Implemented EoE Set IP parameter request via command-line tool.
/* Intel PRO/1000 Linux driver
* Copyright(c) 1999 - 2014 Intel Corporation.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2, as published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* The full GNU General Public License is included in this distribution in
* the file called "COPYING".
*
* Contact Information:
* Linux NICS <linux.nics@intel.com>
* e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
* Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
*/
#ifndef _E1000E_80003ES2LAN_H_
#define _E1000E_80003ES2LAN_H_
#define E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL 0x00
#define E1000_KMRNCTRLSTA_OFFSET_INB_CTRL 0x02
#define E1000_KMRNCTRLSTA_OFFSET_HD_CTRL 0x10
#define E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE 0x1F
#define E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS 0x0008
#define E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS 0x0800
#define E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING 0x0010
#define E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT 0x0004
#define E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT 0x0000
#define E1000_KMRNCTRLSTA_OPMODE_E_IDLE 0x2000
#define E1000_KMRNCTRLSTA_OPMODE_MASK 0x000C
#define E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO 0x0004
#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gig Carry Extend Padding */
#define DEFAULT_TCTL_EXT_GCEX_80003ES2LAN 0x00010000
#define DEFAULT_TIPG_IPGT_1000_80003ES2LAN 0x8
#define DEFAULT_TIPG_IPGT_10_100_80003ES2LAN 0x9
/* GG82563 PHY Specific Status Register (Page 0, Register 16 */
#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Reversal Dis */
#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060
#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI */
#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX */
#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Auto crossover */
/* PHY Specific Control Register 2 (Page 0, Register 26) */
#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000 /* 1=Reverse Auto-Neg */
/* MAC Specific Control Register (Page 2, Register 21) */
/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */
#define GG82563_MSCR_TX_CLK_MASK 0x0007
#define GG82563_MSCR_TX_CLK_10MBPS_2_5 0x0004
#define GG82563_MSCR_TX_CLK_100MBPS_25 0x0005
#define GG82563_MSCR_TX_CLK_1000MBPS_25 0x0007
#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */
/* DSP Distance Register (Page 5, Register 26)
* 0 = <50M
* 1 = 50-80M
* 2 = 80-100M
* 3 = 110-140M
* 4 = >140M
*/
#define GG82563_DSPD_CABLE_LENGTH 0x0007
/* Kumeran Mode Control Register (Page 193, Register 16) */
#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800
/* Max number of times Kumeran read/write should be validated */
#define GG82563_MAX_KMRN_RETRY 0x5
/* Power Management Control Register (Page 193, Register 20) */
/* 1=Enable SERDES Electrical Idle */
#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001
/* In-Band Control Register (Page 194, Register 18) */
#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding */
#endif