--- a/NEWS	Fri Oct 28 13:07:54 2011 +0200
+++ b/NEWS	Fri Oct 28 17:09:02 2011 +0200
@@ -8,7 +8,7 @@
 
 Changes since 1.5:
 
-* Added e1000e driver for 2.6.34 (thanks to Siwei Zhuang), 2.6.37.
+* Added e1000e driver for 2.3.32, 2.6.34 (thanks to Siwei Zhuang), 2.6.37.
 
 Changes in 1.5:
 

--- a/devices/8139too-2.6.32-ethercat.c	Fri Oct 28 13:07:54 2011 +0200
+++ b/devices/8139too-2.6.32-ethercat.c	Fri Oct 28 17:09:02 2011 +0200
@@ -1779,7 +1779,7 @@
 	void __iomem *ioaddr = tp->mmio_addr;
 	unsigned int entry;
 	unsigned int len = skb->len;
-	unsigned long flags;
+	unsigned long flags = 0;
 
 	/* Calculate the next Tx descriptor entry. */
 	entry = tp->cur_tx % NUM_TX_DESC;

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000e/82571-2.6.32-ethercat.c	Fri Oct 28 17:09:02 2011 +0200
@@ -0,0 +1,1829 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2008 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/*
+ * 82571EB Gigabit Ethernet Controller
+ * 82571EB Gigabit Ethernet Controller (Copper)
+ * 82571EB Gigabit Ethernet Controller (Fiber)
+ * 82571EB Dual Port Gigabit Mezzanine Adapter
+ * 82571EB Quad Port Gigabit Mezzanine Adapter
+ * 82571PT Gigabit PT Quad Port Server ExpressModule
+ * 82572EI Gigabit Ethernet Controller (Copper)
+ * 82572EI Gigabit Ethernet Controller (Fiber)
+ * 82572EI Gigabit Ethernet Controller
+ * 82573V Gigabit Ethernet Controller (Copper)
+ * 82573E Gigabit Ethernet Controller (Copper)
+ * 82573L Gigabit Ethernet Controller
+ * 82574L Gigabit Network Connection
+ * 82583V Gigabit Network Connection
+ */
+
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+
+#include "e1000-2.6.32-ethercat.h"
+
+#define ID_LED_RESERVED_F746 0xF746
+#define ID_LED_DEFAULT_82573 ((ID_LED_DEF1_DEF2 << 12) | \
+			      (ID_LED_OFF1_ON2  <<  8) | \
+			      (ID_LED_DEF1_DEF2 <<  4) | \
+			      (ID_LED_DEF1_DEF2))
+
+#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
+
+#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */
+
+static s32 e1000_get_phy_id_82571(struct e1000_hw *hw);
+static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw);
+static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw);
+static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw);
+static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
+				      u16 words, u16 *data);
+static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw);
+static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw);
+static s32 e1000_setup_link_82571(struct e1000_hw *hw);
+static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw);
+static bool e1000_check_mng_mode_82574(struct e1000_hw *hw);
+static s32 e1000_led_on_82574(struct e1000_hw *hw);
+static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw);
+
+/**
+ *  e1000_init_phy_params_82571 - Init PHY func ptrs.
+ *  @hw: pointer to the HW structure
+ *
+ *  This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_phy_params_82571(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+
+	if (hw->phy.media_type != e1000_media_type_copper) {
+		phy->type = e1000_phy_none;
+		return 0;
+	}
+
+	phy->addr			 = 1;
+	phy->autoneg_mask		 = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+	phy->reset_delay_us		 = 100;
+
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		phy->type		 = e1000_phy_igp_2;
+		break;
+	case e1000_82573:
+		phy->type		 = e1000_phy_m88;
+		break;
+	case e1000_82574:
+	case e1000_82583:
+		phy->type		 = e1000_phy_bm;
+		break;
+	default:
+		return -E1000_ERR_PHY;
+		break;
+	}
+
+	/* This can only be done after all function pointers are setup. */
+	ret_val = e1000_get_phy_id_82571(hw);
+
+	/* Verify phy id */
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		if (phy->id != IGP01E1000_I_PHY_ID)
+			return -E1000_ERR_PHY;
+		break;
+	case e1000_82573:
+		if (phy->id != M88E1111_I_PHY_ID)
+			return -E1000_ERR_PHY;
+		break;
+	case e1000_82574:
+	case e1000_82583:
+		if (phy->id != BME1000_E_PHY_ID_R2)
+			return -E1000_ERR_PHY;
+		break;
+	default:
+		return -E1000_ERR_PHY;
+		break;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_init_nvm_params_82571 - Init NVM func ptrs.
+ *  @hw: pointer to the HW structure
+ *
+ *  This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_nvm_params_82571(struct e1000_hw *hw)
+{
+	struct e1000_nvm_info *nvm = &hw->nvm;
+	u32 eecd = er32(EECD);
+	u16 size;
+
+	nvm->opcode_bits = 8;
+	nvm->delay_usec = 1;
+	switch (nvm->override) {
+	case e1000_nvm_override_spi_large:
+		nvm->page_size = 32;
+		nvm->address_bits = 16;
+		break;
+	case e1000_nvm_override_spi_small:
+		nvm->page_size = 8;
+		nvm->address_bits = 8;
+		break;
+	default:
+		nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
+		nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
+		break;
+	}
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		if (((eecd >> 15) & 0x3) == 0x3) {
+			nvm->type = e1000_nvm_flash_hw;
+			nvm->word_size = 2048;
+			/*
+			 * Autonomous Flash update bit must be cleared due
+			 * to Flash update issue.
+			 */
+			eecd &= ~E1000_EECD_AUPDEN;
+			ew32(EECD, eecd);
+			break;
+		}
+		/* Fall Through */
+	default:
+		nvm->type = e1000_nvm_eeprom_spi;
+		size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
+				  E1000_EECD_SIZE_EX_SHIFT);
+		/*
+		 * Added to a constant, "size" becomes the left-shift value
+		 * for setting word_size.
+		 */
+		size += NVM_WORD_SIZE_BASE_SHIFT;
+
+		/* EEPROM access above 16k is unsupported */
+		if (size > 14)
+			size = 14;
+		nvm->word_size	= 1 << size;
+		break;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_init_mac_params_82571 - Init MAC func ptrs.
+ *  @hw: pointer to the HW structure
+ *
+ *  This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_mac_params_82571(struct e1000_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	struct e1000_mac_info *mac = &hw->mac;
+	struct e1000_mac_operations *func = &mac->ops;
+	u32 swsm = 0;
+	u32 swsm2 = 0;
+	bool force_clear_smbi = false;
+
+	/* Set media type */
+	switch (adapter->pdev->device) {
+	case E1000_DEV_ID_82571EB_FIBER:
+	case E1000_DEV_ID_82572EI_FIBER:
+	case E1000_DEV_ID_82571EB_QUAD_FIBER:
+		hw->phy.media_type = e1000_media_type_fiber;
+		break;
+	case E1000_DEV_ID_82571EB_SERDES:
+	case E1000_DEV_ID_82572EI_SERDES:
+	case E1000_DEV_ID_82571EB_SERDES_DUAL:
+	case E1000_DEV_ID_82571EB_SERDES_QUAD:
+		hw->phy.media_type = e1000_media_type_internal_serdes;
+		break;
+	default:
+		hw->phy.media_type = e1000_media_type_copper;
+		break;
+	}
+
+	/* Set mta register count */
+	mac->mta_reg_count = 128;
+	/* Set rar entry count */
+	mac->rar_entry_count = E1000_RAR_ENTRIES;
+	/* Set if manageability features are enabled. */
+	mac->arc_subsystem_valid = (er32(FWSM) & E1000_FWSM_MODE_MASK) ? 1 : 0;
+
+	/* check for link */
+	switch (hw->phy.media_type) {
+	case e1000_media_type_copper:
+		func->setup_physical_interface = e1000_setup_copper_link_82571;
+		func->check_for_link = e1000e_check_for_copper_link;
+		func->get_link_up_info = e1000e_get_speed_and_duplex_copper;
+		break;
+	case e1000_media_type_fiber:
+		func->setup_physical_interface =
+			e1000_setup_fiber_serdes_link_82571;
+		func->check_for_link = e1000e_check_for_fiber_link;
+		func->get_link_up_info =
+			e1000e_get_speed_and_duplex_fiber_serdes;
+		break;
+	case e1000_media_type_internal_serdes:
+		func->setup_physical_interface =
+			e1000_setup_fiber_serdes_link_82571;
+		func->check_for_link = e1000_check_for_serdes_link_82571;
+		func->get_link_up_info =
+			e1000e_get_speed_and_duplex_fiber_serdes;
+		break;
+	default:
+		return -E1000_ERR_CONFIG;
+		break;
+	}
+
+	switch (hw->mac.type) {
+	case e1000_82574:
+	case e1000_82583:
+		func->check_mng_mode = e1000_check_mng_mode_82574;
+		func->led_on = e1000_led_on_82574;
+		break;
+	default:
+		func->check_mng_mode = e1000e_check_mng_mode_generic;
+		func->led_on = e1000e_led_on_generic;
+		break;
+	}
+
+	/*
+	 * Ensure that the inter-port SWSM.SMBI lock bit is clear before
+	 * first NVM or PHY acess. This should be done for single-port
+	 * devices, and for one port only on dual-port devices so that
+	 * for those devices we can still use the SMBI lock to synchronize
+	 * inter-port accesses to the PHY & NVM.
+	 */
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		swsm2 = er32(SWSM2);
+
+		if (!(swsm2 & E1000_SWSM2_LOCK)) {
+			/* Only do this for the first interface on this card */
+			ew32(SWSM2,
+			    swsm2 | E1000_SWSM2_LOCK);
+			force_clear_smbi = true;
+		} else
+			force_clear_smbi = false;
+		break;
+	default:
+		force_clear_smbi = true;
+		break;
+	}
+
+	if (force_clear_smbi) {
+		/* Make sure SWSM.SMBI is clear */
+		swsm = er32(SWSM);
+		if (swsm & E1000_SWSM_SMBI) {
+			/* This bit should not be set on a first interface, and
+			 * indicates that the bootagent or EFI code has
+			 * improperly left this bit enabled
+			 */
+			hw_dbg(hw, "Please update your 82571 Bootagent\n");
+		}
+		ew32(SWSM, swsm & ~E1000_SWSM_SMBI);
+	}
+
+	/*
+	 * Initialze device specific counter of SMBI acquisition
+	 * timeouts.
+	 */
+	 hw->dev_spec.e82571.smb_counter = 0;
+
+	return 0;
+}
+
+static s32 e1000_get_variants_82571(struct e1000_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	static int global_quad_port_a; /* global port a indication */
+	struct pci_dev *pdev = adapter->pdev;
+	u16 eeprom_data = 0;
+	int is_port_b = er32(STATUS) & E1000_STATUS_FUNC_1;
+	s32 rc;
+
+	rc = e1000_init_mac_params_82571(adapter);
+	if (rc)
+		return rc;
+
+	rc = e1000_init_nvm_params_82571(hw);
+	if (rc)
+		return rc;
+
+	rc = e1000_init_phy_params_82571(hw);
+	if (rc)
+		return rc;
+
+	/* tag quad port adapters first, it's used below */
+	switch (pdev->device) {
+	case E1000_DEV_ID_82571EB_QUAD_COPPER:
+	case E1000_DEV_ID_82571EB_QUAD_FIBER:
+	case E1000_DEV_ID_82571EB_QUAD_COPPER_LP:
+	case E1000_DEV_ID_82571PT_QUAD_COPPER:
+		adapter->flags |= FLAG_IS_QUAD_PORT;
+		/* mark the first port */
+		if (global_quad_port_a == 0)
+			adapter->flags |= FLAG_IS_QUAD_PORT_A;
+		/* Reset for multiple quad port adapters */
+		global_quad_port_a++;
+		if (global_quad_port_a == 4)
+			global_quad_port_a = 0;
+		break;
+	default:
+		break;
+	}
+
+	switch (adapter->hw.mac.type) {
+	case e1000_82571:
+		/* these dual ports don't have WoL on port B at all */
+		if (((pdev->device == E1000_DEV_ID_82571EB_FIBER) ||
+		     (pdev->device == E1000_DEV_ID_82571EB_SERDES) ||
+		     (pdev->device == E1000_DEV_ID_82571EB_COPPER)) &&
+		    (is_port_b))
+			adapter->flags &= ~FLAG_HAS_WOL;
+		/* quad ports only support WoL on port A */
+		if (adapter->flags & FLAG_IS_QUAD_PORT &&
+		    (!(adapter->flags & FLAG_IS_QUAD_PORT_A)))
+			adapter->flags &= ~FLAG_HAS_WOL;
+		/* Does not support WoL on any port */
+		if (pdev->device == E1000_DEV_ID_82571EB_SERDES_QUAD)
+			adapter->flags &= ~FLAG_HAS_WOL;
+		break;
+
+	case e1000_82573:
+		if (pdev->device == E1000_DEV_ID_82573L) {
+			if (e1000_read_nvm(&adapter->hw, NVM_INIT_3GIO_3, 1,
+				       &eeprom_data) < 0)
+				break;
+			if (!(eeprom_data & NVM_WORD1A_ASPM_MASK)) {
+				adapter->flags |= FLAG_HAS_JUMBO_FRAMES;
+				adapter->max_hw_frame_size = DEFAULT_JUMBO;
+			}
+		}
+		break;
+	default:
+		break;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_get_phy_id_82571 - Retrieve the PHY ID and revision
+ *  @hw: pointer to the HW structure
+ *
+ *  Reads the PHY registers and stores the PHY ID and possibly the PHY
+ *  revision in the hardware structure.
+ **/
+static s32 e1000_get_phy_id_82571(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 phy_id = 0;
+
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		/*
+		 * The 82571 firmware may still be configuring the PHY.
+		 * In this case, we cannot access the PHY until the
+		 * configuration is done.  So we explicitly set the
+		 * PHY ID.
+		 */
+		phy->id = IGP01E1000_I_PHY_ID;
+		break;
+	case e1000_82573:
+		return e1000e_get_phy_id(hw);
+		break;
+	case e1000_82574:
+	case e1000_82583:
+		ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+		if (ret_val)
+			return ret_val;
+
+		phy->id = (u32)(phy_id << 16);
+		udelay(20);
+		ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+		if (ret_val)
+			return ret_val;
+
+		phy->id |= (u32)(phy_id);
+		phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+		break;
+	default:
+		return -E1000_ERR_PHY;
+		break;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_get_hw_semaphore_82571 - Acquire hardware semaphore
+ *  @hw: pointer to the HW structure
+ *
+ *  Acquire the HW semaphore to access the PHY or NVM
+ **/
+static s32 e1000_get_hw_semaphore_82571(struct e1000_hw *hw)
+{
+	u32 swsm;
+	s32 sw_timeout = hw->nvm.word_size + 1;
+	s32 fw_timeout = hw->nvm.word_size + 1;
+	s32 i = 0;
+
+	/*
+	 * If we have timedout 3 times on trying to acquire
+	 * the inter-port SMBI semaphore, there is old code
+	 * operating on the other port, and it is not
+	 * releasing SMBI. Modify the number of times that
+	 * we try for the semaphore to interwork with this
+	 * older code.
+	 */
+	if (hw->dev_spec.e82571.smb_counter > 2)
+		sw_timeout = 1;
+
+	/* Get the SW semaphore */
+	while (i < sw_timeout) {
+		swsm = er32(SWSM);
+		if (!(swsm & E1000_SWSM_SMBI))
+			break;
+
+		udelay(50);
+		i++;
+	}
+
+	if (i == sw_timeout) {
+		hw_dbg(hw, "Driver can't access device - SMBI bit is set.\n");
+		hw->dev_spec.e82571.smb_counter++;
+	}
+	/* Get the FW semaphore. */
+	for (i = 0; i < fw_timeout; i++) {
+		swsm = er32(SWSM);
+		ew32(SWSM, swsm | E1000_SWSM_SWESMBI);
+
+		/* Semaphore acquired if bit latched */
+		if (er32(SWSM) & E1000_SWSM_SWESMBI)
+			break;
+
+		udelay(50);
+	}
+
+	if (i == fw_timeout) {
+		/* Release semaphores */
+		e1000_put_hw_semaphore_82571(hw);
+		hw_dbg(hw, "Driver can't access the NVM\n");
+		return -E1000_ERR_NVM;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_put_hw_semaphore_82571 - Release hardware semaphore
+ *  @hw: pointer to the HW structure
+ *
+ *  Release hardware semaphore used to access the PHY or NVM
+ **/
+static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw)
+{
+	u32 swsm;
+
+	swsm = er32(SWSM);
+	swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
+	ew32(SWSM, swsm);
+}
+
+/**
+ *  e1000_acquire_nvm_82571 - Request for access to the EEPROM
+ *  @hw: pointer to the HW structure
+ *
+ *  To gain access to the EEPROM, first we must obtain a hardware semaphore.
+ *  Then for non-82573 hardware, set the EEPROM access request bit and wait
+ *  for EEPROM access grant bit.  If the access grant bit is not set, release
+ *  hardware semaphore.
+ **/
+static s32 e1000_acquire_nvm_82571(struct e1000_hw *hw)
+{
+	s32 ret_val;
+
+	ret_val = e1000_get_hw_semaphore_82571(hw);
+	if (ret_val)
+		return ret_val;
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		break;
+	default:
+		ret_val = e1000e_acquire_nvm(hw);
+		break;
+	}
+
+	if (ret_val)
+		e1000_put_hw_semaphore_82571(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_release_nvm_82571 - Release exclusive access to EEPROM
+ *  @hw: pointer to the HW structure
+ *
+ *  Stop any current commands to the EEPROM and clear the EEPROM request bit.
+ **/
+static void e1000_release_nvm_82571(struct e1000_hw *hw)
+{
+	e1000e_release_nvm(hw);
+	e1000_put_hw_semaphore_82571(hw);
+}
+
+/**
+ *  e1000_write_nvm_82571 - Write to EEPROM using appropriate interface
+ *  @hw: pointer to the HW structure
+ *  @offset: offset within the EEPROM to be written to
+ *  @words: number of words to write
+ *  @data: 16 bit word(s) to be written to the EEPROM
+ *
+ *  For non-82573 silicon, write data to EEPROM at offset using SPI interface.
+ *
+ *  If e1000e_update_nvm_checksum is not called after this function, the
+ *  EEPROM will most likely contain an invalid checksum.
+ **/
+static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words,
+				 u16 *data)
+{
+	s32 ret_val;
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		ret_val = e1000_write_nvm_eewr_82571(hw, offset, words, data);
+		break;
+	case e1000_82571:
+	case e1000_82572:
+		ret_val = e1000e_write_nvm_spi(hw, offset, words, data);
+		break;
+	default:
+		ret_val = -E1000_ERR_NVM;
+		break;
+	}
+
+	return ret_val;
+}
+
+/**
+ *  e1000_update_nvm_checksum_82571 - Update EEPROM checksum
+ *  @hw: pointer to the HW structure
+ *
+ *  Updates the EEPROM checksum by reading/adding each word of the EEPROM
+ *  up to the checksum.  Then calculates the EEPROM checksum and writes the
+ *  value to the EEPROM.
+ **/
+static s32 e1000_update_nvm_checksum_82571(struct e1000_hw *hw)
+{
+	u32 eecd;
+	s32 ret_val;
+	u16 i;
+
+	ret_val = e1000e_update_nvm_checksum_generic(hw);
+	if (ret_val)
+		return ret_val;
+
+	/*
+	 * If our nvm is an EEPROM, then we're done
+	 * otherwise, commit the checksum to the flash NVM.
+	 */
+	if (hw->nvm.type != e1000_nvm_flash_hw)
+		return ret_val;
+
+	/* Check for pending operations. */
+	for (i = 0; i < E1000_FLASH_UPDATES; i++) {
+		msleep(1);
+		if ((er32(EECD) & E1000_EECD_FLUPD) == 0)
+			break;
+	}
+
+	if (i == E1000_FLASH_UPDATES)
+		return -E1000_ERR_NVM;
+
+	/* Reset the firmware if using STM opcode. */
+	if ((er32(FLOP) & 0xFF00) == E1000_STM_OPCODE) {
+		/*
+		 * The enabling of and the actual reset must be done
+		 * in two write cycles.
+		 */
+		ew32(HICR, E1000_HICR_FW_RESET_ENABLE);
+		e1e_flush();
+		ew32(HICR, E1000_HICR_FW_RESET);
+	}
+
+	/* Commit the write to flash */
+	eecd = er32(EECD) | E1000_EECD_FLUPD;
+	ew32(EECD, eecd);
+
+	for (i = 0; i < E1000_FLASH_UPDATES; i++) {
+		msleep(1);
+		if ((er32(EECD) & E1000_EECD_FLUPD) == 0)
+			break;
+	}
+
+	if (i == E1000_FLASH_UPDATES)
+		return -E1000_ERR_NVM;
+
+	return 0;
+}
+
+/**
+ *  e1000_validate_nvm_checksum_82571 - Validate EEPROM checksum
+ *  @hw: pointer to the HW structure
+ *
+ *  Calculates the EEPROM checksum by reading/adding each word of the EEPROM
+ *  and then verifies that the sum of the EEPROM is equal to 0xBABA.
+ **/
+static s32 e1000_validate_nvm_checksum_82571(struct e1000_hw *hw)
+{
+	if (hw->nvm.type == e1000_nvm_flash_hw)
+		e1000_fix_nvm_checksum_82571(hw);
+
+	return e1000e_validate_nvm_checksum_generic(hw);
+}
+
+/**
+ *  e1000_write_nvm_eewr_82571 - Write to EEPROM for 82573 silicon
+ *  @hw: pointer to the HW structure
+ *  @offset: offset within the EEPROM to be written to
+ *  @words: number of words to write
+ *  @data: 16 bit word(s) to be written to the EEPROM
+ *
+ *  After checking for invalid values, poll the EEPROM to ensure the previous
+ *  command has completed before trying to write the next word.  After write
+ *  poll for completion.
+ *
+ *  If e1000e_update_nvm_checksum is not called after this function, the
+ *  EEPROM will most likely contain an invalid checksum.
+ **/
+static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
+				      u16 words, u16 *data)
+{
+	struct e1000_nvm_info *nvm = &hw->nvm;
+	u32 i;
+	u32 eewr = 0;
+	s32 ret_val = 0;
+
+	/*
+	 * A check for invalid values:  offset too large, too many words,
+	 * and not enough words.
+	 */
+	if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
+	    (words == 0)) {
+		hw_dbg(hw, "nvm parameter(s) out of bounds\n");
+		return -E1000_ERR_NVM;
+	}
+
+	for (i = 0; i < words; i++) {
+		eewr = (data[i] << E1000_NVM_RW_REG_DATA) |
+		       ((offset+i) << E1000_NVM_RW_ADDR_SHIFT) |
+		       E1000_NVM_RW_REG_START;
+
+		ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE);
+		if (ret_val)
+			break;
+
+		ew32(EEWR, eewr);
+
+		ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE);
+		if (ret_val)
+			break;
+	}
+
+	return ret_val;
+}
+
+/**
+ *  e1000_get_cfg_done_82571 - Poll for configuration done
+ *  @hw: pointer to the HW structure
+ *
+ *  Reads the management control register for the config done bit to be set.
+ **/
+static s32 e1000_get_cfg_done_82571(struct e1000_hw *hw)
+{
+	s32 timeout = PHY_CFG_TIMEOUT;
+
+	while (timeout) {
+		if (er32(EEMNGCTL) &
+		    E1000_NVM_CFG_DONE_PORT_0)
+			break;
+		msleep(1);
+		timeout--;
+	}
+	if (!timeout) {
+		hw_dbg(hw, "MNG configuration cycle has not completed.\n");
+		return -E1000_ERR_RESET;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_set_d0_lplu_state_82571 - Set Low Power Linkup D0 state
+ *  @hw: pointer to the HW structure
+ *  @active: TRUE to enable LPLU, FALSE to disable
+ *
+ *  Sets the LPLU D0 state according to the active flag.  When activating LPLU
+ *  this function also disables smart speed and vice versa.  LPLU will not be
+ *  activated unless the device autonegotiation advertisement meets standards
+ *  of either 10 or 10/100 or 10/100/1000 at all duplexes.  This is a function
+ *  pointer entry point only called by PHY setup routines.
+ **/
+static s32 e1000_set_d0_lplu_state_82571(struct e1000_hw *hw, bool active)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 data;
+
+	ret_val = e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &data);
+	if (ret_val)
+		return ret_val;
+
+	if (active) {
+		data |= IGP02E1000_PM_D0_LPLU;
+		ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
+		if (ret_val)
+			return ret_val;
+
+		/* When LPLU is enabled, we should disable SmartSpeed */
+		ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
+		data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+		ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
+		if (ret_val)
+			return ret_val;
+	} else {
+		data &= ~IGP02E1000_PM_D0_LPLU;
+		ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
+		/*
+		 * LPLU and SmartSpeed are mutually exclusive.  LPLU is used
+		 * during Dx states where the power conservation is most
+		 * important.  During driver activity we should enable
+		 * SmartSpeed, so performance is maintained.
+		 */
+		if (phy->smart_speed == e1000_smart_speed_on) {
+			ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+					   &data);
+			if (ret_val)
+				return ret_val;
+
+			data |= IGP01E1000_PSCFR_SMART_SPEED;
+			ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+					   data);
+			if (ret_val)
+				return ret_val;
+		} else if (phy->smart_speed == e1000_smart_speed_off) {
+			ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+					   &data);
+			if (ret_val)
+				return ret_val;
+
+			data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+			ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+					   data);
+			if (ret_val)
+				return ret_val;
+		}
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_reset_hw_82571 - Reset hardware
+ *  @hw: pointer to the HW structure
+ *
+ *  This resets the hardware into a known state.  This is a
+ *  function pointer entry point called by the api module.
+ **/
+static s32 e1000_reset_hw_82571(struct e1000_hw *hw)
+{
+	u32 ctrl;
+	u32 extcnf_ctrl;
+	u32 ctrl_ext;
+	u32 icr;
+	s32 ret_val;
+	u16 i = 0;
+
+	/*
+	 * Prevent the PCI-E bus from sticking if there is no TLP connection
+	 * on the last TLP read/write transaction when MAC is reset.
+	 */
+	ret_val = e1000e_disable_pcie_master(hw);
+	if (ret_val)
+		hw_dbg(hw, "PCI-E Master disable polling has failed.\n");
+
+	hw_dbg(hw, "Masking off all interrupts\n");
+	ew32(IMC, 0xffffffff);
+
+	ew32(RCTL, 0);
+	ew32(TCTL, E1000_TCTL_PSP);
+	e1e_flush();
+
+	msleep(10);
+
+	/*
+	 * Must acquire the MDIO ownership before MAC reset.
+	 * Ownership defaults to firmware after a reset.
+	 */
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		extcnf_ctrl = er32(EXTCNF_CTRL);
+		extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+		do {
+			ew32(EXTCNF_CTRL, extcnf_ctrl);
+			extcnf_ctrl = er32(EXTCNF_CTRL);
+
+			if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
+				break;
+
+			extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+			msleep(2);
+			i++;
+		} while (i < MDIO_OWNERSHIP_TIMEOUT);
+		break;
+	default:
+		break;
+	}
+
+	ctrl = er32(CTRL);
+
+	hw_dbg(hw, "Issuing a global reset to MAC\n");
+	ew32(CTRL, ctrl | E1000_CTRL_RST);
+
+	if (hw->nvm.type == e1000_nvm_flash_hw) {
+		udelay(10);
+		ctrl_ext = er32(CTRL_EXT);
+		ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+		ew32(CTRL_EXT, ctrl_ext);
+		e1e_flush();
+	}
+
+	ret_val = e1000e_get_auto_rd_done(hw);
+	if (ret_val)
+		/* We don't want to continue accessing MAC registers. */
+		return ret_val;
+
+	/*
+	 * Phy configuration from NVM just starts after EECD_AUTO_RD is set.
+	 * Need to wait for Phy configuration completion before accessing
+	 * NVM and Phy.
+	 */
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		msleep(25);
+		break;
+	default:
+		break;
+	}
+
+	/* Clear any pending interrupt events. */
+	ew32(IMC, 0xffffffff);
+	icr = er32(ICR);
+
+	if (hw->mac.type == e1000_82571 &&
+		hw->dev_spec.e82571.alt_mac_addr_is_present)
+			e1000e_set_laa_state_82571(hw, true);
+
+	/* Reinitialize the 82571 serdes link state machine */
+	if (hw->phy.media_type == e1000_media_type_internal_serdes)
+		hw->mac.serdes_link_state = e1000_serdes_link_down;
+
+	return 0;
+}
+
+/**
+ *  e1000_init_hw_82571 - Initialize hardware
+ *  @hw: pointer to the HW structure
+ *
+ *  This inits the hardware readying it for operation.
+ **/
+static s32 e1000_init_hw_82571(struct e1000_hw *hw)
+{
+	struct e1000_mac_info *mac = &hw->mac;
+	u32 reg_data;
+	s32 ret_val;
+	u16 i;
+	u16 rar_count = mac->rar_entry_count;
+
+	e1000_initialize_hw_bits_82571(hw);
+
+	/* Initialize identification LED */
+	ret_val = e1000e_id_led_init(hw);
+	if (ret_val) {
+		hw_dbg(hw, "Error initializing identification LED\n");
+		return ret_val;
+	}
+
+	/* Disabling VLAN filtering */
+	hw_dbg(hw, "Initializing the IEEE VLAN\n");
+	e1000e_clear_vfta(hw);
+
+	/* Setup the receive address. */
+	/*
+	 * If, however, a locally administered address was assigned to the
+	 * 82571, we must reserve a RAR for it to work around an issue where
+	 * resetting one port will reload the MAC on the other port.
+	 */
+	if (e1000e_get_laa_state_82571(hw))
+		rar_count--;
+	e1000e_init_rx_addrs(hw, rar_count);
+
+	/* Zero out the Multicast HASH table */
+	hw_dbg(hw, "Zeroing the MTA\n");
+	for (i = 0; i < mac->mta_reg_count; i++)
+		E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+
+	/* Setup link and flow control */
+	ret_val = e1000_setup_link_82571(hw);
+
+	/* Set the transmit descriptor write-back policy */
+	reg_data = er32(TXDCTL(0));
+	reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+		   E1000_TXDCTL_FULL_TX_DESC_WB |
+		   E1000_TXDCTL_COUNT_DESC;
+	ew32(TXDCTL(0), reg_data);
+
+	/* ...for both queues. */
+	switch (mac->type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		e1000e_enable_tx_pkt_filtering(hw);
+		reg_data = er32(GCR);
+		reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
+		ew32(GCR, reg_data);
+		break;
+	default:
+		reg_data = er32(TXDCTL(1));
+		reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+			   E1000_TXDCTL_FULL_TX_DESC_WB |
+			   E1000_TXDCTL_COUNT_DESC;
+		ew32(TXDCTL(1), reg_data);
+		break;
+	}
+
+	/*
+	 * Clear all of the statistics registers (clear on read).  It is
+	 * important that we do this after we have tried to establish link
+	 * because the symbol error count will increment wildly if there
+	 * is no link.
+	 */
+	e1000_clear_hw_cntrs_82571(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_initialize_hw_bits_82571 - Initialize hardware-dependent bits
+ *  @hw: pointer to the HW structure
+ *
+ *  Initializes required hardware-dependent bits needed for normal operation.
+ **/
+static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw)
+{
+	u32 reg;
+
+	/* Transmit Descriptor Control 0 */
+	reg = er32(TXDCTL(0));
+	reg |= (1 << 22);
+	ew32(TXDCTL(0), reg);
+
+	/* Transmit Descriptor Control 1 */
+	reg = er32(TXDCTL(1));
+	reg |= (1 << 22);
+	ew32(TXDCTL(1), reg);
+
+	/* Transmit Arbitration Control 0 */
+	reg = er32(TARC(0));
+	reg &= ~(0xF << 27); /* 30:27 */
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		reg |= (1 << 23) | (1 << 24) | (1 << 25) | (1 << 26);
+		break;
+	default:
+		break;
+	}
+	ew32(TARC(0), reg);
+
+	/* Transmit Arbitration Control 1 */
+	reg = er32(TARC(1));
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		reg &= ~((1 << 29) | (1 << 30));
+		reg |= (1 << 22) | (1 << 24) | (1 << 25) | (1 << 26);
+		if (er32(TCTL) & E1000_TCTL_MULR)
+			reg &= ~(1 << 28);
+		else
+			reg |= (1 << 28);
+		ew32(TARC(1), reg);
+		break;
+	default:
+		break;
+	}
+
+	/* Device Control */
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		reg = er32(CTRL);
+		reg &= ~(1 << 29);
+		ew32(CTRL, reg);
+		break;
+	default:
+		break;
+	}
+
+	/* Extended Device Control */
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		reg = er32(CTRL_EXT);
+		reg &= ~(1 << 23);
+		reg |= (1 << 22);
+		ew32(CTRL_EXT, reg);
+		break;
+	default:
+		break;
+	}
+
+	if (hw->mac.type == e1000_82571) {
+		reg = er32(PBA_ECC);
+		reg |= E1000_PBA_ECC_CORR_EN;
+		ew32(PBA_ECC, reg);
+	}
+	/*
+	 * Workaround for hardware errata.
+	 * Ensure that DMA Dynamic Clock gating is disabled on 82571 and 82572
+	 */
+
+        if ((hw->mac.type == e1000_82571) ||
+           (hw->mac.type == e1000_82572)) {
+                reg = er32(CTRL_EXT);
+                reg &= ~E1000_CTRL_EXT_DMA_DYN_CLK_EN;
+                ew32(CTRL_EXT, reg);
+        }
+
+
+	/* PCI-Ex Control Registers */
+	switch (hw->mac.type) {
+	case e1000_82574:
+	case e1000_82583:
+		reg = er32(GCR);
+		reg |= (1 << 22);
+		ew32(GCR, reg);
+
+		reg = er32(GCR2);
+		reg |= 1;
+		ew32(GCR2, reg);
+		break;
+	default:
+		break;
+	}
+
+	return;
+}
+
+/**
+ *  e1000e_clear_vfta - Clear VLAN filter table
+ *  @hw: pointer to the HW structure
+ *
+ *  Clears the register array which contains the VLAN filter table by
+ *  setting all the values to 0.
+ **/
+void e1000e_clear_vfta(struct e1000_hw *hw)
+{
+	u32 offset;
+	u32 vfta_value = 0;
+	u32 vfta_offset = 0;
+	u32 vfta_bit_in_reg = 0;
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		if (hw->mng_cookie.vlan_id != 0) {
+			/*
+			 * The VFTA is a 4096b bit-field, each identifying
+			 * a single VLAN ID.  The following operations
+			 * determine which 32b entry (i.e. offset) into the
+			 * array we want to set the VLAN ID (i.e. bit) of
+			 * the manageability unit.
+			 */
+			vfta_offset = (hw->mng_cookie.vlan_id >>
+				       E1000_VFTA_ENTRY_SHIFT) &
+				      E1000_VFTA_ENTRY_MASK;
+			vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id &
+					       E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
+		}
+		break;
+	default:
+		break;
+	}
+	for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+		/*
+		 * If the offset we want to clear is the same offset of the
+		 * manageability VLAN ID, then clear all bits except that of
+		 * the manageability unit.
+		 */
+		vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
+		E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, vfta_value);
+		e1e_flush();
+	}
+}
+
+/**
+ *  e1000_check_mng_mode_82574 - Check manageability is enabled
+ *  @hw: pointer to the HW structure
+ *
+ *  Reads the NVM Initialization Control Word 2 and returns true
+ *  (>0) if any manageability is enabled, else false (0).
+ **/
+static bool e1000_check_mng_mode_82574(struct e1000_hw *hw)
+{
+	u16 data;
+
+	e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &data);
+	return (data & E1000_NVM_INIT_CTRL2_MNGM) != 0;
+}
+
+/**
+ *  e1000_led_on_82574 - Turn LED on
+ *  @hw: pointer to the HW structure
+ *
+ *  Turn LED on.
+ **/
+static s32 e1000_led_on_82574(struct e1000_hw *hw)
+{
+	u32 ctrl;
+	u32 i;
+
+	ctrl = hw->mac.ledctl_mode2;
+	if (!(E1000_STATUS_LU & er32(STATUS))) {
+		/*
+		 * If no link, then turn LED on by setting the invert bit
+		 * for each LED that's "on" (0x0E) in ledctl_mode2.
+		 */
+		for (i = 0; i < 4; i++)
+			if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
+			    E1000_LEDCTL_MODE_LED_ON)
+				ctrl |= (E1000_LEDCTL_LED0_IVRT << (i * 8));
+	}
+	ew32(LEDCTL, ctrl);
+
+	return 0;
+}
+
+/**
+ *  e1000_update_mc_addr_list_82571 - Update Multicast addresses
+ *  @hw: pointer to the HW structure
+ *  @mc_addr_list: array of multicast addresses to program
+ *  @mc_addr_count: number of multicast addresses to program
+ *  @rar_used_count: the first RAR register free to program
+ *  @rar_count: total number of supported Receive Address Registers
+ *
+ *  Updates the Receive Address Registers and Multicast Table Array.
+ *  The caller must have a packed mc_addr_list of multicast addresses.
+ *  The parameter rar_count will usually be hw->mac.rar_entry_count
+ *  unless there are workarounds that change this.
+ **/
+static void e1000_update_mc_addr_list_82571(struct e1000_hw *hw,
+					    u8 *mc_addr_list,
+					    u32 mc_addr_count,
+					    u32 rar_used_count,
+					    u32 rar_count)
+{
+	if (e1000e_get_laa_state_82571(hw))
+		rar_count--;
+
+	e1000e_update_mc_addr_list_generic(hw, mc_addr_list, mc_addr_count,
+					   rar_used_count, rar_count);
+}
+
+/**
+ *  e1000_setup_link_82571 - Setup flow control and link settings
+ *  @hw: pointer to the HW structure
+ *
+ *  Determines which flow control settings to use, then configures flow
+ *  control.  Calls the appropriate media-specific link configuration
+ *  function.  Assuming the adapter has a valid link partner, a valid link
+ *  should be established.  Assumes the hardware has previously been reset
+ *  and the transmitter and receiver are not enabled.
+ **/
+static s32 e1000_setup_link_82571(struct e1000_hw *hw)
+{
+	/*
+	 * 82573 does not have a word in the NVM to determine
+	 * the default flow control setting, so we explicitly
+	 * set it to full.
+	 */
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		if (hw->fc.requested_mode == e1000_fc_default)
+			hw->fc.requested_mode = e1000_fc_full;
+		break;
+	default:
+		break;
+	}
+
+	return e1000e_setup_link(hw);
+}
+
+/**
+ *  e1000_setup_copper_link_82571 - Configure copper link settings
+ *  @hw: pointer to the HW structure
+ *
+ *  Configures the link for auto-neg or forced speed and duplex.  Then we check
+ *  for link, once link is established calls to configure collision distance
+ *  and flow control are called.
+ **/
+static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw)
+{
+	u32 ctrl;
+	u32 led_ctrl;
+	s32 ret_val;
+
+	ctrl = er32(CTRL);
+	ctrl |= E1000_CTRL_SLU;
+	ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+	ew32(CTRL, ctrl);
+
+	switch (hw->phy.type) {
+	case e1000_phy_m88:
+	case e1000_phy_bm:
+		ret_val = e1000e_copper_link_setup_m88(hw);
+		break;
+	case e1000_phy_igp_2:
+		ret_val = e1000e_copper_link_setup_igp(hw);
+		/* Setup activity LED */
+		led_ctrl = er32(LEDCTL);
+		led_ctrl &= IGP_ACTIVITY_LED_MASK;
+		led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+		ew32(LEDCTL, led_ctrl);
+		break;
+	default:
+		return -E1000_ERR_PHY;
+		break;
+	}
+
+	if (ret_val)
+		return ret_val;
+
+	ret_val = e1000e_setup_copper_link(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_setup_fiber_serdes_link_82571 - Setup link for fiber/serdes
+ *  @hw: pointer to the HW structure
+ *
+ *  Configures collision distance and flow control for fiber and serdes links.
+ *  Upon successful setup, poll for link.
+ **/
+static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw)
+{
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		/*
+		 * If SerDes loopback mode is entered, there is no form
+		 * of reset to take the adapter out of that mode.  So we
+		 * have to explicitly take the adapter out of loopback
+		 * mode.  This prevents drivers from twiddling their thumbs
+		 * if another tool failed to take it out of loopback mode.
+		 */
+		ew32(SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
+		break;
+	default:
+		break;
+	}
+
+	return e1000e_setup_fiber_serdes_link(hw);
+}
+
+/**
+ *  e1000_check_for_serdes_link_82571 - Check for link (Serdes)
+ *  @hw: pointer to the HW structure
+ *
+ *  Checks for link up on the hardware.  If link is not up and we have
+ *  a signal, then we need to force link up.
+ **/
+static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw)
+{
+	struct e1000_mac_info *mac = &hw->mac;
+	u32 rxcw;
+	u32 ctrl;
+	u32 status;
+	s32 ret_val = 0;
+
+	ctrl = er32(CTRL);
+	status = er32(STATUS);
+	rxcw = er32(RXCW);
+
+	if ((rxcw & E1000_RXCW_SYNCH) && !(rxcw & E1000_RXCW_IV)) {
+
+		/* Receiver is synchronized with no invalid bits.  */
+		switch (mac->serdes_link_state) {
+		case e1000_serdes_link_autoneg_complete:
+			if (!(status & E1000_STATUS_LU)) {
+				/*
+				 * We have lost link, retry autoneg before
+				 * reporting link failure
+				 */
+				mac->serdes_link_state =
+				    e1000_serdes_link_autoneg_progress;
+				hw_dbg(hw, "AN_UP     -> AN_PROG\n");
+			}
+		break;
+
+		case e1000_serdes_link_forced_up:
+			/*
+			 * If we are receiving /C/ ordered sets, re-enable
+			 * auto-negotiation in the TXCW register and disable
+			 * forced link in the Device Control register in an
+			 * attempt to auto-negotiate with our link partner.
+			 */
+			if (rxcw & E1000_RXCW_C) {
+				/* Enable autoneg, and unforce link up */
+				ew32(TXCW, mac->txcw);
+				ew32(CTRL,
+				    (ctrl & ~E1000_CTRL_SLU));
+				mac->serdes_link_state =
+				    e1000_serdes_link_autoneg_progress;
+				hw_dbg(hw, "FORCED_UP -> AN_PROG\n");
+			}
+			break;
+
+		case e1000_serdes_link_autoneg_progress:
+			/*
+			 * If the LU bit is set in the STATUS register,
+			 * autoneg has completed sucessfully. If not,
+			 * try foring the link because the far end may be
+			 * available but not capable of autonegotiation.
+			 */
+			if (status & E1000_STATUS_LU)  {
+				mac->serdes_link_state =
+				    e1000_serdes_link_autoneg_complete;
+				hw_dbg(hw, "AN_PROG   -> AN_UP\n");
+			} else {
+				/*
+				 * Disable autoneg, force link up and
+				 * full duplex, and change state to forced
+				 */
+				ew32(TXCW,
+				    (mac->txcw & ~E1000_TXCW_ANE));
+				ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+				ew32(CTRL, ctrl);
+
+				/* Configure Flow Control after link up. */
+				ret_val =
+				    e1000e_config_fc_after_link_up(hw);
+				if (ret_val) {
+					hw_dbg(hw, "Error config flow control\n");
+					break;
+				}
+				mac->serdes_link_state =
+				    e1000_serdes_link_forced_up;
+				hw_dbg(hw, "AN_PROG   -> FORCED_UP\n");
+			}
+			mac->serdes_has_link = true;
+			break;
+
+		case e1000_serdes_link_down:
+		default:
+			/* The link was down but the receiver has now gained
+			 * valid sync, so lets see if we can bring the link
+			 * up. */
+			ew32(TXCW, mac->txcw);
+			ew32(CTRL,
+			    (ctrl & ~E1000_CTRL_SLU));
+			mac->serdes_link_state =
+			    e1000_serdes_link_autoneg_progress;
+			hw_dbg(hw, "DOWN      -> AN_PROG\n");
+			break;
+		}
+	} else {
+		if (!(rxcw & E1000_RXCW_SYNCH)) {
+			mac->serdes_has_link = false;
+			mac->serdes_link_state = e1000_serdes_link_down;
+			hw_dbg(hw, "ANYSTATE  -> DOWN\n");
+		} else {
+			/*
+			 * We have sync, and can tolerate one
+			 * invalid (IV) codeword before declaring
+			 * link down, so reread to look again
+			 */
+			udelay(10);
+			rxcw = er32(RXCW);
+			if (rxcw & E1000_RXCW_IV) {
+				mac->serdes_link_state = e1000_serdes_link_down;
+				mac->serdes_has_link = false;
+				hw_dbg(hw, "ANYSTATE  -> DOWN\n");
+			}
+		}
+	}
+
+	return ret_val;
+}
+
+/**
+ *  e1000_valid_led_default_82571 - Verify a valid default LED config
+ *  @hw: pointer to the HW structure
+ *  @data: pointer to the NVM (EEPROM)
+ *
+ *  Read the EEPROM for the current default LED configuration.  If the
+ *  LED configuration is not valid, set to a valid LED configuration.
+ **/
+static s32 e1000_valid_led_default_82571(struct e1000_hw *hw, u16 *data)
+{
+	s32 ret_val;
+
+	ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
+	if (ret_val) {
+		hw_dbg(hw, "NVM Read Error\n");
+		return ret_val;
+	}
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		if (*data == ID_LED_RESERVED_F746)
+			*data = ID_LED_DEFAULT_82573;
+		break;
+	default:
+		if (*data == ID_LED_RESERVED_0000 ||
+		    *data == ID_LED_RESERVED_FFFF)
+			*data = ID_LED_DEFAULT;
+		break;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000e_get_laa_state_82571 - Get locally administered address state
+ *  @hw: pointer to the HW structure
+ *
+ *  Retrieve and return the current locally administered address state.
+ **/
+bool e1000e_get_laa_state_82571(struct e1000_hw *hw)
+{
+	if (hw->mac.type != e1000_82571)
+		return 0;
+
+	return hw->dev_spec.e82571.laa_is_present;
+}
+
+/**
+ *  e1000e_set_laa_state_82571 - Set locally administered address state
+ *  @hw: pointer to the HW structure
+ *  @state: enable/disable locally administered address
+ *
+ *  Enable/Disable the current locally administers address state.
+ **/
+void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state)
+{
+	if (hw->mac.type != e1000_82571)
+		return;
+
+	hw->dev_spec.e82571.laa_is_present = state;
+
+	/* If workaround is activated... */
+	if (state)
+		/*
+		 * Hold a copy of the LAA in RAR[14] This is done so that
+		 * between the time RAR[0] gets clobbered and the time it
+		 * gets fixed, the actual LAA is in one of the RARs and no
+		 * incoming packets directed to this port are dropped.
+		 * Eventually the LAA will be in RAR[0] and RAR[14].
+		 */
+		e1000e_rar_set(hw, hw->mac.addr, hw->mac.rar_entry_count - 1);
+}
+
+/**
+ *  e1000_fix_nvm_checksum_82571 - Fix EEPROM checksum
+ *  @hw: pointer to the HW structure
+ *
+ *  Verifies that the EEPROM has completed the update.  After updating the
+ *  EEPROM, we need to check bit 15 in work 0x23 for the checksum fix.  If
+ *  the checksum fix is not implemented, we need to set the bit and update
+ *  the checksum.  Otherwise, if bit 15 is set and the checksum is incorrect,
+ *  we need to return bad checksum.
+ **/
+static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw)
+{
+	struct e1000_nvm_info *nvm = &hw->nvm;
+	s32 ret_val;
+	u16 data;
+
+	if (nvm->type != e1000_nvm_flash_hw)
+		return 0;
+
+	/*
+	 * Check bit 4 of word 10h.  If it is 0, firmware is done updating
+	 * 10h-12h.  Checksum may need to be fixed.
+	 */
+	ret_val = e1000_read_nvm(hw, 0x10, 1, &data);
+	if (ret_val)
+		return ret_val;
+
+	if (!(data & 0x10)) {
+		/*
+		 * Read 0x23 and check bit 15.  This bit is a 1
+		 * when the checksum has already been fixed.  If
+		 * the checksum is still wrong and this bit is a
+		 * 1, we need to return bad checksum.  Otherwise,
+		 * we need to set this bit to a 1 and update the
+		 * checksum.
+		 */
+		ret_val = e1000_read_nvm(hw, 0x23, 1, &data);
+		if (ret_val)
+			return ret_val;
+
+		if (!(data & 0x8000)) {
+			data |= 0x8000;
+			ret_val = e1000_write_nvm(hw, 0x23, 1, &data);
+			if (ret_val)
+				return ret_val;
+			ret_val = e1000e_update_nvm_checksum(hw);
+		}
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_clear_hw_cntrs_82571 - Clear device specific hardware counters
+ *  @hw: pointer to the HW structure
+ *
+ *  Clears the hardware counters by reading the counter registers.
+ **/
+static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw)
+{
+	u32 temp;
+
+	e1000e_clear_hw_cntrs_base(hw);
+
+	temp = er32(PRC64);
+	temp = er32(PRC127);
+	temp = er32(PRC255);
+	temp = er32(PRC511);
+	temp = er32(PRC1023);
+	temp = er32(PRC1522);
+	temp = er32(PTC64);
+	temp = er32(PTC127);
+	temp = er32(PTC255);
+	temp = er32(PTC511);
+	temp = er32(PTC1023);
+	temp = er32(PTC1522);
+
+	temp = er32(ALGNERRC);
+	temp = er32(RXERRC);
+	temp = er32(TNCRS);
+	temp = er32(CEXTERR);
+	temp = er32(TSCTC);
+	temp = er32(TSCTFC);
+
+	temp = er32(MGTPRC);
+	temp = er32(MGTPDC);
+	temp = er32(MGTPTC);
+
+	temp = er32(IAC);
+	temp = er32(ICRXOC);
+
+	temp = er32(ICRXPTC);
+	temp = er32(ICRXATC);
+	temp = er32(ICTXPTC);
+	temp = er32(ICTXATC);
+	temp = er32(ICTXQEC);
+	temp = er32(ICTXQMTC);
+	temp = er32(ICRXDMTC);
+}
+
+static struct e1000_mac_operations e82571_mac_ops = {
+	/* .check_mng_mode: mac type dependent */
+	/* .check_for_link: media type dependent */
+	.id_led_init		= e1000e_id_led_init,
+	.cleanup_led		= e1000e_cleanup_led_generic,
+	.clear_hw_cntrs		= e1000_clear_hw_cntrs_82571,
+	.get_bus_info		= e1000e_get_bus_info_pcie,
+	/* .get_link_up_info: media type dependent */
+	/* .led_on: mac type dependent */
+	.led_off		= e1000e_led_off_generic,
+	.update_mc_addr_list	= e1000_update_mc_addr_list_82571,
+	.reset_hw		= e1000_reset_hw_82571,
+	.init_hw		= e1000_init_hw_82571,
+	.setup_link		= e1000_setup_link_82571,
+	/* .setup_physical_interface: media type dependent */
+	.setup_led		= e1000e_setup_led_generic,
+};
+
+static struct e1000_phy_operations e82_phy_ops_igp = {
+	.acquire_phy		= e1000_get_hw_semaphore_82571,
+	.check_reset_block	= e1000e_check_reset_block_generic,
+	.commit_phy		= NULL,
+	.force_speed_duplex	= e1000e_phy_force_speed_duplex_igp,
+	.get_cfg_done		= e1000_get_cfg_done_82571,
+	.get_cable_length	= e1000e_get_cable_length_igp_2,
+	.get_phy_info		= e1000e_get_phy_info_igp,
+	.read_phy_reg		= e1000e_read_phy_reg_igp,
+	.release_phy		= e1000_put_hw_semaphore_82571,
+	.reset_phy		= e1000e_phy_hw_reset_generic,
+	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
+	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
+	.write_phy_reg		= e1000e_write_phy_reg_igp,
+	.cfg_on_link_up      	= NULL,
+};
+
+static struct e1000_phy_operations e82_phy_ops_m88 = {
+	.acquire_phy		= e1000_get_hw_semaphore_82571,
+	.check_reset_block	= e1000e_check_reset_block_generic,
+	.commit_phy		= e1000e_phy_sw_reset,
+	.force_speed_duplex	= e1000e_phy_force_speed_duplex_m88,
+	.get_cfg_done		= e1000e_get_cfg_done,
+	.get_cable_length	= e1000e_get_cable_length_m88,
+	.get_phy_info		= e1000e_get_phy_info_m88,
+	.read_phy_reg		= e1000e_read_phy_reg_m88,
+	.release_phy		= e1000_put_hw_semaphore_82571,
+	.reset_phy		= e1000e_phy_hw_reset_generic,
+	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
+	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
+	.write_phy_reg		= e1000e_write_phy_reg_m88,
+	.cfg_on_link_up      	= NULL,
+};
+
+static struct e1000_phy_operations e82_phy_ops_bm = {
+	.acquire_phy		= e1000_get_hw_semaphore_82571,
+	.check_reset_block	= e1000e_check_reset_block_generic,
+	.commit_phy		= e1000e_phy_sw_reset,
+	.force_speed_duplex	= e1000e_phy_force_speed_duplex_m88,
+	.get_cfg_done		= e1000e_get_cfg_done,
+	.get_cable_length	= e1000e_get_cable_length_m88,
+	.get_phy_info		= e1000e_get_phy_info_m88,
+	.read_phy_reg		= e1000e_read_phy_reg_bm2,
+	.release_phy		= e1000_put_hw_semaphore_82571,
+	.reset_phy		= e1000e_phy_hw_reset_generic,
+	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
+	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
+	.write_phy_reg		= e1000e_write_phy_reg_bm2,
+	.cfg_on_link_up      	= NULL,
+};
+
+static struct e1000_nvm_operations e82571_nvm_ops = {
+	.acquire_nvm		= e1000_acquire_nvm_82571,
+	.read_nvm		= e1000e_read_nvm_eerd,
+	.release_nvm		= e1000_release_nvm_82571,
+	.update_nvm		= e1000_update_nvm_checksum_82571,
+	.valid_led_default	= e1000_valid_led_default_82571,
+	.validate_nvm		= e1000_validate_nvm_checksum_82571,
+	.write_nvm		= e1000_write_nvm_82571,
+};
+
+struct e1000_info e1000_82571_info = {
+	.mac			= e1000_82571,
+	.flags			= FLAG_HAS_HW_VLAN_FILTER
+				  | FLAG_HAS_JUMBO_FRAMES
+				  | FLAG_HAS_WOL
+				  | FLAG_APME_IN_CTRL3
+				  | FLAG_RX_CSUM_ENABLED
+				  | FLAG_HAS_CTRLEXT_ON_LOAD
+				  | FLAG_HAS_SMART_POWER_DOWN
+				  | FLAG_RESET_OVERWRITES_LAA /* errata */
+				  | FLAG_TARC_SPEED_MODE_BIT /* errata */
+				  | FLAG_APME_CHECK_PORT_B,
+	.pba			= 38,
+	.max_hw_frame_size	= DEFAULT_JUMBO,
+	.get_variants		= e1000_get_variants_82571,
+	.mac_ops		= &e82571_mac_ops,
+	.phy_ops		= &e82_phy_ops_igp,
+	.nvm_ops		= &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82572_info = {
+	.mac			= e1000_82572,
+	.flags			= FLAG_HAS_HW_VLAN_FILTER
+				  | FLAG_HAS_JUMBO_FRAMES
+				  | FLAG_HAS_WOL
+				  | FLAG_APME_IN_CTRL3
+				  | FLAG_RX_CSUM_ENABLED
+				  | FLAG_HAS_CTRLEXT_ON_LOAD
+				  | FLAG_TARC_SPEED_MODE_BIT, /* errata */
+	.pba			= 38,
+	.max_hw_frame_size	= DEFAULT_JUMBO,
+	.get_variants		= e1000_get_variants_82571,
+	.mac_ops		= &e82571_mac_ops,
+	.phy_ops		= &e82_phy_ops_igp,
+	.nvm_ops		= &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82573_info = {
+	.mac			= e1000_82573,
+	.flags			= FLAG_HAS_HW_VLAN_FILTER
+				  | FLAG_HAS_JUMBO_FRAMES
+				  | FLAG_HAS_WOL
+				  | FLAG_APME_IN_CTRL3
+				  | FLAG_RX_CSUM_ENABLED
+				  | FLAG_HAS_SMART_POWER_DOWN
+				  | FLAG_HAS_AMT
+				  | FLAG_HAS_ERT
+				  | FLAG_HAS_SWSM_ON_LOAD,
+	.pba			= 20,
+	.max_hw_frame_size	= ETH_FRAME_LEN + ETH_FCS_LEN,
+	.get_variants		= e1000_get_variants_82571,
+	.mac_ops		= &e82571_mac_ops,
+	.phy_ops		= &e82_phy_ops_m88,
+	.nvm_ops		= &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82574_info = {
+	.mac			= e1000_82574,
+	.flags			= FLAG_HAS_HW_VLAN_FILTER
+				  | FLAG_HAS_MSIX
+				  | FLAG_HAS_JUMBO_FRAMES
+				  | FLAG_HAS_WOL
+				  | FLAG_APME_IN_CTRL3
+				  | FLAG_RX_CSUM_ENABLED
+				  | FLAG_HAS_SMART_POWER_DOWN
+				  | FLAG_HAS_AMT
+				  | FLAG_HAS_CTRLEXT_ON_LOAD,
+	.pba			= 20,
+	.max_hw_frame_size	= DEFAULT_JUMBO,
+	.get_variants		= e1000_get_variants_82571,
+	.mac_ops		= &e82571_mac_ops,
+	.phy_ops		= &e82_phy_ops_bm,
+	.nvm_ops		= &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82583_info = {
+	.mac			= e1000_82583,
+	.flags			= FLAG_HAS_HW_VLAN_FILTER
+				  | FLAG_HAS_WOL
+				  | FLAG_APME_IN_CTRL3
+				  | FLAG_RX_CSUM_ENABLED
+				  | FLAG_HAS_SMART_POWER_DOWN
+				  | FLAG_HAS_AMT
+				  | FLAG_HAS_CTRLEXT_ON_LOAD,
+	.pba			= 20,
+	.max_hw_frame_size	= ETH_FRAME_LEN + ETH_FCS_LEN,
+	.get_variants		= e1000_get_variants_82571,
+	.mac_ops		= &e82571_mac_ops,
+	.phy_ops		= &e82_phy_ops_bm,
+	.nvm_ops		= &e82571_nvm_ops,
+};
+

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000e/82571-2.6.32-orig.c	Fri Oct 28 17:09:02 2011 +0200
@@ -0,0 +1,1829 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2008 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/*
+ * 82571EB Gigabit Ethernet Controller
+ * 82571EB Gigabit Ethernet Controller (Copper)
+ * 82571EB Gigabit Ethernet Controller (Fiber)
+ * 82571EB Dual Port Gigabit Mezzanine Adapter
+ * 82571EB Quad Port Gigabit Mezzanine Adapter
+ * 82571PT Gigabit PT Quad Port Server ExpressModule
+ * 82572EI Gigabit Ethernet Controller (Copper)
+ * 82572EI Gigabit Ethernet Controller (Fiber)
+ * 82572EI Gigabit Ethernet Controller
+ * 82573V Gigabit Ethernet Controller (Copper)
+ * 82573E Gigabit Ethernet Controller (Copper)
+ * 82573L Gigabit Ethernet Controller
+ * 82574L Gigabit Network Connection
+ * 82583V Gigabit Network Connection
+ */
+
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+
+#include "e1000.h"
+
+#define ID_LED_RESERVED_F746 0xF746
+#define ID_LED_DEFAULT_82573 ((ID_LED_DEF1_DEF2 << 12) | \
+			      (ID_LED_OFF1_ON2  <<  8) | \
+			      (ID_LED_DEF1_DEF2 <<  4) | \
+			      (ID_LED_DEF1_DEF2))
+
+#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
+
+#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */
+
+static s32 e1000_get_phy_id_82571(struct e1000_hw *hw);
+static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw);
+static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw);
+static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw);
+static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
+				      u16 words, u16 *data);
+static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw);
+static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw);
+static s32 e1000_setup_link_82571(struct e1000_hw *hw);
+static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw);
+static bool e1000_check_mng_mode_82574(struct e1000_hw *hw);
+static s32 e1000_led_on_82574(struct e1000_hw *hw);
+static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw);
+
+/**
+ *  e1000_init_phy_params_82571 - Init PHY func ptrs.
+ *  @hw: pointer to the HW structure
+ *
+ *  This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_phy_params_82571(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+
+	if (hw->phy.media_type != e1000_media_type_copper) {
+		phy->type = e1000_phy_none;
+		return 0;
+	}
+
+	phy->addr			 = 1;
+	phy->autoneg_mask		 = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+	phy->reset_delay_us		 = 100;
+
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		phy->type		 = e1000_phy_igp_2;
+		break;
+	case e1000_82573:
+		phy->type		 = e1000_phy_m88;
+		break;
+	case e1000_82574:
+	case e1000_82583:
+		phy->type		 = e1000_phy_bm;
+		break;
+	default:
+		return -E1000_ERR_PHY;
+		break;
+	}
+
+	/* This can only be done after all function pointers are setup. */
+	ret_val = e1000_get_phy_id_82571(hw);
+
+	/* Verify phy id */
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		if (phy->id != IGP01E1000_I_PHY_ID)
+			return -E1000_ERR_PHY;
+		break;
+	case e1000_82573:
+		if (phy->id != M88E1111_I_PHY_ID)
+			return -E1000_ERR_PHY;
+		break;
+	case e1000_82574:
+	case e1000_82583:
+		if (phy->id != BME1000_E_PHY_ID_R2)
+			return -E1000_ERR_PHY;
+		break;
+	default:
+		return -E1000_ERR_PHY;
+		break;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_init_nvm_params_82571 - Init NVM func ptrs.
+ *  @hw: pointer to the HW structure
+ *
+ *  This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_nvm_params_82571(struct e1000_hw *hw)
+{
+	struct e1000_nvm_info *nvm = &hw->nvm;
+	u32 eecd = er32(EECD);
+	u16 size;
+
+	nvm->opcode_bits = 8;
+	nvm->delay_usec = 1;
+	switch (nvm->override) {
+	case e1000_nvm_override_spi_large:
+		nvm->page_size = 32;
+		nvm->address_bits = 16;
+		break;
+	case e1000_nvm_override_spi_small:
+		nvm->page_size = 8;
+		nvm->address_bits = 8;
+		break;
+	default:
+		nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
+		nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
+		break;
+	}
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		if (((eecd >> 15) & 0x3) == 0x3) {
+			nvm->type = e1000_nvm_flash_hw;
+			nvm->word_size = 2048;
+			/*
+			 * Autonomous Flash update bit must be cleared due
+			 * to Flash update issue.
+			 */
+			eecd &= ~E1000_EECD_AUPDEN;
+			ew32(EECD, eecd);
+			break;
+		}
+		/* Fall Through */
+	default:
+		nvm->type = e1000_nvm_eeprom_spi;
+		size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
+				  E1000_EECD_SIZE_EX_SHIFT);
+		/*
+		 * Added to a constant, "size" becomes the left-shift value
+		 * for setting word_size.
+		 */
+		size += NVM_WORD_SIZE_BASE_SHIFT;
+
+		/* EEPROM access above 16k is unsupported */
+		if (size > 14)
+			size = 14;
+		nvm->word_size	= 1 << size;
+		break;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_init_mac_params_82571 - Init MAC func ptrs.
+ *  @hw: pointer to the HW structure
+ *
+ *  This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_mac_params_82571(struct e1000_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	struct e1000_mac_info *mac = &hw->mac;
+	struct e1000_mac_operations *func = &mac->ops;
+	u32 swsm = 0;
+	u32 swsm2 = 0;
+	bool force_clear_smbi = false;
+
+	/* Set media type */
+	switch (adapter->pdev->device) {
+	case E1000_DEV_ID_82571EB_FIBER:
+	case E1000_DEV_ID_82572EI_FIBER:
+	case E1000_DEV_ID_82571EB_QUAD_FIBER:
+		hw->phy.media_type = e1000_media_type_fiber;
+		break;
+	case E1000_DEV_ID_82571EB_SERDES:
+	case E1000_DEV_ID_82572EI_SERDES:
+	case E1000_DEV_ID_82571EB_SERDES_DUAL:
+	case E1000_DEV_ID_82571EB_SERDES_QUAD:
+		hw->phy.media_type = e1000_media_type_internal_serdes;
+		break;
+	default:
+		hw->phy.media_type = e1000_media_type_copper;
+		break;
+	}
+
+	/* Set mta register count */
+	mac->mta_reg_count = 128;
+	/* Set rar entry count */
+	mac->rar_entry_count = E1000_RAR_ENTRIES;
+	/* Set if manageability features are enabled. */
+	mac->arc_subsystem_valid = (er32(FWSM) & E1000_FWSM_MODE_MASK) ? 1 : 0;
+
+	/* check for link */
+	switch (hw->phy.media_type) {
+	case e1000_media_type_copper:
+		func->setup_physical_interface = e1000_setup_copper_link_82571;
+		func->check_for_link = e1000e_check_for_copper_link;
+		func->get_link_up_info = e1000e_get_speed_and_duplex_copper;
+		break;
+	case e1000_media_type_fiber:
+		func->setup_physical_interface =
+			e1000_setup_fiber_serdes_link_82571;
+		func->check_for_link = e1000e_check_for_fiber_link;
+		func->get_link_up_info =
+			e1000e_get_speed_and_duplex_fiber_serdes;
+		break;
+	case e1000_media_type_internal_serdes:
+		func->setup_physical_interface =
+			e1000_setup_fiber_serdes_link_82571;
+		func->check_for_link = e1000_check_for_serdes_link_82571;
+		func->get_link_up_info =
+			e1000e_get_speed_and_duplex_fiber_serdes;
+		break;
+	default:
+		return -E1000_ERR_CONFIG;
+		break;
+	}
+
+	switch (hw->mac.type) {
+	case e1000_82574:
+	case e1000_82583:
+		func->check_mng_mode = e1000_check_mng_mode_82574;
+		func->led_on = e1000_led_on_82574;
+		break;
+	default:
+		func->check_mng_mode = e1000e_check_mng_mode_generic;
+		func->led_on = e1000e_led_on_generic;
+		break;
+	}
+
+	/*
+	 * Ensure that the inter-port SWSM.SMBI lock bit is clear before
+	 * first NVM or PHY acess. This should be done for single-port
+	 * devices, and for one port only on dual-port devices so that
+	 * for those devices we can still use the SMBI lock to synchronize
+	 * inter-port accesses to the PHY & NVM.
+	 */
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		swsm2 = er32(SWSM2);
+
+		if (!(swsm2 & E1000_SWSM2_LOCK)) {
+			/* Only do this for the first interface on this card */
+			ew32(SWSM2,
+			    swsm2 | E1000_SWSM2_LOCK);
+			force_clear_smbi = true;
+		} else
+			force_clear_smbi = false;
+		break;
+	default:
+		force_clear_smbi = true;
+		break;
+	}
+
+	if (force_clear_smbi) {
+		/* Make sure SWSM.SMBI is clear */
+		swsm = er32(SWSM);
+		if (swsm & E1000_SWSM_SMBI) {
+			/* This bit should not be set on a first interface, and
+			 * indicates that the bootagent or EFI code has
+			 * improperly left this bit enabled
+			 */
+			hw_dbg(hw, "Please update your 82571 Bootagent\n");
+		}
+		ew32(SWSM, swsm & ~E1000_SWSM_SMBI);
+	}
+
+	/*
+	 * Initialze device specific counter of SMBI acquisition
+	 * timeouts.
+	 */
+	 hw->dev_spec.e82571.smb_counter = 0;
+
+	return 0;
+}
+
+static s32 e1000_get_variants_82571(struct e1000_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	static int global_quad_port_a; /* global port a indication */
+	struct pci_dev *pdev = adapter->pdev;
+	u16 eeprom_data = 0;
+	int is_port_b = er32(STATUS) & E1000_STATUS_FUNC_1;
+	s32 rc;
+
+	rc = e1000_init_mac_params_82571(adapter);
+	if (rc)
+		return rc;
+
+	rc = e1000_init_nvm_params_82571(hw);
+	if (rc)
+		return rc;
+
+	rc = e1000_init_phy_params_82571(hw);
+	if (rc)
+		return rc;
+
+	/* tag quad port adapters first, it's used below */
+	switch (pdev->device) {
+	case E1000_DEV_ID_82571EB_QUAD_COPPER:
+	case E1000_DEV_ID_82571EB_QUAD_FIBER:
+	case E1000_DEV_ID_82571EB_QUAD_COPPER_LP:
+	case E1000_DEV_ID_82571PT_QUAD_COPPER:
+		adapter->flags |= FLAG_IS_QUAD_PORT;
+		/* mark the first port */
+		if (global_quad_port_a == 0)
+			adapter->flags |= FLAG_IS_QUAD_PORT_A;
+		/* Reset for multiple quad port adapters */
+		global_quad_port_a++;
+		if (global_quad_port_a == 4)
+			global_quad_port_a = 0;
+		break;
+	default:
+		break;
+	}
+
+	switch (adapter->hw.mac.type) {
+	case e1000_82571:
+		/* these dual ports don't have WoL on port B at all */
+		if (((pdev->device == E1000_DEV_ID_82571EB_FIBER) ||
+		     (pdev->device == E1000_DEV_ID_82571EB_SERDES) ||
+		     (pdev->device == E1000_DEV_ID_82571EB_COPPER)) &&
+		    (is_port_b))
+			adapter->flags &= ~FLAG_HAS_WOL;
+		/* quad ports only support WoL on port A */
+		if (adapter->flags & FLAG_IS_QUAD_PORT &&
+		    (!(adapter->flags & FLAG_IS_QUAD_PORT_A)))
+			adapter->flags &= ~FLAG_HAS_WOL;
+		/* Does not support WoL on any port */
+		if (pdev->device == E1000_DEV_ID_82571EB_SERDES_QUAD)
+			adapter->flags &= ~FLAG_HAS_WOL;
+		break;
+
+	case e1000_82573:
+		if (pdev->device == E1000_DEV_ID_82573L) {
+			if (e1000_read_nvm(&adapter->hw, NVM_INIT_3GIO_3, 1,
+				       &eeprom_data) < 0)
+				break;
+			if (!(eeprom_data & NVM_WORD1A_ASPM_MASK)) {
+				adapter->flags |= FLAG_HAS_JUMBO_FRAMES;
+				adapter->max_hw_frame_size = DEFAULT_JUMBO;
+			}
+		}
+		break;
+	default:
+		break;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_get_phy_id_82571 - Retrieve the PHY ID and revision
+ *  @hw: pointer to the HW structure
+ *
+ *  Reads the PHY registers and stores the PHY ID and possibly the PHY
+ *  revision in the hardware structure.
+ **/
+static s32 e1000_get_phy_id_82571(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 phy_id = 0;
+
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		/*
+		 * The 82571 firmware may still be configuring the PHY.
+		 * In this case, we cannot access the PHY until the
+		 * configuration is done.  So we explicitly set the
+		 * PHY ID.
+		 */
+		phy->id = IGP01E1000_I_PHY_ID;
+		break;
+	case e1000_82573:
+		return e1000e_get_phy_id(hw);
+		break;
+	case e1000_82574:
+	case e1000_82583:
+		ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+		if (ret_val)
+			return ret_val;
+
+		phy->id = (u32)(phy_id << 16);
+		udelay(20);
+		ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+		if (ret_val)
+			return ret_val;
+
+		phy->id |= (u32)(phy_id);
+		phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+		break;
+	default:
+		return -E1000_ERR_PHY;
+		break;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_get_hw_semaphore_82571 - Acquire hardware semaphore
+ *  @hw: pointer to the HW structure
+ *
+ *  Acquire the HW semaphore to access the PHY or NVM
+ **/
+static s32 e1000_get_hw_semaphore_82571(struct e1000_hw *hw)
+{
+	u32 swsm;
+	s32 sw_timeout = hw->nvm.word_size + 1;
+	s32 fw_timeout = hw->nvm.word_size + 1;
+	s32 i = 0;
+
+	/*
+	 * If we have timedout 3 times on trying to acquire
+	 * the inter-port SMBI semaphore, there is old code
+	 * operating on the other port, and it is not
+	 * releasing SMBI. Modify the number of times that
+	 * we try for the semaphore to interwork with this
+	 * older code.
+	 */
+	if (hw->dev_spec.e82571.smb_counter > 2)
+		sw_timeout = 1;
+
+	/* Get the SW semaphore */
+	while (i < sw_timeout) {
+		swsm = er32(SWSM);
+		if (!(swsm & E1000_SWSM_SMBI))
+			break;
+
+		udelay(50);
+		i++;
+	}
+
+	if (i == sw_timeout) {
+		hw_dbg(hw, "Driver can't access device - SMBI bit is set.\n");
+		hw->dev_spec.e82571.smb_counter++;
+	}
+	/* Get the FW semaphore. */
+	for (i = 0; i < fw_timeout; i++) {
+		swsm = er32(SWSM);
+		ew32(SWSM, swsm | E1000_SWSM_SWESMBI);
+
+		/* Semaphore acquired if bit latched */
+		if (er32(SWSM) & E1000_SWSM_SWESMBI)
+			break;
+
+		udelay(50);
+	}
+
+	if (i == fw_timeout) {
+		/* Release semaphores */
+		e1000_put_hw_semaphore_82571(hw);
+		hw_dbg(hw, "Driver can't access the NVM\n");
+		return -E1000_ERR_NVM;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_put_hw_semaphore_82571 - Release hardware semaphore
+ *  @hw: pointer to the HW structure
+ *
+ *  Release hardware semaphore used to access the PHY or NVM
+ **/
+static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw)
+{
+	u32 swsm;
+
+	swsm = er32(SWSM);
+	swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
+	ew32(SWSM, swsm);
+}
+
+/**
+ *  e1000_acquire_nvm_82571 - Request for access to the EEPROM
+ *  @hw: pointer to the HW structure
+ *
+ *  To gain access to the EEPROM, first we must obtain a hardware semaphore.
+ *  Then for non-82573 hardware, set the EEPROM access request bit and wait
+ *  for EEPROM access grant bit.  If the access grant bit is not set, release
+ *  hardware semaphore.
+ **/
+static s32 e1000_acquire_nvm_82571(struct e1000_hw *hw)
+{
+	s32 ret_val;
+
+	ret_val = e1000_get_hw_semaphore_82571(hw);
+	if (ret_val)
+		return ret_val;
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		break;
+	default:
+		ret_val = e1000e_acquire_nvm(hw);
+		break;
+	}
+
+	if (ret_val)
+		e1000_put_hw_semaphore_82571(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_release_nvm_82571 - Release exclusive access to EEPROM
+ *  @hw: pointer to the HW structure
+ *
+ *  Stop any current commands to the EEPROM and clear the EEPROM request bit.
+ **/
+static void e1000_release_nvm_82571(struct e1000_hw *hw)
+{
+	e1000e_release_nvm(hw);
+	e1000_put_hw_semaphore_82571(hw);
+}
+
+/**
+ *  e1000_write_nvm_82571 - Write to EEPROM using appropriate interface
+ *  @hw: pointer to the HW structure
+ *  @offset: offset within the EEPROM to be written to
+ *  @words: number of words to write
+ *  @data: 16 bit word(s) to be written to the EEPROM
+ *
+ *  For non-82573 silicon, write data to EEPROM at offset using SPI interface.
+ *
+ *  If e1000e_update_nvm_checksum is not called after this function, the
+ *  EEPROM will most likely contain an invalid checksum.
+ **/
+static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words,
+				 u16 *data)
+{
+	s32 ret_val;
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		ret_val = e1000_write_nvm_eewr_82571(hw, offset, words, data);
+		break;
+	case e1000_82571:
+	case e1000_82572:
+		ret_val = e1000e_write_nvm_spi(hw, offset, words, data);
+		break;
+	default:
+		ret_val = -E1000_ERR_NVM;
+		break;
+	}
+
+	return ret_val;
+}
+
+/**
+ *  e1000_update_nvm_checksum_82571 - Update EEPROM checksum
+ *  @hw: pointer to the HW structure
+ *
+ *  Updates the EEPROM checksum by reading/adding each word of the EEPROM
+ *  up to the checksum.  Then calculates the EEPROM checksum and writes the
+ *  value to the EEPROM.
+ **/
+static s32 e1000_update_nvm_checksum_82571(struct e1000_hw *hw)
+{
+	u32 eecd;
+	s32 ret_val;
+	u16 i;
+
+	ret_val = e1000e_update_nvm_checksum_generic(hw);
+	if (ret_val)
+		return ret_val;
+
+	/*
+	 * If our nvm is an EEPROM, then we're done
+	 * otherwise, commit the checksum to the flash NVM.
+	 */
+	if (hw->nvm.type != e1000_nvm_flash_hw)
+		return ret_val;
+
+	/* Check for pending operations. */
+	for (i = 0; i < E1000_FLASH_UPDATES; i++) {
+		msleep(1);
+		if ((er32(EECD) & E1000_EECD_FLUPD) == 0)
+			break;
+	}
+
+	if (i == E1000_FLASH_UPDATES)
+		return -E1000_ERR_NVM;
+
+	/* Reset the firmware if using STM opcode. */
+	if ((er32(FLOP) & 0xFF00) == E1000_STM_OPCODE) {
+		/*
+		 * The enabling of and the actual reset must be done
+		 * in two write cycles.
+		 */
+		ew32(HICR, E1000_HICR_FW_RESET_ENABLE);
+		e1e_flush();
+		ew32(HICR, E1000_HICR_FW_RESET);
+	}
+
+	/* Commit the write to flash */
+	eecd = er32(EECD) | E1000_EECD_FLUPD;
+	ew32(EECD, eecd);
+
+	for (i = 0; i < E1000_FLASH_UPDATES; i++) {
+		msleep(1);
+		if ((er32(EECD) & E1000_EECD_FLUPD) == 0)
+			break;
+	}
+
+	if (i == E1000_FLASH_UPDATES)
+		return -E1000_ERR_NVM;
+
+	return 0;
+}
+
+/**
+ *  e1000_validate_nvm_checksum_82571 - Validate EEPROM checksum
+ *  @hw: pointer to the HW structure
+ *
+ *  Calculates the EEPROM checksum by reading/adding each word of the EEPROM
+ *  and then verifies that the sum of the EEPROM is equal to 0xBABA.
+ **/
+static s32 e1000_validate_nvm_checksum_82571(struct e1000_hw *hw)
+{
+	if (hw->nvm.type == e1000_nvm_flash_hw)
+		e1000_fix_nvm_checksum_82571(hw);
+
+	return e1000e_validate_nvm_checksum_generic(hw);
+}
+
+/**
+ *  e1000_write_nvm_eewr_82571 - Write to EEPROM for 82573 silicon
+ *  @hw: pointer to the HW structure
+ *  @offset: offset within the EEPROM to be written to
+ *  @words: number of words to write
+ *  @data: 16 bit word(s) to be written to the EEPROM
+ *
+ *  After checking for invalid values, poll the EEPROM to ensure the previous
+ *  command has completed before trying to write the next word.  After write
+ *  poll for completion.
+ *
+ *  If e1000e_update_nvm_checksum is not called after this function, the
+ *  EEPROM will most likely contain an invalid checksum.
+ **/
+static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
+				      u16 words, u16 *data)
+{
+	struct e1000_nvm_info *nvm = &hw->nvm;
+	u32 i;
+	u32 eewr = 0;
+	s32 ret_val = 0;
+
+	/*
+	 * A check for invalid values:  offset too large, too many words,
+	 * and not enough words.
+	 */
+	if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
+	    (words == 0)) {
+		hw_dbg(hw, "nvm parameter(s) out of bounds\n");
+		return -E1000_ERR_NVM;
+	}
+
+	for (i = 0; i < words; i++) {
+		eewr = (data[i] << E1000_NVM_RW_REG_DATA) |
+		       ((offset+i) << E1000_NVM_RW_ADDR_SHIFT) |
+		       E1000_NVM_RW_REG_START;
+
+		ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE);
+		if (ret_val)
+			break;
+
+		ew32(EEWR, eewr);
+
+		ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE);
+		if (ret_val)
+			break;
+	}
+
+	return ret_val;
+}
+
+/**
+ *  e1000_get_cfg_done_82571 - Poll for configuration done
+ *  @hw: pointer to the HW structure
+ *
+ *  Reads the management control register for the config done bit to be set.
+ **/
+static s32 e1000_get_cfg_done_82571(struct e1000_hw *hw)
+{
+	s32 timeout = PHY_CFG_TIMEOUT;
+
+	while (timeout) {
+		if (er32(EEMNGCTL) &
+		    E1000_NVM_CFG_DONE_PORT_0)
+			break;
+		msleep(1);
+		timeout--;
+	}
+	if (!timeout) {
+		hw_dbg(hw, "MNG configuration cycle has not completed.\n");
+		return -E1000_ERR_RESET;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_set_d0_lplu_state_82571 - Set Low Power Linkup D0 state
+ *  @hw: pointer to the HW structure
+ *  @active: TRUE to enable LPLU, FALSE to disable
+ *
+ *  Sets the LPLU D0 state according to the active flag.  When activating LPLU
+ *  this function also disables smart speed and vice versa.  LPLU will not be
+ *  activated unless the device autonegotiation advertisement meets standards
+ *  of either 10 or 10/100 or 10/100/1000 at all duplexes.  This is a function
+ *  pointer entry point only called by PHY setup routines.
+ **/
+static s32 e1000_set_d0_lplu_state_82571(struct e1000_hw *hw, bool active)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 data;
+
+	ret_val = e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &data);
+	if (ret_val)
+		return ret_val;
+
+	if (active) {
+		data |= IGP02E1000_PM_D0_LPLU;
+		ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
+		if (ret_val)
+			return ret_val;
+
+		/* When LPLU is enabled, we should disable SmartSpeed */
+		ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
+		data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+		ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
+		if (ret_val)
+			return ret_val;
+	} else {
+		data &= ~IGP02E1000_PM_D0_LPLU;
+		ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
+		/*
+		 * LPLU and SmartSpeed are mutually exclusive.  LPLU is used
+		 * during Dx states where the power conservation is most
+		 * important.  During driver activity we should enable
+		 * SmartSpeed, so performance is maintained.
+		 */
+		if (phy->smart_speed == e1000_smart_speed_on) {
+			ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+					   &data);
+			if (ret_val)
+				return ret_val;
+
+			data |= IGP01E1000_PSCFR_SMART_SPEED;
+			ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+					   data);
+			if (ret_val)
+				return ret_val;
+		} else if (phy->smart_speed == e1000_smart_speed_off) {
+			ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+					   &data);
+			if (ret_val)
+				return ret_val;
+
+			data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+			ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+					   data);
+			if (ret_val)
+				return ret_val;
+		}
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_reset_hw_82571 - Reset hardware
+ *  @hw: pointer to the HW structure
+ *
+ *  This resets the hardware into a known state.  This is a
+ *  function pointer entry point called by the api module.
+ **/
+static s32 e1000_reset_hw_82571(struct e1000_hw *hw)
+{
+	u32 ctrl;
+	u32 extcnf_ctrl;
+	u32 ctrl_ext;
+	u32 icr;
+	s32 ret_val;
+	u16 i = 0;
+
+	/*
+	 * Prevent the PCI-E bus from sticking if there is no TLP connection
+	 * on the last TLP read/write transaction when MAC is reset.
+	 */
+	ret_val = e1000e_disable_pcie_master(hw);
+	if (ret_val)
+		hw_dbg(hw, "PCI-E Master disable polling has failed.\n");
+
+	hw_dbg(hw, "Masking off all interrupts\n");
+	ew32(IMC, 0xffffffff);
+
+	ew32(RCTL, 0);
+	ew32(TCTL, E1000_TCTL_PSP);
+	e1e_flush();
+
+	msleep(10);
+
+	/*
+	 * Must acquire the MDIO ownership before MAC reset.
+	 * Ownership defaults to firmware after a reset.
+	 */
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		extcnf_ctrl = er32(EXTCNF_CTRL);
+		extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+		do {
+			ew32(EXTCNF_CTRL, extcnf_ctrl);
+			extcnf_ctrl = er32(EXTCNF_CTRL);
+
+			if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
+				break;
+
+			extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+			msleep(2);
+			i++;
+		} while (i < MDIO_OWNERSHIP_TIMEOUT);
+		break;
+	default:
+		break;
+	}
+
+	ctrl = er32(CTRL);
+
+	hw_dbg(hw, "Issuing a global reset to MAC\n");
+	ew32(CTRL, ctrl | E1000_CTRL_RST);
+
+	if (hw->nvm.type == e1000_nvm_flash_hw) {
+		udelay(10);
+		ctrl_ext = er32(CTRL_EXT);
+		ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+		ew32(CTRL_EXT, ctrl_ext);
+		e1e_flush();
+	}
+
+	ret_val = e1000e_get_auto_rd_done(hw);
+	if (ret_val)
+		/* We don't want to continue accessing MAC registers. */
+		return ret_val;
+
+	/*
+	 * Phy configuration from NVM just starts after EECD_AUTO_RD is set.
+	 * Need to wait for Phy configuration completion before accessing
+	 * NVM and Phy.
+	 */
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		msleep(25);
+		break;
+	default:
+		break;
+	}
+
+	/* Clear any pending interrupt events. */
+	ew32(IMC, 0xffffffff);
+	icr = er32(ICR);
+
+	if (hw->mac.type == e1000_82571 &&
+		hw->dev_spec.e82571.alt_mac_addr_is_present)
+			e1000e_set_laa_state_82571(hw, true);
+
+	/* Reinitialize the 82571 serdes link state machine */
+	if (hw->phy.media_type == e1000_media_type_internal_serdes)
+		hw->mac.serdes_link_state = e1000_serdes_link_down;
+
+	return 0;
+}
+
+/**
+ *  e1000_init_hw_82571 - Initialize hardware
+ *  @hw: pointer to the HW structure
+ *
+ *  This inits the hardware readying it for operation.
+ **/
+static s32 e1000_init_hw_82571(struct e1000_hw *hw)
+{
+	struct e1000_mac_info *mac = &hw->mac;
+	u32 reg_data;
+	s32 ret_val;
+	u16 i;
+	u16 rar_count = mac->rar_entry_count;
+
+	e1000_initialize_hw_bits_82571(hw);
+
+	/* Initialize identification LED */
+	ret_val = e1000e_id_led_init(hw);
+	if (ret_val) {
+		hw_dbg(hw, "Error initializing identification LED\n");
+		return ret_val;
+	}
+
+	/* Disabling VLAN filtering */
+	hw_dbg(hw, "Initializing the IEEE VLAN\n");
+	e1000e_clear_vfta(hw);
+
+	/* Setup the receive address. */
+	/*
+	 * If, however, a locally administered address was assigned to the
+	 * 82571, we must reserve a RAR for it to work around an issue where
+	 * resetting one port will reload the MAC on the other port.
+	 */
+	if (e1000e_get_laa_state_82571(hw))
+		rar_count--;
+	e1000e_init_rx_addrs(hw, rar_count);
+
+	/* Zero out the Multicast HASH table */
+	hw_dbg(hw, "Zeroing the MTA\n");
+	for (i = 0; i < mac->mta_reg_count; i++)
+		E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+
+	/* Setup link and flow control */
+	ret_val = e1000_setup_link_82571(hw);
+
+	/* Set the transmit descriptor write-back policy */
+	reg_data = er32(TXDCTL(0));
+	reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+		   E1000_TXDCTL_FULL_TX_DESC_WB |
+		   E1000_TXDCTL_COUNT_DESC;
+	ew32(TXDCTL(0), reg_data);
+
+	/* ...for both queues. */
+	switch (mac->type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		e1000e_enable_tx_pkt_filtering(hw);
+		reg_data = er32(GCR);
+		reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
+		ew32(GCR, reg_data);
+		break;
+	default:
+		reg_data = er32(TXDCTL(1));
+		reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+			   E1000_TXDCTL_FULL_TX_DESC_WB |
+			   E1000_TXDCTL_COUNT_DESC;
+		ew32(TXDCTL(1), reg_data);
+		break;
+	}
+
+	/*
+	 * Clear all of the statistics registers (clear on read).  It is
+	 * important that we do this after we have tried to establish link
+	 * because the symbol error count will increment wildly if there
+	 * is no link.
+	 */
+	e1000_clear_hw_cntrs_82571(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_initialize_hw_bits_82571 - Initialize hardware-dependent bits
+ *  @hw: pointer to the HW structure
+ *
+ *  Initializes required hardware-dependent bits needed for normal operation.
+ **/
+static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw)
+{
+	u32 reg;
+
+	/* Transmit Descriptor Control 0 */
+	reg = er32(TXDCTL(0));
+	reg |= (1 << 22);
+	ew32(TXDCTL(0), reg);
+
+	/* Transmit Descriptor Control 1 */
+	reg = er32(TXDCTL(1));
+	reg |= (1 << 22);
+	ew32(TXDCTL(1), reg);
+
+	/* Transmit Arbitration Control 0 */
+	reg = er32(TARC(0));
+	reg &= ~(0xF << 27); /* 30:27 */
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		reg |= (1 << 23) | (1 << 24) | (1 << 25) | (1 << 26);
+		break;
+	default:
+		break;
+	}
+	ew32(TARC(0), reg);
+
+	/* Transmit Arbitration Control 1 */
+	reg = er32(TARC(1));
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		reg &= ~((1 << 29) | (1 << 30));
+		reg |= (1 << 22) | (1 << 24) | (1 << 25) | (1 << 26);
+		if (er32(TCTL) & E1000_TCTL_MULR)
+			reg &= ~(1 << 28);
+		else
+			reg |= (1 << 28);
+		ew32(TARC(1), reg);
+		break;
+	default:
+		break;
+	}
+
+	/* Device Control */
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		reg = er32(CTRL);
+		reg &= ~(1 << 29);
+		ew32(CTRL, reg);
+		break;
+	default:
+		break;
+	}
+
+	/* Extended Device Control */
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		reg = er32(CTRL_EXT);
+		reg &= ~(1 << 23);
+		reg |= (1 << 22);
+		ew32(CTRL_EXT, reg);
+		break;
+	default:
+		break;
+	}
+
+	if (hw->mac.type == e1000_82571) {
+		reg = er32(PBA_ECC);
+		reg |= E1000_PBA_ECC_CORR_EN;
+		ew32(PBA_ECC, reg);
+	}
+	/*
+	 * Workaround for hardware errata.
+	 * Ensure that DMA Dynamic Clock gating is disabled on 82571 and 82572
+	 */
+
+        if ((hw->mac.type == e1000_82571) ||
+           (hw->mac.type == e1000_82572)) {
+                reg = er32(CTRL_EXT);
+                reg &= ~E1000_CTRL_EXT_DMA_DYN_CLK_EN;
+                ew32(CTRL_EXT, reg);
+        }
+
+
+	/* PCI-Ex Control Registers */
+	switch (hw->mac.type) {
+	case e1000_82574:
+	case e1000_82583:
+		reg = er32(GCR);
+		reg |= (1 << 22);
+		ew32(GCR, reg);
+
+		reg = er32(GCR2);
+		reg |= 1;
+		ew32(GCR2, reg);
+		break;
+	default:
+		break;
+	}
+
+	return;
+}
+
+/**
+ *  e1000e_clear_vfta - Clear VLAN filter table
+ *  @hw: pointer to the HW structure
+ *
+ *  Clears the register array which contains the VLAN filter table by
+ *  setting all the values to 0.
+ **/
+void e1000e_clear_vfta(struct e1000_hw *hw)
+{
+	u32 offset;
+	u32 vfta_value = 0;
+	u32 vfta_offset = 0;
+	u32 vfta_bit_in_reg = 0;
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		if (hw->mng_cookie.vlan_id != 0) {
+			/*
+			 * The VFTA is a 4096b bit-field, each identifying
+			 * a single VLAN ID.  The following operations
+			 * determine which 32b entry (i.e. offset) into the
+			 * array we want to set the VLAN ID (i.e. bit) of
+			 * the manageability unit.
+			 */
+			vfta_offset = (hw->mng_cookie.vlan_id >>
+				       E1000_VFTA_ENTRY_SHIFT) &
+				      E1000_VFTA_ENTRY_MASK;
+			vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id &
+					       E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
+		}
+		break;
+	default:
+		break;
+	}
+	for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+		/*
+		 * If the offset we want to clear is the same offset of the
+		 * manageability VLAN ID, then clear all bits except that of
+		 * the manageability unit.
+		 */
+		vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
+		E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, vfta_value);
+		e1e_flush();
+	}
+}
+
+/**
+ *  e1000_check_mng_mode_82574 - Check manageability is enabled
+ *  @hw: pointer to the HW structure
+ *
+ *  Reads the NVM Initialization Control Word 2 and returns true
+ *  (>0) if any manageability is enabled, else false (0).
+ **/
+static bool e1000_check_mng_mode_82574(struct e1000_hw *hw)
+{
+	u16 data;
+
+	e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &data);
+	return (data & E1000_NVM_INIT_CTRL2_MNGM) != 0;
+}
+
+/**
+ *  e1000_led_on_82574 - Turn LED on
+ *  @hw: pointer to the HW structure
+ *
+ *  Turn LED on.
+ **/
+static s32 e1000_led_on_82574(struct e1000_hw *hw)
+{
+	u32 ctrl;
+	u32 i;
+
+	ctrl = hw->mac.ledctl_mode2;
+	if (!(E1000_STATUS_LU & er32(STATUS))) {
+		/*
+		 * If no link, then turn LED on by setting the invert bit
+		 * for each LED that's "on" (0x0E) in ledctl_mode2.
+		 */
+		for (i = 0; i < 4; i++)
+			if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
+			    E1000_LEDCTL_MODE_LED_ON)
+				ctrl |= (E1000_LEDCTL_LED0_IVRT << (i * 8));
+	}
+	ew32(LEDCTL, ctrl);
+
+	return 0;
+}
+
+/**
+ *  e1000_update_mc_addr_list_82571 - Update Multicast addresses
+ *  @hw: pointer to the HW structure
+ *  @mc_addr_list: array of multicast addresses to program
+ *  @mc_addr_count: number of multicast addresses to program
+ *  @rar_used_count: the first RAR register free to program
+ *  @rar_count: total number of supported Receive Address Registers
+ *
+ *  Updates the Receive Address Registers and Multicast Table Array.
+ *  The caller must have a packed mc_addr_list of multicast addresses.
+ *  The parameter rar_count will usually be hw->mac.rar_entry_count
+ *  unless there are workarounds that change this.
+ **/
+static void e1000_update_mc_addr_list_82571(struct e1000_hw *hw,
+					    u8 *mc_addr_list,
+					    u32 mc_addr_count,
+					    u32 rar_used_count,
+					    u32 rar_count)
+{
+	if (e1000e_get_laa_state_82571(hw))
+		rar_count--;
+
+	e1000e_update_mc_addr_list_generic(hw, mc_addr_list, mc_addr_count,
+					   rar_used_count, rar_count);
+}
+
+/**
+ *  e1000_setup_link_82571 - Setup flow control and link settings
+ *  @hw: pointer to the HW structure
+ *
+ *  Determines which flow control settings to use, then configures flow
+ *  control.  Calls the appropriate media-specific link configuration
+ *  function.  Assuming the adapter has a valid link partner, a valid link
+ *  should be established.  Assumes the hardware has previously been reset
+ *  and the transmitter and receiver are not enabled.
+ **/
+static s32 e1000_setup_link_82571(struct e1000_hw *hw)
+{
+	/*
+	 * 82573 does not have a word in the NVM to determine
+	 * the default flow control setting, so we explicitly
+	 * set it to full.
+	 */
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		if (hw->fc.requested_mode == e1000_fc_default)
+			hw->fc.requested_mode = e1000_fc_full;
+		break;
+	default:
+		break;
+	}
+
+	return e1000e_setup_link(hw);
+}
+
+/**
+ *  e1000_setup_copper_link_82571 - Configure copper link settings
+ *  @hw: pointer to the HW structure
+ *
+ *  Configures the link for auto-neg or forced speed and duplex.  Then we check
+ *  for link, once link is established calls to configure collision distance
+ *  and flow control are called.
+ **/
+static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw)
+{
+	u32 ctrl;
+	u32 led_ctrl;
+	s32 ret_val;
+
+	ctrl = er32(CTRL);
+	ctrl |= E1000_CTRL_SLU;
+	ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+	ew32(CTRL, ctrl);
+
+	switch (hw->phy.type) {
+	case e1000_phy_m88:
+	case e1000_phy_bm:
+		ret_val = e1000e_copper_link_setup_m88(hw);
+		break;
+	case e1000_phy_igp_2:
+		ret_val = e1000e_copper_link_setup_igp(hw);
+		/* Setup activity LED */
+		led_ctrl = er32(LEDCTL);
+		led_ctrl &= IGP_ACTIVITY_LED_MASK;
+		led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+		ew32(LEDCTL, led_ctrl);
+		break;
+	default:
+		return -E1000_ERR_PHY;
+		break;
+	}
+
+	if (ret_val)
+		return ret_val;
+
+	ret_val = e1000e_setup_copper_link(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_setup_fiber_serdes_link_82571 - Setup link for fiber/serdes
+ *  @hw: pointer to the HW structure
+ *
+ *  Configures collision distance and flow control for fiber and serdes links.
+ *  Upon successful setup, poll for link.
+ **/
+static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw)
+{
+	switch (hw->mac.type) {
+	case e1000_82571:
+	case e1000_82572:
+		/*
+		 * If SerDes loopback mode is entered, there is no form
+		 * of reset to take the adapter out of that mode.  So we
+		 * have to explicitly take the adapter out of loopback
+		 * mode.  This prevents drivers from twiddling their thumbs
+		 * if another tool failed to take it out of loopback mode.
+		 */
+		ew32(SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
+		break;
+	default:
+		break;
+	}
+
+	return e1000e_setup_fiber_serdes_link(hw);
+}
+
+/**
+ *  e1000_check_for_serdes_link_82571 - Check for link (Serdes)
+ *  @hw: pointer to the HW structure
+ *
+ *  Checks for link up on the hardware.  If link is not up and we have
+ *  a signal, then we need to force link up.
+ **/
+static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw)
+{
+	struct e1000_mac_info *mac = &hw->mac;
+	u32 rxcw;
+	u32 ctrl;
+	u32 status;
+	s32 ret_val = 0;
+
+	ctrl = er32(CTRL);
+	status = er32(STATUS);
+	rxcw = er32(RXCW);
+
+	if ((rxcw & E1000_RXCW_SYNCH) && !(rxcw & E1000_RXCW_IV)) {
+
+		/* Receiver is synchronized with no invalid bits.  */
+		switch (mac->serdes_link_state) {
+		case e1000_serdes_link_autoneg_complete:
+			if (!(status & E1000_STATUS_LU)) {
+				/*
+				 * We have lost link, retry autoneg before
+				 * reporting link failure
+				 */
+				mac->serdes_link_state =
+				    e1000_serdes_link_autoneg_progress;
+				hw_dbg(hw, "AN_UP     -> AN_PROG\n");
+			}
+		break;
+
+		case e1000_serdes_link_forced_up:
+			/*
+			 * If we are receiving /C/ ordered sets, re-enable
+			 * auto-negotiation in the TXCW register and disable
+			 * forced link in the Device Control register in an
+			 * attempt to auto-negotiate with our link partner.
+			 */
+			if (rxcw & E1000_RXCW_C) {
+				/* Enable autoneg, and unforce link up */
+				ew32(TXCW, mac->txcw);
+				ew32(CTRL,
+				    (ctrl & ~E1000_CTRL_SLU));
+				mac->serdes_link_state =
+				    e1000_serdes_link_autoneg_progress;
+				hw_dbg(hw, "FORCED_UP -> AN_PROG\n");
+			}
+			break;
+
+		case e1000_serdes_link_autoneg_progress:
+			/*
+			 * If the LU bit is set in the STATUS register,
+			 * autoneg has completed sucessfully. If not,
+			 * try foring the link because the far end may be
+			 * available but not capable of autonegotiation.
+			 */
+			if (status & E1000_STATUS_LU)  {
+				mac->serdes_link_state =
+				    e1000_serdes_link_autoneg_complete;
+				hw_dbg(hw, "AN_PROG   -> AN_UP\n");
+			} else {
+				/*
+				 * Disable autoneg, force link up and
+				 * full duplex, and change state to forced
+				 */
+				ew32(TXCW,
+				    (mac->txcw & ~E1000_TXCW_ANE));
+				ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+				ew32(CTRL, ctrl);
+
+				/* Configure Flow Control after link up. */
+				ret_val =
+				    e1000e_config_fc_after_link_up(hw);
+				if (ret_val) {
+					hw_dbg(hw, "Error config flow control\n");
+					break;
+				}
+				mac->serdes_link_state =
+				    e1000_serdes_link_forced_up;
+				hw_dbg(hw, "AN_PROG   -> FORCED_UP\n");
+			}
+			mac->serdes_has_link = true;
+			break;
+
+		case e1000_serdes_link_down:
+		default:
+			/* The link was down but the receiver has now gained
+			 * valid sync, so lets see if we can bring the link
+			 * up. */
+			ew32(TXCW, mac->txcw);
+			ew32(CTRL,
+			    (ctrl & ~E1000_CTRL_SLU));
+			mac->serdes_link_state =
+			    e1000_serdes_link_autoneg_progress;
+			hw_dbg(hw, "DOWN      -> AN_PROG\n");
+			break;
+		}
+	} else {
+		if (!(rxcw & E1000_RXCW_SYNCH)) {
+			mac->serdes_has_link = false;
+			mac->serdes_link_state = e1000_serdes_link_down;
+			hw_dbg(hw, "ANYSTATE  -> DOWN\n");
+		} else {
+			/*
+			 * We have sync, and can tolerate one
+			 * invalid (IV) codeword before declaring
+			 * link down, so reread to look again
+			 */
+			udelay(10);
+			rxcw = er32(RXCW);
+			if (rxcw & E1000_RXCW_IV) {
+				mac->serdes_link_state = e1000_serdes_link_down;
+				mac->serdes_has_link = false;
+				hw_dbg(hw, "ANYSTATE  -> DOWN\n");
+			}
+		}
+	}
+
+	return ret_val;
+}
+
+/**
+ *  e1000_valid_led_default_82571 - Verify a valid default LED config
+ *  @hw: pointer to the HW structure
+ *  @data: pointer to the NVM (EEPROM)
+ *
+ *  Read the EEPROM for the current default LED configuration.  If the
+ *  LED configuration is not valid, set to a valid LED configuration.
+ **/
+static s32 e1000_valid_led_default_82571(struct e1000_hw *hw, u16 *data)
+{
+	s32 ret_val;
+
+	ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
+	if (ret_val) {
+		hw_dbg(hw, "NVM Read Error\n");
+		return ret_val;
+	}
+
+	switch (hw->mac.type) {
+	case e1000_82573:
+	case e1000_82574:
+	case e1000_82583:
+		if (*data == ID_LED_RESERVED_F746)
+			*data = ID_LED_DEFAULT_82573;
+		break;
+	default:
+		if (*data == ID_LED_RESERVED_0000 ||
+		    *data == ID_LED_RESERVED_FFFF)
+			*data = ID_LED_DEFAULT;
+		break;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000e_get_laa_state_82571 - Get locally administered address state
+ *  @hw: pointer to the HW structure
+ *
+ *  Retrieve and return the current locally administered address state.
+ **/
+bool e1000e_get_laa_state_82571(struct e1000_hw *hw)
+{
+	if (hw->mac.type != e1000_82571)
+		return 0;
+
+	return hw->dev_spec.e82571.laa_is_present;
+}
+
+/**
+ *  e1000e_set_laa_state_82571 - Set locally administered address state
+ *  @hw: pointer to the HW structure
+ *  @state: enable/disable locally administered address
+ *
+ *  Enable/Disable the current locally administers address state.
+ **/
+void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state)
+{
+	if (hw->mac.type != e1000_82571)
+		return;
+
+	hw->dev_spec.e82571.laa_is_present = state;
+
+	/* If workaround is activated... */
+	if (state)
+		/*
+		 * Hold a copy of the LAA in RAR[14] This is done so that
+		 * between the time RAR[0] gets clobbered and the time it
+		 * gets fixed, the actual LAA is in one of the RARs and no
+		 * incoming packets directed to this port are dropped.
+		 * Eventually the LAA will be in RAR[0] and RAR[14].
+		 */
+		e1000e_rar_set(hw, hw->mac.addr, hw->mac.rar_entry_count - 1);
+}
+
+/**
+ *  e1000_fix_nvm_checksum_82571 - Fix EEPROM checksum
+ *  @hw: pointer to the HW structure
+ *
+ *  Verifies that the EEPROM has completed the update.  After updating the
+ *  EEPROM, we need to check bit 15 in work 0x23 for the checksum fix.  If
+ *  the checksum fix is not implemented, we need to set the bit and update
+ *  the checksum.  Otherwise, if bit 15 is set and the checksum is incorrect,
+ *  we need to return bad checksum.
+ **/
+static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw)
+{
+	struct e1000_nvm_info *nvm = &hw->nvm;
+	s32 ret_val;
+	u16 data;
+
+	if (nvm->type != e1000_nvm_flash_hw)
+		return 0;
+
+	/*
+	 * Check bit 4 of word 10h.  If it is 0, firmware is done updating
+	 * 10h-12h.  Checksum may need to be fixed.
+	 */
+	ret_val = e1000_read_nvm(hw, 0x10, 1, &data);
+	if (ret_val)
+		return ret_val;
+
+	if (!(data & 0x10)) {
+		/*
+		 * Read 0x23 and check bit 15.  This bit is a 1
+		 * when the checksum has already been fixed.  If
+		 * the checksum is still wrong and this bit is a
+		 * 1, we need to return bad checksum.  Otherwise,
+		 * we need to set this bit to a 1 and update the
+		 * checksum.
+		 */
+		ret_val = e1000_read_nvm(hw, 0x23, 1, &data);
+		if (ret_val)
+			return ret_val;
+
+		if (!(data & 0x8000)) {
+			data |= 0x8000;
+			ret_val = e1000_write_nvm(hw, 0x23, 1, &data);
+			if (ret_val)
+				return ret_val;
+			ret_val = e1000e_update_nvm_checksum(hw);
+		}
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_clear_hw_cntrs_82571 - Clear device specific hardware counters
+ *  @hw: pointer to the HW structure
+ *
+ *  Clears the hardware counters by reading the counter registers.
+ **/
+static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw)
+{
+	u32 temp;
+
+	e1000e_clear_hw_cntrs_base(hw);
+
+	temp = er32(PRC64);
+	temp = er32(PRC127);
+	temp = er32(PRC255);
+	temp = er32(PRC511);
+	temp = er32(PRC1023);
+	temp = er32(PRC1522);
+	temp = er32(PTC64);
+	temp = er32(PTC127);
+	temp = er32(PTC255);
+	temp = er32(PTC511);
+	temp = er32(PTC1023);
+	temp = er32(PTC1522);
+
+	temp = er32(ALGNERRC);
+	temp = er32(RXERRC);
+	temp = er32(TNCRS);
+	temp = er32(CEXTERR);
+	temp = er32(TSCTC);
+	temp = er32(TSCTFC);
+
+	temp = er32(MGTPRC);
+	temp = er32(MGTPDC);
+	temp = er32(MGTPTC);
+
+	temp = er32(IAC);
+	temp = er32(ICRXOC);
+
+	temp = er32(ICRXPTC);
+	temp = er32(ICRXATC);
+	temp = er32(ICTXPTC);
+	temp = er32(ICTXATC);
+	temp = er32(ICTXQEC);
+	temp = er32(ICTXQMTC);
+	temp = er32(ICRXDMTC);
+}
+
+static struct e1000_mac_operations e82571_mac_ops = {
+	/* .check_mng_mode: mac type dependent */
+	/* .check_for_link: media type dependent */
+	.id_led_init		= e1000e_id_led_init,
+	.cleanup_led		= e1000e_cleanup_led_generic,
+	.clear_hw_cntrs		= e1000_clear_hw_cntrs_82571,
+	.get_bus_info		= e1000e_get_bus_info_pcie,
+	/* .get_link_up_info: media type dependent */
+	/* .led_on: mac type dependent */
+	.led_off		= e1000e_led_off_generic,
+	.update_mc_addr_list	= e1000_update_mc_addr_list_82571,
+	.reset_hw		= e1000_reset_hw_82571,
+	.init_hw		= e1000_init_hw_82571,
+	.setup_link		= e1000_setup_link_82571,
+	/* .setup_physical_interface: media type dependent */
+	.setup_led		= e1000e_setup_led_generic,
+};
+
+static struct e1000_phy_operations e82_phy_ops_igp = {
+	.acquire_phy		= e1000_get_hw_semaphore_82571,
+	.check_reset_block	= e1000e_check_reset_block_generic,
+	.commit_phy		= NULL,
+	.force_speed_duplex	= e1000e_phy_force_speed_duplex_igp,
+	.get_cfg_done		= e1000_get_cfg_done_82571,
+	.get_cable_length	= e1000e_get_cable_length_igp_2,
+	.get_phy_info		= e1000e_get_phy_info_igp,
+	.read_phy_reg		= e1000e_read_phy_reg_igp,
+	.release_phy		= e1000_put_hw_semaphore_82571,
+	.reset_phy		= e1000e_phy_hw_reset_generic,
+	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
+	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
+	.write_phy_reg		= e1000e_write_phy_reg_igp,
+	.cfg_on_link_up      	= NULL,
+};
+
+static struct e1000_phy_operations e82_phy_ops_m88 = {
+	.acquire_phy		= e1000_get_hw_semaphore_82571,
+	.check_reset_block	= e1000e_check_reset_block_generic,
+	.commit_phy		= e1000e_phy_sw_reset,
+	.force_speed_duplex	= e1000e_phy_force_speed_duplex_m88,
+	.get_cfg_done		= e1000e_get_cfg_done,
+	.get_cable_length	= e1000e_get_cable_length_m88,
+	.get_phy_info		= e1000e_get_phy_info_m88,
+	.read_phy_reg		= e1000e_read_phy_reg_m88,
+	.release_phy		= e1000_put_hw_semaphore_82571,
+	.reset_phy		= e1000e_phy_hw_reset_generic,
+	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
+	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
+	.write_phy_reg		= e1000e_write_phy_reg_m88,
+	.cfg_on_link_up      	= NULL,
+};
+
+static struct e1000_phy_operations e82_phy_ops_bm = {
+	.acquire_phy		= e1000_get_hw_semaphore_82571,
+	.check_reset_block	= e1000e_check_reset_block_generic,
+	.commit_phy		= e1000e_phy_sw_reset,
+	.force_speed_duplex	= e1000e_phy_force_speed_duplex_m88,
+	.get_cfg_done		= e1000e_get_cfg_done,
+	.get_cable_length	= e1000e_get_cable_length_m88,
+	.get_phy_info		= e1000e_get_phy_info_m88,
+	.read_phy_reg		= e1000e_read_phy_reg_bm2,
+	.release_phy		= e1000_put_hw_semaphore_82571,
+	.reset_phy		= e1000e_phy_hw_reset_generic,
+	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
+	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
+	.write_phy_reg		= e1000e_write_phy_reg_bm2,
+	.cfg_on_link_up      	= NULL,
+};
+
+static struct e1000_nvm_operations e82571_nvm_ops = {
+	.acquire_nvm		= e1000_acquire_nvm_82571,
+	.read_nvm		= e1000e_read_nvm_eerd,
+	.release_nvm		= e1000_release_nvm_82571,
+	.update_nvm		= e1000_update_nvm_checksum_82571,
+	.valid_led_default	= e1000_valid_led_default_82571,
+	.validate_nvm		= e1000_validate_nvm_checksum_82571,
+	.write_nvm		= e1000_write_nvm_82571,
+};
+
+struct e1000_info e1000_82571_info = {
+	.mac			= e1000_82571,
+	.flags			= FLAG_HAS_HW_VLAN_FILTER
+				  | FLAG_HAS_JUMBO_FRAMES
+				  | FLAG_HAS_WOL
+				  | FLAG_APME_IN_CTRL3
+				  | FLAG_RX_CSUM_ENABLED
+				  | FLAG_HAS_CTRLEXT_ON_LOAD
+				  | FLAG_HAS_SMART_POWER_DOWN
+				  | FLAG_RESET_OVERWRITES_LAA /* errata */
+				  | FLAG_TARC_SPEED_MODE_BIT /* errata */
+				  | FLAG_APME_CHECK_PORT_B,
+	.pba			= 38,
+	.max_hw_frame_size	= DEFAULT_JUMBO,
+	.get_variants		= e1000_get_variants_82571,
+	.mac_ops		= &e82571_mac_ops,
+	.phy_ops		= &e82_phy_ops_igp,
+	.nvm_ops		= &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82572_info = {
+	.mac			= e1000_82572,
+	.flags			= FLAG_HAS_HW_VLAN_FILTER
+				  | FLAG_HAS_JUMBO_FRAMES
+				  | FLAG_HAS_WOL
+				  | FLAG_APME_IN_CTRL3
+				  | FLAG_RX_CSUM_ENABLED
+				  | FLAG_HAS_CTRLEXT_ON_LOAD
+				  | FLAG_TARC_SPEED_MODE_BIT, /* errata */
+	.pba			= 38,
+	.max_hw_frame_size	= DEFAULT_JUMBO,
+	.get_variants		= e1000_get_variants_82571,
+	.mac_ops		= &e82571_mac_ops,
+	.phy_ops		= &e82_phy_ops_igp,
+	.nvm_ops		= &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82573_info = {
+	.mac			= e1000_82573,
+	.flags			= FLAG_HAS_HW_VLAN_FILTER
+				  | FLAG_HAS_JUMBO_FRAMES
+				  | FLAG_HAS_WOL
+				  | FLAG_APME_IN_CTRL3
+				  | FLAG_RX_CSUM_ENABLED
+				  | FLAG_HAS_SMART_POWER_DOWN
+				  | FLAG_HAS_AMT
+				  | FLAG_HAS_ERT
+				  | FLAG_HAS_SWSM_ON_LOAD,
+	.pba			= 20,
+	.max_hw_frame_size	= ETH_FRAME_LEN + ETH_FCS_LEN,
+	.get_variants		= e1000_get_variants_82571,
+	.mac_ops		= &e82571_mac_ops,
+	.phy_ops		= &e82_phy_ops_m88,
+	.nvm_ops		= &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82574_info = {
+	.mac			= e1000_82574,
+	.flags			= FLAG_HAS_HW_VLAN_FILTER
+				  | FLAG_HAS_MSIX
+				  | FLAG_HAS_JUMBO_FRAMES
+				  | FLAG_HAS_WOL
+				  | FLAG_APME_IN_CTRL3
+				  | FLAG_RX_CSUM_ENABLED
+				  | FLAG_HAS_SMART_POWER_DOWN
+				  | FLAG_HAS_AMT
+				  | FLAG_HAS_CTRLEXT_ON_LOAD,
+	.pba			= 20,
+	.max_hw_frame_size	= DEFAULT_JUMBO,
+	.get_variants		= e1000_get_variants_82571,
+	.mac_ops		= &e82571_mac_ops,
+	.phy_ops		= &e82_phy_ops_bm,
+	.nvm_ops		= &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82583_info = {
+	.mac			= e1000_82583,
+	.flags			= FLAG_HAS_HW_VLAN_FILTER
+				  | FLAG_HAS_WOL
+				  | FLAG_APME_IN_CTRL3
+				  | FLAG_RX_CSUM_ENABLED
+				  | FLAG_HAS_SMART_POWER_DOWN
+				  | FLAG_HAS_AMT
+				  | FLAG_HAS_CTRLEXT_ON_LOAD,
+	.pba			= 20,
+	.max_hw_frame_size	= ETH_FRAME_LEN + ETH_FCS_LEN,
+	.get_variants		= e1000_get_variants_82571,
+	.mac_ops		= &e82571_mac_ops,
+	.phy_ops		= &e82_phy_ops_bm,
+	.nvm_ops		= &e82571_nvm_ops,
+};
+

--- a/devices/e1000e/Makefile.am	Fri Oct 28 13:07:54 2011 +0200
+++ b/devices/e1000e/Makefile.am	Fri Oct 28 17:09:02 2011 +0200
@@ -28,47 +28,69 @@
 #------------------------------------------------------------------------------
 
 EXTRA_DIST = \
+	82571-2.6.32-ethercat.c \
+	82571-2.6.32-orig.c \
 	82571-2.6.34-ethercat.c \
 	82571-2.6.34-orig.c \
 	82571-2.6.37-ethercat.c \
 	82571-2.6.37-orig.c \
 	Kbuild.in \
+	defines-2.6.32-ethercat.h \
+	defines-2.6.32-orig.h \
 	defines-2.6.34-ethercat.h \
 	defines-2.6.34-orig.h \
 	defines-2.6.37-ethercat.h \
 	defines-2.6.37-orig.h \
+	e1000-2.6.32-ethercat.h \
+	e1000-2.6.32-orig.h \
 	e1000-2.6.34-ethercat.h \
 	e1000-2.6.34-orig.h \
 	e1000-2.6.37-ethercat.h \
 	e1000-2.6.37-orig.h \
+	es2lan-2.6.32-ethercat.c \
+	es2lan-2.6.32-orig.c \
 	es2lan-2.6.34-ethercat.c \
 	es2lan-2.6.34-orig.c \
 	es2lan-2.6.37-ethercat.c \
 	es2lan-2.6.37-orig.c \
+	ethtool-2.6.32-ethercat.c \
+	ethtool-2.6.32-orig.c \
 	ethtool-2.6.34-ethercat.c \
 	ethtool-2.6.34-orig.c \
 	ethtool-2.6.37-ethercat.c \
 	ethtool-2.6.37-orig.c \
+	hw-2.6.32-ethercat.h \
+	hw-2.6.32-orig.h \
 	hw-2.6.34-ethercat.h \
 	hw-2.6.34-orig.h \
 	hw-2.6.37-ethercat.h \
 	hw-2.6.37-orig.h \
+	ich8lan-2.6.32-ethercat.c \
+	ich8lan-2.6.32-orig.c \
 	ich8lan-2.6.34-ethercat.c \
 	ich8lan-2.6.34-orig.c \
 	ich8lan-2.6.37-ethercat.c \
 	ich8lan-2.6.37-orig.c \
+	lib-2.6.32-ethercat.c \
+	lib-2.6.32-orig.c \
 	lib-2.6.34-ethercat.c \
 	lib-2.6.34-orig.c \
 	lib-2.6.37-ethercat.c \
 	lib-2.6.37-orig.c \
+	netdev-2.6.32-ethercat.c \
+	netdev-2.6.32-orig.c \
 	netdev-2.6.34-ethercat.c \
 	netdev-2.6.34-orig.c \
 	netdev-2.6.37-ethercat.c \
 	netdev-2.6.37-orig.c \
+	param-2.6.32-ethercat.c \
+	param-2.6.32-orig.c \
 	param-2.6.34-ethercat.c \
 	param-2.6.34-orig.c \
 	param-2.6.37-ethercat.c \
 	param-2.6.37-orig.c \
+	phy-2.6.32-ethercat.c \
+	phy-2.6.32-orig.c \
 	phy-2.6.34-ethercat.c \
 	phy-2.6.34-orig.c \
 	phy-2.6.37-ethercat.c \

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/devices/e1000e/defines-2.6.32-ethercat.h	Fri Oct 28 17:09:02 2011 +0200
@@ -0,0 +1,815 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2008 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000_DEFINES_H_
+#define _E1000_DEFINES_H_
+
+#define E1000_TXD_POPTS_IXSM 0x01       /* Insert IP checksum */
+#define E1000_TXD_POPTS_TXSM 0x02       /* Insert TCP/UDP checksum */
+#define E1000_TXD_CMD_EOP    0x01000000 /* End of Packet */
+#define E1000_TXD_CMD_IFCS   0x02000000 /* Insert FCS (Ethernet CRC) */
+#define E1000_TXD_CMD_IC     0x04000000 /* Insert Checksum */
+#define E1000_TXD_CMD_RS     0x08000000 /* Report Status */
+#define E1000_TXD_CMD_RPS    0x10000000 /* Report Packet Sent */
+#define E1000_TXD_CMD_DEXT   0x20000000 /* Descriptor extension (0 = legacy) */
+#define E1000_TXD_CMD_VLE    0x40000000 /* Add VLAN tag */
+#define E1000_TXD_CMD_IDE    0x80000000 /* Enable Tidv register */
+#define E1000_TXD_STAT_DD    0x00000001 /* Descriptor Done */
+#define E1000_TXD_STAT_EC    0x00000002 /* Excess Collisions */
+#define E1000_TXD_STAT_LC    0x00000004 /* Late Collisions */
+#define E1000_TXD_STAT_TU    0x00000008 /* Transmit underrun */
+#define E1000_TXD_CMD_TCP    0x01000000 /* TCP packet */
+#define E1000_TXD_CMD_IP     0x02000000 /* IP packet */
+#define E1000_TXD_CMD_TSE    0x04000000 /* TCP Seg enable */
+#define E1000_TXD_STAT_TC    0x00000004 /* Tx Underrun */
+
+/* Number of Transmit and Receive Descriptors must be a multiple of 8 */
+#define REQ_TX_DESCRIPTOR_MULTIPLE  8
+#define REQ_RX_DESCRIPTOR_MULTIPLE  8
+
+/* Definitions for power management and wakeup registers */
+/* Wake Up Control */
+#define E1000_WUC_APME       0x00000001 /* APM Enable */
+#define E1000_WUC_PME_EN     0x00000002 /* PME Enable */
+#define E1000_WUC_PHY_WAKE   0x00000100 /* if PHY supports wakeup */
+
+/* Wake Up Filter Control */
+#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
+#define E1000_WUFC_MAG  0x00000002 /* Magic Packet Wakeup Enable */
+#define E1000_WUFC_EX   0x00000004 /* Directed Exact Wakeup Enable */
+#define E1000_WUFC_MC   0x00000008 /* Directed Multicast Wakeup Enable */
+#define E1000_WUFC_BC   0x00000010 /* Broadcast Wakeup Enable */
+#define E1000_WUFC_ARP  0x00000020 /* ARP Request Packet Wakeup Enable */
+
+/* Wake Up Status */
+#define E1000_WUS_LNKC         E1000_WUFC_LNKC
+#define E1000_WUS_MAG          E1000_WUFC_MAG
+#define E1000_WUS_EX           E1000_WUFC_EX
+#define E1000_WUS_MC           E1000_WUFC_MC
+#define E1000_WUS_BC           E1000_WUFC_BC
+
+/* Extended Device Control */
+#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
+#define E1000_CTRL_EXT_EE_RST    0x00002000 /* Reinitialize from EEPROM */
+#define E1000_CTRL_EXT_SPD_BYPS  0x00008000 /* Speed Select Bypass */
+#define E1000_CTRL_EXT_RO_DIS    0x00020000 /* Relaxed Ordering disable */
+#define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */
+#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES  0x00C00000
+#define E1000_CTRL_EXT_EIAME          0x01000000
+#define E1000_CTRL_EXT_DRV_LOAD       0x10000000 /* Driver loaded bit for FW */
+#define E1000_CTRL_EXT_IAME           0x08000000 /* Interrupt acknowledge Auto-mask */
+#define E1000_CTRL_EXT_INT_TIMER_CLR  0x20000000 /* Clear Interrupt timers after IMS clear */
+#define E1000_CTRL_EXT_PBA_CLR        0x80000000 /* PBA Clear */
+#define E1000_CTRL_EXT_PHYPDEN        0x00100000
+
+/* Receive Descriptor bit definitions */
+#define E1000_RXD_STAT_DD       0x01    /* Descriptor Done */
+#define E1000_RXD_STAT_EOP      0x02    /* End of Packet */
+#define E1000_RXD_STAT_IXSM     0x04    /* Ignore checksum */
+#define E1000_RXD_STAT_VP       0x08    /* IEEE VLAN Packet */
+#define E1000_RXD_STAT_UDPCS    0x10    /* UDP xsum calculated */
+#define E1000_RXD_STAT_TCPCS    0x20    /* TCP xsum calculated */
+#define E1000_RXD_ERR_CE        0x01    /* CRC Error */
+#define E1000_RXD_ERR_SE        0x02    /* Symbol Error */
+#define E1000_RXD_ERR_SEQ       0x04    /* Sequence Error */
+#define E1000_RXD_ERR_CXE       0x10    /* Carrier Extension Error */
+#define E1000_RXD_ERR_TCPE      0x20    /* TCP/UDP Checksum Error */
+#define E1000_RXD_ERR_RXE       0x80    /* Rx Data Error */
+#define E1000_RXD_SPC_VLAN_MASK 0x0FFF  /* VLAN ID is in lower 12 bits */
+
+#define E1000_RXDEXT_STATERR_CE    0x01000000
+#define E1000_RXDEXT_STATERR_SE    0x02000000
+#define E1000_RXDEXT_STATERR_SEQ   0x04000000
+#define E1000_RXDEXT_STATERR_CXE   0x10000000
+#define E1000_RXDEXT_STATERR_RXE   0x80000000
+
+/* mask to determine if packets should be dropped due to frame errors */
+#define E1000_RXD_ERR_FRAME_ERR_MASK ( \
+    E1000_RXD_ERR_CE  |                \
+    E1000_RXD_ERR_SE  |                \
+    E1000_RXD_ERR_SEQ |                \
+    E1000_RXD_ERR_CXE |                \
+    E1000_RXD_ERR_RXE)
+
+/* Same mask, but for extended and packet split descriptors */
+#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
+    E1000_RXDEXT_STATERR_CE  |            \
+    E1000_RXDEXT_STATERR_SE  |            \
+    E1000_RXDEXT_STATERR_SEQ |            \
+    E1000_RXDEXT_STATERR_CXE |            \
+    E1000_RXDEXT_STATERR_RXE)
+
+#define E1000_RXDPS_HDRSTAT_HDRSP              0x00008000
+
+/* Management Control */
+#define E1000_MANC_SMBUS_EN      0x00000001 /* SMBus Enabled - RO */
+#define E1000_MANC_ASF_EN        0x00000002 /* ASF Enabled - RO */
+#define E1000_MANC_ARP_EN        0x00002000 /* Enable ARP Request Filtering */
+#define E1000_MANC_RCV_TCO_EN    0x00020000 /* Receive TCO Packets Enabled */
+#define E1000_MANC_BLK_PHY_RST_ON_IDE   0x00040000 /* Block phy resets */
+/* Enable MAC address filtering */
+#define E1000_MANC_EN_MAC_ADDR_FILTER   0x00100000
+/* Enable MNG packets to host memory */
+#define E1000_MANC_EN_MNG2HOST   0x00200000
+
+/* Receive Control */
+#define E1000_RCTL_EN             0x00000002    /* enable */
+#define E1000_RCTL_SBP            0x00000004    /* store bad packet */
+#define E1000_RCTL_UPE            0x00000008    /* unicast promiscuous enable */
+#define E1000_RCTL_MPE            0x00000010    /* multicast promiscuous enab */
+#define E1000_RCTL_LPE            0x00000020    /* long packet enable */
+#define E1000_RCTL_LBM_NO         0x00000000    /* no loopback mode */
+#define E1000_RCTL_LBM_MAC        0x00000040    /* MAC loopback mode */
+#define E1000_RCTL_LBM_TCVR       0x000000C0    /* tcvr loopback mode */
+#define E1000_RCTL_DTYP_PS        0x00000400    /* Packet Split descriptor */
+#define E1000_RCTL_RDMTS_HALF     0x00000000    /* Rx desc min threshold size */
+#define E1000_RCTL_MO_SHIFT       12            /* multicast offset shift */
+#define E1000_RCTL_MO_3           0x00003000    /* multicast offset 15:4 */
+#define E1000_RCTL_BAM            0x00008000    /* broadcast enable */
+/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
+#define E1000_RCTL_SZ_2048        0x00000000    /* Rx buffer size 2048 */
+#define E1000_RCTL_SZ_1024        0x00010000    /* Rx buffer size 1024 */
+#define E1000_RCTL_SZ_512         0x00020000    /* Rx buffer size 512 */
+#define E1000_RCTL_SZ_256         0x00030000    /* Rx buffer size 256 */
+/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
+#define E1000_RCTL_SZ_16384       0x00010000    /* Rx buffer size 16384 */
+#define E1000_RCTL_SZ_8192        0x00020000    /* Rx buffer size 8192 */
+#define E1000_RCTL_SZ_4096        0x00030000    /* Rx buffer size 4096 */
+#define E1000_RCTL_VFE            0x00040000    /* vlan filter enable */
+#define E1000_RCTL_CFIEN          0x00080000    /* canonical form enable */
+#define E1000_RCTL_CFI            0x00100000    /* canonical form indicator */
+#define E1000_RCTL_PMCF           0x00800000    /* pass MAC control frames */
+#define E1000_RCTL_BSEX           0x02000000    /* Buffer size extension */
+#define E1000_RCTL_SECRC          0x04000000    /* Strip Ethernet CRC */
+
+/*
+ * Use byte values for the following shift parameters
+ * Usage:
+ *     psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
+ *                  E1000_PSRCTL_BSIZE0_MASK) |
+ *                ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
+ *                  E1000_PSRCTL_BSIZE1_MASK) |
+ *                ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
+ *                  E1000_PSRCTL_BSIZE2_MASK) |
+ *                ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
+ *                  E1000_PSRCTL_BSIZE3_MASK))
+ * where value0 = [128..16256],  default=256
+ *       value1 = [1024..64512], default=4096
+ *       value2 = [0..64512],    default=4096
+ *       value3 = [0..64512],    default=0
+ */
+
+#define E1000_PSRCTL_BSIZE0_MASK   0x0000007F
+#define E1000_PSRCTL_BSIZE1_MASK   0x00003F00
+#define E1000_PSRCTL_BSIZE2_MASK   0x003F0000
+#define E1000_PSRCTL_BSIZE3_MASK   0x3F000000
+
+#define E1000_PSRCTL_BSIZE0_SHIFT  7            /* Shift _right_ 7 */
+#define E1000_PSRCTL_BSIZE1_SHIFT  2            /* Shift _right_ 2 */
+#define E1000_PSRCTL_BSIZE2_SHIFT  6            /* Shift _left_ 6 */
+#define E1000_PSRCTL_BSIZE3_SHIFT 14            /* Shift _left_ 14 */
+
+/* SWFW_SYNC Definitions */
+#define E1000_SWFW_EEP_SM   0x1
+#define E1000_SWFW_PHY0_SM  0x2
+#define E1000_SWFW_PHY1_SM  0x4
+#define E1000_SWFW_CSR_SM   0x8
+
+/* Device Control */
+#define E1000_CTRL_FD       0x00000001  /* Full duplex.0=half; 1=full */
+#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
+#define E1000_CTRL_LRST     0x00000008  /* Link reset. 0=normal,1=reset */
+#define E1000_CTRL_ASDE     0x00000020  /* Auto-speed detect enable */
+#define E1000_CTRL_SLU      0x00000040  /* Set link up (Force Link) */
+#define E1000_CTRL_ILOS     0x00000080  /* Invert Loss-Of Signal */
+#define E1000_CTRL_SPD_SEL  0x00000300  /* Speed Select Mask */
+#define E1000_CTRL_SPD_10   0x00000000  /* Force 10Mb */
+#define E1000_CTRL_SPD_100  0x00000100  /* Force 100Mb */
+#define E1000_CTRL_SPD_1000 0x00000200  /* Force 1Gb */
+#define E1000_CTRL_FRCSPD   0x00000800  /* Force Speed */
+#define E1000_CTRL_FRCDPX   0x00001000  /* Force Duplex */
+#define E1000_CTRL_SWDPIN0  0x00040000  /* SWDPIN 0 value */
+#define E1000_CTRL_SWDPIN1  0x00080000  /* SWDPIN 1 value */
+#define E1000_CTRL_SWDPIO0  0x00400000  /* SWDPIN 0 Input or output */
+#define E1000_CTRL_RST      0x04000000  /* Global reset */
+#define E1000_CTRL_RFCE     0x08000000  /* Receive Flow Control enable */
+#define E1000_CTRL_TFCE     0x10000000  /* Transmit flow control enable */
+#define E1000_CTRL_VME      0x40000000  /* IEEE VLAN mode enable */
+#define E1000_CTRL_PHY_RST  0x80000000  /* PHY Reset */
+
+/*
+ * Bit definitions for the Management Data IO (MDIO) and Management Data
+ * Clock (MDC) pins in the Device Control Register.
+ */
+
+/* Device Status */
+#define E1000_STATUS_FD         0x00000001      /* Full duplex.0=half,1=full */
+#define E1000_STATUS_LU         0x00000002      /* Link up.0=no,1=link */
+#define E1000_STATUS_FUNC_MASK  0x0000000C      /* PCI Function Mask */
+#define E1000_STATUS_FUNC_SHIFT 2
+#define E1000_STATUS_FUNC_1     0x00000004      /* Function 1 */
+#define E1000_STATUS_TXOFF      0x00000010      /* transmission paused */
+#define E1000_STATUS_SPEED_10   0x00000000      /* Speed 10Mb/s */
+#define E1000_STATUS_SPEED_100  0x00000040      /* Speed 100Mb/s */
+#define E1000_STATUS_SPEED_1000 0x00000080      /* Speed 1000Mb/s */
+#define E1000_STATUS_LAN_INIT_DONE 0x00000200   /* Lan Init Completion by NVM */
+#define E1000_STATUS_PHYRA      0x00000400      /* PHY Reset Asserted */
+#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
+
+/* Constants used to interpret the masked PCI-X bus speed. */
+
+#define HALF_DUPLEX 1
+#define FULL_DUPLEX 2
+
+
+#define ADVERTISE_10_HALF                 0x0001
+#define ADVERTISE_10_FULL                 0x0002
+#define ADVERTISE_100_HALF                0x0004
+#define ADVERTISE_100_FULL                0x0008
+#define ADVERTISE_1000_HALF               0x0010 /* Not used, just FYI */
+#define ADVERTISE_1000_FULL               0x0020
+
+/* 1000/H is not supported, nor spec-compliant. */
+#define E1000_ALL_SPEED_DUPLEX ( ADVERTISE_10_HALF |   ADVERTISE_10_FULL | \
+				ADVERTISE_100_HALF |  ADVERTISE_100_FULL | \
+						     ADVERTISE_1000_FULL)
+#define E1000_ALL_NOT_GIG      ( ADVERTISE_10_HALF |   ADVERTISE_10_FULL | \
+				ADVERTISE_100_HALF |  ADVERTISE_100_FULL)
+#define E1000_ALL_100_SPEED    (ADVERTISE_100_HALF |  ADVERTISE_100_FULL)
+#define E1000_ALL_10_SPEED      (ADVERTISE_10_HALF |   ADVERTISE_10_FULL)
+#define E1000_ALL_HALF_DUPLEX   (ADVERTISE_10_HALF |  ADVERTISE_100_HALF)
+
+#define AUTONEG_ADVERTISE_SPEED_DEFAULT   E1000_ALL_SPEED_DUPLEX
+
+/* LED Control */
+#define E1000_PHY_LED0_MODE_MASK          0x00000007
+#define E1000_PHY_LED0_IVRT               0x00000008
+#define E1000_PHY_LED0_MASK               0x0000001F
+
+#define E1000_LEDCTL_LED0_MODE_MASK       0x0000000F
+#define E1000_LEDCTL_LED0_MODE_SHIFT      0
+#define E1000_LEDCTL_LED0_IVRT            0x00000040
+#define E1000_LEDCTL_LED0_BLINK           0x00000080
+
+#define E1000_LEDCTL_MODE_LINK_UP       0x2
+#define E1000_LEDCTL_MODE_LED_ON        0xE
+#define E1000_LEDCTL_MODE_LED_OFF       0xF
+
+/* Transmit Descriptor bit definitions */
+#define E1000_TXD_DTYP_D     0x00100000 /* Data Descriptor */
+#define E1000_TXD_POPTS_IXSM 0x01       /* Insert IP checksum */
+#define E1000_TXD_POPTS_TXSM 0x02       /* Insert TCP/UDP checksum */
+#define E1000_TXD_CMD_EOP    0x01000000 /* End of Packet */
+#define E1000_TXD_CMD_IFCS   0x02000000 /* Insert FCS (Ethernet CRC) */
+#define E1000_TXD_CMD_IC     0x04000000 /* Insert Checksum */
+#define E1000_TXD_CMD_RS     0x08000000 /* Report Status */
+#define E1000_TXD_CMD_RPS    0x10000000 /* Report Packet Sent */
+#define E1000_TXD_CMD_DEXT   0x20000000 /* Descriptor extension (0 = legacy) */
+#define E1000_TXD_CMD_VLE    0x40000000 /* Add VLAN tag */
+#define E1000_TXD_CMD_IDE    0x80000000 /* Enable Tidv register */
+#define E1000_TXD_STAT_DD    0x00000001 /* Descriptor Done */
+#define E1000_TXD_STAT_EC    0x00000002 /* Excess Collisions */
+#define E1000_TXD_STAT_LC    0x00000004 /* Late Collisions */
+#define E1000_TXD_STAT_TU    0x00000008 /* Transmit underrun */
+#define E1000_TXD_CMD_TCP    0x01000000 /* TCP packet */
+#define E1000_TXD_CMD_IP     0x02000000 /* IP packet */
+#define E1000_TXD_CMD_TSE    0x04000000 /* TCP Seg enable */
+#define E1000_TXD_STAT_TC    0x00000004 /* Tx Underrun */
+
+/* Transmit Control */
+#define E1000_TCTL_EN     0x00000002    /* enable Tx */
+#define E1000_TCTL_PSP    0x00000008    /* pad short packets */
+#define E1000_TCTL_CT     0x00000ff0    /* collision threshold */
+#define E1000_TCTL_COLD   0x003ff000    /* collision distance */
+#define E1000_TCTL_RTLC   0x01000000    /* Re-transmit on late collision */
+#define E1000_TCTL_MULR   0x10000000    /* Multiple request support */
+
+/* Transmit Arbitration Count */
+
+/* SerDes Control */
+#define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
+
+/* Receive Checksum Control */
+#define E1000_RXCSUM_TUOFL     0x00000200   /* TCP / UDP checksum offload */
+#define E1000_RXCSUM_IPPCSE    0x00001000   /* IP payload checksum enable */
+
+/* Header split receive */
+#define E1000_RFCTL_ACK_DIS             0x00001000
+#define E1000_RFCTL_EXTEN               0x00008000
+#define E1000_RFCTL_IPV6_EX_DIS         0x00010000
+#define E1000_RFCTL_NEW_IPV6_EXT_DIS    0x00020000
+
+/* Collision related configuration parameters */
+#define E1000_COLLISION_THRESHOLD       15
+#define E1000_CT_SHIFT                  4
+#define E1000_COLLISION_DISTANCE        63
+#define E1000_COLD_SHIFT                12
+
+/* Default values for the transmit IPG register */
+#define DEFAULT_82543_TIPG_IPGT_COPPER 8
+
+#define E1000_TIPG_IPGT_MASK  0x000003FF
+
+#define DEFAULT_82543_TIPG_IPGR1 8
+#define E1000_TIPG_IPGR1_SHIFT  10
+
+#define DEFAULT_82543_TIPG_IPGR2 6
+#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7
+#define E1000_TIPG_IPGR2_SHIFT  20
+
+#define MAX_JUMBO_FRAME_SIZE    0x3F00
+
+/* Extended Configuration Control and Size */
+#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP      0x00000020
+#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE       0x00000001
+#define E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE       0x00000008
+#define E1000_EXTCNF_CTRL_SWFLAG                 0x00000020
+#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK   0x00FF0000
+#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT          16
+#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK   0x0FFF0000
+#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT          16
+
+#define E1000_PHY_CTRL_D0A_LPLU           0x00000002
+#define E1000_PHY_CTRL_NOND0A_LPLU        0x00000004
+#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008
+#define E1000_PHY_CTRL_GBE_DISABLE        0x00000040
+
+#define E1000_KABGTXD_BGSQLBIAS           0x00050000
+
+/* PBA constants */
+#define E1000_PBA_8K  0x0008    /* 8KB */
+#define E1000_PBA_16K 0x0010    /* 16KB */
+
+#define E1000_PBS_16K E1000_PBA_16K
+
+#define IFS_MAX       80
+#define IFS_MIN       40
+#define IFS_RATIO     4
+#define IFS_STEP      10
+#define MIN_NUM_XMITS 1000
+
+/* SW Semaphore Register */
+#define E1000_SWSM_SMBI         0x00000001 /* Driver Semaphore bit */
+#define E1000_SWSM_SWESMBI      0x00000002 /* FW Semaphore bit */
+#define E1000_SWSM_DRV_LOAD     0x00000008 /* Driver Loaded Bit */
+
+#define E1000_SWSM2_LOCK        0x00000002 /* Secondary driver semaphore bit */
+
+/* Interrupt Cause Read */
+#define E1000_ICR_TXDW          0x00000001 /* Transmit desc written back */
+#define E1000_ICR_LSC           0x00000004 /* Link Status Change */
+#define E1000_ICR_RXSEQ         0x00000008 /* Rx sequence error */
+#define E1000_ICR_RXDMT0        0x00000010 /* Rx desc min. threshold (0) */
+#define E1000_ICR_RXT0          0x00000080 /* Rx timer intr (ring 0) */
+#define E1000_ICR_INT_ASSERTED  0x80000000 /* If this bit asserted, the driver should claim the interrupt */
+#define E1000_ICR_RXQ0          0x00100000 /* Rx Queue 0 Interrupt */
+#define E1000_ICR_RXQ1          0x00200000 /* Rx Queue 1 Interrupt */
+#define E1000_ICR_TXQ0          0x00400000 /* Tx Queue 0 Interrupt */
+#define E1000_ICR_TXQ1          0x00800000 /* Tx Queue 1 Interrupt */
+#define E1000_ICR_OTHER         0x01000000 /* Other Interrupts */
+
+/* PBA ECC Register */
+#define E1000_PBA_ECC_COUNTER_MASK  0xFFF00000 /* ECC counter mask */
+#define E1000_PBA_ECC_COUNTER_SHIFT 20         /* ECC counter shift value */
+#define E1000_PBA_ECC_CORR_EN       0x00000001 /* ECC correction enable */
+#define E1000_PBA_ECC_STAT_CLR      0x00000002 /* Clear ECC error counter */
+#define E1000_PBA_ECC_INT_EN        0x00000004 /* Enable ICR bit 5 for ECC */
+
+/*
+ * This defines the bits that are set in the Interrupt Mask
+ * Set/Read Register.  Each bit is documented below:
+ *   o RXT0   = Receiver Timer Interrupt (ring 0)
+ *   o TXDW   = Transmit Descriptor Written Back
+ *   o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
+ *   o RXSEQ  = Receive Sequence Error
+ *   o LSC    = Link Status Change
+ */
+#define IMS_ENABLE_MASK ( \
+    E1000_IMS_RXT0   |    \
+    E1000_IMS_TXDW   |    \
+    E1000_IMS_RXDMT0 |    \
+    E1000_IMS_RXSEQ  |    \
+    E1000_IMS_LSC)
+
+/* Interrupt Mask Set */
+#define E1000_IMS_TXDW      E1000_ICR_TXDW      /* Transmit desc written back */
+#define E1000_IMS_LSC       E1000_ICR_LSC       /* Link Status Change */
+#define E1000_IMS_RXSEQ     E1000_ICR_RXSEQ     /* Rx sequence error */
+#define E1000_IMS_RXDMT0    E1000_ICR_RXDMT0    /* Rx desc min. threshold */
+#define E1000_IMS_RXT0      E1000_ICR_RXT0      /* Rx timer intr */
+#define E1000_IMS_RXQ0      E1000_ICR_RXQ0      /* Rx Queue 0 Interrupt */
+#define E1000_IMS_RXQ1      E1000_ICR_RXQ1      /* Rx Queue 1 Interrupt */
+#define E1000_IMS_TXQ0      E1000_ICR_TXQ0      /* Tx Queue 0 Interrupt */
+#define E1000_IMS_TXQ1      E1000_ICR_TXQ1      /* Tx Queue 1 Interrupt */
+#define E1000_IMS_OTHER     E1000_ICR_OTHER     /* Other Interrupts */
+
+/* Interrupt Cause Set */
+#define E1000_ICS_LSC       E1000_ICR_LSC       /* Link Status Change */
+#define E1000_ICS_RXSEQ     E1000_ICR_RXSEQ     /* Rx sequence error */
+#define E1000_ICS_RXDMT0    E1000_ICR_RXDMT0    /* Rx desc min. threshold */
+
+/* Transmit Descriptor Control */
+#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */
+#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */
+#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
+#define E1000_TXDCTL_MAX_TX_DESC_PREFETCH 0x0100001F /* GRAN=1, PTHRESH=31 */
+/* Enable the counting of desc. still to be processed. */
+#define E1000_TXDCTL_COUNT_DESC 0x00400000
+
+/* Flow Control Constants */
+#define FLOW_CONTROL_ADDRESS_LOW  0x00C28001
+#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
+#define FLOW_CONTROL_TYPE         0x8808
+
+/* 802.1q VLAN Packet Size */
+#define E1000_VLAN_FILTER_TBL_SIZE 128  /* VLAN Filter Table (4096 bits) */
+
+/* Receive Address */
+/*
+ * Number of high/low register pairs in the RAR. The RAR (Receive Address
+ * Registers) holds the directed and multicast addresses that we monitor.
+ * Technically, we have 16 spots.  However, we reserve one of these spots
+ * (RAR[15]) for our directed address used by controllers with
+ * manageability enabled, allowing us room for 15 multicast addresses.
+ */
+#define E1000_RAR_ENTRIES     15
+#define E1000_RAH_AV  0x80000000        /* Receive descriptor valid */
+
+/* Error Codes */
+#define E1000_ERR_NVM      1
+#define E1000_ERR_PHY      2
+#define E1000_ERR_CONFIG   3
+#define E1000_ERR_PARAM    4
+#define E1000_ERR_MAC_INIT 5
+#define E1000_ERR_PHY_TYPE 6
+#define E1000_ERR_RESET   9
+#define E1000_ERR_MASTER_REQUESTS_PENDING 10
+#define E1000_ERR_HOST_INTERFACE_COMMAND 11
+#define E1000_BLK_PHY_RESET   12
+#define E1000_ERR_SWFW_SYNC 13
+#define E1000_NOT_IMPLEMENTED 14
+
+/* Loop limit on how long we wait for auto-negotiation to complete */
+#define FIBER_LINK_UP_LIMIT               50
+#define COPPER_LINK_UP_LIMIT              10
+#define PHY_AUTO_NEG_LIMIT                45
+#define PHY_FORCE_LIMIT                   20
+/* Number of 100 microseconds we wait for PCI Express master disable */
+#define MASTER_DISABLE_TIMEOUT      800
+/* Number of milliseconds we wait for PHY configuration done after MAC reset */
+#define PHY_CFG_TIMEOUT             100
+/* Number of 2 milliseconds we wait for acquiring MDIO ownership. */
+#define MDIO_OWNERSHIP_TIMEOUT      10
+/* Number of milliseconds for NVM auto read done after MAC reset. */
+#define AUTO_READ_DONE_TIMEOUT      10
+
+/* Flow Control */
+#define E1000_FCRTH_RTH  0x0000FFF8     /* Mask Bits[15:3] for RTH */
+#define E1000_FCRTL_RTL  0x0000FFF8     /* Mask Bits[15:3] for RTL */
+#define E1000_FCRTL_XONE 0x80000000     /* Enable XON frame transmission */
+
+/* Transmit Configuration Word */
+#define E1000_TXCW_FD         0x00000020        /* TXCW full duplex */
+#define E1000_TXCW_PAUSE      0x00000080        /* TXCW sym pause request */
+#define E1000_TXCW_ASM_DIR    0x00000100        /* TXCW astm pause direction */
+#define E1000_TXCW_PAUSE_MASK 0x00000180        /* TXCW pause request mask */
+#define E1000_TXCW_ANE        0x80000000        /* Auto-neg enable */
+
+/* Receive Configuration Word */
+#define E1000_RXCW_IV         0x08000000        /* Receive config invalid */
+#define E1000_RXCW_C          0x20000000        /* Receive config */
+#define E1000_RXCW_SYNCH      0x40000000        /* Receive config synch */
+
+/* PCI Express Control */
+#define E1000_GCR_RXD_NO_SNOOP          0x00000001
+#define E1000_GCR_RXDSCW_NO_SNOOP       0x00000002
+#define E1000_GCR_RXDSCR_NO_SNOOP       0x00000004
+#define E1000_GCR_TXD_NO_SNOOP          0x00000008
+#define E1000_GCR_TXDSCW_NO_SNOOP       0x00000010
+#define E1000_GCR_TXDSCR_NO_SNOOP       0x00000020
+
+#define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP         | \
+			   E1000_GCR_RXDSCW_NO_SNOOP      | \
+			   E1000_GCR_RXDSCR_NO_SNOOP      | \
+			   E1000_GCR_TXD_NO_SNOOP         | \
+			   E1000_GCR_TXDSCW_NO_SNOOP      | \
+			   E1000_GCR_TXDSCR_NO_SNOOP)
+
+/* PHY Control Register */
+#define MII_CR_FULL_DUPLEX      0x0100  /* FDX =1, half duplex =0 */
+#define MII_CR_RESTART_AUTO_NEG 0x0200  /* Restart auto negotiation */
+#define MII_CR_POWER_DOWN       0x0800  /* Power down */
+#define MII_CR_AUTO_NEG_EN      0x1000  /* Auto Neg Enable */
+#define MII_CR_LOOPBACK         0x4000  /* 0 = normal, 1 = loopback */
+#define MII_CR_RESET            0x8000  /* 0 = normal, 1 = PHY reset */
+#define MII_CR_SPEED_1000       0x0040
+#define MII_CR_SPEED_100        0x2000
+#define MII_CR_SPEED_10         0x0000
+
+/* PHY Status Register */
+#define MII_SR_LINK_STATUS       0x0004 /* Link Status 1 = link */
+#define MII_SR_AUTONEG_COMPLETE  0x0020 /* Auto Neg Complete */
+
+/* Autoneg Advertisement Register */
+#define NWAY_AR_10T_HD_CAPS      0x0020   /* 10T   Half Duplex Capable */
+#define NWAY_AR_10T_FD_CAPS      0x0040   /* 10T   Full Duplex Capable */
+#define NWAY_AR_100TX_HD_CAPS    0x0080   /* 100TX Half Duplex Capable */
+#define NWAY_AR_100TX_FD_CAPS    0x0100   /* 100TX Full Duplex Capable */
+#define NWAY_AR_PAUSE            0x0400   /* Pause operation desired */
+#define NWAY_AR_ASM_DIR          0x0800   /* Asymmetric Pause Direction bit */
+
+/* Link Partner Ability Register (Base Page) */
+#define NWAY_LPAR_PAUSE          0x0400 /* LP Pause operation desired */
+#define NWAY_LPAR_ASM_DIR        0x0800 /* LP Asymmetric Pause Direction bit */
+
+/* Autoneg Expansion Register */
+#define NWAY_ER_LP_NWAY_CAPS     0x0001 /* LP has Auto Neg Capability */
+
+/* 1000BASE-T Control Register */
+#define CR_1000T_HD_CAPS         0x0100 /* Advertise 1000T HD capability */
+#define CR_1000T_FD_CAPS         0x0200 /* Advertise 1000T FD capability  */
+					/* 0=DTE device */
+#define CR_1000T_MS_VALUE        0x0800 /* 1=Configure PHY as Master */
+					/* 0=Configure PHY as Slave */
+#define CR_1000T_MS_ENABLE       0x1000 /* 1=Master/Slave manual config value */
+					/* 0=Automatic Master/Slave config */
+
+/* 1000BASE-T Status Register */
+#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
+#define SR_1000T_LOCAL_RX_STATUS  0x2000 /* Local receiver OK */
+
+
+/* PHY 1000 MII Register/Bit Definitions */
+/* PHY Registers defined by IEEE */
+#define PHY_CONTROL      0x00 /* Control Register */
+#define PHY_STATUS       0x01 /* Status Register */
+#define PHY_ID1          0x02 /* Phy Id Reg (word 1) */
+#define PHY_ID2          0x03 /* Phy Id Reg (word 2) */
+#define PHY_AUTONEG_ADV  0x04 /* Autoneg Advertisement */
+#define PHY_LP_ABILITY   0x05 /* Link Partner Ability (Base Page) */
+#define PHY_AUTONEG_EXP  0x06 /* Autoneg Expansion Reg */
+#define PHY_1000T_CTRL   0x09 /* 1000Base-T Control Reg */
+#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
+#define PHY_EXT_STATUS   0x0F /* Extended Status Reg */
+
+#define PHY_CONTROL_LB   0x4000 /* PHY Loopback bit */
+
+/* NVM Control */
+#define E1000_EECD_SK        0x00000001 /* NVM Clock */
+#define E1000_EECD_CS        0x00000002 /* NVM Chip Select */
+#define E1000_EECD_DI        0x00000004 /* NVM Data In */
+#define E1000_EECD_DO        0x00000008 /* NVM Data Out */
+#define E1000_EECD_REQ       0x00000040 /* NVM Access Request */
+#define E1000_EECD_GNT       0x00000080 /* NVM Access Grant */
+#define E1000_EECD_PRES      0x00000100 /* NVM Present */
+#define E1000_EECD_SIZE      0x00000200 /* NVM Size (0=64 word 1=256 word) */
+/* NVM Addressing bits based on type (0-small, 1-large) */
+#define E1000_EECD_ADDR_BITS 0x00000400
+#define E1000_NVM_GRANT_ATTEMPTS   1000 /* NVM # attempts to gain grant */
+#define E1000_EECD_AUTO_RD          0x00000200  /* NVM Auto Read done */
+#define E1000_EECD_SIZE_EX_MASK     0x00007800  /* NVM Size */
+#define E1000_EECD_SIZE_EX_SHIFT     11
+#define E1000_EECD_FLUPD     0x00080000 /* Update FLASH */
+#define E1000_EECD_AUPDEN    0x00100000 /* Enable Autonomous FLASH update */
+#define E1000_EECD_SEC1VAL   0x00400000 /* Sector One Valid */
+#define E1000_EECD_SEC1VAL_VALID_MASK (E1000_EECD_AUTO_RD | E1000_EECD_PRES)
+
+#define E1000_NVM_RW_REG_DATA   16   /* Offset to data in NVM read/write registers */
+#define E1000_NVM_RW_REG_DONE   2    /* Offset to READ/WRITE done bit */
+#define E1000_NVM_RW_REG_START  1    /* Start operation */
+#define E1000_NVM_RW_ADDR_SHIFT 2    /* Shift to the address bits */
+#define E1000_NVM_POLL_WRITE    1    /* Flag for polling for write complete */
+#define E1000_NVM_POLL_READ     0    /* Flag for polling for read complete */
+#define E1000_FLASH_UPDATES  2000
+
+/* NVM Word Offsets */
+#define NVM_ID_LED_SETTINGS        0x0004
+#define NVM_INIT_CONTROL2_REG      0x000F
+#define NVM_INIT_CONTROL3_PORT_B   0x0014
+#define NVM_INIT_3GIO_3            0x001A
+#define NVM_INIT_CONTROL3_PORT_A   0x0024
+#define NVM_CFG                    0x0012
+#define NVM_ALT_MAC_ADDR_PTR       0x0037
+#define NVM_CHECKSUM_REG           0x003F
+
+#define E1000_NVM_CFG_DONE_PORT_0  0x40000 /* MNG config cycle done */
+#define E1000_NVM_CFG_DONE_PORT_1  0x80000 /* ...for second port */
+
+/* Mask bits for fields in Word 0x0f of the NVM */
+#define NVM_WORD0F_PAUSE_MASK       0x3000
+#define NVM_WORD0F_PAUSE            0x1000
+#define NVM_WORD0F_ASM_DIR          0x2000
+
+/* Mask bits for fields in Word 0x1a of the NVM */
+#define NVM_WORD1A_ASPM_MASK  0x000C
+
+/* For checksumming, the sum of all words in the NVM should equal 0xBABA. */
+#define NVM_SUM                    0xBABA
+
+/* PBA (printed board assembly) number words */
+#define NVM_PBA_OFFSET_0           8
+#define NVM_PBA_OFFSET_1           9
+
+#define NVM_WORD_SIZE_BASE_SHIFT   6
+
+/* NVM Commands - SPI */
+#define NVM_MAX_RETRY_SPI          5000 /* Max wait of 5ms, for RDY signal */
+#define NVM_READ_OPCODE_SPI        0x03 /* NVM read opcode */
+#define NVM_WRITE_OPCODE_SPI       0x02 /* NVM write opcode */
+#define NVM_A8_OPCODE_SPI          0x08 /* opcode bit-3 = address bit-8 */
+#define NVM_WREN_OPCODE_SPI        0x06 /* NVM set Write Enable latch */
+#define NVM_RDSR_OPCODE_SPI        0x05 /* NVM read Status register */
+
+/* SPI NVM Status Register */
+#define NVM_STATUS_RDY_SPI         0x01
+
+/* Word definitions for ID LED Settings */
+#define ID_LED_RESERVED_0000 0x0000
+#define ID_LED_RESERVED_FFFF 0xFFFF
+#define ID_LED_DEFAULT       ((ID_LED_OFF1_ON2  << 12) | \
+			      (ID_LED_OFF1_OFF2 <<  8) | \
+			      (ID_LED_DEF1_DEF2 <<  4) | \
+			      (ID_LED_DEF1_DEF2))
+#define ID_LED_DEF1_DEF2     0x1
+#define ID_LED_DEF1_ON2      0x2
+#define ID_LED_DEF1_OFF2     0x3
+#define ID_LED_ON1_DEF2      0x4
+#define ID_LED_ON1_ON2       0x5
+#define ID_LED_ON1_OFF2      0x6
+#define ID_LED_OFF1_DEF2     0x7
+#define ID_LED_OFF1_ON2      0x8
+#define ID_LED_OFF1_OFF2     0x9
+
+#define IGP_ACTIVITY_LED_MASK   0xFFFFF0FF
+#define IGP_ACTIVITY_LED_ENABLE 0x0300
+#define IGP_LED3_MODE           0x07000000
+
+/* PCI/PCI-X/PCI-EX Config space */
+#define PCI_HEADER_TYPE_REGISTER     0x0E
+#define PCIE_LINK_STATUS             0x12
+
+#define PCI_HEADER_TYPE_MULTIFUNC    0x80
+#define PCIE_LINK_WIDTH_MASK         0x3F0
+#define PCIE_LINK_WIDTH_SHIFT        4
+
+#define PHY_REVISION_MASK      0xFFFFFFF0
+#define MAX_PHY_REG_ADDRESS    0x1F  /* 5 bit address bus (0-0x1F) */
+#define MAX_PHY_MULTI_PAGE_REG 0xF
+
+/* Bit definitions for valid PHY IDs. */
+/*
+ * I = Integrated
+ * E = External
+ */
+#define M88E1000_E_PHY_ID    0x01410C50
+#define M88E1000_I_PHY_ID    0x01410C30
+#define M88E1011_I_PHY_ID    0x01410C20
+#define IGP01E1000_I_PHY_ID  0x02A80380
+#define M88E1111_I_PHY_ID    0x01410CC0
+#define GG82563_E_PHY_ID     0x01410CA0
+#define IGP03E1000_E_PHY_ID  0x02A80390
+#define IFE_E_PHY_ID         0x02A80330
+#define IFE_PLUS_E_PHY_ID    0x02A80320
+#define IFE_C_E_PHY_ID       0x02A80310
+#define BME1000_E_PHY_ID     0x01410CB0
+#define BME1000_E_PHY_ID_R2  0x01410CB1
+#define I82577_E_PHY_ID      0x01540050
+#define I82578_E_PHY_ID      0x004DD040
+
+/* M88E1000 Specific Registers */
+#define M88E1000_PHY_SPEC_CTRL     0x10  /* PHY Specific Control Register */
+#define M88E1000_PHY_SPEC_STATUS   0x11  /* PHY Specific Status Register */
+#define M88E1000_EXT_PHY_SPEC_CTRL 0x14  /* Extended PHY Specific Control */
+
+#define M88E1000_PHY_PAGE_SELECT   0x1D  /* Reg 29 for page number setting */
+#define M88E1000_PHY_GEN_CONTROL   0x1E  /* Its meaning depends on reg 29 */
+
+/* M88E1000 PHY Specific Control Register */
+#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
+#define M88E1000_PSCR_MDI_MANUAL_MODE  0x0000  /* MDI Crossover Mode bits 6:5 */
+					       /* Manual MDI configuration */
+#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020  /* Manual MDIX configuration */
+/* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */
+#define M88E1000_PSCR_AUTO_X_1000T     0x0040
+/* Auto crossover enabled all speeds */
+#define M88E1000_PSCR_AUTO_X_MODE      0x0060
+/*
+ * 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold)
+ * 0=Normal 10BASE-T Rx Threshold
+ */
+#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
+
+/* M88E1000 PHY Specific Status Register */
+#define M88E1000_PSSR_REV_POLARITY       0x0002 /* 1=Polarity reversed */
+#define M88E1000_PSSR_DOWNSHIFT          0x0020 /* 1=Downshifted */
+#define M88E1000_PSSR_MDIX               0x0040 /* 1=MDIX; 0=MDI */
+/* 0=<50M; 1=50-80M; 2=80-110M; 3=110-140M; 4=>140M */
+#define M88E1000_PSSR_CABLE_LENGTH       0x0380
+#define M88E1000_PSSR_SPEED              0xC000 /* Speed, bits 14:15 */
+#define M88E1000_PSSR_1000MBS            0x8000 /* 10=1000Mbs */
+
+#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
+
+/*
+ * Number of times we will attempt to autonegotiate before downshifting if we
+ * are the master
+ */
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X   0x0000
+/*
+ * Number of times we will attempt to autonegotiate before downshifting if we
+ * are the slave
+ */
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK  0x0300
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X    0x0100
+#define M88E1000_EPSCR_TX_CLK_25      0x0070 /* 25  MHz TX_CLK */
+
+/* M88EC018 Rev 2 specific DownShift settings */
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK  0x0E00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X    0x0800
+
+#define I82578_EPSCR_DOWNSHIFT_ENABLE          0x0020
+#define I82578_EPSCR_DOWNSHIFT_COUNTER_MASK    0x001C
+
+/* BME1000 PHY Specific Control Register */
+#define BME1000_PSCR_ENABLE_DOWNSHIFT   0x0800 /* 1 = enable downshift */
+
+
+#define PHY_PAGE_SHIFT 5
+#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
+                           ((reg) & MAX_PHY_REG_ADDRESS))
+
+/*
+ * Bits...
+ * 15-5: page
+ * 4-0: register offset
+ */
+#define GG82563_PAGE_SHIFT        5
+#define GG82563_REG(page, reg)    \
+	(((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
+#define GG82563_MIN_ALT_REG       30
+
+/* GG82563 Specific Registers */
+#define GG82563_PHY_SPEC_CTRL           \
+	GG82563_REG(0, 16) /* PHY Specific Control */
+#define GG82563_PHY_PAGE_SELECT         \
+	GG82563_REG(0, 22) /* Page Select */
+#define GG82563_PHY_SPEC_CTRL_2         \
+	GG82563_REG(0, 26) /* PHY Specific Control 2 */
+#define GG82563_PHY_PAGE_SELECT_ALT     \
+	GG82563_REG(0, 29) /* Alternate Page Select */
+
+#define GG82563_PHY_MAC_SPEC_CTRL       \
+	GG82563_REG(2, 21) /* MAC Specific Control Register */
+
+#define GG82563_PHY_DSP_DISTANCE    \
+	GG82563_REG(5, 26) /* DSP Distance */
+
+/* Page 193 - Port Control Registers */
+#define GG82563_PHY_KMRN_MODE_CTRL   \
+	GG82563_REG(193, 16) /* Kumeran Mode Control */
+#define GG82563_PHY_PWR_MGMT_CTRL       \
+	GG82563_REG(193, 20) /* Power Management Control */
+
+/* Page 194 - KMRN Registers */
+#define GG82563_PHY_INBAND_CTRL         \
+	GG82563_REG(194, 18) /* Inband Control */
+
+/* MDI Control */
+#define E1000_MDIC_REG_SHIFT 16
+#define E1000_MDIC_PHY_SHIFT 21
+#define E1000_MDIC_OP_WRITE  0x04000000
+#define E1000_MDIC_OP_READ   0x08000000
+#define E1000_MDIC_READY     0x10000000
+#define E1000_MDIC_ERROR     0x40000000
+
+/* SerDes Control */
+#define E1000_GEN_POLL_TIMEOUT          640
+
+#endif /* _E1000_DEFINES_H_ */