUS_PCIX_SPEED_66:
+ hw->bus_speed = e1000_bus_speed_66;
+ break;
+ case E1000_STATUS_PCIX_SPEED_100:
+ hw->bus_speed = e1000_bus_speed_100;
+ break;
+ case E1000_STATUS_PCIX_SPEED_133:
+ hw->bus_speed = e1000_bus_speed_133;
+ break;
+ default:
+ hw->bus_speed = e1000_bus_speed_reserved;
+ break;
+ }
+ }
+ hw->bus_width = (status & E1000_STATUS_BUS64) ?
+ e1000_bus_width_64 : e1000_bus_width_32;
+ break;
+ }
+}
+
+/**
+ * e1000_write_reg_io
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset to write to
+ * @value: value to write
+ *
+ * Writes a value to one of the devices registers using port I/O (as opposed to
+ * memory mapped I/O). Only 82544 and newer devices support port I/O.
+ */
+static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value)
+{
+ unsigned long io_addr = hw->io_base;
+ unsigned long io_data = hw->io_base + 4;
+
+ e1000_io_write(hw, io_addr, offset);
+ e1000_io_write(hw, io_data, value);
+}
+
+/**
+ * e1000_get_cable_length - Estimates the cable length.
+ * @hw: Struct containing variables accessed by shared code
+ * @min_length: The estimated minimum length
+ * @max_length: The estimated maximum length
+ *
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
+ *
+ * This function always returns a ranged length (minimum & maximum).
+ * So for M88 phy's, this function interprets the one value returned from the
+ * register to the minimum and maximum range.
+ * For IGP phy's, the function calculates the range by the AGC registers.
+ */
+static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length,
+ u16 *max_length)
+{
+ s32 ret_val;
+ u16 agc_value = 0;
+ u16 i, phy_data;
+ u16 cable_length;
+
+ DEBUGFUNC("e1000_get_cable_length");
+
+ *min_length = *max_length = 0;
+
+ /* Use old method for Phy older than IGP */
+ if (hw->phy_type == e1000_phy_m88) {
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ cable_length = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT;
+
+ /* Convert the enum value to ranged values */
+ switch (cable_length) {
+ case e1000_cable_length_50:
+ *min_length = 0;
+ *max_length = e1000_igp_cable_length_50;
+ break;
+ case e1000_cable_length_50_80:
+ *min_length = e1000_igp_cable_length_50;
+ *max_length = e1000_igp_cable_length_80;
+ break;
+ case e1000_cable_length_80_110:
+ *min_length = e1000_igp_cable_length_80;
+ *max_length = e1000_igp_cable_length_110;
+ break;
+ case e1000_cable_length_110_140:
+ *min_length = e1000_igp_cable_length_110;
+ *max_length = e1000_igp_cable_length_140;
+ break;
+ case e1000_cable_length_140:
+ *min_length = e1000_igp_cable_length_140;
+ *max_length = e1000_igp_cable_length_170;
+ break;
+ default:
+ return -E1000_ERR_PHY;
+ break;
+ }
+ } else if (hw->phy_type == e1000_phy_igp) { /* For IGP PHY */
+ u16 cur_agc_value;
+ u16 min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
+ u16 agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
+ { IGP01E1000_PHY_AGC_A,
+ IGP01E1000_PHY_AGC_B,
+ IGP01E1000_PHY_AGC_C,
+ IGP01E1000_PHY_AGC_D
+ };
+ /* Read the AGC registers for all channels */
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+
+ ret_val =
+ e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT;
+
+ /* Value bound check. */
+ if ((cur_agc_value >=
+ IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1)
+ || (cur_agc_value == 0))
+ return -E1000_ERR_PHY;
+
+ agc_value += cur_agc_value;
+
+ /* Update minimal AGC value. */
+ if (min_agc_value > cur_agc_value)
+ min_agc_value = cur_agc_value;
+ }
+
+ /* Remove the minimal AGC result for length < 50m */
+ if (agc_value <
+ IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) {
+ agc_value -= min_agc_value;
+
+ /* Get the average length of the remaining 3 channels */
+ agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1);
+ } else {
+ /* Get the average length of all the 4 channels. */
+ agc_value /= IGP01E1000_PHY_CHANNEL_NUM;
+ }
+
+ /* Set the range of the calculated length. */
+ *min_length = ((e1000_igp_cable_length_table[agc_value] -
+ IGP01E1000_AGC_RANGE) > 0) ?
+ (e1000_igp_cable_length_table[agc_value] -
+ IGP01E1000_AGC_RANGE) : 0;
+ *max_length = e1000_igp_cable_length_table[agc_value] +
+ IGP01E1000_AGC_RANGE;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_check_polarity - Check the cable polarity
+ * @hw: Struct containing variables accessed by shared code
+ * @polarity: output parameter : 0 - Polarity is not reversed
+ * 1 - Polarity is reversed.
+ *
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
+ *
+ * For phy's older than IGP, this function simply reads the polarity bit in the
+ * Phy Status register. For IGP phy's, this bit is valid only if link speed is
+ * 10 Mbps. If the link speed is 100 Mbps there is no polarity so this bit will
+ * return 0. If the link speed is 1000 Mbps the polarity status is in the
+ * IGP01E1000_PHY_PCS_INIT_REG.
+ */
+static s32 e1000_check_polarity(struct e1000_hw *hw,
+ e1000_rev_polarity *polarity)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_check_polarity");
+
+ if (hw->phy_type == e1000_phy_m88) {
+ /* return the Polarity bit in the Status register. */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ *polarity = ((phy_data & M88E1000_PSSR_REV_POLARITY) >>
+ M88E1000_PSSR_REV_POLARITY_SHIFT) ?
+ e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
+
+ } else if (hw->phy_type == e1000_phy_igp) {
+ /* Read the Status register to check the speed */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to
+ * find the polarity status */
+ if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+
+ /* Read the GIG initialization PCS register (0x00B4) */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Check the polarity bits */
+ *polarity = (phy_data & IGP01E1000_PHY_POLARITY_MASK) ?
+ e1000_rev_polarity_reversed :
+ e1000_rev_polarity_normal;
+ } else {
+ /* For 10 Mbps, read the polarity bit in the status register. (for
+ * 100 Mbps this bit is always 0) */
+ *polarity =
+ (phy_data & IGP01E1000_PSSR_POLARITY_REVERSED) ?
+ e1000_rev_polarity_reversed :
+ e1000_rev_polarity_normal;
+ }
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_check_downshift - Check if Downshift occurred
+ * @hw: Struct containing variables accessed by shared code
+ * @downshift: output parameter : 0 - No Downshift occurred.
+ * 1 - Downshift occurred.
+ *
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
+ *
+ * For phy's older than IGP, this function reads the Downshift bit in the Phy
+ * Specific Status register. For IGP phy's, it reads the Downgrade bit in the
+ * Link Health register. In IGP this bit is latched high, so the driver must
+ * read it immediately after link is established.
+ */
+static s32 e1000_check_downshift(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_check_downshift");
+
+ if (hw->phy_type == e1000_phy_igp) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ hw->speed_downgraded =
+ (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0;
+ } else if (hw->phy_type == e1000_phy_m88) {
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >>
+ M88E1000_PSSR_DOWNSHIFT_SHIFT;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_config_dsp_after_link_change
+ * @hw: Struct containing variables accessed by shared code
+ * @link_up: was link up at the time this was called
+ *
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * E1000_SUCCESS at any other case.
+ *
+ * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a
+ * gigabit link is achieved to improve link quality.
+ */
+
+static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up)
+{
+ s32 ret_val;
+ u16 phy_data, phy_saved_data, speed, duplex, i;
+ u16 dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
+ { IGP01E1000_PHY_AGC_PARAM_A,
+ IGP01E1000_PHY_AGC_PARAM_B,
+ IGP01E1000_PHY_AGC_PARAM_C,
+ IGP01E1000_PHY_AGC_PARAM_D
+ };
+ u16 min_length, max_length;
+
+ DEBUGFUNC("e1000_config_dsp_after_link_change");
+
+ if (hw->phy_type != e1000_phy_igp)
+ return E1000_SUCCESS;
+
+ if (link_up) {
+ ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if (ret_val) {
+ DEBUGOUT("Error getting link speed and duplex\n");
+ return ret_val;
+ }
+
+ if (speed == SPEED_1000) {
+
+ ret_val =
+ e1000_get_cable_length(hw, &min_length,
+ &max_length);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->dsp_config_state == e1000_dsp_config_enabled)
+ && min_length >= e1000_igp_cable_length_50) {
+
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val =
+ e1000_read_phy_reg(hw,
+ dsp_reg_array[i],
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &=
+ ~IGP01E1000_PHY_EDAC_MU_INDEX;
+
+ ret_val =
+ e1000_write_phy_reg(hw,
+ dsp_reg_array
+ [i], phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ hw->dsp_config_state =
+ e1000_dsp_config_activated;
+ }
+
+ if ((hw->ffe_config_state == e1000_ffe_config_enabled)
+ && (min_length < e1000_igp_cable_length_50)) {
+
+ u16 ffe_idle_err_timeout =
+ FFE_IDLE_ERR_COUNT_TIMEOUT_20;
+ u32 idle_errs = 0;
+
+ /* clear previous idle error counts */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_1000T_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ for (i = 0; i < ffe_idle_err_timeout; i++) {
+ udelay(1000);
+ ret_val =
+ e1000_read_phy_reg(hw,
+ PHY_1000T_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ idle_errs +=
+ (phy_data &
+ SR_1000T_IDLE_ERROR_CNT);
+ if (idle_errs >
+ SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT)
+ {
+ hw->ffe_config_state =
+ e1000_ffe_config_active;
+
+ ret_val =
+ e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_DSP_FFE,
+ IGP01E1000_PHY_DSP_FFE_CM_CP);
+ if (ret_val)
+ return ret_val;
+ break;
+ }
+
+ if (idle_errs)
+ ffe_idle_err_timeout =
+ FFE_IDLE_ERR_COUNT_TIMEOUT_100;
+ }
+ }
+ }
+ } else {
+ if (hw->dsp_config_state == e1000_dsp_config_activated) {
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of the routines. */
+ ret_val =
+ e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
+
+ if (ret_val)
+ return ret_val;
+
+ /* Disable the PHY transmitter */
+ ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
+
+ if (ret_val)
+ return ret_val;
+
+ mdelay(20);
+
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_FORCE_GIGA);
+ if (ret_val)
+ return ret_val;
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val =
+ e1000_read_phy_reg(hw, dsp_reg_array[i],
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX;
+ phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS;
+
+ ret_val =
+ e1000_write_phy_reg(hw, dsp_reg_array[i],
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_RESTART_AUTONEG);
+ if (ret_val)
+ return ret_val;
+
+ mdelay(20);
+
+ /* Now enable the transmitter */
+ ret_val =
+ e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
+
+ if (ret_val)
+ return ret_val;
+
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+ }
+
+ if (hw->ffe_config_state == e1000_ffe_config_active) {
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of the routines. */
+ ret_val =
+ e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
+
+ if (ret_val)
+ return ret_val;
+
+ /* Disable the PHY transmitter */
+ ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
+
+ if (ret_val)
+ return ret_val;
+
+ mdelay(20);
+
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_FORCE_GIGA);
+ if (ret_val)
+ return ret_val;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_DSP_FFE,
+ IGP01E1000_PHY_DSP_FFE_DEFAULT);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_RESTART_AUTONEG);
+ if (ret_val)
+ return ret_val;
+
+ mdelay(20);
+
+ /* Now enable the transmitter */
+ ret_val =
+ e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
+
+ if (ret_val)
+ return ret_val;
+
+ hw->ffe_config_state = e1000_ffe_config_enabled;
+ }
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_set_phy_mode - Set PHY to class A mode
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Assumes the following operations will follow to enable the new class mode.
+ * 1. Do a PHY soft reset
+ * 2. Restart auto-negotiation or force link.
+ */
+static s32 e1000_set_phy_mode(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 eeprom_data;
+
+ DEBUGFUNC("e1000_set_phy_mode");
+
+ if ((hw->mac_type == e1000_82545_rev_3) &&
+ (hw->media_type == e1000_media_type_copper)) {
+ ret_val =
+ e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1,
+ &eeprom_data);
+ if (ret_val) {
+ return ret_val;
+ }
+
+ if ((eeprom_data != EEPROM_RESERVED_WORD) &&
+ (eeprom_data & EEPROM_PHY_CLASS_A)) {
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT,
+ 0x000B);
+ if (ret_val)
+ return ret_val;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL,
+ 0x8104);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy_reset_disable = false;
+ }
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_set_d3_lplu_state - set d3 link power state
+ * @hw: Struct containing variables accessed by shared code
+ * @active: true to enable lplu false to disable lplu.
+ *
+ * This function sets the lplu state according to the active flag. When
+ * activating lplu this function also disables smart speed and vise versa.
+ * lplu will not be activated unless the device autonegotiation advertisement
+ * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
+ *
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * E1000_SUCCESS at any other case.
+ */
+static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active)
+{
+ s32 ret_val;
+ u16 phy_data;
+ DEBUGFUNC("e1000_set_d3_lplu_state");
+
+ if (hw->phy_type != e1000_phy_igp)
+ return E1000_SUCCESS;
+
+ /* During driver activity LPLU should not be used or it will attain link
+ * from the lowest speeds starting from 10Mbps. The capability is used for
+ * Dx transitions and states */
+ if (hw->mac_type == e1000_82541_rev_2
+ || hw->mac_type == e1000_82547_rev_2) {
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ if (!active) {
+ if (hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
+ * Dx states where the power conservation is most important. During
+ * driver activity we should enable SmartSpeed, so performance is
+ * maintained. */
+ if (hw->smart_speed == e1000_smart_speed_on) {
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->smart_speed == e1000_smart_speed_off) {
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT)
+ || (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL)
+ || (hw->autoneg_advertised ==
+ AUTONEG_ADVERTISE_10_100_ALL)) {
+
+ if (hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data |= IGP01E1000_GMII_FLEX_SPD;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* When LPLU is enabled we should disable SmartSpeed */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_set_vco_speed
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Change VCO speed register to improve Bit Error Rate performance of SERDES.
+ */
+static s32 e1000_set_vco_speed(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 default_page = 0;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_set_vco_speed");
+
+ switch (hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
+ return E1000_SUCCESS;
+ }
+
+ /* Set PHY register 30, page 5, bit 8 to 0 */
+
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~M88E1000_PHY_VCO_REG_BIT8;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Set PHY register 30, page 4, bit 11 to 1 */
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PHY_VCO_REG_BIT11;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, default_page);
+ if (ret_val)
+ return ret_val;
+
+ return E1000_SUCCESS;
+}
+
+
+/**
+ * e1000_enable_mng_pass_thru - check for bmc pass through
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Verifies the hardware needs to allow ARPs to be processed by the host
+ * returns: - true/false
+ */
+u32 e1000_enable_mng_pass_thru(struct e1000_hw *hw)
+{
+ u32 manc;
+
+ if (hw->asf_firmware_present) {
+ manc = er32(MANC);
+
+ if (!(manc & E1000_MANC_RCV_TCO_EN) ||
+ !(manc & E1000_MANC_EN_MAC_ADDR_FILTER))
+ return false;
+ if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN))
+ return true;
+ }
+ return false;
+}
+
+static s32 e1000_polarity_reversal_workaround(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 mii_status_reg;
+ u16 i;
+
+ /* Polarity reversal workaround for forced 10F/10H links. */
+
+ /* Disable the transmitter on the PHY */
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
+ if (ret_val)
+ return ret_val;
+
+ /* This loop will early-out if the NO link condition has been met. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Link Status bit
+ * to be clear.
+ */
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if ((mii_status_reg & ~MII_SR_LINK_STATUS) == 0)
+ break;
+ mdelay(100);
+ }
+
+ /* Recommended delay time after link has been lost */
+ mdelay(1000);
+
+ /* Now we will re-enable th transmitter on the PHY */
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
+ if (ret_val)
+ return ret_val;
+ mdelay(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0);
+ if (ret_val)
+ return ret_val;
+ mdelay(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00);
+ if (ret_val)
+ return ret_val;
+ mdelay(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
+ if (ret_val)
+ return ret_val;
+
+ /* This loop will early-out if the link condition has been met. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Link Status bit
+ * to be set.
+ */
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (mii_status_reg & MII_SR_LINK_STATUS)
+ break;
+ mdelay(100);
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_get_auto_rd_done
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Check for EEPROM Auto Read bit done.
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ */
+static s32 e1000_get_auto_rd_done(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_get_auto_rd_done");
+ msleep(5);
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_get_phy_cfg_done
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Checks if the PHY configuration is done
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ */
+static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_get_phy_cfg_done");
+ mdelay(10);
+ return E1000_SUCCESS;
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_hw-2.6.32-ethercat.h Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,3048 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/* e1000_hw.h
+ * Structures, enums, and macros for the MAC
+ */
+
+#ifndef _E1000_HW_H_
+#define _E1000_HW_H_
+
+#include "e1000_osdep-2.6.32-ethercat.h"
+
+/* Forward declarations of structures used by the shared code */
+struct e1000_hw;
+struct e1000_hw_stats;
+
+/* Enumerated types specific to the e1000 hardware */
+/* Media Access Controlers */
+typedef enum {
+ e1000_undefined = 0,
+ e1000_82542_rev2_0,
+ e1000_82542_rev2_1,
+ e1000_82543,
+ e1000_82544,
+ e1000_82540,
+ e1000_82545,
+ e1000_82545_rev_3,
+ e1000_82546,
+ e1000_82546_rev_3,
+ e1000_82541,
+ e1000_82541_rev_2,
+ e1000_82547,
+ e1000_82547_rev_2,
+ e1000_num_macs
+} e1000_mac_type;
+
+typedef enum {
+ e1000_eeprom_uninitialized = 0,
+ e1000_eeprom_spi,
+ e1000_eeprom_microwire,
+ e1000_eeprom_flash,
+ e1000_eeprom_none, /* No NVM support */
+ e1000_num_eeprom_types
+} e1000_eeprom_type;
+
+/* Media Types */
+typedef enum {
+ e1000_media_type_copper = 0,
+ e1000_media_type_fiber = 1,
+ e1000_media_type_internal_serdes = 2,
+ e1000_num_media_types
+} e1000_media_type;
+
+typedef enum {
+ e1000_10_half = 0,
+ e1000_10_full = 1,
+ e1000_100_half = 2,
+ e1000_100_full = 3
+} e1000_speed_duplex_type;
+
+/* Flow Control Settings */
+typedef enum {
+ E1000_FC_NONE = 0,
+ E1000_FC_RX_PAUSE = 1,
+ E1000_FC_TX_PAUSE = 2,
+ E1000_FC_FULL = 3,
+ E1000_FC_DEFAULT = 0xFF
+} e1000_fc_type;
+
+struct e1000_shadow_ram {
+ u16 eeprom_word;
+ bool modified;
+};
+
+/* PCI bus types */
+typedef enum {
+ e1000_bus_type_unknown = 0,
+ e1000_bus_type_pci,
+ e1000_bus_type_pcix,
+ e1000_bus_type_reserved
+} e1000_bus_type;
+
+/* PCI bus speeds */
+typedef enum {
+ e1000_bus_speed_unknown = 0,
+ e1000_bus_speed_33,
+ e1000_bus_speed_66,
+ e1000_bus_speed_100,
+ e1000_bus_speed_120,
+ e1000_bus_speed_133,
+ e1000_bus_speed_reserved
+} e1000_bus_speed;
+
+/* PCI bus widths */
+typedef enum {
+ e1000_bus_width_unknown = 0,
+ e1000_bus_width_32,
+ e1000_bus_width_64,
+ e1000_bus_width_reserved
+} e1000_bus_width;
+
+/* PHY status info structure and supporting enums */
+typedef enum {
+ e1000_cable_length_50 = 0,
+ e1000_cable_length_50_80,
+ e1000_cable_length_80_110,
+ e1000_cable_length_110_140,
+ e1000_cable_length_140,
+ e1000_cable_length_undefined = 0xFF
+} e1000_cable_length;
+
+typedef enum {
+ e1000_gg_cable_length_60 = 0,
+ e1000_gg_cable_length_60_115 = 1,
+ e1000_gg_cable_length_115_150 = 2,
+ e1000_gg_cable_length_150 = 4
+} e1000_gg_cable_length;
+
+typedef enum {
+ e1000_igp_cable_length_10 = 10,
+ e1000_igp_cable_length_20 = 20,
+ e1000_igp_cable_length_30 = 30,
+ e1000_igp_cable_length_40 = 40,
+ e1000_igp_cable_length_50 = 50,
+ e1000_igp_cable_length_60 = 60,
+ e1000_igp_cable_length_70 = 70,
+ e1000_igp_cable_length_80 = 80,
+ e1000_igp_cable_length_90 = 90,
+ e1000_igp_cable_length_100 = 100,
+ e1000_igp_cable_length_110 = 110,
+ e1000_igp_cable_length_115 = 115,
+ e1000_igp_cable_length_120 = 120,
+ e1000_igp_cable_length_130 = 130,
+ e1000_igp_cable_length_140 = 140,
+ e1000_igp_cable_length_150 = 150,
+ e1000_igp_cable_length_160 = 160,
+ e1000_igp_cable_length_170 = 170,
+ e1000_igp_cable_length_180 = 180
+} e1000_igp_cable_length;
+
+typedef enum {
+ e1000_10bt_ext_dist_enable_normal = 0,
+ e1000_10bt_ext_dist_enable_lower,
+ e1000_10bt_ext_dist_enable_undefined = 0xFF
+} e1000_10bt_ext_dist_enable;
+
+typedef enum {
+ e1000_rev_polarity_normal = 0,
+ e1000_rev_polarity_reversed,
+ e1000_rev_polarity_undefined = 0xFF
+} e1000_rev_polarity;
+
+typedef enum {
+ e1000_downshift_normal = 0,
+ e1000_downshift_activated,
+ e1000_downshift_undefined = 0xFF
+} e1000_downshift;
+
+typedef enum {
+ e1000_smart_speed_default = 0,
+ e1000_smart_speed_on,
+ e1000_smart_speed_off
+} e1000_smart_speed;
+
+typedef enum {
+ e1000_polarity_reversal_enabled = 0,
+ e1000_polarity_reversal_disabled,
+ e1000_polarity_reversal_undefined = 0xFF
+} e1000_polarity_reversal;
+
+typedef enum {
+ e1000_auto_x_mode_manual_mdi = 0,
+ e1000_auto_x_mode_manual_mdix,
+ e1000_auto_x_mode_auto1,
+ e1000_auto_x_mode_auto2,
+ e1000_auto_x_mode_undefined = 0xFF
+} e1000_auto_x_mode;
+
+typedef enum {
+ e1000_1000t_rx_status_not_ok = 0,
+ e1000_1000t_rx_status_ok,
+ e1000_1000t_rx_status_undefined = 0xFF
+} e1000_1000t_rx_status;
+
+typedef enum {
+ e1000_phy_m88 = 0,
+ e1000_phy_igp,
+ e1000_phy_undefined = 0xFF
+} e1000_phy_type;
+
+typedef enum {
+ e1000_ms_hw_default = 0,
+ e1000_ms_force_master,
+ e1000_ms_force_slave,
+ e1000_ms_auto
+} e1000_ms_type;
+
+typedef enum {
+ e1000_ffe_config_enabled = 0,
+ e1000_ffe_config_active,
+ e1000_ffe_config_blocked
+} e1000_ffe_config;
+
+typedef enum {
+ e1000_dsp_config_disabled = 0,
+ e1000_dsp_config_enabled,
+ e1000_dsp_config_activated,
+ e1000_dsp_config_undefined = 0xFF
+} e1000_dsp_config;
+
+struct e1000_phy_info {
+ e1000_cable_length cable_length;
+ e1000_10bt_ext_dist_enable extended_10bt_distance;
+ e1000_rev_polarity cable_polarity;
+ e1000_downshift downshift;
+ e1000_polarity_reversal polarity_correction;
+ e1000_auto_x_mode mdix_mode;
+ e1000_1000t_rx_status local_rx;
+ e1000_1000t_rx_status remote_rx;
+};
+
+struct e1000_phy_stats {
+ u32 idle_errors;
+ u32 receive_errors;
+};
+
+struct e1000_eeprom_info {
+ e1000_eeprom_type type;
+ u16 word_size;
+ u16 opcode_bits;
+ u16 address_bits;
+ u16 delay_usec;
+ u16 page_size;
+};
+
+/* Flex ASF Information */
+#define E1000_HOST_IF_MAX_SIZE 2048
+
+typedef enum {
+ e1000_byte_align = 0,
+ e1000_word_align = 1,
+ e1000_dword_align = 2
+} e1000_align_type;
+
+/* Error Codes */
+#define E1000_SUCCESS 0
+#define E1000_ERR_EEPROM 1
+#define E1000_ERR_PHY 2
+#define E1000_ERR_CONFIG 3
+#define E1000_ERR_PARAM 4
+#define E1000_ERR_MAC_TYPE 5
+#define E1000_ERR_PHY_TYPE 6
+#define E1000_ERR_RESET 9
+#define E1000_ERR_MASTER_REQUESTS_PENDING 10
+#define E1000_ERR_HOST_INTERFACE_COMMAND 11
+#define E1000_BLK_PHY_RESET 12
+
+#define E1000_BYTE_SWAP_WORD(_value) ((((_value) & 0x00ff) << 8) | \
+ (((_value) & 0xff00) >> 8))
+
+/* Function prototypes */
+/* Initialization */
+s32 e1000_reset_hw(struct e1000_hw *hw);
+s32 e1000_init_hw(struct e1000_hw *hw);
+s32 e1000_set_mac_type(struct e1000_hw *hw);
+void e1000_set_media_type(struct e1000_hw *hw);
+
+/* Link Configuration */
+s32 e1000_setup_link(struct e1000_hw *hw);
+s32 e1000_phy_setup_autoneg(struct e1000_hw *hw);
+void e1000_config_collision_dist(struct e1000_hw *hw);
+s32 e1000_check_for_link(struct e1000_hw *hw);
+s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 * speed, u16 * duplex);
+s32 e1000_force_mac_fc(struct e1000_hw *hw);
+
+/* PHY */
+s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 * phy_data);
+s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 data);
+s32 e1000_phy_hw_reset(struct e1000_hw *hw);
+s32 e1000_phy_reset(struct e1000_hw *hw);
+s32 e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info);
+s32 e1000_validate_mdi_setting(struct e1000_hw *hw);
+
+/* EEPROM Functions */
+s32 e1000_init_eeprom_params(struct e1000_hw *hw);
+
+/* MNG HOST IF functions */
+u32 e1000_enable_mng_pass_thru(struct e1000_hw *hw);
+
+#define E1000_MNG_DHCP_TX_PAYLOAD_CMD 64
+#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8 /* Host Interface data length */
+
+#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10 /* Time in ms to process MNG command */
+#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */
+#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */
+#define E1000_MNG_IAMT_MODE 0x3
+#define E1000_MNG_ICH_IAMT_MODE 0x2
+#define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */
+
+#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */
+#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT 0x2 /* DHCP parsing enabled */
+#define E1000_VFTA_ENTRY_SHIFT 0x5
+#define E1000_VFTA_ENTRY_MASK 0x7F
+#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F
+
+struct e1000_host_mng_command_header {
+ u8 command_id;
+ u8 checksum;
+ u16 reserved1;
+ u16 reserved2;
+ u16 command_length;
+};
+
+struct e1000_host_mng_command_info {
+ struct e1000_host_mng_command_header command_header; /* Command Head/Command Result Head has 4 bytes */
+ u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH]; /* Command data can length 0..0x658 */
+};
+#ifdef __BIG_ENDIAN
+struct e1000_host_mng_dhcp_cookie {
+ u32 signature;
+ u16 vlan_id;
+ u8 reserved0;
+ u8 status;
+ u32 reserved1;
+ u8 checksum;
+ u8 reserved3;
+ u16 reserved2;
+};
+#else
+struct e1000_host_mng_dhcp_cookie {
+ u32 signature;
+ u8 status;
+ u8 reserved0;
+ u16 vlan_id;
+ u32 reserved1;
+ u16 reserved2;
+ u8 reserved3;
+ u8 checksum;
+};
+#endif
+
+bool e1000_check_mng_mode(struct e1000_hw *hw);
+s32 e1000_read_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 * data);
+s32 e1000_validate_eeprom_checksum(struct e1000_hw *hw);
+s32 e1000_update_eeprom_checksum(struct e1000_hw *hw);
+s32 e1000_write_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 * data);
+s32 e1000_read_mac_addr(struct e1000_hw *hw);
+
+/* Filters (multicast, vlan, receive) */
+u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 * mc_addr);
+void e1000_mta_set(struct e1000_hw *hw, u32 hash_value);
+void e1000_rar_set(struct e1000_hw *hw, u8 * mc_addr, u32 rar_index);
+void e1000_write_vfta(struct e1000_hw *hw, u32 offset, u32 value);
+
+/* LED functions */
+s32 e1000_setup_led(struct e1000_hw *hw);
+s32 e1000_cleanup_led(struct e1000_hw *hw);
+s32 e1000_led_on(struct e1000_hw *hw);
+s32 e1000_led_off(struct e1000_hw *hw);
+s32 e1000_blink_led_start(struct e1000_hw *hw);
+
+/* Adaptive IFS Functions */
+
+/* Everything else */
+void e1000_reset_adaptive(struct e1000_hw *hw);
+void e1000_update_adaptive(struct e1000_hw *hw);
+void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats,
+ u32 frame_len, u8 * mac_addr);
+void e1000_get_bus_info(struct e1000_hw *hw);
+void e1000_pci_set_mwi(struct e1000_hw *hw);
+void e1000_pci_clear_mwi(struct e1000_hw *hw);
+void e1000_pcix_set_mmrbc(struct e1000_hw *hw, int mmrbc);
+int e1000_pcix_get_mmrbc(struct e1000_hw *hw);
+/* Port I/O is only supported on 82544 and newer */
+void e1000_io_write(struct e1000_hw *hw, unsigned long port, u32 value);
+
+#define E1000_READ_REG_IO(a, reg) \
+ e1000_read_reg_io((a), E1000_##reg)
+#define E1000_WRITE_REG_IO(a, reg, val) \
+ e1000_write_reg_io((a), E1000_##reg, val)
+
+/* PCI Device IDs */
+#define E1000_DEV_ID_82542 0x1000
+#define E1000_DEV_ID_82543GC_FIBER 0x1001
+#define E1000_DEV_ID_82543GC_COPPER 0x1004
+#define E1000_DEV_ID_82544EI_COPPER 0x1008
+#define E1000_DEV_ID_82544EI_FIBER 0x1009
+#define E1000_DEV_ID_82544GC_COPPER 0x100C
+#define E1000_DEV_ID_82544GC_LOM 0x100D
+#define E1000_DEV_ID_82540EM 0x100E
+#define E1000_DEV_ID_82540EM_LOM 0x1015
+#define E1000_DEV_ID_82540EP_LOM 0x1016
+#define E1000_DEV_ID_82540EP 0x1017
+#define E1000_DEV_ID_82540EP_LP 0x101E
+#define E1000_DEV_ID_82545EM_COPPER 0x100F
+#define E1000_DEV_ID_82545EM_FIBER 0x1011
+#define E1000_DEV_ID_82545GM_COPPER 0x1026
+#define E1000_DEV_ID_82545GM_FIBER 0x1027
+#define E1000_DEV_ID_82545GM_SERDES 0x1028
+#define E1000_DEV_ID_82546EB_COPPER 0x1010
+#define E1000_DEV_ID_82546EB_FIBER 0x1012
+#define E1000_DEV_ID_82546EB_QUAD_COPPER 0x101D
+#define E1000_DEV_ID_82541EI 0x1013
+#define E1000_DEV_ID_82541EI_MOBILE 0x1018
+#define E1000_DEV_ID_82541ER_LOM 0x1014
+#define E1000_DEV_ID_82541ER 0x1078
+#define E1000_DEV_ID_82547GI 0x1075
+#define E1000_DEV_ID_82541GI 0x1076
+#define E1000_DEV_ID_82541GI_MOBILE 0x1077
+#define E1000_DEV_ID_82541GI_LF 0x107C
+#define E1000_DEV_ID_82546GB_COPPER 0x1079
+#define E1000_DEV_ID_82546GB_FIBER 0x107A
+#define E1000_DEV_ID_82546GB_SERDES 0x107B
+#define E1000_DEV_ID_82546GB_PCIE 0x108A
+#define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099
+#define E1000_DEV_ID_82547EI 0x1019
+#define E1000_DEV_ID_82547EI_MOBILE 0x101A
+#define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5
+
+#define NODE_ADDRESS_SIZE 6
+#define ETH_LENGTH_OF_ADDRESS 6
+
+/* MAC decode size is 128K - This is the size of BAR0 */
+#define MAC_DECODE_SIZE (128 * 1024)
+
+#define E1000_82542_2_0_REV_ID 2
+#define E1000_82542_2_1_REV_ID 3
+#define E1000_REVISION_0 0
+#define E1000_REVISION_1 1
+#define E1000_REVISION_2 2
+#define E1000_REVISION_3 3
+
+#define SPEED_10 10
+#define SPEED_100 100
+#define SPEED_1000 1000
+#define HALF_DUPLEX 1
+#define FULL_DUPLEX 2
+
+/* The sizes (in bytes) of a ethernet packet */
+#define ENET_HEADER_SIZE 14
+#define MINIMUM_ETHERNET_FRAME_SIZE 64 /* With FCS */
+#define ETHERNET_FCS_SIZE 4
+#define MINIMUM_ETHERNET_PACKET_SIZE \
+ (MINIMUM_ETHERNET_FRAME_SIZE - ETHERNET_FCS_SIZE)
+#define CRC_LENGTH ETHERNET_FCS_SIZE
+#define MAX_JUMBO_FRAME_SIZE 0x3F00
+
+/* 802.1q VLAN Packet Sizes */
+#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMAed) */
+
+/* Ethertype field values */
+#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */
+#define ETHERNET_IP_TYPE 0x0800 /* IP packets */
+#define ETHERNET_ARP_TYPE 0x0806 /* Address Resolution Protocol (ARP) */
+
+/* Packet Header defines */
+#define IP_PROTOCOL_TCP 6
+#define IP_PROTOCOL_UDP 0x11
+
+/* This defines the bits that are set in the Interrupt Mask
+ * Set/Read Register. Each bit is documented below:
+ * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
+ * o RXSEQ = Receive Sequence Error
+ */
+#define POLL_IMS_ENABLE_MASK ( \
+ E1000_IMS_RXDMT0 | \
+ E1000_IMS_RXSEQ)
+
+/* This defines the bits that are set in the Interrupt Mask
+ * Set/Read Register. Each bit is documented below:
+ * o RXT0 = Receiver Timer Interrupt (ring 0)
+ * o TXDW = Transmit Descriptor Written Back
+ * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
+ * o RXSEQ = Receive Sequence Error
+ * o LSC = Link Status Change
+ */
+#define IMS_ENABLE_MASK ( \
+ E1000_IMS_RXT0 | \
+ E1000_IMS_TXDW | \
+ E1000_IMS_RXDMT0 | \
+ E1000_IMS_RXSEQ | \
+ E1000_IMS_LSC)
+
+/* Number of high/low register pairs in the RAR. The RAR (Receive Address
+ * Registers) holds the directed and multicast addresses that we monitor. We
+ * reserve one of these spots for our directed address, allowing us room for
+ * E1000_RAR_ENTRIES - 1 multicast addresses.
+ */
+#define E1000_RAR_ENTRIES 15
+
+#define MIN_NUMBER_OF_DESCRIPTORS 8
+#define MAX_NUMBER_OF_DESCRIPTORS 0xFFF8
+
+/* Receive Descriptor */
+struct e1000_rx_desc {
+ __le64 buffer_addr; /* Address of the descriptor's data buffer */
+ __le16 length; /* Length of data DMAed into data buffer */
+ __le16 csum; /* Packet checksum */
+ u8 status; /* Descriptor status */
+ u8 errors; /* Descriptor Errors */
+ __le16 special;
+};
+
+/* Receive Descriptor - Extended */
+union e1000_rx_desc_extended {
+ struct {
+ __le64 buffer_addr;
+ __le64 reserved;
+ } read;
+ struct {
+ struct {
+ __le32 mrq; /* Multiple Rx Queues */
+ union {
+ __le32 rss; /* RSS Hash */
+ struct {
+ __le16 ip_id; /* IP id */
+ __le16 csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ __le32 status_error; /* ext status/error */
+ __le16 length;
+ __le16 vlan; /* VLAN tag */
+ } upper;
+ } wb; /* writeback */
+};
+
+#define MAX_PS_BUFFERS 4
+/* Receive Descriptor - Packet Split */
+union e1000_rx_desc_packet_split {
+ struct {
+ /* one buffer for protocol header(s), three data buffers */
+ __le64 buffer_addr[MAX_PS_BUFFERS];
+ } read;
+ struct {
+ struct {
+ __le32 mrq; /* Multiple Rx Queues */
+ union {
+ __le32 rss; /* RSS Hash */
+ struct {
+ __le16 ip_id; /* IP id */
+ __le16 csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ __le32 status_error; /* ext status/error */
+ __le16 length0; /* length of buffer 0 */
+ __le16 vlan; /* VLAN tag */
+ } middle;
+ struct {
+ __le16 header_status;
+ __le16 length[3]; /* length of buffers 1-3 */
+ } upper;
+ __le64 reserved;
+ } wb; /* writeback */
+};
+
+/* Receive Descriptor bit definitions */
+#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
+#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
+#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
+#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
+#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
+#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
+#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */
+#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */
+#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */
+#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */
+#define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */
+#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
+#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
+#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
+#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
+#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */
+#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */
+#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
+#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
+#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */
+#define E1000_RXD_SPC_PRI_SHIFT 13
+#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */
+#define E1000_RXD_SPC_CFI_SHIFT 12
+
+#define E1000_RXDEXT_STATERR_CE 0x01000000
+#define E1000_RXDEXT_STATERR_SE 0x02000000
+#define E1000_RXDEXT_STATERR_SEQ 0x04000000
+#define E1000_RXDEXT_STATERR_CXE 0x10000000
+#define E1000_RXDEXT_STATERR_TCPE 0x20000000
+#define E1000_RXDEXT_STATERR_IPE 0x40000000
+#define E1000_RXDEXT_STATERR_RXE 0x80000000
+
+#define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000
+#define E1000_RXDPS_HDRSTAT_HDRLEN_MASK 0x000003FF
+
+/* mask to determine if packets should be dropped due to frame errors */
+#define E1000_RXD_ERR_FRAME_ERR_MASK ( \
+ E1000_RXD_ERR_CE | \
+ E1000_RXD_ERR_SE | \
+ E1000_RXD_ERR_SEQ | \
+ E1000_RXD_ERR_CXE | \
+ E1000_RXD_ERR_RXE)
+
+/* Same mask, but for extended and packet split descriptors */
+#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
+ E1000_RXDEXT_STATERR_CE | \
+ E1000_RXDEXT_STATERR_SE | \
+ E1000_RXDEXT_STATERR_SEQ | \
+ E1000_RXDEXT_STATERR_CXE | \
+ E1000_RXDEXT_STATERR_RXE)
+
+/* Transmit Descriptor */
+struct e1000_tx_desc {
+ __le64 buffer_addr; /* Address of the descriptor's data buffer */
+ union {
+ __le32 data;
+ struct {
+ __le16 length; /* Data buffer length */
+ u8 cso; /* Checksum offset */
+ u8 cmd; /* Descriptor control */
+ } flags;
+ } lower;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 css; /* Checksum start */
+ __le16 special;
+ } fields;
+ } upper;
+};
+
+/* Transmit Descriptor bit definitions */
+#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */
+#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */
+#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
+#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
+#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
+#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
+#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
+#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
+#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
+#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
+#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
+#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
+#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
+#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
+#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
+#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
+#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
+#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
+#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
+#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
+
+/* Offload Context Descriptor */
+struct e1000_context_desc {
+ union {
+ __le32 ip_config;
+ struct {
+ u8 ipcss; /* IP checksum start */
+ u8 ipcso; /* IP checksum offset */
+ __le16 ipcse; /* IP checksum end */
+ } ip_fields;
+ } lower_setup;
+ union {
+ __le32 tcp_config;
+ struct {
+ u8 tucss; /* TCP checksum start */
+ u8 tucso; /* TCP checksum offset */
+ __le16 tucse; /* TCP checksum end */
+ } tcp_fields;
+ } upper_setup;
+ __le32 cmd_and_length; /* */
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 hdr_len; /* Header length */
+ __le16 mss; /* Maximum segment size */
+ } fields;
+ } tcp_seg_setup;
+};
+
+/* Offload data descriptor */
+struct e1000_data_desc {
+ __le64 buffer_addr; /* Address of the descriptor's buffer address */
+ union {
+ __le32 data;
+ struct {
+ __le16 length; /* Data buffer length */
+ u8 typ_len_ext; /* */
+ u8 cmd; /* */
+ } flags;
+ } lower;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 popts; /* Packet Options */
+ __le16 special; /* */
+ } fields;
+ } upper;
+};
+
+/* Filters */
+#define E1000_NUM_UNICAST 16 /* Unicast filter entries */
+#define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */
+#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
+
+/* Receive Address Register */
+struct e1000_rar {
+ volatile __le32 low; /* receive address low */
+ volatile __le32 high; /* receive address high */
+};
+
+/* Number of entries in the Multicast Table Array (MTA). */
+#define E1000_NUM_MTA_REGISTERS 128
+
+/* IPv4 Address Table Entry */
+struct e1000_ipv4_at_entry {
+ volatile u32 ipv4_addr; /* IP Address (RW) */
+ volatile u32 reserved;
+};
+
+/* Four wakeup IP addresses are supported */
+#define E1000_WAKEUP_IP_ADDRESS_COUNT_MAX 4
+#define E1000_IP4AT_SIZE E1000_WAKEUP_IP_ADDRESS_COUNT_MAX
+#define E1000_IP6AT_SIZE 1
+
+/* IPv6 Address Table Entry */
+struct e1000_ipv6_at_entry {
+ volatile u8 ipv6_addr[16];
+};
+
+/* Flexible Filter Length Table Entry */
+struct e1000_fflt_entry {
+ volatile u32 length; /* Flexible Filter Length (RW) */
+ volatile u32 reserved;
+};
+
+/* Flexible Filter Mask Table Entry */
+struct e1000_ffmt_entry {
+ volatile u32 mask; /* Flexible Filter Mask (RW) */
+ volatile u32 reserved;
+};
+
+/* Flexible Filter Value Table Entry */
+struct e1000_ffvt_entry {
+ volatile u32 value; /* Flexible Filter Value (RW) */
+ volatile u32 reserved;
+};
+
+/* Four Flexible Filters are supported */
+#define E1000_FLEXIBLE_FILTER_COUNT_MAX 4
+
+/* Each Flexible Filter is at most 128 (0x80) bytes in length */
+#define E1000_FLEXIBLE_FILTER_SIZE_MAX 128
+
+#define E1000_FFLT_SIZE E1000_FLEXIBLE_FILTER_COUNT_MAX
+#define E1000_FFMT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX
+#define E1000_FFVT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX
+
+#define E1000_DISABLE_SERDES_LOOPBACK 0x0400
+
+/* Register Set. (82543, 82544)
+ *
+ * Registers are defined to be 32 bits and should be accessed as 32 bit values.
+ * These registers are physically located on the NIC, but are mapped into the
+ * host memory address space.
+ *
+ * RW - register is both readable and writable
+ * RO - register is read only
+ * WO - register is write only
+ * R/clr - register is read only and is cleared when read
+ * A - register array
+ */
+#define E1000_CTRL 0x00000 /* Device Control - RW */
+#define E1000_CTRL_DUP 0x00004 /* Device Control Duplicate (Shadow) - RW */
+#define E1000_STATUS 0x00008 /* Device Status - RO */
+#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */
+#define E1000_EERD 0x00014 /* EEPROM Read - RW */
+#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */
+#define E1000_FLA 0x0001C /* Flash Access - RW */
+#define E1000_MDIC 0x00020 /* MDI Control - RW */
+#define E1000_SCTL 0x00024 /* SerDes Control - RW */
+#define E1000_FEXTNVM 0x00028 /* Future Extended NVM register */
+#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */
+#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */
+#define E1000_FCT 0x00030 /* Flow Control Type - RW */
+#define E1000_VET 0x00038 /* VLAN Ether Type - RW */
+#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */
+#define E1000_ITR 0x000C4 /* Interrupt Throttling Rate - RW */
+#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */
+#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */
+#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */
+#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */
+#define E1000_RCTL 0x00100 /* RX Control - RW */
+#define E1000_RDTR1 0x02820 /* RX Delay Timer (1) - RW */
+#define E1000_RDBAL1 0x02900 /* RX Descriptor Base Address Low (1) - RW */
+#define E1000_RDBAH1 0x02904 /* RX Descriptor Base Address High (1) - RW */
+#define E1000_RDLEN1 0x02908 /* RX Descriptor Length (1) - RW */
+#define E1000_RDH1 0x02910 /* RX Descriptor Head (1) - RW */
+#define E1000_RDT1 0x02918 /* RX Descriptor Tail (1) - RW */
+#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */
+#define E1000_TXCW 0x00178 /* TX Configuration Word - RW */
+#define E1000_RXCW 0x00180 /* RX Configuration Word - RO */
+#define E1000_TCTL 0x00400 /* TX Control - RW */
+#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */
+#define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */
+#define E1000_TBT 0x00448 /* TX Burst Timer - RW */
+#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */
+#define E1000_LEDCTL 0x00E00 /* LED Control - RW */
+#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */
+#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */
+#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */
+#define FEXTNVM_SW_CONFIG 0x0001
+#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
+#define E1000_PBS 0x01008 /* Packet Buffer Size */
+#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
+#define E1000_FLASH_UPDATES 1000
+#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */
+#define E1000_FLASHT 0x01028 /* FLASH Timer Register */
+#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */
+#define E1000_FLSWCTL 0x01030 /* FLASH control register */
+#define E1000_FLSWDATA 0x01034 /* FLASH data register */
+#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */
+#define E1000_FLOP 0x0103C /* FLASH Opcode Register */
+#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */
+#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */
+#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */
+#define E1000_PSRCTL 0x02170 /* Packet Split Receive Control - RW */
+#define E1000_RDBAL 0x02800 /* RX Descriptor Base Address Low - RW */
+#define E1000_RDBAH 0x02804 /* RX Descriptor Base Address High - RW */
+#define E1000_RDLEN 0x02808 /* RX Descriptor Length - RW */
+#define E1000_RDH 0x02810 /* RX Descriptor Head - RW */
+#define E1000_RDT 0x02818 /* RX Descriptor Tail - RW */
+#define E1000_RDTR 0x02820 /* RX Delay Timer - RW */
+#define E1000_RDBAL0 E1000_RDBAL /* RX Desc Base Address Low (0) - RW */
+#define E1000_RDBAH0 E1000_RDBAH /* RX Desc Base Address High (0) - RW */
+#define E1000_RDLEN0 E1000_RDLEN /* RX Desc Length (0) - RW */
+#define E1000_RDH0 E1000_RDH /* RX Desc Head (0) - RW */
+#define E1000_RDT0 E1000_RDT /* RX Desc Tail (0) - RW */
+#define E1000_RDTR0 E1000_RDTR /* RX Delay Timer (0) - RW */
+#define E1000_RXDCTL 0x02828 /* RX Descriptor Control queue 0 - RW */
+#define E1000_RXDCTL1 0x02928 /* RX Descriptor Control queue 1 - RW */
+#define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */
+#define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */
+#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */
+#define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */
+#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */
+#define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */
+#define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */
+#define E1000_TDFHS 0x03420 /* TX Data FIFO Head Saved - RW */
+#define E1000_TDFTS 0x03428 /* TX Data FIFO Tail Saved - RW */
+#define E1000_TDFPC 0x03430 /* TX Data FIFO Packet Count - RW */
+#define E1000_TDBAL 0x03800 /* TX Descriptor Base Address Low - RW */
+#define E1000_TDBAH 0x03804 /* TX Descriptor Base Address High - RW */
+#define E1000_TDLEN 0x03808 /* TX Descriptor Length - RW */
+#define E1000_TDH 0x03810 /* TX Descriptor Head - RW */
+#define E1000_TDT 0x03818 /* TX Descripotr Tail - RW */
+#define E1000_TIDV 0x03820 /* TX Interrupt Delay Value - RW */
+#define E1000_TXDCTL 0x03828 /* TX Descriptor Control - RW */
+#define E1000_TADV 0x0382C /* TX Interrupt Absolute Delay Val - RW */
+#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */
+#define E1000_TARC0 0x03840 /* TX Arbitration Count (0) */
+#define E1000_TDBAL1 0x03900 /* TX Desc Base Address Low (1) - RW */
+#define E1000_TDBAH1 0x03904 /* TX Desc Base Address High (1) - RW */
+#define E1000_TDLEN1 0x03908 /* TX Desc Length (1) - RW */
+#define E1000_TDH1 0x03910 /* TX Desc Head (1) - RW */
+#define E1000_TDT1 0x03918 /* TX Desc Tail (1) - RW */
+#define E1000_TXDCTL1 0x03928 /* TX Descriptor Control (1) - RW */
+#define E1000_TARC1 0x03940 /* TX Arbitration Count (1) */
+#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */
+#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */
+#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */
+#define E1000_RXERRC 0x0400C /* Receive Error Count - R/clr */
+#define E1000_MPC 0x04010 /* Missed Packet Count - R/clr */
+#define E1000_SCC 0x04014 /* Single Collision Count - R/clr */
+#define E1000_ECOL 0x04018 /* Excessive Collision Count - R/clr */
+#define E1000_MCC 0x0401C /* Multiple Collision Count - R/clr */
+#define E1000_LATECOL 0x04020 /* Late Collision Count - R/clr */
+#define E1000_COLC 0x04028 /* Collision Count - R/clr */
+#define E1000_DC 0x04030 /* Defer Count - R/clr */
+#define E1000_TNCRS 0x04034 /* TX-No CRS - R/clr */
+#define E1000_SEC 0x04038 /* Sequence Error Count - R/clr */
+#define E1000_CEXTERR 0x0403C /* Carrier Extension Error Count - R/clr */
+#define E1000_RLEC 0x04040 /* Receive Length Error Count - R/clr */
+#define E1000_XONRXC 0x04048 /* XON RX Count - R/clr */
+#define E1000_XONTXC 0x0404C /* XON TX Count - R/clr */
+#define E1000_XOFFRXC 0x04050 /* XOFF RX Count - R/clr */
+#define E1000_XOFFTXC 0x04054 /* XOFF TX Count - R/clr */
+#define E1000_FCRUC 0x04058 /* Flow Control RX Unsupported Count- R/clr */
+#define E1000_PRC64 0x0405C /* Packets RX (64 bytes) - R/clr */
+#define E1000_PRC127 0x04060 /* Packets RX (65-127 bytes) - R/clr */
+#define E1000_PRC255 0x04064 /* Packets RX (128-255 bytes) - R/clr */
+#define E1000_PRC511 0x04068 /* Packets RX (255-511 bytes) - R/clr */
+#define E1000_PRC1023 0x0406C /* Packets RX (512-1023 bytes) - R/clr */
+#define E1000_PRC1522 0x04070 /* Packets RX (1024-1522 bytes) - R/clr */
+#define E1000_GPRC 0x04074 /* Good Packets RX Count - R/clr */
+#define E1000_BPRC 0x04078 /* Broadcast Packets RX Count - R/clr */
+#define E1000_MPRC 0x0407C /* Multicast Packets RX Count - R/clr */
+#define E1000_GPTC 0x04080 /* Good Packets TX Count - R/clr */
+#define E1000_GORCL 0x04088 /* Good Octets RX Count Low - R/clr */
+#define E1000_GORCH 0x0408C /* Good Octets RX Count High - R/clr */
+#define E1000_GOTCL 0x04090 /* Good Octets TX Count Low - R/clr */
+#define E1000_GOTCH 0x04094 /* Good Octets TX Count High - R/clr */
+#define E1000_RNBC 0x040A0 /* RX No Buffers Count - R/clr */
+#define E1000_RUC 0x040A4 /* RX Undersize Count - R/clr */
+#define E1000_RFC 0x040A8 /* RX Fragment Count - R/clr */
+#define E1000_ROC 0x040AC /* RX Oversize Count - R/clr */
+#define E1000_RJC 0x040B0 /* RX Jabber Count - R/clr */
+#define E1000_MGTPRC 0x040B4 /* Management Packets RX Count - R/clr */
+#define E1000_MGTPDC 0x040B8 /* Management Packets Dropped Count - R/clr */
+#define E1000_MGTPTC 0x040BC /* Management Packets TX Count - R/clr */
+#define E1000_TORL 0x040C0 /* Total Octets RX Low - R/clr */
+#define E1000_TORH 0x040C4 /* Total Octets RX High - R/clr */
+#define E1000_TOTL 0x040C8 /* Total Octets TX Low - R/clr */
+#define E1000_TOTH 0x040CC /* Total Octets TX High - R/clr */
+#define E1000_TPR 0x040D0 /* Total Packets RX - R/clr */
+#define E1000_TPT 0x040D4 /* Total Packets TX - R/clr */
+#define E1000_PTC64 0x040D8 /* Packets TX (64 bytes) - R/clr */
+#define E1000_PTC127 0x040DC /* Packets TX (65-127 bytes) - R/clr */
+#define E1000_PTC255 0x040E0 /* Packets TX (128-255 bytes) - R/clr */
+#define E1000_PTC511 0x040E4 /* Packets TX (256-511 bytes) - R/clr */
+#define E1000_PTC1023 0x040E8 /* Packets TX (512-1023 bytes) - R/clr */
+#define E1000_PTC1522 0x040EC /* Packets TX (1024-1522 Bytes) - R/clr */
+#define E1000_MPTC 0x040F0 /* Multicast Packets TX Count - R/clr */
+#define E1000_BPTC 0x040F4 /* Broadcast Packets TX Count - R/clr */
+#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context TX - R/clr */
+#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context TX Fail - R/clr */
+#define E1000_IAC 0x04100 /* Interrupt Assertion Count */
+#define E1000_ICRXPTC 0x04104 /* Interrupt Cause Rx Packet Timer Expire Count */
+#define E1000_ICRXATC 0x04108 /* Interrupt Cause Rx Absolute Timer Expire Count */
+#define E1000_ICTXPTC 0x0410C /* Interrupt Cause Tx Packet Timer Expire Count */
+#define E1000_ICTXATC 0x04110 /* Interrupt Cause Tx Absolute Timer Expire Count */
+#define E1000_ICTXQEC 0x04118 /* Interrupt Cause Tx Queue Empty Count */
+#define E1000_ICTXQMTC 0x0411C /* Interrupt Cause Tx Queue Minimum Threshold Count */
+#define E1000_ICRXDMTC 0x04120 /* Interrupt Cause Rx Descriptor Minimum Threshold Count */
+#define E1000_ICRXOC 0x04124 /* Interrupt Cause Receiver Overrun Count */
+#define E1000_RXCSUM 0x05000 /* RX Checksum Control - RW */
+#define E1000_RFCTL 0x05008 /* Receive Filter Control */
+#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */
+#define E1000_RA 0x05400 /* Receive Address - RW Array */
+#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */
+#define E1000_WUC 0x05800 /* Wakeup Control - RW */
+#define E1000_WUFC 0x05808 /* Wakeup Filter Control - RW */
+#define E1000_WUS 0x05810 /* Wakeup Status - RO */
+#define E1000_MANC 0x05820 /* Management Control - RW */
+#define E1000_IPAV 0x05838 /* IP Address Valid - RW */
+#define E1000_IP4AT 0x05840 /* IPv4 Address Table - RW Array */
+#define E1000_IP6AT 0x05880 /* IPv6 Address Table - RW Array */
+#define E1000_WUPL 0x05900 /* Wakeup Packet Length - RW */
+#define E1000_WUPM 0x05A00 /* Wakeup Packet Memory - RO A */
+#define E1000_FFLT 0x05F00 /* Flexible Filter Length Table - RW Array */
+#define E1000_HOST_IF 0x08800 /* Host Interface */
+#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */
+#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */
+
+#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */
+#define E1000_MDPHYA 0x0003C /* PHY address - RW */
+#define E1000_MANC2H 0x05860 /* Managment Control To Host - RW */
+#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */
+
+#define E1000_GCR 0x05B00 /* PCI-Ex Control */
+#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */
+#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */
+#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */
+#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */
+#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */
+#define E1000_SWSM 0x05B50 /* SW Semaphore */
+#define E1000_FWSM 0x05B54 /* FW Semaphore */
+#define E1000_FFLT_DBG 0x05F04 /* Debug Register */
+#define E1000_HICR 0x08F00 /* Host Interface Control */
+
+/* RSS registers */
+#define E1000_CPUVEC 0x02C10 /* CPU Vector Register - RW */
+#define E1000_MRQC 0x05818 /* Multiple Receive Control - RW */
+#define E1000_RETA 0x05C00 /* Redirection Table - RW Array */
+#define E1000_RSSRK 0x05C80 /* RSS Random Key - RW Array */
+#define E1000_RSSIM 0x05864 /* RSS Interrupt Mask */
+#define E1000_RSSIR 0x05868 /* RSS Interrupt Request */
+/* Register Set (82542)
+ *
+ * Some of the 82542 registers are located at different offsets than they are
+ * in more current versions of the 8254x. Despite the difference in location,
+ * the registers function in the same manner.
+ */
+#define E1000_82542_CTRL E1000_CTRL
+#define E1000_82542_CTRL_DUP E1000_CTRL_DUP
+#define E1000_82542_STATUS E1000_STATUS
+#define E1000_82542_EECD E1000_EECD
+#define E1000_82542_EERD E1000_EERD
+#define E1000_82542_CTRL_EXT E1000_CTRL_EXT
+#define E1000_82542_FLA E1000_FLA
+#define E1000_82542_MDIC E1000_MDIC
+#define E1000_82542_SCTL E1000_SCTL
+#define E1000_82542_FEXTNVM E1000_FEXTNVM
+#define E1000_82542_FCAL E1000_FCAL
+#define E1000_82542_FCAH E1000_FCAH
+#define E1000_82542_FCT E1000_FCT
+#define E1000_82542_VET E1000_VET
+#define E1000_82542_RA 0x00040
+#define E1000_82542_ICR E1000_ICR
+#define E1000_82542_ITR E1000_ITR
+#define E1000_82542_ICS E1000_ICS
+#define E1000_82542_IMS E1000_IMS
+#define E1000_82542_IMC E1000_IMC
+#define E1000_82542_RCTL E1000_RCTL
+#define E1000_82542_RDTR 0x00108
+#define E1000_82542_RDBAL 0x00110
+#define E1000_82542_RDBAH 0x00114
+#define E1000_82542_RDLEN 0x00118
+#define E1000_82542_RDH 0x00120
+#define E1000_82542_RDT 0x00128
+#define E1000_82542_RDTR0 E1000_82542_RDTR
+#define E1000_82542_RDBAL0 E1000_82542_RDBAL
+#define E1000_82542_RDBAH0 E1000_82542_RDBAH
+#define E1000_82542_RDLEN0 E1000_82542_RDLEN
+#define E1000_82542_RDH0 E1000_82542_RDH
+#define E1000_82542_RDT0 E1000_82542_RDT
+#define E1000_82542_SRRCTL(_n) (0x280C + ((_n) << 8)) /* Split and Replication
+ * RX Control - RW */
+#define E1000_82542_DCA_RXCTRL(_n) (0x02814 + ((_n) << 8))
+#define E1000_82542_RDBAH3 0x02B04 /* RX Desc Base High Queue 3 - RW */
+#define E1000_82542_RDBAL3 0x02B00 /* RX Desc Low Queue 3 - RW */
+#define E1000_82542_RDLEN3 0x02B08 /* RX Desc Length Queue 3 - RW */
+#define E1000_82542_RDH3 0x02B10 /* RX Desc Head Queue 3 - RW */
+#define E1000_82542_RDT3 0x02B18 /* RX Desc Tail Queue 3 - RW */
+#define E1000_82542_RDBAL2 0x02A00 /* RX Desc Base Low Queue 2 - RW */
+#define E1000_82542_RDBAH2 0x02A04 /* RX Desc Base High Queue 2 - RW */
+#define E1000_82542_RDLEN2 0x02A08 /* RX Desc Length Queue 2 - RW */
+#define E1000_82542_RDH2 0x02A10 /* RX Desc Head Queue 2 - RW */
+#define E1000_82542_RDT2 0x02A18 /* RX Desc Tail Queue 2 - RW */
+#define E1000_82542_RDTR1 0x00130
+#define E1000_82542_RDBAL1 0x00138
+#define E1000_82542_RDBAH1 0x0013C
+#define E1000_82542_RDLEN1 0x00140
+#define E1000_82542_RDH1 0x00148
+#define E1000_82542_RDT1 0x00150
+#define E1000_82542_FCRTH 0x00160
+#define E1000_82542_FCRTL 0x00168
+#define E1000_82542_FCTTV E1000_FCTTV
+#define E1000_82542_TXCW E1000_TXCW
+#define E1000_82542_RXCW E1000_RXCW
+#define E1000_82542_MTA 0x00200
+#define E1000_82542_TCTL E1000_TCTL
+#define E1000_82542_TCTL_EXT E1000_TCTL_EXT
+#define E1000_82542_TIPG E1000_TIPG
+#define E1000_82542_TDBAL 0x00420
+#define E1000_82542_TDBAH 0x00424
+#define E1000_82542_TDLEN 0x00428
+#define E1000_82542_TDH 0x00430
+#define E1000_82542_TDT 0x00438
+#define E1000_82542_TIDV 0x00440
+#define E1000_82542_TBT E1000_TBT
+#define E1000_82542_AIT E1000_AIT
+#define E1000_82542_VFTA 0x00600
+#define E1000_82542_LEDCTL E1000_LEDCTL
+#define E1000_82542_PBA E1000_PBA
+#define E1000_82542_PBS E1000_PBS
+#define E1000_82542_EEMNGCTL E1000_EEMNGCTL
+#define E1000_82542_EEARBC E1000_EEARBC
+#define E1000_82542_FLASHT E1000_FLASHT
+#define E1000_82542_EEWR E1000_EEWR
+#define E1000_82542_FLSWCTL E1000_FLSWCTL
+#define E1000_82542_FLSWDATA E1000_FLSWDATA
+#define E1000_82542_FLSWCNT E1000_FLSWCNT
+#define E1000_82542_FLOP E1000_FLOP
+#define E1000_82542_EXTCNF_CTRL E1000_EXTCNF_CTRL
+#define E1000_82542_EXTCNF_SIZE E1000_EXTCNF_SIZE
+#define E1000_82542_PHY_CTRL E1000_PHY_CTRL
+#define E1000_82542_ERT E1000_ERT
+#define E1000_82542_RXDCTL E1000_RXDCTL
+#define E1000_82542_RXDCTL1 E1000_RXDCTL1
+#define E1000_82542_RADV E1000_RADV
+#define E1000_82542_RSRPD E1000_RSRPD
+#define E1000_82542_TXDMAC E1000_TXDMAC
+#define E1000_82542_KABGTXD E1000_KABGTXD
+#define E1000_82542_TDFHS E1000_TDFHS
+#define E1000_82542_TDFTS E1000_TDFTS
+#define E1000_82542_TDFPC E1000_TDFPC
+#define E1000_82542_TXDCTL E1000_TXDCTL
+#define E1000_82542_TADV E1000_TADV
+#define E1000_82542_TSPMT E1000_TSPMT
+#define E1000_82542_CRCERRS E1000_CRCERRS
+#define E1000_82542_ALGNERRC E1000_ALGNERRC
+#define E1000_82542_SYMERRS E1000_SYMERRS
+#define E1000_82542_RXERRC E1000_RXERRC
+#define E1000_82542_MPC E1000_MPC
+#define E1000_82542_SCC E1000_SCC
+#define E1000_82542_ECOL E1000_ECOL
+#define E1000_82542_MCC E1000_MCC
+#define E1000_82542_LATECOL E1000_LATECOL
+#define E1000_82542_COLC E1000_COLC
+#define E1000_82542_DC E1000_DC
+#define E1000_82542_TNCRS E1000_TNCRS
+#define E1000_82542_SEC E1000_SEC
+#define E1000_82542_CEXTERR E1000_CEXTERR
+#define E1000_82542_RLEC E1000_RLEC
+#define E1000_82542_XONRXC E1000_XONRXC
+#define E1000_82542_XONTXC E1000_XONTXC
+#define E1000_82542_XOFFRXC E1000_XOFFRXC
+#define E1000_82542_XOFFTXC E1000_XOFFTXC
+#define E1000_82542_FCRUC E1000_FCRUC
+#define E1000_82542_PRC64 E1000_PRC64
+#define E1000_82542_PRC127 E1000_PRC127
+#define E1000_82542_PRC255 E1000_PRC255
+#define E1000_82542_PRC511 E1000_PRC511
+#define E1000_82542_PRC1023 E1000_PRC1023
+#define E1000_82542_PRC1522 E1000_PRC1522
+#define E1000_82542_GPRC E1000_GPRC
+#define E1000_82542_BPRC E1000_BPRC
+#define E1000_82542_MPRC E1000_MPRC
+#define E1000_82542_GPTC E1000_GPTC
+#define E1000_82542_GORCL E1000_GORCL
+#define E1000_82542_GORCH E1000_GORCH
+#define E1000_82542_GOTCL E1000_GOTCL
+#define E1000_82542_GOTCH E1000_GOTCH
+#define E1000_82542_RNBC E1000_RNBC
+#define E1000_82542_RUC E1000_RUC
+#define E1000_82542_RFC E1000_RFC
+#define E1000_82542_ROC E1000_ROC
+#define E1000_82542_RJC E1000_RJC
+#define E1000_82542_MGTPRC E1000_MGTPRC
+#define E1000_82542_MGTPDC E1000_MGTPDC
+#define E1000_82542_MGTPTC E1000_MGTPTC
+#define E1000_82542_TORL E1000_TORL
+#define E1000_82542_TORH E1000_TORH
+#define E1000_82542_TOTL E1000_TOTL
+#define E1000_82542_TOTH E1000_TOTH
+#define E1000_82542_TPR E1000_TPR
+#define E1000_82542_TPT E1000_TPT
+#define E1000_82542_PTC64 E1000_PTC64
+#define E1000_82542_PTC127 E1000_PTC127
+#define E1000_82542_PTC255 E1000_PTC255
+#define E1000_82542_PTC511 E1000_PTC511
+#define E1000_82542_PTC1023 E1000_PTC1023
+#define E1000_82542_PTC1522 E1000_PTC1522
+#define E1000_82542_MPTC E1000_MPTC
+#define E1000_82542_BPTC E1000_BPTC
+#define E1000_82542_TSCTC E1000_TSCTC
+#define E1000_82542_TSCTFC E1000_TSCTFC
+#define E1000_82542_RXCSUM E1000_RXCSUM
+#define E1000_82542_WUC E1000_WUC
+#define E1000_82542_WUFC E1000_WUFC
+#define E1000_82542_WUS E1000_WUS
+#define E1000_82542_MANC E1000_MANC
+#define E1000_82542_IPAV E1000_IPAV
+#define E1000_82542_IP4AT E1000_IP4AT
+#define E1000_82542_IP6AT E1000_IP6AT
+#define E1000_82542_WUPL E1000_WUPL
+#define E1000_82542_WUPM E1000_WUPM
+#define E1000_82542_FFLT E1000_FFLT
+#define E1000_82542_TDFH 0x08010
+#define E1000_82542_TDFT 0x08018
+#define E1000_82542_FFMT E1000_FFMT
+#define E1000_82542_FFVT E1000_FFVT
+#define E1000_82542_HOST_IF E1000_HOST_IF
+#define E1000_82542_IAM E1000_IAM
+#define E1000_82542_EEMNGCTL E1000_EEMNGCTL
+#define E1000_82542_PSRCTL E1000_PSRCTL
+#define E1000_82542_RAID E1000_RAID
+#define E1000_82542_TARC0 E1000_TARC0
+#define E1000_82542_TDBAL1 E1000_TDBAL1
+#define E1000_82542_TDBAH1 E1000_TDBAH1
+#define E1000_82542_TDLEN1 E1000_TDLEN1
+#define E1000_82542_TDH1 E1000_TDH1
+#define E1000_82542_TDT1 E1000_TDT1
+#define E1000_82542_TXDCTL1 E1000_TXDCTL1
+#define E1000_82542_TARC1 E1000_TARC1
+#define E1000_82542_RFCTL E1000_RFCTL
+#define E1000_82542_GCR E1000_GCR
+#define E1000_82542_GSCL_1 E1000_GSCL_1
+#define E1000_82542_GSCL_2 E1000_GSCL_2
+#define E1000_82542_GSCL_3 E1000_GSCL_3
+#define E1000_82542_GSCL_4 E1000_GSCL_4
+#define E1000_82542_FACTPS E1000_FACTPS
+#define E1000_82542_SWSM E1000_SWSM
+#define E1000_82542_FWSM E1000_FWSM
+#define E1000_82542_FFLT_DBG E1000_FFLT_DBG
+#define E1000_82542_IAC E1000_IAC
+#define E1000_82542_ICRXPTC E1000_ICRXPTC
+#define E1000_82542_ICRXATC E1000_ICRXATC
+#define E1000_82542_ICTXPTC E1000_ICTXPTC
+#define E1000_82542_ICTXATC E1000_ICTXATC
+#define E1000_82542_ICTXQEC E1000_ICTXQEC
+#define E1000_82542_ICTXQMTC E1000_ICTXQMTC
+#define E1000_82542_ICRXDMTC E1000_ICRXDMTC
+#define E1000_82542_ICRXOC E1000_ICRXOC
+#define E1000_82542_HICR E1000_HICR
+
+#define E1000_82542_CPUVEC E1000_CPUVEC
+#define E1000_82542_MRQC E1000_MRQC
+#define E1000_82542_RETA E1000_RETA
+#define E1000_82542_RSSRK E1000_RSSRK
+#define E1000_82542_RSSIM E1000_RSSIM
+#define E1000_82542_RSSIR E1000_RSSIR
+#define E1000_82542_KUMCTRLSTA E1000_KUMCTRLSTA
+#define E1000_82542_SW_FW_SYNC E1000_SW_FW_SYNC
+
+/* Statistics counters collected by the MAC */
+struct e1000_hw_stats {
+ u64 crcerrs;
+ u64 algnerrc;
+ u64 symerrs;
+ u64 rxerrc;
+ u64 txerrc;
+ u64 mpc;
+ u64 scc;
+ u64 ecol;
+ u64 mcc;
+ u64 latecol;
+ u64 colc;
+ u64 dc;
+ u64 tncrs;
+ u64 sec;
+ u64 cexterr;
+ u64 rlec;
+ u64 xonrxc;
+ u64 xontxc;
+ u64 xoffrxc;
+ u64 xofftxc;
+ u64 fcruc;
+ u64 prc64;
+ u64 prc127;
+ u64 prc255;
+ u64 prc511;
+ u64 prc1023;
+ u64 prc1522;
+ u64 gprc;
+ u64 bprc;
+ u64 mprc;
+ u64 gptc;
+ u64 gorcl;
+ u64 gorch;
+ u64 gotcl;
+ u64 gotch;
+ u64 rnbc;
+ u64 ruc;
+ u64 rfc;
+ u64 roc;
+ u64 rlerrc;
+ u64 rjc;
+ u64 mgprc;
+ u64 mgpdc;
+ u64 mgptc;
+ u64 torl;
+ u64 torh;
+ u64 totl;
+ u64 toth;
+ u64 tpr;
+ u64 tpt;
+ u64 ptc64;
+ u64 ptc127;
+ u64 ptc255;
+ u64 ptc511;
+ u64 ptc1023;
+ u64 ptc1522;
+ u64 mptc;
+ u64 bptc;
+ u64 tsctc;
+ u64 tsctfc;
+ u64 iac;
+ u64 icrxptc;
+ u64 icrxatc;
+ u64 ictxptc;
+ u64 ictxatc;
+ u64 ictxqec;
+ u64 ictxqmtc;
+ u64 icrxdmtc;
+ u64 icrxoc;
+};
+
+/* Structure containing variables used by the shared code (e1000_hw.c) */
+struct e1000_hw {
+ u8 __iomem *hw_addr;
+ u8 __iomem *flash_address;
+ e1000_mac_type mac_type;
+ e1000_phy_type phy_type;
+ u32 phy_init_script;
+ e1000_media_type media_type;
+ void *back;
+ struct e1000_shadow_ram *eeprom_shadow_ram;
+ u32 flash_bank_size;
+ u32 flash_base_addr;
+ e1000_fc_type fc;
+ e1000_bus_speed bus_speed;
+ e1000_bus_width bus_width;
+ e1000_bus_type bus_type;
+ struct e1000_eeprom_info eeprom;
+ e1000_ms_type master_slave;
+ e1000_ms_type original_master_slave;
+ e1000_ffe_config ffe_config_state;
+ u32 asf_firmware_present;
+ u32 eeprom_semaphore_present;
+ unsigned long io_base;
+ u32 phy_id;
+ u32 phy_revision;
+ u32 phy_addr;
+ u32 original_fc;
+ u32 txcw;
+ u32 autoneg_failed;
+ u32 max_frame_size;
+ u32 min_frame_size;
+ u32 mc_filter_type;
+ u32 num_mc_addrs;
+ u32 collision_delta;
+ u32 tx_packet_delta;
+ u32 ledctl_default;
+ u32 ledctl_mode1;
+ u32 ledctl_mode2;
+ bool tx_pkt_filtering;
+ struct e1000_host_mng_dhcp_cookie mng_cookie;
+ u16 phy_spd_default;
+ u16 autoneg_advertised;
+ u16 pci_cmd_word;
+ u16 fc_high_water;
+ u16 fc_low_water;
+ u16 fc_pause_time;
+ u16 current_ifs_val;
+ u16 ifs_min_val;
+ u16 ifs_max_val;
+ u16 ifs_step_size;
+ u16 ifs_ratio;
+ u16 device_id;
+ u16 vendor_id;
+ u16 subsystem_id;
+ u16 subsystem_vendor_id;
+ u8 revision_id;
+ u8 autoneg;
+ u8 mdix;
+ u8 forced_speed_duplex;
+ u8 wait_autoneg_complete;
+ u8 dma_fairness;
+ u8 mac_addr[NODE_ADDRESS_SIZE];
+ u8 perm_mac_addr[NODE_ADDRESS_SIZE];
+ bool disable_polarity_correction;
+ bool speed_downgraded;
+ e1000_smart_speed smart_speed;
+ e1000_dsp_config dsp_config_state;
+ bool get_link_status;
+ bool serdes_has_link;
+ bool tbi_compatibility_en;
+ bool tbi_compatibility_on;
+ bool laa_is_present;
+ bool phy_reset_disable;
+ bool initialize_hw_bits_disable;
+ bool fc_send_xon;
+ bool fc_strict_ieee;
+ bool report_tx_early;
+ bool adaptive_ifs;
+ bool ifs_params_forced;
+ bool in_ifs_mode;
+ bool mng_reg_access_disabled;
+ bool leave_av_bit_off;
+ bool bad_tx_carr_stats_fd;
+ bool has_smbus;
+};
+
+#define E1000_EEPROM_SWDPIN0 0x0001 /* SWDPIN 0 EEPROM Value */
+#define E1000_EEPROM_LED_LOGIC 0x0020 /* Led Logic Word */
+#define E1000_EEPROM_RW_REG_DATA 16 /* Offset to data in EEPROM read/write registers */
+#define E1000_EEPROM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
+#define E1000_EEPROM_RW_REG_START 1 /* First bit for telling part to start operation */
+#define E1000_EEPROM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
+#define E1000_EEPROM_POLL_WRITE 1 /* Flag for polling for write complete */
+#define E1000_EEPROM_POLL_READ 0 /* Flag for polling for read complete */
+/* Register Bit Masks */
+/* Device Control */
+#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
+#define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */
+#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */
+#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
+#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
+#define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */
+#define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */
+#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
+#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
+#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
+#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
+#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */
+#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
+#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
+#define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */
+#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
+#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
+#define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */
+#define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock indication in SDP[0] */
+#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through PHYRST_N pin */
+#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external LINK_0 and LINK_1 pins */
+#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
+#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
+#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */
+#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */
+#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
+#define E1000_CTRL_SWDPIO1 0x00800000 /* SWDPIN 1 input or output */
+#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */
+#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */
+#define E1000_CTRL_RST 0x04000000 /* Global reset */
+#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
+#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
+#define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */
+#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
+#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
+#define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to manageability engine */
+
+/* Device Status */
+#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
+#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
+#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
+#define E1000_STATUS_FUNC_SHIFT 2
+#define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */
+#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
+#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
+#define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */
+#define E1000_STATUS_SPEED_MASK 0x000000C0
+#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
+#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
+#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
+#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion
+ by EEPROM/Flash */
+#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */
+#define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. Clear on write '0'. */
+#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
+#define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */
+#define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */
+#define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */
+#define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */
+#define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */
+#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */
+#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */
+#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */
+#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */
+#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution disabled */
+#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */
+#define E1000_STATUS_FUSE_8 0x04000000
+#define E1000_STATUS_FUSE_9 0x08000000
+#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */
+#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */
+
+/* Constants used to interpret the masked PCI-X bus speed. */
+#define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */
+#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed 66-100 MHz */
+#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /* PCI-X bus speed 100-133 MHz */
+
+/* EEPROM/Flash Control */
+#define E1000_EECD_SK 0x00000001 /* EEPROM Clock */
+#define E1000_EECD_CS 0x00000002 /* EEPROM Chip Select */
+#define E1000_EECD_DI 0x00000004 /* EEPROM Data In */
+#define E1000_EECD_DO 0x00000008 /* EEPROM Data Out */
+#define E1000_EECD_FWE_MASK 0x00000030
+#define E1000_EECD_FWE_DIS 0x00000010 /* Disable FLASH writes */
+#define E1000_EECD_FWE_EN 0x00000020 /* Enable FLASH writes */
+#define E1000_EECD_FWE_SHIFT 4
+#define E1000_EECD_REQ 0x00000040 /* EEPROM Access Request */
+#define E1000_EECD_GNT 0x00000080 /* EEPROM Access Grant */
+#define E1000_EECD_PRES 0x00000100 /* EEPROM Present */
+#define E1000_EECD_SIZE 0x00000200 /* EEPROM Size (0=64 word 1=256 word) */
+#define E1000_EECD_ADDR_BITS 0x00000400 /* EEPROM Addressing bits based on type
+ * (0-small, 1-large) */
+#define E1000_EECD_TYPE 0x00002000 /* EEPROM Type (1-SPI, 0-Microwire) */
+#ifndef E1000_EEPROM_GRANT_ATTEMPTS
+#define E1000_EEPROM_GRANT_ATTEMPTS 1000 /* EEPROM # attempts to gain grant */
+#endif
+#define E1000_EECD_AUTO_RD 0x00000200 /* EEPROM Auto Read done */
+#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* EEprom Size */
+#define E1000_EECD_SIZE_EX_SHIFT 11
+#define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */
+#define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */
+#define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */
+#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */
+#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */
+#define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */
+#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
+#define E1000_EECD_SECVAL_SHIFT 22
+#define E1000_STM_OPCODE 0xDB00
+#define E1000_HICR_FW_RESET 0xC0
+
+#define E1000_SHADOW_RAM_WORDS 2048
+#define E1000_ICH_NVM_SIG_WORD 0x13
+#define E1000_ICH_NVM_SIG_MASK 0xC0
+
+/* EEPROM Read */
+#define E1000_EERD_START 0x00000001 /* Start Read */
+#define E1000_EERD_DONE 0x00000010 /* Read Done */
+#define E1000_EERD_ADDR_SHIFT 8
+#define E1000_EERD_ADDR_MASK 0x0000FF00 /* Read Address */
+#define E1000_EERD_DATA_SHIFT 16
+#define E1000_EERD_DATA_MASK 0xFFFF0000 /* Read Data */
+
+/* SPI EEPROM Status Register */
+#define EEPROM_STATUS_RDY_SPI 0x01
+#define EEPROM_STATUS_WEN_SPI 0x02
+#define EEPROM_STATUS_BP0_SPI 0x04
+#define EEPROM_STATUS_BP1_SPI 0x08
+#define EEPROM_STATUS_WPEN_SPI 0x80
+
+/* Extended Device Control */
+#define E1000_CTRL_EXT_GPI0_EN 0x00000001 /* Maps SDP4 to GPI0 */
+#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */
+#define E1000_CTRL_EXT_PHYINT_EN E1000_CTRL_EXT_GPI1_EN
+#define E1000_CTRL_EXT_GPI2_EN 0x00000004 /* Maps SDP6 to GPI2 */
+#define E1000_CTRL_EXT_GPI3_EN 0x00000008 /* Maps SDP7 to GPI3 */
+#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable Pin 4 */
+#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable Pin 5 */
+#define E1000_CTRL_EXT_PHY_INT E1000_CTRL_EXT_SDP5_DATA
+#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Defineable Pin 6 */
+#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
+#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */
+#define E1000_CTRL_EXT_SDP5_DIR 0x00000200 /* Direction of SDP5 0=in 1=out */
+#define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */
+#define E1000_CTRL_EXT_SDP7_DIR 0x00000800 /* Direction of SDP7 0=in 1=out */
+#define E1000_CTRL_EXT_ASDCHK 0x00001000 /* Initiate an ASD sequence */
+#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
+#define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */
+#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
+#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
+#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000
+#define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_KMRN 0x00000000
+#define E1000_CTRL_EXT_LINK_MODE_SERDES 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000
+#define E1000_CTRL_EXT_WR_WMARK_MASK 0x03000000
+#define E1000_CTRL_EXT_WR_WMARK_256 0x00000000
+#define E1000_CTRL_EXT_WR_WMARK_320 0x01000000
+#define E1000_CTRL_EXT_WR_WMARK_384 0x02000000
+#define E1000_CTRL_EXT_WR_WMARK_448 0x03000000
+#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
+#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
+#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
+#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error detection enabled */
+#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity error detection enable */
+#define E1000_CTRL_EXT_GHOST_PAREN 0x40000000
+
+/* MDI Control */
+#define E1000_MDIC_DATA_MASK 0x0000FFFF
+#define E1000_MDIC_REG_MASK 0x001F0000
+#define E1000_MDIC_REG_SHIFT 16
+#define E1000_MDIC_PHY_MASK 0x03E00000
+#define E1000_MDIC_PHY_SHIFT 21
+#define E1000_MDIC_OP_WRITE 0x04000000
+#define E1000_MDIC_OP_READ 0x08000000
+#define E1000_MDIC_READY 0x10000000
+#define E1000_MDIC_INT_EN 0x20000000
+#define E1000_MDIC_ERROR 0x40000000
+
+#define E1000_KUMCTRLSTA_MASK 0x0000FFFF
+#define E1000_KUMCTRLSTA_OFFSET 0x001F0000
+#define E1000_KUMCTRLSTA_OFFSET_SHIFT 16
+#define E1000_KUMCTRLSTA_REN 0x00200000
+
+#define E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL 0x00000000
+#define E1000_KUMCTRLSTA_OFFSET_CTRL 0x00000001
+#define E1000_KUMCTRLSTA_OFFSET_INB_CTRL 0x00000002
+#define E1000_KUMCTRLSTA_OFFSET_DIAG 0x00000003
+#define E1000_KUMCTRLSTA_OFFSET_TIMEOUTS 0x00000004
+#define E1000_KUMCTRLSTA_OFFSET_INB_PARAM 0x00000009
+#define E1000_KUMCTRLSTA_OFFSET_HD_CTRL 0x00000010
+#define E1000_KUMCTRLSTA_OFFSET_M2P_SERDES 0x0000001E
+#define E1000_KUMCTRLSTA_OFFSET_M2P_MODES 0x0000001F
+
+/* FIFO Control */
+#define E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS 0x00000008
+#define E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS 0x00000800
+
+/* In-Band Control */
+#define E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT 0x00000500
+#define E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING 0x00000010
+
+/* Half-Duplex Control */
+#define E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT 0x00000004
+#define E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT 0x00000000
+
+#define E1000_KUMCTRLSTA_OFFSET_K0S_CTRL 0x0000001E
+
+#define E1000_KUMCTRLSTA_DIAG_FELPBK 0x2000
+#define E1000_KUMCTRLSTA_DIAG_NELPBK 0x1000
+
+#define E1000_KUMCTRLSTA_K0S_100_EN 0x2000
+#define E1000_KUMCTRLSTA_K0S_GBE_EN 0x1000
+#define E1000_KUMCTRLSTA_K0S_ENTRY_LATENCY_MASK 0x0003
+
+#define E1000_KABGTXD_BGSQLBIAS 0x00050000
+
+#define E1000_PHY_CTRL_SPD_EN 0x00000001
+#define E1000_PHY_CTRL_D0A_LPLU 0x00000002
+#define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004
+#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008
+#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040
+#define E1000_PHY_CTRL_B2B_EN 0x00000080
+
+/* LED Control */
+#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
+#define E1000_LEDCTL_LED0_MODE_SHIFT 0
+#define E1000_LEDCTL_LED0_BLINK_RATE 0x0000020
+#define E1000_LEDCTL_LED0_IVRT 0x00000040
+#define E1000_LEDCTL_LED0_BLINK 0x00000080
+#define E1000_LEDCTL_LED1_MODE_MASK 0x00000F00
+#define E1000_LEDCTL_LED1_MODE_SHIFT 8
+#define E1000_LEDCTL_LED1_BLINK_RATE 0x0002000
+#define E1000_LEDCTL_LED1_IVRT 0x00004000
+#define E1000_LEDCTL_LED1_BLINK 0x00008000
+#define E1000_LEDCTL_LED2_MODE_MASK 0x000F0000
+#define E1000_LEDCTL_LED2_MODE_SHIFT 16
+#define E1000_LEDCTL_LED2_BLINK_RATE 0x00200000
+#define E1000_LEDCTL_LED2_IVRT 0x00400000
+#define E1000_LEDCTL_LED2_BLINK 0x00800000
+#define E1000_LEDCTL_LED3_MODE_MASK 0x0F000000
+#define E1000_LEDCTL_LED3_MODE_SHIFT 24
+#define E1000_LEDCTL_LED3_BLINK_RATE 0x20000000
+#define E1000_LEDCTL_LED3_IVRT 0x40000000
+#define E1000_LEDCTL_LED3_BLINK 0x80000000
+
+#define E1000_LEDCTL_MODE_LINK_10_1000 0x0
+#define E1000_LEDCTL_MODE_LINK_100_1000 0x1
+#define E1000_LEDCTL_MODE_LINK_UP 0x2
+#define E1000_LEDCTL_MODE_ACTIVITY 0x3
+#define E1000_LEDCTL_MODE_LINK_ACTIVITY 0x4
+#define E1000_LEDCTL_MODE_LINK_10 0x5
+#define E1000_LEDCTL_MODE_LINK_100 0x6
+#define E1000_LEDCTL_MODE_LINK_1000 0x7
+#define E1000_LEDCTL_MODE_PCIX_MODE 0x8
+#define E1000_LEDCTL_MODE_FULL_DUPLEX 0x9
+#define E1000_LEDCTL_MODE_COLLISION 0xA
+#define E1000_LEDCTL_MODE_BUS_SPEED 0xB
+#define E1000_LEDCTL_MODE_BUS_SIZE 0xC
+#define E1000_LEDCTL_MODE_PAUSED 0xD
+#define E1000_LEDCTL_MODE_LED_ON 0xE
+#define E1000_LEDCTL_MODE_LED_OFF 0xF
+
+/* Receive Address */
+#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
+
+/* Interrupt Cause Read */
+#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
+#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */
+#define E1000_ICR_LSC 0x00000004 /* Link Status Change */
+#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
+#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
+#define E1000_ICR_RXO 0x00000040 /* rx overrun */
+#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
+#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */
+#define E1000_ICR_RXCFG 0x00000400 /* RX /c/ ordered set */
+#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */
+#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */
+#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */
+#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */
+#define E1000_ICR_TXD_LOW 0x00008000
+#define E1000_ICR_SRPD 0x00010000
+#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */
+#define E1000_ICR_MNG 0x00040000 /* Manageability event */
+#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */
+#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */
+#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity error */
+#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */
+#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */
+#define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW bit in the FWSM */
+#define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates an interrupt */
+#define E1000_ICR_EPRST 0x00100000 /* ME hardware reset occurs */
+
+/* Interrupt Cause Set */
+#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW
+#define E1000_ICS_SRPD E1000_ICR_SRPD
+#define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_ICS_DSW E1000_ICR_DSW
+#define E1000_ICS_PHYINT E1000_ICR_PHYINT
+#define E1000_ICS_EPRST E1000_ICR_EPRST
+
+/* Interrupt Mask Set */
+#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW
+#define E1000_IMS_SRPD E1000_ICR_SRPD
+#define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_IMS_DSW E1000_ICR_DSW
+#define E1000_IMS_PHYINT E1000_ICR_PHYINT
+#define E1000_IMS_EPRST E1000_ICR_EPRST
+
+/* Interrupt Mask Clear */
+#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_IMC_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_IMC_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_IMC_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_IMC_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_IMC_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_IMC_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_IMC_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_IMC_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_IMC_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_IMC_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_IMC_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_IMC_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_IMC_TXD_LOW E1000_ICR_TXD_LOW
+#define E1000_IMC_SRPD E1000_ICR_SRPD
+#define E1000_IMC_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_IMC_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_IMC_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_IMC_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_IMC_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_IMC_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_IMC_DSW E1000_ICR_DSW
+#define E1000_IMC_PHYINT E1000_ICR_PHYINT
+#define E1000_IMC_EPRST E1000_ICR_EPRST
+
+/* Receive Control */
+#define E1000_RCTL_RST 0x00000001 /* Software reset */
+#define E1000_RCTL_EN 0x00000002 /* enable */
+#define E1000_RCTL_SBP 0x00000004 /* store bad packet */
+#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
+#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
+#define E1000_RCTL_LPE 0x00000020 /* long packet enable */
+#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
+#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
+#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */
+#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
+#define E1000_RCTL_DTYP_MASK 0x00000C00 /* Descriptor type mask */
+#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
+#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
+#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */
+#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */
+#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
+#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */
+#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */
+#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */
+#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
+#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */
+#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
+/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
+#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */
+#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */
+#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
+#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
+/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
+#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */
+#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */
+#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */
+#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
+#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
+#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
+#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */
+#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
+#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
+#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
+#define E1000_RCTL_FLXBUF_MASK 0x78000000 /* Flexible buffer size */
+#define E1000_RCTL_FLXBUF_SHIFT 27 /* Flexible buffer shift */
+
+/* Use byte values for the following shift parameters
+ * Usage:
+ * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
+ * E1000_PSRCTL_BSIZE0_MASK) |
+ * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
+ * E1000_PSRCTL_BSIZE1_MASK) |
+ * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
+ * E1000_PSRCTL_BSIZE2_MASK) |
+ * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
+ * E1000_PSRCTL_BSIZE3_MASK))
+ * where value0 = [128..16256], default=256
+ * value1 = [1024..64512], default=4096
+ * value2 = [0..64512], default=4096
+ * value3 = [0..64512], default=0
+ */
+
+#define E1000_PSRCTL_BSIZE0_MASK 0x0000007F
+#define E1000_PSRCTL_BSIZE1_MASK 0x00003F00
+#define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
+#define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
+
+#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
+#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
+#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
+#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
+
+/* SW_W_SYNC definitions */
+#define E1000_SWFW_EEP_SM 0x0001
+#define E1000_SWFW_PHY0_SM 0x0002
+#define E1000_SWFW_PHY1_SM 0x0004
+#define E1000_SWFW_MAC_CSR_SM 0x0008
+
+/* Receive Descriptor */
+#define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */
+#define E1000_RDT_FPDB 0x80000000 /* Flush descriptor block */
+#define E1000_RDLEN_LEN 0x0007ff80 /* descriptor length */
+#define E1000_RDH_RDH 0x0000ffff /* receive descriptor head */
+#define E1000_RDT_RDT 0x0000ffff /* receive descriptor tail */
+
+/* Flow Control */
+#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */
+#define E1000_FCRTH_XFCE 0x80000000 /* External Flow Control Enable */
+#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */
+#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
+
+/* Header split receive */
+#define E1000_RFCTL_ISCSI_DIS 0x00000001
+#define E1000_RFCTL_ISCSI_DWC_MASK 0x0000003E
+#define E1000_RFCTL_ISCSI_DWC_SHIFT 1
+#define E1000_RFCTL_NFSW_DIS 0x00000040
+#define E1000_RFCTL_NFSR_DIS 0x00000080
+#define E1000_RFCTL_NFS_VER_MASK 0x00000300
+#define E1000_RFCTL_NFS_VER_SHIFT 8
+#define E1000_RFCTL_IPV6_DIS 0x00000400
+#define E1000_RFCTL_IPV6_XSUM_DIS 0x00000800
+#define E1000_RFCTL_ACK_DIS 0x00001000
+#define E1000_RFCTL_ACKD_DIS 0x00002000
+#define E1000_RFCTL_IPFRSP_DIS 0x00004000
+#define E1000_RFCTL_EXTEN 0x00008000
+#define E1000_RFCTL_IPV6_EX_DIS 0x00010000
+#define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000
+
+/* Receive Descriptor Control */
+#define E1000_RXDCTL_PTHRESH 0x0000003F /* RXDCTL Prefetch Threshold */
+#define E1000_RXDCTL_HTHRESH 0x00003F00 /* RXDCTL Host Threshold */
+#define E1000_RXDCTL_WTHRESH 0x003F0000 /* RXDCTL Writeback Threshold */
+#define E1000_RXDCTL_GRAN 0x01000000 /* RXDCTL Granularity */
+
+/* Transmit Descriptor Control */
+#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */
+#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */
+#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */
+#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */
+#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */
+#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
+#define E1000_TXDCTL_COUNT_DESC 0x00400000 /* Enable the counting of desc.
+ still to be processed. */
+/* Transmit Configuration Word */
+#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */
+#define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */
+#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
+#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
+#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */
+#define E1000_TXCW_RF 0x00003000 /* TXCW remote fault */
+#define E1000_TXCW_NP 0x00008000 /* TXCW next page */
+#define E1000_TXCW_CW 0x0000ffff /* TxConfigWord mask */
+#define E1000_TXCW_TXC 0x40000000 /* Transmit Config control */
+#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
+
+/* Receive Configuration Word */
+#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */
+#define E1000_RXCW_NC 0x04000000 /* Receive config no carrier */
+#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */
+#define E1000_RXCW_CC 0x10000000 /* Receive config change */
+#define E1000_RXCW_C 0x20000000 /* Receive config */
+#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */
+#define E1000_RXCW_ANC 0x80000000 /* Auto-neg complete */
+
+/* Transmit Control */
+#define E1000_TCTL_RST 0x00000001 /* software reset */
+#define E1000_TCTL_EN 0x00000002 /* enable tx */
+#define E1000_TCTL_BCE 0x00000004 /* busy check enable */
+#define E1000_TCTL_PSP 0x00000008 /* pad short packets */
+#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
+#define E1000_TCTL_COLD 0x003ff000 /* collision distance */
+#define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */
+#define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */
+#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
+#define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */
+#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
+/* Extended Transmit Control */
+#define E1000_TCTL_EXT_BST_MASK 0x000003FF /* Backoff Slot Time */
+#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
+
+/* Receive Checksum Control */
+#define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */
+#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */
+#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
+#define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */
+#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
+#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
+
+/* Multiple Receive Queue Control */
+#define E1000_MRQC_ENABLE_MASK 0x00000003
+#define E1000_MRQC_ENABLE_RSS_2Q 0x00000001
+#define E1000_MRQC_ENABLE_RSS_INT 0x00000004
+#define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000
+#define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
+#define E1000_MRQC_RSS_FIELD_IPV4 0x00020000
+#define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000
+#define E1000_MRQC_RSS_FIELD_IPV6_EX 0x00080000
+#define E1000_MRQC_RSS_FIELD_IPV6 0x00100000
+#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000
+
+/* Definitions for power management and wakeup registers */
+/* Wake Up Control */
+#define E1000_WUC_APME 0x00000001 /* APM Enable */
+#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
+#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */
+#define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */
+#define E1000_WUC_SPM 0x80000000 /* Enable SPM */
+
+/* Wake Up Filter Control */
+#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
+#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
+#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
+#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
+#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
+#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
+#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */
+#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */
+#define E1000_WUFC_IGNORE_TCO 0x00008000 /* Ignore WakeOn TCO packets */
+#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */
+#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */
+#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */
+#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */
+#define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */
+#define E1000_WUFC_FLX_OFFSET 16 /* Offset to the Flexible Filters bits */
+#define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
+
+/* Wake Up Status */
+#define E1000_WUS_LNKC 0x00000001 /* Link Status Changed */
+#define E1000_WUS_MAG 0x00000002 /* Magic Packet Received */
+#define E1000_WUS_EX 0x00000004 /* Directed Exact Received */
+#define E1000_WUS_MC 0x00000008 /* Directed Multicast Received */
+#define E1000_WUS_BC 0x00000010 /* Broadcast Received */
+#define E1000_WUS_ARP 0x00000020 /* ARP Request Packet Received */
+#define E1000_WUS_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Received */
+#define E1000_WUS_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Received */
+#define E1000_WUS_FLX0 0x00010000 /* Flexible Filter 0 Match */
+#define E1000_WUS_FLX1 0x00020000 /* Flexible Filter 1 Match */
+#define E1000_WUS_FLX2 0x00040000 /* Flexible Filter 2 Match */
+#define E1000_WUS_FLX3 0x00080000 /* Flexible Filter 3 Match */
+#define E1000_WUS_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
+
+/* Management Control */
+#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
+#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
+#define E1000_MANC_R_ON_FORCE 0x00000004 /* Reset on Force TCO - RO */
+#define E1000_MANC_RMCP_EN 0x00000100 /* Enable RCMP 026Fh Filtering */
+#define E1000_MANC_0298_EN 0x00000200 /* Enable RCMP 0298h Filtering */
+#define E1000_MANC_IPV4_EN 0x00000400 /* Enable IPv4 */
+#define E1000_MANC_IPV6_EN 0x00000800 /* Enable IPv6 */
+#define E1000_MANC_SNAP_EN 0x00001000 /* Accept LLC/SNAP */
+#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
+#define E1000_MANC_NEIGHBOR_EN 0x00004000 /* Enable Neighbor Discovery
+ * Filtering */
+#define E1000_MANC_ARP_RES_EN 0x00008000 /* Enable ARP response Filtering */
+#define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */
+#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
+#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */
+#define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */
+#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
+#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 /* Enable MAC address
+ * filtering */
+#define E1000_MANC_EN_MNG2HOST 0x00200000 /* Enable MNG packets to host
+ * memory */
+#define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000 /* Enable IP address
+ * filtering */
+#define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */
+#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */
+#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */
+#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */
+#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */
+#define E1000_MANC_SMB_DATA_IN 0x08000000 /* SMBus Data In */
+#define E1000_MANC_SMB_DATA_OUT 0x10000000 /* SMBus Data Out */
+#define E1000_MANC_SMB_CLK_OUT 0x20000000 /* SMBus Clock Out */
+
+#define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */
+#define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */
+
+/* SW Semaphore Register */
+#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
+#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
+#define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */
+#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */
+
+/* FW Semaphore Register */
+#define E1000_FWSM_MODE_MASK 0x0000000E /* FW mode */
+#define E1000_FWSM_MODE_SHIFT 1
+#define E1000_FWSM_FW_VALID 0x00008000 /* FW established a valid mode */
+
+#define E1000_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI reset */
+#define E1000_FWSM_DISSW 0x10000000 /* FW disable SW Write Access */
+#define E1000_FWSM_SKUSEL_MASK 0x60000000 /* LAN SKU select */
+#define E1000_FWSM_SKUEL_SHIFT 29
+#define E1000_FWSM_SKUSEL_EMB 0x0 /* Embedded SKU */
+#define E1000_FWSM_SKUSEL_CONS 0x1 /* Consumer SKU */
+#define E1000_FWSM_SKUSEL_PERF_100 0x2 /* Perf & Corp 10/100 SKU */
+#define E1000_FWSM_SKUSEL_PERF_GBE 0x3 /* Perf & Copr GbE SKU */
+
+/* FFLT Debug Register */
+#define E1000_FFLT_DBG_INVC 0x00100000 /* Invalid /C/ code handling */
+
+typedef enum {
+ e1000_mng_mode_none = 0,
+ e1000_mng_mode_asf,
+ e1000_mng_mode_pt,
+ e1000_mng_mode_ipmi,
+ e1000_mng_mode_host_interface_only
+} e1000_mng_mode;
+
+/* Host Interface Control Register */
+#define E1000_HICR_EN 0x00000001 /* Enable Bit - RO */
+#define E1000_HICR_C 0x00000002 /* Driver sets this bit when done
+ * to put command in RAM */
+#define E1000_HICR_SV 0x00000004 /* Status Validity */
+#define E1000_HICR_FWR 0x00000080 /* FW reset. Set by the Host */
+
+/* Host Interface Command Interface - Address range 0x8800-0x8EFF */
+#define E1000_HI_MAX_DATA_LENGTH 252 /* Host Interface data length */
+#define E1000_HI_MAX_BLOCK_BYTE_LENGTH 1792 /* Number of bytes in range */
+#define E1000_HI_MAX_BLOCK_DWORD_LENGTH 448 /* Number of dwords in range */
+#define E1000_HI_COMMAND_TIMEOUT 500 /* Time in ms to process HI command */
+
+struct e1000_host_command_header {
+ u8 command_id;
+ u8 command_length;
+ u8 command_options; /* I/F bits for command, status for return */
+ u8 checksum;
+};
+struct e1000_host_command_info {
+ struct e1000_host_command_header command_header; /* Command Head/Command Result Head has 4 bytes */
+ u8 command_data[E1000_HI_MAX_DATA_LENGTH]; /* Command data can length 0..252 */
+};
+
+/* Host SMB register #0 */
+#define E1000_HSMC0R_CLKIN 0x00000001 /* SMB Clock in */
+#define E1000_HSMC0R_DATAIN 0x00000002 /* SMB Data in */
+#define E1000_HSMC0R_DATAOUT 0x00000004 /* SMB Data out */
+#define E1000_HSMC0R_CLKOUT 0x00000008 /* SMB Clock out */
+
+/* Host SMB register #1 */
+#define E1000_HSMC1R_CLKIN E1000_HSMC0R_CLKIN
+#define E1000_HSMC1R_DATAIN E1000_HSMC0R_DATAIN
+#define E1000_HSMC1R_DATAOUT E1000_HSMC0R_DATAOUT
+#define E1000_HSMC1R_CLKOUT E1000_HSMC0R_CLKOUT
+
+/* FW Status Register */
+#define E1000_FWSTS_FWS_MASK 0x000000FF /* FW Status */
+
+/* Wake Up Packet Length */
+#define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */
+
+#define E1000_MDALIGN 4096
+
+/* PCI-Ex registers*/
+
+/* PCI-Ex Control Register */
+#define E1000_GCR_RXD_NO_SNOOP 0x00000001
+#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002
+#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004
+#define E1000_GCR_TXD_NO_SNOOP 0x00000008
+#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010
+#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020
+
+#define PCI_EX_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \
+ E1000_GCR_RXDSCW_NO_SNOOP | \
+ E1000_GCR_RXDSCR_NO_SNOOP | \
+ E1000_GCR_TXD_NO_SNOOP | \
+ E1000_GCR_TXDSCW_NO_SNOOP | \
+ E1000_GCR_TXDSCR_NO_SNOOP)
+
+#define PCI_EX_82566_SNOOP_ALL PCI_EX_NO_SNOOP_ALL
+
+#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
+/* Function Active and Power State to MNG */
+#define E1000_FACTPS_FUNC0_POWER_STATE_MASK 0x00000003
+#define E1000_FACTPS_LAN0_VALID 0x00000004
+#define E1000_FACTPS_FUNC0_AUX_EN 0x00000008
+#define E1000_FACTPS_FUNC1_POWER_STATE_MASK 0x000000C0
+#define E1000_FACTPS_FUNC1_POWER_STATE_SHIFT 6
+#define E1000_FACTPS_LAN1_VALID 0x00000100
+#define E1000_FACTPS_FUNC1_AUX_EN 0x00000200
+#define E1000_FACTPS_FUNC2_POWER_STATE_MASK 0x00003000
+#define E1000_FACTPS_FUNC2_POWER_STATE_SHIFT 12
+#define E1000_FACTPS_IDE_ENABLE 0x00004000
+#define E1000_FACTPS_FUNC2_AUX_EN 0x00008000
+#define E1000_FACTPS_FUNC3_POWER_STATE_MASK 0x000C0000
+#define E1000_FACTPS_FUNC3_POWER_STATE_SHIFT 18
+#define E1000_FACTPS_SP_ENABLE 0x00100000
+#define E1000_FACTPS_FUNC3_AUX_EN 0x00200000
+#define E1000_FACTPS_FUNC4_POWER_STATE_MASK 0x03000000
+#define E1000_FACTPS_FUNC4_POWER_STATE_SHIFT 24
+#define E1000_FACTPS_IPMI_ENABLE 0x04000000
+#define E1000_FACTPS_FUNC4_AUX_EN 0x08000000
+#define E1000_FACTPS_MNGCG 0x20000000
+#define E1000_FACTPS_LAN_FUNC_SEL 0x40000000
+#define E1000_FACTPS_PM_STATE_CHANGED 0x80000000
+
+/* PCI-Ex Config Space */
+#define PCI_EX_LINK_STATUS 0x12
+#define PCI_EX_LINK_WIDTH_MASK 0x3F0
+#define PCI_EX_LINK_WIDTH_SHIFT 4
+
+/* EEPROM Commands - Microwire */
+#define EEPROM_READ_OPCODE_MICROWIRE 0x6 /* EEPROM read opcode */
+#define EEPROM_WRITE_OPCODE_MICROWIRE 0x5 /* EEPROM write opcode */
+#define EEPROM_ERASE_OPCODE_MICROWIRE 0x7 /* EEPROM erase opcode */
+#define EEPROM_EWEN_OPCODE_MICROWIRE 0x13 /* EEPROM erase/write enable */
+#define EEPROM_EWDS_OPCODE_MICROWIRE 0x10 /* EEPROM erase/write disable */
+
+/* EEPROM Commands - SPI */
+#define EEPROM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
+#define EEPROM_READ_OPCODE_SPI 0x03 /* EEPROM read opcode */
+#define EEPROM_WRITE_OPCODE_SPI 0x02 /* EEPROM write opcode */
+#define EEPROM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
+#define EEPROM_WREN_OPCODE_SPI 0x06 /* EEPROM set Write Enable latch */
+#define EEPROM_WRDI_OPCODE_SPI 0x04 /* EEPROM reset Write Enable latch */
+#define EEPROM_RDSR_OPCODE_SPI 0x05 /* EEPROM read Status register */
+#define EEPROM_WRSR_OPCODE_SPI 0x01 /* EEPROM write Status register */
+#define EEPROM_ERASE4K_OPCODE_SPI 0x20 /* EEPROM ERASE 4KB */
+#define EEPROM_ERASE64K_OPCODE_SPI 0xD8 /* EEPROM ERASE 64KB */
+#define EEPROM_ERASE256_OPCODE_SPI 0xDB /* EEPROM ERASE 256B */
+
+/* EEPROM Size definitions */
+#define EEPROM_WORD_SIZE_SHIFT 6
+#define EEPROM_SIZE_SHIFT 10
+#define EEPROM_SIZE_MASK 0x1C00
+
+/* EEPROM Word Offsets */
+#define EEPROM_COMPAT 0x0003
+#define EEPROM_ID_LED_SETTINGS 0x0004
+#define EEPROM_VERSION 0x0005
+#define EEPROM_SERDES_AMPLITUDE 0x0006 /* For SERDES output amplitude adjustment. */
+#define EEPROM_PHY_CLASS_WORD 0x0007
+#define EEPROM_INIT_CONTROL1_REG 0x000A
+#define EEPROM_INIT_CONTROL2_REG 0x000F
+#define EEPROM_SWDEF_PINS_CTRL_PORT_1 0x0010
+#define EEPROM_INIT_CONTROL3_PORT_B 0x0014
+#define EEPROM_INIT_3GIO_3 0x001A
+#define EEPROM_SWDEF_PINS_CTRL_PORT_0 0x0020
+#define EEPROM_INIT_CONTROL3_PORT_A 0x0024
+#define EEPROM_CFG 0x0012
+#define EEPROM_FLASH_VERSION 0x0032
+#define EEPROM_CHECKSUM_REG 0x003F
+
+#define E1000_EEPROM_CFG_DONE 0x00040000 /* MNG config cycle done */
+#define E1000_EEPROM_CFG_DONE_PORT_1 0x00080000 /* ...for second port */
+
+/* Word definitions for ID LED Settings */
+#define ID_LED_RESERVED_0000 0x0000
+#define ID_LED_RESERVED_FFFF 0xFFFF
+#define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
+ (ID_LED_OFF1_OFF2 << 8) | \
+ (ID_LED_DEF1_DEF2 << 4) | \
+ (ID_LED_DEF1_DEF2))
+#define ID_LED_DEF1_DEF2 0x1
+#define ID_LED_DEF1_ON2 0x2
+#define ID_LED_DEF1_OFF2 0x3
+#define ID_LED_ON1_DEF2 0x4
+#define ID_LED_ON1_ON2 0x5
+#define ID_LED_ON1_OFF2 0x6
+#define ID_LED_OFF1_DEF2 0x7
+#define ID_LED_OFF1_ON2 0x8
+#define ID_LED_OFF1_OFF2 0x9
+
+#define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF
+#define IGP_ACTIVITY_LED_ENABLE 0x0300
+#define IGP_LED3_MODE 0x07000000
+
+/* Mask bits for SERDES amplitude adjustment in Word 6 of the EEPROM */
+#define EEPROM_SERDES_AMPLITUDE_MASK 0x000F
+
+/* Mask bit for PHY class in Word 7 of the EEPROM */
+#define EEPROM_PHY_CLASS_A 0x8000
+
+/* Mask bits for fields in Word 0x0a of the EEPROM */
+#define EEPROM_WORD0A_ILOS 0x0010
+#define EEPROM_WORD0A_SWDPIO 0x01E0
+#define EEPROM_WORD0A_LRST 0x0200
+#define EEPROM_WORD0A_FD 0x0400
+#define EEPROM_WORD0A_66MHZ 0x0800
+
+/* Mask bits for fields in Word 0x0f of the EEPROM */
+#define EEPROM_WORD0F_PAUSE_MASK 0x3000
+#define EEPROM_WORD0F_PAUSE 0x1000
+#define EEPROM_WORD0F_ASM_DIR 0x2000
+#define EEPROM_WORD0F_ANE 0x0800
+#define EEPROM_WORD0F_SWPDIO_EXT 0x00F0
+#define EEPROM_WORD0F_LPLU 0x0001
+
+/* Mask bits for fields in Word 0x10/0x20 of the EEPROM */
+#define EEPROM_WORD1020_GIGA_DISABLE 0x0010
+#define EEPROM_WORD1020_GIGA_DISABLE_NON_D0A 0x0008
+
+/* Mask bits for fields in Word 0x1a of the EEPROM */
+#define EEPROM_WORD1A_ASPM_MASK 0x000C
+
+/* For checksumming, the sum of all words in the EEPROM should equal 0xBABA. */
+#define EEPROM_SUM 0xBABA
+
+/* EEPROM Map defines (WORD OFFSETS)*/
+#define EEPROM_NODE_ADDRESS_BYTE_0 0
+#define EEPROM_PBA_BYTE_1 8
+
+#define EEPROM_RESERVED_WORD 0xFFFF
+
+/* EEPROM Map Sizes (Byte Counts) */
+#define PBA_SIZE 4
+
+/* Collision related configuration parameters */
+#define E1000_COLLISION_THRESHOLD 15
+#define E1000_CT_SHIFT 4
+/* Collision distance is a 0-based value that applies to
+ * half-duplex-capable hardware only. */
+#define E1000_COLLISION_DISTANCE 63
+#define E1000_COLLISION_DISTANCE_82542 64
+#define E1000_FDX_COLLISION_DISTANCE E1000_COLLISION_DISTANCE
+#define E1000_HDX_COLLISION_DISTANCE E1000_COLLISION_DISTANCE
+#define E1000_COLD_SHIFT 12
+
+/* Number of Transmit and Receive Descriptors must be a multiple of 8 */
+#define REQ_TX_DESCRIPTOR_MULTIPLE 8
+#define REQ_RX_DESCRIPTOR_MULTIPLE 8
+
+/* Default values for the transmit IPG register */
+#define DEFAULT_82542_TIPG_IPGT 10
+#define DEFAULT_82543_TIPG_IPGT_FIBER 9
+#define DEFAULT_82543_TIPG_IPGT_COPPER 8
+
+#define E1000_TIPG_IPGT_MASK 0x000003FF
+#define E1000_TIPG_IPGR1_MASK 0x000FFC00
+#define E1000_TIPG_IPGR2_MASK 0x3FF00000
+
+#define DEFAULT_82542_TIPG_IPGR1 2
+#define DEFAULT_82543_TIPG_IPGR1 8
+#define E1000_TIPG_IPGR1_SHIFT 10
+
+#define DEFAULT_82542_TIPG_IPGR2 10
+#define DEFAULT_82543_TIPG_IPGR2 6
+#define E1000_TIPG_IPGR2_SHIFT 20
+
+#define E1000_TXDMAC_DPP 0x00000001
+
+/* Adaptive IFS defines */
+#define TX_THRESHOLD_START 8
+#define TX_THRESHOLD_INCREMENT 10
+#define TX_THRESHOLD_DECREMENT 1
+#define TX_THRESHOLD_STOP 190
+#define TX_THRESHOLD_DISABLE 0
+#define TX_THRESHOLD_TIMER_MS 10000
+#define MIN_NUM_XMITS 1000
+#define IFS_MAX 80
+#define IFS_STEP 10
+#define IFS_MIN 40
+#define IFS_RATIO 4
+
+/* Extended Configuration Control and Size */
+#define E1000_EXTCNF_CTRL_PCIE_WRITE_ENABLE 0x00000001
+#define E1000_EXTCNF_CTRL_PHY_WRITE_ENABLE 0x00000002
+#define E1000_EXTCNF_CTRL_D_UD_ENABLE 0x00000004
+#define E1000_EXTCNF_CTRL_D_UD_LATENCY 0x00000008
+#define E1000_EXTCNF_CTRL_D_UD_OWNER 0x00000010
+#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
+#define E1000_EXTCNF_CTRL_MDIO_HW_OWNERSHIP 0x00000040
+#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER 0x0FFF0000
+
+#define E1000_EXTCNF_SIZE_EXT_PHY_LENGTH 0x000000FF
+#define E1000_EXTCNF_SIZE_EXT_DOCK_LENGTH 0x0000FF00
+#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH 0x00FF0000
+#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001
+#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
+
+/* PBA constants */
+#define E1000_PBA_8K 0x0008 /* 8KB, default Rx allocation */
+#define E1000_PBA_12K 0x000C /* 12KB, default Rx allocation */
+#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */
+#define E1000_PBA_20K 0x0014
+#define E1000_PBA_22K 0x0016
+#define E1000_PBA_24K 0x0018
+#define E1000_PBA_30K 0x001E
+#define E1000_PBA_32K 0x0020
+#define E1000_PBA_34K 0x0022
+#define E1000_PBA_38K 0x0026
+#define E1000_PBA_40K 0x0028
+#define E1000_PBA_48K 0x0030 /* 48KB, default RX allocation */
+
+#define E1000_PBS_16K E1000_PBA_16K
+
+/* Flow Control Constants */
+#define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
+#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
+#define FLOW_CONTROL_TYPE 0x8808
+
+/* The historical defaults for the flow control values are given below. */
+#define FC_DEFAULT_HI_THRESH (0x8000) /* 32KB */
+#define FC_DEFAULT_LO_THRESH (0x4000) /* 16KB */
+#define FC_DEFAULT_TX_TIMER (0x100) /* ~130 us */
+
+/* PCIX Config space */
+#define PCIX_COMMAND_REGISTER 0xE6
+#define PCIX_STATUS_REGISTER_LO 0xE8
+#define PCIX_STATUS_REGISTER_HI 0xEA
+
+#define PCIX_COMMAND_MMRBC_MASK 0x000C
+#define PCIX_COMMAND_MMRBC_SHIFT 0x2
+#define PCIX_STATUS_HI_MMRBC_MASK 0x0060
+#define PCIX_STATUS_HI_MMRBC_SHIFT 0x5
+#define PCIX_STATUS_HI_MMRBC_4K 0x3
+#define PCIX_STATUS_HI_MMRBC_2K 0x2
+
+/* Number of bits required to shift right the "pause" bits from the
+ * EEPROM (bits 13:12) to the "pause" (bits 8:7) field in the TXCW register.
+ */
+#define PAUSE_SHIFT 5
+
+/* Number of bits required to shift left the "SWDPIO" bits from the
+ * EEPROM (bits 8:5) to the "SWDPIO" (bits 25:22) field in the CTRL register.
+ */
+#define SWDPIO_SHIFT 17
+
+/* Number of bits required to shift left the "SWDPIO_EXT" bits from the
+ * EEPROM word F (bits 7:4) to the bits 11:8 of The Extended CTRL register.
+ */
+#define SWDPIO__EXT_SHIFT 4
+
+/* Number of bits required to shift left the "ILOS" bit from the EEPROM
+ * (bit 4) to the "ILOS" (bit 7) field in the CTRL register.
+ */
+#define ILOS_SHIFT 3
+
+#define RECEIVE_BUFFER_ALIGN_SIZE (256)
+
+/* Number of milliseconds we wait for auto-negotiation to complete */
+#define LINK_UP_TIMEOUT 500
+
+/* Number of milliseconds we wait for Eeprom auto read bit done after MAC reset */
+#define AUTO_READ_DONE_TIMEOUT 10
+/* Number of milliseconds we wait for PHY configuration done after MAC reset */
+#define PHY_CFG_TIMEOUT 100
+
+#define E1000_TX_BUFFER_SIZE ((u32)1514)
+
+/* The carrier extension symbol, as received by the NIC. */
+#define CARRIER_EXTENSION 0x0F
+
+/* TBI_ACCEPT macro definition:
+ *
+ * This macro requires:
+ * adapter = a pointer to struct e1000_hw
+ * status = the 8 bit status field of the RX descriptor with EOP set
+ * error = the 8 bit error field of the RX descriptor with EOP set
+ * length = the sum of all the length fields of the RX descriptors that
+ * make up the current frame
+ * last_byte = the last byte of the frame DMAed by the hardware
+ * max_frame_length = the maximum frame length we want to accept.
+ * min_frame_length = the minimum frame length we want to accept.
+ *
+ * This macro is a conditional that should be used in the interrupt
+ * handler's Rx processing routine when RxErrors have been detected.
+ *
+ * Typical use:
+ * ...
+ * if (TBI_ACCEPT) {
+ * accept_frame = true;
+ * e1000_tbi_adjust_stats(adapter, MacAddress);
+ * frame_length--;
+ * } else {
+ * accept_frame = false;
+ * }
+ * ...
+ */
+
+#define TBI_ACCEPT(adapter, status, errors, length, last_byte) \
+ ((adapter)->tbi_compatibility_on && \
+ (((errors) & E1000_RXD_ERR_FRAME_ERR_MASK) == E1000_RXD_ERR_CE) && \
+ ((last_byte) == CARRIER_EXTENSION) && \
+ (((status) & E1000_RXD_STAT_VP) ? \
+ (((length) > ((adapter)->min_frame_size - VLAN_TAG_SIZE)) && \
+ ((length) <= ((adapter)->max_frame_size + 1))) : \
+ (((length) > (adapter)->min_frame_size) && \
+ ((length) <= ((adapter)->max_frame_size + VLAN_TAG_SIZE + 1)))))
+
+/* Structures, enums, and macros for the PHY */
+
+/* Bit definitions for the Management Data IO (MDIO) and Management Data
+ * Clock (MDC) pins in the Device Control Register.
+ */
+#define E1000_CTRL_PHY_RESET_DIR E1000_CTRL_SWDPIO0
+#define E1000_CTRL_PHY_RESET E1000_CTRL_SWDPIN0
+#define E1000_CTRL_MDIO_DIR E1000_CTRL_SWDPIO2
+#define E1000_CTRL_MDIO E1000_CTRL_SWDPIN2
+#define E1000_CTRL_MDC_DIR E1000_CTRL_SWDPIO3
+#define E1000_CTRL_MDC E1000_CTRL_SWDPIN3
+#define E1000_CTRL_PHY_RESET_DIR4 E1000_CTRL_EXT_SDP4_DIR
+#define E1000_CTRL_PHY_RESET4 E1000_CTRL_EXT_SDP4_DATA
+
+/* PHY 1000 MII Register/Bit Definitions */
+/* PHY Registers defined by IEEE */
+#define PHY_CTRL 0x00 /* Control Register */
+#define PHY_STATUS 0x01 /* Status Register */
+#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
+#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
+#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
+#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
+#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */
+#define PHY_NEXT_PAGE_TX 0x07 /* Next Page TX */
+#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */
+#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
+#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
+#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */
+
+#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
+#define MAX_PHY_MULTI_PAGE_REG 0xF /* Registers equal on all pages */
+
+/* M88E1000 Specific Registers */
+#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
+#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
+#define M88E1000_INT_ENABLE 0x12 /* Interrupt Enable Register */
+#define M88E1000_INT_STATUS 0x13 /* Interrupt Status Register */
+#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
+#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */
+
+#define M88E1000_PHY_EXT_CTRL 0x1A /* PHY extend control register */
+#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
+#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
+#define M88E1000_PHY_VCO_REG_BIT8 0x100 /* Bits 8 & 11 are adjusted for */
+#define M88E1000_PHY_VCO_REG_BIT11 0x800 /* improved BER performance */
+
+#define IGP01E1000_IEEE_REGS_PAGE 0x0000
+#define IGP01E1000_IEEE_RESTART_AUTONEG 0x3300
+#define IGP01E1000_IEEE_FORCE_GIGA 0x0140
+
+/* IGP01E1000 Specific Registers */
+#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* PHY Specific Port Config Register */
+#define IGP01E1000_PHY_PORT_STATUS 0x11 /* PHY Specific Status Register */
+#define IGP01E1000_PHY_PORT_CTRL 0x12 /* PHY Specific Control Register */
+#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health Register */
+#define IGP01E1000_GMII_FIFO 0x14 /* GMII FIFO Register */
+#define IGP01E1000_PHY_CHANNEL_QUALITY 0x15 /* PHY Channel Quality Register */
+#define IGP02E1000_PHY_POWER_MGMT 0x19
+#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* PHY Page Select Core Register */
+
+/* IGP01E1000 AGC Registers - stores the cable length values*/
+#define IGP01E1000_PHY_AGC_A 0x1172
+#define IGP01E1000_PHY_AGC_B 0x1272
+#define IGP01E1000_PHY_AGC_C 0x1472
+#define IGP01E1000_PHY_AGC_D 0x1872
+
+/* IGP02E1000 AGC Registers for cable length values */
+#define IGP02E1000_PHY_AGC_A 0x11B1
+#define IGP02E1000_PHY_AGC_B 0x12B1
+#define IGP02E1000_PHY_AGC_C 0x14B1
+#define IGP02E1000_PHY_AGC_D 0x18B1
+
+/* IGP01E1000 DSP Reset Register */
+#define IGP01E1000_PHY_DSP_RESET 0x1F33
+#define IGP01E1000_PHY_DSP_SET 0x1F71
+#define IGP01E1000_PHY_DSP_FFE 0x1F35
+
+#define IGP01E1000_PHY_CHANNEL_NUM 4
+#define IGP02E1000_PHY_CHANNEL_NUM 4
+
+#define IGP01E1000_PHY_AGC_PARAM_A 0x1171
+#define IGP01E1000_PHY_AGC_PARAM_B 0x1271
+#define IGP01E1000_PHY_AGC_PARAM_C 0x1471
+#define IGP01E1000_PHY_AGC_PARAM_D 0x1871
+
+#define IGP01E1000_PHY_EDAC_MU_INDEX 0xC000
+#define IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS 0x8000
+
+#define IGP01E1000_PHY_ANALOG_TX_STATE 0x2890
+#define IGP01E1000_PHY_ANALOG_CLASS_A 0x2000
+#define IGP01E1000_PHY_FORCE_ANALOG_ENABLE 0x0004
+#define IGP01E1000_PHY_DSP_FFE_CM_CP 0x0069
+
+#define IGP01E1000_PHY_DSP_FFE_DEFAULT 0x002A
+/* IGP01E1000 PCS Initialization register - stores the polarity status when
+ * speed = 1000 Mbps. */
+#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4
+#define IGP01E1000_PHY_PCS_CTRL_REG 0x00B5
+
+#define IGP01E1000_ANALOG_REGS_PAGE 0x20C0
+
+/* PHY Control Register */
+#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */
+#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
+#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
+#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */
+#define MII_CR_POWER_DOWN 0x0800 /* Power down */
+#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
+#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
+#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
+
+/* PHY Status Register */
+#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */
+#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */
+#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
+#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */
+#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */
+#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
+#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */
+#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */
+#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */
+#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */
+#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */
+#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */
+#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */
+#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */
+#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */
+
+/* Autoneg Advertisement Register */
+#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */
+#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
+#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
+#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
+#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
+#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */
+#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
+#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
+#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */
+#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */
+
+/* Link Partner Ability Register (Base Page) */
+#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */
+#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */
+#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */
+#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */
+#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */
+#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */
+#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
+#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
+#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */
+#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */
+#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */
+
+/* Autoneg Expansion Register */
+#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */
+#define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */
+#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */
+#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */
+#define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP is 100TX Full Duplex Capable */
+
+/* Next Page TX Register */
+#define NPTX_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
+#define NPTX_TOGGLE 0x0800 /* Toggles between exchanges
+ * of different NP
+ */
+#define NPTX_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg
+ * 0 = cannot comply with msg
+ */
+#define NPTX_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */
+#define NPTX_NEXT_PAGE 0x8000 /* 1 = addition NP will follow
+ * 0 = sending last NP
+ */
+
+/* Link Partner Next Page Register */
+#define LP_RNPR_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
+#define LP_RNPR_TOGGLE 0x0800 /* Toggles between exchanges
+ * of different NP
+ */
+#define LP_RNPR_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg
+ * 0 = cannot comply with msg
+ */
+#define LP_RNPR_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */
+#define LP_RNPR_ACKNOWLDGE 0x4000 /* 1 = ACK / 0 = NO ACK */
+#define LP_RNPR_NEXT_PAGE 0x8000 /* 1 = addition NP will follow
+ * 0 = sending last NP
+ */
+
+/* 1000BASE-T Control Register */
+#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */
+#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
+#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
+#define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */
+ /* 0=DTE device */
+#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
+ /* 0=Configure PHY as Slave */
+#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
+ /* 0=Automatic Master/Slave config */
+#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */
+#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */
+#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */
+#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */
+#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */
+
+/* 1000BASE-T Status Register */
+#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */
+#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */
+#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */
+#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */
+#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
+#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
+#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master, 0=Slave */
+#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */
+#define SR_1000T_REMOTE_RX_STATUS_SHIFT 12
+#define SR_1000T_LOCAL_RX_STATUS_SHIFT 13
+#define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT 5
+#define FFE_IDLE_ERR_COUNT_TIMEOUT_20 20
+#define FFE_IDLE_ERR_COUNT_TIMEOUT_100 100
+
+/* Extended Status Register */
+#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */
+#define IEEE_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */
+#define IEEE_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */
+#define IEEE_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */
+
+#define PHY_TX_POLARITY_MASK 0x0100 /* register 10h bit 8 (polarity bit) */
+#define PHY_TX_NORMAL_POLARITY 0 /* register 10h bit 8 (normal polarity) */
+
+#define AUTO_POLARITY_DISABLE 0x0010 /* register 11h bit 4 */
+ /* (0=enable, 1=disable) */
+
+/* M88E1000 PHY Specific Control Register */
+#define M88E1000_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */
+#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
+#define M88E1000_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */
+#define M88E1000_PSCR_CLK125_DISABLE 0x0010 /* 1=CLK125 low,
+ * 0=CLK125 toggling
+ */
+#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
+ /* Manual MDI configuration */
+#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
+#define M88E1000_PSCR_AUTO_X_1000T 0x0040 /* 1000BASE-T: Auto crossover,
+ * 100BASE-TX/10BASE-T:
+ * MDI Mode
+ */
+#define M88E1000_PSCR_AUTO_X_MODE 0x0060 /* Auto crossover enabled
+ * all speeds.
+ */
+#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE 0x0080
+ /* 1=Enable Extended 10BASE-T distance
+ * (Lower 10BASE-T RX Threshold)
+ * 0=Normal 10BASE-T RX Threshold */
+#define M88E1000_PSCR_MII_5BIT_ENABLE 0x0100
+ /* 1=5-Bit interface in 100BASE-TX
+ * 0=MII interface in 100BASE-TX */
+#define M88E1000_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */
+#define M88E1000_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */
+#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
+
+#define M88E1000_PSCR_POLARITY_REVERSAL_SHIFT 1
+#define M88E1000_PSCR_AUTO_X_MODE_SHIFT 5
+#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT 7
+
+/* M88E1000 PHY Specific Status Register */
+#define M88E1000_PSSR_JABBER 0x0001 /* 1=Jabber */
+#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
+#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
+#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
+#define M88E1000_PSSR_CABLE_LENGTH 0x0380 /* 0=<50M;1=50-80M;2=80-110M;
+ * 3=110-140M;4=>140M */
+#define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */
+#define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */
+#define M88E1000_PSSR_PAGE_RCVD 0x1000 /* 1=Page received */
+#define M88E1000_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */
+#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
+#define M88E1000_PSSR_10MBS 0x0000 /* 00=10Mbs */
+#define M88E1000_PSSR_100MBS 0x4000 /* 01=100Mbs */
+#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
+
+#define M88E1000_PSSR_REV_POLARITY_SHIFT 1
+#define M88E1000_PSSR_DOWNSHIFT_SHIFT 5
+#define M88E1000_PSSR_MDIX_SHIFT 6
+#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
+
+/* M88E1000 Extended PHY Specific Control Register */
+#define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */
+#define M88E1000_EPSCR_DOWN_NO_IDLE 0x8000 /* 1=Lost lock detect enabled.
+ * Will assert lost lock and bring
+ * link down if idle not seen
+ * within 1ms in 1000BASE-T
+ */
+/* Number of times we will attempt to autonegotiate before downshifting if we
+ * are the master */
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_2X 0x0400
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_3X 0x0800
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_4X 0x0C00
+/* Number of times we will attempt to autonegotiate before downshifting if we
+ * are the slave */
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_DIS 0x0000
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_2X 0x0200
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_3X 0x0300
+#define M88E1000_EPSCR_TX_CLK_2_5 0x0060 /* 2.5 MHz TX_CLK */
+#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
+#define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */
+
+/* M88EC018 Rev 2 specific DownShift settings */
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_1X 0x0000
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_2X 0x0200
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_3X 0x0400
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_4X 0x0600
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_6X 0x0A00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_7X 0x0C00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_8X 0x0E00
+
+/* IGP01E1000 Specific Port Config Register - R/W */
+#define IGP01E1000_PSCFR_AUTO_MDIX_PAR_DETECT 0x0010
+#define IGP01E1000_PSCFR_PRE_EN 0x0020
+#define IGP01E1000_PSCFR_SMART_SPEED 0x0080
+#define IGP01E1000_PSCFR_DISABLE_TPLOOPBACK 0x0100
+#define IGP01E1000_PSCFR_DISABLE_JABBER 0x0400
+#define IGP01E1000_PSCFR_DISABLE_TRANSMIT 0x2000
+
+/* IGP01E1000 Specific Port Status Register - R/O */
+#define IGP01E1000_PSSR_AUTONEG_FAILED 0x0001 /* RO LH SC */
+#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002
+#define IGP01E1000_PSSR_CABLE_LENGTH 0x007C
+#define IGP01E1000_PSSR_FULL_DUPLEX 0x0200
+#define IGP01E1000_PSSR_LINK_UP 0x0400
+#define IGP01E1000_PSSR_MDIX 0x0800
+#define IGP01E1000_PSSR_SPEED_MASK 0xC000 /* speed bits mask */
+#define IGP01E1000_PSSR_SPEED_10MBPS 0x4000
+#define IGP01E1000_PSSR_SPEED_100MBPS 0x8000
+#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000
+#define IGP01E1000_PSSR_CABLE_LENGTH_SHIFT 0x0002 /* shift right 2 */
+#define IGP01E1000_PSSR_MDIX_SHIFT 0x000B /* shift right 11 */
+
+/* IGP01E1000 Specific Port Control Register - R/W */
+#define IGP01E1000_PSCR_TP_LOOPBACK 0x0010
+#define IGP01E1000_PSCR_CORRECT_NC_SCMBLR 0x0200
+#define IGP01E1000_PSCR_TEN_CRS_SELECT 0x0400
+#define IGP01E1000_PSCR_FLIP_CHIP 0x0800
+#define IGP01E1000_PSCR_AUTO_MDIX 0x1000
+#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0-MDI, 1-MDIX */
+
+/* IGP01E1000 Specific Port Link Health Register */
+#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000
+#define IGP01E1000_PLHR_GIG_SCRAMBLER_ERROR 0x4000
+#define IGP01E1000_PLHR_MASTER_FAULT 0x2000
+#define IGP01E1000_PLHR_MASTER_RESOLUTION 0x1000
+#define IGP01E1000_PLHR_GIG_REM_RCVR_NOK 0x0800 /* LH */
+#define IGP01E1000_PLHR_IDLE_ERROR_CNT_OFLOW 0x0400 /* LH */
+#define IGP01E1000_PLHR_DATA_ERR_1 0x0200 /* LH */
+#define IGP01E1000_PLHR_DATA_ERR_0 0x0100
+#define IGP01E1000_PLHR_AUTONEG_FAULT 0x0040
+#define IGP01E1000_PLHR_AUTONEG_ACTIVE 0x0010
+#define IGP01E1000_PLHR_VALID_CHANNEL_D 0x0008
+#define IGP01E1000_PLHR_VALID_CHANNEL_C 0x0004
+#define IGP01E1000_PLHR_VALID_CHANNEL_B 0x0002
+#define IGP01E1000_PLHR_VALID_CHANNEL_A 0x0001
+
+/* IGP01E1000 Channel Quality Register */
+#define IGP01E1000_MSE_CHANNEL_D 0x000F
+#define IGP01E1000_MSE_CHANNEL_C 0x00F0
+#define IGP01E1000_MSE_CHANNEL_B 0x0F00
+#define IGP01E1000_MSE_CHANNEL_A 0xF000
+
+#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */
+#define IGP02E1000_PM_D3_LPLU 0x0004 /* Enable LPLU in non-D0a modes */
+#define IGP02E1000_PM_D0_LPLU 0x0002 /* Enable LPLU in D0a mode */
+
+/* IGP01E1000 DSP reset macros */
+#define DSP_RESET_ENABLE 0x0
+#define DSP_RESET_DISABLE 0x2
+#define E1000_MAX_DSP_RESETS 10
+
+/* IGP01E1000 & IGP02E1000 AGC Registers */
+
+#define IGP01E1000_AGC_LENGTH_SHIFT 7 /* Coarse - 13:11, Fine - 10:7 */
+#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Coarse - 15:13, Fine - 12:9 */
+
+/* IGP02E1000 AGC Register Length 9-bit mask */
+#define IGP02E1000_AGC_LENGTH_MASK 0x7F
+
+/* 7 bits (3 Coarse + 4 Fine) --> 128 optional values */
+#define IGP01E1000_AGC_LENGTH_TABLE_SIZE 128
+#define IGP02E1000_AGC_LENGTH_TABLE_SIZE 113
+
+/* The precision error of the cable length is +/- 10 meters */
+#define IGP01E1000_AGC_RANGE 10
+#define IGP02E1000_AGC_RANGE 15
+
+/* IGP01E1000 PCS Initialization register */
+/* bits 3:6 in the PCS registers stores the channels polarity */
+#define IGP01E1000_PHY_POLARITY_MASK 0x0078
+
+/* IGP01E1000 GMII FIFO Register */
+#define IGP01E1000_GMII_FLEX_SPD 0x10 /* Enable flexible speed
+ * on Link-Up */
+#define IGP01E1000_GMII_SPD 0x20 /* Enable SPD */
+
+/* IGP01E1000 Analog Register */
+#define IGP01E1000_ANALOG_SPARE_FUSE_STATUS 0x20D1
+#define IGP01E1000_ANALOG_FUSE_STATUS 0x20D0
+#define IGP01E1000_ANALOG_FUSE_CONTROL 0x20DC
+#define IGP01E1000_ANALOG_FUSE_BYPASS 0x20DE
+
+#define IGP01E1000_ANALOG_FUSE_POLY_MASK 0xF000
+#define IGP01E1000_ANALOG_FUSE_FINE_MASK 0x0F80
+#define IGP01E1000_ANALOG_FUSE_COARSE_MASK 0x0070
+#define IGP01E1000_ANALOG_SPARE_FUSE_ENABLED 0x0100
+#define IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL 0x0002
+
+#define IGP01E1000_ANALOG_FUSE_COARSE_THRESH 0x0040
+#define IGP01E1000_ANALOG_FUSE_COARSE_10 0x0010
+#define IGP01E1000_ANALOG_FUSE_FINE_1 0x0080
+#define IGP01E1000_ANALOG_FUSE_FINE_10 0x0500
+
+/* Bit definitions for valid PHY IDs. */
+/* I = Integrated
+ * E = External
+ */
+#define M88_VENDOR 0x0141
+#define M88E1000_E_PHY_ID 0x01410C50
+#define M88E1000_I_PHY_ID 0x01410C30
+#define M88E1011_I_PHY_ID 0x01410C20
+#define IGP01E1000_I_PHY_ID 0x02A80380
+#define M88E1000_12_PHY_ID M88E1000_E_PHY_ID
+#define M88E1000_14_PHY_ID M88E1000_E_PHY_ID
+#define M88E1011_I_REV_4 0x04
+#define M88E1111_I_PHY_ID 0x01410CC0
+#define L1LXT971A_PHY_ID 0x001378E0
+
+/* Bits...
+ * 15-5: page
+ * 4-0: register offset
+ */
+#define PHY_PAGE_SHIFT 5
+#define PHY_REG(page, reg) \
+ (((page) << PHY_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
+
+#define IGP3_PHY_PORT_CTRL \
+ PHY_REG(769, 17) /* Port General Configuration */
+#define IGP3_PHY_RATE_ADAPT_CTRL \
+ PHY_REG(769, 25) /* Rate Adapter Control Register */
+
+#define IGP3_KMRN_FIFO_CTRL_STATS \
+ PHY_REG(770, 16) /* KMRN FIFO's control/status register */
+#define IGP3_KMRN_POWER_MNG_CTRL \
+ PHY_REG(770, 17) /* KMRN Power Management Control Register */
+#define IGP3_KMRN_INBAND_CTRL \
+ PHY_REG(770, 18) /* KMRN Inband Control Register */
+#define IGP3_KMRN_DIAG \
+ PHY_REG(770, 19) /* KMRN Diagnostic register */
+#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 /* RX PCS is not synced */
+#define IGP3_KMRN_ACK_TIMEOUT \
+ PHY_REG(770, 20) /* KMRN Acknowledge Timeouts register */
+
+#define IGP3_VR_CTRL \
+ PHY_REG(776, 18) /* Voltage regulator control register */
+#define IGP3_VR_CTRL_MODE_SHUT 0x0200 /* Enter powerdown, shutdown VRs */
+#define IGP3_VR_CTRL_MODE_MASK 0x0300 /* Shutdown VR Mask */
+
+#define IGP3_CAPABILITY \
+ PHY_REG(776, 19) /* IGP3 Capability Register */
+
+/* Capabilities for SKU Control */
+#define IGP3_CAP_INITIATE_TEAM 0x0001 /* Able to initiate a team */
+#define IGP3_CAP_WFM 0x0002 /* Support WoL and PXE */
+#define IGP3_CAP_ASF 0x0004 /* Support ASF */
+#define IGP3_CAP_LPLU 0x0008 /* Support Low Power Link Up */
+#define IGP3_CAP_DC_AUTO_SPEED 0x0010 /* Support AC/DC Auto Link Speed */
+#define IGP3_CAP_SPD 0x0020 /* Support Smart Power Down */
+#define IGP3_CAP_MULT_QUEUE 0x0040 /* Support 2 tx & 2 rx queues */
+#define IGP3_CAP_RSS 0x0080 /* Support RSS */
+#define IGP3_CAP_8021PQ 0x0100 /* Support 802.1Q & 802.1p */
+#define IGP3_CAP_AMT_CB 0x0200 /* Support active manageability and circuit breaker */
+
+#define IGP3_PPC_JORDAN_EN 0x0001
+#define IGP3_PPC_JORDAN_GIGA_SPEED 0x0002
+
+#define IGP3_KMRN_PMC_EE_IDLE_LINK_DIS 0x0001
+#define IGP3_KMRN_PMC_K0S_ENTRY_LATENCY_MASK 0x001E
+#define IGP3_KMRN_PMC_K0S_MODE1_EN_GIGA 0x0020
+#define IGP3_KMRN_PMC_K0S_MODE1_EN_100 0x0040
+
+#define IGP3E1000_PHY_MISC_CTRL 0x1B /* Misc. Ctrl register */
+#define IGP3_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Duplex Manual Set */
+
+#define IGP3_KMRN_EXT_CTRL PHY_REG(770, 18)
+#define IGP3_KMRN_EC_DIS_INBAND 0x0080
+
+#define IGP03E1000_E_PHY_ID 0x02A80390
+#define IFE_E_PHY_ID 0x02A80330 /* 10/100 PHY */
+#define IFE_PLUS_E_PHY_ID 0x02A80320
+#define IFE_C_E_PHY_ID 0x02A80310
+
+#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 /* 100BaseTx Extended Status, Control and Address */
+#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY special control register */
+#define IFE_PHY_RCV_FALSE_CARRIER 0x13 /* 100BaseTx Receive False Carrier Counter */
+#define IFE_PHY_RCV_DISCONNECT 0x14 /* 100BaseTx Receive Disconnect Counter */
+#define IFE_PHY_RCV_ERROT_FRAME 0x15 /* 100BaseTx Receive Error Frame Counter */
+#define IFE_PHY_RCV_SYMBOL_ERR 0x16 /* Receive Symbol Error Counter */
+#define IFE_PHY_PREM_EOF_ERR 0x17 /* 100BaseTx Receive Premature End Of Frame Error Counter */
+#define IFE_PHY_RCV_EOF_ERR 0x18 /* 10BaseT Receive End Of Frame Error Counter */
+#define IFE_PHY_TX_JABBER_DETECT 0x19 /* 10BaseT Transmit Jabber Detect Counter */
+#define IFE_PHY_EQUALIZER 0x1A /* PHY Equalizer Control and Status */
+#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY special control and LED configuration */
+#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control register */
+#define IFE_PHY_HWI_CONTROL 0x1D /* Hardware Integrity Control (HWI) */
+
+#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE 0x2000 /* Default 1 = Disable auto reduced power down */
+#define IFE_PESC_100BTX_POWER_DOWN 0x0400 /* Indicates the power state of 100BASE-TX */
+#define IFE_PESC_10BTX_POWER_DOWN 0x0200 /* Indicates the power state of 10BASE-T */
+#define IFE_PESC_POLARITY_REVERSED 0x0100 /* Indicates 10BASE-T polarity */
+#define IFE_PESC_PHY_ADDR_MASK 0x007C /* Bit 6:2 for sampled PHY address */
+#define IFE_PESC_SPEED 0x0002 /* Auto-negotiation speed result 1=100Mbs, 0=10Mbs */
+#define IFE_PESC_DUPLEX 0x0001 /* Auto-negotiation duplex result 1=Full, 0=Half */
+#define IFE_PESC_POLARITY_REVERSED_SHIFT 8
+
+#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 /* 1 = Dynamic Power Down disabled */
+#define IFE_PSC_FORCE_POLARITY 0x0020 /* 1=Reversed Polarity, 0=Normal */
+#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 /* 1=Auto Polarity Disabled, 0=Enabled */
+#define IFE_PSC_JABBER_FUNC_DISABLE 0x0001 /* 1=Jabber Disabled, 0=Normal Jabber Operation */
+#define IFE_PSC_FORCE_POLARITY_SHIFT 5
+#define IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT 4
+
+#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable MDI/MDI-X feature, default 0=disabled */
+#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDIX-X, 0=force MDI */
+#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */
+#define IFE_PMC_AUTO_MDIX_COMPLETE 0x0010 /* Resolution algorithm is completed */
+#define IFE_PMC_MDIX_MODE_SHIFT 6
+#define IFE_PHC_MDIX_RESET_ALL_MASK 0x0000 /* Disable auto MDI-X */
+
+#define IFE_PHC_HWI_ENABLE 0x8000 /* Enable the HWI feature */
+#define IFE_PHC_ABILITY_CHECK 0x4000 /* 1= Test Passed, 0=failed */
+#define IFE_PHC_TEST_EXEC 0x2000 /* PHY launch test pulses on the wire */
+#define IFE_PHC_HIGHZ 0x0200 /* 1 = Open Circuit */
+#define IFE_PHC_LOWZ 0x0400 /* 1 = Short Circuit */
+#define IFE_PHC_LOW_HIGH_Z_MASK 0x0600 /* Mask for indication type of problem on the line */
+#define IFE_PHC_DISTANCE_MASK 0x01FF /* Mask for distance to the cable problem, in 80cm granularity */
+#define IFE_PHC_RESET_ALL_MASK 0x0000 /* Disable HWI */
+#define IFE_PSCL_PROBE_MODE 0x0020 /* LED Probe mode */
+#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */
+#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */
+
+#define ICH_FLASH_COMMAND_TIMEOUT 5000 /* 5000 uSecs - adjusted */
+#define ICH_FLASH_ERASE_TIMEOUT 3000000 /* Up to 3 seconds - worst case */
+#define ICH_FLASH_CYCLE_REPEAT_COUNT 10 /* 10 cycles */
+#define ICH_FLASH_SEG_SIZE_256 256
+#define ICH_FLASH_SEG_SIZE_4K 4096
+#define ICH_FLASH_SEG_SIZE_64K 65536
+
+#define ICH_CYCLE_READ 0x0
+#define ICH_CYCLE_RESERVED 0x1
+#define ICH_CYCLE_WRITE 0x2
+#define ICH_CYCLE_ERASE 0x3
+
+#define ICH_FLASH_GFPREG 0x0000
+#define ICH_FLASH_HSFSTS 0x0004
+#define ICH_FLASH_HSFCTL 0x0006
+#define ICH_FLASH_FADDR 0x0008
+#define ICH_FLASH_FDATA0 0x0010
+#define ICH_FLASH_FRACC 0x0050
+#define ICH_FLASH_FREG0 0x0054
+#define ICH_FLASH_FREG1 0x0058
+#define ICH_FLASH_FREG2 0x005C
+#define ICH_FLASH_FREG3 0x0060
+#define ICH_FLASH_FPR0 0x0074
+#define ICH_FLASH_FPR1 0x0078
+#define ICH_FLASH_SSFSTS 0x0090
+#define ICH_FLASH_SSFCTL 0x0092
+#define ICH_FLASH_PREOP 0x0094
+#define ICH_FLASH_OPTYPE 0x0096
+#define ICH_FLASH_OPMENU 0x0098
+
+#define ICH_FLASH_REG_MAPSIZE 0x00A0
+#define ICH_FLASH_SECTOR_SIZE 4096
+#define ICH_GFPREG_BASE_MASK 0x1FFF
+#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
+
+/* Miscellaneous PHY bit definitions. */
+#define PHY_PREAMBLE 0xFFFFFFFF
+#define PHY_SOF 0x01
+#define PHY_OP_READ 0x02
+#define PHY_OP_WRITE 0x01
+#define PHY_TURNAROUND 0x02
+#define PHY_PREAMBLE_SIZE 32
+#define MII_CR_SPEED_1000 0x0040
+#define MII_CR_SPEED_100 0x2000
+#define MII_CR_SPEED_10 0x0000
+#define E1000_PHY_ADDRESS 0x01
+#define PHY_AUTO_NEG_TIME 45 /* 4.5 Seconds */
+#define PHY_FORCE_TIME 20 /* 2.0 Seconds */
+#define PHY_REVISION_MASK 0xFFFFFFF0
+#define DEVICE_SPEED_MASK 0x00000300 /* Device Ctrl Reg Speed Mask */
+#define REG4_SPEED_MASK 0x01E0
+#define REG9_SPEED_MASK 0x0300
+#define ADVERTISE_10_HALF 0x0001
+#define ADVERTISE_10_FULL 0x0002
+#define ADVERTISE_100_HALF 0x0004
+#define ADVERTISE_100_FULL 0x0008
+#define ADVERTISE_1000_HALF 0x0010
+#define ADVERTISE_1000_FULL 0x0020
+#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F /* Everything but 1000-Half */
+#define AUTONEG_ADVERTISE_10_100_ALL 0x000F /* All 10/100 speeds */
+#define AUTONEG_ADVERTISE_10_ALL 0x0003 /* 10Mbps Full & Half speeds */
+
+#endif /* _E1000_HW_H_ */
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_hw-2.6.32-orig.c Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,5634 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+ */
+
+/* e1000_hw.c
+ * Shared functions for accessing and configuring the MAC
+ */
+
+#include "e1000_hw.h"
+
+static s32 e1000_check_downshift(struct e1000_hw *hw);
+static s32 e1000_check_polarity(struct e1000_hw *hw,
+ e1000_rev_polarity *polarity);
+static void e1000_clear_hw_cntrs(struct e1000_hw *hw);
+static void e1000_clear_vfta(struct e1000_hw *hw);
+static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw,
+ bool link_up);
+static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw);
+static s32 e1000_detect_gig_phy(struct e1000_hw *hw);
+static s32 e1000_get_auto_rd_done(struct e1000_hw *hw);
+static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length,
+ u16 *max_length);
+static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw);
+static s32 e1000_id_led_init(struct e1000_hw *hw);
+static void e1000_init_rx_addrs(struct e1000_hw *hw);
+static s32 e1000_phy_igp_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info);
+static s32 e1000_phy_m88_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info);
+static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active);
+static s32 e1000_wait_autoneg(struct e1000_hw *hw);
+static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value);
+static s32 e1000_set_phy_type(struct e1000_hw *hw);
+static void e1000_phy_init_script(struct e1000_hw *hw);
+static s32 e1000_setup_copper_link(struct e1000_hw *hw);
+static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw);
+static s32 e1000_adjust_serdes_amplitude(struct e1000_hw *hw);
+static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw);
+static s32 e1000_config_mac_to_phy(struct e1000_hw *hw);
+static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl);
+static void e1000_lower_mdi_clk(struct e1000_hw *hw, u32 *ctrl);
+static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count);
+static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw);
+static s32 e1000_phy_reset_dsp(struct e1000_hw *hw);
+static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data);
+static s32 e1000_write_eeprom_microwire(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data);
+static s32 e1000_spi_eeprom_ready(struct e1000_hw *hw);
+static void e1000_raise_ee_clk(struct e1000_hw *hw, u32 *eecd);
+static void e1000_lower_ee_clk(struct e1000_hw *hw, u32 *eecd);
+static void e1000_shift_out_ee_bits(struct e1000_hw *hw, u16 data, u16 count);
+static s32 e1000_write_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
+ u16 phy_data);
+static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
+ u16 *phy_data);
+static u16 e1000_shift_in_ee_bits(struct e1000_hw *hw, u16 count);
+static s32 e1000_acquire_eeprom(struct e1000_hw *hw);
+static void e1000_release_eeprom(struct e1000_hw *hw);
+static void e1000_standby_eeprom(struct e1000_hw *hw);
+static s32 e1000_set_vco_speed(struct e1000_hw *hw);
+static s32 e1000_polarity_reversal_workaround(struct e1000_hw *hw);
+static s32 e1000_set_phy_mode(struct e1000_hw *hw);
+static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data);
+static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data);
+
+/* IGP cable length table */
+static const
+u16 e1000_igp_cable_length_table[IGP01E1000_AGC_LENGTH_TABLE_SIZE] = {
+ 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+ 5, 10, 10, 10, 10, 10, 10, 10, 20, 20, 20, 20, 20, 25, 25, 25,
+ 25, 25, 25, 25, 30, 30, 30, 30, 40, 40, 40, 40, 40, 40, 40, 40,
+ 40, 50, 50, 50, 50, 50, 50, 50, 60, 60, 60, 60, 60, 60, 60, 60,
+ 60, 70, 70, 70, 70, 70, 70, 80, 80, 80, 80, 80, 80, 90, 90, 90,
+ 90, 90, 90, 90, 90, 90, 100, 100, 100, 100, 100, 100, 100, 100, 100,
+ 100,
+ 100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110,
+ 110, 110,
+ 110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120,
+ 120, 120
+};
+
+static DEFINE_SPINLOCK(e1000_eeprom_lock);
+
+/**
+ * e1000_set_phy_type - Set the phy type member in the hw struct.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static s32 e1000_set_phy_type(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_set_phy_type");
+
+ if (hw->mac_type == e1000_undefined)
+ return -E1000_ERR_PHY_TYPE;
+
+ switch (hw->phy_id) {
+ case M88E1000_E_PHY_ID:
+ case M88E1000_I_PHY_ID:
+ case M88E1011_I_PHY_ID:
+ case M88E1111_I_PHY_ID:
+ hw->phy_type = e1000_phy_m88;
+ break;
+ case IGP01E1000_I_PHY_ID:
+ if (hw->mac_type == e1000_82541 ||
+ hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ hw->phy_type = e1000_phy_igp;
+ break;
+ }
+ default:
+ /* Should never have loaded on this device */
+ hw->phy_type = e1000_phy_undefined;
+ return -E1000_ERR_PHY_TYPE;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_init_script - IGP phy init script - initializes the GbE PHY
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_phy_init_script(struct e1000_hw *hw)
+{
+ u32 ret_val;
+ u16 phy_saved_data;
+
+ DEBUGFUNC("e1000_phy_init_script");
+
+ if (hw->phy_init_script) {
+ msleep(20);
+
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of this routine. */
+ ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
+
+ /* Disabled the PHY transmitter */
+ e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
+ msleep(20);
+
+ e1000_write_phy_reg(hw, 0x0000, 0x0140);
+ msleep(5);
+
+ switch (hw->mac_type) {
+ case e1000_82541:
+ case e1000_82547:
+ e1000_write_phy_reg(hw, 0x1F95, 0x0001);
+ e1000_write_phy_reg(hw, 0x1F71, 0xBD21);
+ e1000_write_phy_reg(hw, 0x1F79, 0x0018);
+ e1000_write_phy_reg(hw, 0x1F30, 0x1600);
+ e1000_write_phy_reg(hw, 0x1F31, 0x0014);
+ e1000_write_phy_reg(hw, 0x1F32, 0x161C);
+ e1000_write_phy_reg(hw, 0x1F94, 0x0003);
+ e1000_write_phy_reg(hw, 0x1F96, 0x003F);
+ e1000_write_phy_reg(hw, 0x2010, 0x0008);
+ break;
+
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ e1000_write_phy_reg(hw, 0x1F73, 0x0099);
+ break;
+ default:
+ break;
+ }
+
+ e1000_write_phy_reg(hw, 0x0000, 0x3300);
+ msleep(20);
+
+ /* Now enable the transmitter */
+ e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
+
+ if (hw->mac_type == e1000_82547) {
+ u16 fused, fine, coarse;
+
+ /* Move to analog registers page */
+ e1000_read_phy_reg(hw,
+ IGP01E1000_ANALOG_SPARE_FUSE_STATUS,
+ &fused);
+
+ if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) {
+ e1000_read_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_STATUS,
+ &fused);
+
+ fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK;
+ coarse =
+ fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK;
+
+ if (coarse >
+ IGP01E1000_ANALOG_FUSE_COARSE_THRESH) {
+ coarse -=
+ IGP01E1000_ANALOG_FUSE_COARSE_10;
+ fine -= IGP01E1000_ANALOG_FUSE_FINE_1;
+ } else if (coarse ==
+ IGP01E1000_ANALOG_FUSE_COARSE_THRESH)
+ fine -= IGP01E1000_ANALOG_FUSE_FINE_10;
+
+ fused =
+ (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) |
+ (fine & IGP01E1000_ANALOG_FUSE_FINE_MASK) |
+ (coarse &
+ IGP01E1000_ANALOG_FUSE_COARSE_MASK);
+
+ e1000_write_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_CONTROL,
+ fused);
+ e1000_write_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_BYPASS,
+ IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL);
+ }
+ }
+ }
+}
+
+/**
+ * e1000_set_mac_type - Set the mac type member in the hw struct.
+ * @hw: Struct containing variables accessed by shared code
+ */
+s32 e1000_set_mac_type(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_set_mac_type");
+
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82542:
+ switch (hw->revision_id) {
+ case E1000_82542_2_0_REV_ID:
+ hw->mac_type = e1000_82542_rev2_0;
+ break;
+ case E1000_82542_2_1_REV_ID:
+ hw->mac_type = e1000_82542_rev2_1;
+ break;
+ default:
+ /* Invalid 82542 revision ID */
+ return -E1000_ERR_MAC_TYPE;
+ }
+ break;
+ case E1000_DEV_ID_82543GC_FIBER:
+ case E1000_DEV_ID_82543GC_COPPER:
+ hw->mac_type = e1000_82543;
+ break;
+ case E1000_DEV_ID_82544EI_COPPER:
+ case E1000_DEV_ID_82544EI_FIBER:
+ case E1000_DEV_ID_82544GC_COPPER:
+ case E1000_DEV_ID_82544GC_LOM:
+ hw->mac_type = e1000_82544;
+ break;
+ case E1000_DEV_ID_82540EM:
+ case E1000_DEV_ID_82540EM_LOM:
+ case E1000_DEV_ID_82540EP:
+ case E1000_DEV_ID_82540EP_LOM:
+ case E1000_DEV_ID_82540EP_LP:
+ hw->mac_type = e1000_82540;
+ break;
+ case E1000_DEV_ID_82545EM_COPPER:
+ case E1000_DEV_ID_82545EM_FIBER:
+ hw->mac_type = e1000_82545;
+ break;
+ case E1000_DEV_ID_82545GM_COPPER:
+ case E1000_DEV_ID_82545GM_FIBER:
+ case E1000_DEV_ID_82545GM_SERDES:
+ hw->mac_type = e1000_82545_rev_3;
+ break;
+ case E1000_DEV_ID_82546EB_COPPER:
+ case E1000_DEV_ID_82546EB_FIBER:
+ case E1000_DEV_ID_82546EB_QUAD_COPPER:
+ hw->mac_type = e1000_82546;
+ break;
+ case E1000_DEV_ID_82546GB_COPPER:
+ case E1000_DEV_ID_82546GB_FIBER:
+ case E1000_DEV_ID_82546GB_SERDES:
+ case E1000_DEV_ID_82546GB_PCIE:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ hw->mac_type = e1000_82546_rev_3;
+ break;
+ case E1000_DEV_ID_82541EI:
+ case E1000_DEV_ID_82541EI_MOBILE:
+ case E1000_DEV_ID_82541ER_LOM:
+ hw->mac_type = e1000_82541;
+ break;
+ case E1000_DEV_ID_82541ER:
+ case E1000_DEV_ID_82541GI:
+ case E1000_DEV_ID_82541GI_LF:
+ case E1000_DEV_ID_82541GI_MOBILE:
+ hw->mac_type = e1000_82541_rev_2;
+ break;
+ case E1000_DEV_ID_82547EI:
+ case E1000_DEV_ID_82547EI_MOBILE:
+ hw->mac_type = e1000_82547;
+ break;
+ case E1000_DEV_ID_82547GI:
+ hw->mac_type = e1000_82547_rev_2;
+ break;
+ default:
+ /* Should never have loaded on this device */
+ return -E1000_ERR_MAC_TYPE;
+ }
+
+ switch (hw->mac_type) {
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ hw->asf_firmware_present = true;
+ break;
+ default:
+ break;
+ }
+
+ /* The 82543 chip does not count tx_carrier_errors properly in
+ * FD mode
+ */
+ if (hw->mac_type == e1000_82543)
+ hw->bad_tx_carr_stats_fd = true;
+
+ if (hw->mac_type > e1000_82544)
+ hw->has_smbus = true;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_set_media_type - Set media type and TBI compatibility.
+ * @hw: Struct containing variables accessed by shared code
+ */
+void e1000_set_media_type(struct e1000_hw *hw)
+{
+ u32 status;
+
+ DEBUGFUNC("e1000_set_media_type");
+
+ if (hw->mac_type != e1000_82543) {
+ /* tbi_compatibility is only valid on 82543 */
+ hw->tbi_compatibility_en = false;
+ }
+
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82545GM_SERDES:
+ case E1000_DEV_ID_82546GB_SERDES:
+ hw->media_type = e1000_media_type_internal_serdes;
+ break;
+ default:
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ hw->media_type = e1000_media_type_fiber;
+ break;
+ default:
+ status = er32(STATUS);
+ if (status & E1000_STATUS_TBIMODE) {
+ hw->media_type = e1000_media_type_fiber;
+ /* tbi_compatibility not valid on fiber */
+ hw->tbi_compatibility_en = false;
+ } else {
+ hw->media_type = e1000_media_type_copper;
+ }
+ break;
+ }
+ }
+}
+
+/**
+ * e1000_reset_hw: reset the hardware completely
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Reset the transmit and receive units; mask and clear all interrupts.
+ */
+s32 e1000_reset_hw(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u32 ctrl_ext;
+ u32 icr;
+ u32 manc;
+ u32 led_ctrl;
+ s32 ret_val;
+
+ DEBUGFUNC("e1000_reset_hw");
+
+ /* For 82542 (rev 2.0), disable MWI before issuing a device reset */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
+ e1000_pci_clear_mwi(hw);
+ }
+
+ /* Clear interrupt mask to stop board from generating interrupts */
+ DEBUGOUT("Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ /* Disable the Transmit and Receive units. Then delay to allow
+ * any pending transactions to complete before we hit the MAC with
+ * the global reset.
+ */
+ ew32(RCTL, 0);
+ ew32(TCTL, E1000_TCTL_PSP);
+ E1000_WRITE_FLUSH();
+
+ /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */
+ hw->tbi_compatibility_on = false;
+
+ /* Delay to allow any outstanding PCI transactions to complete before
+ * resetting the device
+ */
+ msleep(10);
+
+ ctrl = er32(CTRL);
+
+ /* Must reset the PHY before resetting the MAC */
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ ew32(CTRL, (ctrl | E1000_CTRL_PHY_RST));
+ msleep(5);
+ }
+
+ /* Issue a global reset to the MAC. This will reset the chip's
+ * transmit, receive, DMA, and link units. It will not effect
+ * the current PCI configuration. The global reset bit is self-
+ * clearing, and should clear within a microsecond.
+ */
+ DEBUGOUT("Issuing a global reset to MAC\n");
+
+ switch (hw->mac_type) {
+ case e1000_82544:
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82546:
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ /* These controllers can't ack the 64-bit write when issuing the
+ * reset, so use IO-mapping as a workaround to issue the reset */
+ E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST));
+ break;
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ /* Reset is performed on a shadow of the control register */
+ ew32(CTRL_DUP, (ctrl | E1000_CTRL_RST));
+ break;
+ default:
+ ew32(CTRL, (ctrl | E1000_CTRL_RST));
+ break;
+ }
+
+ /* After MAC reset, force reload of EEPROM to restore power-on settings to
+ * device. Later controllers reload the EEPROM automatically, so just wait
+ * for reload to complete.
+ */
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ /* Wait for reset to complete */
+ udelay(10);
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+ ew32(CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH();
+ /* Wait for EEPROM reload */
+ msleep(2);
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ /* Wait for EEPROM reload */
+ msleep(20);
+ break;
+ default:
+ /* Auto read done will delay 5ms or poll based on mac type */
+ ret_val = e1000_get_auto_rd_done(hw);
+ if (ret_val)
+ return ret_val;
+ break;
+ }
+
+ /* Disable HW ARPs on ASF enabled adapters */
+ if (hw->mac_type >= e1000_82540) {
+ manc = er32(MANC);
+ manc &= ~(E1000_MANC_ARP_EN);
+ ew32(MANC, manc);
+ }
+
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ e1000_phy_init_script(hw);
+
+ /* Configure activity LED after PHY reset */
+ led_ctrl = er32(LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ ew32(LEDCTL, led_ctrl);
+ }
+
+ /* Clear interrupt mask to stop board from generating interrupts */
+ DEBUGOUT("Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ /* Clear any pending interrupt events. */
+ icr = er32(ICR);
+
+ /* If MWI was previously enabled, reenable it. */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE)
+ e1000_pci_set_mwi(hw);
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_init_hw: Performs basic configuration of the adapter.
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Assumes that the controller has previously been reset and is in a
+ * post-reset uninitialized state. Initializes the receive address registers,
+ * multicast table, and VLAN filter table. Calls routines to setup link
+ * configuration and flow control settings. Clears all on-chip counters. Leaves
+ * the transmit and receive units disabled and uninitialized.
+ */
+s32 e1000_init_hw(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u32 i;
+ s32 ret_val;
+ u32 mta_size;
+ u32 ctrl_ext;
+
+ DEBUGFUNC("e1000_init_hw");
+
+ /* Initialize Identification LED */
+ ret_val = e1000_id_led_init(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Initializing Identification LED\n");
+ return ret_val;
+ }
+
+ /* Set the media type and TBI compatibility */
+ e1000_set_media_type(hw);
+
+ /* Disabling VLAN filtering. */
+ DEBUGOUT("Initializing the IEEE VLAN\n");
+ if (hw->mac_type < e1000_82545_rev_3)
+ ew32(VET, 0);
+ e1000_clear_vfta(hw);
+
+ /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
+ e1000_pci_clear_mwi(hw);
+ ew32(RCTL, E1000_RCTL_RST);
+ E1000_WRITE_FLUSH();
+ msleep(5);
+ }
+
+ /* Setup the receive address. This involves initializing all of the Receive
+ * Address Registers (RARs 0 - 15).
+ */
+ e1000_init_rx_addrs(hw);
+
+ /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ ew32(RCTL, 0);
+ E1000_WRITE_FLUSH();
+ msleep(1);
+ if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE)
+ e1000_pci_set_mwi(hw);
+ }
+
+ /* Zero out the Multicast HASH table */
+ DEBUGOUT("Zeroing the MTA\n");
+ mta_size = E1000_MC_TBL_SIZE;
+ for (i = 0; i < mta_size; i++) {
+ E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
+ /* use write flush to prevent Memory Write Block (MWB) from
+ * occurring when accessing our register space */
+ E1000_WRITE_FLUSH();
+ }
+
+ /* Set the PCI priority bit correctly in the CTRL register. This
+ * determines if the adapter gives priority to receives, or if it
+ * gives equal priority to transmits and receives. Valid only on
+ * 82542 and 82543 silicon.
+ */
+ if (hw->dma_fairness && hw->mac_type <= e1000_82543) {
+ ctrl = er32(CTRL);
+ ew32(CTRL, ctrl | E1000_CTRL_PRIOR);
+ }
+
+ switch (hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
+ /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
+ if (hw->bus_type == e1000_bus_type_pcix
+ && e1000_pcix_get_mmrbc(hw) > 2048)
+ e1000_pcix_set_mmrbc(hw, 2048);
+ break;
+ }
+
+ /* Call a subroutine to configure the link and setup flow control. */
+ ret_val = e1000_setup_link(hw);
+
+ /* Set the transmit descriptor write-back policy */
+ if (hw->mac_type > e1000_82544) {
+ ctrl = er32(TXDCTL);
+ ctrl =
+ (ctrl & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB;
+ ew32(TXDCTL, ctrl);
+ }
+
+ /* Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ e1000_clear_hw_cntrs(hw);
+
+ if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
+ hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
+ ctrl_ext = er32(CTRL_EXT);
+ /* Relaxed ordering must be disabled to avoid a parity
+ * error crash in a PCI slot. */
+ ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
+ ew32(CTRL_EXT, ctrl_ext);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_adjust_serdes_amplitude - Adjust SERDES output amplitude based on EEPROM setting.
+ * @hw: Struct containing variables accessed by shared code.
+ */
+static s32 e1000_adjust_serdes_amplitude(struct e1000_hw *hw)
+{
+ u16 eeprom_data;
+ s32 ret_val;
+
+ DEBUGFUNC("e1000_adjust_serdes_amplitude");
+
+ if (hw->media_type != e1000_media_type_internal_serdes)
+ return E1000_SUCCESS;
+
+ switch (hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
+ return E1000_SUCCESS;
+ }
+
+ ret_val = e1000_read_eeprom(hw, EEPROM_SERDES_AMPLITUDE, 1,
+ &eeprom_data);
+ if (ret_val) {
+ return ret_val;
+ }
+
+ if (eeprom_data != EEPROM_RESERVED_WORD) {
+ /* Adjust SERDES output amplitude only. */
+ eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL, eeprom_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_setup_link - Configures flow control and link settings.
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Determines which flow control settings to use. Calls the appropriate media-
+ * specific link configuration function. Configures the flow control settings.
+ * Assuming the adapter has a valid link partner, a valid link should be
+ * established. Assumes the hardware has previously been reset and the
+ * transmitter and receiver are not enabled.
+ */
+s32 e1000_setup_link(struct e1000_hw *hw)
+{
+ u32 ctrl_ext;
+ s32 ret_val;
+ u16 eeprom_data;
+
+ DEBUGFUNC("e1000_setup_link");
+
+ /* Read and store word 0x0F of the EEPROM. This word contains bits
+ * that determine the hardware's default PAUSE (flow control) mode,
+ * a bit that determines whether the HW defaults to enabling or
+ * disabling auto-negotiation, and the direction of the
+ * SW defined pins. If there is no SW over-ride of the flow
+ * control setting, then the variable hw->fc will
+ * be initialized based on a value in the EEPROM.
+ */
+ if (hw->fc == E1000_FC_DEFAULT) {
+ ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+ 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
+ hw->fc = E1000_FC_NONE;
+ else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
+ EEPROM_WORD0F_ASM_DIR)
+ hw->fc = E1000_FC_TX_PAUSE;
+ else
+ hw->fc = E1000_FC_FULL;
+ }
+
+ /* We want to save off the original Flow Control configuration just
+ * in case we get disconnected and then reconnected into a different
+ * hub or switch with different Flow Control capabilities.
+ */
+ if (hw->mac_type == e1000_82542_rev2_0)
+ hw->fc &= (~E1000_FC_TX_PAUSE);
+
+ if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1))
+ hw->fc &= (~E1000_FC_RX_PAUSE);
+
+ hw->original_fc = hw->fc;
+
+ DEBUGOUT1("After fix-ups FlowControl is now = %x\n", hw->fc);
+
+ /* Take the 4 bits from EEPROM word 0x0F that determine the initial
+ * polarity value for the SW controlled pins, and setup the
+ * Extended Device Control reg with that info.
+ * This is needed because one of the SW controlled pins is used for
+ * signal detection. So this should be done before e1000_setup_pcs_link()
+ * or e1000_phy_setup() is called.
+ */
+ if (hw->mac_type == e1000_82543) {
+ ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+ 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) <<
+ SWDPIO__EXT_SHIFT);
+ ew32(CTRL_EXT, ctrl_ext);
+ }
+
+ /* Call the necessary subroutine to configure the link. */
+ ret_val = (hw->media_type == e1000_media_type_copper) ?
+ e1000_setup_copper_link(hw) : e1000_setup_fiber_serdes_link(hw);
+
+ /* Initialize the flow control address, type, and PAUSE timer
+ * registers to their default values. This is done even if flow
+ * control is disabled, because it does not hurt anything to
+ * initialize these registers.
+ */
+ DEBUGOUT
+ ("Initializing the Flow Control address, type and timer regs\n");
+
+ ew32(FCT, FLOW_CONTROL_TYPE);
+ ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+ ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW);
+
+ ew32(FCTTV, hw->fc_pause_time);
+
+ /* Set the flow control receive threshold registers. Normally,
+ * these registers will be set to a default threshold that may be
+ * adjusted later by the driver's runtime code. However, if the
+ * ability to transmit pause frames in not enabled, then these
+ * registers will be set to 0.
+ */
+ if (!(hw->fc & E1000_FC_TX_PAUSE)) {
+ ew32(FCRTL, 0);
+ ew32(FCRTH, 0);
+ } else {
+ /* We need to set up the Receive Threshold high and low water marks
+ * as well as (optionally) enabling the transmission of XON frames.
+ */
+ if (hw->fc_send_xon) {
+ ew32(FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE));
+ ew32(FCRTH, hw->fc_high_water);
+ } else {
+ ew32(FCRTL, hw->fc_low_water);
+ ew32(FCRTH, hw->fc_high_water);
+ }
+ }
+ return ret_val;
+}
+
+/**
+ * e1000_setup_fiber_serdes_link - prepare fiber or serdes link
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Manipulates Physical Coding Sublayer functions in order to configure
+ * link. Assumes the hardware has been previously reset and the transmitter
+ * and receiver are not enabled.
+ */
+static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u32 status;
+ u32 txcw = 0;
+ u32 i;
+ u32 signal = 0;
+ s32 ret_val;
+
+ DEBUGFUNC("e1000_setup_fiber_serdes_link");
+
+ /* On adapters with a MAC newer than 82544, SWDP 1 will be
+ * set when the optics detect a signal. On older adapters, it will be
+ * cleared when there is a signal. This applies to fiber media only.
+ * If we're on serdes media, adjust the output amplitude to value
+ * set in the EEPROM.
+ */
+ ctrl = er32(CTRL);
+ if (hw->media_type == e1000_media_type_fiber)
+ signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
+
+ ret_val = e1000_adjust_serdes_amplitude(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Take the link out of reset */
+ ctrl &= ~(E1000_CTRL_LRST);
+
+ /* Adjust VCO speed to improve BER performance */
+ ret_val = e1000_set_vco_speed(hw);
+ if (ret_val)
+ return ret_val;
+
+ e1000_config_collision_dist(hw);
+
+ /* Check for a software override of the flow control settings, and setup
+ * the device accordingly. If auto-negotiation is enabled, then software
+ * will have to set the "PAUSE" bits to the correct value in the Tranmsit
+ * Config Word Register (TXCW) and re-start auto-negotiation. However, if
+ * auto-negotiation is disabled, then software will have to manually
+ * configure the two flow control enable bits in the CTRL register.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames, but
+ * not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but we do
+ * not support receiving pause frames).
+ * 3: Both Rx and TX flow control (symmetric) are enabled.
+ */
+ switch (hw->fc) {
+ case E1000_FC_NONE:
+ /* Flow control is completely disabled by a software over-ride. */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
+ break;
+ case E1000_FC_RX_PAUSE:
+ /* RX Flow control is enabled and TX Flow control is disabled by a
+ * software over-ride. Since there really isn't a way to advertise
+ * that we are capable of RX Pause ONLY, we will advertise that we
+ * support both symmetric and asymmetric RX PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ case E1000_FC_TX_PAUSE:
+ /* TX Flow control is enabled, and RX Flow control is disabled, by a
+ * software over-ride.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
+ break;
+ case E1000_FC_FULL:
+ /* Flow control (both RX and TX) is enabled by a software over-ride. */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ default:
+ DEBUGOUT("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ break;
+ }
+
+ /* Since auto-negotiation is enabled, take the link out of reset (the link
+ * will be in reset, because we previously reset the chip). This will
+ * restart auto-negotiation. If auto-negotiation is successful then the
+ * link-up status bit will be set and the flow control enable bits (RFCE
+ * and TFCE) will be set according to their negotiated value.
+ */
+ DEBUGOUT("Auto-negotiation enabled\n");
+
+ ew32(TXCW, txcw);
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
+
+ hw->txcw = txcw;
+ msleep(1);
+
+ /* If we have a signal (the cable is plugged in) then poll for a "Link-Up"
+ * indication in the Device Status Register. Time-out if a link isn't
+ * seen in 500 milliseconds seconds (Auto-negotiation should complete in
+ * less than 500 milliseconds even if the other end is doing it in SW).
+ * For internal serdes, we just assume a signal is present, then poll.
+ */
+ if (hw->media_type == e1000_media_type_internal_serdes ||
+ (er32(CTRL) & E1000_CTRL_SWDPIN1) == signal) {
+ DEBUGOUT("Looking for Link\n");
+ for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) {
+ msleep(10);
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU)
+ break;
+ }
+ if (i == (LINK_UP_TIMEOUT / 10)) {
+ DEBUGOUT("Never got a valid link from auto-neg!!!\n");
+ hw->autoneg_failed = 1;
+ /* AutoNeg failed to achieve a link, so we'll call
+ * e1000_check_for_link. This routine will force the link up if
+ * we detect a signal. This will allow us to communicate with
+ * non-autonegotiating link partners.
+ */
+ ret_val = e1000_check_for_link(hw);
+ if (ret_val) {
+ DEBUGOUT("Error while checking for link\n");
+ return ret_val;
+ }
+ hw->autoneg_failed = 0;
+ } else {
+ hw->autoneg_failed = 0;
+ DEBUGOUT("Valid Link Found\n");
+ }
+ } else {
+ DEBUGOUT("No Signal Detected\n");
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_copper_link_preconfig - early configuration for copper
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Make sure we have a valid PHY and change PHY mode before link setup.
+ */
+static s32 e1000_copper_link_preconfig(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_copper_link_preconfig");
+
+ ctrl = er32(CTRL);
+ /* With 82543, we need to force speed and duplex on the MAC equal to what
+ * the PHY speed and duplex configuration is. In addition, we need to
+ * perform a hardware reset on the PHY to take it out of reset.
+ */
+ if (hw->mac_type > e1000_82543) {
+ ctrl |= E1000_CTRL_SLU;
+ ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ew32(CTRL, ctrl);
+ } else {
+ ctrl |=
+ (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
+ ew32(CTRL, ctrl);
+ ret_val = e1000_phy_hw_reset(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Make sure we have a valid PHY */
+ ret_val = e1000_detect_gig_phy(hw);
+ if (ret_val) {
+ DEBUGOUT("Error, did not detect valid phy.\n");
+ return ret_val;
+ }
+ DEBUGOUT1("Phy ID = %x \n", hw->phy_id);
+
+ /* Set PHY to class A mode (if necessary) */
+ ret_val = e1000_set_phy_mode(hw);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->mac_type == e1000_82545_rev_3) ||
+ (hw->mac_type == e1000_82546_rev_3)) {
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ phy_data |= 0x00000008;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ }
+
+ if (hw->mac_type <= e1000_82543 ||
+ hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
+ hw->mac_type == e1000_82541_rev_2
+ || hw->mac_type == e1000_82547_rev_2)
+ hw->phy_reset_disable = false;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_copper_link_igp_setup - Copper link setup for e1000_phy_igp series.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static s32 e1000_copper_link_igp_setup(struct e1000_hw *hw)
+{
+ u32 led_ctrl;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_copper_link_igp_setup");
+
+ if (hw->phy_reset_disable)
+ return E1000_SUCCESS;
+
+ ret_val = e1000_phy_reset(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
+
+ /* Wait 15ms for MAC to configure PHY from eeprom settings */
+ msleep(15);
+ /* Configure activity LED after PHY reset */
+ led_ctrl = er32(LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ ew32(LEDCTL, led_ctrl);
+
+ /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */
+ if (hw->phy_type == e1000_phy_igp) {
+ /* disable lplu d3 during driver init */
+ ret_val = e1000_set_d3_lplu_state(hw, false);
+ if (ret_val) {
+ DEBUGOUT("Error Disabling LPLU D3\n");
+ return ret_val;
+ }
+ }
+
+ /* Configure mdi-mdix settings */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ hw->dsp_config_state = e1000_dsp_config_disabled;
+ /* Force MDI for earlier revs of the IGP PHY */
+ phy_data &=
+ ~(IGP01E1000_PSCR_AUTO_MDIX |
+ IGP01E1000_PSCR_FORCE_MDI_MDIX);
+ hw->mdix = 1;
+
+ } else {
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+
+ switch (hw->mdix) {
+ case 1:
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 2:
+ phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 0:
+ default:
+ phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
+ break;
+ }
+ }
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* set auto-master slave resolution settings */
+ if (hw->autoneg) {
+ e1000_ms_type phy_ms_setting = hw->master_slave;
+
+ if (hw->ffe_config_state == e1000_ffe_config_active)
+ hw->ffe_config_state = e1000_ffe_config_enabled;
+
+ if (hw->dsp_config_state == e1000_dsp_config_activated)
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+
+ /* when autonegotiation advertisement is only 1000Mbps then we
+ * should disable SmartSpeed and enable Auto MasterSlave
+ * resolution as hardware default. */
+ if (hw->autoneg_advertised == ADVERTISE_1000_FULL) {
+ /* Disable SmartSpeed */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ /* Set auto Master/Slave resolution process */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_data &= ~CR_1000T_MS_ENABLE;
+ ret_val =
+ e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* load defaults for future use */
+ hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
+ ((phy_data & CR_1000T_MS_VALUE) ?
+ e1000_ms_force_master :
+ e1000_ms_force_slave) : e1000_ms_auto;
+
+ switch (phy_ms_setting) {
+ case e1000_ms_force_master:
+ phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_force_slave:
+ phy_data |= CR_1000T_MS_ENABLE;
+ phy_data &= ~(CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_auto:
+ phy_data &= ~CR_1000T_MS_ENABLE;
+ default:
+ break;
+ }
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_copper_link_mgp_setup - Copper link setup for e1000_phy_m88 series.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static s32 e1000_copper_link_mgp_setup(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_copper_link_mgp_setup");
+
+ if (hw->phy_reset_disable)
+ return E1000_SUCCESS;
+
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+
+ /* Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+
+ switch (hw->mdix) {
+ case 1:
+ phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
+ break;
+ case 2:
+ phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
+ break;
+ case 3:
+ phy_data |= M88E1000_PSCR_AUTO_X_1000T;
+ break;
+ case 0:
+ default:
+ phy_data |= M88E1000_PSCR_AUTO_X_MODE;
+ break;
+ }
+
+ /* Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
+ if (hw->disable_polarity_correction == 1)
+ phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (hw->phy_revision < M88E1011_I_REV_4) {
+ /* Force TX_CLK in the Extended PHY Specific Control Register
+ * to 25MHz clock.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+
+ if ((hw->phy_revision == E1000_REVISION_2) &&
+ (hw->phy_id == M88E1111_I_PHY_ID)) {
+ /* Vidalia Phy, set the downshift counter to 5x */
+ phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK);
+ phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X;
+ ret_val = e1000_write_phy_reg(hw,
+ M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ } else {
+ /* Configure Master and Slave downshift values */
+ phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
+ phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
+ ret_val = e1000_write_phy_reg(hw,
+ M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+
+ /* SW Reset the PHY so all changes take effect */
+ ret_val = e1000_phy_reset(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_copper_link_autoneg - setup auto-neg
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Setup auto-negotiation and flow control advertisements,
+ * and then perform auto-negotiation.
+ */
+static s32 e1000_copper_link_autoneg(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_copper_link_autoneg");
+
+ /* Perform some bounds checking on the hw->autoneg_advertised
+ * parameter. If this variable is zero, then set it to the default.
+ */
+ hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;
+
+ /* If autoneg_advertised is zero, we assume it was not defaulted
+ * by the calling code so we set to advertise full capability.
+ */
+ if (hw->autoneg_advertised == 0)
+ hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+
+ DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
+ ret_val = e1000_phy_setup_autoneg(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Setting up Auto-Negotiation\n");
+ return ret_val;
+ }
+ DEBUGOUT("Restarting Auto-Neg\n");
+
+ /* Restart auto-negotiation by setting the Auto Neg Enable bit and
+ * the Auto Neg Restart bit in the PHY control register.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Does the user want to wait for Auto-Neg to complete here, or
+ * check at a later time (for example, callback routine).
+ */
+ if (hw->wait_autoneg_complete) {
+ ret_val = e1000_wait_autoneg(hw);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error while waiting for autoneg to complete\n");
+ return ret_val;
+ }
+ }
+
+ hw->get_link_status = true;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_copper_link_postconfig - post link setup
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Config the MAC and the PHY after link is up.
+ * 1) Set up the MAC to the current PHY speed/duplex
+ * if we are on 82543. If we
+ * are on newer silicon, we only need to configure
+ * collision distance in the Transmit Control Register.
+ * 2) Set up flow control on the MAC to that established with
+ * the link partner.
+ * 3) Config DSP to improve Gigabit link quality for some PHY revisions.
+ */
+static s32 e1000_copper_link_postconfig(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ DEBUGFUNC("e1000_copper_link_postconfig");
+
+ if (hw->mac_type >= e1000_82544) {
+ e1000_config_collision_dist(hw);
+ } else {
+ ret_val = e1000_config_mac_to_phy(hw);
+ if (ret_val) {
+ DEBUGOUT("Error configuring MAC to PHY settings\n");
+ return ret_val;
+ }
+ }
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Configuring Flow Control\n");
+ return ret_val;
+ }
+
+ /* Config DSP to improve Giga link quality */
+ if (hw->phy_type == e1000_phy_igp) {
+ ret_val = e1000_config_dsp_after_link_change(hw, true);
+ if (ret_val) {
+ DEBUGOUT("Error Configuring DSP after link up\n");
+ return ret_val;
+ }
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_setup_copper_link - phy/speed/duplex setting
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Detects which PHY is present and sets up the speed and duplex
+ */
+static s32 e1000_setup_copper_link(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 i;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_setup_copper_link");
+
+ /* Check if it is a valid PHY and set PHY mode if necessary. */
+ ret_val = e1000_copper_link_preconfig(hw);
+ if (ret_val)
+ return ret_val;
+
+ if (hw->phy_type == e1000_phy_igp) {
+ ret_val = e1000_copper_link_igp_setup(hw);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->phy_type == e1000_phy_m88) {
+ ret_val = e1000_copper_link_mgp_setup(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ if (hw->autoneg) {
+ /* Setup autoneg and flow control advertisement
+ * and perform autonegotiation */
+ ret_val = e1000_copper_link_autoneg(hw);
+ if (ret_val)
+ return ret_val;
+ } else {
+ /* PHY will be set to 10H, 10F, 100H,or 100F
+ * depending on value from forced_speed_duplex. */
+ DEBUGOUT("Forcing speed and duplex\n");
+ ret_val = e1000_phy_force_speed_duplex(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Forcing Speed and Duplex\n");
+ return ret_val;
+ }
+ }
+
+ /* Check link status. Wait up to 100 microseconds for link to become
+ * valid.
+ */
+ for (i = 0; i < 10; i++) {
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (phy_data & MII_SR_LINK_STATUS) {
+ /* Config the MAC and PHY after link is up */
+ ret_val = e1000_copper_link_postconfig(hw);
+ if (ret_val)
+ return ret_val;
+
+ DEBUGOUT("Valid link established!!!\n");
+ return E1000_SUCCESS;
+ }
+ udelay(10);
+ }
+
+ DEBUGOUT("Unable to establish link!!!\n");
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_setup_autoneg - phy settings
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Configures PHY autoneg and flow control advertisement settings
+ */
+s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 mii_autoneg_adv_reg;
+ u16 mii_1000t_ctrl_reg;
+
+ DEBUGFUNC("e1000_phy_setup_autoneg");
+
+ /* Read the MII Auto-Neg Advertisement Register (Address 4). */
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
+
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+
+ /* Need to parse both autoneg_advertised and fc and set up
+ * the appropriate PHY registers. First we will parse for
+ * autoneg_advertised software override. Since we can advertise
+ * a plethora of combinations, we need to check each bit
+ * individually.
+ */
+
+ /* First we clear all the 10/100 mb speed bits in the Auto-Neg
+ * Advertisement Register (Address 4) and the 1000 mb speed bits in
+ * the 1000Base-T Control Register (Address 9).
+ */
+ mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
+ mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
+
+ DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
+
+ /* Do we want to advertise 10 Mb Half Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_10_HALF) {
+ DEBUGOUT("Advertise 10mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+ }
+
+ /* Do we want to advertise 10 Mb Full Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_10_FULL) {
+ DEBUGOUT("Advertise 10mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+ }
+
+ /* Do we want to advertise 100 Mb Half Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_100_HALF) {
+ DEBUGOUT("Advertise 100mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
+ }
+
+ /* Do we want to advertise 100 Mb Full Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_100_FULL) {
+ DEBUGOUT("Advertise 100mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+ }
+
+ /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
+ if (hw->autoneg_advertised & ADVERTISE_1000_HALF) {
+ DEBUGOUT
+ ("Advertise 1000mb Half duplex requested, request denied!\n");
+ }
+
+ /* Do we want to advertise 1000 Mb Full Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_1000_FULL) {
+ DEBUGOUT("Advertise 1000mb Full duplex\n");
+ mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+ }
+
+ /* Check for a software override of the flow control settings, and
+ * setup the PHY advertisement registers accordingly. If
+ * auto-negotiation is enabled, then software will have to set the
+ * "PAUSE" bits to the correct value in the Auto-Negotiation
+ * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * but we do not support receiving pause frames).
+ * 3: Both Rx and TX flow control (symmetric) are enabled.
+ * other: No software override. The flow control configuration
+ * in the EEPROM is used.
+ */
+ switch (hw->fc) {
+ case E1000_FC_NONE: /* 0 */
+ /* Flow control (RX & TX) is completely disabled by a
+ * software over-ride.
+ */
+ mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case E1000_FC_RX_PAUSE: /* 1 */
+ /* RX Flow control is enabled, and TX Flow control is
+ * disabled, by a software over-ride.
+ */
+ /* Since there really isn't a way to advertise that we are
+ * capable of RX Pause ONLY, we will advertise that we
+ * support both symmetric and asymmetric RX PAUSE. Later
+ * (in e1000_config_fc_after_link_up) we will disable the
+ *hw's ability to send PAUSE frames.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case E1000_FC_TX_PAUSE: /* 2 */
+ /* TX Flow control is enabled, and RX Flow control is
+ * disabled, by a software over-ride.
+ */
+ mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
+ mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+ break;
+ case E1000_FC_FULL: /* 3 */
+ /* Flow control (both RX and TX) is enabled by a software
+ * over-ride.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ default:
+ DEBUGOUT("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
+
+ DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
+
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_force_speed_duplex - force link settings
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Force PHY speed and duplex settings to hw->forced_speed_duplex
+ */
+static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 mii_ctrl_reg;
+ u16 mii_status_reg;
+ u16 phy_data;
+ u16 i;
+
+ DEBUGFUNC("e1000_phy_force_speed_duplex");
+
+ /* Turn off Flow control if we are forcing speed and duplex. */
+ hw->fc = E1000_FC_NONE;
+
+ DEBUGOUT1("hw->fc = %d\n", hw->fc);
+
+ /* Read the Device Control Register. */
+ ctrl = er32(CTRL);
+
+ /* Set the bits to Force Speed and Duplex in the Device Ctrl Reg. */
+ ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ctrl &= ~(DEVICE_SPEED_MASK);
+
+ /* Clear the Auto Speed Detect Enable bit. */
+ ctrl &= ~E1000_CTRL_ASDE;
+
+ /* Read the MII Control Register. */
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+
+ /* We need to disable autoneg in order to force link and duplex. */
+
+ mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN;
+
+ /* Are we forcing Full or Half Duplex? */
+ if (hw->forced_speed_duplex == e1000_100_full ||
+ hw->forced_speed_duplex == e1000_10_full) {
+ /* We want to force full duplex so we SET the full duplex bits in the
+ * Device and MII Control Registers.
+ */
+ ctrl |= E1000_CTRL_FD;
+ mii_ctrl_reg |= MII_CR_FULL_DUPLEX;
+ DEBUGOUT("Full Duplex\n");
+ } else {
+ /* We want to force half duplex so we CLEAR the full duplex bits in
+ * the Device and MII Control Registers.
+ */
+ ctrl &= ~E1000_CTRL_FD;
+ mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX;
+ DEBUGOUT("Half Duplex\n");
+ }
+
+ /* Are we forcing 100Mbps??? */
+ if (hw->forced_speed_duplex == e1000_100_full ||
+ hw->forced_speed_duplex == e1000_100_half) {
+ /* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */
+ ctrl |= E1000_CTRL_SPD_100;
+ mii_ctrl_reg |= MII_CR_SPEED_100;
+ mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
+ DEBUGOUT("Forcing 100mb ");
+ } else {
+ /* Set the 10Mb bit and turn off the 1000Mb and 100Mb bits. */
+ ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+ mii_ctrl_reg |= MII_CR_SPEED_10;
+ mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
+ DEBUGOUT("Forcing 10mb ");
+ }
+
+ e1000_config_collision_dist(hw);
+
+ /* Write the configured values back to the Device Control Reg. */
+ ew32(CTRL, ctrl);
+
+ if (hw->phy_type == e1000_phy_m88) {
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ * forced whenever speed are duplex are forced.
+ */
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data);
+
+ /* Need to reset the PHY or these changes will be ignored */
+ mii_ctrl_reg |= MII_CR_RESET;
+
+ /* Disable MDI-X support for 10/100 */
+ } else {
+ /* Clear Auto-Crossover to force MDI manually. IGP requires MDI
+ * forced whenever speed or duplex are forced.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Write back the modified PHY MII control register. */
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+
+ udelay(1);
+
+ /* The wait_autoneg_complete flag may be a little misleading here.
+ * Since we are forcing speed and duplex, Auto-Neg is not enabled.
+ * But we do want to delay for a period while forcing only so we
+ * don't generate false No Link messages. So we will wait here
+ * only if the user has set wait_autoneg_complete to 1, which is
+ * the default.
+ */
+ if (hw->wait_autoneg_complete) {
+ /* We will wait for autoneg to complete. */
+ DEBUGOUT("Waiting for forced speed/duplex link.\n");
+ mii_status_reg = 0;
+
+ /* We will wait for autoneg to complete or 4.5 seconds to expire. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Auto-Neg Complete bit
+ * to be set.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (mii_status_reg & MII_SR_LINK_STATUS)
+ break;
+ msleep(100);
+ }
+ if ((i == 0) && (hw->phy_type == e1000_phy_m88)) {
+ /* We didn't get link. Reset the DSP and wait again for link. */
+ ret_val = e1000_phy_reset_dsp(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting PHY DSP\n");
+ return ret_val;
+ }
+ }
+ /* This loop will early-out if the link condition has been met. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ if (mii_status_reg & MII_SR_LINK_STATUS)
+ break;
+ msleep(100);
+ /* Read the MII Status Register and wait for Auto-Neg Complete bit
+ * to be set.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+
+ if (hw->phy_type == e1000_phy_m88) {
+ /* Because we reset the PHY above, we need to re-force TX_CLK in the
+ * Extended PHY Specific Control Register to 25MHz clock. This value
+ * defaults back to a 2.5MHz clock when the PHY is reset.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* In addition, because of the s/w reset above, we need to enable CRS on
+ * TX. This must be set for both full and half duplex operation.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543)
+ && (!hw->autoneg)
+ && (hw->forced_speed_duplex == e1000_10_full
+ || hw->forced_speed_duplex == e1000_10_half)) {
+ ret_val = e1000_polarity_reversal_workaround(hw);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_config_collision_dist - set collision distance register
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Sets the collision distance in the Transmit Control register.
+ * Link should have been established previously. Reads the speed and duplex
+ * information from the Device Status register.
+ */
+void e1000_config_collision_dist(struct e1000_hw *hw)
+{
+ u32 tctl, coll_dist;
+
+ DEBUGFUNC("e1000_config_collision_dist");
+
+ if (hw->mac_type < e1000_82543)
+ coll_dist = E1000_COLLISION_DISTANCE_82542;
+ else
+ coll_dist = E1000_COLLISION_DISTANCE;
+
+ tctl = er32(TCTL);
+
+ tctl &= ~E1000_TCTL_COLD;
+ tctl |= coll_dist << E1000_COLD_SHIFT;
+
+ ew32(TCTL, tctl);
+ E1000_WRITE_FLUSH();
+}
+
+/**
+ * e1000_config_mac_to_phy - sync phy and mac settings
+ * @hw: Struct containing variables accessed by shared code
+ * @mii_reg: data to write to the MII control register
+ *
+ * Sets MAC speed and duplex settings to reflect the those in the PHY
+ * The contents of the PHY register containing the needed information need to
+ * be passed in.
+ */
+static s32 e1000_config_mac_to_phy(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_config_mac_to_phy");
+
+ /* 82544 or newer MAC, Auto Speed Detection takes care of
+ * MAC speed/duplex configuration.*/
+ if (hw->mac_type >= e1000_82544)
+ return E1000_SUCCESS;
+
+ /* Read the Device Control Register and set the bits to Force Speed
+ * and Duplex.
+ */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS);
+
+ /* Set up duplex in the Device Control and Transmit Control
+ * registers depending on negotiated values.
+ */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (phy_data & M88E1000_PSSR_DPLX)
+ ctrl |= E1000_CTRL_FD;
+ else
+ ctrl &= ~E1000_CTRL_FD;
+
+ e1000_config_collision_dist(hw);
+
+ /* Set up speed in the Device Control register depending on
+ * negotiated values.
+ */
+ if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
+ ctrl |= E1000_CTRL_SPD_1000;
+ else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
+ ctrl |= E1000_CTRL_SPD_100;
+
+ /* Write the configured values back to the Device Control Reg. */
+ ew32(CTRL, ctrl);
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_force_mac_fc - force flow control settings
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Forces the MAC's flow control settings.
+ * Sets the TFCE and RFCE bits in the device control register to reflect
+ * the adapter settings. TFCE and RFCE need to be explicitly set by
+ * software when a Copper PHY is used because autonegotiation is managed
+ * by the PHY rather than the MAC. Software must also configure these
+ * bits when link is forced on a fiber connection.
+ */
+s32 e1000_force_mac_fc(struct e1000_hw *hw)
+{
+ u32 ctrl;
+
+ DEBUGFUNC("e1000_force_mac_fc");
+
+ /* Get the current configuration of the Device Control Register */
+ ctrl = er32(CTRL);
+
+ /* Because we didn't get link via the internal auto-negotiation
+ * mechanism (we either forced link or we got link via PHY
+ * auto-neg), we have to manually enable/disable transmit an
+ * receive flow control.
+ *
+ * The "Case" statement below enables/disable flow control
+ * according to the "hw->fc" parameter.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause
+ * frames but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * frames but we do not receive pause frames).
+ * 3: Both Rx and TX flow control (symmetric) is enabled.
+ * other: No other values should be possible at this point.
+ */
+
+ switch (hw->fc) {
+ case E1000_FC_NONE:
+ ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
+ break;
+ case E1000_FC_RX_PAUSE:
+ ctrl &= (~E1000_CTRL_TFCE);
+ ctrl |= E1000_CTRL_RFCE;
+ break;
+ case E1000_FC_TX_PAUSE:
+ ctrl &= (~E1000_CTRL_RFCE);
+ ctrl |= E1000_CTRL_TFCE;
+ break;
+ case E1000_FC_FULL:
+ ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
+ break;
+ default:
+ DEBUGOUT("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ /* Disable TX Flow Control for 82542 (rev 2.0) */
+ if (hw->mac_type == e1000_82542_rev2_0)
+ ctrl &= (~E1000_CTRL_TFCE);
+
+ ew32(CTRL, ctrl);
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_config_fc_after_link_up - configure flow control after autoneg
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Configures flow control settings after link is established
+ * Should be called immediately after a valid link has been established.
+ * Forces MAC flow control settings if link was forced. When in MII/GMII mode
+ * and autonegotiation is enabled, the MAC flow control settings will be set
+ * based on the flow control negotiated by the PHY. In TBI mode, the TFCE
+ * and RFCE bits will be automatically set to the negotiated flow control mode.
+ */
+static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 mii_status_reg;
+ u16 mii_nway_adv_reg;
+ u16 mii_nway_lp_ability_reg;
+ u16 speed;
+ u16 duplex;
+
+ DEBUGFUNC("e1000_config_fc_after_link_up");
+
+ /* Check for the case where we have fiber media and auto-neg failed
+ * so we had to force link. In this case, we need to force the
+ * configuration of the MAC to match the "fc" parameter.
+ */
+ if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed))
+ || ((hw->media_type == e1000_media_type_internal_serdes)
+ && (hw->autoneg_failed))
+ || ((hw->media_type == e1000_media_type_copper)
+ && (!hw->autoneg))) {
+ ret_val = e1000_force_mac_fc(hw);
+ if (ret_val) {
+ DEBUGOUT("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ }
+
+ /* Check for the case where we have copper media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if ((hw->media_type == e1000_media_type_copper) && hw->autoneg) {
+ /* Read the MII Status Register and check to see if AutoNeg
+ * has completed. We read this twice because this reg has
+ * some "sticky" (latched) bits.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
+ /* The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement Register
+ * (Address 4) and the Auto_Negotiation Base Page Ability
+ * Register (Address 5) to determine how flow control was
+ * negotiated.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV,
+ &mii_nway_adv_reg);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY,
+ &mii_nway_lp_ability_reg);
+ if (ret_val)
+ return ret_val;
+
+ /* Two bits in the Auto Negotiation Advertisement Register
+ * (Address 4) and two bits in the Auto Negotiation Base
+ * Page Ability Register (Address 5) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | E1000_FC_NONE
+ * 0 | 1 | 0 | DC | E1000_FC_NONE
+ * 0 | 1 | 1 | 0 | E1000_FC_NONE
+ * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE
+ * 1 | 0 | 0 | DC | E1000_FC_NONE
+ * 1 | DC | 1 | DC | E1000_FC_FULL
+ * 1 | 1 | 0 | 0 | E1000_FC_NONE
+ * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE
+ *
+ */
+ /* Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | E1000_FC_FULL
+ *
+ */
+ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+ /* Now we need to check if the user selected RX ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->original_fc == E1000_FC_FULL) {
+ hw->fc = E1000_FC_FULL;
+ DEBUGOUT("Flow Control = FULL.\n");
+ } else {
+ hw->fc = E1000_FC_RX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = RX PAUSE frames only.\n");
+ }
+ }
+ /* For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE
+ *
+ */
+ else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
+ {
+ hw->fc = E1000_FC_TX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = TX PAUSE frames only.\n");
+ }
+ /* For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE
+ *
+ */
+ else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
+ {
+ hw->fc = E1000_FC_RX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = RX PAUSE frames only.\n");
+ }
+ /* Per the IEEE spec, at this point flow control should be
+ * disabled. However, we want to consider that we could
+ * be connected to a legacy switch that doesn't advertise
+ * desired flow control, but can be forced on the link
+ * partner. So if we advertised no flow control, that is
+ * what we will resolve to. If we advertised some kind of
+ * receive capability (Rx Pause Only or Full Flow Control)
+ * and the link partner advertised none, we will configure
+ * ourselves to enable Rx Flow Control only. We can do
+ * this safely for two reasons: If the link partner really
+ * didn't want flow control enabled, and we enable Rx, no
+ * harm done since we won't be receiving any PAUSE frames
+ * anyway. If the intent on the link partner was to have
+ * flow control enabled, then by us enabling RX only, we
+ * can at least receive pause frames and process them.
+ * This is a good idea because in most cases, since we are
+ * predominantly a server NIC, more times than not we will
+ * be asked to delay transmission of packets than asking
+ * our link partner to pause transmission of frames.
+ */
+ else if ((hw->original_fc == E1000_FC_NONE ||
+ hw->original_fc == E1000_FC_TX_PAUSE) ||
+ hw->fc_strict_ieee) {
+ hw->fc = E1000_FC_NONE;
+ DEBUGOUT("Flow Control = NONE.\n");
+ } else {
+ hw->fc = E1000_FC_RX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = RX PAUSE frames only.\n");
+ }
+
+ /* Now we need to do one last check... If we auto-
+ * negotiated to HALF DUPLEX, flow control should not be
+ * enabled per IEEE 802.3 spec.
+ */
+ ret_val =
+ e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error getting link speed and duplex\n");
+ return ret_val;
+ }
+
+ if (duplex == HALF_DUPLEX)
+ hw->fc = E1000_FC_NONE;
+
+ /* Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ ret_val = e1000_force_mac_fc(hw);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ } else {
+ DEBUGOUT
+ ("Copper PHY and Auto Neg has not completed.\n");
+ }
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_check_for_serdes_link_generic - Check for link (Serdes)
+ * @hw: pointer to the HW structure
+ *
+ * Checks for link up on the hardware. If link is not up and we have
+ * a signal, then we need to force link up.
+ */
+static s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw)
+{
+ u32 rxcw;
+ u32 ctrl;
+ u32 status;
+ s32 ret_val = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_check_for_serdes_link_generic");
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+ rxcw = er32(RXCW);
+
+ /*
+ * If we don't have link (auto-negotiation failed or link partner
+ * cannot auto-negotiate), and our link partner is not trying to
+ * auto-negotiate with us (we are receiving idles or data),
+ * we need to force link up. We also need to give auto-negotiation
+ * time to complete.
+ */
+ /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */
+ if ((!(status & E1000_STATUS_LU)) && (!(rxcw & E1000_RXCW_C))) {
+ if (hw->autoneg_failed == 0) {
+ hw->autoneg_failed = 1;
+ goto out;
+ }
+ DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n");
+
+ /* Disable auto-negotiation in the TXCW register */
+ ew32(TXCW, (hw->txcw & ~E1000_TXCW_ANE));
+
+ /* Force link-up and also force full-duplex. */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* Configure Flow Control after forcing link up. */
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if (ret_val) {
+ DEBUGOUT("Error configuring flow control\n");
+ goto out;
+ }
+ } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
+ /*
+ * If we are forcing link and we are receiving /C/ ordered
+ * sets, re-enable auto-negotiation in the TXCW register
+ * and disable forced link in the Device Control register
+ * in an attempt to auto-negotiate with our link partner.
+ */
+ DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n");
+ ew32(TXCW, hw->txcw);
+ ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
+
+ hw->serdes_has_link = true;
+ } else if (!(E1000_TXCW_ANE & er32(TXCW))) {
+ /*
+ * If we force link for non-auto-negotiation switch, check
+ * link status based on MAC synchronization for internal
+ * serdes media type.
+ */
+ /* SYNCH bit and IV bit are sticky. */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_SYNCH) {
+ if (!(rxcw & E1000_RXCW_IV)) {
+ hw->serdes_has_link = true;
+ DEBUGOUT("SERDES: Link up - forced.\n");
+ }
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - force failed.\n");
+ }
+ }
+
+ if (E1000_TXCW_ANE & er32(TXCW)) {
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU) {
+ /* SYNCH bit and IV bit are sticky, so reread rxcw. */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_SYNCH) {
+ if (!(rxcw & E1000_RXCW_IV)) {
+ hw->serdes_has_link = true;
+ DEBUGOUT("SERDES: Link up - autoneg "
+ "completed successfully.\n");
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - invalid"
+ "codewords detected in autoneg.\n");
+ }
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - no sync.\n");
+ }
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - autoneg failed\n");
+ }
+ }
+
+ out:
+ return ret_val;
+}
+
+/**
+ * e1000_check_for_link
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Checks to see if the link status of the hardware has changed.
+ * Called by any function that needs to check the link status of the adapter.
+ */
+s32 e1000_check_for_link(struct e1000_hw *hw)
+{
+ u32 rxcw = 0;
+ u32 ctrl;
+ u32 status;
+ u32 rctl;
+ u32 icr;
+ u32 signal = 0;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_check_for_link");
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+
+ /* On adapters with a MAC newer than 82544, SW Definable pin 1 will be
+ * set when the optics detect a signal. On older adapters, it will be
+ * cleared when there is a signal. This applies to fiber media only.
+ */
+ if ((hw->media_type == e1000_media_type_fiber) ||
+ (hw->media_type == e1000_media_type_internal_serdes)) {
+ rxcw = er32(RXCW);
+
+ if (hw->media_type == e1000_media_type_fiber) {
+ signal =
+ (hw->mac_type >
+ e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
+ if (status & E1000_STATUS_LU)
+ hw->get_link_status = false;
+ }
+ }
+
+ /* If we have a copper PHY then we only want to go out to the PHY
+ * registers to see if Auto-Neg has completed and/or if our link
+ * status has changed. The get_link_status flag will be set if we
+ * receive a Link Status Change interrupt or we have Rx Sequence
+ * Errors.
+ */
+ if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
+ /* First we want to see if the MII Status Register reports
+ * link. If so, then we want to get the current speed/duplex
+ * of the PHY.
+ * Read the register twice since the link bit is sticky.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (phy_data & MII_SR_LINK_STATUS) {
+ hw->get_link_status = false;
+ /* Check if there was DownShift, must be checked immediately after
+ * link-up */
+ e1000_check_downshift(hw);
+
+ /* If we are on 82544 or 82543 silicon and speed/duplex
+ * are forced to 10H or 10F, then we will implement the polarity
+ * reversal workaround. We disable interrupts first, and upon
+ * returning, place the devices interrupt state to its previous
+ * value except for the link status change interrupt which will
+ * happen due to the execution of this workaround.
+ */
+
+ if ((hw->mac_type == e1000_82544
+ || hw->mac_type == e1000_82543) && (!hw->autoneg)
+ && (hw->forced_speed_duplex == e1000_10_full
+ || hw->forced_speed_duplex == e1000_10_half)) {
+ ew32(IMC, 0xffffffff);
+ ret_val =
+ e1000_polarity_reversal_workaround(hw);
+ icr = er32(ICR);
+ ew32(ICS, (icr & ~E1000_ICS_LSC));
+ ew32(IMS, IMS_ENABLE_MASK);
+ }
+
+ } else {
+ /* No link detected */
+ e1000_config_dsp_after_link_change(hw, false);
+ return 0;
+ }
+
+ /* If we are forcing speed/duplex, then we simply return since
+ * we have already determined whether we have link or not.
+ */
+ if (!hw->autoneg)
+ return -E1000_ERR_CONFIG;
+
+ /* optimize the dsp settings for the igp phy */
+ e1000_config_dsp_after_link_change(hw, true);
+
+ /* We have a M88E1000 PHY and Auto-Neg is enabled. If we
+ * have Si on board that is 82544 or newer, Auto
+ * Speed Detection takes care of MAC speed/duplex
+ * configuration. So we only need to configure Collision
+ * Distance in the MAC. Otherwise, we need to force
+ * speed/duplex on the MAC to the current PHY speed/duplex
+ * settings.
+ */
+ if (hw->mac_type >= e1000_82544)
+ e1000_config_collision_dist(hw);
+ else {
+ ret_val = e1000_config_mac_to_phy(hw);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error configuring MAC to PHY settings\n");
+ return ret_val;
+ }
+ }
+
+ /* Configure Flow Control now that Auto-Neg has completed. First, we
+ * need to restore the desired flow control settings because we may
+ * have had to re-autoneg with a different link partner.
+ */
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if (ret_val) {
+ DEBUGOUT("Error configuring flow control\n");
+ return ret_val;
+ }
+
+ /* At this point we know that we are on copper and we have
+ * auto-negotiated link. These are conditions for checking the link
+ * partner capability register. We use the link speed to determine if
+ * TBI compatibility needs to be turned on or off. If the link is not
+ * at gigabit speed, then TBI compatibility is not needed. If we are
+ * at gigabit speed, we turn on TBI compatibility.
+ */
+ if (hw->tbi_compatibility_en) {
+ u16 speed, duplex;
+ ret_val =
+ e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error getting link speed and duplex\n");
+ return ret_val;
+ }
+ if (speed != SPEED_1000) {
+ /* If link speed is not set to gigabit speed, we do not need
+ * to enable TBI compatibility.
+ */
+ if (hw->tbi_compatibility_on) {
+ /* If we previously were in the mode, turn it off. */
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_SBP;
+ ew32(RCTL, rctl);
+ hw->tbi_compatibility_on = false;
+ }
+ } else {
+ /* If TBI compatibility is was previously off, turn it on. For
+ * compatibility with a TBI link partner, we will store bad
+ * packets. Some frames have an additional byte on the end and
+ * will look like CRC errors to to the hardware.
+ */
+ if (!hw->tbi_compatibility_on) {
+ hw->tbi_compatibility_on = true;
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_SBP;
+ ew32(RCTL, rctl);
+ }
+ }
+ }
+ }
+
+ if ((hw->media_type == e1000_media_type_fiber) ||
+ (hw->media_type == e1000_media_type_internal_serdes))
+ e1000_check_for_serdes_link_generic(hw);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_get_speed_and_duplex
+ * @hw: Struct containing variables accessed by shared code
+ * @speed: Speed of the connection
+ * @duplex: Duplex setting of the connection
+
+ * Detects the current speed and duplex settings of the hardware.
+ */
+s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 *speed, u16 *duplex)
+{
+ u32 status;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_get_speed_and_duplex");
+
+ if (hw->mac_type >= e1000_82543) {
+ status = er32(STATUS);
+ if (status & E1000_STATUS_SPEED_1000) {
+ *speed = SPEED_1000;
+ DEBUGOUT("1000 Mbs, ");
+ } else if (status & E1000_STATUS_SPEED_100) {
+ *speed = SPEED_100;
+ DEBUGOUT("100 Mbs, ");
+ } else {
+ *speed = SPEED_10;
+ DEBUGOUT("10 Mbs, ");
+ }
+
+ if (status & E1000_STATUS_FD) {
+ *duplex = FULL_DUPLEX;
+ DEBUGOUT("Full Duplex\n");
+ } else {
+ *duplex = HALF_DUPLEX;
+ DEBUGOUT(" Half Duplex\n");
+ }
+ } else {
+ DEBUGOUT("1000 Mbs, Full Duplex\n");
+ *speed = SPEED_1000;
+ *duplex = FULL_DUPLEX;
+ }
+
+ /* IGP01 PHY may advertise full duplex operation after speed downgrade even
+ * if it is operating at half duplex. Here we set the duplex settings to
+ * match the duplex in the link partner's capabilities.
+ */
+ if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) {
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (!(phy_data & NWAY_ER_LP_NWAY_CAPS))
+ *duplex = HALF_DUPLEX;
+ else {
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_LP_ABILITY, &phy_data);
+ if (ret_val)
+ return ret_val;
+ if ((*speed == SPEED_100
+ && !(phy_data & NWAY_LPAR_100TX_FD_CAPS))
+ || (*speed == SPEED_10
+ && !(phy_data & NWAY_LPAR_10T_FD_CAPS)))
+ *duplex = HALF_DUPLEX;
+ }
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_wait_autoneg
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Blocks until autoneg completes or times out (~4.5 seconds)
+ */
+static s32 e1000_wait_autoneg(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 i;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_wait_autoneg");
+ DEBUGOUT("Waiting for Auto-Neg to complete.\n");
+
+ /* We will wait for autoneg to complete or 4.5 seconds to expire. */
+ for (i = PHY_AUTO_NEG_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Auto-Neg
+ * Complete bit to be set.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ if (phy_data & MII_SR_AUTONEG_COMPLETE) {
+ return E1000_SUCCESS;
+ }
+ msleep(100);
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_raise_mdi_clk - Raises the Management Data Clock
+ * @hw: Struct containing variables accessed by shared code
+ * @ctrl: Device control register's current value
+ */
+static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl)
+{
+ /* Raise the clock input to the Management Data Clock (by setting the MDC
+ * bit), and then delay 10 microseconds.
+ */
+ ew32(CTRL, (*ctrl | E1000_CTRL_MDC));
+ E1000_WRITE_FLUSH();
+ udelay(10);
+}
+
+/**
+ * e1000_lower_mdi_clk - Lowers the Management Data Clock
+ * @hw: Struct containing variables accessed by shared code
+ * @ctrl: Device control register's current value
+ */
+static void e1000_lower_mdi_clk(struct e1000_hw *hw, u32 *ctrl)
+{
+ /* Lower the clock input to the Management Data Clock (by clearing the MDC
+ * bit), and then delay 10 microseconds.
+ */
+ ew32(CTRL, (*ctrl & ~E1000_CTRL_MDC));
+ E1000_WRITE_FLUSH();
+ udelay(10);
+}
+
+/**
+ * e1000_shift_out_mdi_bits - Shifts data bits out to the PHY
+ * @hw: Struct containing variables accessed by shared code
+ * @data: Data to send out to the PHY
+ * @count: Number of bits to shift out
+ *
+ * Bits are shifted out in MSB to LSB order.
+ */
+static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count)
+{
+ u32 ctrl;
+ u32 mask;
+
+ /* We need to shift "count" number of bits out to the PHY. So, the value
+ * in the "data" parameter will be shifted out to the PHY one bit at a
+ * time. In order to do this, "data" must be broken down into bits.
+ */
+ mask = 0x01;
+ mask <<= (count - 1);
+
+ ctrl = er32(CTRL);
+
+ /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */
+ ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR);
+
+ while (mask) {
+ /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and
+ * then raising and lowering the Management Data Clock. A "0" is
+ * shifted out to the PHY by setting the MDIO bit to "0" and then
+ * raising and lowering the clock.
+ */
+ if (data & mask)
+ ctrl |= E1000_CTRL_MDIO;
+ else
+ ctrl &= ~E1000_CTRL_MDIO;
+
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
+
+ udelay(10);
+
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
+
+ mask = mask >> 1;
+ }
+}
+
+/**
+ * e1000_shift_in_mdi_bits - Shifts data bits in from the PHY
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Bits are shifted in in MSB to LSB order.
+ */
+static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u16 data = 0;
+ u8 i;
+
+ /* In order to read a register from the PHY, we need to shift in a total
+ * of 18 bits from the PHY. The first two bit (turnaround) times are used
+ * to avoid contention on the MDIO pin when a read operation is performed.
+ * These two bits are ignored by us and thrown away. Bits are "shifted in"
+ * by raising the input to the Management Data Clock (setting the MDC bit),
+ * and then reading the value of the MDIO bit.
+ */
+ ctrl = er32(CTRL);
+
+ /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */
+ ctrl &= ~E1000_CTRL_MDIO_DIR;
+ ctrl &= ~E1000_CTRL_MDIO;
+
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
+
+ /* Raise and Lower the clock before reading in the data. This accounts for
+ * the turnaround bits. The first clock occurred when we clocked out the
+ * last bit of the Register Address.
+ */
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
+
+ for (data = 0, i = 0; i < 16; i++) {
+ data = data << 1;
+ e1000_raise_mdi_clk(hw, &ctrl);
+ ctrl = er32(CTRL);
+ /* Check to see if we shifted in a "1". */
+ if (ctrl & E1000_CTRL_MDIO)
+ data |= 1;
+ e1000_lower_mdi_clk(hw, &ctrl);
+ }
+
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
+
+ return data;
+}
+
+
+/**
+ * e1000_read_phy_reg - read a phy register
+ * @hw: Struct containing variables accessed by shared code
+ * @reg_addr: address of the PHY register to read
+ *
+ * Reads the value from a PHY register, if the value is on a specific non zero
+ * page, sets the page first.
+ */
+s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 *phy_data)
+{
+ u32 ret_val;
+
+ DEBUGFUNC("e1000_read_phy_reg");
+
+ if ((hw->phy_type == e1000_phy_igp) &&
+ (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+ ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (u16) reg_addr);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
+ phy_data);
+
+ return ret_val;
+}
+
+static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
+ u16 *phy_data)
+{
+ u32 i;
+ u32 mdic = 0;
+ const u32 phy_addr = 1;
+
+ DEBUGFUNC("e1000_read_phy_reg_ex");
+
+ if (reg_addr > MAX_PHY_REG_ADDRESS) {
+ DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
+ return -E1000_ERR_PARAM;
+ }
+
+ if (hw->mac_type > e1000_82543) {
+ /* Set up Op-code, Phy Address, and register address in the MDI
+ * Control register. The MAC will take care of interfacing with the
+ * PHY to retrieve the desired data.
+ */
+ mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
+ (phy_addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_READ));
+
+ ew32(MDIC, mdic);
+
+ /* Poll the ready bit to see if the MDI read completed */
+ for (i = 0; i < 64; i++) {
+ udelay(50);
+ mdic = er32(MDIC);
+ if (mdic & E1000_MDIC_READY)
+ break;
+ }
+ if (!(mdic & E1000_MDIC_READY)) {
+ DEBUGOUT("MDI Read did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ if (mdic & E1000_MDIC_ERROR) {
+ DEBUGOUT("MDI Error\n");
+ return -E1000_ERR_PHY;
+ }
+ *phy_data = (u16) mdic;
+ } else {
+ /* We must first send a preamble through the MDIO pin to signal the
+ * beginning of an MII instruction. This is done by sending 32
+ * consecutive "1" bits.
+ */
+ e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
+
+ /* Now combine the next few fields that are required for a read
+ * operation. We use this method instead of calling the
+ * e1000_shift_out_mdi_bits routine five different times. The format of
+ * a MII read instruction consists of a shift out of 14 bits and is
+ * defined as follows:
+ * <Preamble><SOF><Op Code><Phy Addr><Reg Addr>
+ * followed by a shift in of 18 bits. This first two bits shifted in
+ * are TurnAround bits used to avoid contention on the MDIO pin when a
+ * READ operation is performed. These two bits are thrown away
+ * followed by a shift in of 16 bits which contains the desired data.
+ */
+ mdic = ((reg_addr) | (phy_addr << 5) |
+ (PHY_OP_READ << 10) | (PHY_SOF << 12));
+
+ e1000_shift_out_mdi_bits(hw, mdic, 14);
+
+ /* Now that we've shifted out the read command to the MII, we need to
+ * "shift in" the 16-bit value (18 total bits) of the requested PHY
+ * register address.
+ */
+ *phy_data = e1000_shift_in_mdi_bits(hw);
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_write_phy_reg - write a phy register
+ *
+ * @hw: Struct containing variables accessed by shared code
+ * @reg_addr: address of the PHY register to write
+ * @data: data to write to the PHY
+
+ * Writes a value to a PHY register
+ */
+s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 phy_data)
+{
+ u32 ret_val;
+
+ DEBUGFUNC("e1000_write_phy_reg");
+
+ if ((hw->phy_type == e1000_phy_igp) &&
+ (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+ ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (u16) reg_addr);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
+ phy_data);
+
+ return ret_val;
+}
+
+static s32 e1000_write_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
+ u16 phy_data)
+{
+ u32 i;
+ u32 mdic = 0;
+ const u32 phy_addr = 1;
+
+ DEBUGFUNC("e1000_write_phy_reg_ex");
+
+ if (reg_addr > MAX_PHY_REG_ADDRESS) {
+ DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
+ return -E1000_ERR_PARAM;
+ }
+
+ if (hw->mac_type > e1000_82543) {
+ /* Set up Op-code, Phy Address, register address, and data intended
+ * for the PHY register in the MDI Control register. The MAC will take
+ * care of interfacing with the PHY to send the desired data.
+ */
+ mdic = (((u32) phy_data) |
+ (reg_addr << E1000_MDIC_REG_SHIFT) |
+ (phy_addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_WRITE));
+
+ ew32(MDIC, mdic);
+
+ /* Poll the ready bit to see if the MDI read completed */
+ for (i = 0; i < 641; i++) {
+ udelay(5);
+ mdic = er32(MDIC);
+ if (mdic & E1000_MDIC_READY)
+ break;
+ }
+ if (!(mdic & E1000_MDIC_READY)) {
+ DEBUGOUT("MDI Write did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ } else {
+ /* We'll need to use the SW defined pins to shift the write command
+ * out to the PHY. We first send a preamble to the PHY to signal the
+ * beginning of the MII instruction. This is done by sending 32
+ * consecutive "1" bits.
+ */
+ e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
+
+ /* Now combine the remaining required fields that will indicate a
+ * write operation. We use this method instead of calling the
+ * e1000_shift_out_mdi_bits routine for each field in the command. The
+ * format of a MII write instruction is as follows:
+ * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>.
+ */
+ mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) |
+ (PHY_OP_WRITE << 12) | (PHY_SOF << 14));
+ mdic <<= 16;
+ mdic |= (u32) phy_data;
+
+ e1000_shift_out_mdi_bits(hw, mdic, 32);
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_hw_reset - reset the phy, hardware style
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Returns the PHY to the power-on reset state
+ */
+s32 e1000_phy_hw_reset(struct e1000_hw *hw)
+{
+ u32 ctrl, ctrl_ext;
+ u32 led_ctrl;
+ s32 ret_val;
+
+ DEBUGFUNC("e1000_phy_hw_reset");
+
+ DEBUGOUT("Resetting Phy...\n");
+
+ if (hw->mac_type > e1000_82543) {
+ /* Read the device control register and assert the E1000_CTRL_PHY_RST
+ * bit. Then, take it out of reset.
+ * For e1000 hardware, we delay for 10ms between the assert
+ * and deassert.
+ */
+ ctrl = er32(CTRL);
+ ew32(CTRL, ctrl | E1000_CTRL_PHY_RST);
+ E1000_WRITE_FLUSH();
+
+ msleep(10);
+
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
+
+ } else {
+ /* Read the Extended Device Control Register, assert the PHY_RESET_DIR
+ * bit to put the PHY into reset. Then, take it out of reset.
+ */
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR;
+ ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA;
+ ew32(CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH();
+ msleep(10);
+ ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA;
+ ew32(CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH();
+ }
+ udelay(150);
+
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ /* Configure activity LED after PHY reset */
+ led_ctrl = er32(LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ ew32(LEDCTL, led_ctrl);
+ }
+
+ /* Wait for FW to finish PHY configuration. */
+ ret_val = e1000_get_phy_cfg_done(hw);
+ if (ret_val != E1000_SUCCESS)
+ return ret_val;
+
+ return ret_val;
+}
+
+/**
+ * e1000_phy_reset - reset the phy to commit settings
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Resets the PHY
+ * Sets bit 15 of the MII Control register
+ */
+s32 e1000_phy_reset(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_phy_reset");
+
+ switch (hw->phy_type) {
+ case e1000_phy_igp:
+ ret_val = e1000_phy_hw_reset(hw);
+ if (ret_val)
+ return ret_val;
+ break;
+ default:
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= MII_CR_RESET;
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ udelay(1);
+ break;
+ }
+
+ if (hw->phy_type == e1000_phy_igp)
+ e1000_phy_init_script(hw);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_detect_gig_phy - check the phy type
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Probes the expected PHY address for known PHY IDs
+ */
+static s32 e1000_detect_gig_phy(struct e1000_hw *hw)
+{
+ s32 phy_init_status, ret_val;
+ u16 phy_id_high, phy_id_low;
+ bool match = false;
+
+ DEBUGFUNC("e1000_detect_gig_phy");
+
+ if (hw->phy_id != 0)
+ return E1000_SUCCESS;
+
+ /* Read the PHY ID Registers to identify which PHY is onboard. */
+ ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy_id = (u32) (phy_id_high << 16);
+ udelay(20);
+ ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy_id |= (u32) (phy_id_low & PHY_REVISION_MASK);
+ hw->phy_revision = (u32) phy_id_low & ~PHY_REVISION_MASK;
+
+ switch (hw->mac_type) {
+ case e1000_82543:
+ if (hw->phy_id == M88E1000_E_PHY_ID)
+ match = true;
+ break;
+ case e1000_82544:
+ if (hw->phy_id == M88E1000_I_PHY_ID)
+ match = true;
+ break;
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ if (hw->phy_id == M88E1011_I_PHY_ID)
+ match = true;
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ if (hw->phy_id == IGP01E1000_I_PHY_ID)
+ match = true;
+ break;
+ default:
+ DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
+ return -E1000_ERR_CONFIG;
+ }
+ phy_init_status = e1000_set_phy_type(hw);
+
+ if ((match) && (phy_init_status == E1000_SUCCESS)) {
+ DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id);
+ return E1000_SUCCESS;
+ }
+ DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id);
+ return -E1000_ERR_PHY;
+}
+
+/**
+ * e1000_phy_reset_dsp - reset DSP
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Resets the PHY's DSP
+ */
+static s32 e1000_phy_reset_dsp(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ DEBUGFUNC("e1000_phy_reset_dsp");
+
+ do {
+ ret_val = e1000_write_phy_reg(hw, 29, 0x001d);
+ if (ret_val)
+ break;
+ ret_val = e1000_write_phy_reg(hw, 30, 0x00c1);
+ if (ret_val)
+ break;
+ ret_val = e1000_write_phy_reg(hw, 30, 0x0000);
+ if (ret_val)
+ break;
+ ret_val = E1000_SUCCESS;
+ } while (0);
+
+ return ret_val;
+}
+
+/**
+ * e1000_phy_igp_get_info - get igp specific registers
+ * @hw: Struct containing variables accessed by shared code
+ * @phy_info: PHY information structure
+ *
+ * Get PHY information from various PHY registers for igp PHY only.
+ */
+static s32 e1000_phy_igp_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info)
+{
+ s32 ret_val;
+ u16 phy_data, min_length, max_length, average;
+ e1000_rev_polarity polarity;
+
+ DEBUGFUNC("e1000_phy_igp_get_info");
+
+ /* The downshift status is checked only once, after link is established,
+ * and it stored in the hw->speed_downgraded parameter. */
+ phy_info->downshift = (e1000_downshift) hw->speed_downgraded;
+
+ /* IGP01E1000 does not need to support it. */
+ phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal;
+
+ /* IGP01E1000 always correct polarity reversal */
+ phy_info->polarity_correction = e1000_polarity_reversal_enabled;
+
+ /* Check polarity status */
+ ret_val = e1000_check_polarity(hw, &polarity);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->cable_polarity = polarity;
+
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->mdix_mode =
+ (e1000_auto_x_mode) ((phy_data & IGP01E1000_PSSR_MDIX) >>
+ IGP01E1000_PSSR_MDIX_SHIFT);
+
+ if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+ /* Local/Remote Receiver Information are only valid at 1000 Mbps */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >>
+ SR_1000T_LOCAL_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+ phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >>
+ SR_1000T_REMOTE_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+
+ /* Get cable length */
+ ret_val = e1000_get_cable_length(hw, &min_length, &max_length);
+ if (ret_val)
+ return ret_val;
+
+ /* Translate to old method */
+ average = (max_length + min_length) / 2;
+
+ if (average <= e1000_igp_cable_length_50)
+ phy_info->cable_length = e1000_cable_length_50;
+ else if (average <= e1000_igp_cable_length_80)
+ phy_info->cable_length = e1000_cable_length_50_80;
+ else if (average <= e1000_igp_cable_length_110)
+ phy_info->cable_length = e1000_cable_length_80_110;
+ else if (average <= e1000_igp_cable_length_140)
+ phy_info->cable_length = e1000_cable_length_110_140;
+ else
+ phy_info->cable_length = e1000_cable_length_140;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_m88_get_info - get m88 specific registers
+ * @hw: Struct containing variables accessed by shared code
+ * @phy_info: PHY information structure
+ *
+ * Get PHY information from various PHY registers for m88 PHY only.
+ */
+static s32 e1000_phy_m88_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info)
+{
+ s32 ret_val;
+ u16 phy_data;
+ e1000_rev_polarity polarity;
+
+ DEBUGFUNC("e1000_phy_m88_get_info");
+
+ /* The downshift status is checked only once, after link is established,
+ * and it stored in the hw->speed_downgraded parameter. */
+ phy_info->downshift = (e1000_downshift) hw->speed_downgraded;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->extended_10bt_distance =
+ ((phy_data & M88E1000_PSCR_10BT_EXT_DIST_ENABLE) >>
+ M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT) ?
+ e1000_10bt_ext_dist_enable_lower :
+ e1000_10bt_ext_dist_enable_normal;
+
+ phy_info->polarity_correction =
+ ((phy_data & M88E1000_PSCR_POLARITY_REVERSAL) >>
+ M88E1000_PSCR_POLARITY_REVERSAL_SHIFT) ?
+ e1000_polarity_reversal_disabled : e1000_polarity_reversal_enabled;
+
+ /* Check polarity status */
+ ret_val = e1000_check_polarity(hw, &polarity);
+ if (ret_val)
+ return ret_val;
+ phy_info->cable_polarity = polarity;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->mdix_mode =
+ (e1000_auto_x_mode) ((phy_data & M88E1000_PSSR_MDIX) >>
+ M88E1000_PSSR_MDIX_SHIFT);
+
+ if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) {
+ /* Cable Length Estimation and Local/Remote Receiver Information
+ * are only valid at 1000 Mbps.
+ */
+ phy_info->cable_length =
+ (e1000_cable_length) ((phy_data &
+ M88E1000_PSSR_CABLE_LENGTH) >>
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT);
+
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >>
+ SR_1000T_LOCAL_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+ phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >>
+ SR_1000T_REMOTE_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_phy_get_info - request phy info
+ * @hw: Struct containing variables accessed by shared code
+ * @phy_info: PHY information structure
+ *
+ * Get PHY information from various PHY registers
+ */
+s32 e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_phy_get_info");
+
+ phy_info->cable_length = e1000_cable_length_undefined;
+ phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_undefined;
+ phy_info->cable_polarity = e1000_rev_polarity_undefined;
+ phy_info->downshift = e1000_downshift_undefined;
+ phy_info->polarity_correction = e1000_polarity_reversal_undefined;
+ phy_info->mdix_mode = e1000_auto_x_mode_undefined;
+ phy_info->local_rx = e1000_1000t_rx_status_undefined;
+ phy_info->remote_rx = e1000_1000t_rx_status_undefined;
+
+ if (hw->media_type != e1000_media_type_copper) {
+ DEBUGOUT("PHY info is only valid for copper media\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) {
+ DEBUGOUT("PHY info is only valid if link is up\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ if (hw->phy_type == e1000_phy_igp)
+ return e1000_phy_igp_get_info(hw, phy_info);
+ else
+ return e1000_phy_m88_get_info(hw, phy_info);
+}
+
+s32 e1000_validate_mdi_setting(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_validate_mdi_settings");
+
+ if (!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) {
+ DEBUGOUT("Invalid MDI setting detected\n");
+ hw->mdix = 1;
+ return -E1000_ERR_CONFIG;
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_init_eeprom_params - initialize sw eeprom vars
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Sets up eeprom variables in the hw struct. Must be called after mac_type
+ * is configured.
+ */
+s32 e1000_init_eeprom_params(struct e1000_hw *hw)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd = er32(EECD);
+ s32 ret_val = E1000_SUCCESS;
+ u16 eeprom_size;
+
+ DEBUGFUNC("e1000_init_eeprom_params");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->word_size = 64;
+ eeprom->opcode_bits = 3;
+ eeprom->address_bits = 6;
+ eeprom->delay_usec = 50;
+ break;
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->opcode_bits = 3;
+ eeprom->delay_usec = 50;
+ if (eecd & E1000_EECD_SIZE) {
+ eeprom->word_size = 256;
+ eeprom->address_bits = 8;
+ } else {
+ eeprom->word_size = 64;
+ eeprom->address_bits = 6;
+ }
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ if (eecd & E1000_EECD_TYPE) {
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ } else {
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->opcode_bits = 3;
+ eeprom->delay_usec = 50;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->word_size = 256;
+ eeprom->address_bits = 8;
+ } else {
+ eeprom->word_size = 64;
+ eeprom->address_bits = 6;
+ }
+ }
+ break;
+ default:
+ break;
+ }
+
+ if (eeprom->type == e1000_eeprom_spi) {
+ /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to
+ * 32KB (incremented by powers of 2).
+ */
+ /* Set to default value for initial eeprom read. */
+ eeprom->word_size = 64;
+ ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size);
+ if (ret_val)
+ return ret_val;
+ eeprom_size =
+ (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT;
+ /* 256B eeprom size was not supported in earlier hardware, so we
+ * bump eeprom_size up one to ensure that "1" (which maps to 256B)
+ * is never the result used in the shifting logic below. */
+ if (eeprom_size)
+ eeprom_size++;
+
+ eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT);
+ }
+ return ret_val;
+}
+
+/**
+ * e1000_raise_ee_clk - Raises the EEPROM's clock input.
+ * @hw: Struct containing variables accessed by shared code
+ * @eecd: EECD's current value
+ */
+static void e1000_raise_ee_clk(struct e1000_hw *hw, u32 *eecd)
+{
+ /* Raise the clock input to the EEPROM (by setting the SK bit), and then
+ * wait <delay> microseconds.
+ */
+ *eecd = *eecd | E1000_EECD_SK;
+ ew32(EECD, *eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
+}
+
+/**
+ * e1000_lower_ee_clk - Lowers the EEPROM's clock input.
+ * @hw: Struct containing variables accessed by shared code
+ * @eecd: EECD's current value
+ */
+static void e1000_lower_ee_clk(struct e1000_hw *hw, u32 *eecd)
+{
+ /* Lower the clock input to the EEPROM (by clearing the SK bit), and then
+ * wait 50 microseconds.
+ */
+ *eecd = *eecd & ~E1000_EECD_SK;
+ ew32(EECD, *eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
+}
+
+/**
+ * e1000_shift_out_ee_bits - Shift data bits out to the EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @data: data to send to the EEPROM
+ * @count: number of bits to shift out
+ */
+static void e1000_shift_out_ee_bits(struct e1000_hw *hw, u16 data, u16 count)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd;
+ u32 mask;
+
+ /* We need to shift "count" bits out to the EEPROM. So, value in the
+ * "data" parameter will be shifted out to the EEPROM one bit at a time.
+ * In order to do this, "data" must be broken down into bits.
+ */
+ mask = 0x01 << (count - 1);
+ eecd = er32(EECD);
+ if (eeprom->type == e1000_eeprom_microwire) {
+ eecd &= ~E1000_EECD_DO;
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ eecd |= E1000_EECD_DO;
+ }
+ do {
+ /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1",
+ * and then raising and then lowering the clock (the SK bit controls
+ * the clock input to the EEPROM). A "0" is shifted out to the EEPROM
+ * by setting "DI" to "0" and then raising and then lowering the clock.
+ */
+ eecd &= ~E1000_EECD_DI;
+
+ if (data & mask)
+ eecd |= E1000_EECD_DI;
+
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+
+ udelay(eeprom->delay_usec);
+
+ e1000_raise_ee_clk(hw, &eecd);
+ e1000_lower_ee_clk(hw, &eecd);
+
+ mask = mask >> 1;
+
+ } while (mask);
+
+ /* We leave the "DI" bit set to "0" when we leave this routine. */
+ eecd &= ~E1000_EECD_DI;
+ ew32(EECD, eecd);
+}
+
+/**
+ * e1000_shift_in_ee_bits - Shift data bits in from the EEPROM
+ * @hw: Struct containing variables accessed by shared code
+ * @count: number of bits to shift in
+ */
+static u16 e1000_shift_in_ee_bits(struct e1000_hw *hw, u16 count)
+{
+ u32 eecd;
+ u32 i;
+ u16 data;
+
+ /* In order to read a register from the EEPROM, we need to shift 'count'
+ * bits in from the EEPROM. Bits are "shifted in" by raising the clock
+ * input to the EEPROM (setting the SK bit), and then reading the value of
+ * the "DO" bit. During this "shifting in" process the "DI" bit should
+ * always be clear.
+ */
+
+ eecd = er32(EECD);
+
+ eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
+ data = 0;
+
+ for (i = 0; i < count; i++) {
+ data = data << 1;
+ e1000_raise_ee_clk(hw, &eecd);
+
+ eecd = er32(EECD);
+
+ eecd &= ~(E1000_EECD_DI);
+ if (eecd & E1000_EECD_DO)
+ data |= 1;
+
+ e1000_lower_ee_clk(hw, &eecd);
+ }
+
+ return data;
+}
+
+/**
+ * e1000_acquire_eeprom - Prepares EEPROM for access
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This
+ * function should be called before issuing a command to the EEPROM.
+ */
+static s32 e1000_acquire_eeprom(struct e1000_hw *hw)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd, i = 0;
+
+ DEBUGFUNC("e1000_acquire_eeprom");
+
+ eecd = er32(EECD);
+
+ /* Request EEPROM Access */
+ if (hw->mac_type > e1000_82544) {
+ eecd |= E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ eecd = er32(EECD);
+ while ((!(eecd & E1000_EECD_GNT)) &&
+ (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
+ i++;
+ udelay(5);
+ eecd = er32(EECD);
+ }
+ if (!(eecd & E1000_EECD_GNT)) {
+ eecd &= ~E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ DEBUGOUT("Could not acquire EEPROM grant\n");
+ return -E1000_ERR_EEPROM;
+ }
+ }
+
+ /* Setup EEPROM for Read/Write */
+
+ if (eeprom->type == e1000_eeprom_microwire) {
+ /* Clear SK and DI */
+ eecd &= ~(E1000_EECD_DI | E1000_EECD_SK);
+ ew32(EECD, eecd);
+
+ /* Set CS */
+ eecd |= E1000_EECD_CS;
+ ew32(EECD, eecd);
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ /* Clear SK and CS */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ ew32(EECD, eecd);
+ udelay(1);
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_standby_eeprom - Returns EEPROM to a "standby" state
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_standby_eeprom(struct e1000_hw *hw)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd;
+
+ eecd = er32(EECD);
+
+ if (eeprom->type == e1000_eeprom_microwire) {
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+
+ /* Clock high */
+ eecd |= E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+
+ /* Select EEPROM */
+ eecd |= E1000_EECD_CS;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+
+ /* Clock low */
+ eecd &= ~E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ /* Toggle CS to flush commands */
+ eecd |= E1000_EECD_CS;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+ eecd &= ~E1000_EECD_CS;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+ }
+}
+
+/**
+ * e1000_release_eeprom - drop chip select
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Terminates a command by inverting the EEPROM's chip select pin
+ */
+static void e1000_release_eeprom(struct e1000_hw *hw)
+{
+ u32 eecd;
+
+ DEBUGFUNC("e1000_release_eeprom");
+
+ eecd = er32(EECD);
+
+ if (hw->eeprom.type == e1000_eeprom_spi) {
+ eecd |= E1000_EECD_CS; /* Pull CS high */
+ eecd &= ~E1000_EECD_SK; /* Lower SCK */
+
+ ew32(EECD, eecd);
+
+ udelay(hw->eeprom.delay_usec);
+ } else if (hw->eeprom.type == e1000_eeprom_microwire) {
+ /* cleanup eeprom */
+
+ /* CS on Microwire is active-high */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);
+
+ ew32(EECD, eecd);
+
+ /* Rising edge of clock */
+ eecd |= E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
+
+ /* Falling edge of clock */
+ eecd &= ~E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
+ }
+
+ /* Stop requesting EEPROM access */
+ if (hw->mac_type > e1000_82544) {
+ eecd &= ~E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ }
+}
+
+/**
+ * e1000_spi_eeprom_ready - Reads a 16 bit word from the EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static s32 e1000_spi_eeprom_ready(struct e1000_hw *hw)
+{
+ u16 retry_count = 0;
+ u8 spi_stat_reg;
+
+ DEBUGFUNC("e1000_spi_eeprom_ready");
+
+ /* Read "Status Register" repeatedly until the LSB is cleared. The
+ * EEPROM will signal that the command has been completed by clearing
+ * bit 0 of the internal status register. If it's not cleared within
+ * 5 milliseconds, then error out.
+ */
+ retry_count = 0;
+ do {
+ e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI,
+ hw->eeprom.opcode_bits);
+ spi_stat_reg = (u8) e1000_shift_in_ee_bits(hw, 8);
+ if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI))
+ break;
+
+ udelay(5);
+ retry_count += 5;
+
+ e1000_standby_eeprom(hw);
+ } while (retry_count < EEPROM_MAX_RETRY_SPI);
+
+ /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and
+ * only 0-5mSec on 5V devices)
+ */
+ if (retry_count >= EEPROM_MAX_RETRY_SPI) {
+ DEBUGOUT("SPI EEPROM Status error\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_read_eeprom - Reads a 16 bit word from the EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset of word in the EEPROM to read
+ * @data: word read from the EEPROM
+ * @words: number of words to read
+ */
+s32 e1000_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ s32 ret;
+ spin_lock(&e1000_eeprom_lock);
+ ret = e1000_do_read_eeprom(hw, offset, words, data);
+ spin_unlock(&e1000_eeprom_lock);
+ return ret;
+}
+
+static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 i = 0;
+
+ DEBUGFUNC("e1000_read_eeprom");
+
+ /* If eeprom is not yet detected, do so now */
+ if (eeprom->word_size == 0)
+ e1000_init_eeprom_params(hw);
+
+ /* A check for invalid values: offset too large, too many words, and not
+ * enough words.
+ */
+ if ((offset >= eeprom->word_size)
+ || (words > eeprom->word_size - offset) || (words == 0)) {
+ DEBUGOUT2
+ ("\"words\" parameter out of bounds. Words = %d, size = %d\n",
+ offset, eeprom->word_size);
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* EEPROM's that don't use EERD to read require us to bit-bang the SPI
+ * directly. In this case, we need to acquire the EEPROM so that
+ * FW or other port software does not interrupt.
+ */
+ /* Prepare the EEPROM for bit-bang reading */
+ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+
+ /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have
+ * acquired the EEPROM at this point, so any returns should release it */
+ if (eeprom->type == e1000_eeprom_spi) {
+ u16 word_in;
+ u8 read_opcode = EEPROM_READ_OPCODE_SPI;
+
+ if (e1000_spi_eeprom_ready(hw)) {
+ e1000_release_eeprom(hw);
+ return -E1000_ERR_EEPROM;
+ }
+
+ e1000_standby_eeprom(hw);
+
+ /* Some SPI eeproms use the 8th address bit embedded in the opcode */
+ if ((eeprom->address_bits == 8) && (offset >= 128))
+ read_opcode |= EEPROM_A8_OPCODE_SPI;
+
+ /* Send the READ command (opcode + addr) */
+ e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits);
+ e1000_shift_out_ee_bits(hw, (u16) (offset * 2),
+ eeprom->address_bits);
+
+ /* Read the data. The address of the eeprom internally increments with
+ * each byte (spi) being read, saving on the overhead of eeprom setup
+ * and tear-down. The address counter will roll over if reading beyond
+ * the size of the eeprom, thus allowing the entire memory to be read
+ * starting from any offset. */
+ for (i = 0; i < words; i++) {
+ word_in = e1000_shift_in_ee_bits(hw, 16);
+ data[i] = (word_in >> 8) | (word_in << 8);
+ }
+ } else if (eeprom->type == e1000_eeprom_microwire) {
+ for (i = 0; i < words; i++) {
+ /* Send the READ command (opcode + addr) */
+ e1000_shift_out_ee_bits(hw,
+ EEPROM_READ_OPCODE_MICROWIRE,
+ eeprom->opcode_bits);
+ e1000_shift_out_ee_bits(hw, (u16) (offset + i),
+ eeprom->address_bits);
+
+ /* Read the data. For microwire, each word requires the overhead
+ * of eeprom setup and tear-down. */
+ data[i] = e1000_shift_in_ee_bits(hw, 16);
+ e1000_standby_eeprom(hw);
+ }
+ }
+
+ /* End this read operation */
+ e1000_release_eeprom(hw);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_validate_eeprom_checksum - Verifies that the EEPROM has a valid checksum
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Reads the first 64 16 bit words of the EEPROM and sums the values read.
+ * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is
+ * valid.
+ */
+s32 e1000_validate_eeprom_checksum(struct e1000_hw *hw)
+{
+ u16 checksum = 0;
+ u16 i, eeprom_data;
+
+ DEBUGFUNC("e1000_validate_eeprom_checksum");
+
+ for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
+ if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ checksum += eeprom_data;
+ }
+
+ if (checksum == (u16) EEPROM_SUM)
+ return E1000_SUCCESS;
+ else {
+ DEBUGOUT("EEPROM Checksum Invalid\n");
+ return -E1000_ERR_EEPROM;
+ }
+}
+
+/**
+ * e1000_update_eeprom_checksum - Calculates/writes the EEPROM checksum
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Sums the first 63 16 bit words of the EEPROM. Subtracts the sum from 0xBABA.
+ * Writes the difference to word offset 63 of the EEPROM.
+ */
+s32 e1000_update_eeprom_checksum(struct e1000_hw *hw)
+{
+ u16 checksum = 0;
+ u16 i, eeprom_data;
+
+ DEBUGFUNC("e1000_update_eeprom_checksum");
+
+ for (i = 0; i < EEPROM_CHECKSUM_REG; i++) {
+ if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ checksum += eeprom_data;
+ }
+ checksum = (u16) EEPROM_SUM - checksum;
+ if (e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) {
+ DEBUGOUT("EEPROM Write Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_write_eeprom - write words to the different EEPROM types.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: 16 bit word to be written to the EEPROM
+ *
+ * If e1000_update_eeprom_checksum is not called after this function, the
+ * EEPROM will most likely contain an invalid checksum.
+ */
+s32 e1000_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ s32 ret;
+ spin_lock(&e1000_eeprom_lock);
+ ret = e1000_do_write_eeprom(hw, offset, words, data);
+ spin_unlock(&e1000_eeprom_lock);
+ return ret;
+}
+
+static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ s32 status = 0;
+
+ DEBUGFUNC("e1000_write_eeprom");
+
+ /* If eeprom is not yet detected, do so now */
+ if (eeprom->word_size == 0)
+ e1000_init_eeprom_params(hw);
+
+ /* A check for invalid values: offset too large, too many words, and not
+ * enough words.
+ */
+ if ((offset >= eeprom->word_size)
+ || (words > eeprom->word_size - offset) || (words == 0)) {
+ DEBUGOUT("\"words\" parameter out of bounds\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* Prepare the EEPROM for writing */
+ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+
+ if (eeprom->type == e1000_eeprom_microwire) {
+ status = e1000_write_eeprom_microwire(hw, offset, words, data);
+ } else {
+ status = e1000_write_eeprom_spi(hw, offset, words, data);
+ msleep(10);
+ }
+
+ /* Done with writing */
+ e1000_release_eeprom(hw);
+
+ return status;
+}
+
+/**
+ * e1000_write_eeprom_spi - Writes a 16 bit word to a given offset in an SPI EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: pointer to array of 8 bit words to be written to the EEPROM
+ */
+static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u16 widx = 0;
+
+ DEBUGFUNC("e1000_write_eeprom_spi");
+
+ while (widx < words) {
+ u8 write_opcode = EEPROM_WRITE_OPCODE_SPI;
+
+ if (e1000_spi_eeprom_ready(hw))
+ return -E1000_ERR_EEPROM;
+
+ e1000_standby_eeprom(hw);
+
+ /* Send the WRITE ENABLE command (8 bit opcode ) */
+ e1000_shift_out_ee_bits(hw, EEPROM_WREN_OPCODE_SPI,
+ eeprom->opcode_bits);
+
+ e1000_standby_eeprom(hw);
+
+ /* Some SPI eeproms use the 8th address bit embedded in the opcode */
+ if ((eeprom->address_bits == 8) && (offset >= 128))
+ write_opcode |= EEPROM_A8_OPCODE_SPI;
+
+ /* Send the Write command (8-bit opcode + addr) */
+ e1000_shift_out_ee_bits(hw, write_opcode, eeprom->opcode_bits);
+
+ e1000_shift_out_ee_bits(hw, (u16) ((offset + widx) * 2),
+ eeprom->address_bits);
+
+ /* Send the data */
+
+ /* Loop to allow for up to whole page write (32 bytes) of eeprom */
+ while (widx < words) {
+ u16 word_out = data[widx];
+ word_out = (word_out >> 8) | (word_out << 8);
+ e1000_shift_out_ee_bits(hw, word_out, 16);
+ widx++;
+
+ /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE
+ * operation, while the smaller eeproms are capable of an 8-byte
+ * PAGE WRITE operation. Break the inner loop to pass new address
+ */
+ if ((((offset + widx) * 2) % eeprom->page_size) == 0) {
+ e1000_standby_eeprom(hw);
+ break;
+ }
+ }
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_write_eeprom_microwire - Writes a 16 bit word to a given offset in a Microwire EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: pointer to array of 8 bit words to be written to the EEPROM
+ */
+static s32 e1000_write_eeprom_microwire(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd;
+ u16 words_written = 0;
+ u16 i = 0;
+
+ DEBUGFUNC("e1000_write_eeprom_microwire");
+
+ /* Send the write enable command to the EEPROM (3-bit opcode plus
+ * 6/8-bit dummy address beginning with 11). It's less work to include
+ * the 11 of the dummy address as part of the opcode than it is to shift
+ * it over the correct number of bits for the address. This puts the
+ * EEPROM into write/erase mode.
+ */
+ e1000_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE_MICROWIRE,
+ (u16) (eeprom->opcode_bits + 2));
+
+ e1000_shift_out_ee_bits(hw, 0, (u16) (eeprom->address_bits - 2));
+
+ /* Prepare the EEPROM */
+ e1000_standby_eeprom(hw);
+
+ while (words_written < words) {
+ /* Send the Write command (3-bit opcode + addr) */
+ e1000_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE_MICROWIRE,
+ eeprom->opcode_bits);
+
+ e1000_shift_out_ee_bits(hw, (u16) (offset + words_written),
+ eeprom->address_bits);
+
+ /* Send the data */
+ e1000_shift_out_ee_bits(hw, data[words_written], 16);
+
+ /* Toggle the CS line. This in effect tells the EEPROM to execute
+ * the previous command.
+ */
+ e1000_standby_eeprom(hw);
+
+ /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will
+ * signal that the command has been completed by raising the DO signal.
+ * If DO does not go high in 10 milliseconds, then error out.
+ */
+ for (i = 0; i < 200; i++) {
+ eecd = er32(EECD);
+ if (eecd & E1000_EECD_DO)
+ break;
+ udelay(50);
+ }
+ if (i == 200) {
+ DEBUGOUT("EEPROM Write did not complete\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* Recover from write */
+ e1000_standby_eeprom(hw);
+
+ words_written++;
+ }
+
+ /* Send the write disable command to the EEPROM (3-bit opcode plus
+ * 6/8-bit dummy address beginning with 10). It's less work to include
+ * the 10 of the dummy address as part of the opcode than it is to shift
+ * it over the correct number of bits for the address. This takes the
+ * EEPROM out of write/erase mode.
+ */
+ e1000_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE_MICROWIRE,
+ (u16) (eeprom->opcode_bits + 2));
+
+ e1000_shift_out_ee_bits(hw, 0, (u16) (eeprom->address_bits - 2));
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_read_mac_addr - read the adapters MAC from eeprom
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
+ * second function of dual function devices
+ */
+s32 e1000_read_mac_addr(struct e1000_hw *hw)
+{
+ u16 offset;
+ u16 eeprom_data, i;
+
+ DEBUGFUNC("e1000_read_mac_addr");
+
+ for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
+ offset = i >> 1;
+ if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ hw->perm_mac_addr[i] = (u8) (eeprom_data & 0x00FF);
+ hw->perm_mac_addr[i + 1] = (u8) (eeprom_data >> 8);
+ }
+
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ if (er32(STATUS) & E1000_STATUS_FUNC_1)
+ hw->perm_mac_addr[5] ^= 0x01;
+ break;
+ }
+
+ for (i = 0; i < NODE_ADDRESS_SIZE; i++)
+ hw->mac_addr[i] = hw->perm_mac_addr[i];
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_init_rx_addrs - Initializes receive address filters.
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Places the MAC address in receive address register 0 and clears the rest
+ * of the receive address registers. Clears the multicast table. Assumes
+ * the receiver is in reset when the routine is called.
+ */
+static void e1000_init_rx_addrs(struct e1000_hw *hw)
+{
+ u32 i;
+ u32 rar_num;
+
+ DEBUGFUNC("e1000_init_rx_addrs");
+
+ /* Setup the receive address. */
+ DEBUGOUT("Programming MAC Address into RAR[0]\n");
+
+ e1000_rar_set(hw, hw->mac_addr, 0);
+
+ rar_num = E1000_RAR_ENTRIES;
+
+ /* Zero out the other 15 receive addresses. */
+ DEBUGOUT("Clearing RAR[1-15]\n");
+ for (i = 1; i < rar_num; i++) {
+ E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
+ E1000_WRITE_FLUSH();
+ E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
+ E1000_WRITE_FLUSH();
+ }
+}
+
+/**
+ * e1000_hash_mc_addr - Hashes an address to determine its location in the multicast table
+ * @hw: Struct containing variables accessed by shared code
+ * @mc_addr: the multicast address to hash
+ */
+u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
+{
+ u32 hash_value = 0;
+
+ /* The portion of the address that is used for the hash table is
+ * determined by the mc_filter_type setting.
+ */
+ switch (hw->mc_filter_type) {
+ /* [0] [1] [2] [3] [4] [5]
+ * 01 AA 00 12 34 56
+ * LSB MSB
+ */
+ case 0:
+ /* [47:36] i.e. 0x563 for above example address */
+ hash_value = ((mc_addr[4] >> 4) | (((u16) mc_addr[5]) << 4));
+ break;
+ case 1:
+ /* [46:35] i.e. 0xAC6 for above example address */
+ hash_value = ((mc_addr[4] >> 3) | (((u16) mc_addr[5]) << 5));
+ break;
+ case 2:
+ /* [45:34] i.e. 0x5D8 for above example address */
+ hash_value = ((mc_addr[4] >> 2) | (((u16) mc_addr[5]) << 6));
+ break;
+ case 3:
+ /* [43:32] i.e. 0x634 for above example address */
+ hash_value = ((mc_addr[4]) | (((u16) mc_addr[5]) << 8));
+ break;
+ }
+
+ hash_value &= 0xFFF;
+ return hash_value;
+}
+
+/**
+ * e1000_rar_set - Puts an ethernet address into a receive address register.
+ * @hw: Struct containing variables accessed by shared code
+ * @addr: Address to put into receive address register
+ * @index: Receive address register to write
+ */
+void e1000_rar_set(struct e1000_hw *hw, u8 *addr, u32 index)
+{
+ u32 rar_low, rar_high;
+
+ /* HW expects these in little endian so we reverse the byte order
+ * from network order (big endian) to little endian
+ */
+ rar_low = ((u32) addr[0] | ((u32) addr[1] << 8) |
+ ((u32) addr[2] << 16) | ((u32) addr[3] << 24));
+ rar_high = ((u32) addr[4] | ((u32) addr[5] << 8));
+
+ /* Disable Rx and flush all Rx frames before enabling RSS to avoid Rx
+ * unit hang.
+ *
+ * Description:
+ * If there are any Rx frames queued up or otherwise present in the HW
+ * before RSS is enabled, and then we enable RSS, the HW Rx unit will
+ * hang. To work around this issue, we have to disable receives and
+ * flush out all Rx frames before we enable RSS. To do so, we modify we
+ * redirect all Rx traffic to manageability and then reset the HW.
+ * This flushes away Rx frames, and (since the redirections to
+ * manageability persists across resets) keeps new ones from coming in
+ * while we work. Then, we clear the Address Valid AV bit for all MAC
+ * addresses and undo the re-direction to manageability.
+ * Now, frames are coming in again, but the MAC won't accept them, so
+ * far so good. We now proceed to initialize RSS (if necessary) and
+ * configure the Rx unit. Last, we re-enable the AV bits and continue
+ * on our merry way.
+ */
+ switch (hw->mac_type) {
+ default:
+ /* Indicate to hardware the Address is Valid. */
+ rar_high |= E1000_RAH_AV;
+ break;
+ }
+
+ E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low);
+ E1000_WRITE_FLUSH();
+ E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high);
+ E1000_WRITE_FLUSH();
+}
+
+/**
+ * e1000_write_vfta - Writes a value to the specified offset in the VLAN filter table.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: Offset in VLAN filer table to write
+ * @value: Value to write into VLAN filter table
+ */
+void e1000_write_vfta(struct e1000_hw *hw, u32 offset, u32 value)
+{
+ u32 temp;
+
+ if ((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) {
+ temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1));
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
+ E1000_WRITE_FLUSH();
+ E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp);
+ E1000_WRITE_FLUSH();
+ } else {
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
+ E1000_WRITE_FLUSH();
+ }
+}
+
+/**
+ * e1000_clear_vfta - Clears the VLAN filer table
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_clear_vfta(struct e1000_hw *hw)
+{
+ u32 offset;
+ u32 vfta_value = 0;
+ u32 vfta_offset = 0;
+ u32 vfta_bit_in_reg = 0;
+
+ for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+ /* If the offset we want to clear is the same offset of the
+ * manageability VLAN ID, then clear all bits except that of the
+ * manageability unit */
+ vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value);
+ E1000_WRITE_FLUSH();
+ }
+}
+
+static s32 e1000_id_led_init(struct e1000_hw *hw)
+{
+ u32 ledctl;
+ const u32 ledctl_mask = 0x000000FF;
+ const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON;
+ const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF;
+ u16 eeprom_data, i, temp;
+ const u16 led_mask = 0x0F;
+
+ DEBUGFUNC("e1000_id_led_init");
+
+ if (hw->mac_type < e1000_82540) {
+ /* Nothing to do */
+ return E1000_SUCCESS;
+ }
+
+ ledctl = er32(LEDCTL);
+ hw->ledctl_default = ledctl;
+ hw->ledctl_mode1 = hw->ledctl_default;
+ hw->ledctl_mode2 = hw->ledctl_default;
+
+ if (e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ if ((eeprom_data == ID_LED_RESERVED_0000) ||
+ (eeprom_data == ID_LED_RESERVED_FFFF)) {
+ eeprom_data = ID_LED_DEFAULT;
+ }
+
+ for (i = 0; i < 4; i++) {
+ temp = (eeprom_data >> (i << 2)) & led_mask;
+ switch (temp) {
+ case ID_LED_ON1_DEF2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_ON1_OFF2:
+ hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode1 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_OFF1_DEF2:
+ case ID_LED_OFF1_ON2:
+ case ID_LED_OFF1_OFF2:
+ hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode1 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ switch (temp) {
+ case ID_LED_DEF1_ON2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_OFF1_ON2:
+ hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode2 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_DEF1_OFF2:
+ case ID_LED_ON1_OFF2:
+ case ID_LED_OFF1_OFF2:
+ hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode2 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_setup_led
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Prepares SW controlable LED for use and saves the current state of the LED.
+ */
+s32 e1000_setup_led(struct e1000_hw *hw)
+{
+ u32 ledctl;
+ s32 ret_val = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_setup_led");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ /* No setup necessary */
+ break;
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ /* Turn off PHY Smart Power Down (if enabled) */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ &hw->phy_spd_default);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ (u16) (hw->phy_spd_default &
+ ~IGP01E1000_GMII_SPD));
+ if (ret_val)
+ return ret_val;
+ /* Fall Through */
+ default:
+ if (hw->media_type == e1000_media_type_fiber) {
+ ledctl = er32(LEDCTL);
+ /* Save current LEDCTL settings */
+ hw->ledctl_default = ledctl;
+ /* Turn off LED0 */
+ ledctl &= ~(E1000_LEDCTL_LED0_IVRT |
+ E1000_LEDCTL_LED0_BLINK |
+ E1000_LEDCTL_LED0_MODE_MASK);
+ ledctl |= (E1000_LEDCTL_MODE_LED_OFF <<
+ E1000_LEDCTL_LED0_MODE_SHIFT);
+ ew32(LEDCTL, ledctl);
+ } else if (hw->media_type == e1000_media_type_copper)
+ ew32(LEDCTL, hw->ledctl_mode1);
+ break;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_cleanup_led - Restores the saved state of the SW controlable LED.
+ * @hw: Struct containing variables accessed by shared code
+ */
+s32 e1000_cleanup_led(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_cleanup_led");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ /* No cleanup necessary */
+ break;
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ /* Turn on PHY Smart Power Down (if previously enabled) */
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ hw->phy_spd_default);
+ if (ret_val)
+ return ret_val;
+ /* Fall Through */
+ default:
+ /* Restore LEDCTL settings */
+ ew32(LEDCTL, hw->ledctl_default);
+ break;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_led_on - Turns on the software controllable LED
+ * @hw: Struct containing variables accessed by shared code
+ */
+s32 e1000_led_on(struct e1000_hw *hw)
+{
+ u32 ctrl = er32(CTRL);
+
+ DEBUGFUNC("e1000_led_on");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ /* Set SW Defineable Pin 0 to turn on the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ break;
+ case e1000_82544:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Set SW Defineable Pin 0 to turn on the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else {
+ /* Clear SW Defineable Pin 0 to turn on the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ }
+ break;
+ default:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Clear SW Defineable Pin 0 to turn on the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else if (hw->media_type == e1000_media_type_copper) {
+ ew32(LEDCTL, hw->ledctl_mode2);
+ return E1000_SUCCESS;
+ }
+ break;
+ }
+
+ ew32(CTRL, ctrl);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_led_off - Turns off the software controllable LED
+ * @hw: Struct containing variables accessed by shared code
+ */
+s32 e1000_led_off(struct e1000_hw *hw)
+{
+ u32 ctrl = er32(CTRL);
+
+ DEBUGFUNC("e1000_led_off");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ /* Clear SW Defineable Pin 0 to turn off the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ break;
+ case e1000_82544:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Clear SW Defineable Pin 0 to turn off the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else {
+ /* Set SW Defineable Pin 0 to turn off the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ }
+ break;
+ default:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Set SW Defineable Pin 0 to turn off the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else if (hw->media_type == e1000_media_type_copper) {
+ ew32(LEDCTL, hw->ledctl_mode1);
+ return E1000_SUCCESS;
+ }
+ break;
+ }
+
+ ew32(CTRL, ctrl);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_clear_hw_cntrs - Clears all hardware statistics counters.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_clear_hw_cntrs(struct e1000_hw *hw)
+{
+ volatile u32 temp;
+
+ temp = er32(CRCERRS);
+ temp = er32(SYMERRS);
+ temp = er32(MPC);
+ temp = er32(SCC);
+ temp = er32(ECOL);
+ temp = er32(MCC);
+ temp = er32(LATECOL);
+ temp = er32(COLC);
+ temp = er32(DC);
+ temp = er32(SEC);
+ temp = er32(RLEC);
+ temp = er32(XONRXC);
+ temp = er32(XONTXC);
+ temp = er32(XOFFRXC);
+ temp = er32(XOFFTXC);
+ temp = er32(FCRUC);
+
+ temp = er32(PRC64);
+ temp = er32(PRC127);
+ temp = er32(PRC255);
+ temp = er32(PRC511);
+ temp = er32(PRC1023);
+ temp = er32(PRC1522);
+
+ temp = er32(GPRC);
+ temp = er32(BPRC);
+ temp = er32(MPRC);
+ temp = er32(GPTC);
+ temp = er32(GORCL);
+ temp = er32(GORCH);
+ temp = er32(GOTCL);
+ temp = er32(GOTCH);
+ temp = er32(RNBC);
+ temp = er32(RUC);
+ temp = er32(RFC);
+ temp = er32(ROC);
+ temp = er32(RJC);
+ temp = er32(TORL);
+ temp = er32(TORH);
+ temp = er32(TOTL);
+ temp = er32(TOTH);
+ temp = er32(TPR);
+ temp = er32(TPT);
+
+ temp = er32(PTC64);
+ temp = er32(PTC127);
+ temp = er32(PTC255);
+ temp = er32(PTC511);
+ temp = er32(PTC1023);
+ temp = er32(PTC1522);
+
+ temp = er32(MPTC);
+ temp = er32(BPTC);
+
+ if (hw->mac_type < e1000_82543)
+ return;
+
+ temp = er32(ALGNERRC);
+ temp = er32(RXERRC);
+ temp = er32(TNCRS);
+ temp = er32(CEXTERR);
+ temp = er32(TSCTC);
+ temp = er32(TSCTFC);
+
+ if (hw->mac_type <= e1000_82544)
+ return;
+
+ temp = er32(MGTPRC);
+ temp = er32(MGTPDC);
+ temp = er32(MGTPTC);
+}
+
+/**
+ * e1000_reset_adaptive - Resets Adaptive IFS to its default state.
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Call this after e1000_init_hw. You may override the IFS defaults by setting
+ * hw->ifs_params_forced to true. However, you must initialize hw->
+ * current_ifs_val, ifs_min_val, ifs_max_val, ifs_step_size, and ifs_ratio
+ * before calling this function.
+ */
+void e1000_reset_adaptive(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_reset_adaptive");
+
+ if (hw->adaptive_ifs) {
+ if (!hw->ifs_params_forced) {
+ hw->current_ifs_val = 0;
+ hw->ifs_min_val = IFS_MIN;
+ hw->ifs_max_val = IFS_MAX;
+ hw->ifs_step_size = IFS_STEP;
+ hw->ifs_ratio = IFS_RATIO;
+ }
+ hw->in_ifs_mode = false;
+ ew32(AIT, 0);
+ } else {
+ DEBUGOUT("Not in Adaptive IFS mode!\n");
+ }
+}
+
+/**
+ * e1000_update_adaptive - update adaptive IFS
+ * @hw: Struct containing variables accessed by shared code
+ * @tx_packets: Number of transmits since last callback
+ * @total_collisions: Number of collisions since last callback
+ *
+ * Called during the callback/watchdog routine to update IFS value based on
+ * the ratio of transmits to collisions.
+ */
+void e1000_update_adaptive(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_update_adaptive");
+
+ if (hw->adaptive_ifs) {
+ if ((hw->collision_delta *hw->ifs_ratio) > hw->tx_packet_delta) {
+ if (hw->tx_packet_delta > MIN_NUM_XMITS) {
+ hw->in_ifs_mode = true;
+ if (hw->current_ifs_val < hw->ifs_max_val) {
+ if (hw->current_ifs_val == 0)
+ hw->current_ifs_val =
+ hw->ifs_min_val;
+ else
+ hw->current_ifs_val +=
+ hw->ifs_step_size;
+ ew32(AIT, hw->current_ifs_val);
+ }
+ }
+ } else {
+ if (hw->in_ifs_mode
+ && (hw->tx_packet_delta <= MIN_NUM_XMITS)) {
+ hw->current_ifs_val = 0;
+ hw->in_ifs_mode = false;
+ ew32(AIT, 0);
+ }
+ }
+ } else {
+ DEBUGOUT("Not in Adaptive IFS mode!\n");
+ }
+}
+
+/**
+ * e1000_tbi_adjust_stats
+ * @hw: Struct containing variables accessed by shared code
+ * @frame_len: The length of the frame in question
+ * @mac_addr: The Ethernet destination address of the frame in question
+ *
+ * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT
+ */
+void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats,
+ u32 frame_len, u8 *mac_addr)
+{
+ u64 carry_bit;
+
+ /* First adjust the frame length. */
+ frame_len--;
+ /* We need to adjust the statistics counters, since the hardware
+ * counters overcount this packet as a CRC error and undercount
+ * the packet as a good packet
+ */
+ /* This packet should not be counted as a CRC error. */
+ stats->crcerrs--;
+ /* This packet does count as a Good Packet Received. */
+ stats->gprc++;
+
+ /* Adjust the Good Octets received counters */
+ carry_bit = 0x80000000 & stats->gorcl;
+ stats->gorcl += frame_len;
+ /* If the high bit of Gorcl (the low 32 bits of the Good Octets
+ * Received Count) was one before the addition,
+ * AND it is zero after, then we lost the carry out,
+ * need to add one to Gorch (Good Octets Received Count High).
+ * This could be simplified if all environments supported
+ * 64-bit integers.
+ */
+ if (carry_bit && ((stats->gorcl & 0x80000000) == 0))
+ stats->gorch++;
+ /* Is this a broadcast or multicast? Check broadcast first,
+ * since the test for a multicast frame will test positive on
+ * a broadcast frame.
+ */
+ if ((mac_addr[0] == (u8) 0xff) && (mac_addr[1] == (u8) 0xff))
+ /* Broadcast packet */
+ stats->bprc++;
+ else if (*mac_addr & 0x01)
+ /* Multicast packet */
+ stats->mprc++;
+
+ if (frame_len == hw->max_frame_size) {
+ /* In this case, the hardware has overcounted the number of
+ * oversize frames.
+ */
+ if (stats->roc > 0)
+ stats->roc--;
+ }
+
+ /* Adjust the bin counters when the extra byte put the frame in the
+ * wrong bin. Remember that the frame_len was adjusted above.
+ */
+ if (frame_len == 64) {
+ stats->prc64++;
+ stats->prc127--;
+ } else if (frame_len == 127) {
+ stats->prc127++;
+ stats->prc255--;
+ } else if (frame_len == 255) {
+ stats->prc255++;
+ stats->prc511--;
+ } else if (frame_len == 511) {
+ stats->prc511++;
+ stats->prc1023--;
+ } else if (frame_len == 1023) {
+ stats->prc1023++;
+ stats->prc1522--;
+ } else if (frame_len == 1522) {
+ stats->prc1522++;
+ }
+}
+
+/**
+ * e1000_get_bus_info
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Gets the current PCI bus type, speed, and width of the hardware
+ */
+void e1000_get_bus_info(struct e1000_hw *hw)
+{
+ u32 status;
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ hw->bus_type = e1000_bus_type_pci;
+ hw->bus_speed = e1000_bus_speed_unknown;
+ hw->bus_width = e1000_bus_width_unknown;
+ break;
+ default:
+ status = er32(STATUS);
+ hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ?
+ e1000_bus_type_pcix : e1000_bus_type_pci;
+
+ if (hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) {
+ hw->bus_speed = (hw->bus_type == e1000_bus_type_pci) ?
+ e1000_bus_speed_66 : e1000_bus_speed_120;
+ } else if (hw->bus_type == e1000_bus_type_pci) {
+ hw->bus_speed = (status & E1000_STATUS_PCI66) ?
+ e1000_bus_speed_66 : e1000_bus_speed_33;
+ } else {
+ switch (status & E1000_STATUS_PCIX_SPEED) {
+ case E1000_STATUS_PCIX_SPEED_66:
+ hw->bus_speed = e1000_bus_speed_66;
+ break;
+ case E1000_STATUS_PCIX_SPEED_100:
+ hw->bus_speed = e1000_bus_speed_100;
+ break;
+ case E1000_STATUS_PCIX_SPEED_133:
+ hw->bus_speed = e1000_bus_speed_133;
+ break;
+ default:
+ hw->bus_speed = e1000_bus_speed_reserved;
+ break;
+ }
+ }
+ hw->bus_width = (status & E1000_STATUS_BUS64) ?
+ e1000_bus_width_64 : e1000_bus_width_32;
+ break;
+ }
+}
+
+/**
+ * e1000_write_reg_io
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset to write to
+ * @value: value to write
+ *
+ * Writes a value to one of the devices registers using port I/O (as opposed to
+ * memory mapped I/O). Only 82544 and newer devices support port I/O.
+ */
+static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value)
+{
+ unsigned long io_addr = hw->io_base;
+ unsigned long io_data = hw->io_base + 4;
+
+ e1000_io_write(hw, io_addr, offset);
+ e1000_io_write(hw, io_data, value);
+}
+
+/**
+ * e1000_get_cable_length - Estimates the cable length.
+ * @hw: Struct containing variables accessed by shared code
+ * @min_length: The estimated minimum length
+ * @max_length: The estimated maximum length
+ *
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
+ *
+ * This function always returns a ranged length (minimum & maximum).
+ * So for M88 phy's, this function interprets the one value returned from the
+ * register to the minimum and maximum range.
+ * For IGP phy's, the function calculates the range by the AGC registers.
+ */
+static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length,
+ u16 *max_length)
+{
+ s32 ret_val;
+ u16 agc_value = 0;
+ u16 i, phy_data;
+ u16 cable_length;
+
+ DEBUGFUNC("e1000_get_cable_length");
+
+ *min_length = *max_length = 0;
+
+ /* Use old method for Phy older than IGP */
+ if (hw->phy_type == e1000_phy_m88) {
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ cable_length = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT;
+
+ /* Convert the enum value to ranged values */
+ switch (cable_length) {
+ case e1000_cable_length_50:
+ *min_length = 0;
+ *max_length = e1000_igp_cable_length_50;
+ break;
+ case e1000_cable_length_50_80:
+ *min_length = e1000_igp_cable_length_50;
+ *max_length = e1000_igp_cable_length_80;
+ break;
+ case e1000_cable_length_80_110:
+ *min_length = e1000_igp_cable_length_80;
+ *max_length = e1000_igp_cable_length_110;
+ break;
+ case e1000_cable_length_110_140:
+ *min_length = e1000_igp_cable_length_110;
+ *max_length = e1000_igp_cable_length_140;
+ break;
+ case e1000_cable_length_140:
+ *min_length = e1000_igp_cable_length_140;
+ *max_length = e1000_igp_cable_length_170;
+ break;
+ default:
+ return -E1000_ERR_PHY;
+ break;
+ }
+ } else if (hw->phy_type == e1000_phy_igp) { /* For IGP PHY */
+ u16 cur_agc_value;
+ u16 min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
+ u16 agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
+ { IGP01E1000_PHY_AGC_A,
+ IGP01E1000_PHY_AGC_B,
+ IGP01E1000_PHY_AGC_C,
+ IGP01E1000_PHY_AGC_D
+ };
+ /* Read the AGC registers for all channels */
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+
+ ret_val =
+ e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT;
+
+ /* Value bound check. */
+ if ((cur_agc_value >=
+ IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1)
+ || (cur_agc_value == 0))
+ return -E1000_ERR_PHY;
+
+ agc_value += cur_agc_value;
+
+ /* Update minimal AGC value. */
+ if (min_agc_value > cur_agc_value)
+ min_agc_value = cur_agc_value;
+ }
+
+ /* Remove the minimal AGC result for length < 50m */
+ if (agc_value <
+ IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) {
+ agc_value -= min_agc_value;
+
+ /* Get the average length of the remaining 3 channels */
+ agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1);
+ } else {
+ /* Get the average length of all the 4 channels. */
+ agc_value /= IGP01E1000_PHY_CHANNEL_NUM;
+ }
+
+ /* Set the range of the calculated length. */
+ *min_length = ((e1000_igp_cable_length_table[agc_value] -
+ IGP01E1000_AGC_RANGE) > 0) ?
+ (e1000_igp_cable_length_table[agc_value] -
+ IGP01E1000_AGC_RANGE) : 0;
+ *max_length = e1000_igp_cable_length_table[agc_value] +
+ IGP01E1000_AGC_RANGE;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_check_polarity - Check the cable polarity
+ * @hw: Struct containing variables accessed by shared code
+ * @polarity: output parameter : 0 - Polarity is not reversed
+ * 1 - Polarity is reversed.
+ *
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
+ *
+ * For phy's older than IGP, this function simply reads the polarity bit in the
+ * Phy Status register. For IGP phy's, this bit is valid only if link speed is
+ * 10 Mbps. If the link speed is 100 Mbps there is no polarity so this bit will
+ * return 0. If the link speed is 1000 Mbps the polarity status is in the
+ * IGP01E1000_PHY_PCS_INIT_REG.
+ */
+static s32 e1000_check_polarity(struct e1000_hw *hw,
+ e1000_rev_polarity *polarity)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_check_polarity");
+
+ if (hw->phy_type == e1000_phy_m88) {
+ /* return the Polarity bit in the Status register. */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ *polarity = ((phy_data & M88E1000_PSSR_REV_POLARITY) >>
+ M88E1000_PSSR_REV_POLARITY_SHIFT) ?
+ e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
+
+ } else if (hw->phy_type == e1000_phy_igp) {
+ /* Read the Status register to check the speed */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to
+ * find the polarity status */
+ if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+
+ /* Read the GIG initialization PCS register (0x00B4) */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Check the polarity bits */
+ *polarity = (phy_data & IGP01E1000_PHY_POLARITY_MASK) ?
+ e1000_rev_polarity_reversed :
+ e1000_rev_polarity_normal;
+ } else {
+ /* For 10 Mbps, read the polarity bit in the status register. (for
+ * 100 Mbps this bit is always 0) */
+ *polarity =
+ (phy_data & IGP01E1000_PSSR_POLARITY_REVERSED) ?
+ e1000_rev_polarity_reversed :
+ e1000_rev_polarity_normal;
+ }
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_check_downshift - Check if Downshift occurred
+ * @hw: Struct containing variables accessed by shared code
+ * @downshift: output parameter : 0 - No Downshift occurred.
+ * 1 - Downshift occurred.
+ *
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
+ *
+ * For phy's older than IGP, this function reads the Downshift bit in the Phy
+ * Specific Status register. For IGP phy's, it reads the Downgrade bit in the
+ * Link Health register. In IGP this bit is latched high, so the driver must
+ * read it immediately after link is established.
+ */
+static s32 e1000_check_downshift(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_check_downshift");
+
+ if (hw->phy_type == e1000_phy_igp) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ hw->speed_downgraded =
+ (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0;
+ } else if (hw->phy_type == e1000_phy_m88) {
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >>
+ M88E1000_PSSR_DOWNSHIFT_SHIFT;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_config_dsp_after_link_change
+ * @hw: Struct containing variables accessed by shared code
+ * @link_up: was link up at the time this was called
+ *
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * E1000_SUCCESS at any other case.
+ *
+ * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a
+ * gigabit link is achieved to improve link quality.
+ */
+
+static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up)
+{
+ s32 ret_val;
+ u16 phy_data, phy_saved_data, speed, duplex, i;
+ u16 dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
+ { IGP01E1000_PHY_AGC_PARAM_A,
+ IGP01E1000_PHY_AGC_PARAM_B,
+ IGP01E1000_PHY_AGC_PARAM_C,
+ IGP01E1000_PHY_AGC_PARAM_D
+ };
+ u16 min_length, max_length;
+
+ DEBUGFUNC("e1000_config_dsp_after_link_change");
+
+ if (hw->phy_type != e1000_phy_igp)
+ return E1000_SUCCESS;
+
+ if (link_up) {
+ ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if (ret_val) {
+ DEBUGOUT("Error getting link speed and duplex\n");
+ return ret_val;
+ }
+
+ if (speed == SPEED_1000) {
+
+ ret_val =
+ e1000_get_cable_length(hw, &min_length,
+ &max_length);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->dsp_config_state == e1000_dsp_config_enabled)
+ && min_length >= e1000_igp_cable_length_50) {
+
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val =
+ e1000_read_phy_reg(hw,
+ dsp_reg_array[i],
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &=
+ ~IGP01E1000_PHY_EDAC_MU_INDEX;
+
+ ret_val =
+ e1000_write_phy_reg(hw,
+ dsp_reg_array
+ [i], phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ hw->dsp_config_state =
+ e1000_dsp_config_activated;
+ }
+
+ if ((hw->ffe_config_state == e1000_ffe_config_enabled)
+ && (min_length < e1000_igp_cable_length_50)) {
+
+ u16 ffe_idle_err_timeout =
+ FFE_IDLE_ERR_COUNT_TIMEOUT_20;
+ u32 idle_errs = 0;
+
+ /* clear previous idle error counts */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_1000T_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ for (i = 0; i < ffe_idle_err_timeout; i++) {
+ udelay(1000);
+ ret_val =
+ e1000_read_phy_reg(hw,
+ PHY_1000T_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ idle_errs +=
+ (phy_data &
+ SR_1000T_IDLE_ERROR_CNT);
+ if (idle_errs >
+ SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT)
+ {
+ hw->ffe_config_state =
+ e1000_ffe_config_active;
+
+ ret_val =
+ e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_DSP_FFE,
+ IGP01E1000_PHY_DSP_FFE_CM_CP);
+ if (ret_val)
+ return ret_val;
+ break;
+ }
+
+ if (idle_errs)
+ ffe_idle_err_timeout =
+ FFE_IDLE_ERR_COUNT_TIMEOUT_100;
+ }
+ }
+ }
+ } else {
+ if (hw->dsp_config_state == e1000_dsp_config_activated) {
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of the routines. */
+ ret_val =
+ e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
+
+ if (ret_val)
+ return ret_val;
+
+ /* Disable the PHY transmitter */
+ ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
+
+ if (ret_val)
+ return ret_val;
+
+ mdelay(20);
+
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_FORCE_GIGA);
+ if (ret_val)
+ return ret_val;
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val =
+ e1000_read_phy_reg(hw, dsp_reg_array[i],
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX;
+ phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS;
+
+ ret_val =
+ e1000_write_phy_reg(hw, dsp_reg_array[i],
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_RESTART_AUTONEG);
+ if (ret_val)
+ return ret_val;
+
+ mdelay(20);
+
+ /* Now enable the transmitter */
+ ret_val =
+ e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
+
+ if (ret_val)
+ return ret_val;
+
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+ }
+
+ if (hw->ffe_config_state == e1000_ffe_config_active) {
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of the routines. */
+ ret_val =
+ e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
+
+ if (ret_val)
+ return ret_val;
+
+ /* Disable the PHY transmitter */
+ ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
+
+ if (ret_val)
+ return ret_val;
+
+ mdelay(20);
+
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_FORCE_GIGA);
+ if (ret_val)
+ return ret_val;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_DSP_FFE,
+ IGP01E1000_PHY_DSP_FFE_DEFAULT);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_RESTART_AUTONEG);
+ if (ret_val)
+ return ret_val;
+
+ mdelay(20);
+
+ /* Now enable the transmitter */
+ ret_val =
+ e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
+
+ if (ret_val)
+ return ret_val;
+
+ hw->ffe_config_state = e1000_ffe_config_enabled;
+ }
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_set_phy_mode - Set PHY to class A mode
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Assumes the following operations will follow to enable the new class mode.
+ * 1. Do a PHY soft reset
+ * 2. Restart auto-negotiation or force link.
+ */
+static s32 e1000_set_phy_mode(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 eeprom_data;
+
+ DEBUGFUNC("e1000_set_phy_mode");
+
+ if ((hw->mac_type == e1000_82545_rev_3) &&
+ (hw->media_type == e1000_media_type_copper)) {
+ ret_val =
+ e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1,
+ &eeprom_data);
+ if (ret_val) {
+ return ret_val;
+ }
+
+ if ((eeprom_data != EEPROM_RESERVED_WORD) &&
+ (eeprom_data & EEPROM_PHY_CLASS_A)) {
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT,
+ 0x000B);
+ if (ret_val)
+ return ret_val;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL,
+ 0x8104);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy_reset_disable = false;
+ }
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_set_d3_lplu_state - set d3 link power state
+ * @hw: Struct containing variables accessed by shared code
+ * @active: true to enable lplu false to disable lplu.
+ *
+ * This function sets the lplu state according to the active flag. When
+ * activating lplu this function also disables smart speed and vise versa.
+ * lplu will not be activated unless the device autonegotiation advertisement
+ * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
+ *
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * E1000_SUCCESS at any other case.
+ */
+static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active)
+{
+ s32 ret_val;
+ u16 phy_data;
+ DEBUGFUNC("e1000_set_d3_lplu_state");
+
+ if (hw->phy_type != e1000_phy_igp)
+ return E1000_SUCCESS;
+
+ /* During driver activity LPLU should not be used or it will attain link
+ * from the lowest speeds starting from 10Mbps. The capability is used for
+ * Dx transitions and states */
+ if (hw->mac_type == e1000_82541_rev_2
+ || hw->mac_type == e1000_82547_rev_2) {
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ if (!active) {
+ if (hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
+ * Dx states where the power conservation is most important. During
+ * driver activity we should enable SmartSpeed, so performance is
+ * maintained. */
+ if (hw->smart_speed == e1000_smart_speed_on) {
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->smart_speed == e1000_smart_speed_off) {
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT)
+ || (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL)
+ || (hw->autoneg_advertised ==
+ AUTONEG_ADVERTISE_10_100_ALL)) {
+
+ if (hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data |= IGP01E1000_GMII_FLEX_SPD;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* When LPLU is enabled we should disable SmartSpeed */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_set_vco_speed
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Change VCO speed register to improve Bit Error Rate performance of SERDES.
+ */
+static s32 e1000_set_vco_speed(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 default_page = 0;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_set_vco_speed");
+
+ switch (hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
+ return E1000_SUCCESS;
+ }
+
+ /* Set PHY register 30, page 5, bit 8 to 0 */
+
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~M88E1000_PHY_VCO_REG_BIT8;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Set PHY register 30, page 4, bit 11 to 1 */
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PHY_VCO_REG_BIT11;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, default_page);
+ if (ret_val)
+ return ret_val;
+
+ return E1000_SUCCESS;
+}
+
+
+/**
+ * e1000_enable_mng_pass_thru - check for bmc pass through
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Verifies the hardware needs to allow ARPs to be processed by the host
+ * returns: - true/false
+ */
+u32 e1000_enable_mng_pass_thru(struct e1000_hw *hw)
+{
+ u32 manc;
+
+ if (hw->asf_firmware_present) {
+ manc = er32(MANC);
+
+ if (!(manc & E1000_MANC_RCV_TCO_EN) ||
+ !(manc & E1000_MANC_EN_MAC_ADDR_FILTER))
+ return false;
+ if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN))
+ return true;
+ }
+ return false;
+}
+
+static s32 e1000_polarity_reversal_workaround(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 mii_status_reg;
+ u16 i;
+
+ /* Polarity reversal workaround for forced 10F/10H links. */
+
+ /* Disable the transmitter on the PHY */
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
+ if (ret_val)
+ return ret_val;
+
+ /* This loop will early-out if the NO link condition has been met. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Link Status bit
+ * to be clear.
+ */
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if ((mii_status_reg & ~MII_SR_LINK_STATUS) == 0)
+ break;
+ mdelay(100);
+ }
+
+ /* Recommended delay time after link has been lost */
+ mdelay(1000);
+
+ /* Now we will re-enable th transmitter on the PHY */
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
+ if (ret_val)
+ return ret_val;
+ mdelay(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0);
+ if (ret_val)
+ return ret_val;
+ mdelay(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00);
+ if (ret_val)
+ return ret_val;
+ mdelay(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
+ if (ret_val)
+ return ret_val;
+
+ /* This loop will early-out if the link condition has been met. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Link Status bit
+ * to be set.
+ */
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (mii_status_reg & MII_SR_LINK_STATUS)
+ break;
+ mdelay(100);
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_get_auto_rd_done
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Check for EEPROM Auto Read bit done.
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ */
+static s32 e1000_get_auto_rd_done(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_get_auto_rd_done");
+ msleep(5);
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_get_phy_cfg_done
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Checks if the PHY configuration is done
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ */
+static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_get_phy_cfg_done");
+ mdelay(10);
+ return E1000_SUCCESS;
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_hw-2.6.32-orig.h Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,3048 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/* e1000_hw.h
+ * Structures, enums, and macros for the MAC
+ */
+
+#ifndef _E1000_HW_H_
+#define _E1000_HW_H_
+
+#include "e1000_osdep.h"
+
+/* Forward declarations of structures used by the shared code */
+struct e1000_hw;
+struct e1000_hw_stats;
+
+/* Enumerated types specific to the e1000 hardware */
+/* Media Access Controlers */
+typedef enum {
+ e1000_undefined = 0,
+ e1000_82542_rev2_0,
+ e1000_82542_rev2_1,
+ e1000_82543,
+ e1000_82544,
+ e1000_82540,
+ e1000_82545,
+ e1000_82545_rev_3,
+ e1000_82546,
+ e1000_82546_rev_3,
+ e1000_82541,
+ e1000_82541_rev_2,
+ e1000_82547,
+ e1000_82547_rev_2,
+ e1000_num_macs
+} e1000_mac_type;
+
+typedef enum {
+ e1000_eeprom_uninitialized = 0,
+ e1000_eeprom_spi,
+ e1000_eeprom_microwire,
+ e1000_eeprom_flash,
+ e1000_eeprom_none, /* No NVM support */
+ e1000_num_eeprom_types
+} e1000_eeprom_type;
+
+/* Media Types */
+typedef enum {
+ e1000_media_type_copper = 0,
+ e1000_media_type_fiber = 1,
+ e1000_media_type_internal_serdes = 2,
+ e1000_num_media_types
+} e1000_media_type;
+
+typedef enum {
+ e1000_10_half = 0,
+ e1000_10_full = 1,
+ e1000_100_half = 2,
+ e1000_100_full = 3
+} e1000_speed_duplex_type;
+
+/* Flow Control Settings */
+typedef enum {
+ E1000_FC_NONE = 0,
+ E1000_FC_RX_PAUSE = 1,
+ E1000_FC_TX_PAUSE = 2,
+ E1000_FC_FULL = 3,
+ E1000_FC_DEFAULT = 0xFF
+} e1000_fc_type;
+
+struct e1000_shadow_ram {
+ u16 eeprom_word;
+ bool modified;
+};
+
+/* PCI bus types */
+typedef enum {
+ e1000_bus_type_unknown = 0,
+ e1000_bus_type_pci,
+ e1000_bus_type_pcix,
+ e1000_bus_type_reserved
+} e1000_bus_type;
+
+/* PCI bus speeds */
+typedef enum {
+ e1000_bus_speed_unknown = 0,
+ e1000_bus_speed_33,
+ e1000_bus_speed_66,
+ e1000_bus_speed_100,
+ e1000_bus_speed_120,
+ e1000_bus_speed_133,
+ e1000_bus_speed_reserved
+} e1000_bus_speed;
+
+/* PCI bus widths */
+typedef enum {
+ e1000_bus_width_unknown = 0,
+ e1000_bus_width_32,
+ e1000_bus_width_64,
+ e1000_bus_width_reserved
+} e1000_bus_width;
+
+/* PHY status info structure and supporting enums */
+typedef enum {
+ e1000_cable_length_50 = 0,
+ e1000_cable_length_50_80,
+ e1000_cable_length_80_110,
+ e1000_cable_length_110_140,
+ e1000_cable_length_140,
+ e1000_cable_length_undefined = 0xFF
+} e1000_cable_length;
+
+typedef enum {
+ e1000_gg_cable_length_60 = 0,
+ e1000_gg_cable_length_60_115 = 1,
+ e1000_gg_cable_length_115_150 = 2,
+ e1000_gg_cable_length_150 = 4
+} e1000_gg_cable_length;
+
+typedef enum {
+ e1000_igp_cable_length_10 = 10,
+ e1000_igp_cable_length_20 = 20,
+ e1000_igp_cable_length_30 = 30,
+ e1000_igp_cable_length_40 = 40,
+ e1000_igp_cable_length_50 = 50,
+ e1000_igp_cable_length_60 = 60,
+ e1000_igp_cable_length_70 = 70,
+ e1000_igp_cable_length_80 = 80,
+ e1000_igp_cable_length_90 = 90,
+ e1000_igp_cable_length_100 = 100,
+ e1000_igp_cable_length_110 = 110,
+ e1000_igp_cable_length_115 = 115,
+ e1000_igp_cable_length_120 = 120,
+ e1000_igp_cable_length_130 = 130,
+ e1000_igp_cable_length_140 = 140,
+ e1000_igp_cable_length_150 = 150,
+ e1000_igp_cable_length_160 = 160,
+ e1000_igp_cable_length_170 = 170,
+ e1000_igp_cable_length_180 = 180
+} e1000_igp_cable_length;
+
+typedef enum {
+ e1000_10bt_ext_dist_enable_normal = 0,
+ e1000_10bt_ext_dist_enable_lower,
+ e1000_10bt_ext_dist_enable_undefined = 0xFF
+} e1000_10bt_ext_dist_enable;
+
+typedef enum {
+ e1000_rev_polarity_normal = 0,
+ e1000_rev_polarity_reversed,
+ e1000_rev_polarity_undefined = 0xFF
+} e1000_rev_polarity;
+
+typedef enum {
+ e1000_downshift_normal = 0,
+ e1000_downshift_activated,
+ e1000_downshift_undefined = 0xFF
+} e1000_downshift;
+
+typedef enum {
+ e1000_smart_speed_default = 0,
+ e1000_smart_speed_on,
+ e1000_smart_speed_off
+} e1000_smart_speed;
+
+typedef enum {
+ e1000_polarity_reversal_enabled = 0,
+ e1000_polarity_reversal_disabled,
+ e1000_polarity_reversal_undefined = 0xFF
+} e1000_polarity_reversal;
+
+typedef enum {
+ e1000_auto_x_mode_manual_mdi = 0,
+ e1000_auto_x_mode_manual_mdix,
+ e1000_auto_x_mode_auto1,
+ e1000_auto_x_mode_auto2,
+ e1000_auto_x_mode_undefined = 0xFF
+} e1000_auto_x_mode;
+
+typedef enum {
+ e1000_1000t_rx_status_not_ok = 0,
+ e1000_1000t_rx_status_ok,
+ e1000_1000t_rx_status_undefined = 0xFF
+} e1000_1000t_rx_status;
+
+typedef enum {
+ e1000_phy_m88 = 0,
+ e1000_phy_igp,
+ e1000_phy_undefined = 0xFF
+} e1000_phy_type;
+
+typedef enum {
+ e1000_ms_hw_default = 0,
+ e1000_ms_force_master,
+ e1000_ms_force_slave,
+ e1000_ms_auto
+} e1000_ms_type;
+
+typedef enum {
+ e1000_ffe_config_enabled = 0,
+ e1000_ffe_config_active,
+ e1000_ffe_config_blocked
+} e1000_ffe_config;
+
+typedef enum {
+ e1000_dsp_config_disabled = 0,
+ e1000_dsp_config_enabled,
+ e1000_dsp_config_activated,
+ e1000_dsp_config_undefined = 0xFF
+} e1000_dsp_config;
+
+struct e1000_phy_info {
+ e1000_cable_length cable_length;
+ e1000_10bt_ext_dist_enable extended_10bt_distance;
+ e1000_rev_polarity cable_polarity;
+ e1000_downshift downshift;
+ e1000_polarity_reversal polarity_correction;
+ e1000_auto_x_mode mdix_mode;
+ e1000_1000t_rx_status local_rx;
+ e1000_1000t_rx_status remote_rx;
+};
+
+struct e1000_phy_stats {
+ u32 idle_errors;
+ u32 receive_errors;
+};
+
+struct e1000_eeprom_info {
+ e1000_eeprom_type type;
+ u16 word_size;
+ u16 opcode_bits;
+ u16 address_bits;
+ u16 delay_usec;
+ u16 page_size;
+};
+
+/* Flex ASF Information */
+#define E1000_HOST_IF_MAX_SIZE 2048
+
+typedef enum {
+ e1000_byte_align = 0,
+ e1000_word_align = 1,
+ e1000_dword_align = 2
+} e1000_align_type;
+
+/* Error Codes */
+#define E1000_SUCCESS 0
+#define E1000_ERR_EEPROM 1
+#define E1000_ERR_PHY 2
+#define E1000_ERR_CONFIG 3
+#define E1000_ERR_PARAM 4
+#define E1000_ERR_MAC_TYPE 5
+#define E1000_ERR_PHY_TYPE 6
+#define E1000_ERR_RESET 9
+#define E1000_ERR_MASTER_REQUESTS_PENDING 10
+#define E1000_ERR_HOST_INTERFACE_COMMAND 11
+#define E1000_BLK_PHY_RESET 12
+
+#define E1000_BYTE_SWAP_WORD(_value) ((((_value) & 0x00ff) << 8) | \
+ (((_value) & 0xff00) >> 8))
+
+/* Function prototypes */
+/* Initialization */
+s32 e1000_reset_hw(struct e1000_hw *hw);
+s32 e1000_init_hw(struct e1000_hw *hw);
+s32 e1000_set_mac_type(struct e1000_hw *hw);
+void e1000_set_media_type(struct e1000_hw *hw);
+
+/* Link Configuration */
+s32 e1000_setup_link(struct e1000_hw *hw);
+s32 e1000_phy_setup_autoneg(struct e1000_hw *hw);
+void e1000_config_collision_dist(struct e1000_hw *hw);
+s32 e1000_check_for_link(struct e1000_hw *hw);
+s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 * speed, u16 * duplex);
+s32 e1000_force_mac_fc(struct e1000_hw *hw);
+
+/* PHY */
+s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 * phy_data);
+s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 data);
+s32 e1000_phy_hw_reset(struct e1000_hw *hw);
+s32 e1000_phy_reset(struct e1000_hw *hw);
+s32 e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info);
+s32 e1000_validate_mdi_setting(struct e1000_hw *hw);
+
+/* EEPROM Functions */
+s32 e1000_init_eeprom_params(struct e1000_hw *hw);
+
+/* MNG HOST IF functions */
+u32 e1000_enable_mng_pass_thru(struct e1000_hw *hw);
+
+#define E1000_MNG_DHCP_TX_PAYLOAD_CMD 64
+#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8 /* Host Interface data length */
+
+#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10 /* Time in ms to process MNG command */
+#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */
+#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */
+#define E1000_MNG_IAMT_MODE 0x3
+#define E1000_MNG_ICH_IAMT_MODE 0x2
+#define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */
+
+#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */
+#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT 0x2 /* DHCP parsing enabled */
+#define E1000_VFTA_ENTRY_SHIFT 0x5
+#define E1000_VFTA_ENTRY_MASK 0x7F
+#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F
+
+struct e1000_host_mng_command_header {
+ u8 command_id;
+ u8 checksum;
+ u16 reserved1;
+ u16 reserved2;
+ u16 command_length;
+};
+
+struct e1000_host_mng_command_info {
+ struct e1000_host_mng_command_header command_header; /* Command Head/Command Result Head has 4 bytes */
+ u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH]; /* Command data can length 0..0x658 */
+};
+#ifdef __BIG_ENDIAN
+struct e1000_host_mng_dhcp_cookie {
+ u32 signature;
+ u16 vlan_id;
+ u8 reserved0;
+ u8 status;
+ u32 reserved1;
+ u8 checksum;
+ u8 reserved3;
+ u16 reserved2;
+};
+#else
+struct e1000_host_mng_dhcp_cookie {
+ u32 signature;
+ u8 status;
+ u8 reserved0;
+ u16 vlan_id;
+ u32 reserved1;
+ u16 reserved2;
+ u8 reserved3;
+ u8 checksum;
+};
+#endif
+
+bool e1000_check_mng_mode(struct e1000_hw *hw);
+s32 e1000_read_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 * data);
+s32 e1000_validate_eeprom_checksum(struct e1000_hw *hw);
+s32 e1000_update_eeprom_checksum(struct e1000_hw *hw);
+s32 e1000_write_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 * data);
+s32 e1000_read_mac_addr(struct e1000_hw *hw);
+
+/* Filters (multicast, vlan, receive) */
+u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 * mc_addr);
+void e1000_mta_set(struct e1000_hw *hw, u32 hash_value);
+void e1000_rar_set(struct e1000_hw *hw, u8 * mc_addr, u32 rar_index);
+void e1000_write_vfta(struct e1000_hw *hw, u32 offset, u32 value);
+
+/* LED functions */
+s32 e1000_setup_led(struct e1000_hw *hw);
+s32 e1000_cleanup_led(struct e1000_hw *hw);
+s32 e1000_led_on(struct e1000_hw *hw);
+s32 e1000_led_off(struct e1000_hw *hw);
+s32 e1000_blink_led_start(struct e1000_hw *hw);
+
+/* Adaptive IFS Functions */
+
+/* Everything else */
+void e1000_reset_adaptive(struct e1000_hw *hw);
+void e1000_update_adaptive(struct e1000_hw *hw);
+void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats,
+ u32 frame_len, u8 * mac_addr);
+void e1000_get_bus_info(struct e1000_hw *hw);
+void e1000_pci_set_mwi(struct e1000_hw *hw);
+void e1000_pci_clear_mwi(struct e1000_hw *hw);
+void e1000_pcix_set_mmrbc(struct e1000_hw *hw, int mmrbc);
+int e1000_pcix_get_mmrbc(struct e1000_hw *hw);
+/* Port I/O is only supported on 82544 and newer */
+void e1000_io_write(struct e1000_hw *hw, unsigned long port, u32 value);
+
+#define E1000_READ_REG_IO(a, reg) \
+ e1000_read_reg_io((a), E1000_##reg)
+#define E1000_WRITE_REG_IO(a, reg, val) \
+ e1000_write_reg_io((a), E1000_##reg, val)
+
+/* PCI Device IDs */
+#define E1000_DEV_ID_82542 0x1000
+#define E1000_DEV_ID_82543GC_FIBER 0x1001
+#define E1000_DEV_ID_82543GC_COPPER 0x1004
+#define E1000_DEV_ID_82544EI_COPPER 0x1008
+#define E1000_DEV_ID_82544EI_FIBER 0x1009
+#define E1000_DEV_ID_82544GC_COPPER 0x100C
+#define E1000_DEV_ID_82544GC_LOM 0x100D
+#define E1000_DEV_ID_82540EM 0x100E
+#define E1000_DEV_ID_82540EM_LOM 0x1015
+#define E1000_DEV_ID_82540EP_LOM 0x1016
+#define E1000_DEV_ID_82540EP 0x1017
+#define E1000_DEV_ID_82540EP_LP 0x101E
+#define E1000_DEV_ID_82545EM_COPPER 0x100F
+#define E1000_DEV_ID_82545EM_FIBER 0x1011
+#define E1000_DEV_ID_82545GM_COPPER 0x1026
+#define E1000_DEV_ID_82545GM_FIBER 0x1027
+#define E1000_DEV_ID_82545GM_SERDES 0x1028
+#define E1000_DEV_ID_82546EB_COPPER 0x1010
+#define E1000_DEV_ID_82546EB_FIBER 0x1012
+#define E1000_DEV_ID_82546EB_QUAD_COPPER 0x101D
+#define E1000_DEV_ID_82541EI 0x1013
+#define E1000_DEV_ID_82541EI_MOBILE 0x1018
+#define E1000_DEV_ID_82541ER_LOM 0x1014
+#define E1000_DEV_ID_82541ER 0x1078
+#define E1000_DEV_ID_82547GI 0x1075
+#define E1000_DEV_ID_82541GI 0x1076
+#define E1000_DEV_ID_82541GI_MOBILE 0x1077
+#define E1000_DEV_ID_82541GI_LF 0x107C
+#define E1000_DEV_ID_82546GB_COPPER 0x1079
+#define E1000_DEV_ID_82546GB_FIBER 0x107A
+#define E1000_DEV_ID_82546GB_SERDES 0x107B
+#define E1000_DEV_ID_82546GB_PCIE 0x108A
+#define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099
+#define E1000_DEV_ID_82547EI 0x1019
+#define E1000_DEV_ID_82547EI_MOBILE 0x101A
+#define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5
+
+#define NODE_ADDRESS_SIZE 6
+#define ETH_LENGTH_OF_ADDRESS 6
+
+/* MAC decode size is 128K - This is the size of BAR0 */
+#define MAC_DECODE_SIZE (128 * 1024)
+
+#define E1000_82542_2_0_REV_ID 2
+#define E1000_82542_2_1_REV_ID 3
+#define E1000_REVISION_0 0
+#define E1000_REVISION_1 1
+#define E1000_REVISION_2 2
+#define E1000_REVISION_3 3
+
+#define SPEED_10 10
+#define SPEED_100 100
+#define SPEED_1000 1000
+#define HALF_DUPLEX 1
+#define FULL_DUPLEX 2
+
+/* The sizes (in bytes) of a ethernet packet */
+#define ENET_HEADER_SIZE 14
+#define MINIMUM_ETHERNET_FRAME_SIZE 64 /* With FCS */
+#define ETHERNET_FCS_SIZE 4
+#define MINIMUM_ETHERNET_PACKET_SIZE \
+ (MINIMUM_ETHERNET_FRAME_SIZE - ETHERNET_FCS_SIZE)
+#define CRC_LENGTH ETHERNET_FCS_SIZE
+#define MAX_JUMBO_FRAME_SIZE 0x3F00
+
+/* 802.1q VLAN Packet Sizes */
+#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMAed) */
+
+/* Ethertype field values */
+#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */
+#define ETHERNET_IP_TYPE 0x0800 /* IP packets */
+#define ETHERNET_ARP_TYPE 0x0806 /* Address Resolution Protocol (ARP) */
+
+/* Packet Header defines */
+#define IP_PROTOCOL_TCP 6
+#define IP_PROTOCOL_UDP 0x11
+
+/* This defines the bits that are set in the Interrupt Mask
+ * Set/Read Register. Each bit is documented below:
+ * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
+ * o RXSEQ = Receive Sequence Error
+ */
+#define POLL_IMS_ENABLE_MASK ( \
+ E1000_IMS_RXDMT0 | \
+ E1000_IMS_RXSEQ)
+
+/* This defines the bits that are set in the Interrupt Mask
+ * Set/Read Register. Each bit is documented below:
+ * o RXT0 = Receiver Timer Interrupt (ring 0)
+ * o TXDW = Transmit Descriptor Written Back
+ * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
+ * o RXSEQ = Receive Sequence Error
+ * o LSC = Link Status Change
+ */
+#define IMS_ENABLE_MASK ( \
+ E1000_IMS_RXT0 | \
+ E1000_IMS_TXDW | \
+ E1000_IMS_RXDMT0 | \
+ E1000_IMS_RXSEQ | \
+ E1000_IMS_LSC)
+
+/* Number of high/low register pairs in the RAR. The RAR (Receive Address
+ * Registers) holds the directed and multicast addresses that we monitor. We
+ * reserve one of these spots for our directed address, allowing us room for
+ * E1000_RAR_ENTRIES - 1 multicast addresses.
+ */
+#define E1000_RAR_ENTRIES 15
+
+#define MIN_NUMBER_OF_DESCRIPTORS 8
+#define MAX_NUMBER_OF_DESCRIPTORS 0xFFF8
+
+/* Receive Descriptor */
+struct e1000_rx_desc {
+ __le64 buffer_addr; /* Address of the descriptor's data buffer */
+ __le16 length; /* Length of data DMAed into data buffer */
+ __le16 csum; /* Packet checksum */
+ u8 status; /* Descriptor status */
+ u8 errors; /* Descriptor Errors */
+ __le16 special;
+};
+
+/* Receive Descriptor - Extended */
+union e1000_rx_desc_extended {
+ struct {
+ __le64 buffer_addr;
+ __le64 reserved;
+ } read;
+ struct {
+ struct {
+ __le32 mrq; /* Multiple Rx Queues */
+ union {
+ __le32 rss; /* RSS Hash */
+ struct {
+ __le16 ip_id; /* IP id */
+ __le16 csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ __le32 status_error; /* ext status/error */
+ __le16 length;
+ __le16 vlan; /* VLAN tag */
+ } upper;
+ } wb; /* writeback */
+};
+
+#define MAX_PS_BUFFERS 4
+/* Receive Descriptor - Packet Split */
+union e1000_rx_desc_packet_split {
+ struct {
+ /* one buffer for protocol header(s), three data buffers */
+ __le64 buffer_addr[MAX_PS_BUFFERS];
+ } read;
+ struct {
+ struct {
+ __le32 mrq; /* Multiple Rx Queues */
+ union {
+ __le32 rss; /* RSS Hash */
+ struct {
+ __le16 ip_id; /* IP id */
+ __le16 csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ __le32 status_error; /* ext status/error */
+ __le16 length0; /* length of buffer 0 */
+ __le16 vlan; /* VLAN tag */
+ } middle;
+ struct {
+ __le16 header_status;
+ __le16 length[3]; /* length of buffers 1-3 */
+ } upper;
+ __le64 reserved;
+ } wb; /* writeback */
+};
+
+/* Receive Descriptor bit definitions */
+#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
+#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
+#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
+#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
+#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
+#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
+#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */
+#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */
+#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */
+#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */
+#define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */
+#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
+#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
+#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
+#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
+#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */
+#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */
+#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
+#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
+#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */
+#define E1000_RXD_SPC_PRI_SHIFT 13
+#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */
+#define E1000_RXD_SPC_CFI_SHIFT 12
+
+#define E1000_RXDEXT_STATERR_CE 0x01000000
+#define E1000_RXDEXT_STATERR_SE 0x02000000
+#define E1000_RXDEXT_STATERR_SEQ 0x04000000
+#define E1000_RXDEXT_STATERR_CXE 0x10000000
+#define E1000_RXDEXT_STATERR_TCPE 0x20000000
+#define E1000_RXDEXT_STATERR_IPE 0x40000000
+#define E1000_RXDEXT_STATERR_RXE 0x80000000
+
+#define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000
+#define E1000_RXDPS_HDRSTAT_HDRLEN_MASK 0x000003FF
+
+/* mask to determine if packets should be dropped due to frame errors */
+#define E1000_RXD_ERR_FRAME_ERR_MASK ( \
+ E1000_RXD_ERR_CE | \
+ E1000_RXD_ERR_SE | \
+ E1000_RXD_ERR_SEQ | \
+ E1000_RXD_ERR_CXE | \
+ E1000_RXD_ERR_RXE)
+
+/* Same mask, but for extended and packet split descriptors */
+#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
+ E1000_RXDEXT_STATERR_CE | \
+ E1000_RXDEXT_STATERR_SE | \
+ E1000_RXDEXT_STATERR_SEQ | \
+ E1000_RXDEXT_STATERR_CXE | \
+ E1000_RXDEXT_STATERR_RXE)
+
+/* Transmit Descriptor */
+struct e1000_tx_desc {
+ __le64 buffer_addr; /* Address of the descriptor's data buffer */
+ union {
+ __le32 data;
+ struct {
+ __le16 length; /* Data buffer length */
+ u8 cso; /* Checksum offset */
+ u8 cmd; /* Descriptor control */
+ } flags;
+ } lower;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 css; /* Checksum start */
+ __le16 special;
+ } fields;
+ } upper;
+};
+
+/* Transmit Descriptor bit definitions */
+#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */
+#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */
+#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
+#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
+#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
+#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
+#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
+#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
+#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
+#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
+#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
+#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
+#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
+#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
+#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
+#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
+#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
+#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
+#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
+#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
+
+/* Offload Context Descriptor */
+struct e1000_context_desc {
+ union {
+ __le32 ip_config;
+ struct {
+ u8 ipcss; /* IP checksum start */
+ u8 ipcso; /* IP checksum offset */
+ __le16 ipcse; /* IP checksum end */
+ } ip_fields;
+ } lower_setup;
+ union {
+ __le32 tcp_config;
+ struct {
+ u8 tucss; /* TCP checksum start */
+ u8 tucso; /* TCP checksum offset */
+ __le16 tucse; /* TCP checksum end */
+ } tcp_fields;
+ } upper_setup;
+ __le32 cmd_and_length; /* */
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 hdr_len; /* Header length */
+ __le16 mss; /* Maximum segment size */
+ } fields;
+ } tcp_seg_setup;
+};
+
+/* Offload data descriptor */
+struct e1000_data_desc {
+ __le64 buffer_addr; /* Address of the descriptor's buffer address */
+ union {
+ __le32 data;
+ struct {
+ __le16 length; /* Data buffer length */
+ u8 typ_len_ext; /* */
+ u8 cmd; /* */
+ } flags;
+ } lower;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 popts; /* Packet Options */
+ __le16 special; /* */
+ } fields;
+ } upper;
+};
+
+/* Filters */
+#define E1000_NUM_UNICAST 16 /* Unicast filter entries */
+#define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */
+#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
+
+/* Receive Address Register */
+struct e1000_rar {
+ volatile __le32 low; /* receive address low */
+ volatile __le32 high; /* receive address high */
+};
+
+/* Number of entries in the Multicast Table Array (MTA). */
+#define E1000_NUM_MTA_REGISTERS 128
+
+/* IPv4 Address Table Entry */
+struct e1000_ipv4_at_entry {
+ volatile u32 ipv4_addr; /* IP Address (RW) */
+ volatile u32 reserved;
+};
+
+/* Four wakeup IP addresses are supported */
+#define E1000_WAKEUP_IP_ADDRESS_COUNT_MAX 4
+#define E1000_IP4AT_SIZE E1000_WAKEUP_IP_ADDRESS_COUNT_MAX
+#define E1000_IP6AT_SIZE 1
+
+/* IPv6 Address Table Entry */
+struct e1000_ipv6_at_entry {
+ volatile u8 ipv6_addr[16];
+};
+
+/* Flexible Filter Length Table Entry */
+struct e1000_fflt_entry {
+ volatile u32 length; /* Flexible Filter Length (RW) */
+ volatile u32 reserved;
+};
+
+/* Flexible Filter Mask Table Entry */
+struct e1000_ffmt_entry {
+ volatile u32 mask; /* Flexible Filter Mask (RW) */
+ volatile u32 reserved;
+};
+
+/* Flexible Filter Value Table Entry */
+struct e1000_ffvt_entry {
+ volatile u32 value; /* Flexible Filter Value (RW) */
+ volatile u32 reserved;
+};
+
+/* Four Flexible Filters are supported */
+#define E1000_FLEXIBLE_FILTER_COUNT_MAX 4
+
+/* Each Flexible Filter is at most 128 (0x80) bytes in length */
+#define E1000_FLEXIBLE_FILTER_SIZE_MAX 128
+
+#define E1000_FFLT_SIZE E1000_FLEXIBLE_FILTER_COUNT_MAX
+#define E1000_FFMT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX
+#define E1000_FFVT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX
+
+#define E1000_DISABLE_SERDES_LOOPBACK 0x0400
+
+/* Register Set. (82543, 82544)
+ *
+ * Registers are defined to be 32 bits and should be accessed as 32 bit values.
+ * These registers are physically located on the NIC, but are mapped into the
+ * host memory address space.
+ *
+ * RW - register is both readable and writable
+ * RO - register is read only
+ * WO - register is write only
+ * R/clr - register is read only and is cleared when read
+ * A - register array
+ */
+#define E1000_CTRL 0x00000 /* Device Control - RW */
+#define E1000_CTRL_DUP 0x00004 /* Device Control Duplicate (Shadow) - RW */
+#define E1000_STATUS 0x00008 /* Device Status - RO */
+#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */
+#define E1000_EERD 0x00014 /* EEPROM Read - RW */
+#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */
+#define E1000_FLA 0x0001C /* Flash Access - RW */
+#define E1000_MDIC 0x00020 /* MDI Control - RW */
+#define E1000_SCTL 0x00024 /* SerDes Control - RW */
+#define E1000_FEXTNVM 0x00028 /* Future Extended NVM register */
+#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */
+#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */
+#define E1000_FCT 0x00030 /* Flow Control Type - RW */
+#define E1000_VET 0x00038 /* VLAN Ether Type - RW */
+#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */
+#define E1000_ITR 0x000C4 /* Interrupt Throttling Rate - RW */
+#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */
+#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */
+#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */
+#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */
+#define E1000_RCTL 0x00100 /* RX Control - RW */
+#define E1000_RDTR1 0x02820 /* RX Delay Timer (1) - RW */
+#define E1000_RDBAL1 0x02900 /* RX Descriptor Base Address Low (1) - RW */
+#define E1000_RDBAH1 0x02904 /* RX Descriptor Base Address High (1) - RW */
+#define E1000_RDLEN1 0x02908 /* RX Descriptor Length (1) - RW */
+#define E1000_RDH1 0x02910 /* RX Descriptor Head (1) - RW */
+#define E1000_RDT1 0x02918 /* RX Descriptor Tail (1) - RW */
+#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */
+#define E1000_TXCW 0x00178 /* TX Configuration Word - RW */
+#define E1000_RXCW 0x00180 /* RX Configuration Word - RO */
+#define E1000_TCTL 0x00400 /* TX Control - RW */
+#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */
+#define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */
+#define E1000_TBT 0x00448 /* TX Burst Timer - RW */
+#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */
+#define E1000_LEDCTL 0x00E00 /* LED Control - RW */
+#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */
+#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */
+#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */
+#define FEXTNVM_SW_CONFIG 0x0001
+#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
+#define E1000_PBS 0x01008 /* Packet Buffer Size */
+#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
+#define E1000_FLASH_UPDATES 1000
+#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */
+#define E1000_FLASHT 0x01028 /* FLASH Timer Register */
+#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */
+#define E1000_FLSWCTL 0x01030 /* FLASH control register */
+#define E1000_FLSWDATA 0x01034 /* FLASH data register */
+#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */
+#define E1000_FLOP 0x0103C /* FLASH Opcode Register */
+#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */
+#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */
+#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */
+#define E1000_PSRCTL 0x02170 /* Packet Split Receive Control - RW */
+#define E1000_RDBAL 0x02800 /* RX Descriptor Base Address Low - RW */
+#define E1000_RDBAH 0x02804 /* RX Descriptor Base Address High - RW */
+#define E1000_RDLEN 0x02808 /* RX Descriptor Length - RW */
+#define E1000_RDH 0x02810 /* RX Descriptor Head - RW */
+#define E1000_RDT 0x02818 /* RX Descriptor Tail - RW */
+#define E1000_RDTR 0x02820 /* RX Delay Timer - RW */
+#define E1000_RDBAL0 E1000_RDBAL /* RX Desc Base Address Low (0) - RW */
+#define E1000_RDBAH0 E1000_RDBAH /* RX Desc Base Address High (0) - RW */
+#define E1000_RDLEN0 E1000_RDLEN /* RX Desc Length (0) - RW */
+#define E1000_RDH0 E1000_RDH /* RX Desc Head (0) - RW */
+#define E1000_RDT0 E1000_RDT /* RX Desc Tail (0) - RW */
+#define E1000_RDTR0 E1000_RDTR /* RX Delay Timer (0) - RW */
+#define E1000_RXDCTL 0x02828 /* RX Descriptor Control queue 0 - RW */
+#define E1000_RXDCTL1 0x02928 /* RX Descriptor Control queue 1 - RW */
+#define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */
+#define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */
+#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */
+#define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */
+#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */
+#define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */
+#define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */
+#define E1000_TDFHS 0x03420 /* TX Data FIFO Head Saved - RW */
+#define E1000_TDFTS 0x03428 /* TX Data FIFO Tail Saved - RW */
+#define E1000_TDFPC 0x03430 /* TX Data FIFO Packet Count - RW */
+#define E1000_TDBAL 0x03800 /* TX Descriptor Base Address Low - RW */
+#define E1000_TDBAH 0x03804 /* TX Descriptor Base Address High - RW */
+#define E1000_TDLEN 0x03808 /* TX Descriptor Length - RW */
+#define E1000_TDH 0x03810 /* TX Descriptor Head - RW */
+#define E1000_TDT 0x03818 /* TX Descripotr Tail - RW */
+#define E1000_TIDV 0x03820 /* TX Interrupt Delay Value - RW */
+#define E1000_TXDCTL 0x03828 /* TX Descriptor Control - RW */
+#define E1000_TADV 0x0382C /* TX Interrupt Absolute Delay Val - RW */
+#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */
+#define E1000_TARC0 0x03840 /* TX Arbitration Count (0) */
+#define E1000_TDBAL1 0x03900 /* TX Desc Base Address Low (1) - RW */
+#define E1000_TDBAH1 0x03904 /* TX Desc Base Address High (1) - RW */
+#define E1000_TDLEN1 0x03908 /* TX Desc Length (1) - RW */
+#define E1000_TDH1 0x03910 /* TX Desc Head (1) - RW */
+#define E1000_TDT1 0x03918 /* TX Desc Tail (1) - RW */
+#define E1000_TXDCTL1 0x03928 /* TX Descriptor Control (1) - RW */
+#define E1000_TARC1 0x03940 /* TX Arbitration Count (1) */
+#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */
+#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */
+#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */
+#define E1000_RXERRC 0x0400C /* Receive Error Count - R/clr */
+#define E1000_MPC 0x04010 /* Missed Packet Count - R/clr */
+#define E1000_SCC 0x04014 /* Single Collision Count - R/clr */
+#define E1000_ECOL 0x04018 /* Excessive Collision Count - R/clr */
+#define E1000_MCC 0x0401C /* Multiple Collision Count - R/clr */
+#define E1000_LATECOL 0x04020 /* Late Collision Count - R/clr */
+#define E1000_COLC 0x04028 /* Collision Count - R/clr */
+#define E1000_DC 0x04030 /* Defer Count - R/clr */
+#define E1000_TNCRS 0x04034 /* TX-No CRS - R/clr */
+#define E1000_SEC 0x04038 /* Sequence Error Count - R/clr */
+#define E1000_CEXTERR 0x0403C /* Carrier Extension Error Count - R/clr */
+#define E1000_RLEC 0x04040 /* Receive Length Error Count - R/clr */
+#define E1000_XONRXC 0x04048 /* XON RX Count - R/clr */
+#define E1000_XONTXC 0x0404C /* XON TX Count - R/clr */
+#define E1000_XOFFRXC 0x04050 /* XOFF RX Count - R/clr */
+#define E1000_XOFFTXC 0x04054 /* XOFF TX Count - R/clr */
+#define E1000_FCRUC 0x04058 /* Flow Control RX Unsupported Count- R/clr */
+#define E1000_PRC64 0x0405C /* Packets RX (64 bytes) - R/clr */
+#define E1000_PRC127 0x04060 /* Packets RX (65-127 bytes) - R/clr */
+#define E1000_PRC255 0x04064 /* Packets RX (128-255 bytes) - R/clr */
+#define E1000_PRC511 0x04068 /* Packets RX (255-511 bytes) - R/clr */
+#define E1000_PRC1023 0x0406C /* Packets RX (512-1023 bytes) - R/clr */
+#define E1000_PRC1522 0x04070 /* Packets RX (1024-1522 bytes) - R/clr */
+#define E1000_GPRC 0x04074 /* Good Packets RX Count - R/clr */
+#define E1000_BPRC 0x04078 /* Broadcast Packets RX Count - R/clr */
+#define E1000_MPRC 0x0407C /* Multicast Packets RX Count - R/clr */
+#define E1000_GPTC 0x04080 /* Good Packets TX Count - R/clr */
+#define E1000_GORCL 0x04088 /* Good Octets RX Count Low - R/clr */
+#define E1000_GORCH 0x0408C /* Good Octets RX Count High - R/clr */
+#define E1000_GOTCL 0x04090 /* Good Octets TX Count Low - R/clr */
+#define E1000_GOTCH 0x04094 /* Good Octets TX Count High - R/clr */
+#define E1000_RNBC 0x040A0 /* RX No Buffers Count - R/clr */
+#define E1000_RUC 0x040A4 /* RX Undersize Count - R/clr */
+#define E1000_RFC 0x040A8 /* RX Fragment Count - R/clr */
+#define E1000_ROC 0x040AC /* RX Oversize Count - R/clr */
+#define E1000_RJC 0x040B0 /* RX Jabber Count - R/clr */
+#define E1000_MGTPRC 0x040B4 /* Management Packets RX Count - R/clr */
+#define E1000_MGTPDC 0x040B8 /* Management Packets Dropped Count - R/clr */
+#define E1000_MGTPTC 0x040BC /* Management Packets TX Count - R/clr */
+#define E1000_TORL 0x040C0 /* Total Octets RX Low - R/clr */
+#define E1000_TORH 0x040C4 /* Total Octets RX High - R/clr */
+#define E1000_TOTL 0x040C8 /* Total Octets TX Low - R/clr */
+#define E1000_TOTH 0x040CC /* Total Octets TX High - R/clr */
+#define E1000_TPR 0x040D0 /* Total Packets RX - R/clr */
+#define E1000_TPT 0x040D4 /* Total Packets TX - R/clr */
+#define E1000_PTC64 0x040D8 /* Packets TX (64 bytes) - R/clr */
+#define E1000_PTC127 0x040DC /* Packets TX (65-127 bytes) - R/clr */
+#define E1000_PTC255 0x040E0 /* Packets TX (128-255 bytes) - R/clr */
+#define E1000_PTC511 0x040E4 /* Packets TX (256-511 bytes) - R/clr */
+#define E1000_PTC1023 0x040E8 /* Packets TX (512-1023 bytes) - R/clr */
+#define E1000_PTC1522 0x040EC /* Packets TX (1024-1522 Bytes) - R/clr */
+#define E1000_MPTC 0x040F0 /* Multicast Packets TX Count - R/clr */
+#define E1000_BPTC 0x040F4 /* Broadcast Packets TX Count - R/clr */
+#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context TX - R/clr */
+#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context TX Fail - R/clr */
+#define E1000_IAC 0x04100 /* Interrupt Assertion Count */
+#define E1000_ICRXPTC 0x04104 /* Interrupt Cause Rx Packet Timer Expire Count */
+#define E1000_ICRXATC 0x04108 /* Interrupt Cause Rx Absolute Timer Expire Count */
+#define E1000_ICTXPTC 0x0410C /* Interrupt Cause Tx Packet Timer Expire Count */
+#define E1000_ICTXATC 0x04110 /* Interrupt Cause Tx Absolute Timer Expire Count */
+#define E1000_ICTXQEC 0x04118 /* Interrupt Cause Tx Queue Empty Count */
+#define E1000_ICTXQMTC 0x0411C /* Interrupt Cause Tx Queue Minimum Threshold Count */
+#define E1000_ICRXDMTC 0x04120 /* Interrupt Cause Rx Descriptor Minimum Threshold Count */
+#define E1000_ICRXOC 0x04124 /* Interrupt Cause Receiver Overrun Count */
+#define E1000_RXCSUM 0x05000 /* RX Checksum Control - RW */
+#define E1000_RFCTL 0x05008 /* Receive Filter Control */
+#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */
+#define E1000_RA 0x05400 /* Receive Address - RW Array */
+#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */
+#define E1000_WUC 0x05800 /* Wakeup Control - RW */
+#define E1000_WUFC 0x05808 /* Wakeup Filter Control - RW */
+#define E1000_WUS 0x05810 /* Wakeup Status - RO */
+#define E1000_MANC 0x05820 /* Management Control - RW */
+#define E1000_IPAV 0x05838 /* IP Address Valid - RW */
+#define E1000_IP4AT 0x05840 /* IPv4 Address Table - RW Array */
+#define E1000_IP6AT 0x05880 /* IPv6 Address Table - RW Array */
+#define E1000_WUPL 0x05900 /* Wakeup Packet Length - RW */
+#define E1000_WUPM 0x05A00 /* Wakeup Packet Memory - RO A */
+#define E1000_FFLT 0x05F00 /* Flexible Filter Length Table - RW Array */
+#define E1000_HOST_IF 0x08800 /* Host Interface */
+#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */
+#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */
+
+#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */
+#define E1000_MDPHYA 0x0003C /* PHY address - RW */
+#define E1000_MANC2H 0x05860 /* Managment Control To Host - RW */
+#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */
+
+#define E1000_GCR 0x05B00 /* PCI-Ex Control */
+#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */
+#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */
+#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */
+#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */
+#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */
+#define E1000_SWSM 0x05B50 /* SW Semaphore */
+#define E1000_FWSM 0x05B54 /* FW Semaphore */
+#define E1000_FFLT_DBG 0x05F04 /* Debug Register */
+#define E1000_HICR 0x08F00 /* Host Interface Control */
+
+/* RSS registers */
+#define E1000_CPUVEC 0x02C10 /* CPU Vector Register - RW */
+#define E1000_MRQC 0x05818 /* Multiple Receive Control - RW */
+#define E1000_RETA 0x05C00 /* Redirection Table - RW Array */
+#define E1000_RSSRK 0x05C80 /* RSS Random Key - RW Array */
+#define E1000_RSSIM 0x05864 /* RSS Interrupt Mask */
+#define E1000_RSSIR 0x05868 /* RSS Interrupt Request */
+/* Register Set (82542)
+ *
+ * Some of the 82542 registers are located at different offsets than they are
+ * in more current versions of the 8254x. Despite the difference in location,
+ * the registers function in the same manner.
+ */
+#define E1000_82542_CTRL E1000_CTRL
+#define E1000_82542_CTRL_DUP E1000_CTRL_DUP
+#define E1000_82542_STATUS E1000_STATUS
+#define E1000_82542_EECD E1000_EECD
+#define E1000_82542_EERD E1000_EERD
+#define E1000_82542_CTRL_EXT E1000_CTRL_EXT
+#define E1000_82542_FLA E1000_FLA
+#define E1000_82542_MDIC E1000_MDIC
+#define E1000_82542_SCTL E1000_SCTL
+#define E1000_82542_FEXTNVM E1000_FEXTNVM
+#define E1000_82542_FCAL E1000_FCAL
+#define E1000_82542_FCAH E1000_FCAH
+#define E1000_82542_FCT E1000_FCT
+#define E1000_82542_VET E1000_VET
+#define E1000_82542_RA 0x00040
+#define E1000_82542_ICR E1000_ICR
+#define E1000_82542_ITR E1000_ITR
+#define E1000_82542_ICS E1000_ICS
+#define E1000_82542_IMS E1000_IMS
+#define E1000_82542_IMC E1000_IMC
+#define E1000_82542_RCTL E1000_RCTL
+#define E1000_82542_RDTR 0x00108
+#define E1000_82542_RDBAL 0x00110
+#define E1000_82542_RDBAH 0x00114
+#define E1000_82542_RDLEN 0x00118
+#define E1000_82542_RDH 0x00120
+#define E1000_82542_RDT 0x00128
+#define E1000_82542_RDTR0 E1000_82542_RDTR
+#define E1000_82542_RDBAL0 E1000_82542_RDBAL
+#define E1000_82542_RDBAH0 E1000_82542_RDBAH
+#define E1000_82542_RDLEN0 E1000_82542_RDLEN
+#define E1000_82542_RDH0 E1000_82542_RDH
+#define E1000_82542_RDT0 E1000_82542_RDT
+#define E1000_82542_SRRCTL(_n) (0x280C + ((_n) << 8)) /* Split and Replication
+ * RX Control - RW */
+#define E1000_82542_DCA_RXCTRL(_n) (0x02814 + ((_n) << 8))
+#define E1000_82542_RDBAH3 0x02B04 /* RX Desc Base High Queue 3 - RW */
+#define E1000_82542_RDBAL3 0x02B00 /* RX Desc Low Queue 3 - RW */
+#define E1000_82542_RDLEN3 0x02B08 /* RX Desc Length Queue 3 - RW */
+#define E1000_82542_RDH3 0x02B10 /* RX Desc Head Queue 3 - RW */
+#define E1000_82542_RDT3 0x02B18 /* RX Desc Tail Queue 3 - RW */
+#define E1000_82542_RDBAL2 0x02A00 /* RX Desc Base Low Queue 2 - RW */
+#define E1000_82542_RDBAH2 0x02A04 /* RX Desc Base High Queue 2 - RW */
+#define E1000_82542_RDLEN2 0x02A08 /* RX Desc Length Queue 2 - RW */
+#define E1000_82542_RDH2 0x02A10 /* RX Desc Head Queue 2 - RW */
+#define E1000_82542_RDT2 0x02A18 /* RX Desc Tail Queue 2 - RW */
+#define E1000_82542_RDTR1 0x00130
+#define E1000_82542_RDBAL1 0x00138
+#define E1000_82542_RDBAH1 0x0013C
+#define E1000_82542_RDLEN1 0x00140
+#define E1000_82542_RDH1 0x00148
+#define E1000_82542_RDT1 0x00150
+#define E1000_82542_FCRTH 0x00160
+#define E1000_82542_FCRTL 0x00168
+#define E1000_82542_FCTTV E1000_FCTTV
+#define E1000_82542_TXCW E1000_TXCW
+#define E1000_82542_RXCW E1000_RXCW
+#define E1000_82542_MTA 0x00200
+#define E1000_82542_TCTL E1000_TCTL
+#define E1000_82542_TCTL_EXT E1000_TCTL_EXT
+#define E1000_82542_TIPG E1000_TIPG
+#define E1000_82542_TDBAL 0x00420
+#define E1000_82542_TDBAH 0x00424
+#define E1000_82542_TDLEN 0x00428
+#define E1000_82542_TDH 0x00430
+#define E1000_82542_TDT 0x00438
+#define E1000_82542_TIDV 0x00440
+#define E1000_82542_TBT E1000_TBT
+#define E1000_82542_AIT E1000_AIT
+#define E1000_82542_VFTA 0x00600
+#define E1000_82542_LEDCTL E1000_LEDCTL
+#define E1000_82542_PBA E1000_PBA
+#define E1000_82542_PBS E1000_PBS
+#define E1000_82542_EEMNGCTL E1000_EEMNGCTL
+#define E1000_82542_EEARBC E1000_EEARBC
+#define E1000_82542_FLASHT E1000_FLASHT
+#define E1000_82542_EEWR E1000_EEWR
+#define E1000_82542_FLSWCTL E1000_FLSWCTL
+#define E1000_82542_FLSWDATA E1000_FLSWDATA
+#define E1000_82542_FLSWCNT E1000_FLSWCNT
+#define E1000_82542_FLOP E1000_FLOP
+#define E1000_82542_EXTCNF_CTRL E1000_EXTCNF_CTRL
+#define E1000_82542_EXTCNF_SIZE E1000_EXTCNF_SIZE
+#define E1000_82542_PHY_CTRL E1000_PHY_CTRL
+#define E1000_82542_ERT E1000_ERT
+#define E1000_82542_RXDCTL E1000_RXDCTL
+#define E1000_82542_RXDCTL1 E1000_RXDCTL1
+#define E1000_82542_RADV E1000_RADV
+#define E1000_82542_RSRPD E1000_RSRPD
+#define E1000_82542_TXDMAC E1000_TXDMAC
+#define E1000_82542_KABGTXD E1000_KABGTXD
+#define E1000_82542_TDFHS E1000_TDFHS
+#define E1000_82542_TDFTS E1000_TDFTS
+#define E1000_82542_TDFPC E1000_TDFPC
+#define E1000_82542_TXDCTL E1000_TXDCTL
+#define E1000_82542_TADV E1000_TADV
+#define E1000_82542_TSPMT E1000_TSPMT
+#define E1000_82542_CRCERRS E1000_CRCERRS
+#define E1000_82542_ALGNERRC E1000_ALGNERRC
+#define E1000_82542_SYMERRS E1000_SYMERRS
+#define E1000_82542_RXERRC E1000_RXERRC
+#define E1000_82542_MPC E1000_MPC
+#define E1000_82542_SCC E1000_SCC
+#define E1000_82542_ECOL E1000_ECOL
+#define E1000_82542_MCC E1000_MCC
+#define E1000_82542_LATECOL E1000_LATECOL
+#define E1000_82542_COLC E1000_COLC
+#define E1000_82542_DC E1000_DC
+#define E1000_82542_TNCRS E1000_TNCRS
+#define E1000_82542_SEC E1000_SEC
+#define E1000_82542_CEXTERR E1000_CEXTERR
+#define E1000_82542_RLEC E1000_RLEC
+#define E1000_82542_XONRXC E1000_XONRXC
+#define E1000_82542_XONTXC E1000_XONTXC
+#define E1000_82542_XOFFRXC E1000_XOFFRXC
+#define E1000_82542_XOFFTXC E1000_XOFFTXC
+#define E1000_82542_FCRUC E1000_FCRUC
+#define E1000_82542_PRC64 E1000_PRC64
+#define E1000_82542_PRC127 E1000_PRC127
+#define E1000_82542_PRC255 E1000_PRC255
+#define E1000_82542_PRC511 E1000_PRC511
+#define E1000_82542_PRC1023 E1000_PRC1023
+#define E1000_82542_PRC1522 E1000_PRC1522
+#define E1000_82542_GPRC E1000_GPRC
+#define E1000_82542_BPRC E1000_BPRC
+#define E1000_82542_MPRC E1000_MPRC
+#define E1000_82542_GPTC E1000_GPTC
+#define E1000_82542_GORCL E1000_GORCL
+#define E1000_82542_GORCH E1000_GORCH
+#define E1000_82542_GOTCL E1000_GOTCL
+#define E1000_82542_GOTCH E1000_GOTCH
+#define E1000_82542_RNBC E1000_RNBC
+#define E1000_82542_RUC E1000_RUC
+#define E1000_82542_RFC E1000_RFC
+#define E1000_82542_ROC E1000_ROC
+#define E1000_82542_RJC E1000_RJC
+#define E1000_82542_MGTPRC E1000_MGTPRC
+#define E1000_82542_MGTPDC E1000_MGTPDC
+#define E1000_82542_MGTPTC E1000_MGTPTC
+#define E1000_82542_TORL E1000_TORL
+#define E1000_82542_TORH E1000_TORH
+#define E1000_82542_TOTL E1000_TOTL
+#define E1000_82542_TOTH E1000_TOTH
+#define E1000_82542_TPR E1000_TPR
+#define E1000_82542_TPT E1000_TPT
+#define E1000_82542_PTC64 E1000_PTC64
+#define E1000_82542_PTC127 E1000_PTC127
+#define E1000_82542_PTC255 E1000_PTC255
+#define E1000_82542_PTC511 E1000_PTC511
+#define E1000_82542_PTC1023 E1000_PTC1023
+#define E1000_82542_PTC1522 E1000_PTC1522
+#define E1000_82542_MPTC E1000_MPTC
+#define E1000_82542_BPTC E1000_BPTC
+#define E1000_82542_TSCTC E1000_TSCTC
+#define E1000_82542_TSCTFC E1000_TSCTFC
+#define E1000_82542_RXCSUM E1000_RXCSUM
+#define E1000_82542_WUC E1000_WUC
+#define E1000_82542_WUFC E1000_WUFC
+#define E1000_82542_WUS E1000_WUS
+#define E1000_82542_MANC E1000_MANC
+#define E1000_82542_IPAV E1000_IPAV
+#define E1000_82542_IP4AT E1000_IP4AT
+#define E1000_82542_IP6AT E1000_IP6AT
+#define E1000_82542_WUPL E1000_WUPL
+#define E1000_82542_WUPM E1000_WUPM
+#define E1000_82542_FFLT E1000_FFLT
+#define E1000_82542_TDFH 0x08010
+#define E1000_82542_TDFT 0x08018
+#define E1000_82542_FFMT E1000_FFMT
+#define E1000_82542_FFVT E1000_FFVT
+#define E1000_82542_HOST_IF E1000_HOST_IF
+#define E1000_82542_IAM E1000_IAM
+#define E1000_82542_EEMNGCTL E1000_EEMNGCTL
+#define E1000_82542_PSRCTL E1000_PSRCTL
+#define E1000_82542_RAID E1000_RAID
+#define E1000_82542_TARC0 E1000_TARC0
+#define E1000_82542_TDBAL1 E1000_TDBAL1
+#define E1000_82542_TDBAH1 E1000_TDBAH1
+#define E1000_82542_TDLEN1 E1000_TDLEN1
+#define E1000_82542_TDH1 E1000_TDH1
+#define E1000_82542_TDT1 E1000_TDT1
+#define E1000_82542_TXDCTL1 E1000_TXDCTL1
+#define E1000_82542_TARC1 E1000_TARC1
+#define E1000_82542_RFCTL E1000_RFCTL
+#define E1000_82542_GCR E1000_GCR
+#define E1000_82542_GSCL_1 E1000_GSCL_1
+#define E1000_82542_GSCL_2 E1000_GSCL_2
+#define E1000_82542_GSCL_3 E1000_GSCL_3
+#define E1000_82542_GSCL_4 E1000_GSCL_4
+#define E1000_82542_FACTPS E1000_FACTPS
+#define E1000_82542_SWSM E1000_SWSM
+#define E1000_82542_FWSM E1000_FWSM
+#define E1000_82542_FFLT_DBG E1000_FFLT_DBG
+#define E1000_82542_IAC E1000_IAC
+#define E1000_82542_ICRXPTC E1000_ICRXPTC
+#define E1000_82542_ICRXATC E1000_ICRXATC
+#define E1000_82542_ICTXPTC E1000_ICTXPTC
+#define E1000_82542_ICTXATC E1000_ICTXATC
+#define E1000_82542_ICTXQEC E1000_ICTXQEC
+#define E1000_82542_ICTXQMTC E1000_ICTXQMTC
+#define E1000_82542_ICRXDMTC E1000_ICRXDMTC
+#define E1000_82542_ICRXOC E1000_ICRXOC
+#define E1000_82542_HICR E1000_HICR
+
+#define E1000_82542_CPUVEC E1000_CPUVEC
+#define E1000_82542_MRQC E1000_MRQC
+#define E1000_82542_RETA E1000_RETA
+#define E1000_82542_RSSRK E1000_RSSRK
+#define E1000_82542_RSSIM E1000_RSSIM
+#define E1000_82542_RSSIR E1000_RSSIR
+#define E1000_82542_KUMCTRLSTA E1000_KUMCTRLSTA
+#define E1000_82542_SW_FW_SYNC E1000_SW_FW_SYNC
+
+/* Statistics counters collected by the MAC */
+struct e1000_hw_stats {
+ u64 crcerrs;
+ u64 algnerrc;
+ u64 symerrs;
+ u64 rxerrc;
+ u64 txerrc;
+ u64 mpc;
+ u64 scc;
+ u64 ecol;
+ u64 mcc;
+ u64 latecol;
+ u64 colc;
+ u64 dc;
+ u64 tncrs;
+ u64 sec;
+ u64 cexterr;
+ u64 rlec;
+ u64 xonrxc;
+ u64 xontxc;
+ u64 xoffrxc;
+ u64 xofftxc;
+ u64 fcruc;
+ u64 prc64;
+ u64 prc127;
+ u64 prc255;
+ u64 prc511;
+ u64 prc1023;
+ u64 prc1522;
+ u64 gprc;
+ u64 bprc;
+ u64 mprc;
+ u64 gptc;
+ u64 gorcl;
+ u64 gorch;
+ u64 gotcl;
+ u64 gotch;
+ u64 rnbc;
+ u64 ruc;
+ u64 rfc;
+ u64 roc;
+ u64 rlerrc;
+ u64 rjc;
+ u64 mgprc;
+ u64 mgpdc;
+ u64 mgptc;
+ u64 torl;
+ u64 torh;
+ u64 totl;
+ u64 toth;
+ u64 tpr;
+ u64 tpt;
+ u64 ptc64;
+ u64 ptc127;
+ u64 ptc255;
+ u64 ptc511;
+ u64 ptc1023;
+ u64 ptc1522;
+ u64 mptc;
+ u64 bptc;
+ u64 tsctc;
+ u64 tsctfc;
+ u64 iac;
+ u64 icrxptc;
+ u64 icrxatc;
+ u64 ictxptc;
+ u64 ictxatc;
+ u64 ictxqec;
+ u64 ictxqmtc;
+ u64 icrxdmtc;
+ u64 icrxoc;
+};
+
+/* Structure containing variables used by the shared code (e1000_hw.c) */
+struct e1000_hw {
+ u8 __iomem *hw_addr;
+ u8 __iomem *flash_address;
+ e1000_mac_type mac_type;
+ e1000_phy_type phy_type;
+ u32 phy_init_script;
+ e1000_media_type media_type;
+ void *back;
+ struct e1000_shadow_ram *eeprom_shadow_ram;
+ u32 flash_bank_size;
+ u32 flash_base_addr;
+ e1000_fc_type fc;
+ e1000_bus_speed bus_speed;
+ e1000_bus_width bus_width;
+ e1000_bus_type bus_type;
+ struct e1000_eeprom_info eeprom;
+ e1000_ms_type master_slave;
+ e1000_ms_type original_master_slave;
+ e1000_ffe_config ffe_config_state;
+ u32 asf_firmware_present;
+ u32 eeprom_semaphore_present;
+ unsigned long io_base;
+ u32 phy_id;
+ u32 phy_revision;
+ u32 phy_addr;
+ u32 original_fc;
+ u32 txcw;
+ u32 autoneg_failed;
+ u32 max_frame_size;
+ u32 min_frame_size;
+ u32 mc_filter_type;
+ u32 num_mc_addrs;
+ u32 collision_delta;
+ u32 tx_packet_delta;
+ u32 ledctl_default;
+ u32 ledctl_mode1;
+ u32 ledctl_mode2;
+ bool tx_pkt_filtering;
+ struct e1000_host_mng_dhcp_cookie mng_cookie;
+ u16 phy_spd_default;
+ u16 autoneg_advertised;
+ u16 pci_cmd_word;
+ u16 fc_high_water;
+ u16 fc_low_water;
+ u16 fc_pause_time;
+ u16 current_ifs_val;
+ u16 ifs_min_val;
+ u16 ifs_max_val;
+ u16 ifs_step_size;
+ u16 ifs_ratio;
+ u16 device_id;
+ u16 vendor_id;
+ u16 subsystem_id;
+ u16 subsystem_vendor_id;
+ u8 revision_id;
+ u8 autoneg;
+ u8 mdix;
+ u8 forced_speed_duplex;
+ u8 wait_autoneg_complete;
+ u8 dma_fairness;
+ u8 mac_addr[NODE_ADDRESS_SIZE];
+ u8 perm_mac_addr[NODE_ADDRESS_SIZE];
+ bool disable_polarity_correction;
+ bool speed_downgraded;
+ e1000_smart_speed smart_speed;
+ e1000_dsp_config dsp_config_state;
+ bool get_link_status;
+ bool serdes_has_link;
+ bool tbi_compatibility_en;
+ bool tbi_compatibility_on;
+ bool laa_is_present;
+ bool phy_reset_disable;
+ bool initialize_hw_bits_disable;
+ bool fc_send_xon;
+ bool fc_strict_ieee;
+ bool report_tx_early;
+ bool adaptive_ifs;
+ bool ifs_params_forced;
+ bool in_ifs_mode;
+ bool mng_reg_access_disabled;
+ bool leave_av_bit_off;
+ bool bad_tx_carr_stats_fd;
+ bool has_smbus;
+};
+
+#define E1000_EEPROM_SWDPIN0 0x0001 /* SWDPIN 0 EEPROM Value */
+#define E1000_EEPROM_LED_LOGIC 0x0020 /* Led Logic Word */
+#define E1000_EEPROM_RW_REG_DATA 16 /* Offset to data in EEPROM read/write registers */
+#define E1000_EEPROM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
+#define E1000_EEPROM_RW_REG_START 1 /* First bit for telling part to start operation */
+#define E1000_EEPROM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
+#define E1000_EEPROM_POLL_WRITE 1 /* Flag for polling for write complete */
+#define E1000_EEPROM_POLL_READ 0 /* Flag for polling for read complete */
+/* Register Bit Masks */
+/* Device Control */
+#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
+#define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */
+#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */
+#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
+#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
+#define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */
+#define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */
+#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
+#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
+#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
+#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
+#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */
+#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
+#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
+#define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */
+#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
+#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
+#define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */
+#define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock indication in SDP[0] */
+#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through PHYRST_N pin */
+#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external LINK_0 and LINK_1 pins */
+#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
+#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
+#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */
+#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */
+#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
+#define E1000_CTRL_SWDPIO1 0x00800000 /* SWDPIN 1 input or output */
+#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */
+#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */
+#define E1000_CTRL_RST 0x04000000 /* Global reset */
+#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
+#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
+#define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */
+#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
+#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
+#define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to manageability engine */
+
+/* Device Status */
+#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
+#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
+#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
+#define E1000_STATUS_FUNC_SHIFT 2
+#define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */
+#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
+#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
+#define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */
+#define E1000_STATUS_SPEED_MASK 0x000000C0
+#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
+#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
+#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
+#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion
+ by EEPROM/Flash */
+#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */
+#define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. Clear on write '0'. */
+#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
+#define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */
+#define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */
+#define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */
+#define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */
+#define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */
+#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */
+#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */
+#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */
+#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */
+#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution disabled */
+#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */
+#define E1000_STATUS_FUSE_8 0x04000000
+#define E1000_STATUS_FUSE_9 0x08000000
+#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */
+#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */
+
+/* Constants used to interpret the masked PCI-X bus speed. */
+#define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */
+#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed 66-100 MHz */
+#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /* PCI-X bus speed 100-133 MHz */
+
+/* EEPROM/Flash Control */
+#define E1000_EECD_SK 0x00000001 /* EEPROM Clock */
+#define E1000_EECD_CS 0x00000002 /* EEPROM Chip Select */
+#define E1000_EECD_DI 0x00000004 /* EEPROM Data In */
+#define E1000_EECD_DO 0x00000008 /* EEPROM Data Out */
+#define E1000_EECD_FWE_MASK 0x00000030
+#define E1000_EECD_FWE_DIS 0x00000010 /* Disable FLASH writes */
+#define E1000_EECD_FWE_EN 0x00000020 /* Enable FLASH writes */
+#define E1000_EECD_FWE_SHIFT 4
+#define E1000_EECD_REQ 0x00000040 /* EEPROM Access Request */
+#define E1000_EECD_GNT 0x00000080 /* EEPROM Access Grant */
+#define E1000_EECD_PRES 0x00000100 /* EEPROM Present */
+#define E1000_EECD_SIZE 0x00000200 /* EEPROM Size (0=64 word 1=256 word) */
+#define E1000_EECD_ADDR_BITS 0x00000400 /* EEPROM Addressing bits based on type
+ * (0-small, 1-large) */
+#define E1000_EECD_TYPE 0x00002000 /* EEPROM Type (1-SPI, 0-Microwire) */
+#ifndef E1000_EEPROM_GRANT_ATTEMPTS
+#define E1000_EEPROM_GRANT_ATTEMPTS 1000 /* EEPROM # attempts to gain grant */
+#endif
+#define E1000_EECD_AUTO_RD 0x00000200 /* EEPROM Auto Read done */
+#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* EEprom Size */
+#define E1000_EECD_SIZE_EX_SHIFT 11
+#define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */
+#define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */
+#define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */
+#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */
+#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */
+#define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */
+#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
+#define E1000_EECD_SECVAL_SHIFT 22
+#define E1000_STM_OPCODE 0xDB00
+#define E1000_HICR_FW_RESET 0xC0
+
+#define E1000_SHADOW_RAM_WORDS 2048
+#define E1000_ICH_NVM_SIG_WORD 0x13
+#define E1000_ICH_NVM_SIG_MASK 0xC0
+
+/* EEPROM Read */
+#define E1000_EERD_START 0x00000001 /* Start Read */
+#define E1000_EERD_DONE 0x00000010 /* Read Done */
+#define E1000_EERD_ADDR_SHIFT 8
+#define E1000_EERD_ADDR_MASK 0x0000FF00 /* Read Address */
+#define E1000_EERD_DATA_SHIFT 16
+#define E1000_EERD_DATA_MASK 0xFFFF0000 /* Read Data */
+
+/* SPI EEPROM Status Register */
+#define EEPROM_STATUS_RDY_SPI 0x01
+#define EEPROM_STATUS_WEN_SPI 0x02
+#define EEPROM_STATUS_BP0_SPI 0x04
+#define EEPROM_STATUS_BP1_SPI 0x08
+#define EEPROM_STATUS_WPEN_SPI 0x80
+
+/* Extended Device Control */
+#define E1000_CTRL_EXT_GPI0_EN 0x00000001 /* Maps SDP4 to GPI0 */
+#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */
+#define E1000_CTRL_EXT_PHYINT_EN E1000_CTRL_EXT_GPI1_EN
+#define E1000_CTRL_EXT_GPI2_EN 0x00000004 /* Maps SDP6 to GPI2 */
+#define E1000_CTRL_EXT_GPI3_EN 0x00000008 /* Maps SDP7 to GPI3 */
+#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable Pin 4 */
+#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable Pin 5 */
+#define E1000_CTRL_EXT_PHY_INT E1000_CTRL_EXT_SDP5_DATA
+#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Defineable Pin 6 */
+#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
+#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */
+#define E1000_CTRL_EXT_SDP5_DIR 0x00000200 /* Direction of SDP5 0=in 1=out */
+#define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */
+#define E1000_CTRL_EXT_SDP7_DIR 0x00000800 /* Direction of SDP7 0=in 1=out */
+#define E1000_CTRL_EXT_ASDCHK 0x00001000 /* Initiate an ASD sequence */
+#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
+#define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */
+#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
+#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
+#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000
+#define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_KMRN 0x00000000
+#define E1000_CTRL_EXT_LINK_MODE_SERDES 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000
+#define E1000_CTRL_EXT_WR_WMARK_MASK 0x03000000
+#define E1000_CTRL_EXT_WR_WMARK_256 0x00000000
+#define E1000_CTRL_EXT_WR_WMARK_320 0x01000000
+#define E1000_CTRL_EXT_WR_WMARK_384 0x02000000
+#define E1000_CTRL_EXT_WR_WMARK_448 0x03000000
+#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
+#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
+#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
+#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error detection enabled */
+#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity error detection enable */
+#define E1000_CTRL_EXT_GHOST_PAREN 0x40000000
+
+/* MDI Control */
+#define E1000_MDIC_DATA_MASK 0x0000FFFF
+#define E1000_MDIC_REG_MASK 0x001F0000
+#define E1000_MDIC_REG_SHIFT 16
+#define E1000_MDIC_PHY_MASK 0x03E00000
+#define E1000_MDIC_PHY_SHIFT 21
+#define E1000_MDIC_OP_WRITE 0x04000000
+#define E1000_MDIC_OP_READ 0x08000000
+#define E1000_MDIC_READY 0x10000000
+#define E1000_MDIC_INT_EN 0x20000000
+#define E1000_MDIC_ERROR 0x40000000
+
+#define E1000_KUMCTRLSTA_MASK 0x0000FFFF
+#define E1000_KUMCTRLSTA_OFFSET 0x001F0000
+#define E1000_KUMCTRLSTA_OFFSET_SHIFT 16
+#define E1000_KUMCTRLSTA_REN 0x00200000
+
+#define E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL 0x00000000
+#define E1000_KUMCTRLSTA_OFFSET_CTRL 0x00000001
+#define E1000_KUMCTRLSTA_OFFSET_INB_CTRL 0x00000002
+#define E1000_KUMCTRLSTA_OFFSET_DIAG 0x00000003
+#define E1000_KUMCTRLSTA_OFFSET_TIMEOUTS 0x00000004
+#define E1000_KUMCTRLSTA_OFFSET_INB_PARAM 0x00000009
+#define E1000_KUMCTRLSTA_OFFSET_HD_CTRL 0x00000010
+#define E1000_KUMCTRLSTA_OFFSET_M2P_SERDES 0x0000001E
+#define E1000_KUMCTRLSTA_OFFSET_M2P_MODES 0x0000001F
+
+/* FIFO Control */
+#define E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS 0x00000008
+#define E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS 0x00000800
+
+/* In-Band Control */
+#define E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT 0x00000500
+#define E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING 0x00000010
+
+/* Half-Duplex Control */
+#define E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT 0x00000004
+#define E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT 0x00000000
+
+#define E1000_KUMCTRLSTA_OFFSET_K0S_CTRL 0x0000001E
+
+#define E1000_KUMCTRLSTA_DIAG_FELPBK 0x2000
+#define E1000_KUMCTRLSTA_DIAG_NELPBK 0x1000
+
+#define E1000_KUMCTRLSTA_K0S_100_EN 0x2000
+#define E1000_KUMCTRLSTA_K0S_GBE_EN 0x1000
+#define E1000_KUMCTRLSTA_K0S_ENTRY_LATENCY_MASK 0x0003
+
+#define E1000_KABGTXD_BGSQLBIAS 0x00050000
+
+#define E1000_PHY_CTRL_SPD_EN 0x00000001
+#define E1000_PHY_CTRL_D0A_LPLU 0x00000002
+#define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004
+#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008
+#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040
+#define E1000_PHY_CTRL_B2B_EN 0x00000080
+
+/* LED Control */
+#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
+#define E1000_LEDCTL_LED0_MODE_SHIFT 0
+#define E1000_LEDCTL_LED0_BLINK_RATE 0x0000020
+#define E1000_LEDCTL_LED0_IVRT 0x00000040
+#define E1000_LEDCTL_LED0_BLINK 0x00000080
+#define E1000_LEDCTL_LED1_MODE_MASK 0x00000F00
+#define E1000_LEDCTL_LED1_MODE_SHIFT 8
+#define E1000_LEDCTL_LED1_BLINK_RATE 0x0002000
+#define E1000_LEDCTL_LED1_IVRT 0x00004000
+#define E1000_LEDCTL_LED1_BLINK 0x00008000
+#define E1000_LEDCTL_LED2_MODE_MASK 0x000F0000
+#define E1000_LEDCTL_LED2_MODE_SHIFT 16
+#define E1000_LEDCTL_LED2_BLINK_RATE 0x00200000
+#define E1000_LEDCTL_LED2_IVRT 0x00400000
+#define E1000_LEDCTL_LED2_BLINK 0x00800000
+#define E1000_LEDCTL_LED3_MODE_MASK 0x0F000000
+#define E1000_LEDCTL_LED3_MODE_SHIFT 24
+#define E1000_LEDCTL_LED3_BLINK_RATE 0x20000000
+#define E1000_LEDCTL_LED3_IVRT 0x40000000
+#define E1000_LEDCTL_LED3_BLINK 0x80000000
+
+#define E1000_LEDCTL_MODE_LINK_10_1000 0x0
+#define E1000_LEDCTL_MODE_LINK_100_1000 0x1
+#define E1000_LEDCTL_MODE_LINK_UP 0x2
+#define E1000_LEDCTL_MODE_ACTIVITY 0x3
+#define E1000_LEDCTL_MODE_LINK_ACTIVITY 0x4
+#define E1000_LEDCTL_MODE_LINK_10 0x5
+#define E1000_LEDCTL_MODE_LINK_100 0x6
+#define E1000_LEDCTL_MODE_LINK_1000 0x7
+#define E1000_LEDCTL_MODE_PCIX_MODE 0x8
+#define E1000_LEDCTL_MODE_FULL_DUPLEX 0x9
+#define E1000_LEDCTL_MODE_COLLISION 0xA
+#define E1000_LEDCTL_MODE_BUS_SPEED 0xB
+#define E1000_LEDCTL_MODE_BUS_SIZE 0xC
+#define E1000_LEDCTL_MODE_PAUSED 0xD
+#define E1000_LEDCTL_MODE_LED_ON 0xE
+#define E1000_LEDCTL_MODE_LED_OFF 0xF
+
+/* Receive Address */
+#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
+
+/* Interrupt Cause Read */
+#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
+#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */
+#define E1000_ICR_LSC 0x00000004 /* Link Status Change */
+#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
+#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
+#define E1000_ICR_RXO 0x00000040 /* rx overrun */
+#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
+#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */
+#define E1000_ICR_RXCFG 0x00000400 /* RX /c/ ordered set */
+#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */
+#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */
+#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */
+#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */
+#define E1000_ICR_TXD_LOW 0x00008000
+#define E1000_ICR_SRPD 0x00010000
+#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */
+#define E1000_ICR_MNG 0x00040000 /* Manageability event */
+#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */
+#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */
+#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity error */
+#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */
+#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */
+#define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW bit in the FWSM */
+#define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates an interrupt */
+#define E1000_ICR_EPRST 0x00100000 /* ME hardware reset occurs */
+
+/* Interrupt Cause Set */
+#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW
+#define E1000_ICS_SRPD E1000_ICR_SRPD
+#define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_ICS_DSW E1000_ICR_DSW
+#define E1000_ICS_PHYINT E1000_ICR_PHYINT
+#define E1000_ICS_EPRST E1000_ICR_EPRST
+
+/* Interrupt Mask Set */
+#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW
+#define E1000_IMS_SRPD E1000_ICR_SRPD
+#define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_IMS_DSW E1000_ICR_DSW
+#define E1000_IMS_PHYINT E1000_ICR_PHYINT
+#define E1000_IMS_EPRST E1000_ICR_EPRST
+
+/* Interrupt Mask Clear */
+#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_IMC_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_IMC_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_IMC_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_IMC_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_IMC_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_IMC_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_IMC_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_IMC_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_IMC_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_IMC_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_IMC_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_IMC_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_IMC_TXD_LOW E1000_ICR_TXD_LOW
+#define E1000_IMC_SRPD E1000_ICR_SRPD
+#define E1000_IMC_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_IMC_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_IMC_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_IMC_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_IMC_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_IMC_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_IMC_DSW E1000_ICR_DSW
+#define E1000_IMC_PHYINT E1000_ICR_PHYINT
+#define E1000_IMC_EPRST E1000_ICR_EPRST
+
+/* Receive Control */
+#define E1000_RCTL_RST 0x00000001 /* Software reset */
+#define E1000_RCTL_EN 0x00000002 /* enable */
+#define E1000_RCTL_SBP 0x00000004 /* store bad packet */
+#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
+#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
+#define E1000_RCTL_LPE 0x00000020 /* long packet enable */
+#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
+#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
+#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */
+#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
+#define E1000_RCTL_DTYP_MASK 0x00000C00 /* Descriptor type mask */
+#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
+#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
+#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */
+#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */
+#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
+#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */
+#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */
+#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */
+#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
+#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */
+#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
+/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
+#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */
+#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */
+#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
+#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
+/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
+#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */
+#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */
+#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */
+#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
+#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
+#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
+#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */
+#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
+#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
+#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
+#define E1000_RCTL_FLXBUF_MASK 0x78000000 /* Flexible buffer size */
+#define E1000_RCTL_FLXBUF_SHIFT 27 /* Flexible buffer shift */
+
+/* Use byte values for the following shift parameters
+ * Usage:
+ * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
+ * E1000_PSRCTL_BSIZE0_MASK) |
+ * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
+ * E1000_PSRCTL_BSIZE1_MASK) |
+ * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
+ * E1000_PSRCTL_BSIZE2_MASK) |
+ * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
+ * E1000_PSRCTL_BSIZE3_MASK))
+ * where value0 = [128..16256], default=256
+ * value1 = [1024..64512], default=4096
+ * value2 = [0..64512], default=4096
+ * value3 = [0..64512], default=0
+ */
+
+#define E1000_PSRCTL_BSIZE0_MASK 0x0000007F
+#define E1000_PSRCTL_BSIZE1_MASK 0x00003F00
+#define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
+#define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
+
+#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
+#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
+#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
+#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
+
+/* SW_W_SYNC definitions */
+#define E1000_SWFW_EEP_SM 0x0001
+#define E1000_SWFW_PHY0_SM 0x0002
+#define E1000_SWFW_PHY1_SM 0x0004
+#define E1000_SWFW_MAC_CSR_SM 0x0008
+
+/* Receive Descriptor */
+#define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */
+#define E1000_RDT_FPDB 0x80000000 /* Flush descriptor block */
+#define E1000_RDLEN_LEN 0x0007ff80 /* descriptor length */
+#define E1000_RDH_RDH 0x0000ffff /* receive descriptor head */
+#define E1000_RDT_RDT 0x0000ffff /* receive descriptor tail */
+
+/* Flow Control */
+#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */
+#define E1000_FCRTH_XFCE 0x80000000 /* External Flow Control Enable */
+#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */
+#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
+
+/* Header split receive */
+#define E1000_RFCTL_ISCSI_DIS 0x00000001
+#define E1000_RFCTL_ISCSI_DWC_MASK 0x0000003E
+#define E1000_RFCTL_ISCSI_DWC_SHIFT 1
+#define E1000_RFCTL_NFSW_DIS 0x00000040
+#define E1000_RFCTL_NFSR_DIS 0x00000080
+#define E1000_RFCTL_NFS_VER_MASK 0x00000300
+#define E1000_RFCTL_NFS_VER_SHIFT 8
+#define E1000_RFCTL_IPV6_DIS 0x00000400
+#define E1000_RFCTL_IPV6_XSUM_DIS 0x00000800
+#define E1000_RFCTL_ACK_DIS 0x00001000
+#define E1000_RFCTL_ACKD_DIS 0x00002000
+#define E1000_RFCTL_IPFRSP_DIS 0x00004000
+#define E1000_RFCTL_EXTEN 0x00008000
+#define E1000_RFCTL_IPV6_EX_DIS 0x00010000
+#define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000
+
+/* Receive Descriptor Control */
+#define E1000_RXDCTL_PTHRESH 0x0000003F /* RXDCTL Prefetch Threshold */
+#define E1000_RXDCTL_HTHRESH 0x00003F00 /* RXDCTL Host Threshold */
+#define E1000_RXDCTL_WTHRESH 0x003F0000 /* RXDCTL Writeback Threshold */
+#define E1000_RXDCTL_GRAN 0x01000000 /* RXDCTL Granularity */
+
+/* Transmit Descriptor Control */
+#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */
+#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */
+#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */
+#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */
+#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */
+#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
+#define E1000_TXDCTL_COUNT_DESC 0x00400000 /* Enable the counting of desc.
+ still to be processed. */
+/* Transmit Configuration Word */
+#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */
+#define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */
+#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
+#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
+#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */
+#define E1000_TXCW_RF 0x00003000 /* TXCW remote fault */
+#define E1000_TXCW_NP 0x00008000 /* TXCW next page */
+#define E1000_TXCW_CW 0x0000ffff /* TxConfigWord mask */
+#define E1000_TXCW_TXC 0x40000000 /* Transmit Config control */
+#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
+
+/* Receive Configuration Word */
+#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */
+#define E1000_RXCW_NC 0x04000000 /* Receive config no carrier */
+#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */
+#define E1000_RXCW_CC 0x10000000 /* Receive config change */
+#define E1000_RXCW_C 0x20000000 /* Receive config */
+#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */
+#define E1000_RXCW_ANC 0x80000000 /* Auto-neg complete */
+
+/* Transmit Control */
+#define E1000_TCTL_RST 0x00000001 /* software reset */
+#define E1000_TCTL_EN 0x00000002 /* enable tx */
+#define E1000_TCTL_BCE 0x00000004 /* busy check enable */
+#define E1000_TCTL_PSP 0x00000008 /* pad short packets */
+#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
+#define E1000_TCTL_COLD 0x003ff000 /* collision distance */
+#define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */
+#define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */
+#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
+#define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */
+#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
+/* Extended Transmit Control */
+#define E1000_TCTL_EXT_BST_MASK 0x000003FF /* Backoff Slot Time */
+#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
+
+/* Receive Checksum Control */
+#define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */
+#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */
+#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
+#define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */
+#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
+#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
+
+/* Multiple Receive Queue Control */
+#define E1000_MRQC_ENABLE_MASK 0x00000003
+#define E1000_MRQC_ENABLE_RSS_2Q 0x00000001
+#define E1000_MRQC_ENABLE_RSS_INT 0x00000004
+#define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000
+#define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
+#define E1000_MRQC_RSS_FIELD_IPV4 0x00020000
+#define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000
+#define E1000_MRQC_RSS_FIELD_IPV6_EX 0x00080000
+#define E1000_MRQC_RSS_FIELD_IPV6 0x00100000
+#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000
+
+/* Definitions for power management and wakeup registers */
+/* Wake Up Control */
+#define E1000_WUC_APME 0x00000001 /* APM Enable */
+#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
+#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */
+#define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */
+#define E1000_WUC_SPM 0x80000000 /* Enable SPM */
+
+/* Wake Up Filter Control */
+#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
+#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
+#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
+#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
+#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
+#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
+#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */
+#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */
+#define E1000_WUFC_IGNORE_TCO 0x00008000 /* Ignore WakeOn TCO packets */
+#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */
+#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */
+#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */
+#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */
+#define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */
+#define E1000_WUFC_FLX_OFFSET 16 /* Offset to the Flexible Filters bits */
+#define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
+
+/* Wake Up Status */
+#define E1000_WUS_LNKC 0x00000001 /* Link Status Changed */
+#define E1000_WUS_MAG 0x00000002 /* Magic Packet Received */
+#define E1000_WUS_EX 0x00000004 /* Directed Exact Received */
+#define E1000_WUS_MC 0x00000008 /* Directed Multicast Received */
+#define E1000_WUS_BC 0x00000010 /* Broadcast Received */
+#define E1000_WUS_ARP 0x00000020 /* ARP Request Packet Received */
+#define E1000_WUS_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Received */
+#define E1000_WUS_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Received */
+#define E1000_WUS_FLX0 0x00010000 /* Flexible Filter 0 Match */
+#define E1000_WUS_FLX1 0x00020000 /* Flexible Filter 1 Match */
+#define E1000_WUS_FLX2 0x00040000 /* Flexible Filter 2 Match */
+#define E1000_WUS_FLX3 0x00080000 /* Flexible Filter 3 Match */
+#define E1000_WUS_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
+
+/* Management Control */
+#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
+#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
+#define E1000_MANC_R_ON_FORCE 0x00000004 /* Reset on Force TCO - RO */
+#define E1000_MANC_RMCP_EN 0x00000100 /* Enable RCMP 026Fh Filtering */
+#define E1000_MANC_0298_EN 0x00000200 /* Enable RCMP 0298h Filtering */
+#define E1000_MANC_IPV4_EN 0x00000400 /* Enable IPv4 */
+#define E1000_MANC_IPV6_EN 0x00000800 /* Enable IPv6 */
+#define E1000_MANC_SNAP_EN 0x00001000 /* Accept LLC/SNAP */
+#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
+#define E1000_MANC_NEIGHBOR_EN 0x00004000 /* Enable Neighbor Discovery
+ * Filtering */
+#define E1000_MANC_ARP_RES_EN 0x00008000 /* Enable ARP response Filtering */
+#define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */
+#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
+#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */
+#define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */
+#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
+#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 /* Enable MAC address
+ * filtering */
+#define E1000_MANC_EN_MNG2HOST 0x00200000 /* Enable MNG packets to host
+ * memory */
+#define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000 /* Enable IP address
+ * filtering */
+#define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */
+#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */
+#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */
+#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */
+#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */
+#define E1000_MANC_SMB_DATA_IN 0x08000000 /* SMBus Data In */
+#define E1000_MANC_SMB_DATA_OUT 0x10000000 /* SMBus Data Out */
+#define E1000_MANC_SMB_CLK_OUT 0x20000000 /* SMBus Clock Out */
+
+#define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */
+#define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */
+
+/* SW Semaphore Register */
+#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
+#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
+#define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */
+#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */
+
+/* FW Semaphore Register */
+#define E1000_FWSM_MODE_MASK 0x0000000E /* FW mode */
+#define E1000_FWSM_MODE_SHIFT 1
+#define E1000_FWSM_FW_VALID 0x00008000 /* FW established a valid mode */
+
+#define E1000_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI reset */
+#define E1000_FWSM_DISSW 0x10000000 /* FW disable SW Write Access */
+#define E1000_FWSM_SKUSEL_MASK 0x60000000 /* LAN SKU select */
+#define E1000_FWSM_SKUEL_SHIFT 29
+#define E1000_FWSM_SKUSEL_EMB 0x0 /* Embedded SKU */
+#define E1000_FWSM_SKUSEL_CONS 0x1 /* Consumer SKU */
+#define E1000_FWSM_SKUSEL_PERF_100 0x2 /* Perf & Corp 10/100 SKU */
+#define E1000_FWSM_SKUSEL_PERF_GBE 0x3 /* Perf & Copr GbE SKU */
+
+/* FFLT Debug Register */
+#define E1000_FFLT_DBG_INVC 0x00100000 /* Invalid /C/ code handling */
+
+typedef enum {
+ e1000_mng_mode_none = 0,
+ e1000_mng_mode_asf,
+ e1000_mng_mode_pt,
+ e1000_mng_mode_ipmi,
+ e1000_mng_mode_host_interface_only
+} e1000_mng_mode;
+
+/* Host Interface Control Register */
+#define E1000_HICR_EN 0x00000001 /* Enable Bit - RO */
+#define E1000_HICR_C 0x00000002 /* Driver sets this bit when done
+ * to put command in RAM */
+#define E1000_HICR_SV 0x00000004 /* Status Validity */
+#define E1000_HICR_FWR 0x00000080 /* FW reset. Set by the Host */
+
+/* Host Interface Command Interface - Address range 0x8800-0x8EFF */
+#define E1000_HI_MAX_DATA_LENGTH 252 /* Host Interface data length */
+#define E1000_HI_MAX_BLOCK_BYTE_LENGTH 1792 /* Number of bytes in range */
+#define E1000_HI_MAX_BLOCK_DWORD_LENGTH 448 /* Number of dwords in range */
+#define E1000_HI_COMMAND_TIMEOUT 500 /* Time in ms to process HI command */
+
+struct e1000_host_command_header {
+ u8 command_id;
+ u8 command_length;
+ u8 command_options; /* I/F bits for command, status for return */
+ u8 checksum;
+};
+struct e1000_host_command_info {
+ struct e1000_host_command_header command_header; /* Command Head/Command Result Head has 4 bytes */
+ u8 command_data[E1000_HI_MAX_DATA_LENGTH]; /* Command data can length 0..252 */
+};
+
+/* Host SMB register #0 */
+#define E1000_HSMC0R_CLKIN 0x00000001 /* SMB Clock in */
+#define E1000_HSMC0R_DATAIN 0x00000002 /* SMB Data in */
+#define E1000_HSMC0R_DATAOUT 0x00000004 /* SMB Data out */
+#define E1000_HSMC0R_CLKOUT 0x00000008 /* SMB Clock out */
+
+/* Host SMB register #1 */
+#define E1000_HSMC1R_CLKIN E1000_HSMC0R_CLKIN
+#define E1000_HSMC1R_DATAIN E1000_HSMC0R_DATAIN
+#define E1000_HSMC1R_DATAOUT E1000_HSMC0R_DATAOUT
+#define E1000_HSMC1R_CLKOUT E1000_HSMC0R_CLKOUT
+
+/* FW Status Register */
+#define E1000_FWSTS_FWS_MASK 0x000000FF /* FW Status */
+
+/* Wake Up Packet Length */
+#define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */
+
+#define E1000_MDALIGN 4096
+
+/* PCI-Ex registers*/
+
+/* PCI-Ex Control Register */
+#define E1000_GCR_RXD_NO_SNOOP 0x00000001
+#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002
+#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004
+#define E1000_GCR_TXD_NO_SNOOP 0x00000008
+#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010
+#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020
+
+#define PCI_EX_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \
+ E1000_GCR_RXDSCW_NO_SNOOP | \
+ E1000_GCR_RXDSCR_NO_SNOOP | \
+ E1000_GCR_TXD_NO_SNOOP | \
+ E1000_GCR_TXDSCW_NO_SNOOP | \
+ E1000_GCR_TXDSCR_NO_SNOOP)
+
+#define PCI_EX_82566_SNOOP_ALL PCI_EX_NO_SNOOP_ALL
+
+#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
+/* Function Active and Power State to MNG */
+#define E1000_FACTPS_FUNC0_POWER_STATE_MASK 0x00000003
+#define E1000_FACTPS_LAN0_VALID 0x00000004
+#define E1000_FACTPS_FUNC0_AUX_EN 0x00000008
+#define E1000_FACTPS_FUNC1_POWER_STATE_MASK 0x000000C0
+#define E1000_FACTPS_FUNC1_POWER_STATE_SHIFT 6
+#define E1000_FACTPS_LAN1_VALID 0x00000100
+#define E1000_FACTPS_FUNC1_AUX_EN 0x00000200
+#define E1000_FACTPS_FUNC2_POWER_STATE_MASK 0x00003000
+#define E1000_FACTPS_FUNC2_POWER_STATE_SHIFT 12
+#define E1000_FACTPS_IDE_ENABLE 0x00004000
+#define E1000_FACTPS_FUNC2_AUX_EN 0x00008000
+#define E1000_FACTPS_FUNC3_POWER_STATE_MASK 0x000C0000
+#define E1000_FACTPS_FUNC3_POWER_STATE_SHIFT 18
+#define E1000_FACTPS_SP_ENABLE 0x00100000
+#define E1000_FACTPS_FUNC3_AUX_EN 0x00200000
+#define E1000_FACTPS_FUNC4_POWER_STATE_MASK 0x03000000
+#define E1000_FACTPS_FUNC4_POWER_STATE_SHIFT 24
+#define E1000_FACTPS_IPMI_ENABLE 0x04000000
+#define E1000_FACTPS_FUNC4_AUX_EN 0x08000000
+#define E1000_FACTPS_MNGCG 0x20000000
+#define E1000_FACTPS_LAN_FUNC_SEL 0x40000000
+#define E1000_FACTPS_PM_STATE_CHANGED 0x80000000
+
+/* PCI-Ex Config Space */
+#define PCI_EX_LINK_STATUS 0x12
+#define PCI_EX_LINK_WIDTH_MASK 0x3F0
+#define PCI_EX_LINK_WIDTH_SHIFT 4
+
+/* EEPROM Commands - Microwire */
+#define EEPROM_READ_OPCODE_MICROWIRE 0x6 /* EEPROM read opcode */
+#define EEPROM_WRITE_OPCODE_MICROWIRE 0x5 /* EEPROM write opcode */
+#define EEPROM_ERASE_OPCODE_MICROWIRE 0x7 /* EEPROM erase opcode */
+#define EEPROM_EWEN_OPCODE_MICROWIRE 0x13 /* EEPROM erase/write enable */
+#define EEPROM_EWDS_OPCODE_MICROWIRE 0x10 /* EEPROM erase/write disable */
+
+/* EEPROM Commands - SPI */
+#define EEPROM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
+#define EEPROM_READ_OPCODE_SPI 0x03 /* EEPROM read opcode */
+#define EEPROM_WRITE_OPCODE_SPI 0x02 /* EEPROM write opcode */
+#define EEPROM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
+#define EEPROM_WREN_OPCODE_SPI 0x06 /* EEPROM set Write Enable latch */
+#define EEPROM_WRDI_OPCODE_SPI 0x04 /* EEPROM reset Write Enable latch */
+#define EEPROM_RDSR_OPCODE_SPI 0x05 /* EEPROM read Status register */
+#define EEPROM_WRSR_OPCODE_SPI 0x01 /* EEPROM write Status register */
+#define EEPROM_ERASE4K_OPCODE_SPI 0x20 /* EEPROM ERASE 4KB */
+#define EEPROM_ERASE64K_OPCODE_SPI 0xD8 /* EEPROM ERASE 64KB */
+#define EEPROM_ERASE256_OPCODE_SPI 0xDB /* EEPROM ERASE 256B */
+
+/* EEPROM Size definitions */
+#define EEPROM_WORD_SIZE_SHIFT 6
+#define EEPROM_SIZE_SHIFT 10
+#define EEPROM_SIZE_MASK 0x1C00
+
+/* EEPROM Word Offsets */
+#define EEPROM_COMPAT 0x0003
+#define EEPROM_ID_LED_SETTINGS 0x0004
+#define EEPROM_VERSION 0x0005
+#define EEPROM_SERDES_AMPLITUDE 0x0006 /* For SERDES output amplitude adjustment. */
+#define EEPROM_PHY_CLASS_WORD 0x0007
+#define EEPROM_INIT_CONTROL1_REG 0x000A
+#define EEPROM_INIT_CONTROL2_REG 0x000F
+#define EEPROM_SWDEF_PINS_CTRL_PORT_1 0x0010
+#define EEPROM_INIT_CONTROL3_PORT_B 0x0014
+#define EEPROM_INIT_3GIO_3 0x001A
+#define EEPROM_SWDEF_PINS_CTRL_PORT_0 0x0020
+#define EEPROM_INIT_CONTROL3_PORT_A 0x0024
+#define EEPROM_CFG 0x0012
+#define EEPROM_FLASH_VERSION 0x0032
+#define EEPROM_CHECKSUM_REG 0x003F
+
+#define E1000_EEPROM_CFG_DONE 0x00040000 /* MNG config cycle done */
+#define E1000_EEPROM_CFG_DONE_PORT_1 0x00080000 /* ...for second port */
+
+/* Word definitions for ID LED Settings */
+#define ID_LED_RESERVED_0000 0x0000
+#define ID_LED_RESERVED_FFFF 0xFFFF
+#define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
+ (ID_LED_OFF1_OFF2 << 8) | \
+ (ID_LED_DEF1_DEF2 << 4) | \
+ (ID_LED_DEF1_DEF2))
+#define ID_LED_DEF1_DEF2 0x1
+#define ID_LED_DEF1_ON2 0x2
+#define ID_LED_DEF1_OFF2 0x3
+#define ID_LED_ON1_DEF2 0x4
+#define ID_LED_ON1_ON2 0x5
+#define ID_LED_ON1_OFF2 0x6
+#define ID_LED_OFF1_DEF2 0x7
+#define ID_LED_OFF1_ON2 0x8
+#define ID_LED_OFF1_OFF2 0x9
+
+#define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF
+#define IGP_ACTIVITY_LED_ENABLE 0x0300
+#define IGP_LED3_MODE 0x07000000
+
+/* Mask bits for SERDES amplitude adjustment in Word 6 of the EEPROM */
+#define EEPROM_SERDES_AMPLITUDE_MASK 0x000F
+
+/* Mask bit for PHY class in Word 7 of the EEPROM */
+#define EEPROM_PHY_CLASS_A 0x8000
+
+/* Mask bits for fields in Word 0x0a of the EEPROM */
+#define EEPROM_WORD0A_ILOS 0x0010
+#define EEPROM_WORD0A_SWDPIO 0x01E0
+#define EEPROM_WORD0A_LRST 0x0200
+#define EEPROM_WORD0A_FD 0x0400
+#define EEPROM_WORD0A_66MHZ 0x0800
+
+/* Mask bits for fields in Word 0x0f of the EEPROM */
+#define EEPROM_WORD0F_PAUSE_MASK 0x3000
+#define EEPROM_WORD0F_PAUSE 0x1000
+#define EEPROM_WORD0F_ASM_DIR 0x2000
+#define EEPROM_WORD0F_ANE 0x0800
+#define EEPROM_WORD0F_SWPDIO_EXT 0x00F0
+#define EEPROM_WORD0F_LPLU 0x0001
+
+/* Mask bits for fields in Word 0x10/0x20 of the EEPROM */
+#define EEPROM_WORD1020_GIGA_DISABLE 0x0010
+#define EEPROM_WORD1020_GIGA_DISABLE_NON_D0A 0x0008
+
+/* Mask bits for fields in Word 0x1a of the EEPROM */
+#define EEPROM_WORD1A_ASPM_MASK 0x000C
+
+/* For checksumming, the sum of all words in the EEPROM should equal 0xBABA. */
+#define EEPROM_SUM 0xBABA
+
+/* EEPROM Map defines (WORD OFFSETS)*/
+#define EEPROM_NODE_ADDRESS_BYTE_0 0
+#define EEPROM_PBA_BYTE_1 8
+
+#define EEPROM_RESERVED_WORD 0xFFFF
+
+/* EEPROM Map Sizes (Byte Counts) */
+#define PBA_SIZE 4
+
+/* Collision related configuration parameters */
+#define E1000_COLLISION_THRESHOLD 15
+#define E1000_CT_SHIFT 4
+/* Collision distance is a 0-based value that applies to
+ * half-duplex-capable hardware only. */
+#define E1000_COLLISION_DISTANCE 63
+#define E1000_COLLISION_DISTANCE_82542 64
+#define E1000_FDX_COLLISION_DISTANCE E1000_COLLISION_DISTANCE
+#define E1000_HDX_COLLISION_DISTANCE E1000_COLLISION_DISTANCE
+#define E1000_COLD_SHIFT 12
+
+/* Number of Transmit and Receive Descriptors must be a multiple of 8 */
+#define REQ_TX_DESCRIPTOR_MULTIPLE 8
+#define REQ_RX_DESCRIPTOR_MULTIPLE 8
+
+/* Default values for the transmit IPG register */
+#define DEFAULT_82542_TIPG_IPGT 10
+#define DEFAULT_82543_TIPG_IPGT_FIBER 9
+#define DEFAULT_82543_TIPG_IPGT_COPPER 8
+
+#define E1000_TIPG_IPGT_MASK 0x000003FF
+#define E1000_TIPG_IPGR1_MASK 0x000FFC00
+#define E1000_TIPG_IPGR2_MASK 0x3FF00000
+
+#define DEFAULT_82542_TIPG_IPGR1 2
+#define DEFAULT_82543_TIPG_IPGR1 8
+#define E1000_TIPG_IPGR1_SHIFT 10
+
+#define DEFAULT_82542_TIPG_IPGR2 10
+#define DEFAULT_82543_TIPG_IPGR2 6
+#define E1000_TIPG_IPGR2_SHIFT 20
+
+#define E1000_TXDMAC_DPP 0x00000001
+
+/* Adaptive IFS defines */
+#define TX_THRESHOLD_START 8
+#define TX_THRESHOLD_INCREMENT 10
+#define TX_THRESHOLD_DECREMENT 1
+#define TX_THRESHOLD_STOP 190
+#define TX_THRESHOLD_DISABLE 0
+#define TX_THRESHOLD_TIMER_MS 10000
+#define MIN_NUM_XMITS 1000
+#define IFS_MAX 80
+#define IFS_STEP 10
+#define IFS_MIN 40
+#define IFS_RATIO 4
+
+/* Extended Configuration Control and Size */
+#define E1000_EXTCNF_CTRL_PCIE_WRITE_ENABLE 0x00000001
+#define E1000_EXTCNF_CTRL_PHY_WRITE_ENABLE 0x00000002
+#define E1000_EXTCNF_CTRL_D_UD_ENABLE 0x00000004
+#define E1000_EXTCNF_CTRL_D_UD_LATENCY 0x00000008
+#define E1000_EXTCNF_CTRL_D_UD_OWNER 0x00000010
+#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
+#define E1000_EXTCNF_CTRL_MDIO_HW_OWNERSHIP 0x00000040
+#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER 0x0FFF0000
+
+#define E1000_EXTCNF_SIZE_EXT_PHY_LENGTH 0x000000FF
+#define E1000_EXTCNF_SIZE_EXT_DOCK_LENGTH 0x0000FF00
+#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH 0x00FF0000
+#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001
+#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
+
+/* PBA constants */
+#define E1000_PBA_8K 0x0008 /* 8KB, default Rx allocation */
+#define E1000_PBA_12K 0x000C /* 12KB, default Rx allocation */
+#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */
+#define E1000_PBA_20K 0x0014
+#define E1000_PBA_22K 0x0016
+#define E1000_PBA_24K 0x0018
+#define E1000_PBA_30K 0x001E
+#define E1000_PBA_32K 0x0020
+#define E1000_PBA_34K 0x0022
+#define E1000_PBA_38K 0x0026
+#define E1000_PBA_40K 0x0028
+#define E1000_PBA_48K 0x0030 /* 48KB, default RX allocation */
+
+#define E1000_PBS_16K E1000_PBA_16K
+
+/* Flow Control Constants */
+#define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
+#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
+#define FLOW_CONTROL_TYPE 0x8808
+
+/* The historical defaults for the flow control values are given below. */
+#define FC_DEFAULT_HI_THRESH (0x8000) /* 32KB */
+#define FC_DEFAULT_LO_THRESH (0x4000) /* 16KB */
+#define FC_DEFAULT_TX_TIMER (0x100) /* ~130 us */
+
+/* PCIX Config space */
+#define PCIX_COMMAND_REGISTER 0xE6
+#define PCIX_STATUS_REGISTER_LO 0xE8
+#define PCIX_STATUS_REGISTER_HI 0xEA
+
+#define PCIX_COMMAND_MMRBC_MASK 0x000C
+#define PCIX_COMMAND_MMRBC_SHIFT 0x2
+#define PCIX_STATUS_HI_MMRBC_MASK 0x0060
+#define PCIX_STATUS_HI_MMRBC_SHIFT 0x5
+#define PCIX_STATUS_HI_MMRBC_4K 0x3
+#define PCIX_STATUS_HI_MMRBC_2K 0x2
+
+/* Number of bits required to shift right the "pause" bits from the
+ * EEPROM (bits 13:12) to the "pause" (bits 8:7) field in the TXCW register.
+ */
+#define PAUSE_SHIFT 5
+
+/* Number of bits required to shift left the "SWDPIO" bits from the
+ * EEPROM (bits 8:5) to the "SWDPIO" (bits 25:22) field in the CTRL register.
+ */
+#define SWDPIO_SHIFT 17
+
+/* Number of bits required to shift left the "SWDPIO_EXT" bits from the
+ * EEPROM word F (bits 7:4) to the bits 11:8 of The Extended CTRL register.
+ */
+#define SWDPIO__EXT_SHIFT 4
+
+/* Number of bits required to shift left the "ILOS" bit from the EEPROM
+ * (bit 4) to the "ILOS" (bit 7) field in the CTRL register.
+ */
+#define ILOS_SHIFT 3
+
+#define RECEIVE_BUFFER_ALIGN_SIZE (256)
+
+/* Number of milliseconds we wait for auto-negotiation to complete */
+#define LINK_UP_TIMEOUT 500
+
+/* Number of milliseconds we wait for Eeprom auto read bit done after MAC reset */
+#define AUTO_READ_DONE_TIMEOUT 10
+/* Number of milliseconds we wait for PHY configuration done after MAC reset */
+#define PHY_CFG_TIMEOUT 100
+
+#define E1000_TX_BUFFER_SIZE ((u32)1514)
+
+/* The carrier extension symbol, as received by the NIC. */
+#define CARRIER_EXTENSION 0x0F
+
+/* TBI_ACCEPT macro definition:
+ *
+ * This macro requires:
+ * adapter = a pointer to struct e1000_hw
+ * status = the 8 bit status field of the RX descriptor with EOP set
+ * error = the 8 bit error field of the RX descriptor with EOP set
+ * length = the sum of all the length fields of the RX descriptors that
+ * make up the current frame
+ * last_byte = the last byte of the frame DMAed by the hardware
+ * max_frame_length = the maximum frame length we want to accept.
+ * min_frame_length = the minimum frame length we want to accept.
+ *
+ * This macro is a conditional that should be used in the interrupt
+ * handler's Rx processing routine when RxErrors have been detected.
+ *
+ * Typical use:
+ * ...
+ * if (TBI_ACCEPT) {
+ * accept_frame = true;
+ * e1000_tbi_adjust_stats(adapter, MacAddress);
+ * frame_length--;
+ * } else {
+ * accept_frame = false;
+ * }
+ * ...
+ */
+
+#define TBI_ACCEPT(adapter, status, errors, length, last_byte) \
+ ((adapter)->tbi_compatibility_on && \
+ (((errors) & E1000_RXD_ERR_FRAME_ERR_MASK) == E1000_RXD_ERR_CE) && \
+ ((last_byte) == CARRIER_EXTENSION) && \
+ (((status) & E1000_RXD_STAT_VP) ? \
+ (((length) > ((adapter)->min_frame_size - VLAN_TAG_SIZE)) && \
+ ((length) <= ((adapter)->max_frame_size + 1))) : \
+ (((length) > (adapter)->min_frame_size) && \
+ ((length) <= ((adapter)->max_frame_size + VLAN_TAG_SIZE + 1)))))
+
+/* Structures, enums, and macros for the PHY */
+
+/* Bit definitions for the Management Data IO (MDIO) and Management Data
+ * Clock (MDC) pins in the Device Control Register.
+ */
+#define E1000_CTRL_PHY_RESET_DIR E1000_CTRL_SWDPIO0
+#define E1000_CTRL_PHY_RESET E1000_CTRL_SWDPIN0
+#define E1000_CTRL_MDIO_DIR E1000_CTRL_SWDPIO2
+#define E1000_CTRL_MDIO E1000_CTRL_SWDPIN2
+#define E1000_CTRL_MDC_DIR E1000_CTRL_SWDPIO3
+#define E1000_CTRL_MDC E1000_CTRL_SWDPIN3
+#define E1000_CTRL_PHY_RESET_DIR4 E1000_CTRL_EXT_SDP4_DIR
+#define E1000_CTRL_PHY_RESET4 E1000_CTRL_EXT_SDP4_DATA
+
+/* PHY 1000 MII Register/Bit Definitions */
+/* PHY Registers defined by IEEE */
+#define PHY_CTRL 0x00 /* Control Register */
+#define PHY_STATUS 0x01 /* Status Register */
+#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
+#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
+#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
+#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
+#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */
+#define PHY_NEXT_PAGE_TX 0x07 /* Next Page TX */
+#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */
+#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
+#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
+#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */
+
+#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
+#define MAX_PHY_MULTI_PAGE_REG 0xF /* Registers equal on all pages */
+
+/* M88E1000 Specific Registers */
+#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
+#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
+#define M88E1000_INT_ENABLE 0x12 /* Interrupt Enable Register */
+#define M88E1000_INT_STATUS 0x13 /* Interrupt Status Register */
+#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
+#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */
+
+#define M88E1000_PHY_EXT_CTRL 0x1A /* PHY extend control register */
+#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
+#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
+#define M88E1000_PHY_VCO_REG_BIT8 0x100 /* Bits 8 & 11 are adjusted for */
+#define M88E1000_PHY_VCO_REG_BIT11 0x800 /* improved BER performance */
+
+#define IGP01E1000_IEEE_REGS_PAGE 0x0000
+#define IGP01E1000_IEEE_RESTART_AUTONEG 0x3300
+#define IGP01E1000_IEEE_FORCE_GIGA 0x0140
+
+/* IGP01E1000 Specific Registers */
+#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* PHY Specific Port Config Register */
+#define IGP01E1000_PHY_PORT_STATUS 0x11 /* PHY Specific Status Register */
+#define IGP01E1000_PHY_PORT_CTRL 0x12 /* PHY Specific Control Register */
+#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health Register */
+#define IGP01E1000_GMII_FIFO 0x14 /* GMII FIFO Register */
+#define IGP01E1000_PHY_CHANNEL_QUALITY 0x15 /* PHY Channel Quality Register */
+#define IGP02E1000_PHY_POWER_MGMT 0x19
+#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* PHY Page Select Core Register */
+
+/* IGP01E1000 AGC Registers - stores the cable length values*/
+#define IGP01E1000_PHY_AGC_A 0x1172
+#define IGP01E1000_PHY_AGC_B 0x1272
+#define IGP01E1000_PHY_AGC_C 0x1472
+#define IGP01E1000_PHY_AGC_D 0x1872
+
+/* IGP02E1000 AGC Registers for cable length values */
+#define IGP02E1000_PHY_AGC_A 0x11B1
+#define IGP02E1000_PHY_AGC_B 0x12B1
+#define IGP02E1000_PHY_AGC_C 0x14B1
+#define IGP02E1000_PHY_AGC_D 0x18B1
+
+/* IGP01E1000 DSP Reset Register */
+#define IGP01E1000_PHY_DSP_RESET 0x1F33
+#define IGP01E1000_PHY_DSP_SET 0x1F71
+#define IGP01E1000_PHY_DSP_FFE 0x1F35
+
+#define IGP01E1000_PHY_CHANNEL_NUM 4
+#define IGP02E1000_PHY_CHANNEL_NUM 4
+
+#define IGP01E1000_PHY_AGC_PARAM_A 0x1171
+#define IGP01E1000_PHY_AGC_PARAM_B 0x1271
+#define IGP01E1000_PHY_AGC_PARAM_C 0x1471
+#define IGP01E1000_PHY_AGC_PARAM_D 0x1871
+
+#define IGP01E1000_PHY_EDAC_MU_INDEX 0xC000
+#define IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS 0x8000
+
+#define IGP01E1000_PHY_ANALOG_TX_STATE 0x2890
+#define IGP01E1000_PHY_ANALOG_CLASS_A 0x2000
+#define IGP01E1000_PHY_FORCE_ANALOG_ENABLE 0x0004
+#define IGP01E1000_PHY_DSP_FFE_CM_CP 0x0069
+
+#define IGP01E1000_PHY_DSP_FFE_DEFAULT 0x002A
+/* IGP01E1000 PCS Initialization register - stores the polarity status when
+ * speed = 1000 Mbps. */
+#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4
+#define IGP01E1000_PHY_PCS_CTRL_REG 0x00B5
+
+#define IGP01E1000_ANALOG_REGS_PAGE 0x20C0
+
+/* PHY Control Register */
+#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */
+#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
+#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
+#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */
+#define MII_CR_POWER_DOWN 0x0800 /* Power down */
+#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
+#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
+#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
+
+/* PHY Status Register */
+#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */
+#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */
+#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
+#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */
+#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */
+#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
+#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */
+#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */
+#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */
+#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */
+#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */
+#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */
+#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */
+#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */
+#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */
+
+/* Autoneg Advertisement Register */
+#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */
+#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
+#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
+#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
+#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
+#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */
+#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
+#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
+#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */
+#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */
+
+/* Link Partner Ability Register (Base Page) */
+#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */
+#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */
+#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */
+#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */
+#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */
+#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */
+#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
+#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
+#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */
+#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */
+#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */
+
+/* Autoneg Expansion Register */
+#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */
+#define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */
+#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */
+#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */
+#define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP is 100TX Full Duplex Capable */
+
+/* Next Page TX Register */
+#define NPTX_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
+#define NPTX_TOGGLE 0x0800 /* Toggles between exchanges
+ * of different NP
+ */
+#define NPTX_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg
+ * 0 = cannot comply with msg
+ */
+#define NPTX_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */
+#define NPTX_NEXT_PAGE 0x8000 /* 1 = addition NP will follow
+ * 0 = sending last NP
+ */
+
+/* Link Partner Next Page Register */
+#define LP_RNPR_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
+#define LP_RNPR_TOGGLE 0x0800 /* Toggles between exchanges
+ * of different NP
+ */
+#define LP_RNPR_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg
+ * 0 = cannot comply with msg
+ */
+#define LP_RNPR_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */
+#define LP_RNPR_ACKNOWLDGE 0x4000 /* 1 = ACK / 0 = NO ACK */
+#define LP_RNPR_NEXT_PAGE 0x8000 /* 1 = addition NP will follow
+ * 0 = sending last NP
+ */
+
+/* 1000BASE-T Control Register */
+#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */
+#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
+#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
+#define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */
+ /* 0=DTE device */
+#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
+ /* 0=Configure PHY as Slave */
+#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
+ /* 0=Automatic Master/Slave config */
+#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */
+#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */
+#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */
+#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */
+#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */
+
+/* 1000BASE-T Status Register */
+#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */
+#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */
+#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */
+#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */
+#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
+#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
+#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master, 0=Slave */
+#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */
+#define SR_1000T_REMOTE_RX_STATUS_SHIFT 12
+#define SR_1000T_LOCAL_RX_STATUS_SHIFT 13
+#define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT 5
+#define FFE_IDLE_ERR_COUNT_TIMEOUT_20 20
+#define FFE_IDLE_ERR_COUNT_TIMEOUT_100 100
+
+/* Extended Status Register */
+#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */
+#define IEEE_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */
+#define IEEE_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */
+#define IEEE_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */
+
+#define PHY_TX_POLARITY_MASK 0x0100 /* register 10h bit 8 (polarity bit) */
+#define PHY_TX_NORMAL_POLARITY 0 /* register 10h bit 8 (normal polarity) */
+
+#define AUTO_POLARITY_DISABLE 0x0010 /* register 11h bit 4 */
+ /* (0=enable, 1=disable) */
+
+/* M88E1000 PHY Specific Control Register */
+#define M88E1000_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */
+#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
+#define M88E1000_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */
+#define M88E1000_PSCR_CLK125_DISABLE 0x0010 /* 1=CLK125 low,
+ * 0=CLK125 toggling
+ */
+#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
+ /* Manual MDI configuration */
+#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
+#define M88E1000_PSCR_AUTO_X_1000T 0x0040 /* 1000BASE-T: Auto crossover,
+ * 100BASE-TX/10BASE-T:
+ * MDI Mode
+ */
+#define M88E1000_PSCR_AUTO_X_MODE 0x0060 /* Auto crossover enabled
+ * all speeds.
+ */
+#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE 0x0080
+ /* 1=Enable Extended 10BASE-T distance
+ * (Lower 10BASE-T RX Threshold)
+ * 0=Normal 10BASE-T RX Threshold */
+#define M88E1000_PSCR_MII_5BIT_ENABLE 0x0100
+ /* 1=5-Bit interface in 100BASE-TX
+ * 0=MII interface in 100BASE-TX */
+#define M88E1000_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */
+#define M88E1000_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */
+#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
+
+#define M88E1000_PSCR_POLARITY_REVERSAL_SHIFT 1
+#define M88E1000_PSCR_AUTO_X_MODE_SHIFT 5
+#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT 7
+
+/* M88E1000 PHY Specific Status Register */
+#define M88E1000_PSSR_JABBER 0x0001 /* 1=Jabber */
+#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
+#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
+#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
+#define M88E1000_PSSR_CABLE_LENGTH 0x0380 /* 0=<50M;1=50-80M;2=80-110M;
+ * 3=110-140M;4=>140M */
+#define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */
+#define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */
+#define M88E1000_PSSR_PAGE_RCVD 0x1000 /* 1=Page received */
+#define M88E1000_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */
+#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
+#define M88E1000_PSSR_10MBS 0x0000 /* 00=10Mbs */
+#define M88E1000_PSSR_100MBS 0x4000 /* 01=100Mbs */
+#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
+
+#define M88E1000_PSSR_REV_POLARITY_SHIFT 1
+#define M88E1000_PSSR_DOWNSHIFT_SHIFT 5
+#define M88E1000_PSSR_MDIX_SHIFT 6
+#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
+
+/* M88E1000 Extended PHY Specific Control Register */
+#define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */
+#define M88E1000_EPSCR_DOWN_NO_IDLE 0x8000 /* 1=Lost lock detect enabled.
+ * Will assert lost lock and bring
+ * link down if idle not seen
+ * within 1ms in 1000BASE-T
+ */
+/* Number of times we will attempt to autonegotiate before downshifting if we
+ * are the master */
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_2X 0x0400
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_3X 0x0800
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_4X 0x0C00
+/* Number of times we will attempt to autonegotiate before downshifting if we
+ * are the slave */
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_DIS 0x0000
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_2X 0x0200
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_3X 0x0300
+#define M88E1000_EPSCR_TX_CLK_2_5 0x0060 /* 2.5 MHz TX_CLK */
+#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
+#define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */
+
+/* M88EC018 Rev 2 specific DownShift settings */
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_1X 0x0000
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_2X 0x0200
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_3X 0x0400
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_4X 0x0600
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_6X 0x0A00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_7X 0x0C00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_8X 0x0E00
+
+/* IGP01E1000 Specific Port Config Register - R/W */
+#define IGP01E1000_PSCFR_AUTO_MDIX_PAR_DETECT 0x0010
+#define IGP01E1000_PSCFR_PRE_EN 0x0020
+#define IGP01E1000_PSCFR_SMART_SPEED 0x0080
+#define IGP01E1000_PSCFR_DISABLE_TPLOOPBACK 0x0100
+#define IGP01E1000_PSCFR_DISABLE_JABBER 0x0400
+#define IGP01E1000_PSCFR_DISABLE_TRANSMIT 0x2000
+
+/* IGP01E1000 Specific Port Status Register - R/O */
+#define IGP01E1000_PSSR_AUTONEG_FAILED 0x0001 /* RO LH SC */
+#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002
+#define IGP01E1000_PSSR_CABLE_LENGTH 0x007C
+#define IGP01E1000_PSSR_FULL_DUPLEX 0x0200
+#define IGP01E1000_PSSR_LINK_UP 0x0400
+#define IGP01E1000_PSSR_MDIX 0x0800
+#define IGP01E1000_PSSR_SPEED_MASK 0xC000 /* speed bits mask */
+#define IGP01E1000_PSSR_SPEED_10MBPS 0x4000
+#define IGP01E1000_PSSR_SPEED_100MBPS 0x8000
+#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000
+#define IGP01E1000_PSSR_CABLE_LENGTH_SHIFT 0x0002 /* shift right 2 */
+#define IGP01E1000_PSSR_MDIX_SHIFT 0x000B /* shift right 11 */
+
+/* IGP01E1000 Specific Port Control Register - R/W */
+#define IGP01E1000_PSCR_TP_LOOPBACK 0x0010
+#define IGP01E1000_PSCR_CORRECT_NC_SCMBLR 0x0200
+#define IGP01E1000_PSCR_TEN_CRS_SELECT 0x0400
+#define IGP01E1000_PSCR_FLIP_CHIP 0x0800
+#define IGP01E1000_PSCR_AUTO_MDIX 0x1000
+#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0-MDI, 1-MDIX */
+
+/* IGP01E1000 Specific Port Link Health Register */
+#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000
+#define IGP01E1000_PLHR_GIG_SCRAMBLER_ERROR 0x4000
+#define IGP01E1000_PLHR_MASTER_FAULT 0x2000
+#define IGP01E1000_PLHR_MASTER_RESOLUTION 0x1000
+#define IGP01E1000_PLHR_GIG_REM_RCVR_NOK 0x0800 /* LH */
+#define IGP01E1000_PLHR_IDLE_ERROR_CNT_OFLOW 0x0400 /* LH */
+#define IGP01E1000_PLHR_DATA_ERR_1 0x0200 /* LH */
+#define IGP01E1000_PLHR_DATA_ERR_0 0x0100
+#define IGP01E1000_PLHR_AUTONEG_FAULT 0x0040
+#define IGP01E1000_PLHR_AUTONEG_ACTIVE 0x0010
+#define IGP01E1000_PLHR_VALID_CHANNEL_D 0x0008
+#define IGP01E1000_PLHR_VALID_CHANNEL_C 0x0004
+#define IGP01E1000_PLHR_VALID_CHANNEL_B 0x0002
+#define IGP01E1000_PLHR_VALID_CHANNEL_A 0x0001
+
+/* IGP01E1000 Channel Quality Register */
+#define IGP01E1000_MSE_CHANNEL_D 0x000F
+#define IGP01E1000_MSE_CHANNEL_C 0x00F0
+#define IGP01E1000_MSE_CHANNEL_B 0x0F00
+#define IGP01E1000_MSE_CHANNEL_A 0xF000
+
+#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */
+#define IGP02E1000_PM_D3_LPLU 0x0004 /* Enable LPLU in non-D0a modes */
+#define IGP02E1000_PM_D0_LPLU 0x0002 /* Enable LPLU in D0a mode */
+
+/* IGP01E1000 DSP reset macros */
+#define DSP_RESET_ENABLE 0x0
+#define DSP_RESET_DISABLE 0x2
+#define E1000_MAX_DSP_RESETS 10
+
+/* IGP01E1000 & IGP02E1000 AGC Registers */
+
+#define IGP01E1000_AGC_LENGTH_SHIFT 7 /* Coarse - 13:11, Fine - 10:7 */
+#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Coarse - 15:13, Fine - 12:9 */
+
+/* IGP02E1000 AGC Register Length 9-bit mask */
+#define IGP02E1000_AGC_LENGTH_MASK 0x7F
+
+/* 7 bits (3 Coarse + 4 Fine) --> 128 optional values */
+#define IGP01E1000_AGC_LENGTH_TABLE_SIZE 128
+#define IGP02E1000_AGC_LENGTH_TABLE_SIZE 113
+
+/* The precision error of the cable length is +/- 10 meters */
+#define IGP01E1000_AGC_RANGE 10
+#define IGP02E1000_AGC_RANGE 15
+
+/* IGP01E1000 PCS Initialization register */
+/* bits 3:6 in the PCS registers stores the channels polarity */
+#define IGP01E1000_PHY_POLARITY_MASK 0x0078
+
+/* IGP01E1000 GMII FIFO Register */
+#define IGP01E1000_GMII_FLEX_SPD 0x10 /* Enable flexible speed
+ * on Link-Up */
+#define IGP01E1000_GMII_SPD 0x20 /* Enable SPD */
+
+/* IGP01E1000 Analog Register */
+#define IGP01E1000_ANALOG_SPARE_FUSE_STATUS 0x20D1
+#define IGP01E1000_ANALOG_FUSE_STATUS 0x20D0
+#define IGP01E1000_ANALOG_FUSE_CONTROL 0x20DC
+#define IGP01E1000_ANALOG_FUSE_BYPASS 0x20DE
+
+#define IGP01E1000_ANALOG_FUSE_POLY_MASK 0xF000
+#define IGP01E1000_ANALOG_FUSE_FINE_MASK 0x0F80
+#define IGP01E1000_ANALOG_FUSE_COARSE_MASK 0x0070
+#define IGP01E1000_ANALOG_SPARE_FUSE_ENABLED 0x0100
+#define IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL 0x0002
+
+#define IGP01E1000_ANALOG_FUSE_COARSE_THRESH 0x0040
+#define IGP01E1000_ANALOG_FUSE_COARSE_10 0x0010
+#define IGP01E1000_ANALOG_FUSE_FINE_1 0x0080
+#define IGP01E1000_ANALOG_FUSE_FINE_10 0x0500
+
+/* Bit definitions for valid PHY IDs. */
+/* I = Integrated
+ * E = External
+ */
+#define M88_VENDOR 0x0141
+#define M88E1000_E_PHY_ID 0x01410C50
+#define M88E1000_I_PHY_ID 0x01410C30
+#define M88E1011_I_PHY_ID 0x01410C20
+#define IGP01E1000_I_PHY_ID 0x02A80380
+#define M88E1000_12_PHY_ID M88E1000_E_PHY_ID
+#define M88E1000_14_PHY_ID M88E1000_E_PHY_ID
+#define M88E1011_I_REV_4 0x04
+#define M88E1111_I_PHY_ID 0x01410CC0
+#define L1LXT971A_PHY_ID 0x001378E0
+
+/* Bits...
+ * 15-5: page
+ * 4-0: register offset
+ */
+#define PHY_PAGE_SHIFT 5
+#define PHY_REG(page, reg) \
+ (((page) << PHY_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
+
+#define IGP3_PHY_PORT_CTRL \
+ PHY_REG(769, 17) /* Port General Configuration */
+#define IGP3_PHY_RATE_ADAPT_CTRL \
+ PHY_REG(769, 25) /* Rate Adapter Control Register */
+
+#define IGP3_KMRN_FIFO_CTRL_STATS \
+ PHY_REG(770, 16) /* KMRN FIFO's control/status register */
+#define IGP3_KMRN_POWER_MNG_CTRL \
+ PHY_REG(770, 17) /* KMRN Power Management Control Register */
+#define IGP3_KMRN_INBAND_CTRL \
+ PHY_REG(770, 18) /* KMRN Inband Control Register */
+#define IGP3_KMRN_DIAG \
+ PHY_REG(770, 19) /* KMRN Diagnostic register */
+#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 /* RX PCS is not synced */
+#define IGP3_KMRN_ACK_TIMEOUT \
+ PHY_REG(770, 20) /* KMRN Acknowledge Timeouts register */
+
+#define IGP3_VR_CTRL \
+ PHY_REG(776, 18) /* Voltage regulator control register */
+#define IGP3_VR_CTRL_MODE_SHUT 0x0200 /* Enter powerdown, shutdown VRs */
+#define IGP3_VR_CTRL_MODE_MASK 0x0300 /* Shutdown VR Mask */
+
+#define IGP3_CAPABILITY \
+ PHY_REG(776, 19) /* IGP3 Capability Register */
+
+/* Capabilities for SKU Control */
+#define IGP3_CAP_INITIATE_TEAM 0x0001 /* Able to initiate a team */
+#define IGP3_CAP_WFM 0x0002 /* Support WoL and PXE */
+#define IGP3_CAP_ASF 0x0004 /* Support ASF */
+#define IGP3_CAP_LPLU 0x0008 /* Support Low Power Link Up */
+#define IGP3_CAP_DC_AUTO_SPEED 0x0010 /* Support AC/DC Auto Link Speed */
+#define IGP3_CAP_SPD 0x0020 /* Support Smart Power Down */
+#define IGP3_CAP_MULT_QUEUE 0x0040 /* Support 2 tx & 2 rx queues */
+#define IGP3_CAP_RSS 0x0080 /* Support RSS */
+#define IGP3_CAP_8021PQ 0x0100 /* Support 802.1Q & 802.1p */
+#define IGP3_CAP_AMT_CB 0x0200 /* Support active manageability and circuit breaker */
+
+#define IGP3_PPC_JORDAN_EN 0x0001
+#define IGP3_PPC_JORDAN_GIGA_SPEED 0x0002
+
+#define IGP3_KMRN_PMC_EE_IDLE_LINK_DIS 0x0001
+#define IGP3_KMRN_PMC_K0S_ENTRY_LATENCY_MASK 0x001E
+#define IGP3_KMRN_PMC_K0S_MODE1_EN_GIGA 0x0020
+#define IGP3_KMRN_PMC_K0S_MODE1_EN_100 0x0040
+
+#define IGP3E1000_PHY_MISC_CTRL 0x1B /* Misc. Ctrl register */
+#define IGP3_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Duplex Manual Set */
+
+#define IGP3_KMRN_EXT_CTRL PHY_REG(770, 18)
+#define IGP3_KMRN_EC_DIS_INBAND 0x0080
+
+#define IGP03E1000_E_PHY_ID 0x02A80390
+#define IFE_E_PHY_ID 0x02A80330 /* 10/100 PHY */
+#define IFE_PLUS_E_PHY_ID 0x02A80320
+#define IFE_C_E_PHY_ID 0x02A80310
+
+#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 /* 100BaseTx Extended Status, Control and Address */
+#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY special control register */
+#define IFE_PHY_RCV_FALSE_CARRIER 0x13 /* 100BaseTx Receive False Carrier Counter */
+#define IFE_PHY_RCV_DISCONNECT 0x14 /* 100BaseTx Receive Disconnect Counter */
+#define IFE_PHY_RCV_ERROT_FRAME 0x15 /* 100BaseTx Receive Error Frame Counter */
+#define IFE_PHY_RCV_SYMBOL_ERR 0x16 /* Receive Symbol Error Counter */
+#define IFE_PHY_PREM_EOF_ERR 0x17 /* 100BaseTx Receive Premature End Of Frame Error Counter */
+#define IFE_PHY_RCV_EOF_ERR 0x18 /* 10BaseT Receive End Of Frame Error Counter */
+#define IFE_PHY_TX_JABBER_DETECT 0x19 /* 10BaseT Transmit Jabber Detect Counter */
+#define IFE_PHY_EQUALIZER 0x1A /* PHY Equalizer Control and Status */
+#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY special control and LED configuration */
+#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control register */
+#define IFE_PHY_HWI_CONTROL 0x1D /* Hardware Integrity Control (HWI) */
+
+#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE 0x2000 /* Default 1 = Disable auto reduced power down */
+#define IFE_PESC_100BTX_POWER_DOWN 0x0400 /* Indicates the power state of 100BASE-TX */
+#define IFE_PESC_10BTX_POWER_DOWN 0x0200 /* Indicates the power state of 10BASE-T */
+#define IFE_PESC_POLARITY_REVERSED 0x0100 /* Indicates 10BASE-T polarity */
+#define IFE_PESC_PHY_ADDR_MASK 0x007C /* Bit 6:2 for sampled PHY address */
+#define IFE_PESC_SPEED 0x0002 /* Auto-negotiation speed result 1=100Mbs, 0=10Mbs */
+#define IFE_PESC_DUPLEX 0x0001 /* Auto-negotiation duplex result 1=Full, 0=Half */
+#define IFE_PESC_POLARITY_REVERSED_SHIFT 8
+
+#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 /* 1 = Dynamic Power Down disabled */
+#define IFE_PSC_FORCE_POLARITY 0x0020 /* 1=Reversed Polarity, 0=Normal */
+#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 /* 1=Auto Polarity Disabled, 0=Enabled */
+#define IFE_PSC_JABBER_FUNC_DISABLE 0x0001 /* 1=Jabber Disabled, 0=Normal Jabber Operation */
+#define IFE_PSC_FORCE_POLARITY_SHIFT 5
+#define IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT 4
+
+#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable MDI/MDI-X feature, default 0=disabled */
+#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDIX-X, 0=force MDI */
+#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */
+#define IFE_PMC_AUTO_MDIX_COMPLETE 0x0010 /* Resolution algorithm is completed */
+#define IFE_PMC_MDIX_MODE_SHIFT 6
+#define IFE_PHC_MDIX_RESET_ALL_MASK 0x0000 /* Disable auto MDI-X */
+
+#define IFE_PHC_HWI_ENABLE 0x8000 /* Enable the HWI feature */
+#define IFE_PHC_ABILITY_CHECK 0x4000 /* 1= Test Passed, 0=failed */
+#define IFE_PHC_TEST_EXEC 0x2000 /* PHY launch test pulses on the wire */
+#define IFE_PHC_HIGHZ 0x0200 /* 1 = Open Circuit */
+#define IFE_PHC_LOWZ 0x0400 /* 1 = Short Circuit */
+#define IFE_PHC_LOW_HIGH_Z_MASK 0x0600 /* Mask for indication type of problem on the line */
+#define IFE_PHC_DISTANCE_MASK 0x01FF /* Mask for distance to the cable problem, in 80cm granularity */
+#define IFE_PHC_RESET_ALL_MASK 0x0000 /* Disable HWI */
+#define IFE_PSCL_PROBE_MODE 0x0020 /* LED Probe mode */
+#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */
+#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */
+
+#define ICH_FLASH_COMMAND_TIMEOUT 5000 /* 5000 uSecs - adjusted */
+#define ICH_FLASH_ERASE_TIMEOUT 3000000 /* Up to 3 seconds - worst case */
+#define ICH_FLASH_CYCLE_REPEAT_COUNT 10 /* 10 cycles */
+#define ICH_FLASH_SEG_SIZE_256 256
+#define ICH_FLASH_SEG_SIZE_4K 4096
+#define ICH_FLASH_SEG_SIZE_64K 65536
+
+#define ICH_CYCLE_READ 0x0
+#define ICH_CYCLE_RESERVED 0x1
+#define ICH_CYCLE_WRITE 0x2
+#define ICH_CYCLE_ERASE 0x3
+
+#define ICH_FLASH_GFPREG 0x0000
+#define ICH_FLASH_HSFSTS 0x0004
+#define ICH_FLASH_HSFCTL 0x0006
+#define ICH_FLASH_FADDR 0x0008
+#define ICH_FLASH_FDATA0 0x0010
+#define ICH_FLASH_FRACC 0x0050
+#define ICH_FLASH_FREG0 0x0054
+#define ICH_FLASH_FREG1 0x0058
+#define ICH_FLASH_FREG2 0x005C
+#define ICH_FLASH_FREG3 0x0060
+#define ICH_FLASH_FPR0 0x0074
+#define ICH_FLASH_FPR1 0x0078
+#define ICH_FLASH_SSFSTS 0x0090
+#define ICH_FLASH_SSFCTL 0x0092
+#define ICH_FLASH_PREOP 0x0094
+#define ICH_FLASH_OPTYPE 0x0096
+#define ICH_FLASH_OPMENU 0x0098
+
+#define ICH_FLASH_REG_MAPSIZE 0x00A0
+#define ICH_FLASH_SECTOR_SIZE 4096
+#define ICH_GFPREG_BASE_MASK 0x1FFF
+#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
+
+/* Miscellaneous PHY bit definitions. */
+#define PHY_PREAMBLE 0xFFFFFFFF
+#define PHY_SOF 0x01
+#define PHY_OP_READ 0x02
+#define PHY_OP_WRITE 0x01
+#define PHY_TURNAROUND 0x02
+#define PHY_PREAMBLE_SIZE 32
+#define MII_CR_SPEED_1000 0x0040
+#define MII_CR_SPEED_100 0x2000
+#define MII_CR_SPEED_10 0x0000
+#define E1000_PHY_ADDRESS 0x01
+#define PHY_AUTO_NEG_TIME 45 /* 4.5 Seconds */
+#define PHY_FORCE_TIME 20 /* 2.0 Seconds */
+#define PHY_REVISION_MASK 0xFFFFFFF0
+#define DEVICE_SPEED_MASK 0x00000300 /* Device Ctrl Reg Speed Mask */
+#define REG4_SPEED_MASK 0x01E0
+#define REG9_SPEED_MASK 0x0300
+#define ADVERTISE_10_HALF 0x0001
+#define ADVERTISE_10_FULL 0x0002
+#define ADVERTISE_100_HALF 0x0004
+#define ADVERTISE_100_FULL 0x0008
+#define ADVERTISE_1000_HALF 0x0010
+#define ADVERTISE_1000_FULL 0x0020
+#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F /* Everything but 1000-Half */
+#define AUTONEG_ADVERTISE_10_100_ALL 0x000F /* All 10/100 speeds */
+#define AUTONEG_ADVERTISE_10_ALL 0x0003 /* 10Mbps Full & Half speeds */
+
+#endif /* _E1000_HW_H_ */
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_main-2.6.32-ethercat.c Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,4869 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+ vim: noexpandtab
+
+*******************************************************************************/
+
+#include "e1000-2.6.32-ethercat.h"
+#include <net/ip6_checksum.h>
+
+char e1000_driver_name[] = "ec_e1000";
+static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
+#define DRV_VERSION "7.3.21-k5-NAPI"
+const char e1000_driver_version[] = DRV_VERSION;
+static const char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
+
+/* e1000_pci_tbl - PCI Device ID Table
+ *
+ * Last entry must be all 0s
+ *
+ * Macro expands to...
+ * {PCI_DEVICE(PCI_VENDOR_ID_INTEL, device_id)}
+ */
+static struct pci_device_id e1000_pci_tbl[] = {
+ INTEL_E1000_ETHERNET_DEVICE(0x1000),
+ INTEL_E1000_ETHERNET_DEVICE(0x1001),
+ INTEL_E1000_ETHERNET_DEVICE(0x1004),
+ INTEL_E1000_ETHERNET_DEVICE(0x1008),
+ INTEL_E1000_ETHERNET_DEVICE(0x1009),
+ INTEL_E1000_ETHERNET_DEVICE(0x100C),
+ INTEL_E1000_ETHERNET_DEVICE(0x100D),
+ INTEL_E1000_ETHERNET_DEVICE(0x100E),
+ INTEL_E1000_ETHERNET_DEVICE(0x100F),
+ INTEL_E1000_ETHERNET_DEVICE(0x1010),
+ INTEL_E1000_ETHERNET_DEVICE(0x1011),
+ INTEL_E1000_ETHERNET_DEVICE(0x1012),
+ INTEL_E1000_ETHERNET_DEVICE(0x1013),
+ INTEL_E1000_ETHERNET_DEVICE(0x1014),
+ INTEL_E1000_ETHERNET_DEVICE(0x1015),
+ INTEL_E1000_ETHERNET_DEVICE(0x1016),
+ INTEL_E1000_ETHERNET_DEVICE(0x1017),
+ INTEL_E1000_ETHERNET_DEVICE(0x1018),
+ INTEL_E1000_ETHERNET_DEVICE(0x1019),
+ INTEL_E1000_ETHERNET_DEVICE(0x101A),
+ INTEL_E1000_ETHERNET_DEVICE(0x101D),
+ INTEL_E1000_ETHERNET_DEVICE(0x101E),
+ INTEL_E1000_ETHERNET_DEVICE(0x1026),
+ INTEL_E1000_ETHERNET_DEVICE(0x1027),
+ INTEL_E1000_ETHERNET_DEVICE(0x1028),
+ INTEL_E1000_ETHERNET_DEVICE(0x1075),
+ INTEL_E1000_ETHERNET_DEVICE(0x1076),
+ INTEL_E1000_ETHERNET_DEVICE(0x1077),
+ INTEL_E1000_ETHERNET_DEVICE(0x1078),
+ INTEL_E1000_ETHERNET_DEVICE(0x1079),
+ INTEL_E1000_ETHERNET_DEVICE(0x107A),
+ INTEL_E1000_ETHERNET_DEVICE(0x107B),
+ INTEL_E1000_ETHERNET_DEVICE(0x107C),
+ INTEL_E1000_ETHERNET_DEVICE(0x108A),
+ INTEL_E1000_ETHERNET_DEVICE(0x1099),
+ INTEL_E1000_ETHERNET_DEVICE(0x10B5),
+ /* required last entry */
+ {0,}
+};
+
+// do not auto-load driver
+// MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
+
+int e1000_up(struct e1000_adapter *adapter);
+void e1000_down(struct e1000_adapter *adapter);
+void e1000_reinit_locked(struct e1000_adapter *adapter);
+void e1000_reset(struct e1000_adapter *adapter);
+int e1000_set_spd_dplx(struct e1000_adapter *adapter, u16 spddplx);
+int e1000_setup_all_tx_resources(struct e1000_adapter *adapter);
+int e1000_setup_all_rx_resources(struct e1000_adapter *adapter);
+void e1000_free_all_tx_resources(struct e1000_adapter *adapter);
+void e1000_free_all_rx_resources(struct e1000_adapter *adapter);
+static int e1000_setup_tx_resources(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *txdr);
+static int e1000_setup_rx_resources(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rxdr);
+static void e1000_free_tx_resources(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring);
+static void e1000_free_rx_resources(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring);
+void e1000_update_stats(struct e1000_adapter *adapter);
+
+static int e1000_init_module(void);
+static void e1000_exit_module(void);
+static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent);
+static void __devexit e1000_remove(struct pci_dev *pdev);
+static int e1000_alloc_queues(struct e1000_adapter *adapter);
+static int e1000_sw_init(struct e1000_adapter *adapter);
+static int e1000_open(struct net_device *netdev);
+static int e1000_close(struct net_device *netdev);
+static void e1000_configure_tx(struct e1000_adapter *adapter);
+static void e1000_configure_rx(struct e1000_adapter *adapter);
+static void e1000_setup_rctl(struct e1000_adapter *adapter);
+static void e1000_clean_all_tx_rings(struct e1000_adapter *adapter);
+static void e1000_clean_all_rx_rings(struct e1000_adapter *adapter);
+static void e1000_clean_tx_ring(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring);
+static void e1000_clean_rx_ring(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring);
+static void e1000_set_rx_mode(struct net_device *netdev);
+static void e1000_update_phy_info(unsigned long data);
+static void e1000_watchdog(unsigned long data);
+static void e1000_82547_tx_fifo_stall(unsigned long data);
+static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
+ struct net_device *netdev);
+static struct net_device_stats * e1000_get_stats(struct net_device *netdev);
+static int e1000_change_mtu(struct net_device *netdev, int new_mtu);
+static int e1000_set_mac(struct net_device *netdev, void *p);
+void ec_poll(struct net_device *);
+static irqreturn_t e1000_intr(int irq, void *data);
+static bool e1000_clean_tx_irq(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring);
+static int e1000_clean(struct napi_struct *napi, int budget);
+static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int *work_done, int work_to_do);
+static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int *work_done, int work_to_do);
+static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int cleaned_count);
+static void e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int cleaned_count);
+static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd);
+static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
+ int cmd);
+static void e1000_enter_82542_rst(struct e1000_adapter *adapter);
+static void e1000_leave_82542_rst(struct e1000_adapter *adapter);
+static void e1000_tx_timeout(struct net_device *dev);
+static void e1000_reset_task(struct work_struct *work);
+static void e1000_smartspeed(struct e1000_adapter *adapter);
+static int e1000_82547_fifo_workaround(struct e1000_adapter *adapter,
+ struct sk_buff *skb);
+
+static void e1000_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp);
+static void e1000_vlan_rx_add_vid(struct net_device *netdev, u16 vid);
+static void e1000_vlan_rx_kill_vid(struct net_device *netdev, u16 vid);
+static void e1000_restore_vlan(struct e1000_adapter *adapter);
+
+#ifdef CONFIG_PM
+static int e1000_suspend(struct pci_dev *pdev, pm_message_t state);
+static int e1000_resume(struct pci_dev *pdev);
+#endif
+static void e1000_shutdown(struct pci_dev *pdev);
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+/* for netdump / net console */
+static void e1000_netpoll (struct net_device *netdev);
+#endif
+
+#define COPYBREAK_DEFAULT 256
+static unsigned int copybreak __read_mostly = COPYBREAK_DEFAULT;
+module_param(copybreak, uint, 0644);
+MODULE_PARM_DESC(copybreak,
+ "Maximum size of packet that is copied to a new buffer on receive");
+
+static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
+ pci_channel_state_t state);
+static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev);
+static void e1000_io_resume(struct pci_dev *pdev);
+
+static struct pci_error_handlers e1000_err_handler = {
+ .error_detected = e1000_io_error_detected,
+ .slot_reset = e1000_io_slot_reset,
+ .resume = e1000_io_resume,
+};
+
+static struct pci_driver e1000_driver = {
+ .name = e1000_driver_name,
+ .id_table = e1000_pci_tbl,
+ .probe = e1000_probe,
+ .remove = __devexit_p(e1000_remove),
+#ifdef CONFIG_PM
+ /* Power Managment Hooks */
+ .suspend = e1000_suspend,
+ .resume = e1000_resume,
+#endif
+ .shutdown = e1000_shutdown,
+ .err_handler = &e1000_err_handler
+};
+
+MODULE_AUTHOR("Florian Pose <fp@igh-essen.com>");
+MODULE_DESCRIPTION("EtherCAT-capable Intel(R) PRO/1000 Network Driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+static int debug = NETIF_MSG_DRV | NETIF_MSG_PROBE;
+module_param(debug, int, 0);
+MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
+
+/**
+ * e1000_init_module - Driver Registration Routine
+ *
+ * e1000_init_module is the first routine called when the driver is
+ * loaded. All it does is register with the PCI subsystem.
+ **/
+
+static int __init e1000_init_module(void)
+{
+ int ret;
+ printk(KERN_INFO "%s - version %s\n",
+ e1000_driver_string, e1000_driver_version);
+
+ printk(KERN_INFO "%s\n", e1000_copyright);
+
+ ret = pci_register_driver(&e1000_driver);
+ if (copybreak != COPYBREAK_DEFAULT) {
+ if (copybreak == 0)
+ printk(KERN_INFO "e1000: copybreak disabled\n");
+ else
+ printk(KERN_INFO "e1000: copybreak enabled for "
+ "packets <= %u bytes\n", copybreak);
+ }
+ return ret;
+}
+
+module_init(e1000_init_module);
+
+/**
+ * e1000_exit_module - Driver Exit Cleanup Routine
+ *
+ * e1000_exit_module is called just before the driver is removed
+ * from memory.
+ **/
+
+static void __exit e1000_exit_module(void)
+{
+ pci_unregister_driver(&e1000_driver);
+}
+
+module_exit(e1000_exit_module);
+
+static int e1000_request_irq(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ irq_handler_t handler = e1000_intr;
+ int irq_flags = IRQF_SHARED;
+ int err;
+
+ if (adapter->ecdev)
+ return 0;
+
+ err = request_irq(adapter->pdev->irq, handler, irq_flags, netdev->name,
+ netdev);
+ if (err) {
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate interrupt Error: %d\n", err);
+ }
+
+ return err;
+}
+
+static void e1000_free_irq(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+
+ if (adapter->ecdev)
+ return;
+
+ free_irq(adapter->pdev->irq, netdev);
+}
+
+/**
+ * e1000_irq_disable - Mask off interrupt generation on the NIC
+ * @adapter: board private structure
+ **/
+
+static void e1000_irq_disable(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (adapter->ecdev)
+ return;
+
+ ew32(IMC, ~0);
+ E1000_WRITE_FLUSH();
+ synchronize_irq(adapter->pdev->irq);
+}
+
+/**
+ * e1000_irq_enable - Enable default interrupt generation settings
+ * @adapter: board private structure
+ **/
+
+static void e1000_irq_enable(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (adapter->ecdev)
+ return;
+
+ ew32(IMS, IMS_ENABLE_MASK);
+ E1000_WRITE_FLUSH();
+}
+
+static void e1000_update_mng_vlan(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u16 vid = hw->mng_cookie.vlan_id;
+ u16 old_vid = adapter->mng_vlan_id;
+ if (adapter->vlgrp) {
+ if (!vlan_group_get_device(adapter->vlgrp, vid)) {
+ if (hw->mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) {
+ e1000_vlan_rx_add_vid(netdev, vid);
+ adapter->mng_vlan_id = vid;
+ } else
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+
+ if ((old_vid != (u16)E1000_MNG_VLAN_NONE) &&
+ (vid != old_vid) &&
+ !vlan_group_get_device(adapter->vlgrp, old_vid))
+ e1000_vlan_rx_kill_vid(netdev, old_vid);
+ } else
+ adapter->mng_vlan_id = vid;
+ }
+}
+
+static void e1000_init_manageability(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (adapter->en_mng_pt) {
+ u32 manc = er32(MANC);
+
+ /* disable hardware interception of ARP */
+ manc &= ~(E1000_MANC_ARP_EN);
+
+ ew32(MANC, manc);
+ }
+}
+
+static void e1000_release_manageability(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (adapter->en_mng_pt) {
+ u32 manc = er32(MANC);
+
+ /* re-enable hardware interception of ARP */
+ manc |= E1000_MANC_ARP_EN;
+
+ ew32(MANC, manc);
+ }
+}
+
+/**
+ * e1000_configure - configure the hardware for RX and TX
+ * @adapter = private board structure
+ **/
+static void e1000_configure(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ int i;
+
+ e1000_set_rx_mode(netdev);
+
+ e1000_restore_vlan(adapter);
+ e1000_init_manageability(adapter);
+
+ e1000_configure_tx(adapter);
+ e1000_setup_rctl(adapter);
+ e1000_configure_rx(adapter);
+ /* call E1000_DESC_UNUSED which always leaves
+ * at least 1 descriptor unused to make sure
+ * next_to_use != next_to_clean */
+ for (i = 0; i < adapter->num_rx_queues; i++) {
+ struct e1000_rx_ring *ring = &adapter->rx_ring[i];
+ if (adapter->ecdev) {
+ /* fill rx ring completely! */
+ adapter->alloc_rx_buf(adapter, ring, ring->count);
+ } else {
+ /* this one leaves the last ring element unallocated! */
+ adapter->alloc_rx_buf(adapter, ring,
+ E1000_DESC_UNUSED(ring));
+ }
+ }
+
+ adapter->tx_queue_len = netdev->tx_queue_len;
+}
+
+int e1000_up(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ /* hardware has been reset, we need to reload some things */
+ e1000_configure(adapter);
+
+ clear_bit(__E1000_DOWN, &adapter->flags);
+
+ if (!adapter->ecdev) {
+ napi_enable(&adapter->napi);
+
+ e1000_irq_enable(adapter);
+
+ netif_wake_queue(adapter->netdev);
+
+ /* fire a link change interrupt to start the watchdog */
+ ew32(ICS, E1000_ICS_LSC);
+ }
+ return 0;
+}
+
+/**
+ * e1000_power_up_phy - restore link in case the phy was powered down
+ * @adapter: address of board private structure
+ *
+ * The phy may be powered down to save power and turn off link when the
+ * driver is unloaded and wake on lan is not enabled (among others)
+ * *** this routine MUST be followed by a call to e1000_reset ***
+ *
+ **/
+
+void e1000_power_up_phy(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 mii_reg = 0;
+
+ /* Just clear the power down bit to wake the phy back up */
+ if (hw->media_type == e1000_media_type_copper) {
+ /* according to the manual, the phy will retain its
+ * settings across a power-down/up cycle */
+ e1000_read_phy_reg(hw, PHY_CTRL, &mii_reg);
+ mii_reg &= ~MII_CR_POWER_DOWN;
+ e1000_write_phy_reg(hw, PHY_CTRL, mii_reg);
+ }
+}
+
+static void e1000_power_down_phy(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ /* Power down the PHY so no link is implied when interface is down *
+ * The PHY cannot be powered down if any of the following is true *
+ * (a) WoL is enabled
+ * (b) AMT is active
+ * (c) SoL/IDER session is active */
+ if (!adapter->wol && hw->mac_type >= e1000_82540 &&
+ hw->media_type == e1000_media_type_copper) {
+ u16 mii_reg = 0;
+
+ switch (hw->mac_type) {
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ if (er32(MANC) & E1000_MANC_SMBUS_EN)
+ goto out;
+ break;
+ default:
+ goto out;
+ }
+ e1000_read_phy_reg(hw, PHY_CTRL, &mii_reg);
+ mii_reg |= MII_CR_POWER_DOWN;
+ e1000_write_phy_reg(hw, PHY_CTRL, mii_reg);
+ mdelay(1);
+ }
+out:
+ return;
+}
+
+void e1000_down(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u32 rctl, tctl;
+
+ /* signal that we're down so the interrupt handler does not
+ * reschedule our watchdog timer */
+ set_bit(__E1000_DOWN, &adapter->flags);
+
+ /* disable receives in the hardware */
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+
+ if (!adapter->ecdev) {
+ /* flush and sleep below */
+ netif_tx_disable(netdev);
+ }
+
+ /* disable transmits in the hardware */
+ tctl = er32(TCTL);
+ tctl &= ~E1000_TCTL_EN;
+ ew32(TCTL, tctl);
+ /* flush both disables and wait for them to finish */
+ E1000_WRITE_FLUSH();
+ msleep(10);
+
+ if (!adapter->ecdev) {
+ napi_disable(&adapter->napi);
+
+ e1000_irq_disable(adapter);
+
+ del_timer_sync(&adapter->tx_fifo_stall_timer);
+ del_timer_sync(&adapter->watchdog_timer);
+ del_timer_sync(&adapter->phy_info_timer);
+ }
+
+ netdev->tx_queue_len = adapter->tx_queue_len;
+ adapter->link_speed = 0;
+ adapter->link_duplex = 0;
+ if (!adapter->ecdev) {
+ netif_carrier_off(netdev);
+ }
+
+ e1000_reset(adapter);
+ e1000_clean_all_tx_rings(adapter);
+ e1000_clean_all_rx_rings(adapter);
+}
+
+void e1000_reinit_locked(struct e1000_adapter *adapter)
+{
+ WARN_ON(in_interrupt());
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+ e1000_down(adapter);
+ e1000_up(adapter);
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+}
+
+void e1000_reset(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 pba = 0, tx_space, min_tx_space, min_rx_space;
+ bool legacy_pba_adjust = false;
+ u16 hwm;
+
+ /* Repartition Pba for greater than 9k mtu
+ * To take effect CTRL.RST is required.
+ */
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ case e1000_82540:
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ legacy_pba_adjust = true;
+ pba = E1000_PBA_48K;
+ break;
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ pba = E1000_PBA_48K;
+ break;
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ legacy_pba_adjust = true;
+ pba = E1000_PBA_30K;
+ break;
+ case e1000_undefined:
+ case e1000_num_macs:
+ break;
+ }
+
+ if (legacy_pba_adjust) {
+ if (hw->max_frame_size > E1000_RXBUFFER_8192)
+ pba -= 8; /* allocate more FIFO for Tx */
+
+ if (hw->mac_type == e1000_82547) {
+ adapter->tx_fifo_head = 0;
+ adapter->tx_head_addr = pba << E1000_TX_HEAD_ADDR_SHIFT;
+ adapter->tx_fifo_size =
+ (E1000_PBA_40K - pba) << E1000_PBA_BYTES_SHIFT;
+ atomic_set(&adapter->tx_fifo_stall, 0);
+ }
+ } else if (hw->max_frame_size > ETH_FRAME_LEN + ETH_FCS_LEN) {
+ /* adjust PBA for jumbo frames */
+ ew32(PBA, pba);
+
+ /* To maintain wire speed transmits, the Tx FIFO should be
+ * large enough to accommodate two full transmit packets,
+ * rounded up to the next 1KB and expressed in KB. Likewise,
+ * the Rx FIFO should be large enough to accommodate at least
+ * one full receive packet and is similarly rounded up and
+ * expressed in KB. */
+ pba = er32(PBA);
+ /* upper 16 bits has Tx packet buffer allocation size in KB */
+ tx_space = pba >> 16;
+ /* lower 16 bits has Rx packet buffer allocation size in KB */
+ pba &= 0xffff;
+ /*
+ * the tx fifo also stores 16 bytes of information about the tx
+ * but don't include ethernet FCS because hardware appends it
+ */
+ min_tx_space = (hw->max_frame_size +
+ sizeof(struct e1000_tx_desc) -
+ ETH_FCS_LEN) * 2;
+ min_tx_space = ALIGN(min_tx_space, 1024);
+ min_tx_space >>= 10;
+ /* software strips receive CRC, so leave room for it */
+ min_rx_space = hw->max_frame_size;
+ min_rx_space = ALIGN(min_rx_space, 1024);
+ min_rx_space >>= 10;
+
+ /* If current Tx allocation is less than the min Tx FIFO size,
+ * and the min Tx FIFO size is less than the current Rx FIFO
+ * allocation, take space away from current Rx allocation */
+ if (tx_space < min_tx_space &&
+ ((min_tx_space - tx_space) < pba)) {
+ pba = pba - (min_tx_space - tx_space);
+
+ /* PCI/PCIx hardware has PBA alignment constraints */
+ switch (hw->mac_type) {
+ case e1000_82545 ... e1000_82546_rev_3:
+ pba &= ~(E1000_PBA_8K - 1);
+ break;
+ default:
+ break;
+ }
+
+ /* if short on rx space, rx wins and must trump tx
+ * adjustment or use Early Receive if available */
+ if (pba < min_rx_space)
+ pba = min_rx_space;
+ }
+ }
+
+ ew32(PBA, pba);
+
+ /*
+ * flow control settings:
+ * The high water mark must be low enough to fit one full frame
+ * (or the size used for early receive) above it in the Rx FIFO.
+ * Set it to the lower of:
+ * - 90% of the Rx FIFO size, and
+ * - the full Rx FIFO size minus the early receive size (for parts
+ * with ERT support assuming ERT set to E1000_ERT_2048), or
+ * - the full Rx FIFO size minus one full frame
+ */
+ hwm = min(((pba << 10) * 9 / 10),
+ ((pba << 10) - hw->max_frame_size));
+
+ hw->fc_high_water = hwm & 0xFFF8; /* 8-byte granularity */
+ hw->fc_low_water = hw->fc_high_water - 8;
+ hw->fc_pause_time = E1000_FC_PAUSE_TIME;
+ hw->fc_send_xon = 1;
+ hw->fc = hw->original_fc;
+
+ /* Allow time for pending master requests to run */
+ e1000_reset_hw(hw);
+ if (hw->mac_type >= e1000_82544)
+ ew32(WUC, 0);
+
+ if (e1000_init_hw(hw))
+ DPRINTK(PROBE, ERR, "Hardware Error\n");
+ e1000_update_mng_vlan(adapter);
+
+ /* if (adapter->hwflags & HWFLAGS_PHY_PWR_BIT) { */
+ if (hw->mac_type >= e1000_82544 &&
+ hw->autoneg == 1 &&
+ hw->autoneg_advertised == ADVERTISE_1000_FULL) {
+ u32 ctrl = er32(CTRL);
+ /* clear phy power management bit if we are in gig only mode,
+ * which if enabled will attempt negotiation to 100Mb, which
+ * can cause a loss of link at power off or driver unload */
+ ctrl &= ~E1000_CTRL_SWDPIN3;
+ ew32(CTRL, ctrl);
+ }
+
+ /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
+ ew32(VET, ETHERNET_IEEE_VLAN_TYPE);
+
+ e1000_reset_adaptive(hw);
+ e1000_phy_get_info(hw, &adapter->phy_info);
+
+ e1000_release_manageability(adapter);
+}
+
+/**
+ * Dump the eeprom for users having checksum issues
+ **/
+static void e1000_dump_eeprom(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct ethtool_eeprom eeprom;
+ const struct ethtool_ops *ops = netdev->ethtool_ops;
+ u8 *data;
+ int i;
+ u16 csum_old, csum_new = 0;
+
+ eeprom.len = ops->get_eeprom_len(netdev);
+ eeprom.offset = 0;
+
+ data = kmalloc(eeprom.len, GFP_KERNEL);
+ if (!data) {
+ printk(KERN_ERR "Unable to allocate memory to dump EEPROM"
+ " data\n");
+ return;
+ }
+
+ ops->get_eeprom(netdev, &eeprom, data);
+
+ csum_old = (data[EEPROM_CHECKSUM_REG * 2]) +
+ (data[EEPROM_CHECKSUM_REG * 2 + 1] << 8);
+ for (i = 0; i < EEPROM_CHECKSUM_REG * 2; i += 2)
+ csum_new += data[i] + (data[i + 1] << 8);
+ csum_new = EEPROM_SUM - csum_new;
+
+ printk(KERN_ERR "/*********************/\n");
+ printk(KERN_ERR "Current EEPROM Checksum : 0x%04x\n", csum_old);
+ printk(KERN_ERR "Calculated : 0x%04x\n", csum_new);
+
+ printk(KERN_ERR "Offset Values\n");
+ printk(KERN_ERR "======== ======\n");
+ print_hex_dump(KERN_ERR, "", DUMP_PREFIX_OFFSET, 16, 1, data, 128, 0);
+
+ printk(KERN_ERR "Include this output when contacting your support "
+ "provider.\n");
+ printk(KERN_ERR "This is not a software error! Something bad "
+ "happened to your hardware or\n");
+ printk(KERN_ERR "EEPROM image. Ignoring this "
+ "problem could result in further problems,\n");
+ printk(KERN_ERR "possibly loss of data, corruption or system hangs!\n");
+ printk(KERN_ERR "The MAC Address will be reset to 00:00:00:00:00:00, "
+ "which is invalid\n");
+ printk(KERN_ERR "and requires you to set the proper MAC "
+ "address manually before continuing\n");
+ printk(KERN_ERR "to enable this network device.\n");
+ printk(KERN_ERR "Please inspect the EEPROM dump and report the issue "
+ "to your hardware vendor\n");
+ printk(KERN_ERR "or Intel Customer Support.\n");
+ printk(KERN_ERR "/*********************/\n");
+
+ kfree(data);
+}
+
+/**
+ * e1000_is_need_ioport - determine if an adapter needs ioport resources or not
+ * @pdev: PCI device information struct
+ *
+ * Return true if an adapter needs ioport resources
+ **/
+static int e1000_is_need_ioport(struct pci_dev *pdev)
+{
+ switch (pdev->device) {
+ case E1000_DEV_ID_82540EM:
+ case E1000_DEV_ID_82540EM_LOM:
+ case E1000_DEV_ID_82540EP:
+ case E1000_DEV_ID_82540EP_LOM:
+ case E1000_DEV_ID_82540EP_LP:
+ case E1000_DEV_ID_82541EI:
+ case E1000_DEV_ID_82541EI_MOBILE:
+ case E1000_DEV_ID_82541ER:
+ case E1000_DEV_ID_82541ER_LOM:
+ case E1000_DEV_ID_82541GI:
+ case E1000_DEV_ID_82541GI_LF:
+ case E1000_DEV_ID_82541GI_MOBILE:
+ case E1000_DEV_ID_82544EI_COPPER:
+ case E1000_DEV_ID_82544EI_FIBER:
+ case E1000_DEV_ID_82544GC_COPPER:
+ case E1000_DEV_ID_82544GC_LOM:
+ case E1000_DEV_ID_82545EM_COPPER:
+ case E1000_DEV_ID_82545EM_FIBER:
+ case E1000_DEV_ID_82546EB_COPPER:
+ case E1000_DEV_ID_82546EB_FIBER:
+ case E1000_DEV_ID_82546EB_QUAD_COPPER:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static const struct net_device_ops e1000_netdev_ops = {
+ .ndo_open = e1000_open,
+ .ndo_stop = e1000_close,
+ .ndo_start_xmit = e1000_xmit_frame,
+ .ndo_get_stats = e1000_get_stats,
+ .ndo_set_rx_mode = e1000_set_rx_mode,
+ .ndo_set_mac_address = e1000_set_mac,
+ .ndo_tx_timeout = e1000_tx_timeout,
+ .ndo_change_mtu = e1000_change_mtu,
+ .ndo_do_ioctl = e1000_ioctl,
+ .ndo_validate_addr = eth_validate_addr,
+
+ .ndo_vlan_rx_register = e1000_vlan_rx_register,
+ .ndo_vlan_rx_add_vid = e1000_vlan_rx_add_vid,
+ .ndo_vlan_rx_kill_vid = e1000_vlan_rx_kill_vid,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = e1000_netpoll,
+#endif
+};
+
+/**
+ * e1000_probe - Device Initialization Routine
+ * @pdev: PCI device information struct
+ * @ent: entry in e1000_pci_tbl
+ *
+ * Returns 0 on success, negative on failure
+ *
+ * e1000_probe initializes an adapter identified by a pci_dev structure.
+ * The OS initialization, configuring of the adapter private structure,
+ * and a hardware reset occur.
+ **/
+static int __devinit e1000_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct net_device *netdev;
+ struct e1000_adapter *adapter;
+ struct e1000_hw *hw;
+
+ static int cards_found = 0;
+ static int global_quad_port_a = 0; /* global ksp3 port a indication */
+ int i, err, pci_using_dac;
+ u16 eeprom_data = 0;
+ u16 eeprom_apme_mask = E1000_EEPROM_APME;
+ int bars, need_ioport;
+
+ /* do not allocate ioport bars when not needed */
+ need_ioport = e1000_is_need_ioport(pdev);
+ if (need_ioport) {
+ bars = pci_select_bars(pdev, IORESOURCE_MEM | IORESOURCE_IO);
+ err = pci_enable_device(pdev);
+ } else {
+ bars = pci_select_bars(pdev, IORESOURCE_MEM);
+ err = pci_enable_device_mem(pdev);
+ }
+ if (err)
+ return err;
+
+ if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64)) &&
+ !pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64))) {
+ pci_using_dac = 1;
+ } else {
+ err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (err) {
+ err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (err) {
+ E1000_ERR("No usable DMA configuration, "
+ "aborting\n");
+ goto err_dma;
+ }
+ }
+ pci_using_dac = 0;
+ }
+
+ err = pci_request_selected_regions(pdev, bars, e1000_driver_name);
+ if (err)
+ goto err_pci_reg;
+
+ pci_set_master(pdev);
+
+ err = -ENOMEM;
+ netdev = alloc_etherdev(sizeof(struct e1000_adapter));
+ if (!netdev)
+ goto err_alloc_etherdev;
+
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+
+ pci_set_drvdata(pdev, netdev);
+ adapter = netdev_priv(netdev);
+ adapter->netdev = netdev;
+ adapter->pdev = pdev;
+ adapter->msg_enable = (1 << debug) - 1;
+ adapter->bars = bars;
+ adapter->need_ioport = need_ioport;
+
+ hw = &adapter->hw;
+ hw->back = adapter;
+
+ err = -EIO;
+ hw->hw_addr = pci_ioremap_bar(pdev, BAR_0);
+ if (!hw->hw_addr)
+ goto err_ioremap;
+
+ if (adapter->need_ioport) {
+ for (i = BAR_1; i <= BAR_5; i++) {
+ if (pci_resource_len(pdev, i) == 0)
+ continue;
+ if (pci_resource_flags(pdev, i) & IORESOURCE_IO) {
+ hw->io_base = pci_resource_start(pdev, i);
+ break;
+ }
+ }
+ }
+
+ netdev->netdev_ops = &e1000_netdev_ops;
+ e1000_set_ethtool_ops(netdev);
+ netdev->watchdog_timeo = 5 * HZ;
+ netif_napi_add(netdev, &adapter->napi, e1000_clean, 64);
+
+ strncpy(netdev->name, pci_name(pdev), sizeof(netdev->name) - 1);
+
+ adapter->bd_number = cards_found;
+
+ /* setup the private structure */
+
+ err = e1000_sw_init(adapter);
+ if (err)
+ goto err_sw_init;
+
+ err = -EIO;
+
+ if (hw->mac_type >= e1000_82543) {
+ netdev->features = NETIF_F_SG |
+ NETIF_F_HW_CSUM |
+ NETIF_F_HW_VLAN_TX |
+ NETIF_F_HW_VLAN_RX |
+ NETIF_F_HW_VLAN_FILTER;
+ }
+
+ if ((hw->mac_type >= e1000_82544) &&
+ (hw->mac_type != e1000_82547))
+ netdev->features |= NETIF_F_TSO;
+
+ if (pci_using_dac)
+ netdev->features |= NETIF_F_HIGHDMA;
+
+ netdev->vlan_features |= NETIF_F_TSO;
+ netdev->vlan_features |= NETIF_F_HW_CSUM;
+ netdev->vlan_features |= NETIF_F_SG;
+
+ adapter->en_mng_pt = e1000_enable_mng_pass_thru(hw);
+
+ /* initialize eeprom parameters */
+ if (e1000_init_eeprom_params(hw)) {
+ E1000_ERR("EEPROM initialization failed\n");
+ goto err_eeprom;
+ }
+
+ /* before reading the EEPROM, reset the controller to
+ * put the device in a known good starting state */
+
+ e1000_reset_hw(hw);
+
+ /* make sure the EEPROM is good */
+ if (e1000_validate_eeprom_checksum(hw) < 0) {
+ DPRINTK(PROBE, ERR, "The EEPROM Checksum Is Not Valid\n");
+ e1000_dump_eeprom(adapter);
+ /*
+ * set MAC address to all zeroes to invalidate and temporary
+ * disable this device for the user. This blocks regular
+ * traffic while still permitting ethtool ioctls from reaching
+ * the hardware as well as allowing the user to run the
+ * interface after manually setting a hw addr using
+ * `ip set address`
+ */
+ memset(hw->mac_addr, 0, netdev->addr_len);
+ } else {
+ /* copy the MAC address out of the EEPROM */
+ if (e1000_read_mac_addr(hw))
+ DPRINTK(PROBE, ERR, "EEPROM Read Error\n");
+ }
+ /* don't block initalization here due to bad MAC address */
+ memcpy(netdev->dev_addr, hw->mac_addr, netdev->addr_len);
+ memcpy(netdev->perm_addr, hw->mac_addr, netdev->addr_len);
+
+ if (!is_valid_ether_addr(netdev->perm_addr))
+ DPRINTK(PROBE, ERR, "Invalid MAC Address\n");
+
+ e1000_get_bus_info(hw);
+
+ init_timer(&adapter->tx_fifo_stall_timer);
+ adapter->tx_fifo_stall_timer.function = &e1000_82547_tx_fifo_stall;
+ adapter->tx_fifo_stall_timer.data = (unsigned long)adapter;
+
+ init_timer(&adapter->watchdog_timer);
+ adapter->watchdog_timer.function = &e1000_watchdog;
+ adapter->watchdog_timer.data = (unsigned long) adapter;
+
+ init_timer(&adapter->phy_info_timer);
+ adapter->phy_info_timer.function = &e1000_update_phy_info;
+ adapter->phy_info_timer.data = (unsigned long)adapter;
+
+ INIT_WORK(&adapter->reset_task, e1000_reset_task);
+
+ e1000_check_options(adapter);
+
+ /* Initial Wake on LAN setting
+ * If APM wake is enabled in the EEPROM,
+ * enable the ACPI Magic Packet filter
+ */
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ break;
+ case e1000_82544:
+ e1000_read_eeprom(hw,
+ EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
+ eeprom_apme_mask = E1000_EEPROM_82544_APM;
+ break;
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ if (er32(STATUS) & E1000_STATUS_FUNC_1){
+ e1000_read_eeprom(hw,
+ EEPROM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
+ break;
+ }
+ /* Fall Through */
+ default:
+ e1000_read_eeprom(hw,
+ EEPROM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
+ break;
+ }
+ if (eeprom_data & eeprom_apme_mask)
+ adapter->eeprom_wol |= E1000_WUFC_MAG;
+
+ /* now that we have the eeprom settings, apply the special cases
+ * where the eeprom may be wrong or the board simply won't support
+ * wake on lan on a particular port */
+ switch (pdev->device) {
+ case E1000_DEV_ID_82546GB_PCIE:
+ adapter->eeprom_wol = 0;
+ break;
+ case E1000_DEV_ID_82546EB_FIBER:
+ case E1000_DEV_ID_82546GB_FIBER:
+ /* Wake events only supported on port A for dual fiber
+ * regardless of eeprom setting */
+ if (er32(STATUS) & E1000_STATUS_FUNC_1)
+ adapter->eeprom_wol = 0;
+ break;
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ /* if quad port adapter, disable WoL on all but port A */
+ if (global_quad_port_a != 0)
+ adapter->eeprom_wol = 0;
+ else
+ adapter->quad_port_a = 1;
+ /* Reset for multiple quad port adapters */
+ if (++global_quad_port_a == 4)
+ global_quad_port_a = 0;
+ break;
+ }
+
+ /* initialize the wol settings based on the eeprom settings */
+ adapter->wol = adapter->eeprom_wol;
+ device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
+
+ /* print bus type/speed/width info */
+ DPRINTK(PROBE, INFO, "(PCI%s:%s:%s) ",
+ ((hw->bus_type == e1000_bus_type_pcix) ? "-X" : ""),
+ ((hw->bus_speed == e1000_bus_speed_133) ? "133MHz" :
+ (hw->bus_speed == e1000_bus_speed_120) ? "120MHz" :
+ (hw->bus_speed == e1000_bus_speed_100) ? "100MHz" :
+ (hw->bus_speed == e1000_bus_speed_66) ? "66MHz" : "33MHz"),
+ ((hw->bus_width == e1000_bus_width_64) ? "64-bit" : "32-bit"));
+
+ printk("%pM\n", netdev->dev_addr);
+
+ /* reset the hardware with the new settings */
+ e1000_reset(adapter);
+
+ // offer device to EtherCAT master module
+ adapter->ecdev = ecdev_offer(netdev, ec_poll, THIS_MODULE);
+ if (adapter->ecdev) {
+ if (ecdev_open(adapter->ecdev)) {
+ ecdev_withdraw(adapter->ecdev);
+ goto err_register;
+ }
+ } else {
+ strcpy(netdev->name, "eth%d");
+ err = register_netdev(netdev);
+ if (err)
+ goto err_register;
+
+ /* carrier off reporting is important to ethtool even BEFORE open */
+ netif_carrier_off(netdev);
+ }
+
+ DPRINTK(PROBE, INFO, "Intel(R) PRO/1000 Network Connection\n");
+
+ cards_found++;
+ return 0;
+
+err_register:
+err_eeprom:
+ e1000_phy_hw_reset(hw);
+
+ if (hw->flash_address)
+ iounmap(hw->flash_address);
+ kfree(adapter->tx_ring);
+ kfree(adapter->rx_ring);
+err_sw_init:
+ iounmap(hw->hw_addr);
+err_ioremap:
+ free_netdev(netdev);
+err_alloc_etherdev:
+ pci_release_selected_regions(pdev, bars);
+err_pci_reg:
+err_dma:
+ pci_disable_device(pdev);
+ return err;
+}
+
+/**
+ * e1000_remove - Device Removal Routine
+ * @pdev: PCI device information struct
+ *
+ * e1000_remove is called by the PCI subsystem to alert the driver
+ * that it should release a PCI device. The could be caused by a
+ * Hot-Plug event, or because the driver is going to be removed from
+ * memory.
+ **/
+
+static void __devexit e1000_remove(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ set_bit(__E1000_DOWN, &adapter->flags);
+
+ if (!adapter->ecdev) {
+ del_timer_sync(&adapter->tx_fifo_stall_timer);
+ del_timer_sync(&adapter->watchdog_timer);
+ del_timer_sync(&adapter->phy_info_timer);
+ }
+
+ cancel_work_sync(&adapter->reset_task);
+
+ e1000_release_manageability(adapter);
+
+ if (adapter->ecdev) {
+ ecdev_close(adapter->ecdev);
+ ecdev_withdraw(adapter->ecdev);
+ } else {
+ unregister_netdev(netdev);
+ }
+
+ e1000_phy_hw_reset(hw);
+
+ kfree(adapter->tx_ring);
+ kfree(adapter->rx_ring);
+
+ iounmap(hw->hw_addr);
+ if (hw->flash_address)
+ iounmap(hw->flash_address);
+ pci_release_selected_regions(pdev, adapter->bars);
+
+ free_netdev(netdev);
+
+ pci_disable_device(pdev);
+}
+
+/**
+ * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
+ * @adapter: board private structure to initialize
+ *
+ * e1000_sw_init initializes the Adapter private data structure.
+ * Fields are initialized based on PCI device information and
+ * OS network device settings (MTU size).
+ **/
+
+static int __devinit e1000_sw_init(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+
+ /* PCI config space info */
+
+ hw->vendor_id = pdev->vendor;
+ hw->device_id = pdev->device;
+ hw->subsystem_vendor_id = pdev->subsystem_vendor;
+ hw->subsystem_id = pdev->subsystem_device;
+ hw->revision_id = pdev->revision;
+
+ pci_read_config_word(pdev, PCI_COMMAND, &hw->pci_cmd_word);
+
+ adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
+ hw->max_frame_size = netdev->mtu +
+ ENET_HEADER_SIZE + ETHERNET_FCS_SIZE;
+ hw->min_frame_size = MINIMUM_ETHERNET_FRAME_SIZE;
+
+ /* identify the MAC */
+
+ if (e1000_set_mac_type(hw)) {
+ DPRINTK(PROBE, ERR, "Unknown MAC Type\n");
+ return -EIO;
+ }
+
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ hw->phy_init_script = 1;
+ break;
+ }
+
+ e1000_set_media_type(hw);
+
+ hw->wait_autoneg_complete = false;
+ hw->tbi_compatibility_en = true;
+ hw->adaptive_ifs = true;
+
+ /* Copper options */
+
+ if (hw->media_type == e1000_media_type_copper) {
+ hw->mdix = AUTO_ALL_MODES;
+ hw->disable_polarity_correction = false;
+ hw->master_slave = E1000_MASTER_SLAVE;
+ }
+
+ adapter->num_tx_queues = 1;
+ adapter->num_rx_queues = 1;
+
+ if (e1000_alloc_queues(adapter)) {
+ DPRINTK(PROBE, ERR, "Unable to allocate memory for queues\n");
+ return -ENOMEM;
+ }
+
+ /* Explicitly disable IRQ since the NIC can be in any state. */
+ e1000_irq_disable(adapter);
+
+ spin_lock_init(&adapter->stats_lock);
+
+ set_bit(__E1000_DOWN, &adapter->flags);
+
+ return 0;
+}
+
+/**
+ * e1000_alloc_queues - Allocate memory for all rings
+ * @adapter: board private structure to initialize
+ *
+ * We allocate one ring per queue at run-time since we don't know the
+ * number of queues at compile-time.
+ **/
+
+static int __devinit e1000_alloc_queues(struct e1000_adapter *adapter)
+{
+ adapter->tx_ring = kcalloc(adapter->num_tx_queues,
+ sizeof(struct e1000_tx_ring), GFP_KERNEL);
+ if (!adapter->tx_ring)
+ return -ENOMEM;
+
+ adapter->rx_ring = kcalloc(adapter->num_rx_queues,
+ sizeof(struct e1000_rx_ring), GFP_KERNEL);
+ if (!adapter->rx_ring) {
+ kfree(adapter->tx_ring);
+ return -ENOMEM;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_open - Called when a network interface is made active
+ * @netdev: network interface device structure
+ *
+ * Returns 0 on success, negative value on failure
+ *
+ * The open entry point is called when a network interface is made
+ * active by the system (IFF_UP). At this point all resources needed
+ * for transmit and receive operations are allocated, the interrupt
+ * handler is registered with the OS, the watchdog timer is started,
+ * and the stack is notified that the interface is ready.
+ **/
+
+static int e1000_open(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ int err;
+
+ /* disallow open during test */
+ if (test_bit(__E1000_TESTING, &adapter->flags))
+ return -EBUSY;
+
+ netif_carrier_off(netdev);
+
+ /* allocate transmit descriptors */
+ err = e1000_setup_all_tx_resources(adapter);
+ if (err)
+ goto err_setup_tx;
+
+ /* allocate receive descriptors */
+ err = e1000_setup_all_rx_resources(adapter);
+ if (err)
+ goto err_setup_rx;
+
+ e1000_power_up_phy(adapter);
+
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+ if ((hw->mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT)) {
+ e1000_update_mng_vlan(adapter);
+ }
+
+ /* before we allocate an interrupt, we must be ready to handle it.
+ * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
+ * as soon as we call pci_request_irq, so we have to setup our
+ * clean_rx handler before we do so. */
+ e1000_configure(adapter);
+
+ err = e1000_request_irq(adapter);
+ if (err)
+ goto err_req_irq;
+
+ /* From here on the code is the same as e1000_up() */
+ clear_bit(__E1000_DOWN, &adapter->flags);
+
+ napi_enable(&adapter->napi);
+
+ e1000_irq_enable(adapter);
+
+ netif_start_queue(netdev);
+
+ /* fire a link status change interrupt to start the watchdog */
+ ew32(ICS, E1000_ICS_LSC);
+
+ return E1000_SUCCESS;
+
+err_req_irq:
+ e1000_power_down_phy(adapter);
+ e1000_free_all_rx_resources(adapter);
+err_setup_rx:
+ e1000_free_all_tx_resources(adapter);
+err_setup_tx:
+ e1000_reset(adapter);
+
+ return err;
+}
+
+/**
+ * e1000_close - Disables a network interface
+ * @netdev: network interface device structure
+ *
+ * Returns 0, this is not allowed to fail
+ *
+ * The close entry point is called when an interface is de-activated
+ * by the OS. The hardware is still under the drivers control, but
+ * needs to be disabled. A global MAC reset is issued to stop the
+ * hardware, and all transmit and receive resources are freed.
+ **/
+
+static int e1000_close(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
+ e1000_down(adapter);
+ e1000_power_down_phy(adapter);
+ e1000_free_irq(adapter);
+
+ e1000_free_all_tx_resources(adapter);
+ e1000_free_all_rx_resources(adapter);
+
+ /* kill manageability vlan ID if supported, but not if a vlan with
+ * the same ID is registered on the host OS (let 8021q kill it) */
+ if ((hw->mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
+ !(adapter->vlgrp &&
+ vlan_group_get_device(adapter->vlgrp, adapter->mng_vlan_id))) {
+ e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_check_64k_bound - check that memory doesn't cross 64kB boundary
+ * @adapter: address of board private structure
+ * @start: address of beginning of memory
+ * @len: length of memory
+ **/
+static bool e1000_check_64k_bound(struct e1000_adapter *adapter, void *start,
+ unsigned long len)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ unsigned long begin = (unsigned long)start;
+ unsigned long end = begin + len;
+
+ /* First rev 82545 and 82546 need to not allow any memory
+ * write location to cross 64k boundary due to errata 23 */
+ if (hw->mac_type == e1000_82545 ||
+ hw->mac_type == e1000_82546) {
+ return ((begin ^ (end - 1)) >> 16) != 0 ? false : true;
+ }
+
+ return true;
+}
+
+/**
+ * e1000_setup_tx_resources - allocate Tx resources (Descriptors)
+ * @adapter: board private structure
+ * @txdr: tx descriptor ring (for a specific queue) to setup
+ *
+ * Return 0 on success, negative on failure
+ **/
+
+static int e1000_setup_tx_resources(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *txdr)
+{
+ struct pci_dev *pdev = adapter->pdev;
+ int size;
+
+ size = sizeof(struct e1000_buffer) * txdr->count;
+ txdr->buffer_info = vmalloc(size);
+ if (!txdr->buffer_info) {
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate memory for the transmit descriptor ring\n");
+ return -ENOMEM;
+ }
+ memset(txdr->buffer_info, 0, size);
+
+ /* round up to nearest 4K */
+
+ txdr->size = txdr->count * sizeof(struct e1000_tx_desc);
+ txdr->size = ALIGN(txdr->size, 4096);
+
+ txdr->desc = pci_alloc_consistent(pdev, txdr->size, &txdr->dma);
+ if (!txdr->desc) {
+setup_tx_desc_die:
+ vfree(txdr->buffer_info);
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate memory for the transmit descriptor ring\n");
+ return -ENOMEM;
+ }
+
+ /* Fix for errata 23, can't cross 64kB boundary */
+ if (!e1000_check_64k_bound(adapter, txdr->desc, txdr->size)) {
+ void *olddesc = txdr->desc;
+ dma_addr_t olddma = txdr->dma;
+ DPRINTK(TX_ERR, ERR, "txdr align check failed: %u bytes "
+ "at %p\n", txdr->size, txdr->desc);
+ /* Try again, without freeing the previous */
+ txdr->desc = pci_alloc_consistent(pdev, txdr->size, &txdr->dma);
+ /* Failed allocation, critical failure */
+ if (!txdr->desc) {
+ pci_free_consistent(pdev, txdr->size, olddesc, olddma);
+ goto setup_tx_desc_die;
+ }
+
+ if (!e1000_check_64k_bound(adapter, txdr->desc, txdr->size)) {
+ /* give up */
+ pci_free_consistent(pdev, txdr->size, txdr->desc,
+ txdr->dma);
+ pci_free_consistent(pdev, txdr->size, olddesc, olddma);
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate aligned memory "
+ "for the transmit descriptor ring\n");
+ vfree(txdr->buffer_info);
+ return -ENOMEM;
+ } else {
+ /* Free old allocation, new allocation was successful */
+ pci_free_consistent(pdev, txdr->size, olddesc, olddma);
+ }
+ }
+ memset(txdr->desc, 0, txdr->size);
+
+ txdr->next_to_use = 0;
+ txdr->next_to_clean = 0;
+
+ return 0;
+}
+
+/**
+ * e1000_setup_all_tx_resources - wrapper to allocate Tx resources
+ * (Descriptors) for all queues
+ * @adapter: board private structure
+ *
+ * Return 0 on success, negative on failure
+ **/
+
+int e1000_setup_all_tx_resources(struct e1000_adapter *adapter)
+{
+ int i, err = 0;
+
+ for (i = 0; i < adapter->num_tx_queues; i++) {
+ err = e1000_setup_tx_resources(adapter, &adapter->tx_ring[i]);
+ if (err) {
+ DPRINTK(PROBE, ERR,
+ "Allocation for Tx Queue %u failed\n", i);
+ for (i-- ; i >= 0; i--)
+ e1000_free_tx_resources(adapter,
+ &adapter->tx_ring[i]);
+ break;
+ }
+ }
+
+ return err;
+}
+
+/**
+ * e1000_configure_tx - Configure 8254x Transmit Unit after Reset
+ * @adapter: board private structure
+ *
+ * Configure the Tx unit of the MAC after a reset.
+ **/
+
+static void e1000_configure_tx(struct e1000_adapter *adapter)
+{
+ u64 tdba;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 tdlen, tctl, tipg;
+ u32 ipgr1, ipgr2;
+
+ /* Setup the HW Tx Head and Tail descriptor pointers */
+
+ switch (adapter->num_tx_queues) {
+ case 1:
+ default:
+ tdba = adapter->tx_ring[0].dma;
+ tdlen = adapter->tx_ring[0].count *
+ sizeof(struct e1000_tx_desc);
+ ew32(TDLEN, tdlen);
+ ew32(TDBAH, (tdba >> 32));
+ ew32(TDBAL, (tdba & 0x00000000ffffffffULL));
+ ew32(TDT, 0);
+ ew32(TDH, 0);
+ adapter->tx_ring[0].tdh = ((hw->mac_type >= e1000_82543) ? E1000_TDH : E1000_82542_TDH);
+ adapter->tx_ring[0].tdt = ((hw->mac_type >= e1000_82543) ? E1000_TDT : E1000_82542_TDT);
+ break;
+ }
+
+ /* Set the default values for the Tx Inter Packet Gap timer */
+ if ((hw->media_type == e1000_media_type_fiber ||
+ hw->media_type == e1000_media_type_internal_serdes))
+ tipg = DEFAULT_82543_TIPG_IPGT_FIBER;
+ else
+ tipg = DEFAULT_82543_TIPG_IPGT_COPPER;
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ tipg = DEFAULT_82542_TIPG_IPGT;
+ ipgr1 = DEFAULT_82542_TIPG_IPGR1;
+ ipgr2 = DEFAULT_82542_TIPG_IPGR2;
+ break;
+ default:
+ ipgr1 = DEFAULT_82543_TIPG_IPGR1;
+ ipgr2 = DEFAULT_82543_TIPG_IPGR2;
+ break;
+ }
+ tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT;
+ tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT;
+ ew32(TIPG, tipg);
+
+ /* Set the Tx Interrupt Delay register */
+
+ ew32(TIDV, adapter->tx_int_delay);
+ if (hw->mac_type >= e1000_82540)
+ ew32(TADV, adapter->tx_abs_int_delay);
+
+ /* Program the Transmit Control Register */
+
+ tctl = er32(TCTL);
+ tctl &= ~E1000_TCTL_CT;
+ tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC |
+ (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
+
+ e1000_config_collision_dist(hw);
+
+ /* Setup Transmit Descriptor Settings for eop descriptor */
+ adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
+
+ /* only set IDE if we are delaying interrupts using the timers */
+ if (adapter->tx_int_delay)
+ adapter->txd_cmd |= E1000_TXD_CMD_IDE;
+
+ if (hw->mac_type < e1000_82543)
+ adapter->txd_cmd |= E1000_TXD_CMD_RPS;
+ else
+ adapter->txd_cmd |= E1000_TXD_CMD_RS;
+
+ /* Cache if we're 82544 running in PCI-X because we'll
+ * need this to apply a workaround later in the send path. */
+ if (hw->mac_type == e1000_82544 &&
+ hw->bus_type == e1000_bus_type_pcix)
+ adapter->pcix_82544 = 1;
+
+ ew32(TCTL, tctl);
+
+}
+
+/**
+ * e1000_setup_rx_resources - allocate Rx resources (Descriptors)
+ * @adapter: board private structure
+ * @rxdr: rx descriptor ring (for a specific queue) to setup
+ *
+ * Returns 0 on success, negative on failure
+ **/
+
+static int e1000_setup_rx_resources(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rxdr)
+{
+ struct pci_dev *pdev = adapter->pdev;
+ int size, desc_len;
+
+ size = sizeof(struct e1000_buffer) * rxdr->count;
+ rxdr->buffer_info = vmalloc(size);
+ if (!rxdr->buffer_info) {
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate memory for the receive descriptor ring\n");
+ return -ENOMEM;
+ }
+ memset(rxdr->buffer_info, 0, size);
+
+ desc_len = sizeof(struct e1000_rx_desc);
+
+ /* Round up to nearest 4K */
+
+ rxdr->size = rxdr->count * desc_len;
+ rxdr->size = ALIGN(rxdr->size, 4096);
+
+ rxdr->desc = pci_alloc_consistent(pdev, rxdr->size, &rxdr->dma);
+
+ if (!rxdr->desc) {
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate memory for the receive descriptor ring\n");
+setup_rx_desc_die:
+ vfree(rxdr->buffer_info);
+ return -ENOMEM;
+ }
+
+ /* Fix for errata 23, can't cross 64kB boundary */
+ if (!e1000_check_64k_bound(adapter, rxdr->desc, rxdr->size)) {
+ void *olddesc = rxdr->desc;
+ dma_addr_t olddma = rxdr->dma;
+ DPRINTK(RX_ERR, ERR, "rxdr align check failed: %u bytes "
+ "at %p\n", rxdr->size, rxdr->desc);
+ /* Try again, without freeing the previous */
+ rxdr->desc = pci_alloc_consistent(pdev, rxdr->size, &rxdr->dma);
+ /* Failed allocation, critical failure */
+ if (!rxdr->desc) {
+ pci_free_consistent(pdev, rxdr->size, olddesc, olddma);
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate memory "
+ "for the receive descriptor ring\n");
+ goto setup_rx_desc_die;
+ }
+
+ if (!e1000_check_64k_bound(adapter, rxdr->desc, rxdr->size)) {
+ /* give up */
+ pci_free_consistent(pdev, rxdr->size, rxdr->desc,
+ rxdr->dma);
+ pci_free_consistent(pdev, rxdr->size, olddesc, olddma);
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate aligned memory "
+ "for the receive descriptor ring\n");
+ goto setup_rx_desc_die;
+ } else {
+ /* Free old allocation, new allocation was successful */
+ pci_free_consistent(pdev, rxdr->size, olddesc, olddma);
+ }
+ }
+ memset(rxdr->desc, 0, rxdr->size);
+
+ rxdr->next_to_clean = 0;
+ rxdr->next_to_use = 0;
+ rxdr->rx_skb_top = NULL;
+
+ return 0;
+}
+
+/**
+ * e1000_setup_all_rx_resources - wrapper to allocate Rx resources
+ * (Descriptors) for all queues
+ * @adapter: board private structure
+ *
+ * Return 0 on success, negative on failure
+ **/
+
+int e1000_setup_all_rx_resources(struct e1000_adapter *adapter)
+{
+ int i, err = 0;
+
+ for (i = 0; i < adapter->num_rx_queues; i++) {
+ err = e1000_setup_rx_resources(adapter, &adapter->rx_ring[i]);
+ if (err) {
+ DPRINTK(PROBE, ERR,
+ "Allocation for Rx Queue %u failed\n", i);
+ for (i-- ; i >= 0; i--)
+ e1000_free_rx_resources(adapter,
+ &adapter->rx_ring[i]);
+ break;
+ }
+ }
+
+ return err;
+}
+
+/**
+ * e1000_setup_rctl - configure the receive control registers
+ * @adapter: Board private structure
+ **/
+static void e1000_setup_rctl(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl;
+
+ rctl = er32(RCTL);
+
+ rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
+
+ rctl |= E1000_RCTL_EN | E1000_RCTL_BAM |
+ E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
+ (hw->mc_filter_type << E1000_RCTL_MO_SHIFT);
+
+ if (hw->tbi_compatibility_on == 1)
+ rctl |= E1000_RCTL_SBP;
+ else
+ rctl &= ~E1000_RCTL_SBP;
+
+ if (adapter->netdev->mtu <= ETH_DATA_LEN)
+ rctl &= ~E1000_RCTL_LPE;
+ else
+ rctl |= E1000_RCTL_LPE;
+
+ /* Setup buffer sizes */
+ rctl &= ~E1000_RCTL_SZ_4096;
+ rctl |= E1000_RCTL_BSEX;
+ switch (adapter->rx_buffer_len) {
+ case E1000_RXBUFFER_2048:
+ default:
+ rctl |= E1000_RCTL_SZ_2048;
+ rctl &= ~E1000_RCTL_BSEX;
+ break;
+ case E1000_RXBUFFER_4096:
+ rctl |= E1000_RCTL_SZ_4096;
+ break;
+ case E1000_RXBUFFER_8192:
+ rctl |= E1000_RCTL_SZ_8192;
+ break;
+ case E1000_RXBUFFER_16384:
+ rctl |= E1000_RCTL_SZ_16384;
+ break;
+ }
+
+ ew32(RCTL, rctl);
+}
+
+/**
+ * e1000_configure_rx - Configure 8254x Receive Unit after Reset
+ * @adapter: board private structure
+ *
+ * Configure the Rx unit of the MAC after a reset.
+ **/
+
+static void e1000_configure_rx(struct e1000_adapter *adapter)
+{
+ u64 rdba;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rdlen, rctl, rxcsum;
+
+ if (adapter->netdev->mtu > ETH_DATA_LEN) {
+ rdlen = adapter->rx_ring[0].count *
+ sizeof(struct e1000_rx_desc);
+ adapter->clean_rx = e1000_clean_jumbo_rx_irq;
+ adapter->alloc_rx_buf = e1000_alloc_jumbo_rx_buffers;
+ } else {
+ rdlen = adapter->rx_ring[0].count *
+ sizeof(struct e1000_rx_desc);
+ adapter->clean_rx = e1000_clean_rx_irq;
+ adapter->alloc_rx_buf = e1000_alloc_rx_buffers;
+ }
+
+ /* disable receives while setting up the descriptors */
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+
+ /* set the Receive Delay Timer Register */
+ ew32(RDTR, adapter->rx_int_delay);
+
+ if (hw->mac_type >= e1000_82540) {
+ ew32(RADV, adapter->rx_abs_int_delay);
+ if (adapter->itr_setting != 0)
+ ew32(ITR, 1000000000 / (adapter->itr * 256));
+ }
+
+ /* Setup the HW Rx Head and Tail Descriptor Pointers and
+ * the Base and Length of the Rx Descriptor Ring */
+ switch (adapter->num_rx_queues) {
+ case 1:
+ default:
+ rdba = adapter->rx_ring[0].dma;
+ ew32(RDLEN, rdlen);
+ ew32(RDBAH, (rdba >> 32));
+ ew32(RDBAL, (rdba & 0x00000000ffffffffULL));
+ ew32(RDT, 0);
+ ew32(RDH, 0);
+ adapter->rx_ring[0].rdh = ((hw->mac_type >= e1000_82543) ? E1000_RDH : E1000_82542_RDH);
+ adapter->rx_ring[0].rdt = ((hw->mac_type >= e1000_82543) ? E1000_RDT : E1000_82542_RDT);
+ break;
+ }
+
+ /* Enable 82543 Receive Checksum Offload for TCP and UDP */
+ if (hw->mac_type >= e1000_82543) {
+ rxcsum = er32(RXCSUM);
+ if (adapter->rx_csum)
+ rxcsum |= E1000_RXCSUM_TUOFL;
+ else
+ /* don't need to clear IPPCSE as it defaults to 0 */
+ rxcsum &= ~E1000_RXCSUM_TUOFL;
+ ew32(RXCSUM, rxcsum);
+ }
+
+ /* Enable Receives */
+ ew32(RCTL, rctl);
+}
+
+/**
+ * e1000_free_tx_resources - Free Tx Resources per Queue
+ * @adapter: board private structure
+ * @tx_ring: Tx descriptor ring for a specific queue
+ *
+ * Free all transmit software resources
+ **/
+
+static void e1000_free_tx_resources(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring)
+{
+ struct pci_dev *pdev = adapter->pdev;
+
+ e1000_clean_tx_ring(adapter, tx_ring);
+
+ vfree(tx_ring->buffer_info);
+ tx_ring->buffer_info = NULL;
+
+ pci_free_consistent(pdev, tx_ring->size, tx_ring->desc, tx_ring->dma);
+
+ tx_ring->desc = NULL;
+}
+
+/**
+ * e1000_free_all_tx_resources - Free Tx Resources for All Queues
+ * @adapter: board private structure
+ *
+ * Free all transmit software resources
+ **/
+
+void e1000_free_all_tx_resources(struct e1000_adapter *adapter)
+{
+ int i;
+
+ for (i = 0; i < adapter->num_tx_queues; i++)
+ e1000_free_tx_resources(adapter, &adapter->tx_ring[i]);
+}
+
+static void e1000_unmap_and_free_tx_resource(struct e1000_adapter *adapter,
+ struct e1000_buffer *buffer_info)
+{
+ if (adapter->ecdev)
+ return;
+
+ buffer_info->dma = 0;
+ if (buffer_info->skb) {
+ skb_dma_unmap(&adapter->pdev->dev, buffer_info->skb,
+ DMA_TO_DEVICE);
+ dev_kfree_skb_any(buffer_info->skb);
+ buffer_info->skb = NULL;
+ }
+ buffer_info->time_stamp = 0;
+ /* buffer_info must be completely set up in the transmit path */
+}
+
+/**
+ * e1000_clean_tx_ring - Free Tx Buffers
+ * @adapter: board private structure
+ * @tx_ring: ring to be cleaned
+ **/
+
+static void e1000_clean_tx_ring(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_buffer *buffer_info;
+ unsigned long size;
+ unsigned int i;
+
+ /* Free all the Tx ring sk_buffs */
+
+ for (i = 0; i < tx_ring->count; i++) {
+ buffer_info = &tx_ring->buffer_info[i];
+ e1000_unmap_and_free_tx_resource(adapter, buffer_info);
+ }
+
+ size = sizeof(struct e1000_buffer) * tx_ring->count;
+ memset(tx_ring->buffer_info, 0, size);
+
+ /* Zero out the descriptor ring */
+
+ memset(tx_ring->desc, 0, tx_ring->size);
+
+ tx_ring->next_to_use = 0;
+ tx_ring->next_to_clean = 0;
+ tx_ring->last_tx_tso = 0;
+
+ writel(0, hw->hw_addr + tx_ring->tdh);
+ writel(0, hw->hw_addr + tx_ring->tdt);
+}
+
+/**
+ * e1000_clean_all_tx_rings - Free Tx Buffers for all queues
+ * @adapter: board private structure
+ **/
+
+static void e1000_clean_all_tx_rings(struct e1000_adapter *adapter)
+{
+ int i;
+
+ for (i = 0; i < adapter->num_tx_queues; i++)
+ e1000_clean_tx_ring(adapter, &adapter->tx_ring[i]);
+}
+
+/**
+ * e1000_free_rx_resources - Free Rx Resources
+ * @adapter: board private structure
+ * @rx_ring: ring to clean the resources from
+ *
+ * Free all receive software resources
+ **/
+
+static void e1000_free_rx_resources(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring)
+{
+ struct pci_dev *pdev = adapter->pdev;
+
+ e1000_clean_rx_ring(adapter, rx_ring);
+
+ vfree(rx_ring->buffer_info);
+ rx_ring->buffer_info = NULL;
+
+ pci_free_consistent(pdev, rx_ring->size, rx_ring->desc, rx_ring->dma);
+
+ rx_ring->desc = NULL;
+}
+
+/**
+ * e1000_free_all_rx_resources - Free Rx Resources for All Queues
+ * @adapter: board private structure
+ *
+ * Free all receive software resources
+ **/
+
+void e1000_free_all_rx_resources(struct e1000_adapter *adapter)
+{
+ int i;
+
+ for (i = 0; i < adapter->num_rx_queues; i++)
+ e1000_free_rx_resources(adapter, &adapter->rx_ring[i]);
+}
+
+/**
+ * e1000_clean_rx_ring - Free Rx Buffers per Queue
+ * @adapter: board private structure
+ * @rx_ring: ring to free buffers from
+ **/
+
+static void e1000_clean_rx_ring(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_buffer *buffer_info;
+ struct pci_dev *pdev = adapter->pdev;
+ unsigned long size;
+ unsigned int i;
+
+ /* Free all the Rx ring sk_buffs */
+ for (i = 0; i < rx_ring->count; i++) {
+ buffer_info = &rx_ring->buffer_info[i];
+ if (buffer_info->dma &&
+ adapter->clean_rx == e1000_clean_rx_irq) {
+ pci_unmap_single(pdev, buffer_info->dma,
+ buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+ } else if (buffer_info->dma &&
+ adapter->clean_rx == e1000_clean_jumbo_rx_irq) {
+ pci_unmap_page(pdev, buffer_info->dma,
+ buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+ }
+
+ buffer_info->dma = 0;
+ if (buffer_info->page) {
+ put_page(buffer_info->page);
+ buffer_info->page = NULL;
+ }
+ if (buffer_info->skb) {
+ dev_kfree_skb(buffer_info->skb);
+ buffer_info->skb = NULL;
+ }
+ }
+
+ /* there also may be some cached data from a chained receive */
+ if (rx_ring->rx_skb_top) {
+ dev_kfree_skb(rx_ring->rx_skb_top);
+ rx_ring->rx_skb_top = NULL;
+ }
+
+ size = sizeof(struct e1000_buffer) * rx_ring->count;
+ memset(rx_ring->buffer_info, 0, size);
+
+ /* Zero out the descriptor ring */
+ memset(rx_ring->desc, 0, rx_ring->size);
+
+ rx_ring->next_to_clean = 0;
+ rx_ring->next_to_use = 0;
+
+ writel(0, hw->hw_addr + rx_ring->rdh);
+ writel(0, hw->hw_addr + rx_ring->rdt);
+}
+
+/**
+ * e1000_clean_all_rx_rings - Free Rx Buffers for all queues
+ * @adapter: board private structure
+ **/
+
+static void e1000_clean_all_rx_rings(struct e1000_adapter *adapter)
+{
+ int i;
+
+ for (i = 0; i < adapter->num_rx_queues; i++)
+ e1000_clean_rx_ring(adapter, &adapter->rx_ring[i]);
+}
+
+/* The 82542 2.0 (revision 2) needs to have the receive unit in reset
+ * and memory write and invalidate disabled for certain operations
+ */
+static void e1000_enter_82542_rst(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u32 rctl;
+
+ e1000_pci_clear_mwi(hw);
+
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_RST;
+ ew32(RCTL, rctl);
+ E1000_WRITE_FLUSH();
+ mdelay(5);
+
+ if (!adapter->ecdev && netif_running(netdev))
+ e1000_clean_all_rx_rings(adapter);
+}
+
+static void e1000_leave_82542_rst(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u32 rctl;
+
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_RST;
+ ew32(RCTL, rctl);
+ E1000_WRITE_FLUSH();
+ mdelay(5);
+
+ if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE)
+ e1000_pci_set_mwi(hw);
+
+ if (!adapter->netdev && netif_running(netdev)) {
+ /* No need to loop, because 82542 supports only 1 queue */
+ struct e1000_rx_ring *ring = &adapter->rx_ring[0];
+ e1000_configure_rx(adapter);
+ if (adapter->ecdev) {
+ /* fill rx ring completely! */
+ adapter->alloc_rx_buf(adapter, ring, ring->count);
+ } else {
+ /* this one leaves the last ring element unallocated! */
+ adapter->alloc_rx_buf(adapter, ring, E1000_DESC_UNUSED(ring));
+ }
+
+ }
+}
+
+/**
+ * e1000_set_mac - Change the Ethernet Address of the NIC
+ * @netdev: network interface device structure
+ * @p: pointer to an address structure
+ *
+ * Returns 0 on success, negative on failure
+ **/
+
+static int e1000_set_mac(struct net_device *netdev, void *p)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct sockaddr *addr = p;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ /* 82542 2.0 needs to be in reset to write receive address registers */
+
+ if (hw->mac_type == e1000_82542_rev2_0)
+ e1000_enter_82542_rst(adapter);
+
+ memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
+ memcpy(hw->mac_addr, addr->sa_data, netdev->addr_len);
+
+ e1000_rar_set(hw, hw->mac_addr, 0);
+
+ if (hw->mac_type == e1000_82542_rev2_0)
+ e1000_leave_82542_rst(adapter);
+
+ return 0;
+}
+
+/**
+ * e1000_set_rx_mode - Secondary Unicast, Multicast and Promiscuous mode set
+ * @netdev: network interface device structure
+ *
+ * The set_rx_mode entry point is called whenever the unicast or multicast
+ * address lists or the network interface flags are updated. This routine is
+ * responsible for configuring the hardware for proper unicast, multicast,
+ * promiscuous mode, and all-multi behavior.
+ **/
+
+static void e1000_set_rx_mode(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct netdev_hw_addr *ha;
+ bool use_uc = false;
+ struct dev_addr_list *mc_ptr;
+ u32 rctl;
+ u32 hash_value;
+ int i, rar_entries = E1000_RAR_ENTRIES;
+ int mta_reg_count = E1000_NUM_MTA_REGISTERS;
+ u32 *mcarray = kcalloc(mta_reg_count, sizeof(u32), GFP_ATOMIC);
+
+ if (!mcarray) {
+ DPRINTK(PROBE, ERR, "memory allocation failed\n");
+ return;
+ }
+
+ /* Check for Promiscuous and All Multicast modes */
+
+ rctl = er32(RCTL);
+
+ if (netdev->flags & IFF_PROMISC) {
+ rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE);
+ rctl &= ~E1000_RCTL_VFE;
+ } else {
+ if (netdev->flags & IFF_ALLMULTI)
+ rctl |= E1000_RCTL_MPE;
+ else
+ rctl &= ~E1000_RCTL_MPE;
+ /* Enable VLAN filter if there is a VLAN */
+ if (adapter->vlgrp)
+ rctl |= E1000_RCTL_VFE;
+ }
+
+ if (netdev->uc.count > rar_entries - 1) {
+ rctl |= E1000_RCTL_UPE;
+ } else if (!(netdev->flags & IFF_PROMISC)) {
+ rctl &= ~E1000_RCTL_UPE;
+ use_uc = true;
+ }
+
+ ew32(RCTL, rctl);
+
+ /* 82542 2.0 needs to be in reset to write receive address registers */
+
+ if (hw->mac_type == e1000_82542_rev2_0)
+ e1000_enter_82542_rst(adapter);
+
+ /* load the first 14 addresses into the exact filters 1-14. Unicast
+ * addresses take precedence to avoid disabling unicast filtering
+ * when possible.
+ *
+ * RAR 0 is used for the station MAC adddress
+ * if there are not 14 addresses, go ahead and clear the filters
+ */
+ i = 1;
+ if (use_uc)
+ list_for_each_entry(ha, &netdev->uc.list, list) {
+ if (i == rar_entries)
+ break;
+ e1000_rar_set(hw, ha->addr, i++);
+ }
+
+ WARN_ON(i == rar_entries);
+
+ mc_ptr = netdev->mc_list;
+
+ for (; i < rar_entries; i++) {
+ if (mc_ptr) {
+ e1000_rar_set(hw, mc_ptr->da_addr, i);
+ mc_ptr = mc_ptr->next;
+ } else {
+ E1000_WRITE_REG_ARRAY(hw, RA, i << 1, 0);
+ E1000_WRITE_FLUSH();
+ E1000_WRITE_REG_ARRAY(hw, RA, (i << 1) + 1, 0);
+ E1000_WRITE_FLUSH();
+ }
+ }
+
+ /* load any remaining addresses into the hash table */
+
+ for (; mc_ptr; mc_ptr = mc_ptr->next) {
+ u32 hash_reg, hash_bit, mta;
+ hash_value = e1000_hash_mc_addr(hw, mc_ptr->da_addr);
+ hash_reg = (hash_value >> 5) & 0x7F;
+ hash_bit = hash_value & 0x1F;
+ mta = (1 << hash_bit);
+ mcarray[hash_reg] |= mta;
+ }
+
+ /* write the hash table completely, write from bottom to avoid
+ * both stupid write combining chipsets, and flushing each write */
+ for (i = mta_reg_count - 1; i >= 0 ; i--) {
+ /*
+ * If we are on an 82544 has an errata where writing odd
+ * offsets overwrites the previous even offset, but writing
+ * backwards over the range solves the issue by always
+ * writing the odd offset first
+ */
+ E1000_WRITE_REG_ARRAY(hw, MTA, i, mcarray[i]);
+ }
+ E1000_WRITE_FLUSH();
+
+ if (hw->mac_type == e1000_82542_rev2_0)
+ e1000_leave_82542_rst(adapter);
+
+ kfree(mcarray);
+}
+
+/* Need to wait a few seconds after link up to get diagnostic information from
+ * the phy */
+
+static void e1000_update_phy_info(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *)data;
+ struct e1000_hw *hw = &adapter->hw;
+ e1000_phy_get_info(hw, &adapter->phy_info);
+}
+
+/**
+ * e1000_82547_tx_fifo_stall - Timer Call-back
+ * @data: pointer to adapter cast into an unsigned long
+ **/
+
+static void e1000_82547_tx_fifo_stall(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *)data;
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u32 tctl;
+
+ if (atomic_read(&adapter->tx_fifo_stall)) {
+ if ((er32(TDT) == er32(TDH)) &&
+ (er32(TDFT) == er32(TDFH)) &&
+ (er32(TDFTS) == er32(TDFHS))) {
+ tctl = er32(TCTL);
+ ew32(TCTL, tctl & ~E1000_TCTL_EN);
+ ew32(TDFT, adapter->tx_head_addr);
+ ew32(TDFH, adapter->tx_head_addr);
+ ew32(TDFTS, adapter->tx_head_addr);
+ ew32(TDFHS, adapter->tx_head_addr);
+ ew32(TCTL, tctl);
+ E1000_WRITE_FLUSH();
+
+ adapter->tx_fifo_head = 0;
+ atomic_set(&adapter->tx_fifo_stall, 0);
+ if (!adapter->ecdev) netif_wake_queue(netdev);
+ } else if (!test_bit(__E1000_DOWN, &adapter->flags)) {
+ if (!adapter->ecdev)
+ mod_timer(&adapter->tx_fifo_stall_timer, jiffies + 1);
+ }
+ }
+}
+
+static bool e1000_has_link(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ bool link_active = false;
+
+ /* get_link_status is set on LSC (link status) interrupt or
+ * rx sequence error interrupt. get_link_status will stay
+ * false until the e1000_check_for_link establishes link
+ * for copper adapters ONLY
+ */
+ switch (hw->media_type) {
+ case e1000_media_type_copper:
+ if (hw->get_link_status) {
+ e1000_check_for_link(hw);
+ link_active = !hw->get_link_status;
+ } else {
+ link_active = true;
+ }
+ break;
+ case e1000_media_type_fiber:
+ e1000_check_for_link(hw);
+ link_active = !!(er32(STATUS) & E1000_STATUS_LU);
+ break;
+ case e1000_media_type_internal_serdes:
+ e1000_check_for_link(hw);
+ link_active = hw->serdes_has_link;
+ break;
+ default:
+ break;
+ }
+
+ return link_active;
+}
+
+/**
+ * e1000_watchdog - Timer Call-back
+ * @data: pointer to adapter cast into an unsigned long
+ **/
+static void e1000_watchdog(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *)data;
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_tx_ring *txdr = adapter->tx_ring;
+ u32 link, tctl;
+
+ link = e1000_has_link(adapter);
+ if (!adapter->ecdev && (netif_carrier_ok(netdev)) && link)
+ goto link_up;
+
+ if (link) {
+ if ((adapter->ecdev && !ecdev_get_link(adapter->ecdev))
+ || (!adapter->ecdev && !netif_carrier_ok(netdev))) {
+ u32 ctrl;
+ bool txb2b = true;
+ /* update snapshot of PHY registers on LSC */
+ e1000_get_speed_and_duplex(hw,
+ &adapter->link_speed,
+ &adapter->link_duplex);
+
+ ctrl = er32(CTRL);
+ printk(KERN_INFO "e1000: %s NIC Link is Up %d Mbps %s, "
+ "Flow Control: %s\n",
+ netdev->name,
+ adapter->link_speed,
+ adapter->link_duplex == FULL_DUPLEX ?
+ "Full Duplex" : "Half Duplex",
+ ((ctrl & E1000_CTRL_TFCE) && (ctrl &
+ E1000_CTRL_RFCE)) ? "RX/TX" : ((ctrl &
+ E1000_CTRL_RFCE) ? "RX" : ((ctrl &
+ E1000_CTRL_TFCE) ? "TX" : "None" )));
+
+ /* tweak tx_queue_len according to speed/duplex
+ * and adjust the timeout factor */
+ netdev->tx_queue_len = adapter->tx_queue_len;
+ adapter->tx_timeout_factor = 1;
+ switch (adapter->link_speed) {
+ case SPEED_10:
+ txb2b = false;
+ netdev->tx_queue_len = 10;
+ adapter->tx_timeout_factor = 16;
+ break;
+ case SPEED_100:
+ txb2b = false;
+ netdev->tx_queue_len = 100;
+ /* maybe add some timeout factor ? */
+ break;
+ }
+
+ /* enable transmits in the hardware */
+ tctl = er32(TCTL);
+ tctl |= E1000_TCTL_EN;
+ ew32(TCTL, tctl);
+
+ if (adapter->ecdev) {
+ ecdev_set_link(adapter->ecdev, 1);
+ } else {
+ netif_carrier_on(netdev);
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->phy_info_timer,
+ round_jiffies(jiffies + 2 * HZ));
+ }
+ adapter->smartspeed = 0;
+ }
+ } else {
+ if ((adapter->ecdev && ecdev_get_link(adapter->ecdev))
+ || (!adapter->ecdev && netif_carrier_ok(netdev))) {
+ adapter->link_speed = 0;
+ adapter->link_duplex = 0;
+ printk(KERN_INFO "e1000: %s NIC Link is Down\n",
+ netdev->name);
+ if (adapter->ecdev) {
+ ecdev_set_link(adapter->ecdev, 0);
+ } else {
+ netif_carrier_off(netdev);
+
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->phy_info_timer,
+ round_jiffies(jiffies + 2 * HZ));
+ }
+ }
+
+ e1000_smartspeed(adapter);
+ }
+
+link_up:
+ e1000_update_stats(adapter);
+
+ hw->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old;
+ adapter->tpt_old = adapter->stats.tpt;
+ hw->collision_delta = adapter->stats.colc - adapter->colc_old;
+ adapter->colc_old = adapter->stats.colc;
+
+ adapter->gorcl = adapter->stats.gorcl - adapter->gorcl_old;
+ adapter->gorcl_old = adapter->stats.gorcl;
+ adapter->gotcl = adapter->stats.gotcl - adapter->gotcl_old;
+ adapter->gotcl_old = adapter->stats.gotcl;
+
+ e1000_update_adaptive(hw);
+
+ if (!adapter->ecdev && !netif_carrier_ok(netdev)) {
+ if (E1000_DESC_UNUSED(txdr) + 1 < txdr->count) {
+ /* We've lost link, so the controller stops DMA,
+ * but we've got queued Tx work that's never going
+ * to get done, so reset controller to flush Tx.
+ * (Do the reset outside of interrupt context). */
+ adapter->tx_timeout_count++;
+ schedule_work(&adapter->reset_task);
+ /* return immediately since reset is imminent */
+ return;
+ }
+ }
+
+ /* Cause software interrupt to ensure rx ring is cleaned */
+ ew32(ICS, E1000_ICS_RXDMT0);
+
+ /* Force detection of hung controller every watchdog period */
+ if (!adapter->ecdev) adapter->detect_tx_hung = true;
+
+ /* Reset the timer */
+ if (!adapter->ecdev) {
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->watchdog_timer,
+ round_jiffies(jiffies + 2 * HZ));
+ }
+}
+
+enum latency_range {
+ lowest_latency = 0,
+ low_latency = 1,
+ bulk_latency = 2,
+ latency_invalid = 255
+};
+
+/**
+ * e1000_update_itr - update the dynamic ITR value based on statistics
+ * @adapter: pointer to adapter
+ * @itr_setting: current adapter->itr
+ * @packets: the number of packets during this measurement interval
+ * @bytes: the number of bytes during this measurement interval
+ *
+ * Stores a new ITR value based on packets and byte
+ * counts during the last interrupt. The advantage of per interrupt
+ * computation is faster updates and more accurate ITR for the current
+ * traffic pattern. Constants in this function were computed
+ * based on theoretical maximum wire speed and thresholds were set based
+ * on testing data as well as attempting to minimize response time
+ * while increasing bulk throughput.
+ * this functionality is controlled by the InterruptThrottleRate module
+ * parameter (see e1000_param.c)
+ **/
+static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
+ u16 itr_setting, int packets, int bytes)
+{
+ unsigned int retval = itr_setting;
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (unlikely(hw->mac_type < e1000_82540))
+ goto update_itr_done;
+
+ if (packets == 0)
+ goto update_itr_done;
+
+ switch (itr_setting) {
+ case lowest_latency:
+ /* jumbo frames get bulk treatment*/
+ if (bytes/packets > 8000)
+ retval = bulk_latency;
+ else if ((packets < 5) && (bytes > 512))
+ retval = low_latency;
+ break;
+ case low_latency: /* 50 usec aka 20000 ints/s */
+ if (bytes > 10000) {
+ /* jumbo frames need bulk latency setting */
+ if (bytes/packets > 8000)
+ retval = bulk_latency;
+ else if ((packets < 10) || ((bytes/packets) > 1200))
+ retval = bulk_latency;
+ else if ((packets > 35))
+ retval = lowest_latency;
+ } else if (bytes/packets > 2000)
+ retval = bulk_latency;
+ else if (packets <= 2 && bytes < 512)
+ retval = lowest_latency;
+ break;
+ case bulk_latency: /* 250 usec aka 4000 ints/s */
+ if (bytes > 25000) {
+ if (packets > 35)
+ retval = low_latency;
+ } else if (bytes < 6000) {
+ retval = low_latency;
+ }
+ break;
+ }
+
+update_itr_done:
+ return retval;
+}
+
+static void e1000_set_itr(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 current_itr;
+ u32 new_itr = adapter->itr;
+
+ if (unlikely(hw->mac_type < e1000_82540))
+ return;
+
+ /* for non-gigabit speeds, just fix the interrupt rate at 4000 */
+ if (unlikely(adapter->link_speed != SPEED_1000)) {
+ current_itr = 0;
+ new_itr = 4000;
+ goto set_itr_now;
+ }
+
+ adapter->tx_itr = e1000_update_itr(adapter,
+ adapter->tx_itr,
+ adapter->total_tx_packets,
+ adapter->total_tx_bytes);
+ /* conservative mode (itr 3) eliminates the lowest_latency setting */
+ if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency)
+ adapter->tx_itr = low_latency;
+
+ adapter->rx_itr = e1000_update_itr(adapter,
+ adapter->rx_itr,
+ adapter->total_rx_packets,
+ adapter->total_rx_bytes);
+ /* conservative mode (itr 3) eliminates the lowest_latency setting */
+ if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency)
+ adapter->rx_itr = low_latency;
+
+ current_itr = max(adapter->rx_itr, adapter->tx_itr);
+
+ switch (current_itr) {
+ /* counts and packets in update_itr are dependent on these numbers */
+ case lowest_latency:
+ new_itr = 70000;
+ break;
+ case low_latency:
+ new_itr = 20000; /* aka hwitr = ~200 */
+ break;
+ case bulk_latency:
+ new_itr = 4000;
+ break;
+ default:
+ break;
+ }
+
+set_itr_now:
+ if (new_itr != adapter->itr) {
+ /* this attempts to bias the interrupt rate towards Bulk
+ * by adding intermediate steps when interrupt rate is
+ * increasing */
+ new_itr = new_itr > adapter->itr ?
+ min(adapter->itr + (new_itr >> 2), new_itr) :
+ new_itr;
+ adapter->itr = new_itr;
+ ew32(ITR, 1000000000 / (new_itr * 256));
+ }
+
+ return;
+}
+
+#define E1000_TX_FLAGS_CSUM 0x00000001
+#define E1000_TX_FLAGS_VLAN 0x00000002
+#define E1000_TX_FLAGS_TSO 0x00000004
+#define E1000_TX_FLAGS_IPV4 0x00000008
+#define E1000_TX_FLAGS_VLAN_MASK 0xffff0000
+#define E1000_TX_FLAGS_VLAN_SHIFT 16
+
+static int e1000_tso(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring, struct sk_buff *skb)
+{
+ struct e1000_context_desc *context_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i;
+ u32 cmd_length = 0;
+ u16 ipcse = 0, tucse, mss;
+ u8 ipcss, ipcso, tucss, tucso, hdr_len;
+ int err;
+
+ if (skb_is_gso(skb)) {
+ if (skb_header_cloned(skb)) {
+ err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
+ if (err)
+ return err;
+ }
+
+ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ mss = skb_shinfo(skb)->gso_size;
+ if (skb->protocol == htons(ETH_P_IP)) {
+ struct iphdr *iph = ip_hdr(skb);
+ iph->tot_len = 0;
+ iph->check = 0;
+ tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr,
+ iph->daddr, 0,
+ IPPROTO_TCP,
+ 0);
+ cmd_length = E1000_TXD_CMD_IP;
+ ipcse = skb_transport_offset(skb) - 1;
+ } else if (skb->protocol == htons(ETH_P_IPV6)) {
+ ipv6_hdr(skb)->payload_len = 0;
+ tcp_hdr(skb)->check =
+ ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
+ &ipv6_hdr(skb)->daddr,
+ 0, IPPROTO_TCP, 0);
+ ipcse = 0;
+ }
+ ipcss = skb_network_offset(skb);
+ ipcso = (void *)&(ip_hdr(skb)->check) - (void *)skb->data;
+ tucss = skb_transport_offset(skb);
+ tucso = (void *)&(tcp_hdr(skb)->check) - (void *)skb->data;
+ tucse = 0;
+
+ cmd_length |= (E1000_TXD_CMD_DEXT | E1000_TXD_CMD_TSE |
+ E1000_TXD_CMD_TCP | (skb->len - (hdr_len)));
+
+ i = tx_ring->next_to_use;
+ context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
+ buffer_info = &tx_ring->buffer_info[i];
+
+ context_desc->lower_setup.ip_fields.ipcss = ipcss;
+ context_desc->lower_setup.ip_fields.ipcso = ipcso;
+ context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse);
+ context_desc->upper_setup.tcp_fields.tucss = tucss;
+ context_desc->upper_setup.tcp_fields.tucso = tucso;
+ context_desc->upper_setup.tcp_fields.tucse = cpu_to_le16(tucse);
+ context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss);
+ context_desc->tcp_seg_setup.fields.hdr_len = hdr_len;
+ context_desc->cmd_and_length = cpu_to_le32(cmd_length);
+
+ buffer_info->time_stamp = jiffies;
+ buffer_info->next_to_watch = i;
+
+ if (++i == tx_ring->count) i = 0;
+ tx_ring->next_to_use = i;
+
+ return true;
+ }
+ return false;
+}
+
+static bool e1000_tx_csum(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring, struct sk_buff *skb)
+{
+ struct e1000_context_desc *context_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i;
+ u8 css;
+ u32 cmd_len = E1000_TXD_CMD_DEXT;
+
+ if (skb->ip_summed != CHECKSUM_PARTIAL)
+ return false;
+
+ switch (skb->protocol) {
+ case cpu_to_be16(ETH_P_IP):
+ if (ip_hdr(skb)->protocol == IPPROTO_TCP)
+ cmd_len |= E1000_TXD_CMD_TCP;
+ break;
+ case cpu_to_be16(ETH_P_IPV6):
+ /* XXX not handling all IPV6 headers */
+ if (ipv6_hdr(skb)->nexthdr == IPPROTO_TCP)
+ cmd_len |= E1000_TXD_CMD_TCP;
+ break;
+ default:
+ if (unlikely(net_ratelimit()))
+ DPRINTK(DRV, WARNING,
+ "checksum_partial proto=%x!\n", skb->protocol);
+ break;
+ }
+
+ css = skb_transport_offset(skb);
+
+ i = tx_ring->next_to_use;
+ buffer_info = &tx_ring->buffer_info[i];
+ context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
+
+ context_desc->lower_setup.ip_config = 0;
+ context_desc->upper_setup.tcp_fields.tucss = css;
+ context_desc->upper_setup.tcp_fields.tucso =
+ css + skb->csum_offset;
+ context_desc->upper_setup.tcp_fields.tucse = 0;
+ context_desc->tcp_seg_setup.data = 0;
+ context_desc->cmd_and_length = cpu_to_le32(cmd_len);
+
+ buffer_info->time_stamp = jiffies;
+ buffer_info->next_to_watch = i;
+
+ if (unlikely(++i == tx_ring->count)) i = 0;
+ tx_ring->next_to_use = i;
+
+ return true;
+}
+
+#define E1000_MAX_TXD_PWR 12
+#define E1000_MAX_DATA_PER_TXD (1<<E1000_MAX_TXD_PWR)
+
+static int e1000_tx_map(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring,
+ struct sk_buff *skb, unsigned int first,
+ unsigned int max_per_txd, unsigned int nr_frags,
+ unsigned int mss)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_buffer *buffer_info;
+ unsigned int len = skb_headlen(skb);
+ unsigned int offset, size, count = 0, i;
+ unsigned int f;
+ dma_addr_t *map;
+
+ i = tx_ring->next_to_use;
+
+ if (skb_dma_map(&adapter->pdev->dev, skb, DMA_TO_DEVICE)) {
+ dev_err(&adapter->pdev->dev, "TX DMA map failed\n");
+ return 0;
+ }
+
+ map = skb_shinfo(skb)->dma_maps;
+ offset = 0;
+
+ while (len) {
+ buffer_info = &tx_ring->buffer_info[i];
+ size = min(len, max_per_txd);
+ /* Workaround for Controller erratum --
+ * descriptor for non-tso packet in a linear SKB that follows a
+ * tso gets written back prematurely before the data is fully
+ * DMA'd to the controller */
+ if (!skb->data_len && tx_ring->last_tx_tso &&
+ !skb_is_gso(skb)) {
+ tx_ring->last_tx_tso = 0;
+ size -= 4;
+ }
+
+ /* Workaround for premature desc write-backs
+ * in TSO mode. Append 4-byte sentinel desc */
+ if (unlikely(mss && !nr_frags && size == len && size > 8))
+ size -= 4;
+ /* work-around for errata 10 and it applies
+ * to all controllers in PCI-X mode
+ * The fix is to make sure that the first descriptor of a
+ * packet is smaller than 2048 - 16 - 16 (or 2016) bytes
+ */
+ if (unlikely((hw->bus_type == e1000_bus_type_pcix) &&
+ (size > 2015) && count == 0))
+ size = 2015;
+
+ /* Workaround for potential 82544 hang in PCI-X. Avoid
+ * terminating buffers within evenly-aligned dwords. */
+ if (unlikely(adapter->pcix_82544 &&
+ !((unsigned long)(skb->data + offset + size - 1) & 4) &&
+ size > 4))
+ size -= 4;
+
+ buffer_info->length = size;
+ /* set time_stamp *before* dma to help avoid a possible race */
+ buffer_info->time_stamp = jiffies;
+ buffer_info->dma = skb_shinfo(skb)->dma_head + offset;
+ buffer_info->next_to_watch = i;
+
+ len -= size;
+ offset += size;
+ count++;
+ if (len) {
+ i++;
+ if (unlikely(i == tx_ring->count))
+ i = 0;
+ }
+ }
+
+ for (f = 0; f < nr_frags; f++) {
+ struct skb_frag_struct *frag;
+
+ frag = &skb_shinfo(skb)->frags[f];
+ len = frag->size;
+ offset = 0;
+
+ while (len) {
+ i++;
+ if (unlikely(i == tx_ring->count))
+ i = 0;
+
+ buffer_info = &tx_ring->buffer_info[i];
+ size = min(len, max_per_txd);
+ /* Workaround for premature desc write-backs
+ * in TSO mode. Append 4-byte sentinel desc */
+ if (unlikely(mss && f == (nr_frags-1) && size == len && size > 8))
+ size -= 4;
+ /* Workaround for potential 82544 hang in PCI-X.
+ * Avoid terminating buffers within evenly-aligned
+ * dwords. */
+ if (unlikely(adapter->pcix_82544 &&
+ !((unsigned long)(page_to_phys(frag->page) + offset
+ + size - 1) & 4) &&
+ size > 4))
+ size -= 4;
+
+ buffer_info->length = size;
+ buffer_info->time_stamp = jiffies;
+ buffer_info->dma = map[f] + offset;
+ buffer_info->next_to_watch = i;
+
+ len -= size;
+ offset += size;
+ count++;
+ }
+ }
+
+ tx_ring->buffer_info[i].skb = skb;
+ tx_ring->buffer_info[first].next_to_watch = i;
+
+ return count;
+}
+
+static void e1000_tx_queue(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring, int tx_flags,
+ int count)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_tx_desc *tx_desc = NULL;
+ struct e1000_buffer *buffer_info;
+ u32 txd_upper = 0, txd_lower = E1000_TXD_CMD_IFCS;
+ unsigned int i;
+
+ if (likely(tx_flags & E1000_TX_FLAGS_TSO)) {
+ txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D |
+ E1000_TXD_CMD_TSE;
+ txd_upper |= E1000_TXD_POPTS_TXSM << 8;
+
+ if (likely(tx_flags & E1000_TX_FLAGS_IPV4))
+ txd_upper |= E1000_TXD_POPTS_IXSM << 8;
+ }
+
+ if (likely(tx_flags & E1000_TX_FLAGS_CSUM)) {
+ txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
+ txd_upper |= E1000_TXD_POPTS_TXSM << 8;
+ }
+
+ if (unlikely(tx_flags & E1000_TX_FLAGS_VLAN)) {
+ txd_lower |= E1000_TXD_CMD_VLE;
+ txd_upper |= (tx_flags & E1000_TX_FLAGS_VLAN_MASK);
+ }
+
+ i = tx_ring->next_to_use;
+
+ while (count--) {
+ buffer_info = &tx_ring->buffer_info[i];
+ tx_desc = E1000_TX_DESC(*tx_ring, i);
+ tx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+ tx_desc->lower.data =
+ cpu_to_le32(txd_lower | buffer_info->length);
+ tx_desc->upper.data = cpu_to_le32(txd_upper);
+ if (unlikely(++i == tx_ring->count)) i = 0;
+ }
+
+ tx_desc->lower.data |= cpu_to_le32(adapter->txd_cmd);
+
+ /* Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64). */
+ wmb();
+
+ tx_ring->next_to_use = i;
+ writel(i, hw->hw_addr + tx_ring->tdt);
+ /* we need this if more than one processor can write to our tail
+ * at a time, it syncronizes IO on IA64/Altix systems */
+ mmiowb();
+}
+
+/**
+ * 82547 workaround to avoid controller hang in half-duplex environment.
+ * The workaround is to avoid queuing a large packet that would span
+ * the internal Tx FIFO ring boundary by notifying the stack to resend
+ * the packet at a later time. This gives the Tx FIFO an opportunity to
+ * flush all packets. When that occurs, we reset the Tx FIFO pointers
+ * to the beginning of the Tx FIFO.
+ **/
+
+#define E1000_FIFO_HDR 0x10
+#define E1000_82547_PAD_LEN 0x3E0
+
+static int e1000_82547_fifo_workaround(struct e1000_adapter *adapter,
+ struct sk_buff *skb)
+{
+ u32 fifo_space = adapter->tx_fifo_size - adapter->tx_fifo_head;
+ u32 skb_fifo_len = skb->len + E1000_FIFO_HDR;
+
+ skb_fifo_len = ALIGN(skb_fifo_len, E1000_FIFO_HDR);
+
+ if (adapter->link_duplex != HALF_DUPLEX)
+ goto no_fifo_stall_required;
+
+ if (atomic_read(&adapter->tx_fifo_stall))
+ return 1;
+
+ if (skb_fifo_len >= (E1000_82547_PAD_LEN + fifo_space)) {
+ atomic_set(&adapter->tx_fifo_stall, 1);
+ return 1;
+ }
+
+no_fifo_stall_required:
+ adapter->tx_fifo_head += skb_fifo_len;
+ if (adapter->tx_fifo_head >= adapter->tx_fifo_size)
+ adapter->tx_fifo_head -= adapter->tx_fifo_size;
+ return 0;
+}
+
+static int __e1000_maybe_stop_tx(struct net_device *netdev, int size)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_tx_ring *tx_ring = adapter->tx_ring;
+
+ netif_stop_queue(netdev);
+ /* Herbert's original patch had:
+ * smp_mb__after_netif_stop_queue();
+ * but since that doesn't exist yet, just open code it. */
+ smp_mb();
+
+ /* We need to check again in a case another CPU has just
+ * made room available. */
+ if (likely(E1000_DESC_UNUSED(tx_ring) < size))
+ return -EBUSY;
+
+ /* A reprieve! */
+ netif_start_queue(netdev);
+ ++adapter->restart_queue;
+ return 0;
+}
+
+static int e1000_maybe_stop_tx(struct net_device *netdev,
+ struct e1000_tx_ring *tx_ring, int size)
+{
+ if (likely(E1000_DESC_UNUSED(tx_ring) >= size))
+ return 0;
+ return __e1000_maybe_stop_tx(netdev, size);
+}
+
+#define TXD_USE_COUNT(S, X) (((S) >> (X)) + 1 )
+static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
+ struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_tx_ring *tx_ring;
+ unsigned int first, max_per_txd = E1000_MAX_DATA_PER_TXD;
+ unsigned int max_txd_pwr = E1000_MAX_TXD_PWR;
+ unsigned int tx_flags = 0;
+ unsigned int len = skb->len - skb->data_len;
+ unsigned int nr_frags = 0;
+ unsigned int mss = 0;
+ int count = 0;
+ int tso;
+ unsigned int f;
+
+ /* This goes back to the question of how to logically map a tx queue
+ * to a flow. Right now, performance is impacted slightly negatively
+ * if using multiple tx queues. If the stack breaks away from a
+ * single qdisc implementation, we can look at this again. */
+ tx_ring = adapter->tx_ring;
+
+ if (unlikely(skb->len <= 0)) {
+ if (!adapter->ecdev)
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
+ mss = skb_shinfo(skb)->gso_size;
+ /* The controller does a simple calculation to
+ * make sure there is enough room in the FIFO before
+ * initiating the DMA for each buffer. The calc is:
+ * 4 = ceil(buffer len/mss). To make sure we don't
+ * overrun the FIFO, adjust the max buffer len if mss
+ * drops. */
+ if (mss) {
+ u8 hdr_len;
+ max_per_txd = min(mss << 2, max_per_txd);
+ max_txd_pwr = fls(max_per_txd) - 1;
+
+ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ if (skb->data_len && hdr_len == len) {
+ switch (hw->mac_type) {
+ unsigned int pull_size;
+ case e1000_82544:
+ /* Make sure we have room to chop off 4 bytes,
+ * and that the end alignment will work out to
+ * this hardware's requirements
+ * NOTE: this is a TSO only workaround
+ * if end byte alignment not correct move us
+ * into the next dword */
+ if ((unsigned long)(skb_tail_pointer(skb) - 1) & 4)
+ break;
+ /* fall through */
+ pull_size = min((unsigned int)4, skb->data_len);
+ if (!__pskb_pull_tail(skb, pull_size)) {
+ DPRINTK(DRV, ERR,
+ "__pskb_pull_tail failed.\n");
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+ len = skb->len - skb->data_len;
+ break;
+ default:
+ /* do nothing */
+ break;
+ }
+ }
+ }
+
+ /* reserve a descriptor for the offload context */
+ if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
+ count++;
+ count++;
+
+ /* Controller Erratum workaround */
+ if (!skb->data_len && tx_ring->last_tx_tso && !skb_is_gso(skb))
+ count++;
+
+ count += TXD_USE_COUNT(len, max_txd_pwr);
+
+ if (adapter->pcix_82544)
+ count++;
+
+ /* work-around for errata 10 and it applies to all controllers
+ * in PCI-X mode, so add one more descriptor to the count
+ */
+ if (unlikely((hw->bus_type == e1000_bus_type_pcix) &&
+ (len > 2015)))
+ count++;
+
+ nr_frags = skb_shinfo(skb)->nr_frags;
+ for (f = 0; f < nr_frags; f++)
+ count += TXD_USE_COUNT(skb_shinfo(skb)->frags[f].size,
+ max_txd_pwr);
+ if (adapter->pcix_82544)
+ count += nr_frags;
+
+ /* need: count + 2 desc gap to keep tail from touching
+ * head, otherwise try next time */
+ if (unlikely(e1000_maybe_stop_tx(netdev, tx_ring, count + 2)))
+ return NETDEV_TX_BUSY;
+
+ if (unlikely(hw->mac_type == e1000_82547)) {
+ if (unlikely(e1000_82547_fifo_workaround(adapter, skb))) {
+ if (!adapter->ecdev) {
+ netif_stop_queue(netdev);
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->tx_fifo_stall_timer,
+ jiffies + 1);
+ }
+ return NETDEV_TX_BUSY;
+ }
+ }
+
+ if (unlikely(adapter->vlgrp && vlan_tx_tag_present(skb))) {
+ tx_flags |= E1000_TX_FLAGS_VLAN;
+ tx_flags |= (vlan_tx_tag_get(skb) << E1000_TX_FLAGS_VLAN_SHIFT);
+ }
+
+ first = tx_ring->next_to_use;
+
+ tso = e1000_tso(adapter, tx_ring, skb);
+ if (tso < 0) {
+ if (!adapter->ecdev) {
+ dev_kfree_skb_any(skb);
+ }
+ return NETDEV_TX_OK;
+ }
+
+ if (likely(tso)) {
+ if (likely(hw->mac_type != e1000_82544))
+ tx_ring->last_tx_tso = 1;
+ tx_flags |= E1000_TX_FLAGS_TSO;
+ } else if (likely(e1000_tx_csum(adapter, tx_ring, skb)))
+ tx_flags |= E1000_TX_FLAGS_CSUM;
+
+ if (likely(skb->protocol == htons(ETH_P_IP)))
+ tx_flags |= E1000_TX_FLAGS_IPV4;
+
+ count = e1000_tx_map(adapter, tx_ring, skb, first, max_per_txd,
+ nr_frags, mss);
+
+ if (count) {
+ e1000_tx_queue(adapter, tx_ring, tx_flags, count);
+ if (!adapter->ecdev) {
+ /* Make sure there is space in the ring for the next send. */
+ e1000_maybe_stop_tx(netdev, tx_ring, MAX_SKB_FRAGS + 2);
+ }
+
+ } else {
+ if (!adapter->ecdev) dev_kfree_skb_any(skb);
+ tx_ring->buffer_info[first].time_stamp = 0;
+ tx_ring->next_to_use = first;
+ }
+
+ return NETDEV_TX_OK;
+}
+
+/**
+ * e1000_tx_timeout - Respond to a Tx Hang
+ * @netdev: network interface device structure
+ **/
+
+static void e1000_tx_timeout(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ /* Do the reset outside of interrupt context */
+ adapter->tx_timeout_count++;
+ schedule_work(&adapter->reset_task);
+}
+
+static void e1000_reset_task(struct work_struct *work)
+{
+ struct e1000_adapter *adapter =
+ container_of(work, struct e1000_adapter, reset_task);
+
+ e1000_reinit_locked(adapter);
+}
+
+/**
+ * e1000_get_stats - Get System Network Statistics
+ * @netdev: network interface device structure
+ *
+ * Returns the address of the device statistics structure.
+ * The statistics are actually updated from the timer callback.
+ **/
+
+static struct net_device_stats *e1000_get_stats(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ /* only return the current stats */
+ return &adapter->net_stats;
+}
+
+/**
+ * e1000_change_mtu - Change the Maximum Transfer Unit
+ * @netdev: network interface device structure
+ * @new_mtu: new value for maximum frame size
+ *
+ * Returns 0 on success, negative on failure
+ **/
+
+static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ int max_frame = new_mtu + ENET_HEADER_SIZE + ETHERNET_FCS_SIZE;
+
+ if (adapter->ecdev)
+ return -EBUSY;
+
+ if ((max_frame < MINIMUM_ETHERNET_FRAME_SIZE) ||
+ (max_frame > MAX_JUMBO_FRAME_SIZE)) {
+ DPRINTK(PROBE, ERR, "Invalid MTU setting\n");
+ return -EINVAL;
+ }
+
+ /* Adapter-specific max frame size limits. */
+ switch (hw->mac_type) {
+ case e1000_undefined ... e1000_82542_rev2_1:
+ if (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)) {
+ DPRINTK(PROBE, ERR, "Jumbo Frames not supported.\n");
+ return -EINVAL;
+ }
+ break;
+ default:
+ /* Capable of supporting up to MAX_JUMBO_FRAME_SIZE limit. */
+ break;
+ }
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+ /* e1000_down has a dependency on max_frame_size */
+ hw->max_frame_size = max_frame;
+ if (netif_running(netdev))
+ e1000_down(adapter);
+
+ /* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
+ * means we reserve 2 more, this pushes us to allocate from the next
+ * larger slab size.
+ * i.e. RXBUFFER_2048 --> size-4096 slab
+ * however with the new *_jumbo_rx* routines, jumbo receives will use
+ * fragmented skbs */
+
+ if (max_frame <= E1000_RXBUFFER_2048)
+ adapter->rx_buffer_len = E1000_RXBUFFER_2048;
+ else
+#if (PAGE_SIZE >= E1000_RXBUFFER_16384)
+ adapter->rx_buffer_len = E1000_RXBUFFER_16384;
+#elif (PAGE_SIZE >= E1000_RXBUFFER_4096)
+ adapter->rx_buffer_len = PAGE_SIZE;
+#endif
+
+ /* adjust allocation if LPE protects us, and we aren't using SBP */
+ if (!hw->tbi_compatibility_on &&
+ ((max_frame == (ETH_FRAME_LEN + ETH_FCS_LEN)) ||
+ (max_frame == MAXIMUM_ETHERNET_VLAN_SIZE)))
+ adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
+
+ printk(KERN_INFO "e1000: %s changing MTU from %d to %d\n",
+ netdev->name, netdev->mtu, new_mtu);
+ netdev->mtu = new_mtu;
+
+ if (netif_running(netdev))
+ e1000_up(adapter);
+ else
+ e1000_reset(adapter);
+
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+
+ return 0;
+}
+
+/**
+ * e1000_update_stats - Update the board statistics counters
+ * @adapter: board private structure
+ **/
+
+void e1000_update_stats(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct pci_dev *pdev = adapter->pdev;
+ unsigned long flags = 0;
+ u16 phy_tmp;
+
+#define PHY_IDLE_ERROR_COUNT_MASK 0x00FF
+
+ /*
+ * Prevent stats update while adapter is being reset, or if the pci
+ * connection is down.
+ */
+ if (adapter->link_speed == 0)
+ return;
+ if (pci_channel_offline(pdev))
+ return;
+
+ if (!adapter->ecdev)
+ spin_lock_irqsave(&adapter->stats_lock, flags);
+
+ /* these counters are modified from e1000_tbi_adjust_stats,
+ * called from the interrupt context, so they must only
+ * be written while holding adapter->stats_lock
+ */
+
+ adapter->stats.crcerrs += er32(CRCERRS);
+ adapter->stats.gprc += er32(GPRC);
+ adapter->stats.gorcl += er32(GORCL);
+ adapter->stats.gorch += er32(GORCH);
+ adapter->stats.bprc += er32(BPRC);
+ adapter->stats.mprc += er32(MPRC);
+ adapter->stats.roc += er32(ROC);
+
+ adapter->stats.prc64 += er32(PRC64);
+ adapter->stats.prc127 += er32(PRC127);
+ adapter->stats.prc255 += er32(PRC255);
+ adapter->stats.prc511 += er32(PRC511);
+ adapter->stats.prc1023 += er32(PRC1023);
+ adapter->stats.prc1522 += er32(PRC1522);
+
+ adapter->stats.symerrs += er32(SYMERRS);
+ adapter->stats.mpc += er32(MPC);
+ adapter->stats.scc += er32(SCC);
+ adapter->stats.ecol += er32(ECOL);
+ adapter->stats.mcc += er32(MCC);
+ adapter->stats.latecol += er32(LATECOL);
+ adapter->stats.dc += er32(DC);
+ adapter->stats.sec += er32(SEC);
+ adapter->stats.rlec += er32(RLEC);
+ adapter->stats.xonrxc += er32(XONRXC);
+ adapter->stats.xontxc += er32(XONTXC);
+ adapter->stats.xoffrxc += er32(XOFFRXC);
+ adapter->stats.xofftxc += er32(XOFFTXC);
+ adapter->stats.fcruc += er32(FCRUC);
+ adapter->stats.gptc += er32(GPTC);
+ adapter->stats.gotcl += er32(GOTCL);
+ adapter->stats.gotch += er32(GOTCH);
+ adapter->stats.rnbc += er32(RNBC);
+ adapter->stats.ruc += er32(RUC);
+ adapter->stats.rfc += er32(RFC);
+ adapter->stats.rjc += er32(RJC);
+ adapter->stats.torl += er32(TORL);
+ adapter->stats.torh += er32(TORH);
+ adapter->stats.totl += er32(TOTL);
+ adapter->stats.toth += er32(TOTH);
+ adapter->stats.tpr += er32(TPR);
+
+ adapter->stats.ptc64 += er32(PTC64);
+ adapter->stats.ptc127 += er32(PTC127);
+ adapter->stats.ptc255 += er32(PTC255);
+ adapter->stats.ptc511 += er32(PTC511);
+ adapter->stats.ptc1023 += er32(PTC1023);
+ adapter->stats.ptc1522 += er32(PTC1522);
+
+ adapter->stats.mptc += er32(MPTC);
+ adapter->stats.bptc += er32(BPTC);
+
+ /* used for adaptive IFS */
+
+ hw->tx_packet_delta = er32(TPT);
+ adapter->stats.tpt += hw->tx_packet_delta;
+ hw->collision_delta = er32(COLC);
+ adapter->stats.colc += hw->collision_delta;
+
+ if (hw->mac_type >= e1000_82543) {
+ adapter->stats.algnerrc += er32(ALGNERRC);
+ adapter->stats.rxerrc += er32(RXERRC);
+ adapter->stats.tncrs += er32(TNCRS);
+ adapter->stats.cexterr += er32(CEXTERR);
+ adapter->stats.tsctc += er32(TSCTC);
+ adapter->stats.tsctfc += er32(TSCTFC);
+ }
+
+ /* Fill out the OS statistics structure */
+ adapter->net_stats.multicast = adapter->stats.mprc;
+ adapter->net_stats.collisions = adapter->stats.colc;
+
+ /* Rx Errors */
+
+ /* RLEC on some newer hardware can be incorrect so build
+ * our own version based on RUC and ROC */
+ adapter->net_stats.rx_errors = adapter->stats.rxerrc +
+ adapter->stats.crcerrs + adapter->stats.algnerrc +
+ adapter->stats.ruc + adapter->stats.roc +
+ adapter->stats.cexterr;
+ adapter->stats.rlerrc = adapter->stats.ruc + adapter->stats.roc;
+ adapter->net_stats.rx_length_errors = adapter->stats.rlerrc;
+ adapter->net_stats.rx_crc_errors = adapter->stats.crcerrs;
+ adapter->net_stats.rx_frame_errors = adapter->stats.algnerrc;
+ adapter->net_stats.rx_missed_errors = adapter->stats.mpc;
+
+ /* Tx Errors */
+ adapter->stats.txerrc = adapter->stats.ecol + adapter->stats.latecol;
+ adapter->net_stats.tx_errors = adapter->stats.txerrc;
+ adapter->net_stats.tx_aborted_errors = adapter->stats.ecol;
+ adapter->net_stats.tx_window_errors = adapter->stats.latecol;
+ adapter->net_stats.tx_carrier_errors = adapter->stats.tncrs;
+ if (hw->bad_tx_carr_stats_fd &&
+ adapter->link_duplex == FULL_DUPLEX) {
+ adapter->net_stats.tx_carrier_errors = 0;
+ adapter->stats.tncrs = 0;
+ }
+
+ /* Tx Dropped needs to be maintained elsewhere */
+
+ /* Phy Stats */
+ if (hw->media_type == e1000_media_type_copper) {
+ if ((adapter->link_speed == SPEED_1000) &&
+ (!e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_tmp))) {
+ phy_tmp &= PHY_IDLE_ERROR_COUNT_MASK;
+ adapter->phy_stats.idle_errors += phy_tmp;
+ }
+
+ if ((hw->mac_type <= e1000_82546) &&
+ (hw->phy_type == e1000_phy_m88) &&
+ !e1000_read_phy_reg(hw, M88E1000_RX_ERR_CNTR, &phy_tmp))
+ adapter->phy_stats.receive_errors += phy_tmp;
+ }
+
+ /* Management Stats */
+ if (hw->has_smbus) {
+ adapter->stats.mgptc += er32(MGTPTC);
+ adapter->stats.mgprc += er32(MGTPRC);
+ adapter->stats.mgpdc += er32(MGTPDC);
+ }
+
+ if (!adapter->ecdev)
+ spin_unlock_irqrestore(&adapter->stats_lock, flags);
+}
+
+void ec_poll(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ if (jiffies - adapter->ec_watchdog_jiffies >= 2 * HZ) {
+ e1000_watchdog((unsigned long) adapter);
+ adapter->ec_watchdog_jiffies = jiffies;
+ }
+
+ e1000_intr(0, netdev);
+}
+
+/**
+ * e1000_intr - Interrupt Handler
+ * @irq: interrupt number
+ * @data: pointer to a network interface device structure
+ **/
+
+static irqreturn_t e1000_intr(int irq, void *data)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 icr = er32(ICR);
+
+ if (unlikely((!icr) || test_bit(__E1000_DOWN, &adapter->flags)))
+ return IRQ_NONE; /* Not our interrupt */
+
+ if (unlikely(icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC))) {
+ hw->get_link_status = 1;
+ /* guard against interrupt when we're going down */
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->watchdog_timer, jiffies + 1);
+ }
+
+ if (adapter->ecdev) {
+ int i, ec_work_done = 0;
+ for (i = 0; i < E1000_MAX_INTR; i++) {
+ if (unlikely(!adapter->clean_rx(adapter, adapter->rx_ring,
+ &ec_work_done, 100) &&
+ !e1000_clean_tx_irq(adapter, adapter->tx_ring))) {
+ break;
+ }
+ }
+ } else {
+ /* disable interrupts, without the synchronize_irq bit */
+ ew32(IMC, ~0);
+ E1000_WRITE_FLUSH();
+
+ if (likely(napi_schedule_prep(&adapter->napi))) {
+ adapter->total_tx_bytes = 0;
+ adapter->total_tx_packets = 0;
+ adapter->total_rx_bytes = 0;
+ adapter->total_rx_packets = 0;
+ __napi_schedule(&adapter->napi);
+ } else {
+ /* this really should not happen! if it does it is basically a
+ * bug, but not a hard error, so enable ints and continue */
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_enable(adapter);
+ }
+ }
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * e1000_clean - NAPI Rx polling callback
+ * @adapter: board private structure
+ * EtherCAT: never called
+ **/
+static int e1000_clean(struct napi_struct *napi, int budget)
+{
+ struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, napi);
+ int tx_clean_complete = 0, work_done = 0;
+
+ tx_clean_complete = e1000_clean_tx_irq(adapter, &adapter->tx_ring[0]);
+
+ adapter->clean_rx(adapter, &adapter->rx_ring[0], &work_done, budget);
+
+ if (!tx_clean_complete)
+ work_done = budget;
+
+ /* If budget not fully consumed, exit the polling mode */
+ if (work_done < budget) {
+ if (likely(adapter->itr_setting & 3))
+ e1000_set_itr(adapter);
+ napi_complete(napi);
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_enable(adapter);
+ }
+
+ return work_done;
+}
+
+/**
+ * e1000_clean_tx_irq - Reclaim resources after transmit completes
+ * @adapter: board private structure
+ **/
+static bool e1000_clean_tx_irq(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_tx_desc *tx_desc, *eop_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i, eop;
+ unsigned int count = 0;
+ unsigned int total_tx_bytes=0, total_tx_packets=0;
+
+ i = tx_ring->next_to_clean;
+ eop = tx_ring->buffer_info[i].next_to_watch;
+ eop_desc = E1000_TX_DESC(*tx_ring, eop);
+
+ while ((eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) &&
+ (count < tx_ring->count)) {
+ bool cleaned = false;
+ for ( ; !cleaned; count++) {
+ tx_desc = E1000_TX_DESC(*tx_ring, i);
+ buffer_info = &tx_ring->buffer_info[i];
+ cleaned = (i == eop);
+
+ if (cleaned) {
+ struct sk_buff *skb = buffer_info->skb;
+ unsigned int segs, bytecount;
+ segs = skb_shinfo(skb)->gso_segs ?: 1;
+ /* multiply data chunks by size of headers */
+ bytecount = ((segs - 1) * skb_headlen(skb)) +
+ skb->len;
+ total_tx_packets += segs;
+ total_tx_bytes += bytecount;
+ }
+ e1000_unmap_and_free_tx_resource(adapter, buffer_info);
+ tx_desc->upper.data = 0;
+
+ if (unlikely(++i == tx_ring->count)) i = 0;
+ }
+
+ eop = tx_ring->buffer_info[i].next_to_watch;
+ eop_desc = E1000_TX_DESC(*tx_ring, eop);
+ }
+
+ tx_ring->next_to_clean = i;
+
+#define TX_WAKE_THRESHOLD 32
+ if (!adapter->ecdev && unlikely(count && netif_carrier_ok(netdev) &&
+ E1000_DESC_UNUSED(tx_ring) >= TX_WAKE_THRESHOLD)) {
+ /* Make sure that anybody stopping the queue after this
+ * sees the new next_to_clean.
+ */
+ smp_mb();
+
+ if (netif_queue_stopped(netdev) &&
+ !(test_bit(__E1000_DOWN, &adapter->flags))) {
+ netif_wake_queue(netdev);
+ ++adapter->restart_queue;
+ }
+ }
+
+ if (!adapter->ecdev && adapter->detect_tx_hung) {
+ /* Detect a transmit hang in hardware, this serializes the
+ * check with the clearing of time_stamp and movement of i */
+ adapter->detect_tx_hung = false;
+ if (tx_ring->buffer_info[eop].time_stamp &&
+ time_after(jiffies, tx_ring->buffer_info[eop].time_stamp +
+ (adapter->tx_timeout_factor * HZ))
+ && !(er32(STATUS) & E1000_STATUS_TXOFF)) {
+
+ /* detected Tx unit hang */
+ DPRINTK(DRV, ERR, "Detected Tx Unit Hang\n"
+ " Tx Queue <%lu>\n"
+ " TDH <%x>\n"
+ " TDT <%x>\n"
+ " next_to_use <%x>\n"
+ " next_to_clean <%x>\n"
+ "buffer_info[next_to_clean]\n"
+ " time_stamp <%lx>\n"
+ " next_to_watch <%x>\n"
+ " jiffies <%lx>\n"
+ " next_to_watch.status <%x>\n",
+ (unsigned long)((tx_ring - adapter->tx_ring) /
+ sizeof(struct e1000_tx_ring)),
+ readl(hw->hw_addr + tx_ring->tdh),
+ readl(hw->hw_addr + tx_ring->tdt),
+ tx_ring->next_to_use,
+ tx_ring->next_to_clean,
+ tx_ring->buffer_info[eop].time_stamp,
+ eop,
+ jiffies,
+ eop_desc->upper.fields.status);
+ netif_stop_queue(netdev);
+ }
+ }
+ adapter->total_tx_bytes += total_tx_bytes;
+ adapter->total_tx_packets += total_tx_packets;
+ adapter->net_stats.tx_bytes += total_tx_bytes;
+ adapter->net_stats.tx_packets += total_tx_packets;
+ return (count < tx_ring->count);
+}
+
+/**
+ * e1000_rx_checksum - Receive Checksum Offload for 82543
+ * @adapter: board private structure
+ * @status_err: receive descriptor status and error fields
+ * @csum: receive descriptor csum field
+ * @sk_buff: socket buffer with received data
+ **/
+
+static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
+ u32 csum, struct sk_buff *skb)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 status = (u16)status_err;
+ u8 errors = (u8)(status_err >> 24);
+ skb->ip_summed = CHECKSUM_NONE;
+
+ /* 82543 or newer only */
+ if (unlikely(hw->mac_type < e1000_82543)) return;
+ /* Ignore Checksum bit is set */
+ if (unlikely(status & E1000_RXD_STAT_IXSM)) return;
+ /* TCP/UDP checksum error bit is set */
+ if (unlikely(errors & E1000_RXD_ERR_TCPE)) {
+ /* let the stack verify checksum errors */
+ adapter->hw_csum_err++;
+ return;
+ }
+ /* TCP/UDP Checksum has not been calculated */
+ if (!(status & E1000_RXD_STAT_TCPCS))
+ return;
+
+ /* It must be a TCP or UDP packet with a valid checksum */
+ if (likely(status & E1000_RXD_STAT_TCPCS)) {
+ /* TCP checksum is good */
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+ }
+ adapter->hw_csum_good++;
+}
+
+/**
+ * e1000_consume_page - helper function
+ **/
+static void e1000_consume_page(struct e1000_buffer *bi, struct sk_buff *skb,
+ u16 length)
+{
+ bi->page = NULL;
+ skb->len += length;
+ skb->data_len += length;
+ skb->truesize += length;
+}
+
+/**
+ * e1000_receive_skb - helper function to handle rx indications
+ * @adapter: board private structure
+ * @status: descriptor status field as written by hardware
+ * @vlan: descriptor vlan field as written by hardware (no le/be conversion)
+ * @skb: pointer to sk_buff to be indicated to stack
+ */
+static void e1000_receive_skb(struct e1000_adapter *adapter, u8 status,
+ __le16 vlan, struct sk_buff *skb)
+{
+ if (unlikely(adapter->vlgrp && (status & E1000_RXD_STAT_VP))) {
+ vlan_hwaccel_receive_skb(skb, adapter->vlgrp,
+ le16_to_cpu(vlan) &
+ E1000_RXD_SPC_VLAN_MASK);
+ } else {
+ netif_receive_skb(skb);
+ }
+}
+
+/**
+ * e1000_clean_jumbo_rx_irq - Send received data up the network stack; legacy
+ * @adapter: board private structure
+ * @rx_ring: ring to clean
+ * @work_done: amount of napi work completed this call
+ * @work_to_do: max amount of work allowed for this call to do
+ *
+ * the return value indicates whether actual cleaning was done, there
+ * is no guarantee that everything was cleaned
+ */
+static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int *work_done, int work_to_do)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_rx_desc *rx_desc, *next_rxd;
+ struct e1000_buffer *buffer_info, *next_buffer;
+ unsigned long irq_flags;
+ u32 length;
+ unsigned int i;
+ int cleaned_count = 0;
+ bool cleaned = false;
+ unsigned int total_rx_bytes=0, total_rx_packets=0;
+
+ i = rx_ring->next_to_clean;
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (rx_desc->status & E1000_RXD_STAT_DD) {
+ struct sk_buff *skb;
+ u8 status;
+
+ if (*work_done >= work_to_do)
+ break;
+ (*work_done)++;
+
+ status = rx_desc->status;
+ skb = buffer_info->skb;
+ if (!adapter->ecdev) buffer_info->skb = NULL;
+
+ if (++i == rx_ring->count) i = 0;
+ next_rxd = E1000_RX_DESC(*rx_ring, i);
+ prefetch(next_rxd);
+
+ next_buffer = &rx_ring->buffer_info[i];
+
+ cleaned = true;
+ cleaned_count++;
+ pci_unmap_page(pdev, buffer_info->dma, buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+ buffer_info->dma = 0;
+
+ length = le16_to_cpu(rx_desc->length);
+
+ /* errors is only valid for DD + EOP descriptors */
+ if (!adapter->ecdev &&
+ unlikely((status & E1000_RXD_STAT_EOP) &&
+ (rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK))) {
+ u8 last_byte = *(skb->data + length - 1);
+ if (TBI_ACCEPT(hw, status, rx_desc->errors, length,
+ last_byte)) {
+ spin_lock_irqsave(&adapter->stats_lock,
+ irq_flags);
+ e1000_tbi_adjust_stats(hw, &adapter->stats,
+ length, skb->data);
+ spin_unlock_irqrestore(&adapter->stats_lock,
+ irq_flags);
+ length--;
+ } else {
+ /* recycle both page and skb */
+ buffer_info->skb = skb;
+ /* an error means any chain goes out the window
+ * too */
+ if (rx_ring->rx_skb_top)
+ dev_kfree_skb(rx_ring->rx_skb_top);
+ rx_ring->rx_skb_top = NULL;
+ goto next_desc;
+ }
+ }
+
+#define rxtop rx_ring->rx_skb_top
+ if (!(status & E1000_RXD_STAT_EOP)) {
+ /* this descriptor is only the beginning (or middle) */
+ if (!rxtop) {
+ /* this is the beginning of a chain */
+ rxtop = skb;
+ skb_fill_page_desc(rxtop, 0, buffer_info->page,
+ 0, length);
+ } else {
+ /* this is the middle of a chain */
+ skb_fill_page_desc(rxtop,
+ skb_shinfo(rxtop)->nr_frags,
+ buffer_info->page, 0, length);
+ /* re-use the skb, only consumed the page */
+ buffer_info->skb = skb;
+ }
+ e1000_consume_page(buffer_info, rxtop, length);
+ goto next_desc;
+ } else {
+ if (rxtop) {
+ /* end of the chain */
+ skb_fill_page_desc(rxtop,
+ skb_shinfo(rxtop)->nr_frags,
+ buffer_info->page, 0, length);
+ /* re-use the current skb, we only consumed the
+ * page */
+ buffer_info->skb = skb;
+ skb = rxtop;
+ rxtop = NULL;
+ e1000_consume_page(buffer_info, skb, length);
+ } else {
+ /* no chain, got EOP, this buf is the packet
+ * copybreak to save the put_page/alloc_page */
+ if (length <= copybreak &&
+ skb_tailroom(skb) >= length) {
+ u8 *vaddr;
+ vaddr = kmap_atomic(buffer_info->page,
+ KM_SKB_DATA_SOFTIRQ);
+ memcpy(skb_tail_pointer(skb), vaddr, length);
+ kunmap_atomic(vaddr,
+ KM_SKB_DATA_SOFTIRQ);
+ /* re-use the page, so don't erase
+ * buffer_info->page */
+ skb_put(skb, length);
+ } else {
+ skb_fill_page_desc(skb, 0,
+ buffer_info->page, 0,
+ length);
+ e1000_consume_page(buffer_info, skb,
+ length);
+ }
+ }
+ }
+
+ /* Receive Checksum Offload XXX recompute due to CRC strip? */
+ e1000_rx_checksum(adapter,
+ (u32)(status) |
+ ((u32)(rx_desc->errors) << 24),
+ le16_to_cpu(rx_desc->csum), skb);
+
+ pskb_trim(skb, skb->len - 4);
+
+ /* probably a little skewed due to removing CRC */
+ total_rx_bytes += skb->len;
+ total_rx_packets++;
+
+ /* eth type trans needs skb->data to point to something */
+ if (!pskb_may_pull(skb, ETH_HLEN)) {
+ DPRINTK(DRV, ERR, "pskb_may_pull failed.\n");
+ if (!adapter->ecdev) dev_kfree_skb(skb);
+ goto next_desc;
+ }
+
+ if (adapter->ecdev) {
+ ecdev_receive(adapter->ecdev, skb->data, length);
+
+ // No need to detect link status as
+ // long as frames are received: Reset watchdog.
+ adapter->ec_watchdog_jiffies = jiffies;
+ } else {
+ skb->protocol = eth_type_trans(skb, netdev);
+ e1000_receive_skb(adapter, status, rx_desc->special, skb);
+ }
+next_desc:
+ rx_desc->status = 0;
+
+ /* return some buffers to hardware, one at a time is too slow */
+ if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
+ adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
+ cleaned_count = 0;
+ }
+
+ /* use prefetched values */
+ rx_desc = next_rxd;
+ buffer_info = next_buffer;
+ }
+ rx_ring->next_to_clean = i;
+
+ cleaned_count = E1000_DESC_UNUSED(rx_ring);
+ if (cleaned_count)
+ adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
+
+ adapter->total_rx_packets += total_rx_packets;
+ adapter->total_rx_bytes += total_rx_bytes;
+ adapter->net_stats.rx_bytes += total_rx_bytes;
+ adapter->net_stats.rx_packets += total_rx_packets;
+ return cleaned;
+}
+
+/**
+ * e1000_clean_rx_irq - Send received data up the network stack; legacy
+ * @adapter: board private structure
+ * @rx_ring: ring to clean
+ * @work_done: amount of napi work completed this call
+ * @work_to_do: max amount of work allowed for this call to do
+ */
+static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int *work_done, int work_to_do)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_rx_desc *rx_desc, *next_rxd;
+ struct e1000_buffer *buffer_info, *next_buffer;
+ unsigned long flags;
+ u32 length;
+ unsigned int i;
+ int cleaned_count = 0;
+ bool cleaned = false;
+ unsigned int total_rx_bytes=0, total_rx_packets=0;
+
+ i = rx_ring->next_to_clean;
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (rx_desc->status & E1000_RXD_STAT_DD) {
+ struct sk_buff *skb;
+ u8 status;
+
+ if (*work_done >= work_to_do)
+ break;
+ (*work_done)++;
+
+ status = rx_desc->status;
+ skb = buffer_info->skb;
+ if (!adapter->ecdev) buffer_info->skb = NULL;
+
+ prefetch(skb->data - NET_IP_ALIGN);
+
+ if (++i == rx_ring->count) i = 0;
+ next_rxd = E1000_RX_DESC(*rx_ring, i);
+ prefetch(next_rxd);
+
+ next_buffer = &rx_ring->buffer_info[i];
+
+ cleaned = true;
+ cleaned_count++;
+ pci_unmap_single(pdev, buffer_info->dma, buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+ buffer_info->dma = 0;
+
+ length = le16_to_cpu(rx_desc->length);
+ /* !EOP means multiple descriptors were used to store a single
+ * packet, if thats the case we need to toss it. In fact, we
+ * to toss every packet with the EOP bit clear and the next
+ * frame that _does_ have the EOP bit set, as it is by
+ * definition only a frame fragment
+ */
+ if (unlikely(!(status & E1000_RXD_STAT_EOP)))
+ adapter->discarding = true;
+
+ if (adapter->discarding) {
+ /* All receives must fit into a single buffer */
+ E1000_DBG("%s: Receive packet consumed multiple"
+ " buffers\n", netdev->name);
+ /* recycle */
+ buffer_info->skb = skb;
+ if (status & E1000_RXD_STAT_EOP)
+ adapter->discarding = false;
+ goto next_desc;
+ }
+
+ if (!adapter->ecdev &&
+ unlikely(rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK)) {
+ u8 last_byte = *(skb->data + length - 1);
+ if (TBI_ACCEPT(hw, status, rx_desc->errors, length,
+ last_byte)) {
+ spin_lock_irqsave(&adapter->stats_lock, flags);
+ e1000_tbi_adjust_stats(hw, &adapter->stats,
+ length, skb->data);
+ spin_unlock_irqrestore(&adapter->stats_lock,
+ flags);
+ length--;
+ } else {
+ /* recycle */
+ buffer_info->skb = skb;
+ goto next_desc;
+ }
+ }
+
+ /* adjust length to remove Ethernet CRC, this must be
+ * done after the TBI_ACCEPT workaround above */
+ length -= 4;
+
+ /* probably a little skewed due to removing CRC */
+ total_rx_bytes += length;
+ total_rx_packets++;
+
+ /* code added for copybreak, this should improve
+ * performance for small packets with large amounts
+ * of reassembly being done in the stack */
+ if (!adapter->ecdev && length < copybreak) {
+ struct sk_buff *new_skb =
+ netdev_alloc_skb(netdev, length + NET_IP_ALIGN);
+ if (new_skb) {
+ skb_reserve(new_skb, NET_IP_ALIGN);
+ skb_copy_to_linear_data_offset(new_skb,
+ -NET_IP_ALIGN,
+ (skb->data -
+ NET_IP_ALIGN),
+ (length +
+ NET_IP_ALIGN));
+ /* save the skb in buffer_info as good */
+ buffer_info->skb = skb;
+ skb = new_skb;
+ }
+ /* else just continue with the old one */
+ }
+ /* end copybreak code */
+ skb_put(skb, length);
+
+ /* Receive Checksum Offload */
+ e1000_rx_checksum(adapter,
+ (u32)(status) |
+ ((u32)(rx_desc->errors) << 24),
+ le16_to_cpu(rx_desc->csum), skb);
+
+ if (adapter->ecdev) {
+ ecdev_receive(adapter->ecdev, skb->data, length);
+
+ // No need to detect link status as
+ // long as frames are received: Reset watchdog.
+ adapter->ec_watchdog_jiffies = jiffies;
+ } else {
+ skb->protocol = eth_type_trans(skb, netdev);
+ e1000_receive_skb(adapter, status, rx_desc->special, skb);
+ }
+
+next_desc:
+ rx_desc->status = 0;
+
+ /* return some buffers to hardware, one at a time is too slow */
+ if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
+ adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
+ cleaned_count = 0;
+ }
+
+ /* use prefetched values */
+ rx_desc = next_rxd;
+ buffer_info = next_buffer;
+ }
+ rx_ring->next_to_clean = i;
+
+ cleaned_count = E1000_DESC_UNUSED(rx_ring);
+ if (cleaned_count)
+ adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
+
+ adapter->total_rx_packets += total_rx_packets;
+ adapter->total_rx_bytes += total_rx_bytes;
+ adapter->net_stats.rx_bytes += total_rx_bytes;
+ adapter->net_stats.rx_packets += total_rx_packets;
+ return cleaned;
+}
+
+/**
+ * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers
+ * @adapter: address of board private structure
+ * @rx_ring: pointer to receive ring structure
+ * @cleaned_count: number of buffers to allocate this pass
+ **/
+
+static void
+e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring, int cleaned_count)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_rx_desc *rx_desc;
+ struct e1000_buffer *buffer_info;
+ struct sk_buff *skb;
+ unsigned int i;
+ unsigned int bufsz = 256 -
+ 16 /*for skb_reserve */ -
+ NET_IP_ALIGN;
+
+ i = rx_ring->next_to_use;
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (cleaned_count--) {
+ skb = buffer_info->skb;
+ if (skb) {
+ skb_trim(skb, 0);
+ goto check_page;
+ }
+
+ skb = netdev_alloc_skb(netdev, bufsz);
+ if (unlikely(!skb)) {
+ /* Better luck next round */
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ /* Fix for errata 23, can't cross 64kB boundary */
+ if (!e1000_check_64k_bound(adapter, skb->data, bufsz)) {
+ struct sk_buff *oldskb = skb;
+ DPRINTK(PROBE, ERR, "skb align check failed: %u bytes "
+ "at %p\n", bufsz, skb->data);
+ /* Try again, without freeing the previous */
+ skb = netdev_alloc_skb(netdev, bufsz);
+ /* Failed allocation, critical failure */
+ if (!skb) {
+ dev_kfree_skb(oldskb);
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ if (!e1000_check_64k_bound(adapter, skb->data, bufsz)) {
+ /* give up */
+ dev_kfree_skb(skb);
+ dev_kfree_skb(oldskb);
+ break; /* while (cleaned_count--) */
+ }
+
+ /* Use new allocation */
+ dev_kfree_skb(oldskb);
+ }
+ /* Make buffer alignment 2 beyond a 16 byte boundary
+ * this will result in a 16 byte aligned IP header after
+ * the 14 byte MAC header is removed
+ */
+ skb_reserve(skb, NET_IP_ALIGN);
+
+ buffer_info->skb = skb;
+ buffer_info->length = adapter->rx_buffer_len;
+check_page:
+ /* allocate a new page if necessary */
+ if (!buffer_info->page) {
+ buffer_info->page = alloc_page(GFP_ATOMIC);
+ if (unlikely(!buffer_info->page)) {
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+ }
+
+ if (!buffer_info->dma)
+ buffer_info->dma = pci_map_page(pdev,
+ buffer_info->page, 0,
+ buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+
+ if (unlikely(++i == rx_ring->count))
+ i = 0;
+ buffer_info = &rx_ring->buffer_info[i];
+ }
+
+ if (likely(rx_ring->next_to_use != i)) {
+ rx_ring->next_to_use = i;
+ if (unlikely(i-- == 0))
+ i = (rx_ring->count - 1);
+
+ /* Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64). */
+ wmb();
+ writel(i, adapter->hw.hw_addr + rx_ring->rdt);
+ }
+}
+
+/**
+ * e1000_alloc_rx_buffers - Replace used receive buffers; legacy & extended
+ * @adapter: address of board private structure
+ **/
+
+static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int cleaned_count)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_rx_desc *rx_desc;
+ struct e1000_buffer *buffer_info;
+ struct sk_buff *skb;
+ unsigned int i;
+ unsigned int bufsz = adapter->rx_buffer_len + NET_IP_ALIGN;
+
+ i = rx_ring->next_to_use;
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (cleaned_count--) {
+ skb = buffer_info->skb;
+ if (skb) {
+ skb_trim(skb, 0);
+ goto map_skb;
+ }
+
+ skb = netdev_alloc_skb(netdev, bufsz);
+ if (unlikely(!skb)) {
+ /* Better luck next round */
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ /* Fix for errata 23, can't cross 64kB boundary */
+ if (!e1000_check_64k_bound(adapter, skb->data, bufsz)) {
+ struct sk_buff *oldskb = skb;
+ DPRINTK(RX_ERR, ERR, "skb align check failed: %u bytes "
+ "at %p\n", bufsz, skb->data);
+ /* Try again, without freeing the previous */
+ skb = netdev_alloc_skb(netdev, bufsz);
+ /* Failed allocation, critical failure */
+ if (!skb) {
+ dev_kfree_skb(oldskb);
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ if (!e1000_check_64k_bound(adapter, skb->data, bufsz)) {
+ /* give up */
+ dev_kfree_skb(skb);
+ dev_kfree_skb(oldskb);
+ adapter->alloc_rx_buff_failed++;
+ break; /* while !buffer_info->skb */
+ }
+
+ /* Use new allocation */
+ dev_kfree_skb(oldskb);
+ }
+ /* Make buffer alignment 2 beyond a 16 byte boundary
+ * this will result in a 16 byte aligned IP header after
+ * the 14 byte MAC header is removed
+ */
+ skb_reserve(skb, NET_IP_ALIGN);
+
+ buffer_info->skb = skb;
+ buffer_info->length = adapter->rx_buffer_len;
+map_skb:
+ buffer_info->dma = pci_map_single(pdev,
+ skb->data,
+ buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+
+ /*
+ * XXX if it was allocated cleanly it will never map to a
+ * boundary crossing
+ */
+
+ /* Fix for errata 23, can't cross 64kB boundary */
+ if (!e1000_check_64k_bound(adapter,
+ (void *)(unsigned long)buffer_info->dma,
+ adapter->rx_buffer_len)) {
+ DPRINTK(RX_ERR, ERR,
+ "dma align check failed: %u bytes at %p\n",
+ adapter->rx_buffer_len,
+ (void *)(unsigned long)buffer_info->dma);
+ if (!adapter->ecdev) {
+ dev_kfree_skb(skb);
+ buffer_info->skb = NULL;
+ }
+
+ pci_unmap_single(pdev, buffer_info->dma,
+ adapter->rx_buffer_len,
+ PCI_DMA_FROMDEVICE);
+ buffer_info->dma = 0;
+
+ adapter->alloc_rx_buff_failed++;
+ break; /* while !buffer_info->skb */
+ }
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+
+ if (unlikely(++i == rx_ring->count))
+ i = 0;
+ buffer_info = &rx_ring->buffer_info[i];
+ }
+
+ if (likely(rx_ring->next_to_use != i)) {
+ rx_ring->next_to_use = i;
+ if (unlikely(i-- == 0))
+ i = (rx_ring->count - 1);
+
+ /* Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64). */
+ wmb();
+ writel(i, hw->hw_addr + rx_ring->rdt);
+ }
+}
+
+/**
+ * e1000_smartspeed - Workaround for SmartSpeed on 82541 and 82547 controllers.
+ * @adapter:
+ **/
+
+static void e1000_smartspeed(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 phy_status;
+ u16 phy_ctrl;
+
+ if ((hw->phy_type != e1000_phy_igp) || !hw->autoneg ||
+ !(hw->autoneg_advertised & ADVERTISE_1000_FULL))
+ return;
+
+ if (adapter->smartspeed == 0) {
+ /* If Master/Slave config fault is asserted twice,
+ * we assume back-to-back */
+ e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_status);
+ if (!(phy_status & SR_1000T_MS_CONFIG_FAULT)) return;
+ e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_status);
+ if (!(phy_status & SR_1000T_MS_CONFIG_FAULT)) return;
+ e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_ctrl);
+ if (phy_ctrl & CR_1000T_MS_ENABLE) {
+ phy_ctrl &= ~CR_1000T_MS_ENABLE;
+ e1000_write_phy_reg(hw, PHY_1000T_CTRL,
+ phy_ctrl);
+ adapter->smartspeed++;
+ if (!e1000_phy_setup_autoneg(hw) &&
+ !e1000_read_phy_reg(hw, PHY_CTRL,
+ &phy_ctrl)) {
+ phy_ctrl |= (MII_CR_AUTO_NEG_EN |
+ MII_CR_RESTART_AUTO_NEG);
+ e1000_write_phy_reg(hw, PHY_CTRL,
+ phy_ctrl);
+ }
+ }
+ return;
+ } else if (adapter->smartspeed == E1000_SMARTSPEED_DOWNSHIFT) {
+ /* If still no link, perhaps using 2/3 pair cable */
+ e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_ctrl);
+ phy_ctrl |= CR_1000T_MS_ENABLE;
+ e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_ctrl);
+ if (!e1000_phy_setup_autoneg(hw) &&
+ !e1000_read_phy_reg(hw, PHY_CTRL, &phy_ctrl)) {
+ phy_ctrl |= (MII_CR_AUTO_NEG_EN |
+ MII_CR_RESTART_AUTO_NEG);
+ e1000_write_phy_reg(hw, PHY_CTRL, phy_ctrl);
+ }
+ }
+ /* Restart process after E1000_SMARTSPEED_MAX iterations */
+ if (adapter->smartspeed++ == E1000_SMARTSPEED_MAX)
+ adapter->smartspeed = 0;
+}
+
+/**
+ * e1000_ioctl -
+ * @netdev:
+ * @ifreq:
+ * @cmd:
+ **/
+
+static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
+{
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ case SIOCGMIIREG:
+ case SIOCSMIIREG:
+ return e1000_mii_ioctl(netdev, ifr, cmd);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+/**
+ * e1000_mii_ioctl -
+ * @netdev:
+ * @ifreq:
+ * @cmd:
+ **/
+
+static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
+ int cmd)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct mii_ioctl_data *data = if_mii(ifr);
+ int retval;
+ u16 mii_reg;
+ u16 spddplx;
+ unsigned long flags;
+
+ if (hw->media_type != e1000_media_type_copper)
+ return -EOPNOTSUPP;
+
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ data->phy_id = hw->phy_addr;
+ break;
+ case SIOCGMIIREG:
+ if (adapter->ecdev) return -EPERM;
+ spin_lock_irqsave(&adapter->stats_lock, flags);
+ if (e1000_read_phy_reg(hw, data->reg_num & 0x1F,
+ &data->val_out)) {
+ spin_unlock_irqrestore(&adapter->stats_lock, flags);
+ return -EIO;
+ }
+ spin_unlock_irqrestore(&adapter->stats_lock, flags);
+ break;
+ case SIOCSMIIREG:
+ if (adapter->ecdev) return -EPERM;
+ if (data->reg_num & ~(0x1F))
+ return -EFAULT;
+ mii_reg = data->val_in;
+ spin_lock_irqsave(&adapter->stats_lock, flags);
+ if (e1000_write_phy_reg(hw, data->reg_num,
+ mii_reg)) {
+ spin_unlock_irqrestore(&adapter->stats_lock, flags);
+ return -EIO;
+ }
+ spin_unlock_irqrestore(&adapter->stats_lock, flags);
+ if (hw->media_type == e1000_media_type_copper) {
+ switch (data->reg_num) {
+ case PHY_CTRL:
+ if (mii_reg & MII_CR_POWER_DOWN)
+ break;
+ if (mii_reg & MII_CR_AUTO_NEG_EN) {
+ hw->autoneg = 1;
+ hw->autoneg_advertised = 0x2F;
+ } else {
+ if (mii_reg & 0x40)
+ spddplx = SPEED_1000;
+ else if (mii_reg & 0x2000)
+ spddplx = SPEED_100;
+ else
+ spddplx = SPEED_10;
+ spddplx += (mii_reg & 0x100)
+ ? DUPLEX_FULL :
+ DUPLEX_HALF;
+ retval = e1000_set_spd_dplx(adapter,
+ spddplx);
+ if (retval)
+ return retval;
+ }
+ if (netif_running(adapter->netdev))
+ e1000_reinit_locked(adapter);
+ else
+ e1000_reset(adapter);
+ break;
+ case M88E1000_PHY_SPEC_CTRL:
+ case M88E1000_EXT_PHY_SPEC_CTRL:
+ if (e1000_phy_reset(hw))
+ return -EIO;
+ break;
+ }
+ } else {
+ switch (data->reg_num) {
+ case PHY_CTRL:
+ if (mii_reg & MII_CR_POWER_DOWN)
+ break;
+ if (netif_running(adapter->netdev))
+ e1000_reinit_locked(adapter);
+ else
+ e1000_reset(adapter);
+ break;
+ }
+ }
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+ return E1000_SUCCESS;
+}
+
+void e1000_pci_set_mwi(struct e1000_hw *hw)
+{
+ struct e1000_adapter *adapter = hw->back;
+ int ret_val = pci_set_mwi(adapter->pdev);
+
+ if (ret_val)
+ DPRINTK(PROBE, ERR, "Error in setting MWI\n");
+}
+
+void e1000_pci_clear_mwi(struct e1000_hw *hw)
+{
+ struct e1000_adapter *adapter = hw->back;
+
+ pci_clear_mwi(adapter->pdev);
+}
+
+int e1000_pcix_get_mmrbc(struct e1000_hw *hw)
+{
+ struct e1000_adapter *adapter = hw->back;
+ return pcix_get_mmrbc(adapter->pdev);
+}
+
+void e1000_pcix_set_mmrbc(struct e1000_hw *hw, int mmrbc)
+{
+ struct e1000_adapter *adapter = hw->back;
+ pcix_set_mmrbc(adapter->pdev, mmrbc);
+}
+
+void e1000_io_write(struct e1000_hw *hw, unsigned long port, u32 value)
+{
+ outl(value, port);
+}
+
+static void e1000_vlan_rx_register(struct net_device *netdev,
+ struct vlan_group *grp)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl, rctl;
+
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_disable(adapter);
+ adapter->vlgrp = grp;
+
+ if (grp) {
+ /* enable VLAN tag insert/strip */
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_VME;
+ ew32(CTRL, ctrl);
+
+ /* enable VLAN receive filtering */
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_CFIEN;
+ if (!(netdev->flags & IFF_PROMISC))
+ rctl |= E1000_RCTL_VFE;
+ ew32(RCTL, rctl);
+ e1000_update_mng_vlan(adapter);
+ } else {
+ /* disable VLAN tag insert/strip */
+ ctrl = er32(CTRL);
+ ctrl &= ~E1000_CTRL_VME;
+ ew32(CTRL, ctrl);
+
+ /* disable VLAN receive filtering */
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_VFE;
+ ew32(RCTL, rctl);
+
+ if (adapter->mng_vlan_id != (u16)E1000_MNG_VLAN_NONE) {
+ e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+ }
+ }
+
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_enable(adapter);
+}
+
+static void e1000_vlan_rx_add_vid(struct net_device *netdev, u16 vid)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 vfta, index;
+
+ if ((hw->mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
+ (vid == adapter->mng_vlan_id))
+ return;
+ /* add VID to filter table */
+ index = (vid >> 5) & 0x7F;
+ vfta = E1000_READ_REG_ARRAY(hw, VFTA, index);
+ vfta |= (1 << (vid & 0x1F));
+ e1000_write_vfta(hw, index, vfta);
+}
+
+static void e1000_vlan_rx_kill_vid(struct net_device *netdev, u16 vid)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 vfta, index;
+
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_disable(adapter);
+ vlan_group_set_device(adapter->vlgrp, vid, NULL);
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_enable(adapter);
+
+ /* remove VID from filter table */
+ index = (vid >> 5) & 0x7F;
+ vfta = E1000_READ_REG_ARRAY(hw, VFTA, index);
+ vfta &= ~(1 << (vid & 0x1F));
+ e1000_write_vfta(hw, index, vfta);
+}
+
+static void e1000_restore_vlan(struct e1000_adapter *adapter)
+{
+ e1000_vlan_rx_register(adapter->netdev, adapter->vlgrp);
+
+ if (adapter->vlgrp) {
+ u16 vid;
+ for (vid = 0; vid < VLAN_GROUP_ARRAY_LEN; vid++) {
+ if (!vlan_group_get_device(adapter->vlgrp, vid))
+ continue;
+ e1000_vlan_rx_add_vid(adapter->netdev, vid);
+ }
+ }
+}
+
+int e1000_set_spd_dplx(struct e1000_adapter *adapter, u16 spddplx)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ hw->autoneg = 0;
+
+ /* Fiber NICs only allow 1000 gbps Full duplex */
+ if ((hw->media_type == e1000_media_type_fiber) &&
+ spddplx != (SPEED_1000 + DUPLEX_FULL)) {
+ DPRINTK(PROBE, ERR, "Unsupported Speed/Duplex configuration\n");
+ return -EINVAL;
+ }
+
+ switch (spddplx) {
+ case SPEED_10 + DUPLEX_HALF:
+ hw->forced_speed_duplex = e1000_10_half;
+ break;
+ case SPEED_10 + DUPLEX_FULL:
+ hw->forced_speed_duplex = e1000_10_full;
+ break;
+ case SPEED_100 + DUPLEX_HALF:
+ hw->forced_speed_duplex = e1000_100_half;
+ break;
+ case SPEED_100 + DUPLEX_FULL:
+ hw->forced_speed_duplex = e1000_100_full;
+ break;
+ case SPEED_1000 + DUPLEX_FULL:
+ hw->autoneg = 1;
+ hw->autoneg_advertised = ADVERTISE_1000_FULL;
+ break;
+ case SPEED_1000 + DUPLEX_HALF: /* not supported */
+ default:
+ DPRINTK(PROBE, ERR, "Unsupported Speed/Duplex configuration\n");
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl, ctrl_ext, rctl, status;
+ u32 wufc = adapter->wol;
+#ifdef CONFIG_PM
+ int retval = 0;
+#endif
+
+ if (adapter->ecdev)
+ return -EBUSY;
+
+ netif_device_detach(netdev);
+
+ if (netif_running(netdev)) {
+ WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
+ e1000_down(adapter);
+ }
+
+#ifdef CONFIG_PM
+ retval = pci_save_state(pdev);
+ if (retval)
+ return retval;
+#endif
+
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU)
+ wufc &= ~E1000_WUFC_LNKC;
+
+ if (wufc) {
+ e1000_setup_rctl(adapter);
+ e1000_set_rx_mode(netdev);
+
+ /* turn on all-multi mode if wake on multicast is enabled */
+ if (wufc & E1000_WUFC_MC) {
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_MPE;
+ ew32(RCTL, rctl);
+ }
+
+ if (hw->mac_type >= e1000_82540) {
+ ctrl = er32(CTRL);
+ /* advertise wake from D3Cold */
+ #define E1000_CTRL_ADVD3WUC 0x00100000
+ /* phy power management enable */
+ #define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000
+ ctrl |= E1000_CTRL_ADVD3WUC |
+ E1000_CTRL_EN_PHY_PWR_MGMT;
+ ew32(CTRL, ctrl);
+ }
+
+ if (hw->media_type == e1000_media_type_fiber ||
+ hw->media_type == e1000_media_type_internal_serdes) {
+ /* keep the laser running in D3 */
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_SDP7_DATA;
+ ew32(CTRL_EXT, ctrl_ext);
+ }
+
+ ew32(WUC, E1000_WUC_PME_EN);
+ ew32(WUFC, wufc);
+ } else {
+ ew32(WUC, 0);
+ ew32(WUFC, 0);
+ }
+
+ e1000_release_manageability(adapter);
+
+ *enable_wake = !!wufc;
+
+ /* make sure adapter isn't asleep if manageability is enabled */
+ if (adapter->en_mng_pt)
+ *enable_wake = true;
+
+ if (netif_running(netdev))
+ e1000_free_irq(adapter);
+
+ pci_disable_device(pdev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ int retval;
+ bool wake;
+
+ retval = __e1000_shutdown(pdev, &wake);
+ if (retval)
+ return retval;
+
+ if (wake) {
+ pci_prepare_to_sleep(pdev);
+ } else {
+ pci_wake_from_d3(pdev, false);
+ pci_set_power_state(pdev, PCI_D3hot);
+ }
+
+ return 0;
+}
+
+static int e1000_resume(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 err;
+
+ if (adapter->ecdev)
+ return -EBUSY;
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+
+ if (adapter->need_ioport)
+ err = pci_enable_device(pdev);
+ else
+ err = pci_enable_device_mem(pdev);
+ if (err) {
+ printk(KERN_ERR "e1000: Cannot enable PCI device from suspend\n");
+ return err;
+ }
+ pci_set_master(pdev);
+
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ pci_enable_wake(pdev, PCI_D3cold, 0);
+
+ if (netif_running(netdev)) {
+ err = e1000_request_irq(adapter);
+ if (err)
+ return err;
+ }
+
+ e1000_power_up_phy(adapter);
+ e1000_reset(adapter);
+ ew32(WUS, ~0);
+
+ e1000_init_manageability(adapter);
+
+ if (netif_running(netdev))
+ e1000_up(adapter);
+
+ if (!adapter->ecdev) netif_device_attach(netdev);
+
+ return 0;
+}
+#endif
+
+static void e1000_shutdown(struct pci_dev *pdev)
+{
+ bool wake;
+
+ __e1000_shutdown(pdev, &wake);
+
+ if (system_state == SYSTEM_POWER_OFF) {
+ pci_wake_from_d3(pdev, wake);
+ pci_set_power_state(pdev, PCI_D3hot);
+ }
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+/*
+ * Polling 'interrupt' - used by things like netconsole to send skbs
+ * without having to re-enable interrupts. It's not called while
+ * the interrupt routine is executing.
+ */
+static void e1000_netpoll(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ disable_irq(adapter->pdev->irq);
+ e1000_intr(adapter->pdev->irq, netdev);
+ enable_irq(adapter->pdev->irq);
+}
+#endif
+
+/**
+ * e1000_io_error_detected - called when PCI error is detected
+ * @pdev: Pointer to PCI device
+ * @state: The current pci connection state
+ *
+ * This function is called after a PCI bus error affecting
+ * this device has been detected.
+ */
+static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
+ pci_channel_state_t state)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ netif_device_detach(netdev);
+
+ if (state == pci_channel_io_perm_failure)
+ return PCI_ERS_RESULT_DISCONNECT;
+
+ if (netif_running(netdev))
+ e1000_down(adapter);
+ pci_disable_device(pdev);
+
+ /* Request a slot slot reset. */
+ return PCI_ERS_RESULT_NEED_RESET;
+}
+
+/**
+ * e1000_io_slot_reset - called after the pci bus has been reset.
+ * @pdev: Pointer to PCI device
+ *
+ * Restart the card from scratch, as if from a cold-boot. Implementation
+ * resembles the first-half of the e1000_resume routine.
+ */
+static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ int err;
+
+ if (adapter->need_ioport)
+ err = pci_enable_device(pdev);
+ else
+ err = pci_enable_device_mem(pdev);
+ if (err) {
+ printk(KERN_ERR "e1000: Cannot re-enable PCI device after reset.\n");
+ return PCI_ERS_RESULT_DISCONNECT;
+ }
+ pci_set_master(pdev);
+
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ pci_enable_wake(pdev, PCI_D3cold, 0);
+
+ e1000_reset(adapter);
+ ew32(WUS, ~0);
+
+ return PCI_ERS_RESULT_RECOVERED;
+}
+
+/**
+ * e1000_io_resume - called when traffic can start flowing again.
+ * @pdev: Pointer to PCI device
+ *
+ * This callback is called when the error recovery driver tells us that
+ * its OK to resume normal operation. Implementation resembles the
+ * second-half of the e1000_resume routine.
+ */
+static void e1000_io_resume(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ e1000_init_manageability(adapter);
+
+ if (netif_running(netdev)) {
+ if (e1000_up(adapter)) {
+ printk("e1000: can't bring device back up after reset\n");
+ return;
+ }
+ }
+
+ netif_device_attach(netdev);
+}
+
+/* e1000_main.c */
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_main-2.6.32-orig.c Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,4739 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#include "e1000.h"
+#include <net/ip6_checksum.h>
+
+char e1000_driver_name[] = "e1000";
+static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
+#define DRV_VERSION "7.3.21-k5-NAPI"
+const char e1000_driver_version[] = DRV_VERSION;
+static const char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
+
+/* e1000_pci_tbl - PCI Device ID Table
+ *
+ * Last entry must be all 0s
+ *
+ * Macro expands to...
+ * {PCI_DEVICE(PCI_VENDOR_ID_INTEL, device_id)}
+ */
+static struct pci_device_id e1000_pci_tbl[] = {
+ INTEL_E1000_ETHERNET_DEVICE(0x1000),
+ INTEL_E1000_ETHERNET_DEVICE(0x1001),
+ INTEL_E1000_ETHERNET_DEVICE(0x1004),
+ INTEL_E1000_ETHERNET_DEVICE(0x1008),
+ INTEL_E1000_ETHERNET_DEVICE(0x1009),
+ INTEL_E1000_ETHERNET_DEVICE(0x100C),
+ INTEL_E1000_ETHERNET_DEVICE(0x100D),
+ INTEL_E1000_ETHERNET_DEVICE(0x100E),
+ INTEL_E1000_ETHERNET_DEVICE(0x100F),
+ INTEL_E1000_ETHERNET_DEVICE(0x1010),
+ INTEL_E1000_ETHERNET_DEVICE(0x1011),
+ INTEL_E1000_ETHERNET_DEVICE(0x1012),
+ INTEL_E1000_ETHERNET_DEVICE(0x1013),
+ INTEL_E1000_ETHERNET_DEVICE(0x1014),
+ INTEL_E1000_ETHERNET_DEVICE(0x1015),
+ INTEL_E1000_ETHERNET_DEVICE(0x1016),
+ INTEL_E1000_ETHERNET_DEVICE(0x1017),
+ INTEL_E1000_ETHERNET_DEVICE(0x1018),
+ INTEL_E1000_ETHERNET_DEVICE(0x1019),
+ INTEL_E1000_ETHERNET_DEVICE(0x101A),
+ INTEL_E1000_ETHERNET_DEVICE(0x101D),
+ INTEL_E1000_ETHERNET_DEVICE(0x101E),
+ INTEL_E1000_ETHERNET_DEVICE(0x1026),
+ INTEL_E1000_ETHERNET_DEVICE(0x1027),
+ INTEL_E1000_ETHERNET_DEVICE(0x1028),
+ INTEL_E1000_ETHERNET_DEVICE(0x1075),
+ INTEL_E1000_ETHERNET_DEVICE(0x1076),
+ INTEL_E1000_ETHERNET_DEVICE(0x1077),
+ INTEL_E1000_ETHERNET_DEVICE(0x1078),
+ INTEL_E1000_ETHERNET_DEVICE(0x1079),
+ INTEL_E1000_ETHERNET_DEVICE(0x107A),
+ INTEL_E1000_ETHERNET_DEVICE(0x107B),
+ INTEL_E1000_ETHERNET_DEVICE(0x107C),
+ INTEL_E1000_ETHERNET_DEVICE(0x108A),
+ INTEL_E1000_ETHERNET_DEVICE(0x1099),
+ INTEL_E1000_ETHERNET_DEVICE(0x10B5),
+ /* required last entry */
+ {0,}
+};
+
+MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
+
+int e1000_up(struct e1000_adapter *adapter);
+void e1000_down(struct e1000_adapter *adapter);
+void e1000_reinit_locked(struct e1000_adapter *adapter);
+void e1000_reset(struct e1000_adapter *adapter);
+int e1000_set_spd_dplx(struct e1000_adapter *adapter, u16 spddplx);
+int e1000_setup_all_tx_resources(struct e1000_adapter *adapter);
+int e1000_setup_all_rx_resources(struct e1000_adapter *adapter);
+void e1000_free_all_tx_resources(struct e1000_adapter *adapter);
+void e1000_free_all_rx_resources(struct e1000_adapter *adapter);
+static int e1000_setup_tx_resources(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *txdr);
+static int e1000_setup_rx_resources(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rxdr);
+static void e1000_free_tx_resources(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring);
+static void e1000_free_rx_resources(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring);
+void e1000_update_stats(struct e1000_adapter *adapter);
+
+static int e1000_init_module(void);
+static void e1000_exit_module(void);
+static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent);
+static void __devexit e1000_remove(struct pci_dev *pdev);
+static int e1000_alloc_queues(struct e1000_adapter *adapter);
+static int e1000_sw_init(struct e1000_adapter *adapter);
+static int e1000_open(struct net_device *netdev);
+static int e1000_close(struct net_device *netdev);
+static void e1000_configure_tx(struct e1000_adapter *adapter);
+static void e1000_configure_rx(struct e1000_adapter *adapter);
+static void e1000_setup_rctl(struct e1000_adapter *adapter);
+static void e1000_clean_all_tx_rings(struct e1000_adapter *adapter);
+static void e1000_clean_all_rx_rings(struct e1000_adapter *adapter);
+static void e1000_clean_tx_ring(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring);
+static void e1000_clean_rx_ring(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring);
+static void e1000_set_rx_mode(struct net_device *netdev);
+static void e1000_update_phy_info(unsigned long data);
+static void e1000_watchdog(unsigned long data);
+static void e1000_82547_tx_fifo_stall(unsigned long data);
+static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
+ struct net_device *netdev);
+static struct net_device_stats * e1000_get_stats(struct net_device *netdev);
+static int e1000_change_mtu(struct net_device *netdev, int new_mtu);
+static int e1000_set_mac(struct net_device *netdev, void *p);
+static irqreturn_t e1000_intr(int irq, void *data);
+static bool e1000_clean_tx_irq(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring);
+static int e1000_clean(struct napi_struct *napi, int budget);
+static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int *work_done, int work_to_do);
+static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int *work_done, int work_to_do);
+static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int cleaned_count);
+static void e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int cleaned_count);
+static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd);
+static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
+ int cmd);
+static void e1000_enter_82542_rst(struct e1000_adapter *adapter);
+static void e1000_leave_82542_rst(struct e1000_adapter *adapter);
+static void e1000_tx_timeout(struct net_device *dev);
+static void e1000_reset_task(struct work_struct *work);
+static void e1000_smartspeed(struct e1000_adapter *adapter);
+static int e1000_82547_fifo_workaround(struct e1000_adapter *adapter,
+ struct sk_buff *skb);
+
+static void e1000_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp);
+static void e1000_vlan_rx_add_vid(struct net_device *netdev, u16 vid);
+static void e1000_vlan_rx_kill_vid(struct net_device *netdev, u16 vid);
+static void e1000_restore_vlan(struct e1000_adapter *adapter);
+
+#ifdef CONFIG_PM
+static int e1000_suspend(struct pci_dev *pdev, pm_message_t state);
+static int e1000_resume(struct pci_dev *pdev);
+#endif
+static void e1000_shutdown(struct pci_dev *pdev);
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+/* for netdump / net console */
+static void e1000_netpoll (struct net_device *netdev);
+#endif
+
+#define COPYBREAK_DEFAULT 256
+static unsigned int copybreak __read_mostly = COPYBREAK_DEFAULT;
+module_param(copybreak, uint, 0644);
+MODULE_PARM_DESC(copybreak,
+ "Maximum size of packet that is copied to a new buffer on receive");
+
+static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
+ pci_channel_state_t state);
+static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev);
+static void e1000_io_resume(struct pci_dev *pdev);
+
+static struct pci_error_handlers e1000_err_handler = {
+ .error_detected = e1000_io_error_detected,
+ .slot_reset = e1000_io_slot_reset,
+ .resume = e1000_io_resume,
+};
+
+static struct pci_driver e1000_driver = {
+ .name = e1000_driver_name,
+ .id_table = e1000_pci_tbl,
+ .probe = e1000_probe,
+ .remove = __devexit_p(e1000_remove),
+#ifdef CONFIG_PM
+ /* Power Managment Hooks */
+ .suspend = e1000_suspend,
+ .resume = e1000_resume,
+#endif
+ .shutdown = e1000_shutdown,
+ .err_handler = &e1000_err_handler
+};
+
+MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
+MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+static int debug = NETIF_MSG_DRV | NETIF_MSG_PROBE;
+module_param(debug, int, 0);
+MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
+
+/**
+ * e1000_init_module - Driver Registration Routine
+ *
+ * e1000_init_module is the first routine called when the driver is
+ * loaded. All it does is register with the PCI subsystem.
+ **/
+
+static int __init e1000_init_module(void)
+{
+ int ret;
+ printk(KERN_INFO "%s - version %s\n",
+ e1000_driver_string, e1000_driver_version);
+
+ printk(KERN_INFO "%s\n", e1000_copyright);
+
+ ret = pci_register_driver(&e1000_driver);
+ if (copybreak != COPYBREAK_DEFAULT) {
+ if (copybreak == 0)
+ printk(KERN_INFO "e1000: copybreak disabled\n");
+ else
+ printk(KERN_INFO "e1000: copybreak enabled for "
+ "packets <= %u bytes\n", copybreak);
+ }
+ return ret;
+}
+
+module_init(e1000_init_module);
+
+/**
+ * e1000_exit_module - Driver Exit Cleanup Routine
+ *
+ * e1000_exit_module is called just before the driver is removed
+ * from memory.
+ **/
+
+static void __exit e1000_exit_module(void)
+{
+ pci_unregister_driver(&e1000_driver);
+}
+
+module_exit(e1000_exit_module);
+
+static int e1000_request_irq(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ irq_handler_t handler = e1000_intr;
+ int irq_flags = IRQF_SHARED;
+ int err;
+
+ err = request_irq(adapter->pdev->irq, handler, irq_flags, netdev->name,
+ netdev);
+ if (err) {
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate interrupt Error: %d\n", err);
+ }
+
+ return err;
+}
+
+static void e1000_free_irq(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+
+ free_irq(adapter->pdev->irq, netdev);
+}
+
+/**
+ * e1000_irq_disable - Mask off interrupt generation on the NIC
+ * @adapter: board private structure
+ **/
+
+static void e1000_irq_disable(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ ew32(IMC, ~0);
+ E1000_WRITE_FLUSH();
+ synchronize_irq(adapter->pdev->irq);
+}
+
+/**
+ * e1000_irq_enable - Enable default interrupt generation settings
+ * @adapter: board private structure
+ **/
+
+static void e1000_irq_enable(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ ew32(IMS, IMS_ENABLE_MASK);
+ E1000_WRITE_FLUSH();
+}
+
+static void e1000_update_mng_vlan(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u16 vid = hw->mng_cookie.vlan_id;
+ u16 old_vid = adapter->mng_vlan_id;
+ if (adapter->vlgrp) {
+ if (!vlan_group_get_device(adapter->vlgrp, vid)) {
+ if (hw->mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) {
+ e1000_vlan_rx_add_vid(netdev, vid);
+ adapter->mng_vlan_id = vid;
+ } else
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+
+ if ((old_vid != (u16)E1000_MNG_VLAN_NONE) &&
+ (vid != old_vid) &&
+ !vlan_group_get_device(adapter->vlgrp, old_vid))
+ e1000_vlan_rx_kill_vid(netdev, old_vid);
+ } else
+ adapter->mng_vlan_id = vid;
+ }
+}
+
+static void e1000_init_manageability(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (adapter->en_mng_pt) {
+ u32 manc = er32(MANC);
+
+ /* disable hardware interception of ARP */
+ manc &= ~(E1000_MANC_ARP_EN);
+
+ ew32(MANC, manc);
+ }
+}
+
+static void e1000_release_manageability(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (adapter->en_mng_pt) {
+ u32 manc = er32(MANC);
+
+ /* re-enable hardware interception of ARP */
+ manc |= E1000_MANC_ARP_EN;
+
+ ew32(MANC, manc);
+ }
+}
+
+/**
+ * e1000_configure - configure the hardware for RX and TX
+ * @adapter = private board structure
+ **/
+static void e1000_configure(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ int i;
+
+ e1000_set_rx_mode(netdev);
+
+ e1000_restore_vlan(adapter);
+ e1000_init_manageability(adapter);
+
+ e1000_configure_tx(adapter);
+ e1000_setup_rctl(adapter);
+ e1000_configure_rx(adapter);
+ /* call E1000_DESC_UNUSED which always leaves
+ * at least 1 descriptor unused to make sure
+ * next_to_use != next_to_clean */
+ for (i = 0; i < adapter->num_rx_queues; i++) {
+ struct e1000_rx_ring *ring = &adapter->rx_ring[i];
+ adapter->alloc_rx_buf(adapter, ring,
+ E1000_DESC_UNUSED(ring));
+ }
+
+ adapter->tx_queue_len = netdev->tx_queue_len;
+}
+
+int e1000_up(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ /* hardware has been reset, we need to reload some things */
+ e1000_configure(adapter);
+
+ clear_bit(__E1000_DOWN, &adapter->flags);
+
+ napi_enable(&adapter->napi);
+
+ e1000_irq_enable(adapter);
+
+ netif_wake_queue(adapter->netdev);
+
+ /* fire a link change interrupt to start the watchdog */
+ ew32(ICS, E1000_ICS_LSC);
+ return 0;
+}
+
+/**
+ * e1000_power_up_phy - restore link in case the phy was powered down
+ * @adapter: address of board private structure
+ *
+ * The phy may be powered down to save power and turn off link when the
+ * driver is unloaded and wake on lan is not enabled (among others)
+ * *** this routine MUST be followed by a call to e1000_reset ***
+ *
+ **/
+
+void e1000_power_up_phy(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 mii_reg = 0;
+
+ /* Just clear the power down bit to wake the phy back up */
+ if (hw->media_type == e1000_media_type_copper) {
+ /* according to the manual, the phy will retain its
+ * settings across a power-down/up cycle */
+ e1000_read_phy_reg(hw, PHY_CTRL, &mii_reg);
+ mii_reg &= ~MII_CR_POWER_DOWN;
+ e1000_write_phy_reg(hw, PHY_CTRL, mii_reg);
+ }
+}
+
+static void e1000_power_down_phy(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ /* Power down the PHY so no link is implied when interface is down *
+ * The PHY cannot be powered down if any of the following is true *
+ * (a) WoL is enabled
+ * (b) AMT is active
+ * (c) SoL/IDER session is active */
+ if (!adapter->wol && hw->mac_type >= e1000_82540 &&
+ hw->media_type == e1000_media_type_copper) {
+ u16 mii_reg = 0;
+
+ switch (hw->mac_type) {
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ if (er32(MANC) & E1000_MANC_SMBUS_EN)
+ goto out;
+ break;
+ default:
+ goto out;
+ }
+ e1000_read_phy_reg(hw, PHY_CTRL, &mii_reg);
+ mii_reg |= MII_CR_POWER_DOWN;
+ e1000_write_phy_reg(hw, PHY_CTRL, mii_reg);
+ mdelay(1);
+ }
+out:
+ return;
+}
+
+void e1000_down(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u32 rctl, tctl;
+
+ /* signal that we're down so the interrupt handler does not
+ * reschedule our watchdog timer */
+ set_bit(__E1000_DOWN, &adapter->flags);
+
+ /* disable receives in the hardware */
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ /* flush and sleep below */
+
+ netif_tx_disable(netdev);
+
+ /* disable transmits in the hardware */
+ tctl = er32(TCTL);
+ tctl &= ~E1000_TCTL_EN;
+ ew32(TCTL, tctl);
+ /* flush both disables and wait for them to finish */
+ E1000_WRITE_FLUSH();
+ msleep(10);
+
+ napi_disable(&adapter->napi);
+
+ e1000_irq_disable(adapter);
+
+ del_timer_sync(&adapter->tx_fifo_stall_timer);
+ del_timer_sync(&adapter->watchdog_timer);
+ del_timer_sync(&adapter->phy_info_timer);
+
+ netdev->tx_queue_len = adapter->tx_queue_len;
+ adapter->link_speed = 0;
+ adapter->link_duplex = 0;
+ netif_carrier_off(netdev);
+
+ e1000_reset(adapter);
+ e1000_clean_all_tx_rings(adapter);
+ e1000_clean_all_rx_rings(adapter);
+}
+
+void e1000_reinit_locked(struct e1000_adapter *adapter)
+{
+ WARN_ON(in_interrupt());
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+ e1000_down(adapter);
+ e1000_up(adapter);
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+}
+
+void e1000_reset(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 pba = 0, tx_space, min_tx_space, min_rx_space;
+ bool legacy_pba_adjust = false;
+ u16 hwm;
+
+ /* Repartition Pba for greater than 9k mtu
+ * To take effect CTRL.RST is required.
+ */
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ case e1000_82540:
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ legacy_pba_adjust = true;
+ pba = E1000_PBA_48K;
+ break;
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ pba = E1000_PBA_48K;
+ break;
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ legacy_pba_adjust = true;
+ pba = E1000_PBA_30K;
+ break;
+ case e1000_undefined:
+ case e1000_num_macs:
+ break;
+ }
+
+ if (legacy_pba_adjust) {
+ if (hw->max_frame_size > E1000_RXBUFFER_8192)
+ pba -= 8; /* allocate more FIFO for Tx */
+
+ if (hw->mac_type == e1000_82547) {
+ adapter->tx_fifo_head = 0;
+ adapter->tx_head_addr = pba << E1000_TX_HEAD_ADDR_SHIFT;
+ adapter->tx_fifo_size =
+ (E1000_PBA_40K - pba) << E1000_PBA_BYTES_SHIFT;
+ atomic_set(&adapter->tx_fifo_stall, 0);
+ }
+ } else if (hw->max_frame_size > ETH_FRAME_LEN + ETH_FCS_LEN) {
+ /* adjust PBA for jumbo frames */
+ ew32(PBA, pba);
+
+ /* To maintain wire speed transmits, the Tx FIFO should be
+ * large enough to accommodate two full transmit packets,
+ * rounded up to the next 1KB and expressed in KB. Likewise,
+ * the Rx FIFO should be large enough to accommodate at least
+ * one full receive packet and is similarly rounded up and
+ * expressed in KB. */
+ pba = er32(PBA);
+ /* upper 16 bits has Tx packet buffer allocation size in KB */
+ tx_space = pba >> 16;
+ /* lower 16 bits has Rx packet buffer allocation size in KB */
+ pba &= 0xffff;
+ /*
+ * the tx fifo also stores 16 bytes of information about the tx
+ * but don't include ethernet FCS because hardware appends it
+ */
+ min_tx_space = (hw->max_frame_size +
+ sizeof(struct e1000_tx_desc) -
+ ETH_FCS_LEN) * 2;
+ min_tx_space = ALIGN(min_tx_space, 1024);
+ min_tx_space >>= 10;
+ /* software strips receive CRC, so leave room for it */
+ min_rx_space = hw->max_frame_size;
+ min_rx_space = ALIGN(min_rx_space, 1024);
+ min_rx_space >>= 10;
+
+ /* If current Tx allocation is less than the min Tx FIFO size,
+ * and the min Tx FIFO size is less than the current Rx FIFO
+ * allocation, take space away from current Rx allocation */
+ if (tx_space < min_tx_space &&
+ ((min_tx_space - tx_space) < pba)) {
+ pba = pba - (min_tx_space - tx_space);
+
+ /* PCI/PCIx hardware has PBA alignment constraints */
+ switch (hw->mac_type) {
+ case e1000_82545 ... e1000_82546_rev_3:
+ pba &= ~(E1000_PBA_8K - 1);
+ break;
+ default:
+ break;
+ }
+
+ /* if short on rx space, rx wins and must trump tx
+ * adjustment or use Early Receive if available */
+ if (pba < min_rx_space)
+ pba = min_rx_space;
+ }
+ }
+
+ ew32(PBA, pba);
+
+ /*
+ * flow control settings:
+ * The high water mark must be low enough to fit one full frame
+ * (or the size used for early receive) above it in the Rx FIFO.
+ * Set it to the lower of:
+ * - 90% of the Rx FIFO size, and
+ * - the full Rx FIFO size minus the early receive size (for parts
+ * with ERT support assuming ERT set to E1000_ERT_2048), or
+ * - the full Rx FIFO size minus one full frame
+ */
+ hwm = min(((pba << 10) * 9 / 10),
+ ((pba << 10) - hw->max_frame_size));
+
+ hw->fc_high_water = hwm & 0xFFF8; /* 8-byte granularity */
+ hw->fc_low_water = hw->fc_high_water - 8;
+ hw->fc_pause_time = E1000_FC_PAUSE_TIME;
+ hw->fc_send_xon = 1;
+ hw->fc = hw->original_fc;
+
+ /* Allow time for pending master requests to run */
+ e1000_reset_hw(hw);
+ if (hw->mac_type >= e1000_82544)
+ ew32(WUC, 0);
+
+ if (e1000_init_hw(hw))
+ DPRINTK(PROBE, ERR, "Hardware Error\n");
+ e1000_update_mng_vlan(adapter);
+
+ /* if (adapter->hwflags & HWFLAGS_PHY_PWR_BIT) { */
+ if (hw->mac_type >= e1000_82544 &&
+ hw->autoneg == 1 &&
+ hw->autoneg_advertised == ADVERTISE_1000_FULL) {
+ u32 ctrl = er32(CTRL);
+ /* clear phy power management bit if we are in gig only mode,
+ * which if enabled will attempt negotiation to 100Mb, which
+ * can cause a loss of link at power off or driver unload */
+ ctrl &= ~E1000_CTRL_SWDPIN3;
+ ew32(CTRL, ctrl);
+ }
+
+ /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
+ ew32(VET, ETHERNET_IEEE_VLAN_TYPE);
+
+ e1000_reset_adaptive(hw);
+ e1000_phy_get_info(hw, &adapter->phy_info);
+
+ e1000_release_manageability(adapter);
+}
+
+/**
+ * Dump the eeprom for users having checksum issues
+ **/
+static void e1000_dump_eeprom(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct ethtool_eeprom eeprom;
+ const struct ethtool_ops *ops = netdev->ethtool_ops;
+ u8 *data;
+ int i;
+ u16 csum_old, csum_new = 0;
+
+ eeprom.len = ops->get_eeprom_len(netdev);
+ eeprom.offset = 0;
+
+ data = kmalloc(eeprom.len, GFP_KERNEL);
+ if (!data) {
+ printk(KERN_ERR "Unable to allocate memory to dump EEPROM"
+ " data\n");
+ return;
+ }
+
+ ops->get_eeprom(netdev, &eeprom, data);
+
+ csum_old = (data[EEPROM_CHECKSUM_REG * 2]) +
+ (data[EEPROM_CHECKSUM_REG * 2 + 1] << 8);
+ for (i = 0; i < EEPROM_CHECKSUM_REG * 2; i += 2)
+ csum_new += data[i] + (data[i + 1] << 8);
+ csum_new = EEPROM_SUM - csum_new;
+
+ printk(KERN_ERR "/*********************/\n");
+ printk(KERN_ERR "Current EEPROM Checksum : 0x%04x\n", csum_old);
+ printk(KERN_ERR "Calculated : 0x%04x\n", csum_new);
+
+ printk(KERN_ERR "Offset Values\n");
+ printk(KERN_ERR "======== ======\n");
+ print_hex_dump(KERN_ERR, "", DUMP_PREFIX_OFFSET, 16, 1, data, 128, 0);
+
+ printk(KERN_ERR "Include this output when contacting your support "
+ "provider.\n");
+ printk(KERN_ERR "This is not a software error! Something bad "
+ "happened to your hardware or\n");
+ printk(KERN_ERR "EEPROM image. Ignoring this "
+ "problem could result in further problems,\n");
+ printk(KERN_ERR "possibly loss of data, corruption or system hangs!\n");
+ printk(KERN_ERR "The MAC Address will be reset to 00:00:00:00:00:00, "
+ "which is invalid\n");
+ printk(KERN_ERR "and requires you to set the proper MAC "
+ "address manually before continuing\n");
+ printk(KERN_ERR "to enable this network device.\n");
+ printk(KERN_ERR "Please inspect the EEPROM dump and report the issue "
+ "to your hardware vendor\n");
+ printk(KERN_ERR "or Intel Customer Support.\n");
+ printk(KERN_ERR "/*********************/\n");
+
+ kfree(data);
+}
+
+/**
+ * e1000_is_need_ioport - determine if an adapter needs ioport resources or not
+ * @pdev: PCI device information struct
+ *
+ * Return true if an adapter needs ioport resources
+ **/
+static int e1000_is_need_ioport(struct pci_dev *pdev)
+{
+ switch (pdev->device) {
+ case E1000_DEV_ID_82540EM:
+ case E1000_DEV_ID_82540EM_LOM:
+ case E1000_DEV_ID_82540EP:
+ case E1000_DEV_ID_82540EP_LOM:
+ case E1000_DEV_ID_82540EP_LP:
+ case E1000_DEV_ID_82541EI:
+ case E1000_DEV_ID_82541EI_MOBILE:
+ case E1000_DEV_ID_82541ER:
+ case E1000_DEV_ID_82541ER_LOM:
+ case E1000_DEV_ID_82541GI:
+ case E1000_DEV_ID_82541GI_LF:
+ case E1000_DEV_ID_82541GI_MOBILE:
+ case E1000_DEV_ID_82544EI_COPPER:
+ case E1000_DEV_ID_82544EI_FIBER:
+ case E1000_DEV_ID_82544GC_COPPER:
+ case E1000_DEV_ID_82544GC_LOM:
+ case E1000_DEV_ID_82545EM_COPPER:
+ case E1000_DEV_ID_82545EM_FIBER:
+ case E1000_DEV_ID_82546EB_COPPER:
+ case E1000_DEV_ID_82546EB_FIBER:
+ case E1000_DEV_ID_82546EB_QUAD_COPPER:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static const struct net_device_ops e1000_netdev_ops = {
+ .ndo_open = e1000_open,
+ .ndo_stop = e1000_close,
+ .ndo_start_xmit = e1000_xmit_frame,
+ .ndo_get_stats = e1000_get_stats,
+ .ndo_set_rx_mode = e1000_set_rx_mode,
+ .ndo_set_mac_address = e1000_set_mac,
+ .ndo_tx_timeout = e1000_tx_timeout,
+ .ndo_change_mtu = e1000_change_mtu,
+ .ndo_do_ioctl = e1000_ioctl,
+ .ndo_validate_addr = eth_validate_addr,
+
+ .ndo_vlan_rx_register = e1000_vlan_rx_register,
+ .ndo_vlan_rx_add_vid = e1000_vlan_rx_add_vid,
+ .ndo_vlan_rx_kill_vid = e1000_vlan_rx_kill_vid,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = e1000_netpoll,
+#endif
+};
+
+/**
+ * e1000_probe - Device Initialization Routine
+ * @pdev: PCI device information struct
+ * @ent: entry in e1000_pci_tbl
+ *
+ * Returns 0 on success, negative on failure
+ *
+ * e1000_probe initializes an adapter identified by a pci_dev structure.
+ * The OS initialization, configuring of the adapter private structure,
+ * and a hardware reset occur.
+ **/
+static int __devinit e1000_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct net_device *netdev;
+ struct e1000_adapter *adapter;
+ struct e1000_hw *hw;
+
+ static int cards_found = 0;
+ static int global_quad_port_a = 0; /* global ksp3 port a indication */
+ int i, err, pci_using_dac;
+ u16 eeprom_data = 0;
+ u16 eeprom_apme_mask = E1000_EEPROM_APME;
+ int bars, need_ioport;
+
+ /* do not allocate ioport bars when not needed */
+ need_ioport = e1000_is_need_ioport(pdev);
+ if (need_ioport) {
+ bars = pci_select_bars(pdev, IORESOURCE_MEM | IORESOURCE_IO);
+ err = pci_enable_device(pdev);
+ } else {
+ bars = pci_select_bars(pdev, IORESOURCE_MEM);
+ err = pci_enable_device_mem(pdev);
+ }
+ if (err)
+ return err;
+
+ if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64)) &&
+ !pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64))) {
+ pci_using_dac = 1;
+ } else {
+ err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (err) {
+ err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (err) {
+ E1000_ERR("No usable DMA configuration, "
+ "aborting\n");
+ goto err_dma;
+ }
+ }
+ pci_using_dac = 0;
+ }
+
+ err = pci_request_selected_regions(pdev, bars, e1000_driver_name);
+ if (err)
+ goto err_pci_reg;
+
+ pci_set_master(pdev);
+
+ err = -ENOMEM;
+ netdev = alloc_etherdev(sizeof(struct e1000_adapter));
+ if (!netdev)
+ goto err_alloc_etherdev;
+
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+
+ pci_set_drvdata(pdev, netdev);
+ adapter = netdev_priv(netdev);
+ adapter->netdev = netdev;
+ adapter->pdev = pdev;
+ adapter->msg_enable = (1 << debug) - 1;
+ adapter->bars = bars;
+ adapter->need_ioport = need_ioport;
+
+ hw = &adapter->hw;
+ hw->back = adapter;
+
+ err = -EIO;
+ hw->hw_addr = pci_ioremap_bar(pdev, BAR_0);
+ if (!hw->hw_addr)
+ goto err_ioremap;
+
+ if (adapter->need_ioport) {
+ for (i = BAR_1; i <= BAR_5; i++) {
+ if (pci_resource_len(pdev, i) == 0)
+ continue;
+ if (pci_resource_flags(pdev, i) & IORESOURCE_IO) {
+ hw->io_base = pci_resource_start(pdev, i);
+ break;
+ }
+ }
+ }
+
+ netdev->netdev_ops = &e1000_netdev_ops;
+ e1000_set_ethtool_ops(netdev);
+ netdev->watchdog_timeo = 5 * HZ;
+ netif_napi_add(netdev, &adapter->napi, e1000_clean, 64);
+
+ strncpy(netdev->name, pci_name(pdev), sizeof(netdev->name) - 1);
+
+ adapter->bd_number = cards_found;
+
+ /* setup the private structure */
+
+ err = e1000_sw_init(adapter);
+ if (err)
+ goto err_sw_init;
+
+ err = -EIO;
+
+ if (hw->mac_type >= e1000_82543) {
+ netdev->features = NETIF_F_SG |
+ NETIF_F_HW_CSUM |
+ NETIF_F_HW_VLAN_TX |
+ NETIF_F_HW_VLAN_RX |
+ NETIF_F_HW_VLAN_FILTER;
+ }
+
+ if ((hw->mac_type >= e1000_82544) &&
+ (hw->mac_type != e1000_82547))
+ netdev->features |= NETIF_F_TSO;
+
+ if (pci_using_dac)
+ netdev->features |= NETIF_F_HIGHDMA;
+
+ netdev->vlan_features |= NETIF_F_TSO;
+ netdev->vlan_features |= NETIF_F_HW_CSUM;
+ netdev->vlan_features |= NETIF_F_SG;
+
+ adapter->en_mng_pt = e1000_enable_mng_pass_thru(hw);
+
+ /* initialize eeprom parameters */
+ if (e1000_init_eeprom_params(hw)) {
+ E1000_ERR("EEPROM initialization failed\n");
+ goto err_eeprom;
+ }
+
+ /* before reading the EEPROM, reset the controller to
+ * put the device in a known good starting state */
+
+ e1000_reset_hw(hw);
+
+ /* make sure the EEPROM is good */
+ if (e1000_validate_eeprom_checksum(hw) < 0) {
+ DPRINTK(PROBE, ERR, "The EEPROM Checksum Is Not Valid\n");
+ e1000_dump_eeprom(adapter);
+ /*
+ * set MAC address to all zeroes to invalidate and temporary
+ * disable this device for the user. This blocks regular
+ * traffic while still permitting ethtool ioctls from reaching
+ * the hardware as well as allowing the user to run the
+ * interface after manually setting a hw addr using
+ * `ip set address`
+ */
+ memset(hw->mac_addr, 0, netdev->addr_len);
+ } else {
+ /* copy the MAC address out of the EEPROM */
+ if (e1000_read_mac_addr(hw))
+ DPRINTK(PROBE, ERR, "EEPROM Read Error\n");
+ }
+ /* don't block initalization here due to bad MAC address */
+ memcpy(netdev->dev_addr, hw->mac_addr, netdev->addr_len);
+ memcpy(netdev->perm_addr, hw->mac_addr, netdev->addr_len);
+
+ if (!is_valid_ether_addr(netdev->perm_addr))
+ DPRINTK(PROBE, ERR, "Invalid MAC Address\n");
+
+ e1000_get_bus_info(hw);
+
+ init_timer(&adapter->tx_fifo_stall_timer);
+ adapter->tx_fifo_stall_timer.function = &e1000_82547_tx_fifo_stall;
+ adapter->tx_fifo_stall_timer.data = (unsigned long)adapter;
+
+ init_timer(&adapter->watchdog_timer);
+ adapter->watchdog_timer.function = &e1000_watchdog;
+ adapter->watchdog_timer.data = (unsigned long) adapter;
+
+ init_timer(&adapter->phy_info_timer);
+ adapter->phy_info_timer.function = &e1000_update_phy_info;
+ adapter->phy_info_timer.data = (unsigned long)adapter;
+
+ INIT_WORK(&adapter->reset_task, e1000_reset_task);
+
+ e1000_check_options(adapter);
+
+ /* Initial Wake on LAN setting
+ * If APM wake is enabled in the EEPROM,
+ * enable the ACPI Magic Packet filter
+ */
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ break;
+ case e1000_82544:
+ e1000_read_eeprom(hw,
+ EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
+ eeprom_apme_mask = E1000_EEPROM_82544_APM;
+ break;
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ if (er32(STATUS) & E1000_STATUS_FUNC_1){
+ e1000_read_eeprom(hw,
+ EEPROM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
+ break;
+ }
+ /* Fall Through */
+ default:
+ e1000_read_eeprom(hw,
+ EEPROM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
+ break;
+ }
+ if (eeprom_data & eeprom_apme_mask)
+ adapter->eeprom_wol |= E1000_WUFC_MAG;
+
+ /* now that we have the eeprom settings, apply the special cases
+ * where the eeprom may be wrong or the board simply won't support
+ * wake on lan on a particular port */
+ switch (pdev->device) {
+ case E1000_DEV_ID_82546GB_PCIE:
+ adapter->eeprom_wol = 0;
+ break;
+ case E1000_DEV_ID_82546EB_FIBER:
+ case E1000_DEV_ID_82546GB_FIBER:
+ /* Wake events only supported on port A for dual fiber
+ * regardless of eeprom setting */
+ if (er32(STATUS) & E1000_STATUS_FUNC_1)
+ adapter->eeprom_wol = 0;
+ break;
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ /* if quad port adapter, disable WoL on all but port A */
+ if (global_quad_port_a != 0)
+ adapter->eeprom_wol = 0;
+ else
+ adapter->quad_port_a = 1;
+ /* Reset for multiple quad port adapters */
+ if (++global_quad_port_a == 4)
+ global_quad_port_a = 0;
+ break;
+ }
+
+ /* initialize the wol settings based on the eeprom settings */
+ adapter->wol = adapter->eeprom_wol;
+ device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
+
+ /* print bus type/speed/width info */
+ DPRINTK(PROBE, INFO, "(PCI%s:%s:%s) ",
+ ((hw->bus_type == e1000_bus_type_pcix) ? "-X" : ""),
+ ((hw->bus_speed == e1000_bus_speed_133) ? "133MHz" :
+ (hw->bus_speed == e1000_bus_speed_120) ? "120MHz" :
+ (hw->bus_speed == e1000_bus_speed_100) ? "100MHz" :
+ (hw->bus_speed == e1000_bus_speed_66) ? "66MHz" : "33MHz"),
+ ((hw->bus_width == e1000_bus_width_64) ? "64-bit" : "32-bit"));
+
+ printk("%pM\n", netdev->dev_addr);
+
+ /* reset the hardware with the new settings */
+ e1000_reset(adapter);
+
+ strcpy(netdev->name, "eth%d");
+ err = register_netdev(netdev);
+ if (err)
+ goto err_register;
+
+ /* carrier off reporting is important to ethtool even BEFORE open */
+ netif_carrier_off(netdev);
+
+ DPRINTK(PROBE, INFO, "Intel(R) PRO/1000 Network Connection\n");
+
+ cards_found++;
+ return 0;
+
+err_register:
+err_eeprom:
+ e1000_phy_hw_reset(hw);
+
+ if (hw->flash_address)
+ iounmap(hw->flash_address);
+ kfree(adapter->tx_ring);
+ kfree(adapter->rx_ring);
+err_sw_init:
+ iounmap(hw->hw_addr);
+err_ioremap:
+ free_netdev(netdev);
+err_alloc_etherdev:
+ pci_release_selected_regions(pdev, bars);
+err_pci_reg:
+err_dma:
+ pci_disable_device(pdev);
+ return err;
+}
+
+/**
+ * e1000_remove - Device Removal Routine
+ * @pdev: PCI device information struct
+ *
+ * e1000_remove is called by the PCI subsystem to alert the driver
+ * that it should release a PCI device. The could be caused by a
+ * Hot-Plug event, or because the driver is going to be removed from
+ * memory.
+ **/
+
+static void __devexit e1000_remove(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ set_bit(__E1000_DOWN, &adapter->flags);
+ del_timer_sync(&adapter->tx_fifo_stall_timer);
+ del_timer_sync(&adapter->watchdog_timer);
+ del_timer_sync(&adapter->phy_info_timer);
+
+ cancel_work_sync(&adapter->reset_task);
+
+ e1000_release_manageability(adapter);
+
+ unregister_netdev(netdev);
+
+ e1000_phy_hw_reset(hw);
+
+ kfree(adapter->tx_ring);
+ kfree(adapter->rx_ring);
+
+ iounmap(hw->hw_addr);
+ if (hw->flash_address)
+ iounmap(hw->flash_address);
+ pci_release_selected_regions(pdev, adapter->bars);
+
+ free_netdev(netdev);
+
+ pci_disable_device(pdev);
+}
+
+/**
+ * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
+ * @adapter: board private structure to initialize
+ *
+ * e1000_sw_init initializes the Adapter private data structure.
+ * Fields are initialized based on PCI device information and
+ * OS network device settings (MTU size).
+ **/
+
+static int __devinit e1000_sw_init(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+
+ /* PCI config space info */
+
+ hw->vendor_id = pdev->vendor;
+ hw->device_id = pdev->device;
+ hw->subsystem_vendor_id = pdev->subsystem_vendor;
+ hw->subsystem_id = pdev->subsystem_device;
+ hw->revision_id = pdev->revision;
+
+ pci_read_config_word(pdev, PCI_COMMAND, &hw->pci_cmd_word);
+
+ adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
+ hw->max_frame_size = netdev->mtu +
+ ENET_HEADER_SIZE + ETHERNET_FCS_SIZE;
+ hw->min_frame_size = MINIMUM_ETHERNET_FRAME_SIZE;
+
+ /* identify the MAC */
+
+ if (e1000_set_mac_type(hw)) {
+ DPRINTK(PROBE, ERR, "Unknown MAC Type\n");
+ return -EIO;
+ }
+
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ hw->phy_init_script = 1;
+ break;
+ }
+
+ e1000_set_media_type(hw);
+
+ hw->wait_autoneg_complete = false;
+ hw->tbi_compatibility_en = true;
+ hw->adaptive_ifs = true;
+
+ /* Copper options */
+
+ if (hw->media_type == e1000_media_type_copper) {
+ hw->mdix = AUTO_ALL_MODES;
+ hw->disable_polarity_correction = false;
+ hw->master_slave = E1000_MASTER_SLAVE;
+ }
+
+ adapter->num_tx_queues = 1;
+ adapter->num_rx_queues = 1;
+
+ if (e1000_alloc_queues(adapter)) {
+ DPRINTK(PROBE, ERR, "Unable to allocate memory for queues\n");
+ return -ENOMEM;
+ }
+
+ /* Explicitly disable IRQ since the NIC can be in any state. */
+ e1000_irq_disable(adapter);
+
+ spin_lock_init(&adapter->stats_lock);
+
+ set_bit(__E1000_DOWN, &adapter->flags);
+
+ return 0;
+}
+
+/**
+ * e1000_alloc_queues - Allocate memory for all rings
+ * @adapter: board private structure to initialize
+ *
+ * We allocate one ring per queue at run-time since we don't know the
+ * number of queues at compile-time.
+ **/
+
+static int __devinit e1000_alloc_queues(struct e1000_adapter *adapter)
+{
+ adapter->tx_ring = kcalloc(adapter->num_tx_queues,
+ sizeof(struct e1000_tx_ring), GFP_KERNEL);
+ if (!adapter->tx_ring)
+ return -ENOMEM;
+
+ adapter->rx_ring = kcalloc(adapter->num_rx_queues,
+ sizeof(struct e1000_rx_ring), GFP_KERNEL);
+ if (!adapter->rx_ring) {
+ kfree(adapter->tx_ring);
+ return -ENOMEM;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_open - Called when a network interface is made active
+ * @netdev: network interface device structure
+ *
+ * Returns 0 on success, negative value on failure
+ *
+ * The open entry point is called when a network interface is made
+ * active by the system (IFF_UP). At this point all resources needed
+ * for transmit and receive operations are allocated, the interrupt
+ * handler is registered with the OS, the watchdog timer is started,
+ * and the stack is notified that the interface is ready.
+ **/
+
+static int e1000_open(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ int err;
+
+ /* disallow open during test */
+ if (test_bit(__E1000_TESTING, &adapter->flags))
+ return -EBUSY;
+
+ netif_carrier_off(netdev);
+
+ /* allocate transmit descriptors */
+ err = e1000_setup_all_tx_resources(adapter);
+ if (err)
+ goto err_setup_tx;
+
+ /* allocate receive descriptors */
+ err = e1000_setup_all_rx_resources(adapter);
+ if (err)
+ goto err_setup_rx;
+
+ e1000_power_up_phy(adapter);
+
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+ if ((hw->mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT)) {
+ e1000_update_mng_vlan(adapter);
+ }
+
+ /* before we allocate an interrupt, we must be ready to handle it.
+ * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
+ * as soon as we call pci_request_irq, so we have to setup our
+ * clean_rx handler before we do so. */
+ e1000_configure(adapter);
+
+ err = e1000_request_irq(adapter);
+ if (err)
+ goto err_req_irq;
+
+ /* From here on the code is the same as e1000_up() */
+ clear_bit(__E1000_DOWN, &adapter->flags);
+
+ napi_enable(&adapter->napi);
+
+ e1000_irq_enable(adapter);
+
+ netif_start_queue(netdev);
+
+ /* fire a link status change interrupt to start the watchdog */
+ ew32(ICS, E1000_ICS_LSC);
+
+ return E1000_SUCCESS;
+
+err_req_irq:
+ e1000_power_down_phy(adapter);
+ e1000_free_all_rx_resources(adapter);
+err_setup_rx:
+ e1000_free_all_tx_resources(adapter);
+err_setup_tx:
+ e1000_reset(adapter);
+
+ return err;
+}
+
+/**
+ * e1000_close - Disables a network interface
+ * @netdev: network interface device structure
+ *
+ * Returns 0, this is not allowed to fail
+ *
+ * The close entry point is called when an interface is de-activated
+ * by the OS. The hardware is still under the drivers control, but
+ * needs to be disabled. A global MAC reset is issued to stop the
+ * hardware, and all transmit and receive resources are freed.
+ **/
+
+static int e1000_close(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
+ e1000_down(adapter);
+ e1000_power_down_phy(adapter);
+ e1000_free_irq(adapter);
+
+ e1000_free_all_tx_resources(adapter);
+ e1000_free_all_rx_resources(adapter);
+
+ /* kill manageability vlan ID if supported, but not if a vlan with
+ * the same ID is registered on the host OS (let 8021q kill it) */
+ if ((hw->mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
+ !(adapter->vlgrp &&
+ vlan_group_get_device(adapter->vlgrp, adapter->mng_vlan_id))) {
+ e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_check_64k_bound - check that memory doesn't cross 64kB boundary
+ * @adapter: address of board private structure
+ * @start: address of beginning of memory
+ * @len: length of memory
+ **/
+static bool e1000_check_64k_bound(struct e1000_adapter *adapter, void *start,
+ unsigned long len)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ unsigned long begin = (unsigned long)start;
+ unsigned long end = begin + len;
+
+ /* First rev 82545 and 82546 need to not allow any memory
+ * write location to cross 64k boundary due to errata 23 */
+ if (hw->mac_type == e1000_82545 ||
+ hw->mac_type == e1000_82546) {
+ return ((begin ^ (end - 1)) >> 16) != 0 ? false : true;
+ }
+
+ return true;
+}
+
+/**
+ * e1000_setup_tx_resources - allocate Tx resources (Descriptors)
+ * @adapter: board private structure
+ * @txdr: tx descriptor ring (for a specific queue) to setup
+ *
+ * Return 0 on success, negative on failure
+ **/
+
+static int e1000_setup_tx_resources(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *txdr)
+{
+ struct pci_dev *pdev = adapter->pdev;
+ int size;
+
+ size = sizeof(struct e1000_buffer) * txdr->count;
+ txdr->buffer_info = vmalloc(size);
+ if (!txdr->buffer_info) {
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate memory for the transmit descriptor ring\n");
+ return -ENOMEM;
+ }
+ memset(txdr->buffer_info, 0, size);
+
+ /* round up to nearest 4K */
+
+ txdr->size = txdr->count * sizeof(struct e1000_tx_desc);
+ txdr->size = ALIGN(txdr->size, 4096);
+
+ txdr->desc = pci_alloc_consistent(pdev, txdr->size, &txdr->dma);
+ if (!txdr->desc) {
+setup_tx_desc_die:
+ vfree(txdr->buffer_info);
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate memory for the transmit descriptor ring\n");
+ return -ENOMEM;
+ }
+
+ /* Fix for errata 23, can't cross 64kB boundary */
+ if (!e1000_check_64k_bound(adapter, txdr->desc, txdr->size)) {
+ void *olddesc = txdr->desc;
+ dma_addr_t olddma = txdr->dma;
+ DPRINTK(TX_ERR, ERR, "txdr align check failed: %u bytes "
+ "at %p\n", txdr->size, txdr->desc);
+ /* Try again, without freeing the previous */
+ txdr->desc = pci_alloc_consistent(pdev, txdr->size, &txdr->dma);
+ /* Failed allocation, critical failure */
+ if (!txdr->desc) {
+ pci_free_consistent(pdev, txdr->size, olddesc, olddma);
+ goto setup_tx_desc_die;
+ }
+
+ if (!e1000_check_64k_bound(adapter, txdr->desc, txdr->size)) {
+ /* give up */
+ pci_free_consistent(pdev, txdr->size, txdr->desc,
+ txdr->dma);
+ pci_free_consistent(pdev, txdr->size, olddesc, olddma);
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate aligned memory "
+ "for the transmit descriptor ring\n");
+ vfree(txdr->buffer_info);
+ return -ENOMEM;
+ } else {
+ /* Free old allocation, new allocation was successful */
+ pci_free_consistent(pdev, txdr->size, olddesc, olddma);
+ }
+ }
+ memset(txdr->desc, 0, txdr->size);
+
+ txdr->next_to_use = 0;
+ txdr->next_to_clean = 0;
+
+ return 0;
+}
+
+/**
+ * e1000_setup_all_tx_resources - wrapper to allocate Tx resources
+ * (Descriptors) for all queues
+ * @adapter: board private structure
+ *
+ * Return 0 on success, negative on failure
+ **/
+
+int e1000_setup_all_tx_resources(struct e1000_adapter *adapter)
+{
+ int i, err = 0;
+
+ for (i = 0; i < adapter->num_tx_queues; i++) {
+ err = e1000_setup_tx_resources(adapter, &adapter->tx_ring[i]);
+ if (err) {
+ DPRINTK(PROBE, ERR,
+ "Allocation for Tx Queue %u failed\n", i);
+ for (i-- ; i >= 0; i--)
+ e1000_free_tx_resources(adapter,
+ &adapter->tx_ring[i]);
+ break;
+ }
+ }
+
+ return err;
+}
+
+/**
+ * e1000_configure_tx - Configure 8254x Transmit Unit after Reset
+ * @adapter: board private structure
+ *
+ * Configure the Tx unit of the MAC after a reset.
+ **/
+
+static void e1000_configure_tx(struct e1000_adapter *adapter)
+{
+ u64 tdba;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 tdlen, tctl, tipg;
+ u32 ipgr1, ipgr2;
+
+ /* Setup the HW Tx Head and Tail descriptor pointers */
+
+ switch (adapter->num_tx_queues) {
+ case 1:
+ default:
+ tdba = adapter->tx_ring[0].dma;
+ tdlen = adapter->tx_ring[0].count *
+ sizeof(struct e1000_tx_desc);
+ ew32(TDLEN, tdlen);
+ ew32(TDBAH, (tdba >> 32));
+ ew32(TDBAL, (tdba & 0x00000000ffffffffULL));
+ ew32(TDT, 0);
+ ew32(TDH, 0);
+ adapter->tx_ring[0].tdh = ((hw->mac_type >= e1000_82543) ? E1000_TDH : E1000_82542_TDH);
+ adapter->tx_ring[0].tdt = ((hw->mac_type >= e1000_82543) ? E1000_TDT : E1000_82542_TDT);
+ break;
+ }
+
+ /* Set the default values for the Tx Inter Packet Gap timer */
+ if ((hw->media_type == e1000_media_type_fiber ||
+ hw->media_type == e1000_media_type_internal_serdes))
+ tipg = DEFAULT_82543_TIPG_IPGT_FIBER;
+ else
+ tipg = DEFAULT_82543_TIPG_IPGT_COPPER;
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ tipg = DEFAULT_82542_TIPG_IPGT;
+ ipgr1 = DEFAULT_82542_TIPG_IPGR1;
+ ipgr2 = DEFAULT_82542_TIPG_IPGR2;
+ break;
+ default:
+ ipgr1 = DEFAULT_82543_TIPG_IPGR1;
+ ipgr2 = DEFAULT_82543_TIPG_IPGR2;
+ break;
+ }
+ tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT;
+ tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT;
+ ew32(TIPG, tipg);
+
+ /* Set the Tx Interrupt Delay register */
+
+ ew32(TIDV, adapter->tx_int_delay);
+ if (hw->mac_type >= e1000_82540)
+ ew32(TADV, adapter->tx_abs_int_delay);
+
+ /* Program the Transmit Control Register */
+
+ tctl = er32(TCTL);
+ tctl &= ~E1000_TCTL_CT;
+ tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC |
+ (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
+
+ e1000_config_collision_dist(hw);
+
+ /* Setup Transmit Descriptor Settings for eop descriptor */
+ adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
+
+ /* only set IDE if we are delaying interrupts using the timers */
+ if (adapter->tx_int_delay)
+ adapter->txd_cmd |= E1000_TXD_CMD_IDE;
+
+ if (hw->mac_type < e1000_82543)
+ adapter->txd_cmd |= E1000_TXD_CMD_RPS;
+ else
+ adapter->txd_cmd |= E1000_TXD_CMD_RS;
+
+ /* Cache if we're 82544 running in PCI-X because we'll
+ * need this to apply a workaround later in the send path. */
+ if (hw->mac_type == e1000_82544 &&
+ hw->bus_type == e1000_bus_type_pcix)
+ adapter->pcix_82544 = 1;
+
+ ew32(TCTL, tctl);
+
+}
+
+/**
+ * e1000_setup_rx_resources - allocate Rx resources (Descriptors)
+ * @adapter: board private structure
+ * @rxdr: rx descriptor ring (for a specific queue) to setup
+ *
+ * Returns 0 on success, negative on failure
+ **/
+
+static int e1000_setup_rx_resources(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rxdr)
+{
+ struct pci_dev *pdev = adapter->pdev;
+ int size, desc_len;
+
+ size = sizeof(struct e1000_buffer) * rxdr->count;
+ rxdr->buffer_info = vmalloc(size);
+ if (!rxdr->buffer_info) {
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate memory for the receive descriptor ring\n");
+ return -ENOMEM;
+ }
+ memset(rxdr->buffer_info, 0, size);
+
+ desc_len = sizeof(struct e1000_rx_desc);
+
+ /* Round up to nearest 4K */
+
+ rxdr->size = rxdr->count * desc_len;
+ rxdr->size = ALIGN(rxdr->size, 4096);
+
+ rxdr->desc = pci_alloc_consistent(pdev, rxdr->size, &rxdr->dma);
+
+ if (!rxdr->desc) {
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate memory for the receive descriptor ring\n");
+setup_rx_desc_die:
+ vfree(rxdr->buffer_info);
+ return -ENOMEM;
+ }
+
+ /* Fix for errata 23, can't cross 64kB boundary */
+ if (!e1000_check_64k_bound(adapter, rxdr->desc, rxdr->size)) {
+ void *olddesc = rxdr->desc;
+ dma_addr_t olddma = rxdr->dma;
+ DPRINTK(RX_ERR, ERR, "rxdr align check failed: %u bytes "
+ "at %p\n", rxdr->size, rxdr->desc);
+ /* Try again, without freeing the previous */
+ rxdr->desc = pci_alloc_consistent(pdev, rxdr->size, &rxdr->dma);
+ /* Failed allocation, critical failure */
+ if (!rxdr->desc) {
+ pci_free_consistent(pdev, rxdr->size, olddesc, olddma);
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate memory "
+ "for the receive descriptor ring\n");
+ goto setup_rx_desc_die;
+ }
+
+ if (!e1000_check_64k_bound(adapter, rxdr->desc, rxdr->size)) {
+ /* give up */
+ pci_free_consistent(pdev, rxdr->size, rxdr->desc,
+ rxdr->dma);
+ pci_free_consistent(pdev, rxdr->size, olddesc, olddma);
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate aligned memory "
+ "for the receive descriptor ring\n");
+ goto setup_rx_desc_die;
+ } else {
+ /* Free old allocation, new allocation was successful */
+ pci_free_consistent(pdev, rxdr->size, olddesc, olddma);
+ }
+ }
+ memset(rxdr->desc, 0, rxdr->size);
+
+ rxdr->next_to_clean = 0;
+ rxdr->next_to_use = 0;
+ rxdr->rx_skb_top = NULL;
+
+ return 0;
+}
+
+/**
+ * e1000_setup_all_rx_resources - wrapper to allocate Rx resources
+ * (Descriptors) for all queues
+ * @adapter: board private structure
+ *
+ * Return 0 on success, negative on failure
+ **/
+
+int e1000_setup_all_rx_resources(struct e1000_adapter *adapter)
+{
+ int i, err = 0;
+
+ for (i = 0; i < adapter->num_rx_queues; i++) {
+ err = e1000_setup_rx_resources(adapter, &adapter->rx_ring[i]);
+ if (err) {
+ DPRINTK(PROBE, ERR,
+ "Allocation for Rx Queue %u failed\n", i);
+ for (i-- ; i >= 0; i--)
+ e1000_free_rx_resources(adapter,
+ &adapter->rx_ring[i]);
+ break;
+ }
+ }
+
+ return err;
+}
+
+/**
+ * e1000_setup_rctl - configure the receive control registers
+ * @adapter: Board private structure
+ **/
+static void e1000_setup_rctl(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl;
+
+ rctl = er32(RCTL);
+
+ rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
+
+ rctl |= E1000_RCTL_EN | E1000_RCTL_BAM |
+ E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
+ (hw->mc_filter_type << E1000_RCTL_MO_SHIFT);
+
+ if (hw->tbi_compatibility_on == 1)
+ rctl |= E1000_RCTL_SBP;
+ else
+ rctl &= ~E1000_RCTL_SBP;
+
+ if (adapter->netdev->mtu <= ETH_DATA_LEN)
+ rctl &= ~E1000_RCTL_LPE;
+ else
+ rctl |= E1000_RCTL_LPE;
+
+ /* Setup buffer sizes */
+ rctl &= ~E1000_RCTL_SZ_4096;
+ rctl |= E1000_RCTL_BSEX;
+ switch (adapter->rx_buffer_len) {
+ case E1000_RXBUFFER_2048:
+ default:
+ rctl |= E1000_RCTL_SZ_2048;
+ rctl &= ~E1000_RCTL_BSEX;
+ break;
+ case E1000_RXBUFFER_4096:
+ rctl |= E1000_RCTL_SZ_4096;
+ break;
+ case E1000_RXBUFFER_8192:
+ rctl |= E1000_RCTL_SZ_8192;
+ break;
+ case E1000_RXBUFFER_16384:
+ rctl |= E1000_RCTL_SZ_16384;
+ break;
+ }
+
+ ew32(RCTL, rctl);
+}
+
+/**
+ * e1000_configure_rx - Configure 8254x Receive Unit after Reset
+ * @adapter: board private structure
+ *
+ * Configure the Rx unit of the MAC after a reset.
+ **/
+
+static void e1000_configure_rx(struct e1000_adapter *adapter)
+{
+ u64 rdba;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rdlen, rctl, rxcsum;
+
+ if (adapter->netdev->mtu > ETH_DATA_LEN) {
+ rdlen = adapter->rx_ring[0].count *
+ sizeof(struct e1000_rx_desc);
+ adapter->clean_rx = e1000_clean_jumbo_rx_irq;
+ adapter->alloc_rx_buf = e1000_alloc_jumbo_rx_buffers;
+ } else {
+ rdlen = adapter->rx_ring[0].count *
+ sizeof(struct e1000_rx_desc);
+ adapter->clean_rx = e1000_clean_rx_irq;
+ adapter->alloc_rx_buf = e1000_alloc_rx_buffers;
+ }
+
+ /* disable receives while setting up the descriptors */
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+
+ /* set the Receive Delay Timer Register */
+ ew32(RDTR, adapter->rx_int_delay);
+
+ if (hw->mac_type >= e1000_82540) {
+ ew32(RADV, adapter->rx_abs_int_delay);
+ if (adapter->itr_setting != 0)
+ ew32(ITR, 1000000000 / (adapter->itr * 256));
+ }
+
+ /* Setup the HW Rx Head and Tail Descriptor Pointers and
+ * the Base and Length of the Rx Descriptor Ring */
+ switch (adapter->num_rx_queues) {
+ case 1:
+ default:
+ rdba = adapter->rx_ring[0].dma;
+ ew32(RDLEN, rdlen);
+ ew32(RDBAH, (rdba >> 32));
+ ew32(RDBAL, (rdba & 0x00000000ffffffffULL));
+ ew32(RDT, 0);
+ ew32(RDH, 0);
+ adapter->rx_ring[0].rdh = ((hw->mac_type >= e1000_82543) ? E1000_RDH : E1000_82542_RDH);
+ adapter->rx_ring[0].rdt = ((hw->mac_type >= e1000_82543) ? E1000_RDT : E1000_82542_RDT);
+ break;
+ }
+
+ /* Enable 82543 Receive Checksum Offload for TCP and UDP */
+ if (hw->mac_type >= e1000_82543) {
+ rxcsum = er32(RXCSUM);
+ if (adapter->rx_csum)
+ rxcsum |= E1000_RXCSUM_TUOFL;
+ else
+ /* don't need to clear IPPCSE as it defaults to 0 */
+ rxcsum &= ~E1000_RXCSUM_TUOFL;
+ ew32(RXCSUM, rxcsum);
+ }
+
+ /* Enable Receives */
+ ew32(RCTL, rctl);
+}
+
+/**
+ * e1000_free_tx_resources - Free Tx Resources per Queue
+ * @adapter: board private structure
+ * @tx_ring: Tx descriptor ring for a specific queue
+ *
+ * Free all transmit software resources
+ **/
+
+static void e1000_free_tx_resources(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring)
+{
+ struct pci_dev *pdev = adapter->pdev;
+
+ e1000_clean_tx_ring(adapter, tx_ring);
+
+ vfree(tx_ring->buffer_info);
+ tx_ring->buffer_info = NULL;
+
+ pci_free_consistent(pdev, tx_ring->size, tx_ring->desc, tx_ring->dma);
+
+ tx_ring->desc = NULL;
+}
+
+/**
+ * e1000_free_all_tx_resources - Free Tx Resources for All Queues
+ * @adapter: board private structure
+ *
+ * Free all transmit software resources
+ **/
+
+void e1000_free_all_tx_resources(struct e1000_adapter *adapter)
+{
+ int i;
+
+ for (i = 0; i < adapter->num_tx_queues; i++)
+ e1000_free_tx_resources(adapter, &adapter->tx_ring[i]);
+}
+
+static void e1000_unmap_and_free_tx_resource(struct e1000_adapter *adapter,
+ struct e1000_buffer *buffer_info)
+{
+ buffer_info->dma = 0;
+ if (buffer_info->skb) {
+ skb_dma_unmap(&adapter->pdev->dev, buffer_info->skb,
+ DMA_TO_DEVICE);
+ dev_kfree_skb_any(buffer_info->skb);
+ buffer_info->skb = NULL;
+ }
+ buffer_info->time_stamp = 0;
+ /* buffer_info must be completely set up in the transmit path */
+}
+
+/**
+ * e1000_clean_tx_ring - Free Tx Buffers
+ * @adapter: board private structure
+ * @tx_ring: ring to be cleaned
+ **/
+
+static void e1000_clean_tx_ring(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_buffer *buffer_info;
+ unsigned long size;
+ unsigned int i;
+
+ /* Free all the Tx ring sk_buffs */
+
+ for (i = 0; i < tx_ring->count; i++) {
+ buffer_info = &tx_ring->buffer_info[i];
+ e1000_unmap_and_free_tx_resource(adapter, buffer_info);
+ }
+
+ size = sizeof(struct e1000_buffer) * tx_ring->count;
+ memset(tx_ring->buffer_info, 0, size);
+
+ /* Zero out the descriptor ring */
+
+ memset(tx_ring->desc, 0, tx_ring->size);
+
+ tx_ring->next_to_use = 0;
+ tx_ring->next_to_clean = 0;
+ tx_ring->last_tx_tso = 0;
+
+ writel(0, hw->hw_addr + tx_ring->tdh);
+ writel(0, hw->hw_addr + tx_ring->tdt);
+}
+
+/**
+ * e1000_clean_all_tx_rings - Free Tx Buffers for all queues
+ * @adapter: board private structure
+ **/
+
+static void e1000_clean_all_tx_rings(struct e1000_adapter *adapter)
+{
+ int i;
+
+ for (i = 0; i < adapter->num_tx_queues; i++)
+ e1000_clean_tx_ring(adapter, &adapter->tx_ring[i]);
+}
+
+/**
+ * e1000_free_rx_resources - Free Rx Resources
+ * @adapter: board private structure
+ * @rx_ring: ring to clean the resources from
+ *
+ * Free all receive software resources
+ **/
+
+static void e1000_free_rx_resources(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring)
+{
+ struct pci_dev *pdev = adapter->pdev;
+
+ e1000_clean_rx_ring(adapter, rx_ring);
+
+ vfree(rx_ring->buffer_info);
+ rx_ring->buffer_info = NULL;
+
+ pci_free_consistent(pdev, rx_ring->size, rx_ring->desc, rx_ring->dma);
+
+ rx_ring->desc = NULL;
+}
+
+/**
+ * e1000_free_all_rx_resources - Free Rx Resources for All Queues
+ * @adapter: board private structure
+ *
+ * Free all receive software resources
+ **/
+
+void e1000_free_all_rx_resources(struct e1000_adapter *adapter)
+{
+ int i;
+
+ for (i = 0; i < adapter->num_rx_queues; i++)
+ e1000_free_rx_resources(adapter, &adapter->rx_ring[i]);
+}
+
+/**
+ * e1000_clean_rx_ring - Free Rx Buffers per Queue
+ * @adapter: board private structure
+ * @rx_ring: ring to free buffers from
+ **/
+
+static void e1000_clean_rx_ring(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_buffer *buffer_info;
+ struct pci_dev *pdev = adapter->pdev;
+ unsigned long size;
+ unsigned int i;
+
+ /* Free all the Rx ring sk_buffs */
+ for (i = 0; i < rx_ring->count; i++) {
+ buffer_info = &rx_ring->buffer_info[i];
+ if (buffer_info->dma &&
+ adapter->clean_rx == e1000_clean_rx_irq) {
+ pci_unmap_single(pdev, buffer_info->dma,
+ buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+ } else if (buffer_info->dma &&
+ adapter->clean_rx == e1000_clean_jumbo_rx_irq) {
+ pci_unmap_page(pdev, buffer_info->dma,
+ buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+ }
+
+ buffer_info->dma = 0;
+ if (buffer_info->page) {
+ put_page(buffer_info->page);
+ buffer_info->page = NULL;
+ }
+ if (buffer_info->skb) {
+ dev_kfree_skb(buffer_info->skb);
+ buffer_info->skb = NULL;
+ }
+ }
+
+ /* there also may be some cached data from a chained receive */
+ if (rx_ring->rx_skb_top) {
+ dev_kfree_skb(rx_ring->rx_skb_top);
+ rx_ring->rx_skb_top = NULL;
+ }
+
+ size = sizeof(struct e1000_buffer) * rx_ring->count;
+ memset(rx_ring->buffer_info, 0, size);
+
+ /* Zero out the descriptor ring */
+ memset(rx_ring->desc, 0, rx_ring->size);
+
+ rx_ring->next_to_clean = 0;
+ rx_ring->next_to_use = 0;
+
+ writel(0, hw->hw_addr + rx_ring->rdh);
+ writel(0, hw->hw_addr + rx_ring->rdt);
+}
+
+/**
+ * e1000_clean_all_rx_rings - Free Rx Buffers for all queues
+ * @adapter: board private structure
+ **/
+
+static void e1000_clean_all_rx_rings(struct e1000_adapter *adapter)
+{
+ int i;
+
+ for (i = 0; i < adapter->num_rx_queues; i++)
+ e1000_clean_rx_ring(adapter, &adapter->rx_ring[i]);
+}
+
+/* The 82542 2.0 (revision 2) needs to have the receive unit in reset
+ * and memory write and invalidate disabled for certain operations
+ */
+static void e1000_enter_82542_rst(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u32 rctl;
+
+ e1000_pci_clear_mwi(hw);
+
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_RST;
+ ew32(RCTL, rctl);
+ E1000_WRITE_FLUSH();
+ mdelay(5);
+
+ if (netif_running(netdev))
+ e1000_clean_all_rx_rings(adapter);
+}
+
+static void e1000_leave_82542_rst(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u32 rctl;
+
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_RST;
+ ew32(RCTL, rctl);
+ E1000_WRITE_FLUSH();
+ mdelay(5);
+
+ if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE)
+ e1000_pci_set_mwi(hw);
+
+ if (netif_running(netdev)) {
+ /* No need to loop, because 82542 supports only 1 queue */
+ struct e1000_rx_ring *ring = &adapter->rx_ring[0];
+ e1000_configure_rx(adapter);
+ adapter->alloc_rx_buf(adapter, ring, E1000_DESC_UNUSED(ring));
+ }
+}
+
+/**
+ * e1000_set_mac - Change the Ethernet Address of the NIC
+ * @netdev: network interface device structure
+ * @p: pointer to an address structure
+ *
+ * Returns 0 on success, negative on failure
+ **/
+
+static int e1000_set_mac(struct net_device *netdev, void *p)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct sockaddr *addr = p;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ /* 82542 2.0 needs to be in reset to write receive address registers */
+
+ if (hw->mac_type == e1000_82542_rev2_0)
+ e1000_enter_82542_rst(adapter);
+
+ memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
+ memcpy(hw->mac_addr, addr->sa_data, netdev->addr_len);
+
+ e1000_rar_set(hw, hw->mac_addr, 0);
+
+ if (hw->mac_type == e1000_82542_rev2_0)
+ e1000_leave_82542_rst(adapter);
+
+ return 0;
+}
+
+/**
+ * e1000_set_rx_mode - Secondary Unicast, Multicast and Promiscuous mode set
+ * @netdev: network interface device structure
+ *
+ * The set_rx_mode entry point is called whenever the unicast or multicast
+ * address lists or the network interface flags are updated. This routine is
+ * responsible for configuring the hardware for proper unicast, multicast,
+ * promiscuous mode, and all-multi behavior.
+ **/
+
+static void e1000_set_rx_mode(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct netdev_hw_addr *ha;
+ bool use_uc = false;
+ struct dev_addr_list *mc_ptr;
+ u32 rctl;
+ u32 hash_value;
+ int i, rar_entries = E1000_RAR_ENTRIES;
+ int mta_reg_count = E1000_NUM_MTA_REGISTERS;
+ u32 *mcarray = kcalloc(mta_reg_count, sizeof(u32), GFP_ATOMIC);
+
+ if (!mcarray) {
+ DPRINTK(PROBE, ERR, "memory allocation failed\n");
+ return;
+ }
+
+ /* Check for Promiscuous and All Multicast modes */
+
+ rctl = er32(RCTL);
+
+ if (netdev->flags & IFF_PROMISC) {
+ rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE);
+ rctl &= ~E1000_RCTL_VFE;
+ } else {
+ if (netdev->flags & IFF_ALLMULTI)
+ rctl |= E1000_RCTL_MPE;
+ else
+ rctl &= ~E1000_RCTL_MPE;
+ /* Enable VLAN filter if there is a VLAN */
+ if (adapter->vlgrp)
+ rctl |= E1000_RCTL_VFE;
+ }
+
+ if (netdev->uc.count > rar_entries - 1) {
+ rctl |= E1000_RCTL_UPE;
+ } else if (!(netdev->flags & IFF_PROMISC)) {
+ rctl &= ~E1000_RCTL_UPE;
+ use_uc = true;
+ }
+
+ ew32(RCTL, rctl);
+
+ /* 82542 2.0 needs to be in reset to write receive address registers */
+
+ if (hw->mac_type == e1000_82542_rev2_0)
+ e1000_enter_82542_rst(adapter);
+
+ /* load the first 14 addresses into the exact filters 1-14. Unicast
+ * addresses take precedence to avoid disabling unicast filtering
+ * when possible.
+ *
+ * RAR 0 is used for the station MAC adddress
+ * if there are not 14 addresses, go ahead and clear the filters
+ */
+ i = 1;
+ if (use_uc)
+ list_for_each_entry(ha, &netdev->uc.list, list) {
+ if (i == rar_entries)
+ break;
+ e1000_rar_set(hw, ha->addr, i++);
+ }
+
+ WARN_ON(i == rar_entries);
+
+ mc_ptr = netdev->mc_list;
+
+ for (; i < rar_entries; i++) {
+ if (mc_ptr) {
+ e1000_rar_set(hw, mc_ptr->da_addr, i);
+ mc_ptr = mc_ptr->next;
+ } else {
+ E1000_WRITE_REG_ARRAY(hw, RA, i << 1, 0);
+ E1000_WRITE_FLUSH();
+ E1000_WRITE_REG_ARRAY(hw, RA, (i << 1) + 1, 0);
+ E1000_WRITE_FLUSH();
+ }
+ }
+
+ /* load any remaining addresses into the hash table */
+
+ for (; mc_ptr; mc_ptr = mc_ptr->next) {
+ u32 hash_reg, hash_bit, mta;
+ hash_value = e1000_hash_mc_addr(hw, mc_ptr->da_addr);
+ hash_reg = (hash_value >> 5) & 0x7F;
+ hash_bit = hash_value & 0x1F;
+ mta = (1 << hash_bit);
+ mcarray[hash_reg] |= mta;
+ }
+
+ /* write the hash table completely, write from bottom to avoid
+ * both stupid write combining chipsets, and flushing each write */
+ for (i = mta_reg_count - 1; i >= 0 ; i--) {
+ /*
+ * If we are on an 82544 has an errata where writing odd
+ * offsets overwrites the previous even offset, but writing
+ * backwards over the range solves the issue by always
+ * writing the odd offset first
+ */
+ E1000_WRITE_REG_ARRAY(hw, MTA, i, mcarray[i]);
+ }
+ E1000_WRITE_FLUSH();
+
+ if (hw->mac_type == e1000_82542_rev2_0)
+ e1000_leave_82542_rst(adapter);
+
+ kfree(mcarray);
+}
+
+/* Need to wait a few seconds after link up to get diagnostic information from
+ * the phy */
+
+static void e1000_update_phy_info(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *)data;
+ struct e1000_hw *hw = &adapter->hw;
+ e1000_phy_get_info(hw, &adapter->phy_info);
+}
+
+/**
+ * e1000_82547_tx_fifo_stall - Timer Call-back
+ * @data: pointer to adapter cast into an unsigned long
+ **/
+
+static void e1000_82547_tx_fifo_stall(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *)data;
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u32 tctl;
+
+ if (atomic_read(&adapter->tx_fifo_stall)) {
+ if ((er32(TDT) == er32(TDH)) &&
+ (er32(TDFT) == er32(TDFH)) &&
+ (er32(TDFTS) == er32(TDFHS))) {
+ tctl = er32(TCTL);
+ ew32(TCTL, tctl & ~E1000_TCTL_EN);
+ ew32(TDFT, adapter->tx_head_addr);
+ ew32(TDFH, adapter->tx_head_addr);
+ ew32(TDFTS, adapter->tx_head_addr);
+ ew32(TDFHS, adapter->tx_head_addr);
+ ew32(TCTL, tctl);
+ E1000_WRITE_FLUSH();
+
+ adapter->tx_fifo_head = 0;
+ atomic_set(&adapter->tx_fifo_stall, 0);
+ netif_wake_queue(netdev);
+ } else if (!test_bit(__E1000_DOWN, &adapter->flags)) {
+ mod_timer(&adapter->tx_fifo_stall_timer, jiffies + 1);
+ }
+ }
+}
+
+static bool e1000_has_link(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ bool link_active = false;
+
+ /* get_link_status is set on LSC (link status) interrupt or
+ * rx sequence error interrupt. get_link_status will stay
+ * false until the e1000_check_for_link establishes link
+ * for copper adapters ONLY
+ */
+ switch (hw->media_type) {
+ case e1000_media_type_copper:
+ if (hw->get_link_status) {
+ e1000_check_for_link(hw);
+ link_active = !hw->get_link_status;
+ } else {
+ link_active = true;
+ }
+ break;
+ case e1000_media_type_fiber:
+ e1000_check_for_link(hw);
+ link_active = !!(er32(STATUS) & E1000_STATUS_LU);
+ break;
+ case e1000_media_type_internal_serdes:
+ e1000_check_for_link(hw);
+ link_active = hw->serdes_has_link;
+ break;
+ default:
+ break;
+ }
+
+ return link_active;
+}
+
+/**
+ * e1000_watchdog - Timer Call-back
+ * @data: pointer to adapter cast into an unsigned long
+ **/
+static void e1000_watchdog(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *)data;
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_tx_ring *txdr = adapter->tx_ring;
+ u32 link, tctl;
+
+ link = e1000_has_link(adapter);
+ if ((netif_carrier_ok(netdev)) && link)
+ goto link_up;
+
+ if (link) {
+ if (!netif_carrier_ok(netdev)) {
+ u32 ctrl;
+ bool txb2b = true;
+ /* update snapshot of PHY registers on LSC */
+ e1000_get_speed_and_duplex(hw,
+ &adapter->link_speed,
+ &adapter->link_duplex);
+
+ ctrl = er32(CTRL);
+ printk(KERN_INFO "e1000: %s NIC Link is Up %d Mbps %s, "
+ "Flow Control: %s\n",
+ netdev->name,
+ adapter->link_speed,
+ adapter->link_duplex == FULL_DUPLEX ?
+ "Full Duplex" : "Half Duplex",
+ ((ctrl & E1000_CTRL_TFCE) && (ctrl &
+ E1000_CTRL_RFCE)) ? "RX/TX" : ((ctrl &
+ E1000_CTRL_RFCE) ? "RX" : ((ctrl &
+ E1000_CTRL_TFCE) ? "TX" : "None" )));
+
+ /* tweak tx_queue_len according to speed/duplex
+ * and adjust the timeout factor */
+ netdev->tx_queue_len = adapter->tx_queue_len;
+ adapter->tx_timeout_factor = 1;
+ switch (adapter->link_speed) {
+ case SPEED_10:
+ txb2b = false;
+ netdev->tx_queue_len = 10;
+ adapter->tx_timeout_factor = 16;
+ break;
+ case SPEED_100:
+ txb2b = false;
+ netdev->tx_queue_len = 100;
+ /* maybe add some timeout factor ? */
+ break;
+ }
+
+ /* enable transmits in the hardware */
+ tctl = er32(TCTL);
+ tctl |= E1000_TCTL_EN;
+ ew32(TCTL, tctl);
+
+ netif_carrier_on(netdev);
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->phy_info_timer,
+ round_jiffies(jiffies + 2 * HZ));
+ adapter->smartspeed = 0;
+ }
+ } else {
+ if (netif_carrier_ok(netdev)) {
+ adapter->link_speed = 0;
+ adapter->link_duplex = 0;
+ printk(KERN_INFO "e1000: %s NIC Link is Down\n",
+ netdev->name);
+ netif_carrier_off(netdev);
+
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->phy_info_timer,
+ round_jiffies(jiffies + 2 * HZ));
+ }
+
+ e1000_smartspeed(adapter);
+ }
+
+link_up:
+ e1000_update_stats(adapter);
+
+ hw->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old;
+ adapter->tpt_old = adapter->stats.tpt;
+ hw->collision_delta = adapter->stats.colc - adapter->colc_old;
+ adapter->colc_old = adapter->stats.colc;
+
+ adapter->gorcl = adapter->stats.gorcl - adapter->gorcl_old;
+ adapter->gorcl_old = adapter->stats.gorcl;
+ adapter->gotcl = adapter->stats.gotcl - adapter->gotcl_old;
+ adapter->gotcl_old = adapter->stats.gotcl;
+
+ e1000_update_adaptive(hw);
+
+ if (!netif_carrier_ok(netdev)) {
+ if (E1000_DESC_UNUSED(txdr) + 1 < txdr->count) {
+ /* We've lost link, so the controller stops DMA,
+ * but we've got queued Tx work that's never going
+ * to get done, so reset controller to flush Tx.
+ * (Do the reset outside of interrupt context). */
+ adapter->tx_timeout_count++;
+ schedule_work(&adapter->reset_task);
+ /* return immediately since reset is imminent */
+ return;
+ }
+ }
+
+ /* Cause software interrupt to ensure rx ring is cleaned */
+ ew32(ICS, E1000_ICS_RXDMT0);
+
+ /* Force detection of hung controller every watchdog period */
+ adapter->detect_tx_hung = true;
+
+ /* Reset the timer */
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->watchdog_timer,
+ round_jiffies(jiffies + 2 * HZ));
+}
+
+enum latency_range {
+ lowest_latency = 0,
+ low_latency = 1,
+ bulk_latency = 2,
+ latency_invalid = 255
+};
+
+/**
+ * e1000_update_itr - update the dynamic ITR value based on statistics
+ * @adapter: pointer to adapter
+ * @itr_setting: current adapter->itr
+ * @packets: the number of packets during this measurement interval
+ * @bytes: the number of bytes during this measurement interval
+ *
+ * Stores a new ITR value based on packets and byte
+ * counts during the last interrupt. The advantage of per interrupt
+ * computation is faster updates and more accurate ITR for the current
+ * traffic pattern. Constants in this function were computed
+ * based on theoretical maximum wire speed and thresholds were set based
+ * on testing data as well as attempting to minimize response time
+ * while increasing bulk throughput.
+ * this functionality is controlled by the InterruptThrottleRate module
+ * parameter (see e1000_param.c)
+ **/
+static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
+ u16 itr_setting, int packets, int bytes)
+{
+ unsigned int retval = itr_setting;
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (unlikely(hw->mac_type < e1000_82540))
+ goto update_itr_done;
+
+ if (packets == 0)
+ goto update_itr_done;
+
+ switch (itr_setting) {
+ case lowest_latency:
+ /* jumbo frames get bulk treatment*/
+ if (bytes/packets > 8000)
+ retval = bulk_latency;
+ else if ((packets < 5) && (bytes > 512))
+ retval = low_latency;
+ break;
+ case low_latency: /* 50 usec aka 20000 ints/s */
+ if (bytes > 10000) {
+ /* jumbo frames need bulk latency setting */
+ if (bytes/packets > 8000)
+ retval = bulk_latency;
+ else if ((packets < 10) || ((bytes/packets) > 1200))
+ retval = bulk_latency;
+ else if ((packets > 35))
+ retval = lowest_latency;
+ } else if (bytes/packets > 2000)
+ retval = bulk_latency;
+ else if (packets <= 2 && bytes < 512)
+ retval = lowest_latency;
+ break;
+ case bulk_latency: /* 250 usec aka 4000 ints/s */
+ if (bytes > 25000) {
+ if (packets > 35)
+ retval = low_latency;
+ } else if (bytes < 6000) {
+ retval = low_latency;
+ }
+ break;
+ }
+
+update_itr_done:
+ return retval;
+}
+
+static void e1000_set_itr(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 current_itr;
+ u32 new_itr = adapter->itr;
+
+ if (unlikely(hw->mac_type < e1000_82540))
+ return;
+
+ /* for non-gigabit speeds, just fix the interrupt rate at 4000 */
+ if (unlikely(adapter->link_speed != SPEED_1000)) {
+ current_itr = 0;
+ new_itr = 4000;
+ goto set_itr_now;
+ }
+
+ adapter->tx_itr = e1000_update_itr(adapter,
+ adapter->tx_itr,
+ adapter->total_tx_packets,
+ adapter->total_tx_bytes);
+ /* conservative mode (itr 3) eliminates the lowest_latency setting */
+ if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency)
+ adapter->tx_itr = low_latency;
+
+ adapter->rx_itr = e1000_update_itr(adapter,
+ adapter->rx_itr,
+ adapter->total_rx_packets,
+ adapter->total_rx_bytes);
+ /* conservative mode (itr 3) eliminates the lowest_latency setting */
+ if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency)
+ adapter->rx_itr = low_latency;
+
+ current_itr = max(adapter->rx_itr, adapter->tx_itr);
+
+ switch (current_itr) {
+ /* counts and packets in update_itr are dependent on these numbers */
+ case lowest_latency:
+ new_itr = 70000;
+ break;
+ case low_latency:
+ new_itr = 20000; /* aka hwitr = ~200 */
+ break;
+ case bulk_latency:
+ new_itr = 4000;
+ break;
+ default:
+ break;
+ }
+
+set_itr_now:
+ if (new_itr != adapter->itr) {
+ /* this attempts to bias the interrupt rate towards Bulk
+ * by adding intermediate steps when interrupt rate is
+ * increasing */
+ new_itr = new_itr > adapter->itr ?
+ min(adapter->itr + (new_itr >> 2), new_itr) :
+ new_itr;
+ adapter->itr = new_itr;
+ ew32(ITR, 1000000000 / (new_itr * 256));
+ }
+
+ return;
+}
+
+#define E1000_TX_FLAGS_CSUM 0x00000001
+#define E1000_TX_FLAGS_VLAN 0x00000002
+#define E1000_TX_FLAGS_TSO 0x00000004
+#define E1000_TX_FLAGS_IPV4 0x00000008
+#define E1000_TX_FLAGS_VLAN_MASK 0xffff0000
+#define E1000_TX_FLAGS_VLAN_SHIFT 16
+
+static int e1000_tso(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring, struct sk_buff *skb)
+{
+ struct e1000_context_desc *context_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i;
+ u32 cmd_length = 0;
+ u16 ipcse = 0, tucse, mss;
+ u8 ipcss, ipcso, tucss, tucso, hdr_len;
+ int err;
+
+ if (skb_is_gso(skb)) {
+ if (skb_header_cloned(skb)) {
+ err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
+ if (err)
+ return err;
+ }
+
+ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ mss = skb_shinfo(skb)->gso_size;
+ if (skb->protocol == htons(ETH_P_IP)) {
+ struct iphdr *iph = ip_hdr(skb);
+ iph->tot_len = 0;
+ iph->check = 0;
+ tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr,
+ iph->daddr, 0,
+ IPPROTO_TCP,
+ 0);
+ cmd_length = E1000_TXD_CMD_IP;
+ ipcse = skb_transport_offset(skb) - 1;
+ } else if (skb->protocol == htons(ETH_P_IPV6)) {
+ ipv6_hdr(skb)->payload_len = 0;
+ tcp_hdr(skb)->check =
+ ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
+ &ipv6_hdr(skb)->daddr,
+ 0, IPPROTO_TCP, 0);
+ ipcse = 0;
+ }
+ ipcss = skb_network_offset(skb);
+ ipcso = (void *)&(ip_hdr(skb)->check) - (void *)skb->data;
+ tucss = skb_transport_offset(skb);
+ tucso = (void *)&(tcp_hdr(skb)->check) - (void *)skb->data;
+ tucse = 0;
+
+ cmd_length |= (E1000_TXD_CMD_DEXT | E1000_TXD_CMD_TSE |
+ E1000_TXD_CMD_TCP | (skb->len - (hdr_len)));
+
+ i = tx_ring->next_to_use;
+ context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
+ buffer_info = &tx_ring->buffer_info[i];
+
+ context_desc->lower_setup.ip_fields.ipcss = ipcss;
+ context_desc->lower_setup.ip_fields.ipcso = ipcso;
+ context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse);
+ context_desc->upper_setup.tcp_fields.tucss = tucss;
+ context_desc->upper_setup.tcp_fields.tucso = tucso;
+ context_desc->upper_setup.tcp_fields.tucse = cpu_to_le16(tucse);
+ context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss);
+ context_desc->tcp_seg_setup.fields.hdr_len = hdr_len;
+ context_desc->cmd_and_length = cpu_to_le32(cmd_length);
+
+ buffer_info->time_stamp = jiffies;
+ buffer_info->next_to_watch = i;
+
+ if (++i == tx_ring->count) i = 0;
+ tx_ring->next_to_use = i;
+
+ return true;
+ }
+ return false;
+}
+
+static bool e1000_tx_csum(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring, struct sk_buff *skb)
+{
+ struct e1000_context_desc *context_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i;
+ u8 css;
+ u32 cmd_len = E1000_TXD_CMD_DEXT;
+
+ if (skb->ip_summed != CHECKSUM_PARTIAL)
+ return false;
+
+ switch (skb->protocol) {
+ case cpu_to_be16(ETH_P_IP):
+ if (ip_hdr(skb)->protocol == IPPROTO_TCP)
+ cmd_len |= E1000_TXD_CMD_TCP;
+ break;
+ case cpu_to_be16(ETH_P_IPV6):
+ /* XXX not handling all IPV6 headers */
+ if (ipv6_hdr(skb)->nexthdr == IPPROTO_TCP)
+ cmd_len |= E1000_TXD_CMD_TCP;
+ break;
+ default:
+ if (unlikely(net_ratelimit()))
+ DPRINTK(DRV, WARNING,
+ "checksum_partial proto=%x!\n", skb->protocol);
+ break;
+ }
+
+ css = skb_transport_offset(skb);
+
+ i = tx_ring->next_to_use;
+ buffer_info = &tx_ring->buffer_info[i];
+ context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
+
+ context_desc->lower_setup.ip_config = 0;
+ context_desc->upper_setup.tcp_fields.tucss = css;
+ context_desc->upper_setup.tcp_fields.tucso =
+ css + skb->csum_offset;
+ context_desc->upper_setup.tcp_fields.tucse = 0;
+ context_desc->tcp_seg_setup.data = 0;
+ context_desc->cmd_and_length = cpu_to_le32(cmd_len);
+
+ buffer_info->time_stamp = jiffies;
+ buffer_info->next_to_watch = i;
+
+ if (unlikely(++i == tx_ring->count)) i = 0;
+ tx_ring->next_to_use = i;
+
+ return true;
+}
+
+#define E1000_MAX_TXD_PWR 12
+#define E1000_MAX_DATA_PER_TXD (1<<E1000_MAX_TXD_PWR)
+
+static int e1000_tx_map(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring,
+ struct sk_buff *skb, unsigned int first,
+ unsigned int max_per_txd, unsigned int nr_frags,
+ unsigned int mss)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_buffer *buffer_info;
+ unsigned int len = skb_headlen(skb);
+ unsigned int offset, size, count = 0, i;
+ unsigned int f;
+ dma_addr_t *map;
+
+ i = tx_ring->next_to_use;
+
+ if (skb_dma_map(&adapter->pdev->dev, skb, DMA_TO_DEVICE)) {
+ dev_err(&adapter->pdev->dev, "TX DMA map failed\n");
+ return 0;
+ }
+
+ map = skb_shinfo(skb)->dma_maps;
+ offset = 0;
+
+ while (len) {
+ buffer_info = &tx_ring->buffer_info[i];
+ size = min(len, max_per_txd);
+ /* Workaround for Controller erratum --
+ * descriptor for non-tso packet in a linear SKB that follows a
+ * tso gets written back prematurely before the data is fully
+ * DMA'd to the controller */
+ if (!skb->data_len && tx_ring->last_tx_tso &&
+ !skb_is_gso(skb)) {
+ tx_ring->last_tx_tso = 0;
+ size -= 4;
+ }
+
+ /* Workaround for premature desc write-backs
+ * in TSO mode. Append 4-byte sentinel desc */
+ if (unlikely(mss && !nr_frags && size == len && size > 8))
+ size -= 4;
+ /* work-around for errata 10 and it applies
+ * to all controllers in PCI-X mode
+ * The fix is to make sure that the first descriptor of a
+ * packet is smaller than 2048 - 16 - 16 (or 2016) bytes
+ */
+ if (unlikely((hw->bus_type == e1000_bus_type_pcix) &&
+ (size > 2015) && count == 0))
+ size = 2015;
+
+ /* Workaround for potential 82544 hang in PCI-X. Avoid
+ * terminating buffers within evenly-aligned dwords. */
+ if (unlikely(adapter->pcix_82544 &&
+ !((unsigned long)(skb->data + offset + size - 1) & 4) &&
+ size > 4))
+ size -= 4;
+
+ buffer_info->length = size;
+ /* set time_stamp *before* dma to help avoid a possible race */
+ buffer_info->time_stamp = jiffies;
+ buffer_info->dma = skb_shinfo(skb)->dma_head + offset;
+ buffer_info->next_to_watch = i;
+
+ len -= size;
+ offset += size;
+ count++;
+ if (len) {
+ i++;
+ if (unlikely(i == tx_ring->count))
+ i = 0;
+ }
+ }
+
+ for (f = 0; f < nr_frags; f++) {
+ struct skb_frag_struct *frag;
+
+ frag = &skb_shinfo(skb)->frags[f];
+ len = frag->size;
+ offset = 0;
+
+ while (len) {
+ i++;
+ if (unlikely(i == tx_ring->count))
+ i = 0;
+
+ buffer_info = &tx_ring->buffer_info[i];
+ size = min(len, max_per_txd);
+ /* Workaround for premature desc write-backs
+ * in TSO mode. Append 4-byte sentinel desc */
+ if (unlikely(mss && f == (nr_frags-1) && size == len && size > 8))
+ size -= 4;
+ /* Workaround for potential 82544 hang in PCI-X.
+ * Avoid terminating buffers within evenly-aligned
+ * dwords. */
+ if (unlikely(adapter->pcix_82544 &&
+ !((unsigned long)(page_to_phys(frag->page) + offset
+ + size - 1) & 4) &&
+ size > 4))
+ size -= 4;
+
+ buffer_info->length = size;
+ buffer_info->time_stamp = jiffies;
+ buffer_info->dma = map[f] + offset;
+ buffer_info->next_to_watch = i;
+
+ len -= size;
+ offset += size;
+ count++;
+ }
+ }
+
+ tx_ring->buffer_info[i].skb = skb;
+ tx_ring->buffer_info[first].next_to_watch = i;
+
+ return count;
+}
+
+static void e1000_tx_queue(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring, int tx_flags,
+ int count)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_tx_desc *tx_desc = NULL;
+ struct e1000_buffer *buffer_info;
+ u32 txd_upper = 0, txd_lower = E1000_TXD_CMD_IFCS;
+ unsigned int i;
+
+ if (likely(tx_flags & E1000_TX_FLAGS_TSO)) {
+ txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D |
+ E1000_TXD_CMD_TSE;
+ txd_upper |= E1000_TXD_POPTS_TXSM << 8;
+
+ if (likely(tx_flags & E1000_TX_FLAGS_IPV4))
+ txd_upper |= E1000_TXD_POPTS_IXSM << 8;
+ }
+
+ if (likely(tx_flags & E1000_TX_FLAGS_CSUM)) {
+ txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
+ txd_upper |= E1000_TXD_POPTS_TXSM << 8;
+ }
+
+ if (unlikely(tx_flags & E1000_TX_FLAGS_VLAN)) {
+ txd_lower |= E1000_TXD_CMD_VLE;
+ txd_upper |= (tx_flags & E1000_TX_FLAGS_VLAN_MASK);
+ }
+
+ i = tx_ring->next_to_use;
+
+ while (count--) {
+ buffer_info = &tx_ring->buffer_info[i];
+ tx_desc = E1000_TX_DESC(*tx_ring, i);
+ tx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+ tx_desc->lower.data =
+ cpu_to_le32(txd_lower | buffer_info->length);
+ tx_desc->upper.data = cpu_to_le32(txd_upper);
+ if (unlikely(++i == tx_ring->count)) i = 0;
+ }
+
+ tx_desc->lower.data |= cpu_to_le32(adapter->txd_cmd);
+
+ /* Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64). */
+ wmb();
+
+ tx_ring->next_to_use = i;
+ writel(i, hw->hw_addr + tx_ring->tdt);
+ /* we need this if more than one processor can write to our tail
+ * at a time, it syncronizes IO on IA64/Altix systems */
+ mmiowb();
+}
+
+/**
+ * 82547 workaround to avoid controller hang in half-duplex environment.
+ * The workaround is to avoid queuing a large packet that would span
+ * the internal Tx FIFO ring boundary by notifying the stack to resend
+ * the packet at a later time. This gives the Tx FIFO an opportunity to
+ * flush all packets. When that occurs, we reset the Tx FIFO pointers
+ * to the beginning of the Tx FIFO.
+ **/
+
+#define E1000_FIFO_HDR 0x10
+#define E1000_82547_PAD_LEN 0x3E0
+
+static int e1000_82547_fifo_workaround(struct e1000_adapter *adapter,
+ struct sk_buff *skb)
+{
+ u32 fifo_space = adapter->tx_fifo_size - adapter->tx_fifo_head;
+ u32 skb_fifo_len = skb->len + E1000_FIFO_HDR;
+
+ skb_fifo_len = ALIGN(skb_fifo_len, E1000_FIFO_HDR);
+
+ if (adapter->link_duplex != HALF_DUPLEX)
+ goto no_fifo_stall_required;
+
+ if (atomic_read(&adapter->tx_fifo_stall))
+ return 1;
+
+ if (skb_fifo_len >= (E1000_82547_PAD_LEN + fifo_space)) {
+ atomic_set(&adapter->tx_fifo_stall, 1);
+ return 1;
+ }
+
+no_fifo_stall_required:
+ adapter->tx_fifo_head += skb_fifo_len;
+ if (adapter->tx_fifo_head >= adapter->tx_fifo_size)
+ adapter->tx_fifo_head -= adapter->tx_fifo_size;
+ return 0;
+}
+
+static int __e1000_maybe_stop_tx(struct net_device *netdev, int size)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_tx_ring *tx_ring = adapter->tx_ring;
+
+ netif_stop_queue(netdev);
+ /* Herbert's original patch had:
+ * smp_mb__after_netif_stop_queue();
+ * but since that doesn't exist yet, just open code it. */
+ smp_mb();
+
+ /* We need to check again in a case another CPU has just
+ * made room available. */
+ if (likely(E1000_DESC_UNUSED(tx_ring) < size))
+ return -EBUSY;
+
+ /* A reprieve! */
+ netif_start_queue(netdev);
+ ++adapter->restart_queue;
+ return 0;
+}
+
+static int e1000_maybe_stop_tx(struct net_device *netdev,
+ struct e1000_tx_ring *tx_ring, int size)
+{
+ if (likely(E1000_DESC_UNUSED(tx_ring) >= size))
+ return 0;
+ return __e1000_maybe_stop_tx(netdev, size);
+}
+
+#define TXD_USE_COUNT(S, X) (((S) >> (X)) + 1 )
+static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
+ struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_tx_ring *tx_ring;
+ unsigned int first, max_per_txd = E1000_MAX_DATA_PER_TXD;
+ unsigned int max_txd_pwr = E1000_MAX_TXD_PWR;
+ unsigned int tx_flags = 0;
+ unsigned int len = skb->len - skb->data_len;
+ unsigned int nr_frags;
+ unsigned int mss;
+ int count = 0;
+ int tso;
+ unsigned int f;
+
+ /* This goes back to the question of how to logically map a tx queue
+ * to a flow. Right now, performance is impacted slightly negatively
+ * if using multiple tx queues. If the stack breaks away from a
+ * single qdisc implementation, we can look at this again. */
+ tx_ring = adapter->tx_ring;
+
+ if (unlikely(skb->len <= 0)) {
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
+ mss = skb_shinfo(skb)->gso_size;
+ /* The controller does a simple calculation to
+ * make sure there is enough room in the FIFO before
+ * initiating the DMA for each buffer. The calc is:
+ * 4 = ceil(buffer len/mss). To make sure we don't
+ * overrun the FIFO, adjust the max buffer len if mss
+ * drops. */
+ if (mss) {
+ u8 hdr_len;
+ max_per_txd = min(mss << 2, max_per_txd);
+ max_txd_pwr = fls(max_per_txd) - 1;
+
+ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ if (skb->data_len && hdr_len == len) {
+ switch (hw->mac_type) {
+ unsigned int pull_size;
+ case e1000_82544:
+ /* Make sure we have room to chop off 4 bytes,
+ * and that the end alignment will work out to
+ * this hardware's requirements
+ * NOTE: this is a TSO only workaround
+ * if end byte alignment not correct move us
+ * into the next dword */
+ if ((unsigned long)(skb_tail_pointer(skb) - 1) & 4)
+ break;
+ /* fall through */
+ pull_size = min((unsigned int)4, skb->data_len);
+ if (!__pskb_pull_tail(skb, pull_size)) {
+ DPRINTK(DRV, ERR,
+ "__pskb_pull_tail failed.\n");
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+ len = skb->len - skb->data_len;
+ break;
+ default:
+ /* do nothing */
+ break;
+ }
+ }
+ }
+
+ /* reserve a descriptor for the offload context */
+ if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
+ count++;
+ count++;
+
+ /* Controller Erratum workaround */
+ if (!skb->data_len && tx_ring->last_tx_tso && !skb_is_gso(skb))
+ count++;
+
+ count += TXD_USE_COUNT(len, max_txd_pwr);
+
+ if (adapter->pcix_82544)
+ count++;
+
+ /* work-around for errata 10 and it applies to all controllers
+ * in PCI-X mode, so add one more descriptor to the count
+ */
+ if (unlikely((hw->bus_type == e1000_bus_type_pcix) &&
+ (len > 2015)))
+ count++;
+
+ nr_frags = skb_shinfo(skb)->nr_frags;
+ for (f = 0; f < nr_frags; f++)
+ count += TXD_USE_COUNT(skb_shinfo(skb)->frags[f].size,
+ max_txd_pwr);
+ if (adapter->pcix_82544)
+ count += nr_frags;
+
+ /* need: count + 2 desc gap to keep tail from touching
+ * head, otherwise try next time */
+ if (unlikely(e1000_maybe_stop_tx(netdev, tx_ring, count + 2)))
+ return NETDEV_TX_BUSY;
+
+ if (unlikely(hw->mac_type == e1000_82547)) {
+ if (unlikely(e1000_82547_fifo_workaround(adapter, skb))) {
+ netif_stop_queue(netdev);
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->tx_fifo_stall_timer,
+ jiffies + 1);
+ return NETDEV_TX_BUSY;
+ }
+ }
+
+ if (unlikely(adapter->vlgrp && vlan_tx_tag_present(skb))) {
+ tx_flags |= E1000_TX_FLAGS_VLAN;
+ tx_flags |= (vlan_tx_tag_get(skb) << E1000_TX_FLAGS_VLAN_SHIFT);
+ }
+
+ first = tx_ring->next_to_use;
+
+ tso = e1000_tso(adapter, tx_ring, skb);
+ if (tso < 0) {
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
+ if (likely(tso)) {
+ if (likely(hw->mac_type != e1000_82544))
+ tx_ring->last_tx_tso = 1;
+ tx_flags |= E1000_TX_FLAGS_TSO;
+ } else if (likely(e1000_tx_csum(adapter, tx_ring, skb)))
+ tx_flags |= E1000_TX_FLAGS_CSUM;
+
+ if (likely(skb->protocol == htons(ETH_P_IP)))
+ tx_flags |= E1000_TX_FLAGS_IPV4;
+
+ count = e1000_tx_map(adapter, tx_ring, skb, first, max_per_txd,
+ nr_frags, mss);
+
+ if (count) {
+ e1000_tx_queue(adapter, tx_ring, tx_flags, count);
+ /* Make sure there is space in the ring for the next send. */
+ e1000_maybe_stop_tx(netdev, tx_ring, MAX_SKB_FRAGS + 2);
+
+ } else {
+ dev_kfree_skb_any(skb);
+ tx_ring->buffer_info[first].time_stamp = 0;
+ tx_ring->next_to_use = first;
+ }
+
+ return NETDEV_TX_OK;
+}
+
+/**
+ * e1000_tx_timeout - Respond to a Tx Hang
+ * @netdev: network interface device structure
+ **/
+
+static void e1000_tx_timeout(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ /* Do the reset outside of interrupt context */
+ adapter->tx_timeout_count++;
+ schedule_work(&adapter->reset_task);
+}
+
+static void e1000_reset_task(struct work_struct *work)
+{
+ struct e1000_adapter *adapter =
+ container_of(work, struct e1000_adapter, reset_task);
+
+ e1000_reinit_locked(adapter);
+}
+
+/**
+ * e1000_get_stats - Get System Network Statistics
+ * @netdev: network interface device structure
+ *
+ * Returns the address of the device statistics structure.
+ * The statistics are actually updated from the timer callback.
+ **/
+
+static struct net_device_stats *e1000_get_stats(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ /* only return the current stats */
+ return &adapter->net_stats;
+}
+
+/**
+ * e1000_change_mtu - Change the Maximum Transfer Unit
+ * @netdev: network interface device structure
+ * @new_mtu: new value for maximum frame size
+ *
+ * Returns 0 on success, negative on failure
+ **/
+
+static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ int max_frame = new_mtu + ENET_HEADER_SIZE + ETHERNET_FCS_SIZE;
+
+ if ((max_frame < MINIMUM_ETHERNET_FRAME_SIZE) ||
+ (max_frame > MAX_JUMBO_FRAME_SIZE)) {
+ DPRINTK(PROBE, ERR, "Invalid MTU setting\n");
+ return -EINVAL;
+ }
+
+ /* Adapter-specific max frame size limits. */
+ switch (hw->mac_type) {
+ case e1000_undefined ... e1000_82542_rev2_1:
+ if (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)) {
+ DPRINTK(PROBE, ERR, "Jumbo Frames not supported.\n");
+ return -EINVAL;
+ }
+ break;
+ default:
+ /* Capable of supporting up to MAX_JUMBO_FRAME_SIZE limit. */
+ break;
+ }
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+ /* e1000_down has a dependency on max_frame_size */
+ hw->max_frame_size = max_frame;
+ if (netif_running(netdev))
+ e1000_down(adapter);
+
+ /* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
+ * means we reserve 2 more, this pushes us to allocate from the next
+ * larger slab size.
+ * i.e. RXBUFFER_2048 --> size-4096 slab
+ * however with the new *_jumbo_rx* routines, jumbo receives will use
+ * fragmented skbs */
+
+ if (max_frame <= E1000_RXBUFFER_2048)
+ adapter->rx_buffer_len = E1000_RXBUFFER_2048;
+ else
+#if (PAGE_SIZE >= E1000_RXBUFFER_16384)
+ adapter->rx_buffer_len = E1000_RXBUFFER_16384;
+#elif (PAGE_SIZE >= E1000_RXBUFFER_4096)
+ adapter->rx_buffer_len = PAGE_SIZE;
+#endif
+
+ /* adjust allocation if LPE protects us, and we aren't using SBP */
+ if (!hw->tbi_compatibility_on &&
+ ((max_frame == (ETH_FRAME_LEN + ETH_FCS_LEN)) ||
+ (max_frame == MAXIMUM_ETHERNET_VLAN_SIZE)))
+ adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
+
+ printk(KERN_INFO "e1000: %s changing MTU from %d to %d\n",
+ netdev->name, netdev->mtu, new_mtu);
+ netdev->mtu = new_mtu;
+
+ if (netif_running(netdev))
+ e1000_up(adapter);
+ else
+ e1000_reset(adapter);
+
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+
+ return 0;
+}
+
+/**
+ * e1000_update_stats - Update the board statistics counters
+ * @adapter: board private structure
+ **/
+
+void e1000_update_stats(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct pci_dev *pdev = adapter->pdev;
+ unsigned long flags;
+ u16 phy_tmp;
+
+#define PHY_IDLE_ERROR_COUNT_MASK 0x00FF
+
+ /*
+ * Prevent stats update while adapter is being reset, or if the pci
+ * connection is down.
+ */
+ if (adapter->link_speed == 0)
+ return;
+ if (pci_channel_offline(pdev))
+ return;
+
+ spin_lock_irqsave(&adapter->stats_lock, flags);
+
+ /* these counters are modified from e1000_tbi_adjust_stats,
+ * called from the interrupt context, so they must only
+ * be written while holding adapter->stats_lock
+ */
+
+ adapter->stats.crcerrs += er32(CRCERRS);
+ adapter->stats.gprc += er32(GPRC);
+ adapter->stats.gorcl += er32(GORCL);
+ adapter->stats.gorch += er32(GORCH);
+ adapter->stats.bprc += er32(BPRC);
+ adapter->stats.mprc += er32(MPRC);
+ adapter->stats.roc += er32(ROC);
+
+ adapter->stats.prc64 += er32(PRC64);
+ adapter->stats.prc127 += er32(PRC127);
+ adapter->stats.prc255 += er32(PRC255);
+ adapter->stats.prc511 += er32(PRC511);
+ adapter->stats.prc1023 += er32(PRC1023);
+ adapter->stats.prc1522 += er32(PRC1522);
+
+ adapter->stats.symerrs += er32(SYMERRS);
+ adapter->stats.mpc += er32(MPC);
+ adapter->stats.scc += er32(SCC);
+ adapter->stats.ecol += er32(ECOL);
+ adapter->stats.mcc += er32(MCC);
+ adapter->stats.latecol += er32(LATECOL);
+ adapter->stats.dc += er32(DC);
+ adapter->stats.sec += er32(SEC);
+ adapter->stats.rlec += er32(RLEC);
+ adapter->stats.xonrxc += er32(XONRXC);
+ adapter->stats.xontxc += er32(XONTXC);
+ adapter->stats.xoffrxc += er32(XOFFRXC);
+ adapter->stats.xofftxc += er32(XOFFTXC);
+ adapter->stats.fcruc += er32(FCRUC);
+ adapter->stats.gptc += er32(GPTC);
+ adapter->stats.gotcl += er32(GOTCL);
+ adapter->stats.gotch += er32(GOTCH);
+ adapter->stats.rnbc += er32(RNBC);
+ adapter->stats.ruc += er32(RUC);
+ adapter->stats.rfc += er32(RFC);
+ adapter->stats.rjc += er32(RJC);
+ adapter->stats.torl += er32(TORL);
+ adapter->stats.torh += er32(TORH);
+ adapter->stats.totl += er32(TOTL);
+ adapter->stats.toth += er32(TOTH);
+ adapter->stats.tpr += er32(TPR);
+
+ adapter->stats.ptc64 += er32(PTC64);
+ adapter->stats.ptc127 += er32(PTC127);
+ adapter->stats.ptc255 += er32(PTC255);
+ adapter->stats.ptc511 += er32(PTC511);
+ adapter->stats.ptc1023 += er32(PTC1023);
+ adapter->stats.ptc1522 += er32(PTC1522);
+
+ adapter->stats.mptc += er32(MPTC);
+ adapter->stats.bptc += er32(BPTC);
+
+ /* used for adaptive IFS */
+
+ hw->tx_packet_delta = er32(TPT);
+ adapter->stats.tpt += hw->tx_packet_delta;
+ hw->collision_delta = er32(COLC);
+ adapter->stats.colc += hw->collision_delta;
+
+ if (hw->mac_type >= e1000_82543) {
+ adapter->stats.algnerrc += er32(ALGNERRC);
+ adapter->stats.rxerrc += er32(RXERRC);
+ adapter->stats.tncrs += er32(TNCRS);
+ adapter->stats.cexterr += er32(CEXTERR);
+ adapter->stats.tsctc += er32(TSCTC);
+ adapter->stats.tsctfc += er32(TSCTFC);
+ }
+
+ /* Fill out the OS statistics structure */
+ adapter->net_stats.multicast = adapter->stats.mprc;
+ adapter->net_stats.collisions = adapter->stats.colc;
+
+ /* Rx Errors */
+
+ /* RLEC on some newer hardware can be incorrect so build
+ * our own version based on RUC and ROC */
+ adapter->net_stats.rx_errors = adapter->stats.rxerrc +
+ adapter->stats.crcerrs + adapter->stats.algnerrc +
+ adapter->stats.ruc + adapter->stats.roc +
+ adapter->stats.cexterr;
+ adapter->stats.rlerrc = adapter->stats.ruc + adapter->stats.roc;
+ adapter->net_stats.rx_length_errors = adapter->stats.rlerrc;
+ adapter->net_stats.rx_crc_errors = adapter->stats.crcerrs;
+ adapter->net_stats.rx_frame_errors = adapter->stats.algnerrc;
+ adapter->net_stats.rx_missed_errors = adapter->stats.mpc;
+
+ /* Tx Errors */
+ adapter->stats.txerrc = adapter->stats.ecol + adapter->stats.latecol;
+ adapter->net_stats.tx_errors = adapter->stats.txerrc;
+ adapter->net_stats.tx_aborted_errors = adapter->stats.ecol;
+ adapter->net_stats.tx_window_errors = adapter->stats.latecol;
+ adapter->net_stats.tx_carrier_errors = adapter->stats.tncrs;
+ if (hw->bad_tx_carr_stats_fd &&
+ adapter->link_duplex == FULL_DUPLEX) {
+ adapter->net_stats.tx_carrier_errors = 0;
+ adapter->stats.tncrs = 0;
+ }
+
+ /* Tx Dropped needs to be maintained elsewhere */
+
+ /* Phy Stats */
+ if (hw->media_type == e1000_media_type_copper) {
+ if ((adapter->link_speed == SPEED_1000) &&
+ (!e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_tmp))) {
+ phy_tmp &= PHY_IDLE_ERROR_COUNT_MASK;
+ adapter->phy_stats.idle_errors += phy_tmp;
+ }
+
+ if ((hw->mac_type <= e1000_82546) &&
+ (hw->phy_type == e1000_phy_m88) &&
+ !e1000_read_phy_reg(hw, M88E1000_RX_ERR_CNTR, &phy_tmp))
+ adapter->phy_stats.receive_errors += phy_tmp;
+ }
+
+ /* Management Stats */
+ if (hw->has_smbus) {
+ adapter->stats.mgptc += er32(MGTPTC);
+ adapter->stats.mgprc += er32(MGTPRC);
+ adapter->stats.mgpdc += er32(MGTPDC);
+ }
+
+ spin_unlock_irqrestore(&adapter->stats_lock, flags);
+}
+
+/**
+ * e1000_intr - Interrupt Handler
+ * @irq: interrupt number
+ * @data: pointer to a network interface device structure
+ **/
+
+static irqreturn_t e1000_intr(int irq, void *data)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 icr = er32(ICR);
+
+ if (unlikely((!icr) || test_bit(__E1000_DOWN, &adapter->flags)))
+ return IRQ_NONE; /* Not our interrupt */
+
+ if (unlikely(icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC))) {
+ hw->get_link_status = 1;
+ /* guard against interrupt when we're going down */
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->watchdog_timer, jiffies + 1);
+ }
+
+ /* disable interrupts, without the synchronize_irq bit */
+ ew32(IMC, ~0);
+ E1000_WRITE_FLUSH();
+
+ if (likely(napi_schedule_prep(&adapter->napi))) {
+ adapter->total_tx_bytes = 0;
+ adapter->total_tx_packets = 0;
+ adapter->total_rx_bytes = 0;
+ adapter->total_rx_packets = 0;
+ __napi_schedule(&adapter->napi);
+ } else {
+ /* this really should not happen! if it does it is basically a
+ * bug, but not a hard error, so enable ints and continue */
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_enable(adapter);
+ }
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * e1000_clean - NAPI Rx polling callback
+ * @adapter: board private structure
+ **/
+static int e1000_clean(struct napi_struct *napi, int budget)
+{
+ struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, napi);
+ int tx_clean_complete = 0, work_done = 0;
+
+ tx_clean_complete = e1000_clean_tx_irq(adapter, &adapter->tx_ring[0]);
+
+ adapter->clean_rx(adapter, &adapter->rx_ring[0], &work_done, budget);
+
+ if (!tx_clean_complete)
+ work_done = budget;
+
+ /* If budget not fully consumed, exit the polling mode */
+ if (work_done < budget) {
+ if (likely(adapter->itr_setting & 3))
+ e1000_set_itr(adapter);
+ napi_complete(napi);
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_enable(adapter);
+ }
+
+ return work_done;
+}
+
+/**
+ * e1000_clean_tx_irq - Reclaim resources after transmit completes
+ * @adapter: board private structure
+ **/
+static bool e1000_clean_tx_irq(struct e1000_adapter *adapter,
+ struct e1000_tx_ring *tx_ring)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_tx_desc *tx_desc, *eop_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i, eop;
+ unsigned int count = 0;
+ unsigned int total_tx_bytes=0, total_tx_packets=0;
+
+ i = tx_ring->next_to_clean;
+ eop = tx_ring->buffer_info[i].next_to_watch;
+ eop_desc = E1000_TX_DESC(*tx_ring, eop);
+
+ while ((eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) &&
+ (count < tx_ring->count)) {
+ bool cleaned = false;
+ for ( ; !cleaned; count++) {
+ tx_desc = E1000_TX_DESC(*tx_ring, i);
+ buffer_info = &tx_ring->buffer_info[i];
+ cleaned = (i == eop);
+
+ if (cleaned) {
+ struct sk_buff *skb = buffer_info->skb;
+ unsigned int segs, bytecount;
+ segs = skb_shinfo(skb)->gso_segs ?: 1;
+ /* multiply data chunks by size of headers */
+ bytecount = ((segs - 1) * skb_headlen(skb)) +
+ skb->len;
+ total_tx_packets += segs;
+ total_tx_bytes += bytecount;
+ }
+ e1000_unmap_and_free_tx_resource(adapter, buffer_info);
+ tx_desc->upper.data = 0;
+
+ if (unlikely(++i == tx_ring->count)) i = 0;
+ }
+
+ eop = tx_ring->buffer_info[i].next_to_watch;
+ eop_desc = E1000_TX_DESC(*tx_ring, eop);
+ }
+
+ tx_ring->next_to_clean = i;
+
+#define TX_WAKE_THRESHOLD 32
+ if (unlikely(count && netif_carrier_ok(netdev) &&
+ E1000_DESC_UNUSED(tx_ring) >= TX_WAKE_THRESHOLD)) {
+ /* Make sure that anybody stopping the queue after this
+ * sees the new next_to_clean.
+ */
+ smp_mb();
+
+ if (netif_queue_stopped(netdev) &&
+ !(test_bit(__E1000_DOWN, &adapter->flags))) {
+ netif_wake_queue(netdev);
+ ++adapter->restart_queue;
+ }
+ }
+
+ if (adapter->detect_tx_hung) {
+ /* Detect a transmit hang in hardware, this serializes the
+ * check with the clearing of time_stamp and movement of i */
+ adapter->detect_tx_hung = false;
+ if (tx_ring->buffer_info[eop].time_stamp &&
+ time_after(jiffies, tx_ring->buffer_info[eop].time_stamp +
+ (adapter->tx_timeout_factor * HZ))
+ && !(er32(STATUS) & E1000_STATUS_TXOFF)) {
+
+ /* detected Tx unit hang */
+ DPRINTK(DRV, ERR, "Detected Tx Unit Hang\n"
+ " Tx Queue <%lu>\n"
+ " TDH <%x>\n"
+ " TDT <%x>\n"
+ " next_to_use <%x>\n"
+ " next_to_clean <%x>\n"
+ "buffer_info[next_to_clean]\n"
+ " time_stamp <%lx>\n"
+ " next_to_watch <%x>\n"
+ " jiffies <%lx>\n"
+ " next_to_watch.status <%x>\n",
+ (unsigned long)((tx_ring - adapter->tx_ring) /
+ sizeof(struct e1000_tx_ring)),
+ readl(hw->hw_addr + tx_ring->tdh),
+ readl(hw->hw_addr + tx_ring->tdt),
+ tx_ring->next_to_use,
+ tx_ring->next_to_clean,
+ tx_ring->buffer_info[eop].time_stamp,
+ eop,
+ jiffies,
+ eop_desc->upper.fields.status);
+ netif_stop_queue(netdev);
+ }
+ }
+ adapter->total_tx_bytes += total_tx_bytes;
+ adapter->total_tx_packets += total_tx_packets;
+ adapter->net_stats.tx_bytes += total_tx_bytes;
+ adapter->net_stats.tx_packets += total_tx_packets;
+ return (count < tx_ring->count);
+}
+
+/**
+ * e1000_rx_checksum - Receive Checksum Offload for 82543
+ * @adapter: board private structure
+ * @status_err: receive descriptor status and error fields
+ * @csum: receive descriptor csum field
+ * @sk_buff: socket buffer with received data
+ **/
+
+static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
+ u32 csum, struct sk_buff *skb)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 status = (u16)status_err;
+ u8 errors = (u8)(status_err >> 24);
+ skb->ip_summed = CHECKSUM_NONE;
+
+ /* 82543 or newer only */
+ if (unlikely(hw->mac_type < e1000_82543)) return;
+ /* Ignore Checksum bit is set */
+ if (unlikely(status & E1000_RXD_STAT_IXSM)) return;
+ /* TCP/UDP checksum error bit is set */
+ if (unlikely(errors & E1000_RXD_ERR_TCPE)) {
+ /* let the stack verify checksum errors */
+ adapter->hw_csum_err++;
+ return;
+ }
+ /* TCP/UDP Checksum has not been calculated */
+ if (!(status & E1000_RXD_STAT_TCPCS))
+ return;
+
+ /* It must be a TCP or UDP packet with a valid checksum */
+ if (likely(status & E1000_RXD_STAT_TCPCS)) {
+ /* TCP checksum is good */
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+ }
+ adapter->hw_csum_good++;
+}
+
+/**
+ * e1000_consume_page - helper function
+ **/
+static void e1000_consume_page(struct e1000_buffer *bi, struct sk_buff *skb,
+ u16 length)
+{
+ bi->page = NULL;
+ skb->len += length;
+ skb->data_len += length;
+ skb->truesize += length;
+}
+
+/**
+ * e1000_receive_skb - helper function to handle rx indications
+ * @adapter: board private structure
+ * @status: descriptor status field as written by hardware
+ * @vlan: descriptor vlan field as written by hardware (no le/be conversion)
+ * @skb: pointer to sk_buff to be indicated to stack
+ */
+static void e1000_receive_skb(struct e1000_adapter *adapter, u8 status,
+ __le16 vlan, struct sk_buff *skb)
+{
+ if (unlikely(adapter->vlgrp && (status & E1000_RXD_STAT_VP))) {
+ vlan_hwaccel_receive_skb(skb, adapter->vlgrp,
+ le16_to_cpu(vlan) &
+ E1000_RXD_SPC_VLAN_MASK);
+ } else {
+ netif_receive_skb(skb);
+ }
+}
+
+/**
+ * e1000_clean_jumbo_rx_irq - Send received data up the network stack; legacy
+ * @adapter: board private structure
+ * @rx_ring: ring to clean
+ * @work_done: amount of napi work completed this call
+ * @work_to_do: max amount of work allowed for this call to do
+ *
+ * the return value indicates whether actual cleaning was done, there
+ * is no guarantee that everything was cleaned
+ */
+static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int *work_done, int work_to_do)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_rx_desc *rx_desc, *next_rxd;
+ struct e1000_buffer *buffer_info, *next_buffer;
+ unsigned long irq_flags;
+ u32 length;
+ unsigned int i;
+ int cleaned_count = 0;
+ bool cleaned = false;
+ unsigned int total_rx_bytes=0, total_rx_packets=0;
+
+ i = rx_ring->next_to_clean;
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (rx_desc->status & E1000_RXD_STAT_DD) {
+ struct sk_buff *skb;
+ u8 status;
+
+ if (*work_done >= work_to_do)
+ break;
+ (*work_done)++;
+
+ status = rx_desc->status;
+ skb = buffer_info->skb;
+ buffer_info->skb = NULL;
+
+ if (++i == rx_ring->count) i = 0;
+ next_rxd = E1000_RX_DESC(*rx_ring, i);
+ prefetch(next_rxd);
+
+ next_buffer = &rx_ring->buffer_info[i];
+
+ cleaned = true;
+ cleaned_count++;
+ pci_unmap_page(pdev, buffer_info->dma, buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+ buffer_info->dma = 0;
+
+ length = le16_to_cpu(rx_desc->length);
+
+ /* errors is only valid for DD + EOP descriptors */
+ if (unlikely((status & E1000_RXD_STAT_EOP) &&
+ (rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK))) {
+ u8 last_byte = *(skb->data + length - 1);
+ if (TBI_ACCEPT(hw, status, rx_desc->errors, length,
+ last_byte)) {
+ spin_lock_irqsave(&adapter->stats_lock,
+ irq_flags);
+ e1000_tbi_adjust_stats(hw, &adapter->stats,
+ length, skb->data);
+ spin_unlock_irqrestore(&adapter->stats_lock,
+ irq_flags);
+ length--;
+ } else {
+ /* recycle both page and skb */
+ buffer_info->skb = skb;
+ /* an error means any chain goes out the window
+ * too */
+ if (rx_ring->rx_skb_top)
+ dev_kfree_skb(rx_ring->rx_skb_top);
+ rx_ring->rx_skb_top = NULL;
+ goto next_desc;
+ }
+ }
+
+#define rxtop rx_ring->rx_skb_top
+ if (!(status & E1000_RXD_STAT_EOP)) {
+ /* this descriptor is only the beginning (or middle) */
+ if (!rxtop) {
+ /* this is the beginning of a chain */
+ rxtop = skb;
+ skb_fill_page_desc(rxtop, 0, buffer_info->page,
+ 0, length);
+ } else {
+ /* this is the middle of a chain */
+ skb_fill_page_desc(rxtop,
+ skb_shinfo(rxtop)->nr_frags,
+ buffer_info->page, 0, length);
+ /* re-use the skb, only consumed the page */
+ buffer_info->skb = skb;
+ }
+ e1000_consume_page(buffer_info, rxtop, length);
+ goto next_desc;
+ } else {
+ if (rxtop) {
+ /* end of the chain */
+ skb_fill_page_desc(rxtop,
+ skb_shinfo(rxtop)->nr_frags,
+ buffer_info->page, 0, length);
+ /* re-use the current skb, we only consumed the
+ * page */
+ buffer_info->skb = skb;
+ skb = rxtop;
+ rxtop = NULL;
+ e1000_consume_page(buffer_info, skb, length);
+ } else {
+ /* no chain, got EOP, this buf is the packet
+ * copybreak to save the put_page/alloc_page */
+ if (length <= copybreak &&
+ skb_tailroom(skb) >= length) {
+ u8 *vaddr;
+ vaddr = kmap_atomic(buffer_info->page,
+ KM_SKB_DATA_SOFTIRQ);
+ memcpy(skb_tail_pointer(skb), vaddr, length);
+ kunmap_atomic(vaddr,
+ KM_SKB_DATA_SOFTIRQ);
+ /* re-use the page, so don't erase
+ * buffer_info->page */
+ skb_put(skb, length);
+ } else {
+ skb_fill_page_desc(skb, 0,
+ buffer_info->page, 0,
+ length);
+ e1000_consume_page(buffer_info, skb,
+ length);
+ }
+ }
+ }
+
+ /* Receive Checksum Offload XXX recompute due to CRC strip? */
+ e1000_rx_checksum(adapter,
+ (u32)(status) |
+ ((u32)(rx_desc->errors) << 24),
+ le16_to_cpu(rx_desc->csum), skb);
+
+ pskb_trim(skb, skb->len - 4);
+
+ /* probably a little skewed due to removing CRC */
+ total_rx_bytes += skb->len;
+ total_rx_packets++;
+
+ /* eth type trans needs skb->data to point to something */
+ if (!pskb_may_pull(skb, ETH_HLEN)) {
+ DPRINTK(DRV, ERR, "pskb_may_pull failed.\n");
+ dev_kfree_skb(skb);
+ goto next_desc;
+ }
+
+ skb->protocol = eth_type_trans(skb, netdev);
+
+ e1000_receive_skb(adapter, status, rx_desc->special, skb);
+
+next_desc:
+ rx_desc->status = 0;
+
+ /* return some buffers to hardware, one at a time is too slow */
+ if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
+ adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
+ cleaned_count = 0;
+ }
+
+ /* use prefetched values */
+ rx_desc = next_rxd;
+ buffer_info = next_buffer;
+ }
+ rx_ring->next_to_clean = i;
+
+ cleaned_count = E1000_DESC_UNUSED(rx_ring);
+ if (cleaned_count)
+ adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
+
+ adapter->total_rx_packets += total_rx_packets;
+ adapter->total_rx_bytes += total_rx_bytes;
+ adapter->net_stats.rx_bytes += total_rx_bytes;
+ adapter->net_stats.rx_packets += total_rx_packets;
+ return cleaned;
+}
+
+/**
+ * e1000_clean_rx_irq - Send received data up the network stack; legacy
+ * @adapter: board private structure
+ * @rx_ring: ring to clean
+ * @work_done: amount of napi work completed this call
+ * @work_to_do: max amount of work allowed for this call to do
+ */
+static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int *work_done, int work_to_do)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_rx_desc *rx_desc, *next_rxd;
+ struct e1000_buffer *buffer_info, *next_buffer;
+ unsigned long flags;
+ u32 length;
+ unsigned int i;
+ int cleaned_count = 0;
+ bool cleaned = false;
+ unsigned int total_rx_bytes=0, total_rx_packets=0;
+
+ i = rx_ring->next_to_clean;
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (rx_desc->status & E1000_RXD_STAT_DD) {
+ struct sk_buff *skb;
+ u8 status;
+
+ if (*work_done >= work_to_do)
+ break;
+ (*work_done)++;
+
+ status = rx_desc->status;
+ skb = buffer_info->skb;
+ buffer_info->skb = NULL;
+
+ prefetch(skb->data - NET_IP_ALIGN);
+
+ if (++i == rx_ring->count) i = 0;
+ next_rxd = E1000_RX_DESC(*rx_ring, i);
+ prefetch(next_rxd);
+
+ next_buffer = &rx_ring->buffer_info[i];
+
+ cleaned = true;
+ cleaned_count++;
+ pci_unmap_single(pdev, buffer_info->dma, buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+ buffer_info->dma = 0;
+
+ length = le16_to_cpu(rx_desc->length);
+ /* !EOP means multiple descriptors were used to store a single
+ * packet, if thats the case we need to toss it. In fact, we
+ * to toss every packet with the EOP bit clear and the next
+ * frame that _does_ have the EOP bit set, as it is by
+ * definition only a frame fragment
+ */
+ if (unlikely(!(status & E1000_RXD_STAT_EOP)))
+ adapter->discarding = true;
+
+ if (adapter->discarding) {
+ /* All receives must fit into a single buffer */
+ E1000_DBG("%s: Receive packet consumed multiple"
+ " buffers\n", netdev->name);
+ /* recycle */
+ buffer_info->skb = skb;
+ if (status & E1000_RXD_STAT_EOP)
+ adapter->discarding = false;
+ goto next_desc;
+ }
+
+ if (unlikely(rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK)) {
+ u8 last_byte = *(skb->data + length - 1);
+ if (TBI_ACCEPT(hw, status, rx_desc->errors, length,
+ last_byte)) {
+ spin_lock_irqsave(&adapter->stats_lock, flags);
+ e1000_tbi_adjust_stats(hw, &adapter->stats,
+ length, skb->data);
+ spin_unlock_irqrestore(&adapter->stats_lock,
+ flags);
+ length--;
+ } else {
+ /* recycle */
+ buffer_info->skb = skb;
+ goto next_desc;
+ }
+ }
+
+ /* adjust length to remove Ethernet CRC, this must be
+ * done after the TBI_ACCEPT workaround above */
+ length -= 4;
+
+ /* probably a little skewed due to removing CRC */
+ total_rx_bytes += length;
+ total_rx_packets++;
+
+ /* code added for copybreak, this should improve
+ * performance for small packets with large amounts
+ * of reassembly being done in the stack */
+ if (length < copybreak) {
+ struct sk_buff *new_skb =
+ netdev_alloc_skb(netdev, length + NET_IP_ALIGN);
+ if (new_skb) {
+ skb_reserve(new_skb, NET_IP_ALIGN);
+ skb_copy_to_linear_data_offset(new_skb,
+ -NET_IP_ALIGN,
+ (skb->data -
+ NET_IP_ALIGN),
+ (length +
+ NET_IP_ALIGN));
+ /* save the skb in buffer_info as good */
+ buffer_info->skb = skb;
+ skb = new_skb;
+ }
+ /* else just continue with the old one */
+ }
+ /* end copybreak code */
+ skb_put(skb, length);
+
+ /* Receive Checksum Offload */
+ e1000_rx_checksum(adapter,
+ (u32)(status) |
+ ((u32)(rx_desc->errors) << 24),
+ le16_to_cpu(rx_desc->csum), skb);
+
+ skb->protocol = eth_type_trans(skb, netdev);
+
+ e1000_receive_skb(adapter, status, rx_desc->special, skb);
+
+next_desc:
+ rx_desc->status = 0;
+
+ /* return some buffers to hardware, one at a time is too slow */
+ if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
+ adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
+ cleaned_count = 0;
+ }
+
+ /* use prefetched values */
+ rx_desc = next_rxd;
+ buffer_info = next_buffer;
+ }
+ rx_ring->next_to_clean = i;
+
+ cleaned_count = E1000_DESC_UNUSED(rx_ring);
+ if (cleaned_count)
+ adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
+
+ adapter->total_rx_packets += total_rx_packets;
+ adapter->total_rx_bytes += total_rx_bytes;
+ adapter->net_stats.rx_bytes += total_rx_bytes;
+ adapter->net_stats.rx_packets += total_rx_packets;
+ return cleaned;
+}
+
+/**
+ * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers
+ * @adapter: address of board private structure
+ * @rx_ring: pointer to receive ring structure
+ * @cleaned_count: number of buffers to allocate this pass
+ **/
+
+static void
+e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring, int cleaned_count)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_rx_desc *rx_desc;
+ struct e1000_buffer *buffer_info;
+ struct sk_buff *skb;
+ unsigned int i;
+ unsigned int bufsz = 256 -
+ 16 /*for skb_reserve */ -
+ NET_IP_ALIGN;
+
+ i = rx_ring->next_to_use;
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (cleaned_count--) {
+ skb = buffer_info->skb;
+ if (skb) {
+ skb_trim(skb, 0);
+ goto check_page;
+ }
+
+ skb = netdev_alloc_skb(netdev, bufsz);
+ if (unlikely(!skb)) {
+ /* Better luck next round */
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ /* Fix for errata 23, can't cross 64kB boundary */
+ if (!e1000_check_64k_bound(adapter, skb->data, bufsz)) {
+ struct sk_buff *oldskb = skb;
+ DPRINTK(PROBE, ERR, "skb align check failed: %u bytes "
+ "at %p\n", bufsz, skb->data);
+ /* Try again, without freeing the previous */
+ skb = netdev_alloc_skb(netdev, bufsz);
+ /* Failed allocation, critical failure */
+ if (!skb) {
+ dev_kfree_skb(oldskb);
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ if (!e1000_check_64k_bound(adapter, skb->data, bufsz)) {
+ /* give up */
+ dev_kfree_skb(skb);
+ dev_kfree_skb(oldskb);
+ break; /* while (cleaned_count--) */
+ }
+
+ /* Use new allocation */
+ dev_kfree_skb(oldskb);
+ }
+ /* Make buffer alignment 2 beyond a 16 byte boundary
+ * this will result in a 16 byte aligned IP header after
+ * the 14 byte MAC header is removed
+ */
+ skb_reserve(skb, NET_IP_ALIGN);
+
+ buffer_info->skb = skb;
+ buffer_info->length = adapter->rx_buffer_len;
+check_page:
+ /* allocate a new page if necessary */
+ if (!buffer_info->page) {
+ buffer_info->page = alloc_page(GFP_ATOMIC);
+ if (unlikely(!buffer_info->page)) {
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+ }
+
+ if (!buffer_info->dma)
+ buffer_info->dma = pci_map_page(pdev,
+ buffer_info->page, 0,
+ buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+
+ if (unlikely(++i == rx_ring->count))
+ i = 0;
+ buffer_info = &rx_ring->buffer_info[i];
+ }
+
+ if (likely(rx_ring->next_to_use != i)) {
+ rx_ring->next_to_use = i;
+ if (unlikely(i-- == 0))
+ i = (rx_ring->count - 1);
+
+ /* Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64). */
+ wmb();
+ writel(i, adapter->hw.hw_addr + rx_ring->rdt);
+ }
+}
+
+/**
+ * e1000_alloc_rx_buffers - Replace used receive buffers; legacy & extended
+ * @adapter: address of board private structure
+ **/
+
+static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
+ struct e1000_rx_ring *rx_ring,
+ int cleaned_count)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_rx_desc *rx_desc;
+ struct e1000_buffer *buffer_info;
+ struct sk_buff *skb;
+ unsigned int i;
+ unsigned int bufsz = adapter->rx_buffer_len + NET_IP_ALIGN;
+
+ i = rx_ring->next_to_use;
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (cleaned_count--) {
+ skb = buffer_info->skb;
+ if (skb) {
+ skb_trim(skb, 0);
+ goto map_skb;
+ }
+
+ skb = netdev_alloc_skb(netdev, bufsz);
+ if (unlikely(!skb)) {
+ /* Better luck next round */
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ /* Fix for errata 23, can't cross 64kB boundary */
+ if (!e1000_check_64k_bound(adapter, skb->data, bufsz)) {
+ struct sk_buff *oldskb = skb;
+ DPRINTK(RX_ERR, ERR, "skb align check failed: %u bytes "
+ "at %p\n", bufsz, skb->data);
+ /* Try again, without freeing the previous */
+ skb = netdev_alloc_skb(netdev, bufsz);
+ /* Failed allocation, critical failure */
+ if (!skb) {
+ dev_kfree_skb(oldskb);
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ if (!e1000_check_64k_bound(adapter, skb->data, bufsz)) {
+ /* give up */
+ dev_kfree_skb(skb);
+ dev_kfree_skb(oldskb);
+ adapter->alloc_rx_buff_failed++;
+ break; /* while !buffer_info->skb */
+ }
+
+ /* Use new allocation */
+ dev_kfree_skb(oldskb);
+ }
+ /* Make buffer alignment 2 beyond a 16 byte boundary
+ * this will result in a 16 byte aligned IP header after
+ * the 14 byte MAC header is removed
+ */
+ skb_reserve(skb, NET_IP_ALIGN);
+
+ buffer_info->skb = skb;
+ buffer_info->length = adapter->rx_buffer_len;
+map_skb:
+ buffer_info->dma = pci_map_single(pdev,
+ skb->data,
+ buffer_info->length,
+ PCI_DMA_FROMDEVICE);
+
+ /*
+ * XXX if it was allocated cleanly it will never map to a
+ * boundary crossing
+ */
+
+ /* Fix for errata 23, can't cross 64kB boundary */
+ if (!e1000_check_64k_bound(adapter,
+ (void *)(unsigned long)buffer_info->dma,
+ adapter->rx_buffer_len)) {
+ DPRINTK(RX_ERR, ERR,
+ "dma align check failed: %u bytes at %p\n",
+ adapter->rx_buffer_len,
+ (void *)(unsigned long)buffer_info->dma);
+ dev_kfree_skb(skb);
+ buffer_info->skb = NULL;
+
+ pci_unmap_single(pdev, buffer_info->dma,
+ adapter->rx_buffer_len,
+ PCI_DMA_FROMDEVICE);
+ buffer_info->dma = 0;
+
+ adapter->alloc_rx_buff_failed++;
+ break; /* while !buffer_info->skb */
+ }
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+
+ if (unlikely(++i == rx_ring->count))
+ i = 0;
+ buffer_info = &rx_ring->buffer_info[i];
+ }
+
+ if (likely(rx_ring->next_to_use != i)) {
+ rx_ring->next_to_use = i;
+ if (unlikely(i-- == 0))
+ i = (rx_ring->count - 1);
+
+ /* Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64). */
+ wmb();
+ writel(i, hw->hw_addr + rx_ring->rdt);
+ }
+}
+
+/**
+ * e1000_smartspeed - Workaround for SmartSpeed on 82541 and 82547 controllers.
+ * @adapter:
+ **/
+
+static void e1000_smartspeed(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 phy_status;
+ u16 phy_ctrl;
+
+ if ((hw->phy_type != e1000_phy_igp) || !hw->autoneg ||
+ !(hw->autoneg_advertised & ADVERTISE_1000_FULL))
+ return;
+
+ if (adapter->smartspeed == 0) {
+ /* If Master/Slave config fault is asserted twice,
+ * we assume back-to-back */
+ e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_status);
+ if (!(phy_status & SR_1000T_MS_CONFIG_FAULT)) return;
+ e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_status);
+ if (!(phy_status & SR_1000T_MS_CONFIG_FAULT)) return;
+ e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_ctrl);
+ if (phy_ctrl & CR_1000T_MS_ENABLE) {
+ phy_ctrl &= ~CR_1000T_MS_ENABLE;
+ e1000_write_phy_reg(hw, PHY_1000T_CTRL,
+ phy_ctrl);
+ adapter->smartspeed++;
+ if (!e1000_phy_setup_autoneg(hw) &&
+ !e1000_read_phy_reg(hw, PHY_CTRL,
+ &phy_ctrl)) {
+ phy_ctrl |= (MII_CR_AUTO_NEG_EN |
+ MII_CR_RESTART_AUTO_NEG);
+ e1000_write_phy_reg(hw, PHY_CTRL,
+ phy_ctrl);
+ }
+ }
+ return;
+ } else if (adapter->smartspeed == E1000_SMARTSPEED_DOWNSHIFT) {
+ /* If still no link, perhaps using 2/3 pair cable */
+ e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_ctrl);
+ phy_ctrl |= CR_1000T_MS_ENABLE;
+ e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_ctrl);
+ if (!e1000_phy_setup_autoneg(hw) &&
+ !e1000_read_phy_reg(hw, PHY_CTRL, &phy_ctrl)) {
+ phy_ctrl |= (MII_CR_AUTO_NEG_EN |
+ MII_CR_RESTART_AUTO_NEG);
+ e1000_write_phy_reg(hw, PHY_CTRL, phy_ctrl);
+ }
+ }
+ /* Restart process after E1000_SMARTSPEED_MAX iterations */
+ if (adapter->smartspeed++ == E1000_SMARTSPEED_MAX)
+ adapter->smartspeed = 0;
+}
+
+/**
+ * e1000_ioctl -
+ * @netdev:
+ * @ifreq:
+ * @cmd:
+ **/
+
+static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
+{
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ case SIOCGMIIREG:
+ case SIOCSMIIREG:
+ return e1000_mii_ioctl(netdev, ifr, cmd);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+/**
+ * e1000_mii_ioctl -
+ * @netdev:
+ * @ifreq:
+ * @cmd:
+ **/
+
+static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
+ int cmd)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct mii_ioctl_data *data = if_mii(ifr);
+ int retval;
+ u16 mii_reg;
+ u16 spddplx;
+ unsigned long flags;
+
+ if (hw->media_type != e1000_media_type_copper)
+ return -EOPNOTSUPP;
+
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ data->phy_id = hw->phy_addr;
+ break;
+ case SIOCGMIIREG:
+ spin_lock_irqsave(&adapter->stats_lock, flags);
+ if (e1000_read_phy_reg(hw, data->reg_num & 0x1F,
+ &data->val_out)) {
+ spin_unlock_irqrestore(&adapter->stats_lock, flags);
+ return -EIO;
+ }
+ spin_unlock_irqrestore(&adapter->stats_lock, flags);
+ break;
+ case SIOCSMIIREG:
+ if (data->reg_num & ~(0x1F))
+ return -EFAULT;
+ mii_reg = data->val_in;
+ spin_lock_irqsave(&adapter->stats_lock, flags);
+ if (e1000_write_phy_reg(hw, data->reg_num,
+ mii_reg)) {
+ spin_unlock_irqrestore(&adapter->stats_lock, flags);
+ return -EIO;
+ }
+ spin_unlock_irqrestore(&adapter->stats_lock, flags);
+ if (hw->media_type == e1000_media_type_copper) {
+ switch (data->reg_num) {
+ case PHY_CTRL:
+ if (mii_reg & MII_CR_POWER_DOWN)
+ break;
+ if (mii_reg & MII_CR_AUTO_NEG_EN) {
+ hw->autoneg = 1;
+ hw->autoneg_advertised = 0x2F;
+ } else {
+ if (mii_reg & 0x40)
+ spddplx = SPEED_1000;
+ else if (mii_reg & 0x2000)
+ spddplx = SPEED_100;
+ else
+ spddplx = SPEED_10;
+ spddplx += (mii_reg & 0x100)
+ ? DUPLEX_FULL :
+ DUPLEX_HALF;
+ retval = e1000_set_spd_dplx(adapter,
+ spddplx);
+ if (retval)
+ return retval;
+ }
+ if (netif_running(adapter->netdev))
+ e1000_reinit_locked(adapter);
+ else
+ e1000_reset(adapter);
+ break;
+ case M88E1000_PHY_SPEC_CTRL:
+ case M88E1000_EXT_PHY_SPEC_CTRL:
+ if (e1000_phy_reset(hw))
+ return -EIO;
+ break;
+ }
+ } else {
+ switch (data->reg_num) {
+ case PHY_CTRL:
+ if (mii_reg & MII_CR_POWER_DOWN)
+ break;
+ if (netif_running(adapter->netdev))
+ e1000_reinit_locked(adapter);
+ else
+ e1000_reset(adapter);
+ break;
+ }
+ }
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+ return E1000_SUCCESS;
+}
+
+void e1000_pci_set_mwi(struct e1000_hw *hw)
+{
+ struct e1000_adapter *adapter = hw->back;
+ int ret_val = pci_set_mwi(adapter->pdev);
+
+ if (ret_val)
+ DPRINTK(PROBE, ERR, "Error in setting MWI\n");
+}
+
+void e1000_pci_clear_mwi(struct e1000_hw *hw)
+{
+ struct e1000_adapter *adapter = hw->back;
+
+ pci_clear_mwi(adapter->pdev);
+}
+
+int e1000_pcix_get_mmrbc(struct e1000_hw *hw)
+{
+ struct e1000_adapter *adapter = hw->back;
+ return pcix_get_mmrbc(adapter->pdev);
+}
+
+void e1000_pcix_set_mmrbc(struct e1000_hw *hw, int mmrbc)
+{
+ struct e1000_adapter *adapter = hw->back;
+ pcix_set_mmrbc(adapter->pdev, mmrbc);
+}
+
+void e1000_io_write(struct e1000_hw *hw, unsigned long port, u32 value)
+{
+ outl(value, port);
+}
+
+static void e1000_vlan_rx_register(struct net_device *netdev,
+ struct vlan_group *grp)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl, rctl;
+
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_disable(adapter);
+ adapter->vlgrp = grp;
+
+ if (grp) {
+ /* enable VLAN tag insert/strip */
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_VME;
+ ew32(CTRL, ctrl);
+
+ /* enable VLAN receive filtering */
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_CFIEN;
+ if (!(netdev->flags & IFF_PROMISC))
+ rctl |= E1000_RCTL_VFE;
+ ew32(RCTL, rctl);
+ e1000_update_mng_vlan(adapter);
+ } else {
+ /* disable VLAN tag insert/strip */
+ ctrl = er32(CTRL);
+ ctrl &= ~E1000_CTRL_VME;
+ ew32(CTRL, ctrl);
+
+ /* disable VLAN receive filtering */
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_VFE;
+ ew32(RCTL, rctl);
+
+ if (adapter->mng_vlan_id != (u16)E1000_MNG_VLAN_NONE) {
+ e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+ }
+ }
+
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_enable(adapter);
+}
+
+static void e1000_vlan_rx_add_vid(struct net_device *netdev, u16 vid)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 vfta, index;
+
+ if ((hw->mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
+ (vid == adapter->mng_vlan_id))
+ return;
+ /* add VID to filter table */
+ index = (vid >> 5) & 0x7F;
+ vfta = E1000_READ_REG_ARRAY(hw, VFTA, index);
+ vfta |= (1 << (vid & 0x1F));
+ e1000_write_vfta(hw, index, vfta);
+}
+
+static void e1000_vlan_rx_kill_vid(struct net_device *netdev, u16 vid)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 vfta, index;
+
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_disable(adapter);
+ vlan_group_set_device(adapter->vlgrp, vid, NULL);
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ e1000_irq_enable(adapter);
+
+ /* remove VID from filter table */
+ index = (vid >> 5) & 0x7F;
+ vfta = E1000_READ_REG_ARRAY(hw, VFTA, index);
+ vfta &= ~(1 << (vid & 0x1F));
+ e1000_write_vfta(hw, index, vfta);
+}
+
+static void e1000_restore_vlan(struct e1000_adapter *adapter)
+{
+ e1000_vlan_rx_register(adapter->netdev, adapter->vlgrp);
+
+ if (adapter->vlgrp) {
+ u16 vid;
+ for (vid = 0; vid < VLAN_GROUP_ARRAY_LEN; vid++) {
+ if (!vlan_group_get_device(adapter->vlgrp, vid))
+ continue;
+ e1000_vlan_rx_add_vid(adapter->netdev, vid);
+ }
+ }
+}
+
+int e1000_set_spd_dplx(struct e1000_adapter *adapter, u16 spddplx)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ hw->autoneg = 0;
+
+ /* Fiber NICs only allow 1000 gbps Full duplex */
+ if ((hw->media_type == e1000_media_type_fiber) &&
+ spddplx != (SPEED_1000 + DUPLEX_FULL)) {
+ DPRINTK(PROBE, ERR, "Unsupported Speed/Duplex configuration\n");
+ return -EINVAL;
+ }
+
+ switch (spddplx) {
+ case SPEED_10 + DUPLEX_HALF:
+ hw->forced_speed_duplex = e1000_10_half;
+ break;
+ case SPEED_10 + DUPLEX_FULL:
+ hw->forced_speed_duplex = e1000_10_full;
+ break;
+ case SPEED_100 + DUPLEX_HALF:
+ hw->forced_speed_duplex = e1000_100_half;
+ break;
+ case SPEED_100 + DUPLEX_FULL:
+ hw->forced_speed_duplex = e1000_100_full;
+ break;
+ case SPEED_1000 + DUPLEX_FULL:
+ hw->autoneg = 1;
+ hw->autoneg_advertised = ADVERTISE_1000_FULL;
+ break;
+ case SPEED_1000 + DUPLEX_HALF: /* not supported */
+ default:
+ DPRINTK(PROBE, ERR, "Unsupported Speed/Duplex configuration\n");
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl, ctrl_ext, rctl, status;
+ u32 wufc = adapter->wol;
+#ifdef CONFIG_PM
+ int retval = 0;
+#endif
+
+ netif_device_detach(netdev);
+
+ if (netif_running(netdev)) {
+ WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
+ e1000_down(adapter);
+ }
+
+#ifdef CONFIG_PM
+ retval = pci_save_state(pdev);
+ if (retval)
+ return retval;
+#endif
+
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU)
+ wufc &= ~E1000_WUFC_LNKC;
+
+ if (wufc) {
+ e1000_setup_rctl(adapter);
+ e1000_set_rx_mode(netdev);
+
+ /* turn on all-multi mode if wake on multicast is enabled */
+ if (wufc & E1000_WUFC_MC) {
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_MPE;
+ ew32(RCTL, rctl);
+ }
+
+ if (hw->mac_type >= e1000_82540) {
+ ctrl = er32(CTRL);
+ /* advertise wake from D3Cold */
+ #define E1000_CTRL_ADVD3WUC 0x00100000
+ /* phy power management enable */
+ #define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000
+ ctrl |= E1000_CTRL_ADVD3WUC |
+ E1000_CTRL_EN_PHY_PWR_MGMT;
+ ew32(CTRL, ctrl);
+ }
+
+ if (hw->media_type == e1000_media_type_fiber ||
+ hw->media_type == e1000_media_type_internal_serdes) {
+ /* keep the laser running in D3 */
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_SDP7_DATA;
+ ew32(CTRL_EXT, ctrl_ext);
+ }
+
+ ew32(WUC, E1000_WUC_PME_EN);
+ ew32(WUFC, wufc);
+ } else {
+ ew32(WUC, 0);
+ ew32(WUFC, 0);
+ }
+
+ e1000_release_manageability(adapter);
+
+ *enable_wake = !!wufc;
+
+ /* make sure adapter isn't asleep if manageability is enabled */
+ if (adapter->en_mng_pt)
+ *enable_wake = true;
+
+ if (netif_running(netdev))
+ e1000_free_irq(adapter);
+
+ pci_disable_device(pdev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ int retval;
+ bool wake;
+
+ retval = __e1000_shutdown(pdev, &wake);
+ if (retval)
+ return retval;
+
+ if (wake) {
+ pci_prepare_to_sleep(pdev);
+ } else {
+ pci_wake_from_d3(pdev, false);
+ pci_set_power_state(pdev, PCI_D3hot);
+ }
+
+ return 0;
+}
+
+static int e1000_resume(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 err;
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+
+ if (adapter->need_ioport)
+ err = pci_enable_device(pdev);
+ else
+ err = pci_enable_device_mem(pdev);
+ if (err) {
+ printk(KERN_ERR "e1000: Cannot enable PCI device from suspend\n");
+ return err;
+ }
+ pci_set_master(pdev);
+
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ pci_enable_wake(pdev, PCI_D3cold, 0);
+
+ if (netif_running(netdev)) {
+ err = e1000_request_irq(adapter);
+ if (err)
+ return err;
+ }
+
+ e1000_power_up_phy(adapter);
+ e1000_reset(adapter);
+ ew32(WUS, ~0);
+
+ e1000_init_manageability(adapter);
+
+ if (netif_running(netdev))
+ e1000_up(adapter);
+
+ netif_device_attach(netdev);
+
+ return 0;
+}
+#endif
+
+static void e1000_shutdown(struct pci_dev *pdev)
+{
+ bool wake;
+
+ __e1000_shutdown(pdev, &wake);
+
+ if (system_state == SYSTEM_POWER_OFF) {
+ pci_wake_from_d3(pdev, wake);
+ pci_set_power_state(pdev, PCI_D3hot);
+ }
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+/*
+ * Polling 'interrupt' - used by things like netconsole to send skbs
+ * without having to re-enable interrupts. It's not called while
+ * the interrupt routine is executing.
+ */
+static void e1000_netpoll(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ disable_irq(adapter->pdev->irq);
+ e1000_intr(adapter->pdev->irq, netdev);
+ enable_irq(adapter->pdev->irq);
+}
+#endif
+
+/**
+ * e1000_io_error_detected - called when PCI error is detected
+ * @pdev: Pointer to PCI device
+ * @state: The current pci connection state
+ *
+ * This function is called after a PCI bus error affecting
+ * this device has been detected.
+ */
+static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
+ pci_channel_state_t state)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ netif_device_detach(netdev);
+
+ if (state == pci_channel_io_perm_failure)
+ return PCI_ERS_RESULT_DISCONNECT;
+
+ if (netif_running(netdev))
+ e1000_down(adapter);
+ pci_disable_device(pdev);
+
+ /* Request a slot slot reset. */
+ return PCI_ERS_RESULT_NEED_RESET;
+}
+
+/**
+ * e1000_io_slot_reset - called after the pci bus has been reset.
+ * @pdev: Pointer to PCI device
+ *
+ * Restart the card from scratch, as if from a cold-boot. Implementation
+ * resembles the first-half of the e1000_resume routine.
+ */
+static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ int err;
+
+ if (adapter->need_ioport)
+ err = pci_enable_device(pdev);
+ else
+ err = pci_enable_device_mem(pdev);
+ if (err) {
+ printk(KERN_ERR "e1000: Cannot re-enable PCI device after reset.\n");
+ return PCI_ERS_RESULT_DISCONNECT;
+ }
+ pci_set_master(pdev);
+
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ pci_enable_wake(pdev, PCI_D3cold, 0);
+
+ e1000_reset(adapter);
+ ew32(WUS, ~0);
+
+ return PCI_ERS_RESULT_RECOVERED;
+}
+
+/**
+ * e1000_io_resume - called when traffic can start flowing again.
+ * @pdev: Pointer to PCI device
+ *
+ * This callback is called when the error recovery driver tells us that
+ * its OK to resume normal operation. Implementation resembles the
+ * second-half of the e1000_resume routine.
+ */
+static void e1000_io_resume(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ e1000_init_manageability(adapter);
+
+ if (netif_running(netdev)) {
+ if (e1000_up(adapter)) {
+ printk("e1000: can't bring device back up after reset\n");
+ return;
+ }
+ }
+
+ netif_device_attach(netdev);
+}
+
+/* e1000_main.c */
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_osdep-2.6.32-ethercat.h Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,113 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+
+/* glue for the OS independent part of e1000
+ * includes register access macros
+ */
+
+#ifndef _E1000_OSDEP_H_
+#define _E1000_OSDEP_H_
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <asm/io.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+
+#ifdef DBG
+#define DEBUGOUT(S) printk(KERN_DEBUG S "\n")
+#define DEBUGOUT1(S, A...) printk(KERN_DEBUG S "\n", A)
+#else
+#define DEBUGOUT(S)
+#define DEBUGOUT1(S, A...)
+#endif
+
+#define DEBUGFUNC(F) DEBUGOUT(F "\n")
+#define DEBUGOUT2 DEBUGOUT1
+#define DEBUGOUT3 DEBUGOUT2
+#define DEBUGOUT7 DEBUGOUT3
+
+
+#define er32(reg) \
+ (readl(hw->hw_addr + ((hw->mac_type >= e1000_82543) \
+ ? E1000_##reg : E1000_82542_##reg)))
+
+#define ew32(reg, value) \
+ (writel((value), (hw->hw_addr + ((hw->mac_type >= e1000_82543) \
+ ? E1000_##reg : E1000_82542_##reg))))
+
+#define E1000_WRITE_REG_ARRAY(a, reg, offset, value) ( \
+ writel((value), ((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ ((offset) << 2))))
+
+#define E1000_READ_REG_ARRAY(a, reg, offset) ( \
+ readl((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ ((offset) << 2)))
+
+#define E1000_READ_REG_ARRAY_DWORD E1000_READ_REG_ARRAY
+#define E1000_WRITE_REG_ARRAY_DWORD E1000_WRITE_REG_ARRAY
+
+#define E1000_WRITE_REG_ARRAY_WORD(a, reg, offset, value) ( \
+ writew((value), ((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ ((offset) << 1))))
+
+#define E1000_READ_REG_ARRAY_WORD(a, reg, offset) ( \
+ readw((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ ((offset) << 1)))
+
+#define E1000_WRITE_REG_ARRAY_BYTE(a, reg, offset, value) ( \
+ writeb((value), ((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ (offset))))
+
+#define E1000_READ_REG_ARRAY_BYTE(a, reg, offset) ( \
+ readb((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ (offset)))
+
+#define E1000_WRITE_FLUSH() er32(STATUS)
+
+#define E1000_WRITE_ICH_FLASH_REG(a, reg, value) ( \
+ writel((value), ((a)->flash_address + reg)))
+
+#define E1000_READ_ICH_FLASH_REG(a, reg) ( \
+ readl((a)->flash_address + reg))
+
+#define E1000_WRITE_ICH_FLASH_REG16(a, reg, value) ( \
+ writew((value), ((a)->flash_address + reg)))
+
+#define E1000_READ_ICH_FLASH_REG16(a, reg) ( \
+ readw((a)->flash_address + reg))
+
+#endif /* _E1000_OSDEP_H_ */
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_osdep-2.6.32-orig.h Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,113 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+
+/* glue for the OS independent part of e1000
+ * includes register access macros
+ */
+
+#ifndef _E1000_OSDEP_H_
+#define _E1000_OSDEP_H_
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <asm/io.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+
+#ifdef DBG
+#define DEBUGOUT(S) printk(KERN_DEBUG S "\n")
+#define DEBUGOUT1(S, A...) printk(KERN_DEBUG S "\n", A)
+#else
+#define DEBUGOUT(S)
+#define DEBUGOUT1(S, A...)
+#endif
+
+#define DEBUGFUNC(F) DEBUGOUT(F "\n")
+#define DEBUGOUT2 DEBUGOUT1
+#define DEBUGOUT3 DEBUGOUT2
+#define DEBUGOUT7 DEBUGOUT3
+
+
+#define er32(reg) \
+ (readl(hw->hw_addr + ((hw->mac_type >= e1000_82543) \
+ ? E1000_##reg : E1000_82542_##reg)))
+
+#define ew32(reg, value) \
+ (writel((value), (hw->hw_addr + ((hw->mac_type >= e1000_82543) \
+ ? E1000_##reg : E1000_82542_##reg))))
+
+#define E1000_WRITE_REG_ARRAY(a, reg, offset, value) ( \
+ writel((value), ((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ ((offset) << 2))))
+
+#define E1000_READ_REG_ARRAY(a, reg, offset) ( \
+ readl((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ ((offset) << 2)))
+
+#define E1000_READ_REG_ARRAY_DWORD E1000_READ_REG_ARRAY
+#define E1000_WRITE_REG_ARRAY_DWORD E1000_WRITE_REG_ARRAY
+
+#define E1000_WRITE_REG_ARRAY_WORD(a, reg, offset, value) ( \
+ writew((value), ((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ ((offset) << 1))))
+
+#define E1000_READ_REG_ARRAY_WORD(a, reg, offset) ( \
+ readw((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ ((offset) << 1)))
+
+#define E1000_WRITE_REG_ARRAY_BYTE(a, reg, offset, value) ( \
+ writeb((value), ((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ (offset))))
+
+#define E1000_READ_REG_ARRAY_BYTE(a, reg, offset) ( \
+ readb((a)->hw_addr + \
+ (((a)->mac_type >= e1000_82543) ? E1000_##reg : E1000_82542_##reg) + \
+ (offset)))
+
+#define E1000_WRITE_FLUSH() er32(STATUS)
+
+#define E1000_WRITE_ICH_FLASH_REG(a, reg, value) ( \
+ writel((value), ((a)->flash_address + reg)))
+
+#define E1000_READ_ICH_FLASH_REG(a, reg) ( \
+ readl((a)->flash_address + reg))
+
+#define E1000_WRITE_ICH_FLASH_REG16(a, reg, value) ( \
+ writew((value), ((a)->flash_address + reg)))
+
+#define E1000_READ_ICH_FLASH_REG16(a, reg) ( \
+ readw((a)->flash_address + reg))
+
+#endif /* _E1000_OSDEP_H_ */
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_param-2.6.32-ethercat.c Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,770 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#include "e1000-2.6.32-ethercat.h"
+
+/* This is the only thing that needs to be changed to adjust the
+ * maximum number of ports that the driver can manage.
+ */
+
+#define E1000_MAX_NIC 32
+
+#define OPTION_UNSET -1
+#define OPTION_DISABLED 0
+#define OPTION_ENABLED 1
+
+/* All parameters are treated the same, as an integer array of values.
+ * This macro just reduces the need to repeat the same declaration code
+ * over and over (plus this helps to avoid typo bugs).
+ */
+
+#define E1000_PARAM_INIT { [0 ... E1000_MAX_NIC] = OPTION_UNSET }
+#define E1000_PARAM(X, desc) \
+ static int __devinitdata X[E1000_MAX_NIC+1] = E1000_PARAM_INIT; \
+ static unsigned int num_##X; \
+ module_param_array_named(X, X, int, &num_##X, 0); \
+ MODULE_PARM_DESC(X, desc);
+
+/* Transmit Descriptor Count
+ *
+ * Valid Range: 80-256 for 82542 and 82543 gigabit ethernet controllers
+ * Valid Range: 80-4096 for 82544 and newer
+ *
+ * Default Value: 256
+ */
+E1000_PARAM(TxDescriptors, "Number of transmit descriptors");
+
+/* Receive Descriptor Count
+ *
+ * Valid Range: 80-256 for 82542 and 82543 gigabit ethernet controllers
+ * Valid Range: 80-4096 for 82544 and newer
+ *
+ * Default Value: 256
+ */
+E1000_PARAM(RxDescriptors, "Number of receive descriptors");
+
+/* User Specified Speed Override
+ *
+ * Valid Range: 0, 10, 100, 1000
+ * - 0 - auto-negotiate at all supported speeds
+ * - 10 - only link at 10 Mbps
+ * - 100 - only link at 100 Mbps
+ * - 1000 - only link at 1000 Mbps
+ *
+ * Default Value: 0
+ */
+E1000_PARAM(Speed, "Speed setting");
+
+/* User Specified Duplex Override
+ *
+ * Valid Range: 0-2
+ * - 0 - auto-negotiate for duplex
+ * - 1 - only link at half duplex
+ * - 2 - only link at full duplex
+ *
+ * Default Value: 0
+ */
+E1000_PARAM(Duplex, "Duplex setting");
+
+/* Auto-negotiation Advertisement Override
+ *
+ * Valid Range: 0x01-0x0F, 0x20-0x2F (copper); 0x20 (fiber)
+ *
+ * The AutoNeg value is a bit mask describing which speed and duplex
+ * combinations should be advertised during auto-negotiation.
+ * The supported speed and duplex modes are listed below
+ *
+ * Bit 7 6 5 4 3 2 1 0
+ * Speed (Mbps) N/A N/A 1000 N/A 100 100 10 10
+ * Duplex Full Full Half Full Half
+ *
+ * Default Value: 0x2F (copper); 0x20 (fiber)
+ */
+E1000_PARAM(AutoNeg, "Advertised auto-negotiation setting");
+#define AUTONEG_ADV_DEFAULT 0x2F
+#define AUTONEG_ADV_MASK 0x2F
+
+/* User Specified Flow Control Override
+ *
+ * Valid Range: 0-3
+ * - 0 - No Flow Control
+ * - 1 - Rx only, respond to PAUSE frames but do not generate them
+ * - 2 - Tx only, generate PAUSE frames but ignore them on receive
+ * - 3 - Full Flow Control Support
+ *
+ * Default Value: Read flow control settings from the EEPROM
+ */
+E1000_PARAM(FlowControl, "Flow Control setting");
+#define FLOW_CONTROL_DEFAULT FLOW_CONTROL_FULL
+
+/* XsumRX - Receive Checksum Offload Enable/Disable
+ *
+ * Valid Range: 0, 1
+ * - 0 - disables all checksum offload
+ * - 1 - enables receive IP/TCP/UDP checksum offload
+ * on 82543 and newer -based NICs
+ *
+ * Default Value: 1
+ */
+E1000_PARAM(XsumRX, "Disable or enable Receive Checksum offload");
+
+/* Transmit Interrupt Delay in units of 1.024 microseconds
+ * Tx interrupt delay needs to typically be set to something non zero
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(TxIntDelay, "Transmit Interrupt Delay");
+#define DEFAULT_TIDV 8
+#define MAX_TXDELAY 0xFFFF
+#define MIN_TXDELAY 0
+
+/* Transmit Absolute Interrupt Delay in units of 1.024 microseconds
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(TxAbsIntDelay, "Transmit Absolute Interrupt Delay");
+#define DEFAULT_TADV 32
+#define MAX_TXABSDELAY 0xFFFF
+#define MIN_TXABSDELAY 0
+
+/* Receive Interrupt Delay in units of 1.024 microseconds
+ * hardware will likely hang if you set this to anything but zero.
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(RxIntDelay, "Receive Interrupt Delay");
+#define DEFAULT_RDTR 0
+#define MAX_RXDELAY 0xFFFF
+#define MIN_RXDELAY 0
+
+/* Receive Absolute Interrupt Delay in units of 1.024 microseconds
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(RxAbsIntDelay, "Receive Absolute Interrupt Delay");
+#define DEFAULT_RADV 8
+#define MAX_RXABSDELAY 0xFFFF
+#define MIN_RXABSDELAY 0
+
+/* Interrupt Throttle Rate (interrupts/sec)
+ *
+ * Valid Range: 100-100000 (0=off, 1=dynamic, 3=dynamic conservative)
+ */
+E1000_PARAM(InterruptThrottleRate, "Interrupt Throttling Rate");
+#define DEFAULT_ITR 3
+#define MAX_ITR 100000
+#define MIN_ITR 100
+
+/* Enable Smart Power Down of the PHY
+ *
+ * Valid Range: 0, 1
+ *
+ * Default Value: 0 (disabled)
+ */
+E1000_PARAM(SmartPowerDownEnable, "Enable PHY smart power down");
+
+/* Enable Kumeran Lock Loss workaround
+ *
+ * Valid Range: 0, 1
+ *
+ * Default Value: 1 (enabled)
+ */
+E1000_PARAM(KumeranLockLoss, "Enable Kumeran lock loss workaround");
+
+struct e1000_option {
+ enum { enable_option, range_option, list_option } type;
+ const char *name;
+ const char *err;
+ int def;
+ union {
+ struct { /* range_option info */
+ int min;
+ int max;
+ } r;
+ struct { /* list_option info */
+ int nr;
+ const struct e1000_opt_list { int i; char *str; } *p;
+ } l;
+ } arg;
+};
+
+static int __devinit e1000_validate_option(unsigned int *value,
+ const struct e1000_option *opt,
+ struct e1000_adapter *adapter)
+{
+ if (*value == OPTION_UNSET) {
+ *value = opt->def;
+ return 0;
+ }
+
+ switch (opt->type) {
+ case enable_option:
+ switch (*value) {
+ case OPTION_ENABLED:
+ DPRINTK(PROBE, INFO, "%s Enabled\n", opt->name);
+ return 0;
+ case OPTION_DISABLED:
+ DPRINTK(PROBE, INFO, "%s Disabled\n", opt->name);
+ return 0;
+ }
+ break;
+ case range_option:
+ if (*value >= opt->arg.r.min && *value <= opt->arg.r.max) {
+ DPRINTK(PROBE, INFO,
+ "%s set to %i\n", opt->name, *value);
+ return 0;
+ }
+ break;
+ case list_option: {
+ int i;
+ const struct e1000_opt_list *ent;
+
+ for (i = 0; i < opt->arg.l.nr; i++) {
+ ent = &opt->arg.l.p[i];
+ if (*value == ent->i) {
+ if (ent->str[0] != '\0')
+ DPRINTK(PROBE, INFO, "%s\n", ent->str);
+ return 0;
+ }
+ }
+ }
+ break;
+ default:
+ BUG();
+ }
+
+ DPRINTK(PROBE, INFO, "Invalid %s value specified (%i) %s\n",
+ opt->name, *value, opt->err);
+ *value = opt->def;
+ return -1;
+}
+
+static void e1000_check_fiber_options(struct e1000_adapter *adapter);
+static void e1000_check_copper_options(struct e1000_adapter *adapter);
+
+/**
+ * e1000_check_options - Range Checking for Command Line Parameters
+ * @adapter: board private structure
+ *
+ * This routine checks all command line parameters for valid user
+ * input. If an invalid value is given, or if no user specified
+ * value exists, a default value is used. The final value is stored
+ * in a variable in the adapter structure.
+ **/
+
+void __devinit e1000_check_options(struct e1000_adapter *adapter)
+{
+ struct e1000_option opt;
+ int bd = adapter->bd_number;
+
+ if (bd >= E1000_MAX_NIC) {
+ DPRINTK(PROBE, NOTICE,
+ "Warning: no configuration for board #%i\n", bd);
+ DPRINTK(PROBE, NOTICE, "Using defaults for all values\n");
+ }
+
+ { /* Transmit Descriptor Count */
+ struct e1000_tx_ring *tx_ring = adapter->tx_ring;
+ int i;
+ e1000_mac_type mac_type = adapter->hw.mac_type;
+
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Transmit Descriptors",
+ .err = "using default of "
+ __MODULE_STRING(E1000_DEFAULT_TXD),
+ .def = E1000_DEFAULT_TXD,
+ .arg = { .r = {
+ .min = E1000_MIN_TXD,
+ .max = mac_type < e1000_82544 ? E1000_MAX_TXD : E1000_MAX_82544_TXD
+ }}
+ };
+
+ if (num_TxDescriptors > bd) {
+ tx_ring->count = TxDescriptors[bd];
+ e1000_validate_option(&tx_ring->count, &opt, adapter);
+ tx_ring->count = ALIGN(tx_ring->count,
+ REQ_TX_DESCRIPTOR_MULTIPLE);
+ } else {
+ tx_ring->count = opt.def;
+ }
+ for (i = 0; i < adapter->num_tx_queues; i++)
+ tx_ring[i].count = tx_ring->count;
+ }
+ { /* Receive Descriptor Count */
+ struct e1000_rx_ring *rx_ring = adapter->rx_ring;
+ int i;
+ e1000_mac_type mac_type = adapter->hw.mac_type;
+
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Receive Descriptors",
+ .err = "using default of "
+ __MODULE_STRING(E1000_DEFAULT_RXD),
+ .def = E1000_DEFAULT_RXD,
+ .arg = { .r = {
+ .min = E1000_MIN_RXD,
+ .max = mac_type < e1000_82544 ? E1000_MAX_RXD : E1000_MAX_82544_RXD
+ }}
+ };
+
+ if (num_RxDescriptors > bd) {
+ rx_ring->count = RxDescriptors[bd];
+ e1000_validate_option(&rx_ring->count, &opt, adapter);
+ rx_ring->count = ALIGN(rx_ring->count,
+ REQ_RX_DESCRIPTOR_MULTIPLE);
+ } else {
+ rx_ring->count = opt.def;
+ }
+ for (i = 0; i < adapter->num_rx_queues; i++)
+ rx_ring[i].count = rx_ring->count;
+ }
+ { /* Checksum Offload Enable/Disable */
+ opt = (struct e1000_option) {
+ .type = enable_option,
+ .name = "Checksum Offload",
+ .err = "defaulting to Enabled",
+ .def = OPTION_ENABLED
+ };
+
+ if (num_XsumRX > bd) {
+ unsigned int rx_csum = XsumRX[bd];
+ e1000_validate_option(&rx_csum, &opt, adapter);
+ adapter->rx_csum = rx_csum;
+ } else {
+ adapter->rx_csum = opt.def;
+ }
+ }
+ { /* Flow Control */
+
+ struct e1000_opt_list fc_list[] =
+ {{ E1000_FC_NONE, "Flow Control Disabled" },
+ { E1000_FC_RX_PAUSE,"Flow Control Receive Only" },
+ { E1000_FC_TX_PAUSE,"Flow Control Transmit Only" },
+ { E1000_FC_FULL, "Flow Control Enabled" },
+ { E1000_FC_DEFAULT, "Flow Control Hardware Default" }};
+
+ opt = (struct e1000_option) {
+ .type = list_option,
+ .name = "Flow Control",
+ .err = "reading default settings from EEPROM",
+ .def = E1000_FC_DEFAULT,
+ .arg = { .l = { .nr = ARRAY_SIZE(fc_list),
+ .p = fc_list }}
+ };
+
+ if (num_FlowControl > bd) {
+ unsigned int fc = FlowControl[bd];
+ e1000_validate_option(&fc, &opt, adapter);
+ adapter->hw.fc = adapter->hw.original_fc = fc;
+ } else {
+ adapter->hw.fc = adapter->hw.original_fc = opt.def;
+ }
+ }
+ { /* Transmit Interrupt Delay */
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Transmit Interrupt Delay",
+ .err = "using default of " __MODULE_STRING(DEFAULT_TIDV),
+ .def = DEFAULT_TIDV,
+ .arg = { .r = { .min = MIN_TXDELAY,
+ .max = MAX_TXDELAY }}
+ };
+
+ if (num_TxIntDelay > bd) {
+ adapter->tx_int_delay = TxIntDelay[bd];
+ e1000_validate_option(&adapter->tx_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->tx_int_delay = opt.def;
+ }
+ }
+ { /* Transmit Absolute Interrupt Delay */
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Transmit Absolute Interrupt Delay",
+ .err = "using default of " __MODULE_STRING(DEFAULT_TADV),
+ .def = DEFAULT_TADV,
+ .arg = { .r = { .min = MIN_TXABSDELAY,
+ .max = MAX_TXABSDELAY }}
+ };
+
+ if (num_TxAbsIntDelay > bd) {
+ adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
+ e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->tx_abs_int_delay = opt.def;
+ }
+ }
+ { /* Receive Interrupt Delay */
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Receive Interrupt Delay",
+ .err = "using default of " __MODULE_STRING(DEFAULT_RDTR),
+ .def = DEFAULT_RDTR,
+ .arg = { .r = { .min = MIN_RXDELAY,
+ .max = MAX_RXDELAY }}
+ };
+
+ if (num_RxIntDelay > bd) {
+ adapter->rx_int_delay = RxIntDelay[bd];
+ e1000_validate_option(&adapter->rx_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->rx_int_delay = opt.def;
+ }
+ }
+ { /* Receive Absolute Interrupt Delay */
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Receive Absolute Interrupt Delay",
+ .err = "using default of " __MODULE_STRING(DEFAULT_RADV),
+ .def = DEFAULT_RADV,
+ .arg = { .r = { .min = MIN_RXABSDELAY,
+ .max = MAX_RXABSDELAY }}
+ };
+
+ if (num_RxAbsIntDelay > bd) {
+ adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
+ e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->rx_abs_int_delay = opt.def;
+ }
+ }
+ { /* Interrupt Throttling Rate */
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Interrupt Throttling Rate (ints/sec)",
+ .err = "using default of " __MODULE_STRING(DEFAULT_ITR),
+ .def = DEFAULT_ITR,
+ .arg = { .r = { .min = MIN_ITR,
+ .max = MAX_ITR }}
+ };
+
+ if (num_InterruptThrottleRate > bd) {
+ adapter->itr = InterruptThrottleRate[bd];
+ switch (adapter->itr) {
+ case 0:
+ DPRINTK(PROBE, INFO, "%s turned off\n",
+ opt.name);
+ break;
+ case 1:
+ DPRINTK(PROBE, INFO, "%s set to dynamic mode\n",
+ opt.name);
+ adapter->itr_setting = adapter->itr;
+ adapter->itr = 20000;
+ break;
+ case 3:
+ DPRINTK(PROBE, INFO,
+ "%s set to dynamic conservative mode\n",
+ opt.name);
+ adapter->itr_setting = adapter->itr;
+ adapter->itr = 20000;
+ break;
+ default:
+ e1000_validate_option(&adapter->itr, &opt,
+ adapter);
+ /* save the setting, because the dynamic bits change itr */
+ /* clear the lower two bits because they are
+ * used as control */
+ adapter->itr_setting = adapter->itr & ~3;
+ break;
+ }
+ } else {
+ adapter->itr_setting = opt.def;
+ adapter->itr = 20000;
+ }
+ }
+ { /* Smart Power Down */
+ opt = (struct e1000_option) {
+ .type = enable_option,
+ .name = "PHY Smart Power Down",
+ .err = "defaulting to Disabled",
+ .def = OPTION_DISABLED
+ };
+
+ if (num_SmartPowerDownEnable > bd) {
+ unsigned int spd = SmartPowerDownEnable[bd];
+ e1000_validate_option(&spd, &opt, adapter);
+ adapter->smart_power_down = spd;
+ } else {
+ adapter->smart_power_down = opt.def;
+ }
+ }
+
+ switch (adapter->hw.media_type) {
+ case e1000_media_type_fiber:
+ case e1000_media_type_internal_serdes:
+ e1000_check_fiber_options(adapter);
+ break;
+ case e1000_media_type_copper:
+ e1000_check_copper_options(adapter);
+ break;
+ default:
+ BUG();
+ }
+}
+
+/**
+ * e1000_check_fiber_options - Range Checking for Link Options, Fiber Version
+ * @adapter: board private structure
+ *
+ * Handles speed and duplex options on fiber adapters
+ **/
+
+static void __devinit e1000_check_fiber_options(struct e1000_adapter *adapter)
+{
+ int bd = adapter->bd_number;
+ if (num_Speed > bd) {
+ DPRINTK(PROBE, INFO, "Speed not valid for fiber adapters, "
+ "parameter ignored\n");
+ }
+
+ if (num_Duplex > bd) {
+ DPRINTK(PROBE, INFO, "Duplex not valid for fiber adapters, "
+ "parameter ignored\n");
+ }
+
+ if ((num_AutoNeg > bd) && (AutoNeg[bd] != 0x20)) {
+ DPRINTK(PROBE, INFO, "AutoNeg other than 1000/Full is "
+ "not valid for fiber adapters, "
+ "parameter ignored\n");
+ }
+}
+
+/**
+ * e1000_check_copper_options - Range Checking for Link Options, Copper Version
+ * @adapter: board private structure
+ *
+ * Handles speed and duplex options on copper adapters
+ **/
+
+static void __devinit e1000_check_copper_options(struct e1000_adapter *adapter)
+{
+ struct e1000_option opt;
+ unsigned int speed, dplx, an;
+ int bd = adapter->bd_number;
+
+ { /* Speed */
+ static const struct e1000_opt_list speed_list[] = {
+ { 0, "" },
+ { SPEED_10, "" },
+ { SPEED_100, "" },
+ { SPEED_1000, "" }};
+
+ opt = (struct e1000_option) {
+ .type = list_option,
+ .name = "Speed",
+ .err = "parameter ignored",
+ .def = 0,
+ .arg = { .l = { .nr = ARRAY_SIZE(speed_list),
+ .p = speed_list }}
+ };
+
+ if (num_Speed > bd) {
+ speed = Speed[bd];
+ e1000_validate_option(&speed, &opt, adapter);
+ } else {
+ speed = opt.def;
+ }
+ }
+ { /* Duplex */
+ static const struct e1000_opt_list dplx_list[] = {
+ { 0, "" },
+ { HALF_DUPLEX, "" },
+ { FULL_DUPLEX, "" }};
+
+ opt = (struct e1000_option) {
+ .type = list_option,
+ .name = "Duplex",
+ .err = "parameter ignored",
+ .def = 0,
+ .arg = { .l = { .nr = ARRAY_SIZE(dplx_list),
+ .p = dplx_list }}
+ };
+
+ if (num_Duplex > bd) {
+ dplx = Duplex[bd];
+ e1000_validate_option(&dplx, &opt, adapter);
+ } else {
+ dplx = opt.def;
+ }
+ }
+
+ if ((num_AutoNeg > bd) && (speed != 0 || dplx != 0)) {
+ DPRINTK(PROBE, INFO,
+ "AutoNeg specified along with Speed or Duplex, "
+ "parameter ignored\n");
+ adapter->hw.autoneg_advertised = AUTONEG_ADV_DEFAULT;
+ } else { /* Autoneg */
+ static const struct e1000_opt_list an_list[] =
+ #define AA "AutoNeg advertising "
+ {{ 0x01, AA "10/HD" },
+ { 0x02, AA "10/FD" },
+ { 0x03, AA "10/FD, 10/HD" },
+ { 0x04, AA "100/HD" },
+ { 0x05, AA "100/HD, 10/HD" },
+ { 0x06, AA "100/HD, 10/FD" },
+ { 0x07, AA "100/HD, 10/FD, 10/HD" },
+ { 0x08, AA "100/FD" },
+ { 0x09, AA "100/FD, 10/HD" },
+ { 0x0a, AA "100/FD, 10/FD" },
+ { 0x0b, AA "100/FD, 10/FD, 10/HD" },
+ { 0x0c, AA "100/FD, 100/HD" },
+ { 0x0d, AA "100/FD, 100/HD, 10/HD" },
+ { 0x0e, AA "100/FD, 100/HD, 10/FD" },
+ { 0x0f, AA "100/FD, 100/HD, 10/FD, 10/HD" },
+ { 0x20, AA "1000/FD" },
+ { 0x21, AA "1000/FD, 10/HD" },
+ { 0x22, AA "1000/FD, 10/FD" },
+ { 0x23, AA "1000/FD, 10/FD, 10/HD" },
+ { 0x24, AA "1000/FD, 100/HD" },
+ { 0x25, AA "1000/FD, 100/HD, 10/HD" },
+ { 0x26, AA "1000/FD, 100/HD, 10/FD" },
+ { 0x27, AA "1000/FD, 100/HD, 10/FD, 10/HD" },
+ { 0x28, AA "1000/FD, 100/FD" },
+ { 0x29, AA "1000/FD, 100/FD, 10/HD" },
+ { 0x2a, AA "1000/FD, 100/FD, 10/FD" },
+ { 0x2b, AA "1000/FD, 100/FD, 10/FD, 10/HD" },
+ { 0x2c, AA "1000/FD, 100/FD, 100/HD" },
+ { 0x2d, AA "1000/FD, 100/FD, 100/HD, 10/HD" },
+ { 0x2e, AA "1000/FD, 100/FD, 100/HD, 10/FD" },
+ { 0x2f, AA "1000/FD, 100/FD, 100/HD, 10/FD, 10/HD" }};
+
+ opt = (struct e1000_option) {
+ .type = list_option,
+ .name = "AutoNeg",
+ .err = "parameter ignored",
+ .def = AUTONEG_ADV_DEFAULT,
+ .arg = { .l = { .nr = ARRAY_SIZE(an_list),
+ .p = an_list }}
+ };
+
+ if (num_AutoNeg > bd) {
+ an = AutoNeg[bd];
+ e1000_validate_option(&an, &opt, adapter);
+ } else {
+ an = opt.def;
+ }
+ adapter->hw.autoneg_advertised = an;
+ }
+
+ switch (speed + dplx) {
+ case 0:
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ if ((num_Speed > bd) && (speed != 0 || dplx != 0))
+ DPRINTK(PROBE, INFO,
+ "Speed and duplex autonegotiation enabled\n");
+ break;
+ case HALF_DUPLEX:
+ DPRINTK(PROBE, INFO, "Half Duplex specified without Speed\n");
+ DPRINTK(PROBE, INFO, "Using Autonegotiation at "
+ "Half Duplex only\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ adapter->hw.autoneg_advertised = ADVERTISE_10_HALF |
+ ADVERTISE_100_HALF;
+ break;
+ case FULL_DUPLEX:
+ DPRINTK(PROBE, INFO, "Full Duplex specified without Speed\n");
+ DPRINTK(PROBE, INFO, "Using Autonegotiation at "
+ "Full Duplex only\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ adapter->hw.autoneg_advertised = ADVERTISE_10_FULL |
+ ADVERTISE_100_FULL |
+ ADVERTISE_1000_FULL;
+ break;
+ case SPEED_10:
+ DPRINTK(PROBE, INFO, "10 Mbps Speed specified "
+ "without Duplex\n");
+ DPRINTK(PROBE, INFO, "Using Autonegotiation at 10 Mbps only\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ adapter->hw.autoneg_advertised = ADVERTISE_10_HALF |
+ ADVERTISE_10_FULL;
+ break;
+ case SPEED_10 + HALF_DUPLEX:
+ DPRINTK(PROBE, INFO, "Forcing to 10 Mbps Half Duplex\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 0;
+ adapter->hw.forced_speed_duplex = e1000_10_half;
+ adapter->hw.autoneg_advertised = 0;
+ break;
+ case SPEED_10 + FULL_DUPLEX:
+ DPRINTK(PROBE, INFO, "Forcing to 10 Mbps Full Duplex\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 0;
+ adapter->hw.forced_speed_duplex = e1000_10_full;
+ adapter->hw.autoneg_advertised = 0;
+ break;
+ case SPEED_100:
+ DPRINTK(PROBE, INFO, "100 Mbps Speed specified "
+ "without Duplex\n");
+ DPRINTK(PROBE, INFO, "Using Autonegotiation at "
+ "100 Mbps only\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ adapter->hw.autoneg_advertised = ADVERTISE_100_HALF |
+ ADVERTISE_100_FULL;
+ break;
+ case SPEED_100 + HALF_DUPLEX:
+ DPRINTK(PROBE, INFO, "Forcing to 100 Mbps Half Duplex\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 0;
+ adapter->hw.forced_speed_duplex = e1000_100_half;
+ adapter->hw.autoneg_advertised = 0;
+ break;
+ case SPEED_100 + FULL_DUPLEX:
+ DPRINTK(PROBE, INFO, "Forcing to 100 Mbps Full Duplex\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 0;
+ adapter->hw.forced_speed_duplex = e1000_100_full;
+ adapter->hw.autoneg_advertised = 0;
+ break;
+ case SPEED_1000:
+ DPRINTK(PROBE, INFO, "1000 Mbps Speed specified without "
+ "Duplex\n");
+ goto full_duplex_only;
+ case SPEED_1000 + HALF_DUPLEX:
+ DPRINTK(PROBE, INFO,
+ "Half Duplex is not supported at 1000 Mbps\n");
+ /* fall through */
+ case SPEED_1000 + FULL_DUPLEX:
+full_duplex_only:
+ DPRINTK(PROBE, INFO,
+ "Using Autonegotiation at 1000 Mbps Full Duplex only\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ adapter->hw.autoneg_advertised = ADVERTISE_1000_FULL;
+ break;
+ default:
+ BUG();
+ }
+
+ /* Speed, AutoNeg and MDI/MDI-X must all play nice */
+ if (e1000_validate_mdi_setting(&(adapter->hw)) < 0) {
+ DPRINTK(PROBE, INFO,
+ "Speed, AutoNeg and MDI-X specifications are "
+ "incompatible. Setting MDI-X to a compatible value.\n");
+ }
+}
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000/e1000_param-2.6.32-orig.c Thu Dec 15 13:21:32 2011 +0100
@@ -0,0 +1,770 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2006 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#include "e1000.h"
+
+/* This is the only thing that needs to be changed to adjust the
+ * maximum number of ports that the driver can manage.
+ */
+
+#define E1000_MAX_NIC 32
+
+#define OPTION_UNSET -1
+#define OPTION_DISABLED 0
+#define OPTION_ENABLED 1
+
+/* All parameters are treated the same, as an integer array of values.
+ * This macro just reduces the need to repeat the same declaration code
+ * over and over (plus this helps to avoid typo bugs).
+ */
+
+#define E1000_PARAM_INIT { [0 ... E1000_MAX_NIC] = OPTION_UNSET }
+#define E1000_PARAM(X, desc) \
+ static int __devinitdata X[E1000_MAX_NIC+1] = E1000_PARAM_INIT; \
+ static unsigned int num_##X; \
+ module_param_array_named(X, X, int, &num_##X, 0); \
+ MODULE_PARM_DESC(X, desc);
+
+/* Transmit Descriptor Count
+ *
+ * Valid Range: 80-256 for 82542 and 82543 gigabit ethernet controllers
+ * Valid Range: 80-4096 for 82544 and newer
+ *
+ * Default Value: 256
+ */
+E1000_PARAM(TxDescriptors, "Number of transmit descriptors");
+
+/* Receive Descriptor Count
+ *
+ * Valid Range: 80-256 for 82542 and 82543 gigabit ethernet controllers
+ * Valid Range: 80-4096 for 82544 and newer
+ *
+ * Default Value: 256
+ */
+E1000_PARAM(RxDescriptors, "Number of receive descriptors");
+
+/* User Specified Speed Override
+ *
+ * Valid Range: 0, 10, 100, 1000
+ * - 0 - auto-negotiate at all supported speeds
+ * - 10 - only link at 10 Mbps
+ * - 100 - only link at 100 Mbps
+ * - 1000 - only link at 1000 Mbps
+ *
+ * Default Value: 0
+ */
+E1000_PARAM(Speed, "Speed setting");
+
+/* User Specified Duplex Override
+ *
+ * Valid Range: 0-2
+ * - 0 - auto-negotiate for duplex
+ * - 1 - only link at half duplex
+ * - 2 - only link at full duplex
+ *
+ * Default Value: 0
+ */
+E1000_PARAM(Duplex, "Duplex setting");
+
+/* Auto-negotiation Advertisement Override
+ *
+ * Valid Range: 0x01-0x0F, 0x20-0x2F (copper); 0x20 (fiber)
+ *
+ * The AutoNeg value is a bit mask describing which speed and duplex
+ * combinations should be advertised during auto-negotiation.
+ * The supported speed and duplex modes are listed below
+ *
+ * Bit 7 6 5 4 3 2 1 0
+ * Speed (Mbps) N/A N/A 1000 N/A 100 100 10 10
+ * Duplex Full Full Half Full Half
+ *
+ * Default Value: 0x2F (copper); 0x20 (fiber)
+ */
+E1000_PARAM(AutoNeg, "Advertised auto-negotiation setting");
+#define AUTONEG_ADV_DEFAULT 0x2F
+#define AUTONEG_ADV_MASK 0x2F
+
+/* User Specified Flow Control Override
+ *
+ * Valid Range: 0-3
+ * - 0 - No Flow Control
+ * - 1 - Rx only, respond to PAUSE frames but do not generate them
+ * - 2 - Tx only, generate PAUSE frames but ignore them on receive
+ * - 3 - Full Flow Control Support
+ *
+ * Default Value: Read flow control settings from the EEPROM
+ */
+E1000_PARAM(FlowControl, "Flow Control setting");
+#define FLOW_CONTROL_DEFAULT FLOW_CONTROL_FULL
+
+/* XsumRX - Receive Checksum Offload Enable/Disable
+ *
+ * Valid Range: 0, 1
+ * - 0 - disables all checksum offload
+ * - 1 - enables receive IP/TCP/UDP checksum offload
+ * on 82543 and newer -based NICs
+ *
+ * Default Value: 1
+ */
+E1000_PARAM(XsumRX, "Disable or enable Receive Checksum offload");
+
+/* Transmit Interrupt Delay in units of 1.024 microseconds
+ * Tx interrupt delay needs to typically be set to something non zero
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(TxIntDelay, "Transmit Interrupt Delay");
+#define DEFAULT_TIDV 8
+#define MAX_TXDELAY 0xFFFF
+#define MIN_TXDELAY 0
+
+/* Transmit Absolute Interrupt Delay in units of 1.024 microseconds
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(TxAbsIntDelay, "Transmit Absolute Interrupt Delay");
+#define DEFAULT_TADV 32
+#define MAX_TXABSDELAY 0xFFFF
+#define MIN_TXABSDELAY 0
+
+/* Receive Interrupt Delay in units of 1.024 microseconds
+ * hardware will likely hang if you set this to anything but zero.
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(RxIntDelay, "Receive Interrupt Delay");
+#define DEFAULT_RDTR 0
+#define MAX_RXDELAY 0xFFFF
+#define MIN_RXDELAY 0
+
+/* Receive Absolute Interrupt Delay in units of 1.024 microseconds
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(RxAbsIntDelay, "Receive Absolute Interrupt Delay");
+#define DEFAULT_RADV 8
+#define MAX_RXABSDELAY 0xFFFF
+#define MIN_RXABSDELAY 0
+
+/* Interrupt Throttle Rate (interrupts/sec)
+ *
+ * Valid Range: 100-100000 (0=off, 1=dynamic, 3=dynamic conservative)
+ */
+E1000_PARAM(InterruptThrottleRate, "Interrupt Throttling Rate");
+#define DEFAULT_ITR 3
+#define MAX_ITR 100000
+#define MIN_ITR 100
+
+/* Enable Smart Power Down of the PHY
+ *
+ * Valid Range: 0, 1
+ *
+ * Default Value: 0 (disabled)
+ */
+E1000_PARAM(SmartPowerDownEnable, "Enable PHY smart power down");
+
+/* Enable Kumeran Lock Loss workaround
+ *
+ * Valid Range: 0, 1
+ *
+ * Default Value: 1 (enabled)
+ */
+E1000_PARAM(KumeranLockLoss, "Enable Kumeran lock loss workaround");
+
+struct e1000_option {
+ enum { enable_option, range_option, list_option } type;
+ const char *name;
+ const char *err;
+ int def;
+ union {
+ struct { /* range_option info */
+ int min;
+ int max;
+ } r;
+ struct { /* list_option info */
+ int nr;
+ const struct e1000_opt_list { int i; char *str; } *p;
+ } l;
+ } arg;
+};
+
+static int __devinit e1000_validate_option(unsigned int *value,
+ const struct e1000_option *opt,
+ struct e1000_adapter *adapter)
+{
+ if (*value == OPTION_UNSET) {
+ *value = opt->def;
+ return 0;
+ }
+
+ switch (opt->type) {
+ case enable_option:
+ switch (*value) {
+ case OPTION_ENABLED:
+ DPRINTK(PROBE, INFO, "%s Enabled\n", opt->name);
+ return 0;
+ case OPTION_DISABLED:
+ DPRINTK(PROBE, INFO, "%s Disabled\n", opt->name);
+ return 0;
+ }
+ break;
+ case range_option:
+ if (*value >= opt->arg.r.min && *value <= opt->arg.r.max) {
+ DPRINTK(PROBE, INFO,
+ "%s set to %i\n", opt->name, *value);
+ return 0;
+ }
+ break;
+ case list_option: {
+ int i;
+ const struct e1000_opt_list *ent;
+
+ for (i = 0; i < opt->arg.l.nr; i++) {
+ ent = &opt->arg.l.p[i];
+ if (*value == ent->i) {
+ if (ent->str[0] != '\0')
+ DPRINTK(PROBE, INFO, "%s\n", ent->str);
+ return 0;
+ }
+ }
+ }
+ break;
+ default:
+ BUG();
+ }
+
+ DPRINTK(PROBE, INFO, "Invalid %s value specified (%i) %s\n",
+ opt->name, *value, opt->err);
+ *value = opt->def;
+ return -1;
+}
+
+static void e1000_check_fiber_options(struct e1000_adapter *adapter);
+static void e1000_check_copper_options(struct e1000_adapter *adapter);
+
+/**
+ * e1000_check_options - Range Checking for Command Line Parameters
+ * @adapter: board private structure
+ *
+ * This routine checks all command line parameters for valid user
+ * input. If an invalid value is given, or if no user specified
+ * value exists, a default value is used. The final value is stored
+ * in a variable in the adapter structure.
+ **/
+
+void __devinit e1000_check_options(struct e1000_adapter *adapter)
+{
+ struct e1000_option opt;
+ int bd = adapter->bd_number;
+
+ if (bd >= E1000_MAX_NIC) {
+ DPRINTK(PROBE, NOTICE,
+ "Warning: no configuration for board #%i\n", bd);
+ DPRINTK(PROBE, NOTICE, "Using defaults for all values\n");
+ }
+
+ { /* Transmit Descriptor Count */
+ struct e1000_tx_ring *tx_ring = adapter->tx_ring;
+ int i;
+ e1000_mac_type mac_type = adapter->hw.mac_type;
+
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Transmit Descriptors",
+ .err = "using default of "
+ __MODULE_STRING(E1000_DEFAULT_TXD),
+ .def = E1000_DEFAULT_TXD,
+ .arg = { .r = {
+ .min = E1000_MIN_TXD,
+ .max = mac_type < e1000_82544 ? E1000_MAX_TXD : E1000_MAX_82544_TXD
+ }}
+ };
+
+ if (num_TxDescriptors > bd) {
+ tx_ring->count = TxDescriptors[bd];
+ e1000_validate_option(&tx_ring->count, &opt, adapter);
+ tx_ring->count = ALIGN(tx_ring->count,
+ REQ_TX_DESCRIPTOR_MULTIPLE);
+ } else {
+ tx_ring->count = opt.def;
+ }
+ for (i = 0; i < adapter->num_tx_queues; i++)
+ tx_ring[i].count = tx_ring->count;
+ }
+ { /* Receive Descriptor Count */
+ struct e1000_rx_ring *rx_ring = adapter->rx_ring;
+ int i;
+ e1000_mac_type mac_type = adapter->hw.mac_type;
+
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Receive Descriptors",
+ .err = "using default of "
+ __MODULE_STRING(E1000_DEFAULT_RXD),
+ .def = E1000_DEFAULT_RXD,
+ .arg = { .r = {
+ .min = E1000_MIN_RXD,
+ .max = mac_type < e1000_82544 ? E1000_MAX_RXD : E1000_MAX_82544_RXD
+ }}
+ };
+
+ if (num_RxDescriptors > bd) {
+ rx_ring->count = RxDescriptors[bd];
+ e1000_validate_option(&rx_ring->count, &opt, adapter);
+ rx_ring->count = ALIGN(rx_ring->count,
+ REQ_RX_DESCRIPTOR_MULTIPLE);
+ } else {
+ rx_ring->count = opt.def;
+ }
+ for (i = 0; i < adapter->num_rx_queues; i++)
+ rx_ring[i].count = rx_ring->count;
+ }
+ { /* Checksum Offload Enable/Disable */
+ opt = (struct e1000_option) {
+ .type = enable_option,
+ .name = "Checksum Offload",
+ .err = "defaulting to Enabled",
+ .def = OPTION_ENABLED
+ };
+
+ if (num_XsumRX > bd) {
+ unsigned int rx_csum = XsumRX[bd];
+ e1000_validate_option(&rx_csum, &opt, adapter);
+ adapter->rx_csum = rx_csum;
+ } else {
+ adapter->rx_csum = opt.def;
+ }
+ }
+ { /* Flow Control */
+
+ struct e1000_opt_list fc_list[] =
+ {{ E1000_FC_NONE, "Flow Control Disabled" },
+ { E1000_FC_RX_PAUSE,"Flow Control Receive Only" },
+ { E1000_FC_TX_PAUSE,"Flow Control Transmit Only" },
+ { E1000_FC_FULL, "Flow Control Enabled" },
+ { E1000_FC_DEFAULT, "Flow Control Hardware Default" }};
+
+ opt = (struct e1000_option) {
+ .type = list_option,
+ .name = "Flow Control",
+ .err = "reading default settings from EEPROM",
+ .def = E1000_FC_DEFAULT,
+ .arg = { .l = { .nr = ARRAY_SIZE(fc_list),
+ .p = fc_list }}
+ };
+
+ if (num_FlowControl > bd) {
+ unsigned int fc = FlowControl[bd];
+ e1000_validate_option(&fc, &opt, adapter);
+ adapter->hw.fc = adapter->hw.original_fc = fc;
+ } else {
+ adapter->hw.fc = adapter->hw.original_fc = opt.def;
+ }
+ }
+ { /* Transmit Interrupt Delay */
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Transmit Interrupt Delay",
+ .err = "using default of " __MODULE_STRING(DEFAULT_TIDV),
+ .def = DEFAULT_TIDV,
+ .arg = { .r = { .min = MIN_TXDELAY,
+ .max = MAX_TXDELAY }}
+ };
+
+ if (num_TxIntDelay > bd) {
+ adapter->tx_int_delay = TxIntDelay[bd];
+ e1000_validate_option(&adapter->tx_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->tx_int_delay = opt.def;
+ }
+ }
+ { /* Transmit Absolute Interrupt Delay */
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Transmit Absolute Interrupt Delay",
+ .err = "using default of " __MODULE_STRING(DEFAULT_TADV),
+ .def = DEFAULT_TADV,
+ .arg = { .r = { .min = MIN_TXABSDELAY,
+ .max = MAX_TXABSDELAY }}
+ };
+
+ if (num_TxAbsIntDelay > bd) {
+ adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
+ e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->tx_abs_int_delay = opt.def;
+ }
+ }
+ { /* Receive Interrupt Delay */
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Receive Interrupt Delay",
+ .err = "using default of " __MODULE_STRING(DEFAULT_RDTR),
+ .def = DEFAULT_RDTR,
+ .arg = { .r = { .min = MIN_RXDELAY,
+ .max = MAX_RXDELAY }}
+ };
+
+ if (num_RxIntDelay > bd) {
+ adapter->rx_int_delay = RxIntDelay[bd];
+ e1000_validate_option(&adapter->rx_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->rx_int_delay = opt.def;
+ }
+ }
+ { /* Receive Absolute Interrupt Delay */
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Receive Absolute Interrupt Delay",
+ .err = "using default of " __MODULE_STRING(DEFAULT_RADV),
+ .def = DEFAULT_RADV,
+ .arg = { .r = { .min = MIN_RXABSDELAY,
+ .max = MAX_RXABSDELAY }}
+ };
+
+ if (num_RxAbsIntDelay > bd) {
+ adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
+ e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->rx_abs_int_delay = opt.def;
+ }
+ }
+ { /* Interrupt Throttling Rate */
+ opt = (struct e1000_option) {
+ .type = range_option,
+ .name = "Interrupt Throttling Rate (ints/sec)",
+ .err = "using default of " __MODULE_STRING(DEFAULT_ITR),
+ .def = DEFAULT_ITR,
+ .arg = { .r = { .min = MIN_ITR,
+ .max = MAX_ITR }}
+ };
+
+ if (num_InterruptThrottleRate > bd) {
+ adapter->itr = InterruptThrottleRate[bd];
+ switch (adapter->itr) {
+ case 0:
+ DPRINTK(PROBE, INFO, "%s turned off\n",
+ opt.name);
+ break;
+ case 1:
+ DPRINTK(PROBE, INFO, "%s set to dynamic mode\n",
+ opt.name);
+ adapter->itr_setting = adapter->itr;
+ adapter->itr = 20000;
+ break;
+ case 3:
+ DPRINTK(PROBE, INFO,
+ "%s set to dynamic conservative mode\n",
+ opt.name);
+ adapter->itr_setting = adapter->itr;
+ adapter->itr = 20000;
+ break;
+ default:
+ e1000_validate_option(&adapter->itr, &opt,
+ adapter);
+ /* save the setting, because the dynamic bits change itr */
+ /* clear the lower two bits because they are
+ * used as control */
+ adapter->itr_setting = adapter->itr & ~3;
+ break;
+ }
+ } else {
+ adapter->itr_setting = opt.def;
+ adapter->itr = 20000;
+ }
+ }
+ { /* Smart Power Down */
+ opt = (struct e1000_option) {
+ .type = enable_option,
+ .name = "PHY Smart Power Down",
+ .err = "defaulting to Disabled",
+ .def = OPTION_DISABLED
+ };
+
+ if (num_SmartPowerDownEnable > bd) {
+ unsigned int spd = SmartPowerDownEnable[bd];
+ e1000_validate_option(&spd, &opt, adapter);
+ adapter->smart_power_down = spd;
+ } else {
+ adapter->smart_power_down = opt.def;
+ }
+ }
+
+ switch (adapter->hw.media_type) {
+ case e1000_media_type_fiber:
+ case e1000_media_type_internal_serdes:
+ e1000_check_fiber_options(adapter);
+ break;
+ case e1000_media_type_copper:
+ e1000_check_copper_options(adapter);
+ break;
+ default:
+ BUG();
+ }
+}
+
+/**
+ * e1000_check_fiber_options - Range Checking for Link Options, Fiber Version
+ * @adapter: board private structure
+ *
+ * Handles speed and duplex options on fiber adapters
+ **/
+
+static void __devinit e1000_check_fiber_options(struct e1000_adapter *adapter)
+{
+ int bd = adapter->bd_number;
+ if (num_Speed > bd) {
+ DPRINTK(PROBE, INFO, "Speed not valid for fiber adapters, "
+ "parameter ignored\n");
+ }
+
+ if (num_Duplex > bd) {
+ DPRINTK(PROBE, INFO, "Duplex not valid for fiber adapters, "
+ "parameter ignored\n");
+ }
+
+ if ((num_AutoNeg > bd) && (AutoNeg[bd] != 0x20)) {
+ DPRINTK(PROBE, INFO, "AutoNeg other than 1000/Full is "
+ "not valid for fiber adapters, "
+ "parameter ignored\n");
+ }
+}
+
+/**
+ * e1000_check_copper_options - Range Checking for Link Options, Copper Version
+ * @adapter: board private structure
+ *
+ * Handles speed and duplex options on copper adapters
+ **/
+
+static void __devinit e1000_check_copper_options(struct e1000_adapter *adapter)
+{
+ struct e1000_option opt;
+ unsigned int speed, dplx, an;
+ int bd = adapter->bd_number;
+
+ { /* Speed */
+ static const struct e1000_opt_list speed_list[] = {
+ { 0, "" },
+ { SPEED_10, "" },
+ { SPEED_100, "" },
+ { SPEED_1000, "" }};
+
+ opt = (struct e1000_option) {
+ .type = list_option,
+ .name = "Speed",
+ .err = "parameter ignored",
+ .def = 0,
+ .arg = { .l = { .nr = ARRAY_SIZE(speed_list),
+ .p = speed_list }}
+ };
+
+ if (num_Speed > bd) {
+ speed = Speed[bd];
+ e1000_validate_option(&speed, &opt, adapter);
+ } else {
+ speed = opt.def;
+ }
+ }
+ { /* Duplex */
+ static const struct e1000_opt_list dplx_list[] = {
+ { 0, "" },
+ { HALF_DUPLEX, "" },
+ { FULL_DUPLEX, "" }};
+
+ opt = (struct e1000_option) {
+ .type = list_option,
+ .name = "Duplex",
+ .err = "parameter ignored",
+ .def = 0,
+ .arg = { .l = { .nr = ARRAY_SIZE(dplx_list),
+ .p = dplx_list }}
+ };
+
+ if (num_Duplex > bd) {
+ dplx = Duplex[bd];
+ e1000_validate_option(&dplx, &opt, adapter);
+ } else {
+ dplx = opt.def;
+ }
+ }
+
+ if ((num_AutoNeg > bd) && (speed != 0 || dplx != 0)) {
+ DPRINTK(PROBE, INFO,
+ "AutoNeg specified along with Speed or Duplex, "
+ "parameter ignored\n");
+ adapter->hw.autoneg_advertised = AUTONEG_ADV_DEFAULT;
+ } else { /* Autoneg */
+ static const struct e1000_opt_list an_list[] =
+ #define AA "AutoNeg advertising "
+ {{ 0x01, AA "10/HD" },
+ { 0x02, AA "10/FD" },
+ { 0x03, AA "10/FD, 10/HD" },
+ { 0x04, AA "100/HD" },
+ { 0x05, AA "100/HD, 10/HD" },
+ { 0x06, AA "100/HD, 10/FD" },
+ { 0x07, AA "100/HD, 10/FD, 10/HD" },
+ { 0x08, AA "100/FD" },
+ { 0x09, AA "100/FD, 10/HD" },
+ { 0x0a, AA "100/FD, 10/FD" },
+ { 0x0b, AA "100/FD, 10/FD, 10/HD" },
+ { 0x0c, AA "100/FD, 100/HD" },
+ { 0x0d, AA "100/FD, 100/HD, 10/HD" },
+ { 0x0e, AA "100/FD, 100/HD, 10/FD" },
+ { 0x0f, AA "100/FD, 100/HD, 10/FD, 10/HD" },
+ { 0x20, AA "1000/FD" },
+ { 0x21, AA "1000/FD, 10/HD" },
+ { 0x22, AA "1000/FD, 10/FD" },
+ { 0x23, AA "1000/FD, 10/FD, 10/HD" },
+ { 0x24, AA "1000/FD, 100/HD" },
+ { 0x25, AA "1000/FD, 100/HD, 10/HD" },
+ { 0x26, AA "1000/FD, 100/HD, 10/FD" },
+ { 0x27, AA "1000/FD, 100/HD, 10/FD, 10/HD" },
+ { 0x28, AA "1000/FD, 100/FD" },
+ { 0x29, AA "1000/FD, 100/FD, 10/HD" },
+ { 0x2a, AA "1000/FD, 100/FD, 10/FD" },
+ { 0x2b, AA "1000/FD, 100/FD, 10/FD, 10/HD" },
+ { 0x2c, AA "1000/FD, 100/FD, 100/HD" },
+ { 0x2d, AA "1000/FD, 100/FD, 100/HD, 10/HD" },
+ { 0x2e, AA "1000/FD, 100/FD, 100/HD, 10/FD" },
+ { 0x2f, AA "1000/FD, 100/FD, 100/HD, 10/FD, 10/HD" }};
+
+ opt = (struct e1000_option) {
+ .type = list_option,
+ .name = "AutoNeg",
+ .err = "parameter ignored",
+ .def = AUTONEG_ADV_DEFAULT,
+ .arg = { .l = { .nr = ARRAY_SIZE(an_list),
+ .p = an_list }}
+ };
+
+ if (num_AutoNeg > bd) {
+ an = AutoNeg[bd];
+ e1000_validate_option(&an, &opt, adapter);
+ } else {
+ an = opt.def;
+ }
+ adapter->hw.autoneg_advertised = an;
+ }
+
+ switch (speed + dplx) {
+ case 0:
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ if ((num_Speed > bd) && (speed != 0 || dplx != 0))
+ DPRINTK(PROBE, INFO,
+ "Speed and duplex autonegotiation enabled\n");
+ break;
+ case HALF_DUPLEX:
+ DPRINTK(PROBE, INFO, "Half Duplex specified without Speed\n");
+ DPRINTK(PROBE, INFO, "Using Autonegotiation at "
+ "Half Duplex only\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ adapter->hw.autoneg_advertised = ADVERTISE_10_HALF |
+ ADVERTISE_100_HALF;
+ break;
+ case FULL_DUPLEX:
+ DPRINTK(PROBE, INFO, "Full Duplex specified without Speed\n");
+ DPRINTK(PROBE, INFO, "Using Autonegotiation at "
+ "Full Duplex only\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ adapter->hw.autoneg_advertised = ADVERTISE_10_FULL |
+ ADVERTISE_100_FULL |
+ ADVERTISE_1000_FULL;
+ break;
+ case SPEED_10:
+ DPRINTK(PROBE, INFO, "10 Mbps Speed specified "
+ "without Duplex\n");
+ DPRINTK(PROBE, INFO, "Using Autonegotiation at 10 Mbps only\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ adapter->hw.autoneg_advertised = ADVERTISE_10_HALF |
+ ADVERTISE_10_FULL;
+ break;
+ case SPEED_10 + HALF_DUPLEX:
+ DPRINTK(PROBE, INFO, "Forcing to 10 Mbps Half Duplex\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 0;
+ adapter->hw.forced_speed_duplex = e1000_10_half;
+ adapter->hw.autoneg_advertised = 0;
+ break;
+ case SPEED_10 + FULL_DUPLEX:
+ DPRINTK(PROBE, INFO, "Forcing to 10 Mbps Full Duplex\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 0;
+ adapter->hw.forced_speed_duplex = e1000_10_full;
+ adapter->hw.autoneg_advertised = 0;
+ break;
+ case SPEED_100:
+ DPRINTK(PROBE, INFO, "100 Mbps Speed specified "
+ "without Duplex\n");
+ DPRINTK(PROBE, INFO, "Using Autonegotiation at "
+ "100 Mbps only\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ adapter->hw.autoneg_advertised = ADVERTISE_100_HALF |
+ ADVERTISE_100_FULL;
+ break;
+ case SPEED_100 + HALF_DUPLEX:
+ DPRINTK(PROBE, INFO, "Forcing to 100 Mbps Half Duplex\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 0;
+ adapter->hw.forced_speed_duplex = e1000_100_half;
+ adapter->hw.autoneg_advertised = 0;
+ break;
+ case SPEED_100 + FULL_DUPLEX:
+ DPRINTK(PROBE, INFO, "Forcing to 100 Mbps Full Duplex\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 0;
+ adapter->hw.forced_speed_duplex = e1000_100_full;
+ adapter->hw.autoneg_advertised = 0;
+ break;
+ case SPEED_1000:
+ DPRINTK(PROBE, INFO, "1000 Mbps Speed specified without "
+ "Duplex\n");
+ goto full_duplex_only;
+ case SPEED_1000 + HALF_DUPLEX:
+ DPRINTK(PROBE, INFO,
+ "Half Duplex is not supported at 1000 Mbps\n");
+ /* fall through */
+ case SPEED_1000 + FULL_DUPLEX:
+full_duplex_only:
+ DPRINTK(PROBE, INFO,
+ "Using Autonegotiation at 1000 Mbps Full Duplex only\n");
+ adapter->hw.autoneg = adapter->fc_autoneg = 1;
+ adapter->hw.autoneg_advertised = ADVERTISE_1000_FULL;
+ break;
+ default:
+ BUG();
+ }
+
+ /* Speed, AutoNeg and MDI/MDI-X must all play nice */
+ if (e1000_validate_mdi_setting(&(adapter->hw)) < 0) {
+ DPRINTK(PROBE, INFO,
+ "Speed, AutoNeg and MDI-X specifications are "
+ "incompatible. Setting MDI-X to a compatible value.\n");
+ }
+}
+